precise. compact. reliable. - BCK Holland
Transcript of precise. compact. reliable. - BCK Holland
precise. compact. reliable.
Complete catalogue 2017/2018
ContentsVetter small conveyors / Our experience – your future 4 – 5
Drive technology 6 – 7
Internal drive 8 – 19
Transverse drive 20 – 27
Centre drive 28 – 31
Transmitted light 32 – 41
Kit and custom solutions 42 – 49
Conveyor belts 50 – 53
Controllers 54 – 57
International offices 58
Contact:
Vetter Kleinförderbänder GmbHEinsteinstraße 8
D-89179 BeimerstettenTel.: +49 7348 967485-0Fax: +49 7348 967485-99Email: [email protected]: www.vetter-band.de
Our catalogue and the descriptions it contains were created with the utmost care. Nevertheless, we are unable to assume any liability for the completeness or correctness of the information provided, i.e. errors and omissions are excepted. We also reserve the right to make any technical changes to the products during the term of the catalogue. This catalogue supersedes all previous catalogues.
© Vetter Kleinförderbänder GmbHWe reserve the right to modifications. Version 08.2017.
Vetter small conveyorsOur experience – your future
4
With years of experience and leading-edge know-how in the area of conveying technology, we are able to foresee new application areas. We develop our conveyors with a view to the future and at the highest levels.Our creativity and power of innovation are geared to your re-quirements – we are always ready to rise to new challenges.
Quality and service
You benefit from competent consulting and reliable service. You can rely on:
•Highlyqualifiedexperts
•Adherencetoschedules,reliabilityandshortdeliverytimes
•Relationshipswithourbusinesspartnerswhicharebased on partnership
•Highdevelopmentflexibility
We meticulously adapt the design of our conveyors to your specific requirements.
5
1989 Foundation of VETTER Engineeringby engineer and designer Otto Vetter
1993 Small conveyors with internal motorOtto Vetter is awarded silver medals for his first “motorless” conveyor at the “International Trade Fair – Ideas, Inventions, New Products” in Nurem-berg and at the “Inventions Exhibition” in Geneva one year later.
2011 Vetter small conveyors under new managementOtto Vetter retires. Dirk Steinmann takes over the business and founds “Vetter Kleinförderbänder GmbH” in October 2011.
2012 Move to larger premisesIn the first half of 2012, the company hires additional staff and moves to larger premises in Beimerstetten. Further offices abroad are established.
Always moving ...The most important developments and innovations
2013 •Transmittedlightunitsintegratedintheconveyorallowforimagerecognitionwithoutinterferingreflexesandshadows.•ThesuccessfulQseriesdesignedforuseunderadverseenvironmental conditions can be reliably sealed against the ingress of liquids and dust.•ThenewBK-30series(kit)breaksnewgroundforcustomsolutions.•ThedevelopmentoftheVR-30-15-INTmicrocontrollertakesthe potential of conveyor technology to new dimensions: the intelligent controller provides high power density at an extremely compact size.
2014 •Smallconveyorswithknifeedgeensureevensimplerhandlingat critical transfer points without requiring additional handling systems.•Thenew“FR-40-80-Q-P”conveyormeetsallhygienicrequirements involved in, for example, the production of food and pharmaceutical products and excels with simple cleanability.
2015 • All Vetter small conveyors feature state-of-the-art drive technology: The entire product range is converted to Faulhaber brushless gear motors with integrated control electronics. This is complemented by two units for reference values from Vetter.
2016 •Inordertoallowforautomatictransferofevenextremelysmallpartsat critical interfaces, the “knife edge” is made available for additional sizes of the Vetter product range.•Thetransmittedlightunitsforimagerecognitionintegratedinthe conveyor belt are equipped with new LED technology and now offer various operating modes such as continuous light, trigger mode and dimming.•Thepowerful“centredrive”isnowavailableinthekitsystemand complements the range for custom solutions.•Theuseofmagneticfoilbreaksnewgroundintheareaofautomation.
Managing partnerDirk SteinmannGraduateEngineer(BA)MechanicalEngineering
Vetter small conveyors with Faulhaber drive technology
6
AllVettersmallconveyorsfeaturestate-of-the-artdrivetech-nology.Allmodels(withtheexceptionofFR-12-20)useECmotors(electronicallycommutatedbrushlessDCmotors)withinte-grated speed controller.
Your benefits:
No interference contoursThe electronic control system is now integrated in thehousing of the small conveyors along with the gear motors – typically Vetter.
Service made easy:The new generation of motors is mechanically fully com-patible with the brushed motors used for more than 20 years.Replacement is considerably facilitated by electrical plugconnectors.
You are in control:
Applyvoltage–done!
Allyouneedisa24VDCpowersupplyifyouwanttooperateyour Vetter small conveyor in the most simple way. The input for the direction of rotation is connected to 24 V DC or 0 V DC (GND)which determines the conveying direction.The ana-logueinputisconnectedto0VDC(GND)andtheconveyorstarts with the factory programmed speed, see .
Referencespeedviaanaloguesignal(0–10VDC)
If you want to operate with different speeds, simply provide a corresponding signal via the analogue input: in the range from 0.5 to 0.9 V DC, the conveyor is at a standstill, see .The full speed range of the motor is available from 1 to 10 V DC, see .From 10 to 11 V DC, you get approximately 110 % of the specified nominal velocity.
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
7
The analogue signal can be provided by various units:
Your controller:PLC with analogue output0 – 10 V DC for reference speed
Vetter reference speed unit VSW-11:Input: 24 V DCOutput: 0 – 11 V DCReferencespeedviapotentiometer
Vetter reference speed unit VR-24-SW-11 with integrated power supply unit:Input:100–240VAC/50–60Hz/1.3AOutput1:0–11VDC(settingviafoilkeypad)Output2:24VDC,2A
InthecaseofVettersmallconveyorstypesFR-20-20-MandFR-20-40, the reference value units are integrated in thehousing; thereferencevaluescanbeeasilysetvia the+/-keys. It is also possible to use an external analogue signal from 0 – 10 V DC.
You determine the cycle:The small conveyor can also operate cyclically via the ana-logue signal. If you use programmed acceleration and de-celeration ramps, this is easy on the mechanical system and helps to ensure a long service life of our products.Due to the brushless technology, high acceleration or de-celeration currents do not cause wear of the motors.
You determine where things move:The speed controllers integrated in the motor feature an input for the direction of rotation. This way, you can easily change the conveying direction.
You know where things stand:The signal output provides 6 pulses per motor revolution which can be processed by your controller. This lets you im-plement positioning tasks without additional encoders. We would be happy to support you in calculating the resolution.
OVERVIEWConveyor type Housing
heightHousing width Belt width Max. conveyed
loadConveyor speed Page
FR-12-20 12 mm 20 mm 17 mm 2 N 1.5m/min 10
FR-20-40 20 mm 40 mm 32 mm 5 N 2–8m/min 11
or
15 N 0.7–3m/min
FR-30-60-200 30 mm 60 mm 50 mm 20 N 2–10m/min 12
or
40 N 0.5–3.5m/min
FR-30-60 30 mm 60 mm 50 mm 20 N 2–10m/min 13
or
40 N 0.5–3.5m/min
FR-40-80 40 mm 80 mm 65 mm 50 N 2–10m/min 14
or
100 N 0.5–3m/min
ZR-40-80 40 mm 80 mm 50 mm 50 N 2–10m/min 15
or
100 N 0.5–3m/min
FR-40-120 40 mm 120 mm 105 mm 50 N 2–10m/min 16
or
100 N 0.5–3m/min
FR-40-160 40 mm 160 mm 145 mm 50 N 2–10m/min 17
or
100 N 0.5–3m/min
FR-40-200 40 mm 200 mm 185 mm 50 N 2–10m/min 18
or
100 N 0.5–3m/min
Internal drive8
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
FR-12-20
FR-20-40
ZR-40-80
FR-40-120
FR-40-200
FR-30-60-200
FR-30-60
FR-40-80
FR-40-160
BENEFITSInnenlie
Internal drive
• No interference contours
• Simple design and easy integration into existing systems
• Easy installation
•Useofitem aluminium profiles
•Useofhigh-gradematerials: Stainless steel and aluminium
• Wide selection of conveyor belts, also for custom solutions
• Custom solutions to specifications
• Low voltage
- No special safety precautions required
• Excellent serviceability: Conveyors integrated into existing automation systems can be easily disassembled
• State-of-the-art drive technology - EC motor (brushless DC motor) - Integrated electronic speed controller operated via integrated foil keypad or external analogue signal 0 – 10 V DC
- Low current input at high conveying capacity
9
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Standard centre distances in mm (availableatshortnotice)
100 150 200
Max. conveyed load in N Conveyor speed m/min Supply voltage
2 1.5 Motor: 6 V DC
Anyconveyingdirection
Conveyor belt
Translucent(FDA) Others on request
Belt width
17 mm
FR-12-20 Conveyor with internal drive10
Housing height 12 mm I Housing width 20 mm
Conveyorbelt:Translucent(FDA)
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
200
150
100
0.9
0,9
17Be
lt w
idth
20Ho
usin
g w
idth
Approx.50
Ø12
Ø12
190
140
90
55
55
55
10
10
10
2xM3,4deep(bothsides)
2xM3,4deep(bothsides)
4-pinsocketwithflangeconnectorwithcable approx. 2 m(4x0.14mm2)
2xM3,4deep(bothsides)
0,9
Ø12
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
300 350 400 450 500 600 700 800 900 1,000 Special centre distances on request
Max. conveyed load in N Conveyor speed m/min Supply voltage
5 2 – 8 24 V DC
15 0.7 – 3 24 V DC
Integrated speed controller
Conveyor belt
1E/PW02,white(FDA,antistatic) Others on request
Belt width
32 mm
FR-20-40 Conveyor with internal drive 11
Housing height 20 mm I Housing width 40 mm
Conveyorbelt:1E/PW02,green(FDA,antistatic)
Foil keypad for speed setting
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
Preferred conveying direction
Centre distance
3210 Ø2
2Be
lt w
idth
Rollerdiameter
36Sl
idin
g pl
ate
wid
th
40Ho
usin
g w
idth
Item aluminium profile with T grooves 5 mm
Foil keypad for speed setting
Sliding plate V2A,1.5mm
4 x M4, 7 deep(bothsides)
Standard beltapprox. 0.8 mm thick
Gear motor cable approx.2.5m(5x0.25mm2)
220Approx.
3025
25
Centre distances in mm (availableatshortnotice)
200
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
9 3 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0
Controllable / analogue signal 1 – 10 V DC
2 – 10 0.5 – 3.5 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 2 – 10 24 V DC
40 0.5 – 3.5 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
50 mm
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
FR-30-60-200 Conveyor with internal drive12
Housing height 30 mm I Housing width 60 mm
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
Preferred conveying direction
50Be
lt w
idth
14
60Ho
usin
g w
idth
Gear motor cable approx.2.5m(6x0.14mm2)
4 x M4, 7 deep(bothsides)
Standard beltapprox. 1.3 mm thick
Ø30Rollerdiameter
Approx.200
20160
Preferred conveying direction
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
Centre distances in mm (availableatshortnotice)
300(withoutitem-profile) 400 450 500 600 700 800 900 1,000 1,200 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
9 3 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0
Controllable / analogue signal 1 – 10 V DC
2 – 10 0.5 – 3.5 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 2 – 10 24 V DC
40 0.5 – 3.5 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
50 mm
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
FR-30-60 Conveyor with internal drive 13
Housing height 30 mm I Housing width 60 mm
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Vetter small conveyor installed in punching system
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
14
Preferred conveying direction
Preferred conveying direction
Standard beltapprox. 1.3 mm thick
4 x M4, 7 deep(bothsides)
Item aluminium profile with T grooves 6 mm
Centre distanceApprox.
30 270
160 40
Gear motor cable approx.2.5m(6x0.14mm2)
Ø30Rollerdiameter
50Be
lt w
idth
60Ho
usin
g w
idth
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
8 2.7 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0
Controllable / analogue signal 1 – 10 V DC
2 – 10 0.5 – 3 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
50 2 – 10 24 V DC
100 0.5 – 3 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
65 mm
FR-40-80 Conveyor with internal drive14
Housing height 40 mm I Housing width 80 mm
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Ø44
Rollerdiameter
Standard beltapprox. 1.3 mm thick
Item aluminium profile with T grooves 5 mm
Sliding plate V2A,2mm
65Be
lt w
idth
75Sl
idin
g pl
ate
wid
th80
Hous
ing
wid
th
Preferred conveying direction
Preferred conveying direction
Centre distance
130Approx.80
Gear motor cable approx.2.5m(6x0.14mm2)
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
Centre distances in mm
Accordingtoagreedspecifications
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
9 3 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0
Controllable / analogue signal 1 – 10 V DC
2 – 10 0.5 – 3 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
50 2 – 10 24 V DC
100 0.5 – 3 24 V DC
Conveyor belt
TimingbeltAT-10 Optional: TimingbeltATN-10(withnutinserts)
Belt width
50 mm
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
ZR-40-80 Conveyor with internal drive 15
Housing height 40 mm I Housing width 80 mm
Conveyorbelt:TimingbeltAT-10
Example:TimingbeltATN-10withnutinserts
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
Sliding plateV2A,2mm
Item aluminium profile with T grooves 5 mm
A A
TimingbeltAT-10
Gear motor cable approx.2.5m(6x0.14mm2)
Belt
wid
th5025
2.5
4.5 2
53.5
10
M4
Preferred conveying direction
Preferred conveying direction
Centre distance
Approx. 80 130
50
Belt
wid
th
75Sl
idin
g pl
ate
wid
th80
Hous
ing
wid
th
50 °Ø6
A-A(1:1)
Option:TimingbeltATN-10withnutinserts
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
8 2.7 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0
Controllable / analogue signal 1 – 10 V DC
2 – 10 0.5 – 3 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
50 2 – 10 24 V DC
100 0.5 – 3 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
105 mm
FR-40-120 Conveyor with internal drive16
Housing height 40 mm I Housing width 120 mm
Special conveyor belt Grip
Example: Special conveyor belt with T20 cams
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
Ø44
Rollerdiameter
105
Belt
wid
th
Centre distance
Approx.80 130Sliding plate V2A,2mm
Standard beltapprox. 1.3 mm thick
Item aluminium profile with T grooves 5 mm
115
Slid
ing
plat
e w
idth
120
Hous
ing
wid
th
Preferred conveying direction
Preferred conveying direction
Gear motor cable approx.2.5m(6x0.14mm2)
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
8 2.7 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0
Controllable / analogue signal 1 – 10 V DC
2 – 10 0.5 – 3 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
50 2 – 10 24 V DC
100 0.5 – 3 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
145 mm
FR-40-160 Conveyor with internal drive 17
Housing height 40 mm I Housing width 160 mm
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Example:U-shapeslidingplateusedaslateralguide
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
Ø44
Rollerdiameter
145
Belt
wid
th
Centre distance
Approx.80 130Sliding plate V2A,2mm
Standard beltapprox. 1.3 mm thick
Item aluminium profile with T grooves 5 mm
155
Slid
ing
plat
e w
idth
160
Hous
ing
wid
th
Preferred conveying direction
Preferred conveying direction
Gear motor cable approx.2.5m(6x0.14mm2)
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
8 2.7 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0
Controllable / analogue signal 1 – 10 V DC
2 – 10 0.5 – 3 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
50 2 – 10 24 V DC
100 0.5 – 3 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
185 mm
FR-40-200 Conveyor with internal drive18
Housing height 40 mm I Housing width 200 mm
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Ø44
Rollerdiameter
185
Belt
wid
th
Centre distanceApprox.80 130
Sliding plate V2A,2mm
Standard beltapprox. 1.3 mm thick
Item aluminium profile with T grooves 5 mm
195
Slid
ing
plat
e w
idth
200
Hous
ing
wid
th
Preferred conveying direction
Preferred conveying direction
Gear motor cable approx.2.5m(6x0.14mm2)
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
Example:FR-30-60Ttypemounting Example:FR-40-80withspecialconveyorbeltGrip Example:ZR-40-80-ATN-10withnutinserts
Example:FR-20-40withprofilesandlateralguide
OVERVIEWConveyor type Housing
heightHousing width Belt width Max. conveyed
loadConveyor speed Page
FR-40-80-Q 40 mm 80 mm 65 mm 20 N 5–30m/min 22
40 N 4–24m/min
100 N 1.5–10m/min
FR-40-80-Q-P 40 mm 80 mm 65 mm 20 N 5–30m/min 23
40 N 4–24m/min
100 N 1.5–10m/min
FR-40-120-Q 40 mm 120 mm 105 mm 20 N 5–30m/min 24
40 N 4–24m/min
100 N 1.5–10m/min
FR-40-160-Q 40 mm 160 mm 145 mm 20 N 5–30m/min 25
40 N 4–24m/min
100 N 1.5–10m/min
FR-40-200-Q 40 mm 200 mm 185 mm 20 N 5–30m/min 26
40 N 4–24m/min
100 N 1.5–10m/min
Transverse drive20
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
FR-40-80-Q
FR-40-80-Q-P
FR-40-120-Q
FR-40-160-Q
FR-40-200-Q
BENEFITS
Transverse drive
• Higher belt speeds
• Drive housing can be optionally sealed against the ingress of dust and liquids
• Motor for the most part integrated into housing, external contact protection cover
• No interference contour over height
• Simple design and easy integration into existing systems
• Easy installation
• Useofitem aluminium profiles
• Useofhigh-gradematerials: Stainless steel and aluminium
• Wide selection of conveyor belts, also for custom solutions
• Custom solutions to specifications
• 24 V extra low voltage
- No special safety precautions required
• Excellent serviceability: Conveyors integrated into existing automation systems can be easily disassembled
• State-of-the-art driving technology - EC motor (brushless DC motor) - Integrated electronic speed controller operated via integrated foil keypad or external analogue signal 0 – 10 V DC
- Low current input at high conveying capacity
21
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
300 350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference valueunitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
65 mm
FR-40-80-Q Conveyor with transverse drive22
Housing height 40 mm I Housing width 80 mm
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Example: Inclined conveyor
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Preferred conveying direction
25
Ø44
Rollerdiameter
65
Belt
wid
th
80
Centre distance
Approx.80 130
Sliding plate V2A2,mm
Standard beltapprox. 1.3 mm thick
Item aluminium profile with T grooves 5 mm
Gear motor cable approx.2.5m(6x0.14mm2)
75Sl
idin
g pl
ate
wid
th
80Ho
usin
g w
idth
Preferred conveying direction
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm
Accordingtoagreedspecifications
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference valueunitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
2E/PHB03(FDA,antistatic) Others on request
Belt width
65 mm
FR-40-80-Q-P Conveyor with transverse drive 23
Housing height 40 mm I Housing width 80 mm
Additional BENEFITS
For use in food and pharmaceutical applications• Drive housing sealed against the ingress of dust and liquids
• Materials: Stainless steel and FDA plastics, sealed stainless steel ball bearing
• Simple mounting and disassembly of conveyor belt for easy cleaning
• Design optimized for hygiene
•Useofsolidplasticparts
- Simple design and easy integration into existing systems
- Mounting and fastening holes easy to produce in the solid plastic part
For use in food and pharmaceutical applications
Specialconveyorbelt:2E/PHB03nubtopbelt,blue(FDA,antistatic)
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
* screw joints: through bore holes, blind holes for thread inserts, etc.
Areafor*
Centre distance
Ø44
Roller
diam
eter
Preferred conveying direction
130
Approx.80 130
60
180
65
Belt
wid
th
80Ho
usin
g w
idth
2590
Gear motor cable approx.2.5m(6x0.14mm2)
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
300 350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference valueunitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
105 mm
FR-40-120-Q Conveyor with transverse drive24
Housing height 40 mm I Housing width 120 mm
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Sliding plate V2A,2mm
Standard beltapprox. 1.3 mm thick
Item aluminium profile with T grooves 5 mm
Preferred conveying direction
Preferred conveying direction
Gear motor cable approx.2.5m(6x0.14mm2)
Ø44
Rollerdiameter
Approx.80
Centre distance
130
105
Belt
wid
th
115
Slid
ing
plat
e w
idth
120
Hous
ing
wid
th25
40
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
300 350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference valueunitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
145 mm
FR-40-160-Q Conveyor with transverse drive 25
Housing height 40 mm I Housing width 160 mm
Conveyorbelt:2E/PG02,green(FDA,antistatic)
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Sliding plateV2A,2mm
Standard beltapprox. 1.3 mm thick
Item aluminium profile with T grooves 5 mm
Gear motor cable approx.2.5m(6x0.14mm2)
Preferred conveying direction
Preferred conveying direction
Ø44
Rollerdiameter
Centre distance
130Approx. 80
145
Belt
wid
th
155
Slid
ing
plat
e w
idth
160
Hous
ing
wid
th25
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
300 350 400 450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference valueunitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
2E/PG02,green(FDA,antistatic) Others on request
Belt width
185 mm
FR-40-200-Q Conveyor with transverse drive26
Housing height 40 mm I Housing width 200 mm
Special conveyor belt: Grip
Detail: Special conveyor belt – grip surface
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Ø44
Rollerdiameter Centre distance
Approx.80 130Sliding plateV2A,2mm
Item aluminium profile with T grooves 5 mm
Standard beltapprox. 1.3 mm thick
Preferred conveying direction
185
Belt
wid
th
195
Slid
ing
plat
e w
idth
200
Hous
ing
wid
th25
Preferred conveying direction
Gear motor cable approx.2.5m(6x0.14mm2)
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
Example: Feed for husking machine
OVERVIEWConveyor type Housing
heightHousing width Belt width Max. conveyed
loadConveyor speed Page
FR-20-20-M 20 mm 20 mm 15 mm 30 N 2–40m/min 30
Centre drive28
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
FR-20-20-M
BENEFITS
Centre drive
• High performance of Conveyors with centre drive
• Conveyors can be integrated into your automation system at any position
• Flexible track distances: For example, you can integrate a completely independent conveyor into your system every 20 mm
• Conveyors with centre drive can be arranged in parallel in any way with or without clearance
• The drive can be moved to any position along the entire length of the profile
• Different belts directly mounted next to each other can be controlled independently
• Wide speed range: 2 – 40 m/min
• State-of-the-art drive technology - EC-motor (brushless DC motor) - Integrated electronic speed controller operated via integrated foil keypad or external analogue signal 0 – 10 V DC
- Low current input at high conveying capacity
29
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Centre distances in mm (availableatshortnotice)
200 300 400 500 600 700 800 900 1,000 Special centre distances on request
Max. conveyed load in N Conveyor speed m/min Supply voltage
30 2 – 40 24 V DC
Integrated speed controller
Conveyor belt
1E/PW02,white(FDA,antistatic) Others on request
Belt width
15 mm
FR-20-20-M Centre drive conveyor30
Housing height 20 mm I Housing width 20 mm
FR-20-20-M
Example: Easy adjustment of belt run
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Item aluminium profile with T grooves 5 mm
Screw for transverse adjustment of belt
Cableapprox.2.5m(6x0.14mm2)
Screw for transverse adjustment of beltVariable
M5x10/14Foil keypad for speed setting
Slidingplate:Aluminium
Centre distance
6080
100
25 25
114
112
140(upperedgeofbelt)
10
1520
Ø24
Example: Parts buffer Adjustmentmechanismwithoutinterferencecontours Knife edge possible at both sides
Example: Two small conveyors mounted one after the other
Transmitted light32
OVERVIEWConveyor type Housing
heightHousing width Belt width Max. conveyed
loadConveyor speed Page
FR-12-20-DL 12 mm 20 mm 17 mm 2 N 1.5m/min 34
Internal drive
BK-20-20-DL 20 mm 20 mm 17 mm Accordingtoagreed Accordingtoagreed 35
Kit specifications specifications
FR-20-40-DL 20 mm 40 mm 32 mm 5 N 2–8m/min 36
Internal drive or
15 N 0.7–3m/min
BK-20-40-DL 20 mm 40 mm 32 mm Accordingtoagreed Accordingtoagreed 37
Kit specifications specifications
FR-40-80-Q-DL 40 mm 80 mm 65 mm 20 N 5–30m/min 38
Transverse drive 40 N 4–24m/min
100 N 1.5–10m/min
FR-40-120-Q-DL 40 mm 120 mm 105 mm 20 N 5–30m/min 39
Transverse drive 40 N 4–24m/min
100 N 1.5–10m/min
FR-40-160-Q-DL 40 mm 160 mm 145 mm 20 N 5–30m/min 40
Transverse drive 40 N 4–24m/min
100 N 1.5–10m/min
FR-40-200-Q-DL 40 mm 200 mm 185 mm 20 N 5–30m/min 41
Transverse drive 40 N 4–24m/min
100 N 1.5–10m/min
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
33
BENEFITS
Transmitted light conveyor
• Integrated transmitted light
- No shadows
- Noreflections
- Minimuminfluenceof external light
- Minimum space requirements
• Lighting intensity can be dimmed viaananaloguesignal(0–10VDC) (exceptions:FR-12-20-DLand BK-20-20-DL)
• Lighting duration can be controlled via a trigger signal (10msmax.)(exceptions: FR-12-20-DLandBK-20-20-DL)
• Simple design and easy integration into existing systems
• Easy installation
• Useofitem aluminium profiles
• Useofhigh-gradematerials: Stainless steel and aluminium
• Extra low voltage - No special safety precautions required
• Excellent serviceability: Conveyors integrated into existing automation systems can be easily disassembled
Additional BENEFITS
Internal drive
• No interference contours
Transverse drive
• Higher belt speeds
• Motor for the most part integrated into housing, external contact protection cover
• No interference contour over height
Kit
• The kit system allows our design department to rapidly implement engineered custom solutions
• State-of-the-art drive technology
- EC motor (brushless DC motor) - Integrated electronic speed controller operated via integrated foil keypad or external analogue signal 0 – 10 V DC
- Low current input at high conveying capacity
FR-12-20-DL
FR-20-40-DL
FR-40-80-Q-DL
FR-40-120-Q-DL
FR-40-160-Q-DL
FR-40-200-Q-DL
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Standard centre distances in mm
100 150 200
Max. conveyed load in N Conveyor speed m/min Supply voltage
2 1.5 Motor: 6 V DC
Anyconveyingdirection
Conveyor belt
Translucent
Belt width
17 mm
Transmitted light
Supplyvoltage/currentinput 24VDC(18–30VDC)/0.05A
Colour/colourtemperature White/5,000K
Lighting duration Continuous mode
FR-12-20-DL Transmitted light conveyor with internal drive34
Housing height 12 mm I Housing width 20 mm
Conveyor belt: Translucent
Detail: Transmitted light field
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
200
150
100
0.9
0.9
0.9
Ø12
Ø12
Ø12
190
140
90
55
55
55
64.8/114.8/164.820.4Transmitted light field
10
10
10
2xM3,4deep(bothsides)
2xM3,4deep(bothsides)
15Tr
ansm
itted
lig
ht fi
eld
17 20Ho
usin
g w
idth
Belt
wid
th
Approx.50
4-pinsocketwithflangeconnectorwithcable approx.2m(4x0.14mm2)
2xM3,4deep(bothsides)
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
BK-20-20-DL Transmitted light conveyor with internal drive 35
Housing height 20 mm I Housing width 20 mm
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Length gear motor,depends on gear ratio
97mmmin./122mmmax. 1626.5
36.5 16.5
20
End tube motor
20
17
Ø24
Rollerdiameter
25
Approx.
28
Approx.20
20.4
77
Preferred conveying direction
Centre distance
Item aluminium profile with T grooves 5 mm
Transmitted light field95 min. 130 min.
15
Standard beltapprox. 0.9 mm thick
Approx.1mmoverlap
ofmotorflangeplate
over
con
veyo
r bel
t
48
Sliding plateV2A,1.5mm
Gear motor cable approx. 2.5 m (6x0.14mm2)
4-pinsocketwithflangeconnectorwithtransmittedlightcableapprox.2m(4x0.14mm2)
65°Sliding plate width/housing width
Belt width
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
FR-20-40-DL Transmitted light conveyor with internal drive36
Housing height 20 mm I Housing width 40 mm
Standard centre distances in mm
350 400 450 500 600 700 800 900 1,000 Special centre distances on request
Max. conveyed load in N Conveyor speed m/min Supply voltage
5 2 – 8 24 V DC
15 0.7 – 3 24 V DC
Integrated speed controller
Conveyor belt
Translucent(FDA)
Belt width
32 mm
Transmitted light
Supplyvoltage/currentinput 24VDC(18–30VDC)/0.01A
Colour/colourtemperature White/5,000K
Intensity Adjustableviaananaloguesignal0–10VDC
Lighting duration
Trigger mode Proportionaltotriggerpulse/max.10ms
Continuous mode Permanent
Conveyorbelt:Translucent(FDA)
Detail: Transmitted light field
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!or
25 25
Item aluminium profile with T grooves 5 mm
* See example below for other position of the transmitted light field
Transmitted light deflectionhousing
Foil keypad for speed setting
Sliding plate V2A,1.5mm
Standard belt0.9 mm thick
4 x M4, 7 deep (bothsides)
3210 Ø2
2Be
lt w
idth
Rollerdiameter
36Sl
idin
g pl
ate
wid
th40
Hous
ing
wid
th
Cable approx. 2.5 m (10x0.14mm2)
Preferred conveying direction
Atleast30050 *
30
Transmitted light field
Centre distanceApprox.100 220
25
Approx. 30 25
Item aluminium profile with T grooves 5 mm
Foil keypad for speed setting
Sliding plate V2A,1.5mm
Standard belt1 mm thick
4 x M4, 7 deep(bothsides)
3210 Ø2
2Be
lt w
idth
Rollerdiameter
36Sl
idin
g pl
ate
wid
th40
Hous
ing
wid
th
Cable approx. 2.5 m (10x0.14mm2)
Preferred conveying direction
Atleast300Atleast100 *
30
Transmitted light field
Transmitted light housing
Centre distance100 220
* See example above for other position of the transmitted light field
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
BK-20-40-DL Transmitted light conveyor with internal drive 37
Housing height 20 mm I Housing width 40 mm
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
46.5 26.5Approx.
35
Belt width
Sliding plate width
Housing width
26.5
20
16
36
40
32
Length gear motor,depends on gear ratio97mmmin./122mmmax.
End tube motor
Gear motor cable approx. 2.5 m (6x0.14mm2)
6-pinsocketwithflangeconnector with transmitted light cable approx. 2 m (6x0.14mm2)
Preferred conveying direction
Centre distance
Ø22
Rollerdiameter
Approx.30
25 77
Standard beltapprox. 0.9 mm thick
Sliding plateV2A,1.5mm
Item aluminium profile with T grooves 5 mm
Transmitted light field
100 min. 130 min.
Both sides M4
30
Approx.1mmoverlap
ofmotorflangeplate
over
con
veyo
r bel
t
48
30
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
FR-40-80-Q-DL Transmitted light conveyor with internal drive38
Housing height 40 mm I Housing width 80 mm
Centre distances in mm
450 500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
Translucent(FDA) Others on request
Belt width
65 mm
Transmitted light
Supplyvoltage/currentinput 24VDC(18–30VDC)/0.42A
Colour/colourtemperature White/5,000K
Intensity Adjustableviaananaloguesignal0–10VDC
Lighting duration
Trigger mode Proportionaltotriggerpulse/max.10ms
Continuous mode Permanent
Conveyorbelt:Translucent(FDA)
Detail: Transmitted light field
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Standard beltapprox. 1.2 mm thick
Item aluminium profile with T grooves 5 mm
Transmitted light housing
60Transmitted light field
60Tr
ansm
itted
lig
ht fi
eld
80
Centre distance
180 min. 230 min.
Approx.80 160 130
Ø44
Rollerdiameter
Sliding plateV2A,2mm
Gear motor cable approx. 2.5m(6x0.14mm2)
Transmitted light cableapprox.2.5m(5x0.25mm2)
65
Belt
wid
th75
Slid
ing
plat
e w
idth
80Ho
usin
g w
idth
Preferred conveying direction
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
FR-40-120-Q-DL Transmitted light conveyor with internal drive 39
Housing height 40 mm I Housing width 120 mm
Centre distances in mm
450 500 600 700 800 900 1.000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
Translucent(FDA) Others on request
Belt width
105 mm
Transmitted light
Supplyvoltage/currentinput 24VDC(18–30VDC)/0.93A
Colour/colourtemperature White/5,000K
Intensity Adjustableviaananaloguesignal0–10VDC
Lighting duration
Trigger mode Proportionaltotriggerpulse/max.10ms
Continuous mode Permanent
Conveyorbelt:Translucent(FDA)
Detail: Transmitted light field
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Preferred conveying direction
180 min. 230 min.
25
Centre distance
200Approx.80 130
Ø44Rollerdiameter
Transmitted light housing
Gear motor cable approx. 2.5 m (6x0.14mm2)
Sliding plateV2A,2mm
Transmitted light cableapprox.2.5m(5x0.25mm2)
Item aluminium profile with T grooves 5 mm
Standard beltapprox. 1.2 mm thick
105
Belt
wid
th
115
Slid
ing
plat
e w
idth
120
Hous
ing
wid
th
100Transmitted light field
100
Tran
smitt
ed
light
fiel
d
40
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
FR-40-160-Q-DL Transmitted light conveyor with internal drive40
Housing height 40 mm I Housing width 160 mm
Centre distances in mm
500 600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5– 30 4 – 24 1.5 – 10 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
Translucent(FDA) Others on request
Belt width
145 mm
Transmitted light
Supplyvoltage/currentinput 24VDC(18–30VDC)/1.23A
Colour/colourtemperature White/5,000K
Intensity Adjustableviaananaloguesignal0–10VDC
Lighting duration
Trigger mode Proportionaltotriggerpulse/max.10ms
Continuous mode Permanent
Conveyorbelt:Translucent(FDA)
Detail: Transmitted light field
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Centre distance
240Approx.80 130
Ø44
Rollerdiameter
Transmitted light housing
Gear motor cable approx. 2.5 m (6x0.14mm2)
Transmitted light cableapprox.2.5m(5x0.25mm2)
Sliding plateV2A,2mm
Item aluminium profile with T grooves 5 mm
Standard beltapprox. 1.2 mm thick
145
Belt
wid
th
155
Slid
ing
plat
e w
idth
160
Hous
ing
wid
th
140Transmitted light field
140
Tran
smitt
ed li
ght fi
eld
25
Preferred conveying direction
220 min. 270 min.
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
FR-40-200-Q-DL Transmitted light conveyor with internal drive 41
Housing height 40 mm I Housing width 200 mm
Centre distances in mm
600 700 800 900 1,000 1,200 1,400 1,600 Special centre distances on request
Speed in m/min (controlledviaanaloguesignal0–10VDC)
Programmed, fixed value / analogue signal 0 V DC
24 19 8 Others on request
Standstill / analogue signal 0.5 – 0.9 V DC
0 0 0
Controllable / analogue signal 1 – 10 V DC
5 – 30 4 – 24 1.5 – 10 Optional: External Vetter reference value unitVSW-11orVR-24-SW-11
Max. conveyed load in N Conveyor speed m/min Supply voltage
20 5 – 30 24 V DC
40 4 – 24 24 V DC
100 1.5 – 10 24 V DC
Conveyor belt
Translucent(FDA) Others on request
Belt width
185 mm
Transmitted light
Supplyvoltage/currentinput 24VDC(18–30VDC)/1.68A
Colour/colourtemperature White/5,000K
Intensity Adjustableviaananaloguesignal0–10VDC
Lighting duration
Trigger mode Proportionaltotriggerpulse/max.10ms
Continuous mode Permanent
Conveyorbelt:Translucent(FDA)
Detail: Transmitted light field
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Selection required!
or
or
Gear motor cable approx. 2.5 m (6x0.14mm2)
Transmitted light cableapprox.2.5m(5x0.25mm2)
Centre distance280Approx.80 130
Ø44
Rollerdiameter
Transmitted light housing
Sliding plateV2A,2mm
Item aluminium profile with T grooves 5 mm
Standard beltapprox. 1.2 mm thick
Preferred conveying direction
240 min. 290 min.
185
Belt
wid
th
195
Slid
ing
plat
e w
idth
200
Hous
ing
wid
th
180Transmitted light field
180
Tran
smitt
ed li
ght fi
eld
25
Max. speed +
SpeedVetter unit for reference speed
Industry standard
AnaloguevoltageV(UnRef)
Max. speed
Programmed, fixed speed
Fixed speed
Speed0
Speedmin. – max.
You specify, we configure
Let us know your automation task.
We select the optimum Vetter standard components from our kit system and
configure the ideal product for your application. During the configuration
phase, our design department is in close contact with you. This way, we ensure
that all requirements and constraints are considered and that you receive your
quotation as quickly as possible. Together with the quotation, we provide all
technical data and a 3D model so that you know exactly what you will get.
Bytheway:AllVetterstandardcomponentsareavailabledirectlyexwarehouse–
you can look forward to fast delivery.
Custom solutions beyond the kit system
Our kit system does not provide exactly the solution you are looking for?
No problem.We are your competent partner if your specific application requires a solution
that cannot be directly created using our kit system.
Just get in touch with us.
Kit and custom solutions42
OVERVIEW kitConveyor type Profile height Profile width Belt width Page
BK-20-20 20 mm 20 mm 15 mm 44
(single-track)
BK-20-20-x-2 20 mm 20 mm 15 mm 44
(dual-track)
BK-20-40 20 mm 40 mm 32 mm 45
(single-track)
BK-20-40-x-2 20 mm 40 mm 32 mm 45
(dual-track)
BK-30-60 30 mm 60 mm 50 mm 46
OVERVIEW custom solutionsConveyor type Page
Knife edgesEncoder shaftsLateral guides/U-shaped groovesShaft stubSpecial conveyor belts
48 – 49
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Different examples
BK-20-Inkjet
BK-20-20-120-2
BK-20-20
BK-20-20
43
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
BENEFITS
Kit and custom solutions
• Perfectly tuned to your application by means of optimum selection and combination of the components
• Single-track and multiple-track small conveyors possible
• To simplify your design process, we provide 3D models for each custom solution
• Large selection of conveyor belts (flat belts and round belts)
• Integration of transmitted light units possible for profile widths 20 and 40 mm
• Useofknifeedges(rollerdia- meters5mmand8mm) possible
• Useofitem aluminium profiles
• Useofhigh-gradematerials: Stainless steel and aluminium
• 24 V extra low voltage
- No special safety precautions required
• State-of-the-art drive technology - EC motor (brushless DC motor) - Integrated electronic speed controller operated via external analogue signal 0 – 10 V DC
- Low current input at high conveying capacity
Additional BENEFITS kit
Kit
•Kit system allows for simple and fast implementation of custom solutions together with our design department
Custom solutions
•You benefit from our comprehensive know-how in the area of conveying technology and from years of experience in engineering custom solutions
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
BK-20-20 Kit
BK-20-20-x-2 Kit
44
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Preferred conveying direction
Centre distance36.5 16.5
20
20
26.5
Length gear motor,depends on gear ratio
97mmmin./122mmmax.
15
16
Housing widthSliding plate widthBelt width 25 77
Item aluminium profile with T grooves 5 mm
Ø24
48Approx.1mmoverlap
ofmotorflangeplate
over
con
veyo
r bel
t
Rollerdiameter
Sliding platealuminium 2 mm
End tube motor
Cable approx. 2.5 m (6x0.14mm2)
Standard beltapprox. 1.6 mm thick
36.5 Track width
25 77
Usableclearance
Housing width
Belt width
Housing widthSliding plate width
16.5
16
20
15
Preferred conveying direction
Centre distance
48Approx.1mmoverlap
conv
eyor
bel
t to
the
motorflangeplate
Length gear motor,depends on gear ratio97mmmin./122mmmax.
Distance pieces item aluminium profile with T grooves 5 mm
Drive shaft Ø8
End tube motor
Cable approx. 2.5 m (6x0.14mm2)
Item aluminium profile with T grooves 5 mm
Ø24
Rollerdiameter
Standard beltapprox. 1.6 mm thick
Sliding platealuminium 2 mm
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
BK-20-40 Kit
BK-20-40-x-2 Kit
45
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
1626.5
Length gear motor,depends on gear ratio97mmmin./122mmmax.
Ø22
10Rollerdiameter
Sliding plateV2A,1.5mm
46.5 26.5
40
36 Approx.3025 7732
20
Housing width
Sliding plate width
Belt width
Standard beltapprox. 0.8 mm thick
Preferred conveying direction
Centre distance
Item aluminium profile with T grooves 5 mm
48Approx.1mmoverlap
ofmotorflangeplateover
conv
eyor
bel
t
End tube motor
Cable approx. 2.5 m (6x0.14mm2)
4 x M4, 7 deep(bothsides)
Sliding plateV2A,1.5mm
Standard beltapprox. 0.8 mm thick
Preferred conveying direction
Centre distance
4 x M4, 7 deep(bothsides)
46.5 Track width
Usableclearance
Housing width
Belt width
Sliding plate width
Housing width
26.5
16
36
40
32
Length gear motor,depends on gear ratio
113mmmin./144mmmax.
Distance pieces item aluminium profile with T grooves 5 mm
Drive shaft Ø8
End tube motor
Cable approx. 2.5 m (6x0.14mm2)
Ø22
10
Rollerdiameter
Approx.30
25 77
64
Item aluminium profile with T grooves 5 mm
Approx.1mmoverlap
ofmotorflangeplateover
conv
eyor
bel
t
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
BK-30-60 Kit46
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Length gear motor,depends on gear ratio
138mmmin./169mmmax. 1626.5
20
56.5 36.5
60Approx.
30
Housing width
Belt width50
Preferred conveying direction
Centre distance
Item aluminium profile with T grooves 6 mm
Ø30
Rollerdiameter
Standard beltapprox. 1.3 mm thick
77
64Approx.1mmoverlap
conv
eyor
bel
t to
the
motorflangeplate
End tube motor
Cable approx. 2.5 m (6x0.14mm2)
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Kit 47
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
BK-20-40-1 with top-mounted motor
BK-20-20-130
BK-20-20-2 for conveying solar cells
BK-20-20-1 with high-torque motor
Knifeedges(option)
BK-20-54-2 with special intermediate pieces
BK-20-20-1 with integrated lateral guides
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Custom solutions48
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
BK-20-40-3 as vacuum belt
FR-40-120asvacuumbelt
ZR-40-80withpartcarriers
BK-20-200withspecialmotorflangeplate
BK-20-20-2 for ink jet labelling from the bottom
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Custom solutions 49
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
BK-20-40-3 with special sliding plate
BK-20-20-3 with integrated lateral guides
BK-20-20-2-RRwithroundbelts
Solar cell handling with “sponge type conveyor belt”
BK-20-20-3 with integrated lateral guides
Conveyor belts
OVERVIEWPage
Pictures of examples 52 – 53
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
50
BENEFITS
Conveyor belts
The versatility of Vetter small conveyors is matched by the versatile selection of conveyor belts:
• Varioustypessuchasflatbelts, timing belts, round belts, etc.
• Different colours, materials and surfaces all the way to transmitted light applications for image processing
Whether you want to operate your system in accumulating mode, require outstanding friction grip or even need a “mixed mode” – we provide you with exactly the solution you need for your application. Our timing belts even allow you to screw-mount your part carriers.
Andofcourse,ourconveyorbeltsofferalltheflexibilityrequiredforyourapplication.
We can equip your belt with
- Cleats
- Carriers
-Longitudinal/transverseprofiles
in numerous sizes, shapes and colours.
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
51
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Conveyor belts52
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
FR-40-80-Q-Pwithnubtopconveyorbelt
FR-40-80withcrossbars
FR-40-120withT-20cleats
FR-40-80withLinatexlongitudinalandtransverseprofiles
Conveyor belt with ground longitudinal groove
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Conveyor belts 53
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
FR-40-120withT-20cleatsandintegratedlateralguide
BK-20-20-1 with special carriers
FR-40-200withstainlesssteelconveyorbelt
Vacuum belt
FR-30-60withtransversalprofilesandspecial-widthconveyorbelt
BK-20-20-1 with timing belt and special carriers
Conveyor belt “Supergrip”
Controllers54
OVERVIEWReference value unitType
Input voltage Reference value output
Output voltage /current
Conveyor speed Page
VSW-11 24 V DC 0 – 11 V DC – 0 – 110 % 56
VR-24-SW-11 100–240VAC/ 0 – 11 V DC 24VDC/2A 0 – 110 % 57
50–60Hz/1.3A
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
55
BENEFITS
Controllers
•ReferencespeedfortheEC motors(brushlessDCmotors) of Faulhaber types 2232-BX4-SC, 2250-BX4-SC, 3242-BX4-SC and 3268-BX4-SC via integrated speed controller
• Flexibly controllable speed of the conveyor to up to 110 % of the nominal speed
• Flexibly adjustable lighting intensity for the Vetter transmitted lightunits(notforsizes12-20 and20-20).
Additional BENEFITS
Controller VSW-11
• Connection assignment optimized for Vetter small conveyors
• Easy installation in control cabinets
• Easy integration into existing systems
Controller VR-24-SW-11
• Easy wall or table mounting
• Degree of protection IP 67
• Connection via connectors (housingdoesnotneedto beopened)
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
VSW-11
VR-24-SW-11
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Input voltage
24 V DC
Reference value output
0–11VDC(adjustableviarotarypotentiometer)
Control of conveyor speed
0 % – 110 %
Application / compatibility
ReferencespeedfortheECmotors(brushlessDCmotors)ofFaulhabertypes2232-BX4-SC,2250-BX4-SC,3242-BX4-SCand3268-BX4-SCviaintegratedspeedcontroller(notsuitableforbrushedmotors).Lightingintensityofthetransmittedlightunitscanbecontrolled(notforsizes12-20and20-20).
VSW-11 Reference value unit56
VSW-11
VSW-11 installed in control cabinet
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Approx.100
Approx.65
Approx.23
©VetterKleinförderbänderGmbH/Einsteinstraße8/D-89179BeimerstettenTel.+49-7348-967485-0/[email protected]/www.vetter-band.de
© Vetter Kleinförderbänder GmbHProductcatalogue/Version08.2017/Wereservetherighttomodifications.
Input voltage
100–240VAC/50–60Hz/1.3A
Output voltage
24 V DC
Maximum continuous output current
2A
Reference value output
0–11VDC(adjustableviafoilkeypad)
Control of conveyor speed
0 % – 110 %
Application / compatibility
ReferencespeedfortheECmotors(brushlessDCmotors)ofFaulhabertypes2232-BX4-SC,2250-BX4-SC,3242-BX4-SCand3268-BX4-SCviaintegratedspeedcontroller(notsuitableforbrushedmotors).Lightingintensityofthetransmittedlightunitscanbecontrolled(notforsizes12-20and20-20).
VR-24-SW-11 Reference value unit with voltage supply 57
VR-24-SW-11
Inte
rnal
driv
eTr
ansv
erse
driv
eCe
ntre
driv
eTr
ansm
itted
ligh
tKi
t and
cu
stom
sol
utio
nsCo
nvey
or b
elts
Cont
rolle
rs
Approx. 125108
A-A(1:2)Screw mounting possible
A A
Approx
. 60
Approx
. 200
Approx
. 150
127
Ø4.25
International offices
58
Belgium
BCK Holland B.V.AndréHuijgenTel.: +31 416 673880Fax: +31 416 673888Email: [email protected] Web: www.bckholland.com
PEC products n.v. Gerrit Taverniers Tel.: +3216/39.83.55Fax: +3216/39.83.69Email: [email protected] Web: www.pec.be
Denmark
KPConveyorsApSKurt PaulsenKløverlykke 78DK-6470 SydalsTel.: +45 20 30 53 [email protected]
France
Binder MagneticClaude Pernin Tel: +33 1 4613 8080Fax: +33 1 4613 8099Email: [email protected]: www.binder-magnetic.com
Great Britain
AllSolutionProductsLtdStuart SaundersTel.: +44 1256 893 863 oder +44 7793 025 070Fax: +44 1256 895 274Email: [email protected] Web: www.allsolutionproducts.com
The Netherlands
BCK Holland B.V.AndréHuijgenTel.: +31 416 673880Fax: +31 416 673888Email: [email protected] Web: www.bckholland.com
Austria
Haberkorn GmbHAndreasLiebmingerTel.: +43 316 287082 - 0Fax: +43 316 287 82 - 99Email: [email protected]: www.haberkorn.com
Sweden
EasySystemsSvenskaABAndersSkjöldTel.: +46 10 209 33 10Email: [email protected] Web: www.easysystems.se
Spain
SinergesTecmon,S.A.JordiDarder/AndreuSelvaTel.: +34 93 6633500 Fax: +34 93 6633501Email: [email protected] Web: www.sinerges.com
59
The Netherlands
BCK Holland B.V.AndréHuijgenTel.: +31 416 673880Fax: +31 416 673888Email: [email protected] Web: www.bckholland.com
Austria
Haberkorn GmbHAndreasLiebmingerTel.: +43 316 287082 - 0Fax: +43 316 287 82 - 99Email: [email protected]: www.haberkorn.com
Sweden
EasySystemsSvenskaABAndersSkjöldTel.: +46 10 209 33 10Email: [email protected] Web: www.easysystems.se
Spain
SinergesTecmon,S.A.JordiDarder/AndreuSelvaTel.: +34 93 6633500 Fax: +34 93 6633501Email: [email protected] Web: www.sinerges.com
Notes
Vetter Kleinförderbänder GmbHEinsteinstraße 8D-89179 Beimerstetten
Tel.: +49-7348-967485-0Fax: +49-7348-967485-99Email: [email protected]: www.vetter-band.de