Pre Emphasis
-
Upload
jagadeesh-kumar -
Category
Documents
-
view
224 -
download
0
Transcript of Pre Emphasis
-
8/12/2019 Pre Emphasis
1/57
MADANAPALLE INSTITUTE OF TECHNOLOGY & SCIENCE
MADANAPALLI
ANGALLU, MADANAPALLE517 325
ANALOG AND DIGITAL COMMUNICATIONS
LABORATORY MANUAL
DEPARTMENT
OF
ELECTRONICS & COMMUNICATION ENGINEERING2012-13
-
8/12/2019 Pre Emphasis
2/57
MADANAPALLE INSTITUTE OF TECHNOLOGY &SCIENCE,Department of ECE
ANALOG & DIGITAL COMMUNICATIONS
LAB MANUAL
Prepared By
Mr. P.R.RATNA RAJU.K, M.Tech, Asst. ProfessorDepartment of ECE,
MITS, Madanapalle
-
8/12/2019 Pre Emphasis
3/57
3| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 3
JAWAHARLAL NEHRU
TECHNOLOGICAL UNIVERSITY ANANTAPUR
Electronics and Communication Engineering
(9A04607) ANALOG & DIGITAL COMMUNICATIONS LAB
B.Tech III-II Sem. (E.C.E.) T P C
0 3 2Minimum Twelve Experiments to be conducted: (Six from each part A & B)
Part A (Analog Communication Lab):
1 Amplitude modulation and demodulation.2 Frequency modulation and demodulation.3 Characteristics of Mixer.4 Pre-emphasis & de-emphasis.5 Pulse Amplitude Modulation and demodulation.6 Pulse Width Modulation and demodulation.7 Pulse Position Modulation and demodulation.8 Radio Receiver measurementsSensitivity, Selectivity, & Fidelity.Part B (Digital Communication Lab):
1 Sampling Theoremverification.2 Time division multiplexing.3 Pulse Code Modulation.4 Delta modulation.5 Frequency shift keying - Modulation and Demodulation.6 Phase shift keying - Modulation and Demodulation.7 Differential phase shift keying - Modulation and Demodulation.8 QPSK - Modulation and Demodulation.Equipment required for Laboratories:
1 RPS - 030 V2 CRO - 020 M Hz.3 Function Generators - 01 M Hz4 RF Generators - 01000 M Hz. /0100 M Hz.5 Multimeters6 Lab Experimental kits for Communication7 Components8 Radio Receiver/TV Receiver Demo kits or Trainees
-
8/12/2019 Pre Emphasis
4/57
4| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 4
MADANAPALLE INSTITUTE OF TECHNOLOGY AND SCIENCE,
MADANAPALLEDEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
ANALOG & DIGITAL COMMUNICATIONS LABORATORY
LIST OF EXPERIMENTS
Part A (Analog Communication Lab):
1. Amplitude Modulation and Demodulation.2. Frequency Modulation and Demodulation.3. Characteristics of Mixer.4. Pre-Emphasis & De-Emphasis.5. Pulse Amplitude Modulation and Demodulation.6. Pulse Width Modulation and Demodulation.7. Pulse Position Modulation and demodulation.8. Radio Receiver measurementsSensitivity, Selectivity, & Fidelity.
Part B (Digital Communication Lab):
1. Sampling Theoremverification.2. Time division multiplexing.3. Pulse Code Modulation.4. Delta modulation.5. Frequency shift keying - Modulation and Demodulation.6. Phase shift keying - Modulation and Demodulation.7. Differential phase shift keying - Modulation and Demodulation.8. QPSK - Modulation and Demodulation.
ADDITIONAL EXPERIMENTS
1. Synchronous Detector.2. Differential Phase shift Keying.
ADVANCED EXPERIMENTS
1. Implementing Convolutional Encoder/Decoder using MATLAB.2. Implementing Viterbi Algorithm using MATLAB.
Mr. P R Ratna Raju.K & Mr. D Balakrishna Reddy Dr A.R.Reddy
Faculty In-Charge Head of the Department
-
8/12/2019 Pre Emphasis
5/57
5| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 5
EXP.NO DATE Experiment Name Page No Remarks
1
2
3
4
5
6
7
8
9
10
11
12
-
8/12/2019 Pre Emphasis
6/57
6| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 6
1. Amplitude Modulation & Demodulation
Aim: 1. To generate amplitude modulated wave and determine the percentage
modulation.
2. To Demodulate the modulated wave using envelope detector.
Apparatus Required:
1. Amplitude Modulation and Demodulation Trainer2. Function Generator
3. Oscilloscope
4. Connecting Wires
Circuit Diagram For modulation:
Fig 1: CIRCUIT FOR AMPLITUDE MODULATION
Circuit Diagram For Demodulation:
Fig 2: CIRCUIT FOR AM DEMODULATOR
-
8/12/2019 Pre Emphasis
7/57
7| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 7
Fig 3: Carrier Generator
Theory:
Modulation is defined as the process by which some characteristics of a carrier
signal is varied in accordance with a modulating signal. The base band signal is referred
to as the modulating signal and the output of the modulation process is called as the
modulation signal.Amplitude modulation is defined as the process in which is the amplitude of the
carrier wave is varied about a means values linearly with the base band signal. The
envelope of the modulating wave has the same shape as the base band signal provided the
following two requirements are satisfied
(1). the carrier frequency fc must be much greater then the highest frequency components
fm of the message signal m (t)
i.e. fc >> fm
(2) The modulation index must be less than unity. if the modulation index is greater than
unity, the carrier wave becomes over modulated
Procedure:
1Switch on the trainer and check the O/P of carrier generator on oscilloscope.2. Connect 1KHz with 2 Volts A.F signal at AF I/P to the modulator circuit.
3. Connect the carrier signal at carrier I/P of modulator circuit.
-
8/12/2019 Pre Emphasis
8/57
8| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 8
4. Observe the modulator output signal at AM O/P Spring by making necessary changes
in A.F. signal.
5. Vary the modulating frequency and amplitude and observe the effects on the
modulated waveform.
6. The depth of modulation can be varied using the variable knob (potentiometer)provided at A.F. input.
7. The percentage of modulation or modulation factor can be calculated using the
following formulas.
8. Find the value of R from fm=1/(2*Pi*R*C) , C=0.1F
9. Connect the circuit diagram as shown in Fig.2.
10. Feed the AM wave to the demodulator circuit and observe the output
11. Note down frequency and amplitude of the demodulated output waveform.
12. Draw the demodulated wave form., m=1
Tabular Column:
S. No Modulator O/P Demodulator O/P
Fm
(Hz)
Vm
(V)
Vmax
(V)
Vmin
(V)
m
Fo
(Hz)
V0
(V)
-
8/12/2019 Pre Emphasis
9/57
9| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 9
-
8/12/2019 Pre Emphasis
10/57
10| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 10
-
8/12/2019 Pre Emphasis
11/57
11| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 11
PRECAUTIONS:
1. Connect the circuit as shown in the circuit diagram.
2. Apply the required voltages wherever needed.3. Do not apply stress on the components.
Result:
-
8/12/2019 Pre Emphasis
12/57
12| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 12
2. Frequency Modulation & Demodulation
Aim: 1. To generate frequency modulated signal and determine the modulation index and
bandwidth for various values of amplitude and frequency of modulating signal.
2. To demodulate a Frequency Modulated signal using FM detector.
Apparatus required:
1. Amplitude Modulation and Demodulation Trainer
2. Function Generator3. Oscilloscope
4. Connecting Wires
Theory:
The process, in which the frequency of the carrier is varied in accordance with the
instantaneous amplitude of the modulating signal, is called Frequency Modulation. TheFM signal is expressed as
WhereAcis amplitude of the carrier signal, f c is the carrier frequency is themodulation index of the FM wave
Circuit Diagram:
-
8/12/2019 Pre Emphasis
13/57
13| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 13
Fig 1: Circuit Diagram for Frequency Modulator
Fig 2 : Circuit for Frequncy Demodulator
PROCEDURE:
1. Switch on the FM experimental board.
2. Connect Oscilloscope to the FM O/P and observe that carrier frequency at that point
without any A.F. input.
3. Connect around 7KHz sine wave (A.F. signal) to the input of the frequency modulator
(At AF input).
4. Now observe the frequency modulation output on the 1st channel of on CRO and
adjust the amplitude of the AF signal to get clear frequency modulated wave form.
5. Vary the modulating frequency (A.F Signal) and amplitude and observe the effects on
the modulated waveform.
6. Connect the FM o/p to the FM i/p of De-modulator.
7. Vary the potentiometer provided in the demodulator section.
8. Observe the output at demodulation o/p on second channel of CRO.
9.Draw the demodulated wave form
-
8/12/2019 Pre Emphasis
14/57
14| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 14
Tabular Column:
Vc= , Fc= ,Vm=
Sl
No
Fm(KHz)
Tmax(sec) Tmin(sec) Fmax(KHZ)
Fmin(KHZ)
F
(KHZ)
B.W
(KHZ)
Demod
Vo
(V)
PRECAUTIONS:1. Connect the circuit properly.2. Apply the required voltages wherever needed.
3. Do not apply stress on the components.
Result:
-
8/12/2019 Pre Emphasis
15/57
15| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 15
-
8/12/2019 Pre Emphasis
16/57
16| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 16
3. Characteristics of Mixer
Aim: To observe the characteristics of a Frequency Mixer and to measure its conversion
gain..
Apparatus Required:
1. Frequency mixer trainer kit.
2. Function generator - (2)3. C R O
4. B N C Probes
Theory:
The mixer is a nonlinear device having two sets of input terminals and one set of
output terminals. Mixer will have several frequencies present in its output, including the
difference between the two input frequencies and other harmonic components
Circuit Diagram:
Fig 1: Mixer Circuit Diagram
PROCEDURE :
1. Connect the circuit as shown in the circuit diagram.
2. Apply 99 kHz signal to the base of the transistor and 100 kHz, signal to the emitter of
the transistor.
3. Observe a sinusoidal signal with 1kHz frequency across output terminals.
-
8/12/2019 Pre Emphasis
17/57
17| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 17
4. Vary Base signal frequency and note down O/P amplitude. The output reaches to a
maximum value at a particular frequency. Calculate conversion gain.
Conversion gain = (O/P Voltage)/ (Base signal voltage)
5. Plot conversion gain vs base signal frequency,
Sample readings:
S.No Fx
(KHz)
Fy
(KHz)
Vx
(V)
Vy
(V)
Fo
(KHz)
Output
voltage(V)
Gain(dB)
PRECAUTIONS:
1. Connect the circuit properly.
2. Apply the required voltages wherever needed.
3. Do not apply stress on the components.
Result:
-
8/12/2019 Pre Emphasis
18/57
18| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 18
4. Pre-Emphasis & De-Emphasis
Aim:
I) To observe the effects of pre-emphasis on given input signal.
ii) To observe the effects of De-emphasis on given input signal.
Apparatus Required:1. Resistors (10 K-2, 47K, 75K,1K)
2. Capacitors (22F, 0.1-2,)
3. Transistor BC107
4 Function generators
5. CRO
6. Connecting Wires
7.RPS (15V)
8. Connecting wires.
Theory:
The noise has a effect on the higher modulating frequencies than on the lower
ones. Thus, if the higher frequencies were artificially boosted at the transmitter and
correspondingly cut at the receiver, an improvement in noise immunity could be
expected, thereby increasing the SNR ratio. This boosting of the higher modulating
frequencies at the transmitter is known as pre-emphasis and the compensation at the
receiver is called de-emphasis
Circuit Diagrams:
Pre-Emphasis:
-
8/12/2019 Pre Emphasis
19/57
-
8/12/2019 Pre Emphasis
20/57
20| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 20
Table2: de-emphasis Vi = 5V
S.No Frequency
(KHz)
Output voltage
(V)
Gain (dB)
1.
2.
3.
4.
5.
6.
MODEL GRAPH
1
Result:
-
8/12/2019 Pre Emphasis
21/57
21| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 21
5. Pulse Amplitude and Modulation
Aim:To generate the Pulse Amplitude modulated signal and demodulated signals.
Apparatus required:
1.Pulse amplitude modulation trainer.
2. Signal generator
3. CRO
4. BNC probes, connecting wires.
Theory:
PAM is the simplest form of the data modulation. The amplitude of uniformly
spaced pulses is varied in proportion to the corresponding sample values of a continuousmessage m(t).
A PAM waveform consists of a sequence of list-topped pulses. The amplitude of
each pulse corresponds to the value of the message signal x(t) at the leading edge of thepulse.
The pulse amplitude modulation is the process in which the amplitude of
regularity spaced rectangular pulses vary with the instantaneous sample values of acontinuous message signal in a one-one fashion.
PAM is of two types :
1. Double polarity PAMThis is the PAM wave which consists of both positive andnegative pulses.
2. Single polarity PAMThis consists of PAM wave of only either negative orpositive pulses. In this the fixed dc level added to the signal to ensure single
polarity signal.
-
8/12/2019 Pre Emphasis
22/57
22| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 22
Circuit
Diagram:
-
8/12/2019 Pre Emphasis
23/57
23| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 23
Procedure:
1 . Switch on pulse Amplitude modulation and demodulation trainer.
2 . In clock generator section connect pin 6 of 555IC to the 33pfcapacitor terminal.
3 . Check the clock generator (RF)output signal.
4 . Connect RF output of clock generator to the RF input of modulator section.
5 . Connect a 1KHz; 2vp-p of sine wave from function generator to the AF input of
modulator section.
6 . Short the 10F terminal and 10k terminal of modulator.
7 . Connect 10k terminal to pin 1 of IC 4016.
8 . Connect the CRO to modulated output of modulator section.
9 . Adjust the 1k potentiometer to vary the amplitude of the modulated signal.
10. Adjust the AF signal frequency from 1KHZ-10KHZ to get stable output waveform.
While increases the AF signal frequency decreases the output signal pulses.
11 During demodulation, connect the modulated output to the PAM input of
Demodulator section.
12 . Connect channel 1 of CRO to modulating signal and channel-2 to demodulated
output. Observe the two waveforms that they are 1800out of phase, since the transistor
detector operates in CE configuration.
Sample Readings:
RF frequency = RF Voltage =
S. No AF input voltageVp-p(volts)
RF VoltageVp-p (volts)
PAM output voltage
Vmax(volts) Vmin (volts)
-
8/12/2019 Pre Emphasis
24/57
24| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 24
Expected Waveforms:
Result:
-
8/12/2019 Pre Emphasis
25/57
25| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 25
6. PULSE WIDTH MODULATION AND DEMODULATION
Aim:To generate the pulse width modulated and demodulated signals
Apparatus required:
1. Pulse width modulation and Demodulation Trainer.
2. CRO
3. BNC probes and Connecting Wires
Theory:
In PWM, the samples of the message signal are used to vary the duration of the
individual pulses. Width may be varied by varying the time of occurrence of leading
edge, the trailing edge or both the edges of the pulse in accordance with modulating
wave. It is also called Pulse Duration Modulation.
-
8/12/2019 Pre Emphasis
26/57
26| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 26
-
8/12/2019 Pre Emphasis
27/57
27| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 27
Procedure:
1 . Switch on pulse width modulation and Demodulation trainer .
2 . Connect the Clk O/P to the clk I/P terminal of PWM modulation.
3 . Connect the AF O/P to AF I/P terminal of PWM modulation.4 . Observe the PWM O/P at pin 3 of 555 IC on CRO.
5. By varying frequency and amplitude of the modulating signal, observe the
corresponding change in the width of the output pulses.
6 . During demodulation, connect the PWM O/P of PWM modulation to the PWM I/P of
PWM demodulation.
7 . Observe the demodulated output at AF O/P of PWM demodulation on CRO.
Observations:
S.No Control Voltage(V) o/p pulse width (msec)
-
8/12/2019 Pre Emphasis
28/57
28| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 28
Expected Wave forms:
Result:
-
8/12/2019 Pre Emphasis
29/57
29| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 29
7. Pulse Position Modulation & Demodulation
Aim:To generate pulse position modulation and demodulation signals and to study the
effect of amplitude of the modulating signal on output.
Apparatus required:1. Pulse position modulation and demodulation trainer.
2. CRO
3. BNC probes and Connecting Wires
Theory:
In Pulse Position Modulation, both the pulse amplitude and pulse duration areheld constant but the position of the pulse is varied in proportional to the sampled values
of the message signal. Pulse time modulation is a class of signaling technique that
encodes the sample values of an analog signal on to the time axis of a digital signal and it
is analogous to angle modulation techniques. The two main types PTM are PWM andPPM. In PPM the analog sample value determines the position of a narrow pulse relative
to the clocking time. In PPM rise time of pulse decides the channel bandwidth. It has low
noise interference.
Circuit Diagram:
-
8/12/2019 Pre Emphasis
30/57
-
8/12/2019 Pre Emphasis
31/57
31| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 31
Observations:
Modulating
Signal
Amplitude(Vp-p)
Time Period (ms) Total Time
Period(ms)Pulse Width
ON (ms)
Pulse Width
OFF(ms)
Result:
-
8/12/2019 Pre Emphasis
32/57
32| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 32
8. Sampling TheoremVerification
Aim:To study and verify the sampling theorem and reconstruction of sampled wave
form.
Apparatus Required:1. PHYSITECHs Sampling Theorem Trainer Kit
2. Function Generator
3. CRO
4. Connecting wires.
5. BNC Probes.
Theory:
The analog signal can be converted into a discrete time signal by a process calledsampling. The sampling theorem for a band limited signal of a finite energy can be stated
asA band limited signal of finite energy which has no frequency component higher
than W Hz is completely described by specifying the values of the signal at instants of
time separated by 1/2W seconds.It can be recovered from the knowledge of the samples taken at the rate of 2W per
second.
Circuit Diagram:
-
8/12/2019 Pre Emphasis
33/57
33| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 33
Procedure:
1 . Connections are made as per the Circuit diagram.
2 . Apply the input signal with a frequency of 500Hz (VP-P) using a function generator.
3 . Sampling clock frequency which is variable of 3KHz to 50KHz should be connected
across the terminals which is indicated.
4 . Now observe the sampling output of the circuit at the o/p.
5 . By using the capacitors provided on the trainer, reconstruct the signal and verify it
with the given input.
6 . Reconstructed signal voltage will be depends on capacitor value.
7 . Vary the sampling frequency and study the change in reconstructed signal.
8 . If the sampling clock frequency is below 20KHz you will observe the distorted
demodulated output.
Observations:
S. No Cases Message signal frequency
(fm KHz)
Smpling frequency
(fs KHz)
Inference
-
8/12/2019 Pre Emphasis
34/57
34| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 34
Result:
-
8/12/2019 Pre Emphasis
35/57
35| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 35
9 DELTA MODULATION & DEMODULATION
Aim: To study the Delta modulation process by comparing the present signal with the
previous signal of the given modulating signal.
APPARATUS:
1. Delta Modulation trainer
2. CRO
3. Connecting wires.
Theory:
DM uses a single bit PCM code to achieve to achieve digital transmission of
analog signal. With conventional PCM each code is binary representation of both sign
and magnitude of a particular sample. With DM, rather than transmitting a codedrepresentation of a sample a single bit is transmitted, which indicates whether the sample
is smaller or larger than the previous sample. The algorithm for a delta modulation system
is a simple one. If the current sample is smaller than the previous sample then logic 0 is
transmitted or logic 1 is transmitted if the current sample is larger than the previous
sample. The input analog is sampled and converted to a PAM signal followed by
comparing it with the output of the DAC. The output of the DAC is equal to the
regenerated magnitude of the previous sample which was stored in the up/down counter
as a binary number. The up/down counter is incremented or decremented whether the
previous sample is larger or smaller than the current sample. The up/down counter is
clocked at a rate equal to the sample rate. So, the up/down counter is updated after each
comparison.
Procedure:
1. Switch on the experimental board
2. Connect the clock signal of Bit clock generator to the bit clock input of Delta
modulator circuit.
3. Connect modulating signal of the modulating signal generator to the modulating signal
input of the Delta modulator.
4. Observe the modulating signal on Channel 1 of CRO
5. Observe the Delta modulator output on channel 2 of CRO
6. Connect the DM o/p of modulator to the DM I/P of Demodulator circuit.
-
8/12/2019 Pre Emphasis
36/57
36| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 36
7. Connect the clock signal to the Bit clock I/P of Demodulator circuit.
8. Observe the demodulated o/p on channel 2 of CRO.
9. Connect the demodulated o/p to the filter input of demodulator circuit.
10. Observe the demodulated o/p with filter on CRO.
Observations:
S. No Waves Amplitude(volts v p-
p)
Frequency ( Hz)
-
8/12/2019 Pre Emphasis
37/57
37| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 37
-
8/12/2019 Pre Emphasis
38/57
38| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 38
Result:
-
8/12/2019 Pre Emphasis
39/57
39| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 39
10. FREQUENCY SHIFT KEYING
Aim: To study frequency shift key (FSK) Modulator and Demodulator
Apparatus :
1 . FSK Modulator-FSK Demodulator.
2 . Function Generator.
3. CRO.
4 . BNC Probes.
Theory:In this method, the binary signal u (t) is used to generate a waveform.
V FSK (t) = A Cos (Wo U) t
The pulse sign is applied when v (t) = +V and minus sign is applied when V (t) =- V.Thus the frequency of transmitted signal is high for 1 and low for a 0. A straight forward
way to detect an FSK signal is to use a suitable filter of sharp cut-off.
PROCEDURE :
1 . Connect the output of the carrier o/p provided on kit to the input of carrier i/p1
terminal.
2 .Also connect one of the data output to the data input terminal provided on kit.
3. connect sin wave of certain frequency to the carrier i/p2 terminal.
4. switch ON function generator and FSK modulation and demodulation Kit.
5. Observe the FSK o/p by connecting it to CRO. Thus FSK modulation can be achieved.
6.For FSK demodulation, connect FSK o/p terminal to the FSK i/p terminal of
demodulator.
7.Observe the demodulated wave at demodulated o/p terminal by connecting it to CRO.
Model Waveforms:
-
8/12/2019 Pre Emphasis
40/57
-
8/12/2019 Pre Emphasis
41/57
41| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 41
Result:
-
8/12/2019 Pre Emphasis
42/57
42| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 42
11. PSK MODULATION& DEMODULATIONAIM:
To study the various steps involved in generating the phase shift keyed signal at the
modulator end and recovering the binary signal from the received PSK signal.
Apparatus:
1. PSK Modulation & Demodulation
2. CRO
3. Connecting Wires
Theory:
If the carrier phase is shifted between two values then the method is called Phase
Shift keying (PSK). In PSK the amplitude of the carrier remains constant.
To generate a binary PSK signal, we have to represent the input binary sequence
in polar form with symbols 1 and 0 represented by constant amplitude levels of +E band -E b, respectively. This signal transmission encoding is performed by a polar nonreturntozero (NRZ) level encoder. The resulting binary wave and a sinusoidal carrier (t), whose frequency fc = (nc / Tb) for some fixed integer nc, are applied to a productmodulator as shown fig.1. The carrier and the pulses used to generate the binary wave are
usually extracted from a common master clock. The desired PSK wave is obtained at the
modulator output. To detect the original binary sequence of 1s and 0s, we apply the noisy
PSK signal x (t) (at the channel output) to a correlator, which is also supplied with a
locally generated coherent reference signal 1 (t) as shown fig.2. The correlator output,
X1 is compared with a threshold of zero volts. If X1
-
8/12/2019 Pre Emphasis
43/57
43| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 43
Fig2. Block diagram of BPSK receiver
In PSK modulation and demodulation, the IC 8038 is a basic wave form generator
which generates sine, Triangle and square waveforms. The sine wave generated by this
8038 IC is used as carrier signal to the system. The square wave generated by IC 8038 is
at 12 volts level. So this is converted into a 5 volts signal with the help of a transistor
and diode. This square wave is used as a clock input to a decade counter (IC 7490) which
generates the modulating data outputs. IC CD4051 is an analog multiplex inputs of the
IC. Modulating data input is applied to its control input. Depending upon the level of the
control signal, carrier signal applied with or without phase shift is steered to the output.
The 1800 phase shift of the carrier signal is created by an operational amplifier using 324
IC.
During the demodulation, the PSK signal is converted into a +5 volts square wave
signal using a transistor and is applied to one input of an EX OR gate. To the secondinput of the gate, carrier signal is applied after conversion into a +5 volts signal. So the
EXOR gate output is equivalent to the modulating data signal.
Procedure:
1. Switch on PSK modulation and demodulation trainer.
2. Connect the carrier O/P of carrier generator to the carrier I/P of modulator.
3. Connect the data O/P of Data generator to the Data I/P of Modulator.
4. Connect CH1 OF CRO to Data generator o/p and CH2 to the PSK O/P of modulator.
5. Compare these two signals.
6. Connect the PSK O/P of modulator to the PSK I/P of demodulator.
7. Connect the carrier O/P of carrier generator to carrier I/P of demodulator.
8. Connect CH1 OF CRO to Data generator o/p and CH2 to the demodulator o/p.
9. Compare these two signals.
-
8/12/2019 Pre Emphasis
44/57
44| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 44
Observations:
Carrier voltage = 5.68 volts; Carrier frequency = 5.681 K Hz
Waves Voltage(volts) Bit duration(micro seconds)
Bit 1 Bit 0
Data input-1
Data input-2
Data input-3
Data input-4
Bit clock voltage = ; clock on time period =
-
8/12/2019 Pre Emphasis
45/57
45| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 45
-
8/12/2019 Pre Emphasis
46/57
-
8/12/2019 Pre Emphasis
47/57
47| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 47
Result:
-
8/12/2019 Pre Emphasis
48/57
48| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 48
12. DIFFERENTIAL PHASE SHIFT KEYING
Aim: To study the various steps involved in generating differential phase shift keyed
signal at the modulator end and recovering the binary signal from the received DPSK
signal.APPARATUS :
1. Differential Phase shift keying Trainer.
2. CRO
3. Connecting Wires.
Theory:
DPSK may be viewed as the non-coherent version of PSK. It eliminates the need
for a coherent reference signal at the receiver by combining two basic operations at the
transmitter:1. Differential encoding of the input binary wave and
2. Phase-Shift Keying hence, the name, differential phase shift keying (DPSK).
In effect to send symbol 0, we phase advance the current signal wave-form by
1800, and to send symbol 1, we leave the phase of the current signal waveform
unchanged. The receiver is equipped with a storage capability, so that it can measure the
relative phase difference between the waveforms received during two successive bit
intervals. Provided that the unknown phase contained in the received wave variesslowly, the phase difference between wave forms received in two successive bit intervals
will be independent of .The block diagram of a DPSK transmitter is shown in fig.1 below. It consists, in
part of a logic network and a one-bit delay element interconnected so as to convert the
binary sequence {b k} into a differentially encoded sequence {d k}. This sequence is
amplitude level encoded and then used to modulate a carrier wave of frequency fc,
thereby producing the desired DPSK signal.
-
8/12/2019 Pre Emphasis
49/57
-
8/12/2019 Pre Emphasis
50/57
50| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 50
input, after one-bit delay the same signal is given. So the output of this EX-OR gate is
modulating signal.
PROCEDURE :
1. Switch on differential Phase shift Keying trainer.
2. Connect the carrier output of carrier generator to the 13th pin of CD4051 (Analog
mux) of modulator.
3. Connect the Bit clock output to the Bit clock input at pin 3 of 7474 (8-bit converter) of
modulator.
4. Connect the data output of data generator to the input of modulator circuit.
5. Connect channel 1 of CRO to the data generator.
6. Observe the differential data output at pin 2 of 7474 IC on channel -1 of CRO.
7. Observe the DPSK modulated output on channel-2 of CRO.
8. During demodulation, connect the DPSK modulated output to the DPSK I/P of
Demodulator.
9. Connect the Bit clock O/P to the Bit clock I/P of Demodulator and also connect the
carrier O/P to the carrier I/P of demodulator.
10.Observe the demodulated data O/P at demodulator.11.The frequency of modulation data signal should be equal to the demodulated O/P.
Observations:Carrier voltage = 5.04volts; Carrier frequency = 5.618 K Hz.
Waves Amplitude(volts) Duration of Bits(micro seconds)
Bit 1 Bit 0
Data input-1
Data input-2
Data input-3
Data input-4
Bit clock voltage = ; clock on-time =
clock off-time =
-
8/12/2019 Pre Emphasis
51/57
51| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 51
Differential output
corresponding to
Amplitude(volts) Duration of Bits
(micro seconds)
Bit 1 Bit 0
Data input-1
Data input-2
Data input-3
Data input-4
-
8/12/2019 Pre Emphasis
52/57
52| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 52
-
8/12/2019 Pre Emphasis
53/57
53| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 53
-
8/12/2019 Pre Emphasis
54/57
54| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 54
Result:
-
8/12/2019 Pre Emphasis
55/57
55| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 55
13. TIME DIVISION MULTIPLEXING
Aim:To verify the operation of Time Division Multiplexing
Apparatus:
1. Time Division Multiplexing and De Multiplexing Trainer
2. CRO
3. BNC Probes & Connecting Wires
Theory:The Sampling Theorem provides the basis for transmitting the information
contained in a band limited message signal m (t) as a sequence of samples of m (t) taken
uniformly at a rate that is usually slighter higher than the nyquist rate. An important
feature of the sampling process is a conservation of time. That is, the transmission the
message samples engages the communication channel s for only a fraction of the
sampling interval on a periodic basis, and in this way some of the time interval between
adjacent samples is cleared for use by other independent message sources on a time
shared basis. We there by obtain a time division multiplexing (TDM) system, which
enables the joint utilization of a common communication channel by a plurality of
independent message sources without mutual interference among them.
The TDM system is highly sensitive to dispersion in the common channel, that is,
to variations of amplitude with frequency or lack of proportionality of phase with
frequency. Accordingly, accurate equalization of both magnitude and phase response of a
channel is necessary to ensure a satisfactory operation of the system. Unlike FDM, TDMis immune to non linearities in the channel as a source of cross talk. The reason for this is,
the different message signals are not simultaneously applied to the channel.
The primary advantage of TDM is that several channels of information can be
transmitted simultaneously over a single cable.
In the circuit diagram the 555 timer is used as a clock generator. This
timer is a highly stable device for generating accurate time delays. In this circuit this
timer generates clock signal, which is of 100 KHz frequency (approximately). This clock
signal is connected to the 74163 IC, it is synchronous presettable binary counter. It
divides the clock signal frequency into three parts and those are used as selection lines for
multiplexer and de-multiplexer. Inbuilt signal generator is provided with sine, square andtriangle outputs with variable frequency. These three signals can be used as inputs to the
multiplexer. IC 4051 is an 8 to 1 Analog Multiplexer. It selects one-of-eight signal
sources as a result of unique three bit binary code at the select inputs. Again IC 4051 is
wired as one to eight de-multiplexers. Demux input receives the data source and transmits
the data signals on different channels.
-
8/12/2019 Pre Emphasis
56/57
56| P a g e
P.R.Ratna Raju.K, ECE, MITS Page 56
Kit Diagram:
Waveforms:
Input to the Multiplexer:
Multiplexed output:
-
8/12/2019 Pre Emphasis
57/57
57| P a g e
Demultiplexed Output:
Observations:
S. No Signals Amplitude(v p-p) Time period
(milli seconds)
1 Square wave
2 Sinusoidal wave
3 Triangular wave
4 Clock signal
Result: