Table of Contents

Pre-Delivery Manual3P-FF600, 3P-FF800, and 3P-FF900

Front Fold 3-Point Sprayer

Manufacturing, Inc.www.greatplainsmfg.com

Read the operator manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!

Illustrations may show optional equipment not supplied with standard unit.

!

22892

© Copyright 2017 Printed 8/29/17 500-643Q

EN

Table of Contents

ORIGINAL INSTRUCTIONS

Table of Contents

Table of Contents

3P-FF600, 3P-FF800, 3P-FF900 Cover iii

Table of Contents

Important Safety Information.................................................1Introduction.............................................................................6

Description of Unit .............................................................6Intended Usage ..........................................................6

Using This Manual.............................................................6Assembly.................................................................................7

Tools Required ..................................................................7Pre-Assembly Checklist.....................................................7Unload Sprayer from Truck ...............................................8Remove Shipping Straps...................................................8Marker Tank ......................................................................8

Boom Lock Cable ..............................................................9Outer Jump Nozzle............................................................9

Preparation and Setup .........................................................10Before You Start..............................................................10Hitching Tractor to Sprayer .............................................10

Hydraulic Drive Pumps.............................................12Ace Pump Flow Limiter (Option) ..............................13

Appendix - Reference Information......................................14Specifications and Capacities .........................................14Torque Values .................................................................15

8/29/17 Cover 500-643Q

© Copyright 2006, 2017 All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has beentaken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed fordamages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products asit sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, Max-Chisel, Row-Pro, Singulator Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.

Registered Trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone, Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-Till, Ultra-Till, Whirlfilter, and Yield-Pro.

Brand and Product Names that appear and are owned by others are trademarks of their respective owners.Printed in the United States of America

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents iv

8/29/17 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents 1

Important Safety Information

Look for Safety SymbolThe SAFETY ALERT SYMBOL indicates there is apotential hazard to personal safety involved and extrasafety precaution must be taken. When you see thissymbol, be alert and carefully read the message thatfollows it. In addition to design and configuration ofequipment, hazard control and accident prevention aredependent upon the awareness, concern, prudence andproper training of personnel involved in the operation,transport, maintenance and storage of equipment.

Be Aware of Signal WordsSignal words designate a degree or level of hazardseriousness.

DANGER indicates an imminently hazardous situationwhich, if not avoided, will result in death or serious injury.This signal word is limited to the most extreme situations,typically for machine components that, for functionalpurposes, cannot be guarded.

WARNING indicates a potentially hazardous situationwhich, if not avoided, could result in death or seriousinjury, and includes hazards that are exposed whenguards are removed. It may also be used to alert againstunsafe practices.

CAUTION indicates a potentially hazardous situationwhich, if not avoided, may result in minor or moderateinjury. It may also be used to alert against unsafepractices.

Be Familiar with Safety Decals Read and understand information on safety decals in the

Operator’s Manual.

Read all instructions noted on the decals.

Avoid High Pressure Fluids Escaping fluid under pressure can penetrate the skin,

causing serious injury. If hydraulic fluid penetrates theskin under pressure, immediate medical attention isrequired. See a physician familiar with this type of injury

Avoid the hazard by relieving pressure beforedisconnecting hydraulic lines.

Use a piece of paper or cardboard, NOT BODY PARTS, tocheck for suspected leaks.

Wear protective gloves and safety glasses or goggles whenworking with hydraulic systems.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Important Safety Information 2

Wear Protective EquipmentGreat Plains advises all users of chemical pesticides orherbicides to use the following personal safetyequipment.

Waterproof, wide-brimmed hat

Waterproof apron.

Face shield, goggles or full face respirator.

Goggles with side shields or a full face respirator isrequired if handling or applying dusts, wettable powders,or granules or if being exposed to spray mist.

Cartridge-type respirator approved for pesticide vaporsunless label specifies another type of respirator.

Waterproof, unlined gloves. Neoprene gloves arerecommended.

Cloth coveralls/outer clothing changed daily; waterproofitems if there is a chance of becoming wet with spray

Waterproof boots or foot coverings

Do not wear contaminated clothing. Wash protectiveclothing and equipment with soap and water after eachuse. Personal clothing must be laundered separately fromhousehold articles.

Clothing contaminated with certain pesticides must bedestroyed according to state and local regulations. Readchemical label for specific instructions.

Wear clothing and equipment appropriate for the job.Avoid loose-fitting clothing.

Prolonged exposure to loud noise can cause hearingimpairment or loss. Wear suitable hearing protection suchas earmuffs or earplugs.

Avoid wearing entertainment headphones while operatingmachinery. Operating equipment safely requires the fullattention of the operator.

Keep Riders Off Machinery Riders obstruct the operator’s view. Riders could be struck

by foreign objects or thrown from the machine.

Never allow children to operate equipment.

Keep all bystanders away from machine during operation.

Use Safety Lights and Devices Slow-moving tractors and towed implements can create a

hazard when driven on public roads. They are difficult tosee, especially at night.

Use flashing warning lights and turn signals wheneverdriving on public roads.

Use tractor lights and lights provided with implement.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Important Safety Information 3

Check for Overhead Lines

Sprayer booms contacting overhead electrical lines canintroduce lethal voltage levels on sprayer and tractor frames.A person touching almost any metal part can complete thecircuit to ground, resulting in serious injury or death. Athigher voltages, electrocution can occur without directcontact.

Avoid overhead lines during sprayer operations.

Transport Machinery Safely Maximum transport speed for implement is 20 mph (32

kph). Some rough terrains require a slower speed. Suddenbraking can cause a towed load to swerve and upset.

Do not exceed 20 mph (32 kph). Never travel at a speedwhich does not allow adequate control of steering andstopping. Reduce speed if towed load is not equipped withbrakes.

Comply with state and local laws.

Do not tow an implement that, when fully loaded, weighsmore than 1.5 times the weight of towing vehicle.

Carry reflectors or flags to mark Front Fold BoomSprayer in case of breakdown on the road.

Keep clear of overhead power lines and otherobstructions when transporting. Refer to transportdimensions under “Specifications and Capacities” onpage 14.

Do not fold or unfold the Front Fold Boom Sprayer whilethe tractor is moving.

Shutdown and Storage Fold Front Fold Boom Sprayer, put tractor in park, turn off

engine, and remove the key.

Secure Front Fold Boom Sprayer using blocks andsupports provided.

Detach and store Front Fold Boom Sprayer in an areawhere children normally do not play.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Important Safety Information 4

Practice Safe Maintenance Understand procedure before doing work. Use proper

tools and equipment. Refer to this manual for additionalinformation.

Work in a clean, dry area.

Fold the Front Fold Boom Sprayer, put tractor in park,turn off engine, and remove key before performingmaintenance.

Make sure all moving parts have stopped and all systempressure is relieved.

Allow Front Fold Boom Sprayer to cool completely.

Disconnect battery ground cable (-) before servicing oradjusting electrical systems or before welding on FrontFold Boom Sprayer.

Inspect all parts. Make sure parts are in good conditionand installed properly.

Remove buildup of grease, oil or debris.

Remove all tools and unused parts from Front Fold BoomSprayer before operation.

Prepare for Emergencies Be prepared if a fire starts.

Keep a first aid kit and fire extinguisher handy.

Keep emergency numbers for doctor, ambulance, hospitaland fire department near phone.

Tire Safety Tire changing can be dangerous and should be performed

by trained personnel using correct tools and equipment.

When inflating tires, use a clip-on chuck and extensionhose long enough for you to stand to one side–not in frontof or over tire assembly. Use a safety cage if available.

When removing and installing wheels, use wheel-handlingequipment adequate for weight involved.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Important Safety Information 5

Safety At All Times Thoroughly read and understand the instructions in this

manual before operation. Read all instructions noted onthe safety decals.

Be familiar with all Front Fold Boom Sprayer functions.

Operate machinery from the driver’s seat only.

Do not leave Front Fold Boom Sprayer unattended withtractor engine running.

Do not dismount a moving tractor. Dismounting a movingtractor could cause serious injury or death.

Do not stand between the tractor and Front Fold BoomSprayer during hitching.

Keep hands, feet and clothing away from power-drivenparts.

Wear snug-fitting clothing to avoid entanglement withmoving parts.

Watch out for wires, trees, etc., when folding and raisingFront Fold Boom Sprayer. Make sure all persons are clearof working area.

Do not turn tractor too tightly, causing Front Fold BoomSprayer to ride up on wheels. This could cause personalinjury or equipment damage.

Use only water without pesticides added to calibrate thesprayer. Do not exceed the calibrated sprayer speed andpressure when operating.

When using a PTO pump, be sure that PTO shield is inplace on the tractor, PTO coupler bolts are torqued to thecorrect specification, and torque bar is properly chainedto tractor drawbar.

Spray with the boom in the unfolded position only.

The boom has many pinch points during field operationand folding. Keep all bystanders away.

Never use tank for potable water.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents 6

Introduction

Great Plains welcomes you to its growing family of newproduct owners. This Front Fold 3-Point Sprayer hasbeen designed with care and built by skilled workersusing quality materials. Proper setup, maintenance andsafe operating practices will help you get years ofsatisfactory use from the machine.

Description of UnitThe 3P-FF600, 3P-FF800, and 3P-FF900 sprayers arecapable of spraying at either 60ft or the full 80-90ftdepending on your application needs. The level floatboom is fully suspended starting with vertical springsuspension in a 46in hydraulic elevator which provides awide range of boom height adjustment along with gasshocks that provide side-to-side stability.

Intended UsageUse these booms as part of a pressurized sprayersystem to apply liquid pesticides, herbicides or fertilizersto production-agriculture crops only. Do not modifysprayer for use with attachments other than thoseapproved by Great Plains.

Models Covered

Using This ManualThis manual was written to help you assemble andprepare the new machine for the customer. The manualincludes instructions for assembly and setup. Read thismanual and follow the recommendations for safe,efficient and proper assembly and setup.

An operator’s manual is also provided with the newmachine. Read and understand “Important SafetyInformation” and “Operating Instructions” in theoperator’s manual before assembling the machine. As areference, keep the operators’s manual on hand whileassembling.

The information in this manual is current at printing.Some parts may change to assure top performance.

DefinitionsThe following terms are used throughout this manual.

Right-hand and left-hand as used in this manual aredetermined by facing the direction the machine will travelwhile in use unless otherwise stated.

Paragraphs in this format present a crucial point of informationrelated to the current topic. Read and follow the directions to:- remain safe,- avoid serious damage to equipment and- ensure desired field results.

NOTE:Paragraphs in this format provide useful informationrelated to the current topic.

Further AssistanceFor additional help with understanding these assemblyinstructions or for any other assembly or setup relatedquestions, please contact our service department at thefollowing address:

Great Plains Service Department1525 E. North St.

P.O. Box 5060Salina, KS 67402-5060

Or call us at (800) 270-9302 to speak over the phonewith a service representative.

Copies of this machine’s operator manual are availableby mail or online. Please visit www.greatplainsag.comand follow the product link for information on yourmachine.

3P-FF600-3620 3-Point Sprayer 60 foot 20 inch spacing

3P-FF600-2530 3-Point Sprayer 60 foot 30 inch spacing

3P-FF800-4820 3-Point Sprayer 80 foot 20 inch spacing

3P-FF800-3330 3-Point Sprayer 80 foot 30 inch spacing

3P-FF900-5420 3-Point Sprayer 90 foot 20 inch spacing

3P-FF900-3730 3-Point Sprayer 90 foot 30 inch spacing

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents 7

Assembly

The following headings are step-by-step instructions forassembling the Front Fold 3-Point Sprayer. Begin withTools Required and Pre-Assembly Checklist to makesure you have all necessary parts and equipment. Thenproceed with Unload Sprayer from Truck. Follow eachstep in order to make the job as quick and safe aspossible and produce a properly working machine.

The Front Fold 3-Point Sprayer is shipped via flat bedtruck. It is the dealer’s responsibility to unload thesprayer. Unload all equipment before beginningassembly. Do not attempt any assembly work with theFront Fold 3-Point Sprayer on the truck.

Tools Required• General hand tools

Pre-Assembly Checklist1. Read and understand “Important Safety

Information” on page 1 before assembling.

2. Have at least two people on hand while assembling.

3. Make sure the assembly area is level and free ofobstructions (preferably an open concrete area).

4. Have all major components.

5. Have all fasteners and pins shipped with boom.

If a pre-assembled part or fastener is temporarily removed,remember where it goes. Keep the parts separated.

6. Have a copy of the parts manual on hand. If unsureof proper placement or use of any part or fastener,refer to the parts manual.

7. Check that all working parts are moving freely, boltsare tight, and cotter pins are spread.

8. Check that safety labels and reflectors are correctlylocated and legible. Replace if necessary. Refer toSafety Decals in the “Important SafetyInformation” chapter of the operator’s manual.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Assembly 8

Unload Sprayer from Truck1. Using a forklift or tractor, remove sprayer from

truck. Do not remove shipping stands until you areready to assemble sprayer.

2. When ready to assemble, place sprayer in an open,level area. Make sure there is enough overheadand side clearance to fold and unfold assembledboom.

Remove Shipping StrapsRefer to Figure 1

3. Unscrew U-bolts to remove shipping straps whichsecure upper portion of boom arms to transportbumpers during shipping.

4. After shipping straps are removed, carefully unfoldsprayer to field position.

5. Refold sprayer to transport position with transportbumpers resting just below boom arms.

Marker TankRefer to Figure 2

6. Mount the marker tank on the right side of thesprayer.

Figure 1Shipping Strap

23240

Figure 2Marker Tank

23243

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Assembly 9

Boom Lock CableRefer to Figure 3 and Figure 4

7. Unhook swivel bolt snap from stationary ring.

8. Re-hook swivel bolt snap to ring located in outerboom lock plunger rod.

9. Carefully unfold sprayer. Consult Operator’s Manualfor procedure.

Outer Jump Nozzle Refer to Figure 5

This section applies only to the following:

• 3P-FF600 36-nozzles at 20in spacing,• 3P-FF800 33-nozzles at 30in spacing, and• 3P-FF900 37-nozzles at 30in spacing.

10. Locate the outer jump nozzle mounting bracket(s)which is/are wire tied to the support frame(s).

11. Undo the wire tie and mount the bracket to the framegusset using the preexisting holes. Make sure thenozzle is positioned as shown.

Figure 3Swivel Bolt Snap (transport)

24164

Figure 4Swivel Bolt Snap (operation)

24165

Figure 5Outer Jump Nozzle

23239

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents 10

Preparation and Setup

Before You StartRead and understand the owners manual for yoursprayer. A basic understanding of how the sprayer workswill aid in the assembly, setup and operation of yoursprayer.

Perform these checks before setting up your front foldboom.

1. Read and understand “Important SafetyInformation” on page 1.

2. Check that all working parts are moving freely, boltsare tight, and cotter pins are spread.

3. Check that all grease fittings are in place andlubricated.

4. Check that all safety decals and reflectors arecorrectly located and legible. Replace if damaged.

Hitching Tractor to Sprayer

Crushing Hazard:You may be severely injured or killed by being crushedbetween the tractor and Front Fold 3-Point Sprayer. Do notstand or place any part of your body between Front Fold 3-Point Sprayer and moving tractor. Stop tractor engine and setpark brake before installing the hitch pin.

Electrocution Hazard:To prevent serious injury or death from electric shock, keepclear of overhead power lines when transporting, folding orunfolding boom. Boom is not grounded. Electrocution canoccur without direct contact.

Refer to the transport dimensions in “Specificationsand Capacities” on page 14.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Preparation and Setup 11

Be certain that tractor lift capacity is adequate and thattractor is weighted to maintain steering control. Failure to doso may cause loss of vehicle control.

Refer to tractor specifications for tractor lift capacity andsee “Specifications and Capacities” on page 14, forrequired lift capacity. Consult the tractor operator’smanual for tractor weighting recommendations.

Refer to Figure 6

5. Determine the pin and spacer orientation needed forthe tractor, and securely fasten the hitch pins.

6. Mount the 3-Point Sprayer to a tractor with thecorrect pin mountings determined from instructionStep 1. Make sure that the sprayer frame is level sothat after the boom is assembled, it won’t hit thetractor cab when the boom is folded or raised.

The category 4 narrow hitch (CAT IV-N) spacers are notstandard parts supplied with the 3-Point Sprayer. Order 501-011S from a Great Plains dealer for the CAT IV-N spacers.

NOTE:Be sure that the top 3-Point link is adjusted correctlyso that the frame is level in operating position but willnot hit the cab in transport. The tractor 3-Point armsshould be adjusted to keep the sprayer level fromside to side with lift arm rigid.

Figure 6Pin & Spacer Configuration

12654

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Preparation and Setup 12

Predelivery1. Have tractor delivered to dealership that will be

operating sprayer.

2. Confirm row spacing.

3. Hook sprayer to tractor.

4. Install control switch boxes inside of tractor cab, androute power supplies to the tractor battery.

5. The following equipment must be connected to thetractor’s battery: Raven 440/450 Controller, FasseValve Hydraulic Control Box, and Optional FoamMarker Control.

a. To connect the Raven 440/450 Controller to thetractor battery, see the Raven Installation andService Manual.

b. To connect the Fasse Valve Hydraulic ControlBox to the tractor battery:• Use the 6-foot, two-wire red and black cable

to connect hydraulic controls.• Connect the red wire from each cable to the

positive terminal and the black wire fromeach cable to the negative terminal.

c. Use the 6-foot gray cable to connect the optionalfoam marker control to the tractor battery.

6. Mount radar gun to tractor frame if applicable androute cable up through cab. If using existing radar ontractor, install “Y” cable according to tractormanufacturer’s recommendations.

7. Connect all hydraulic hoses to outlets (refer to tractoroperator’s manual for designated outlet if equippedwith a hydraulic pump).

The hydraulic motor used on all liquid pumps is a 6GPM motor. If the tractor used on this sprayer doesnot have the capabilities to adjust the remotes to thisflow, then a hydraulic flow divider kit must beinstalled so that flow can be controlled and to preventoperating the pump at excessive speeds.

Place a stop in the neutral position for the tractorhydraulics so that the hydraulic lever can only bemoved to the float and down positions. Refer to thetractor’s operator manual on information for theneutral stop.

Damage to the pump will occur if the hydraulic lever isreturned to the neutral position while the pump is running.

8. Check all hydraulic functions of the boom/elevator.

9. With boom still unfolded, make sure boom locks areadjusted correctly to just clear the stops.

10. Fill sprayer approximately 1/2 full of water. Open tanksump valve and let water circulate throughout thesystem and check for any leaks.

11. Before installing nozzles, engage pump slowly andcirculate water through the system, then turn onboom valves individually to flush out the system.

On sprayers equipped with a hydraulic pump, startout with the hydraulic lever in the float position, andengage the pump by placing the lever in the downposition. Make sure the hydraulic flow control valve isset at a minimum flow.

12. After system has been thoroughly flushed, installnozzles and open boom valves again to checknozzle pattern across the boom.

13. Set the dead head pressure of the pump in thefollowing ways depending on how pump is driven.

Hydraulic Drive Pumpsa. To determine the correct flow rate to the

hydraulic motor, start out with the hydrauliccontrol valve set at a minimum flow, and thehydraulic lever in the float position.

b. Open up the sprayer control valve to itsmaximum setting.On the Raven 450 monitor, with the power switchon, the rate switch must be placed in the manualposition, and the increase/decrease switch mustbe pushed to increase for 10-12 seconds.

c. Start the tractor and engage the pump by placingthe hydraulic lever in the down position. Oncethe system builds pressure, speed up the tractorto normal operating speed.Shut off the boom section switches, and closethe agitation valve.

d. The pump is now at deadhead pressure and thehydraulic control valve must be adjusted up untilthe spray pressure reaches 80 psi maximum.Mark this setting on the hydraulic control valvefor future reference.

e. Open up the agitation valve.

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Preparation and Setup 13

Ace Pump Flow Limiter (Option)Refer to Figure 7

The flow limiter is a hydraulic device designed to shut offthe flow of hydraulic oil when a specified flow rate isexceeded. On tractors with load sensing closed centerhydraulic systems, this device limits the flow of oil to theAce motor and prevents failures.

Newer Case-IH, John Deere, New Holland, and CATtractors have a great potential to run motors beyondtheir rated speeds. Flows out of the hydraulic valves canexceed 20 GPM while the motors are rated at 4-11GPM. The flow limiter protects the Ace motor by shuttingoff on excess hydraulic flow.

The flow limiter should not be used on open center orpressure compensating closed center hydraulicsystems. The flow limiter should not be used with arestrictor orifice.

To Install Pump Flow Limiter

1. Install the flow limiter in the inlet port of the Acemotor.

2. Connect the hydraulic hoses so that the pump runswith the hydraulic lever in the lower/retract position.Connect return hose to Low Pressure Return Port,when available.

3. Shut off boom and agitation valves on the sprayer todeadhead the sprayer pump flow.

4. Adjust the flow control on the tractor to minimumflow setting (turtle).

5. Move hydraulic lever to the lower/retract position.

NOTE:Always shut the pump off in the float position. Thiseliminates high pressure being trapped in the returnline and protects hydraulic seals. Avoid returning theoil to the remote valve; use the Low Pressure ReturnPort, when available.

6. Adjust the flow control on the tractor until thesprayer system deadhead pressure is within thepump’s operating parameters:

If the flow limiter stops the flow of oil to the motor

a. Move the hydraulic lever to the neutral position.This removes the oil pressure from the flowlimiter and allows it to reset.

b. Adjust the flow control to a lower flow position.c. Repeat steps 5 and 6.

7. Set sprayer pressure by opening the agitation valve.

Figure 7Ace Pump Flow Limiter

23395

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents 14

Appendix - Reference Information

Specifications and Capacities

3P-FF600 3P-FF800 3P-FF900

Boom Width 60 foot 60 foot- 80 foot 60 foot - 90 foot

Nozzle Spacing 20-inch or 30-inch

Number Of Nozzles 36 (20-inch spacing) 25 (30-inch spacing)

48 (20-inch spacing) 33 (30-inch spacing)

54 (20-inch spacing)37 (30-inch spacing)

Approx. Weight 4410 lbs 5500 lbs 5550 lbs

Working Width 63 feet 83 feet 93 feet

Transport Width 12 feet 13 feet 13 feet

Transport Height 13 feet

Depth*

* Behind lower link point

82 inches

Lift Capacity†

† At 24 inches behind lower lift-arm balls

8000 lbs 10,200 lbs 10,300 lbs

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Appendix - Reference Information 15

Torque Values

94 6

25199m

BoltSize

Bolt Head IdentificationBoltSize

Bolt Head Identification

Grade 2 Grade 5 Grade 8 Class 5.8 Class 8.8 Class 10.9in-tpia N-mb N-m N-m mm x pitchc N-m N-m N-m1⁄4-20 7.4 11 16 M 5 X 0.81⁄4-28 8.5 13 18 M 6 X 1 7 11 155⁄16-18 15 24 33 M 8 X 1.25 17 26 365⁄16-24 17 26 37 M 8 X 1 18 28 393⁄8-16 27 42 59 M10 X 1.5 33 52 723⁄8-24 31 47 67 M10 X 0.75 39 61 857⁄16-14 43 67 95 M12 X 1.75 58 91 1257⁄16-20 49 75 105 M12 X 1.5 60 95 1301⁄2-13 66 105 145 M12 X 1 90 105 1451⁄2-20 75 115 165 M14 X 2 92 145 2009⁄16-12 95 150 210 M14 X 1.5 99 155 2159⁄16-18 105 165 235 M16 X 2 145 225 3155⁄8-11 130 205 285 M16 X 1.5 155 240 3355⁄8-18 150 230 325 M18 X 2.5 195 310 4053⁄4-10 235 360 510 M18 X 1.5 220 350 4853⁄4-16 260 405 570 M20 X 2.5 280 440 6107⁄8-9 225 585 820 M20 X 1.5 310 650 900

7⁄8-14 250 640 905 M24 X 3 480 760 1050

1-8 340 875 1230 M24 X 2 525 830 1150

1-12 370 955 1350 M30 X 3.5 960 1510 2100

11⁄8-7 480 1080 1750 M30 X 2 1060 1680 2320

11⁄8-12 540 1210 1960 M36 X 3.5 1730 2650 3660

11⁄4-7 680 1520 2460 M36 X 2 1880 2960 4100

11⁄4-12 750 1680 2730

13⁄8-6 890 1990 3230 a. in-tpi = nominal thread diameter in inches-threads per inch

13⁄8-12 1010 2270 3680 b. N· m = newton-meters

11⁄2-6 1180 2640 4290

11⁄2-12 1330 2970 4820

c. mm x pitch = nominal thread diameter in mm x thread pitch

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

5.8 8.8 10.9

25199

ft-lbd ft-lb ft-lb ft-lb ft-lb ft-lb5.6 8 12

6 10 14 5 8 11

11 17 25 12 19 27

13 19 27 13 21 29

20 31 44 24 39 53

22 35 49 29 45 62

32 49 70 42 67 93

36 55 78 44 70 97

49 76 105 66 77 105

55 85 120 68 105 150

70 110 155 73 115 160

79 120 170 105 165 230

97 150 210 115 180 245

110 170 240 145 230 300

170 265 375 165 260 355

190 295 420 205 325 450

165 430 605 230 480 665

185 475 670 355 560 780

250 645 910 390 610 845

275 705 995 705 1120 1550

355 795 1290 785 1240 1710

395 890 1440 1270 1950 2700

500 1120 1820 1380 2190 3220

555 1240 2010

655 1470 2380

745 1670 2710

870 1950 3160d. ft-lb = foot pounds

980 2190 3560

3 5 7

08/29/2017 Table of Contents 500-643Q

3P-FF600, 3P-FF800, 3P-FF900 Table of Contents Appendix - Reference Information 16

08/29/2017 Table of Contents 500-643Q

Table of Contents

Table of Contents

Great Plains, Mfg.1525 E. North St.P.O. Box 5060Salina, KS 67402