Practice Questions Graphicsij
Transcript of Practice Questions Graphicsij
-
1
PRACTICE QUESTIONS GRAPHICS These questions have been taken from official syllabus for PYP-004 and contribute to the preparation for Theory Test and also for Final Examination.
2014
M.B. Ahmed Lecturer, CASS, KFUPM
1/12/2014
-
2
Lectures Plan
First Lecture Objectives
Introduction to Graphics & Engineering Drawing
The concept of views
Orthographic Projection
Concept of Hidden Lines
Exercises in the book (page numbers: 05-12)
Second Lecture Objectives
Introduction to AutoCAD User Interface
Drawing Environment (Status bar, Drawing Units & Drawing Limits)
Draw Commands
Drawing Lines (Direct Distance Entry Method)
Dimension Tool bar
Lesson one in the book
Third Lecture Objectives
Draw Commands
Lesson two and three in the book
Fourth Lecture Objectives
Modify Commands
Practice Exercises in the book
Fifth Lecture Objectives
Continuation of Modify Commands
Assessment
-
3
INSTRUCTIONS:
These questions are lecture-wise arranged. Students should attempt the questions under
LECTURE ONE heading after first week and so on.
In the end there are solved exercises.
All the questions in this file are important for Theory Test and also helpful for Final Exam
LECTURE ONE
CONCEPTS OF ORTHOGRAPHIC VIEWS
1. Orthographic Projection is used to show two dimension surface of a three dimensioned object.
a. True
b. False
2. In third angle of projection, the top view of an isometric projection is projected on ____ plane
a. Front
b. Side
c. Top
3. Orthographic drawing refers to a 2D (two-dimensional) representation of an object in a view that shows only ----------- at a time.
a. One side
b. Two sides
c. Three sides
d. All sides
4. The following symbol is used to show:
:
a. First angle of projection b. Third angle of projection
5. Which one of the following figure is plan for the object?
-
4
ANS__________
6. How many hidden lines will be drawn in front view of the object shown in Figure 01?
a. one
b. two
c. Four
d. None
-
5
7. How many hidden lines will be drawn in Right End Elevation view of the object shown in Figure 02?
a. Four
b. One
c. Two
d. Six
8. Name the Orthographic projection view a in fig-03?
a. Plan
b. Front
c. R.H End Elevation
d. L.H End Elevation
-
6
9. How many hidden lines will be drawn in the top view of the object shown in above figure?
a. 2
b. 4
c. 6
d. No hidden lines will be drawn
10. In the adjacent figure, the front view dimensions are--------------?
a. 80, 40, 10, 20
b. 40, 20, 30
c. 80, 20, 10, 05
d. 10, 20,70, 60
11. The following symbol is used to show:
a. First angle of projection b. Third angle of projection
12. The following symbol is used to show:
-
7
a. First angle of projection b. Third angle of projection
13. What type of view is it?
a. Perspective
b. Orthographic
c. Isometric
14. In the front view of figure (Q:15), the hole feature will be shown as _____.
a. Continuous lines
b. Hidden Lines
c. Broken Lines
15. In third angle of projection, the front view of an isometric projection is projected on ____ plane
a. Front
b. Side
c. Top
16. What type of drawing is it?
a. Isometric
b. Orthographic
c. Isobaric
d. None of above
-
8
17. What is the angle of projection, for the adjacent figure?
a. First Angle
b. Second Angle
c. Third Angle
d. None of above
18. Which dimensions will be used for rectangular cut on the base of figure-04?
a. 15-35-120-15
b. 15-50-15-50
c. 35-120-35-120
-
9
19. How many hidden lines will be drawn in the top view of the object shown in above figure?
a. 2
b. 4
c. 6
d. No hidden lines will be drawn
-
10
LECTURE TWO
INTRODUCTION TO AUTOCAD AND DRAWING AIDS
20. In which bar do you find the Ortho & Osnap icon?
a. Draw toolbar
b. Modify toolbar
c. Status bar
d. Object properties toolbar
21. Drafting Settings dialogue box can be accessed using _____________
a. Tools Menu
b. Format Menu
c. Edit Menu
22. Always use __________ to pick dimension line origins.
a. Ortho Mode
b. Snap
c. Osnap
23. To print drawings we should use ______ space
a. Model
b. Paper
24. You can quickly open an existing document using ------tool bar
a. Standard
b. Menu
c. Property
-
11
25. Which of the following can be drawn using Object Property Tool Bar
a. Circle
b. Rectangle
c. Hidden Line
26. Which of the following mode you would use to pick the dots on regular grids?
a. OSNAP
b. SNAP
c. ORTHO
27. In Auto-CAD object snap is used to pick accurately--------------of a line.
a. End point
b. Mid point
c. Nearest point
d. All of above
28. Format and Tools Buttons lie on ------Tool Bar
a. Menu
b. Standard
c. Property
29. The value of drawing units is determined before you draw.
a. True
b. False
30. Regular pattern of dots displayed on the screen and acting as a visual aid are called______
a. Drawing Units
b. Drawing grid
31. In Orthographic projection, projection lines are ------------ to image plane.
a. parallel
b. perpendicular
c. at 45 degrees
32. In orthographic projection, the perpendicular distance between the views
-
12
is________
a. 10 mm
b. 20mm
c. Same
33. In AutoCAD user interface, ________ displays prompts and messages.
a. Command Window
b. Drawing Area
c. Standard Tool Bar
34. In AutoCAD, Ortho command is used to draw--------------lines.
a. Perpendicular
b. Inclined
c. Polyline
d. All of above
35. Which of the following pairs are found on Status Bar
a. Snap and Grid
b. Units and Limits
c. Dimension and Text
36. _______ is used to change the line type.
a. Standard Tool Bar
b. Property Tool Bar
c Format Tab
-
13
LECTURE THREE
AUTOCAD DRAW COMMANDS
37. What does this icon represent?
a. Rectangle
b. Line
c. Parallelogram
38. Name the AutoCAD tool bar where you find the hidden Line Types?
a. Draw Toolbar
b. Modify Toolbar
c. Command Line
d. Object Properties Toolbar
39. In AutoCAD, a polyline can be drawn by:
a. Draw Tool bar
b. Modify tool bar
c. Object properties tool bar
40. In AutoCAD, a circle can be drawn by
a. centre, radius
b. Centre Diameter
c. Start, centre, end
d. 3 points
e. All of the above
41. After starting circle command, _______ should be specified first.
a. Radius of circle
b. Diameter of circle
c. Centre point of circle
-
14
42. In AutoCAD, an arc can be drawn by the following command:
a. Start, End, Radius
b. Start, End, Direction
c. Three Points
d. All of above
43. Draw Commands can be started by _____ ways
a. one
b. Two
c. Three
44. Which command would you use to draw connected sequence of many line segments with different thickness?
a. Continuous Line Command
b. Multi Line Command
c. Polyline Command
45. The _____ command is used to dimension along straight lines.
a. DIMDIAMETER
b. DIMALIGNED
c. DIMLINEAR
-
15
LECTURE FOUR
AUTOCAD MODIFY COMMANDS
46. AutoCAD draw tool bar symbol is used for ------------command.
a. Pentagon
b. Rectangle
c. Array
d. Construction line
47. Fillet command can be started using draw-toolbar
a. True
b. False
48. Identify the following symbol, found in modify tool bar.
a. Offset
b. Scale
c. Mirror
d. Cloud
49. Which command can be started using this icon?
a. Offset
b. Trim
c. Fillet
50. What does this icon represent?
a. Circle
b. Polygon
c. Ellipse
51. Which tool bar does this icon lie on?
a. Draw tool bar
b. Modify tool bar
-
16
c. None of these
52. What does this icon represent?
a. Extend
b. Copy
c. Mirror
53. Offsetting and copying the same circle will give same result
a. True
b. False
54. R.H End Elevation can be used to have L.H End elevation by using_______command
a. Copy command
b. Mirror Command
c. Copy Command
55. Which of the following command can be used to create one or more duplicates of any drawing objects?
a. Mirror Command
b. Copy Command
c. Offset Command
56. Cutting edge must be defined while using______ command
a. Erase Command
b. Trim Command
c. Extend Command
57. What does this AutoCAD symbol represent?
a. Inclined
b. Chamfer
c. Fillet
d. Radius
58. Which command can be started using this icon?
a. Offset
b. Trim
-
17
c. Extend
59. The ________command is useful for drawing symmetrical objects
a. Offset Command
b. Mirror Command
c. Copy Command
60. What does this AutoCAD icon represent?
a. Arc
b. Spline
c. Polyline
d. Rotate
61. Write the names of the commands these tabs are used for:
LINE COMMAND
ERASE COMMAND
62. Which of the following command you would use to create two concentric circles
a. Mirror
-
18
b. Copy
c. Offset
63. The corners of rectangular shapes can be rounded by using
a. Chamfer Command
b. Move Command
c. Fillet Command
64. To select a number of objects for modification which method is the quickest one?
a. Picking method
b. Window selection