PPIC32020 / PPIC32520 / PPIC34520

User guide

You can find important information and FAQs about this and other products online at:

www.abus.com Version 1.0 Firmware: 1.0.1.40

English translation of the original German user manual. Retain for future reference.

2

English

Introduction Dear Customer, Thank you for purchasing this product. ABUS Security-Center hereby declares that the PPIC32020, PPIC32520 and PPIC34520 cameras comply with RED Directive 2014/53/EU. Additionally, these devices comply with the requirements of the following EU directives: EMC Directive 2014/30/EU and the RoHS Directive 2011/65/EU. The full EU Declaration of Conformity text may be found at:

www.abus.com/product/PPIC32020 www.abus.com/product/PPIC32520 www.abus.com/product/PPIC34520

To ensure this condition is maintained and that safe operation is guaranteed, it is your obligation to observe this user manual. Please read the entire user manual carefully before putting the product into operation, and pay attention to all operating instructions and safety information. All company names and product descriptions are trademarks of the corresponding owner. All rights reserved.

If you have any questions, please contact your specialist installation contractor or specialist dealer.

Data storage is subject to national data privacy guidelines.

Warning as required by §201 StGB (German Criminal Code): Whosoever unlawfully makes an audio recording of the privately spoken words of another, and uses or makes a recording thus produced accessible to a third party, shall be liable to imprisonment or a fine. Whosoever unlawfully overhears with an eavesdropping device the privately spoken words of another not intended for his attention, or publicly communicates, verbatim or the essential content of, the privately spoken words of another, recorded or overheard, shall incur the same penalty.

Disclaimer This user manual has been produced with the greatest of care. Should you discover any omissions or inaccuracies, please contact us in writing at the address provided above. ABUS Security-Center GmbH does not accept any liability for technical and typographical errors, and reserves the right to make changes to the product and user manuals at any time and without prior warning. ABUS Security-Center GmbH is not liable or responsible for direct or indirect damage resulting from the equipment, performance and use of this product. No guarantee is made for the contents of this document.

3

English

Explanation of symbols

The triangular high voltage symbol is used to warn of the risk of injury or health hazards (e.g. caused by electric shock).

The triangular warning symbol indicates important notes in this user manual which must be observed.

This symbol indicates special tips and notes on the operation of the device.

Lists

1. … 2. … Lists with a set order, given either in the text or warning notice.

• … • …

Lists without a set order, given either in the text or warning notice.

Intended use Only use the device for the purpose for which it was built and designed. Any other use is considered unintended.

Important safety information General Before using this device for the first time, please read the following instructions carefully and observe all warning information, even if you are familiar with the use of electronic devices.

All guarantee claims are invalid in the event of damage caused by non-compliance with this user manual. We cannot be held liable for resulting damage.

We cannot be held liable for material or personal damage caused by improper operation or non-compliance with the safety information. All guarantee claims are void in such cases.

Retain this handbook for future reference. If you sell or pass on the device to third parties, you must include these instructions with the device. The following safety information and hazard notes are not only intended to protect your health, but also to protect the device from damage. Please read the following points carefully:

4

English

Power supply • Only operate this device through a power source which supplies the mains power specified on

the type plate. If you are unsure of the power supply available to you, contact your energy provider.

• Disconnect the device from the power supply before carrying out maintenance or installation work.

• The device is only fully disconnected from the mains network when the power supply unit is removed.

• To fully disconnect the device completely from the mains, the mains plug must be withdrawn from the mains socket.

• In order to eliminate the risk of fire, the device's mains plug should always be disconnected from the mains socket, if the device is not being used for an extended period of time.

Overload/overvoltage • Prior to unstable weather and/or when there is a risk of lightning strike, disconnect the device

from the mains network or connect the device to a UPS. • Avoid overloading electrical sockets, extension cables and adapters, as this can result in fire or

electric shock. Cable • Always grasp all cables by the plug connector and do not pull the cable itself. • Never grasp the power cable with wet hands, as this can cause a short circuit or electric shock. • Do not place the device itself, items of furniture or other heavy objects on the cable and ensure

that it does not become kinked, especially at the connector plug and at the connection sockets. • Never tie a knot in the cable and do not bundle it together with other cables. • All cables should be laid so that they cannot be trodden on, or cause a hazard. • Damaged power cables can cause fire or electric shock. Check the power cable from time to

time. • Do not modify or manipulate the power cable or plug. • Only use adapter plugs or extension cables that conform to applicable safety standards, and do

not interfere with the mains or power cables. Children • Keep electrical devices out of reach of children. Never allow children to use electrical devices

unsupervised. Children may not always properly identify possible hazards. Small parts may be fatal if swallowed.

• Keep packaging film away from children. There is a risk of suffocation. • This device is not intended for children. If used incorrectly, parts under spring tension may fly out

and cause injury to children (e.g. to eyes). Surveillance • The use of surveillance equipment may be forbidden or regulated by law in some countries. • Before using this equipment, ensure that all of your surveillance activities are completely legal.

5

English

Installation location/operating environment Do not place any heavy objects on the device. The device is only designed for operation in spaces with appropriate temperatures or humidity (e.g. bathrooms), or excessive accumulation of dust. Please refer to the individual devices' technical data for more detailed information. Ensure that: • adequate ventilation is always guaranteed (do not place the device on a shelf, thick carpet, bed

or wherever ventilation slits may be covered. Always leave a 10 cm gap on all sides) • no direct sources of heat (e.g. radiators) can affect the device • interior devices are not exposed to direct sunlight or strong artificial light • the device is not in the immediate vicinity of magnetic fields (e.g. loudspeakers) • no naked lights (e.g. lit candles) are on, or next to the device • sprayed or dripping water is prevented from coming into contact with interior devices and caustic

fluids are avoided • the device is not operated in the vicinity of water, in particular, the device should never be

submerged (do not place objects containing fluids, e.g. vases or drinks, on or near the device) • no foreign bodies penetrate the device • the device is not exposed to wide temperature variations, as otherwise there may be

condensation from humidity causing electrical short circuits • the device is not exposed to excessive shock or vibration.

Unpacking the device Handle the device with extreme care when unpacking it. Packaging and packaging aids can be reused and, as far as possible, should be sent for recycling. We recommend the following: Paper, cardboard and corrugated cardboard as well as plastic packaging items should be placed in the appropriate recycling containers. If no such facility exists in the area, these materials should be put into the general household waste.

Warning If the original packaging has been damaged, start by inspecting the device. If the device shows signs of damage, return it in the original packaging and inform the delivery service.

Disposal

Devices displaying this symbol may not be disposed of with domestic waste. At the end of its service life, dispose of the product according to the applicable legal requirements. Please contact your dealer or dispose of the products at the local collection point for electronic waste.

6

English

Start-up • Observe all safety and operating instructions before operating the device for the first time.

Warning When installing the device in an existing video surveillance system, ensure that all devices have been disconnected from the mains power circuit and low-voltage circuit.

Warning Improper or unprofessional work on the mains network or domestic installations puts both you and others at risk. Connect the installations so that the mains power circuit and low-voltage circuit always run separately from each other. They should not be connected at any point or become connected as a result of a malfunction.

Care and maintenance Maintenance is necessary if the device has been damaged (e.g. damage to the power cable and plug, or the housing), or if liquids or foreign bodies have got into the interior of the device, or if it has been exposed to rain or damp, or if it does not work properly or has been dropped.

Maintenance • If smoke, unusual noises or smells develop, switch the device off immediately and unplug from

the socket. In such cases, the device should not be used until it has been inspected by a qualified technician.

• Have all maintenance tasks carried out by qualified technicians only. • Never open the housing on the device or accessories unless this is necessary. As there is

always a risk to life due to electric shock when the housing is open, only open the housing when the device is disconnected from the power source. With some devices, opening the device is unavoidable and permitted for the following purposes:

• Installing the device • Inserting a storage medium (SD card or hard disk drive) • Accessing essential functions (reset button or WPS button)

Cleaning • Only clean the device housing with a damp cloth. • Do not use solvents, white spirit, thinners etc., or any of the following substances:

Brine, insect spray, solvents containing chlorine or acids (ammonium chloride), or scouring powder.

• Rub the surface gently with the cotton cloth until it is completely dry.

The device operates with a dangerous voltage level. When conducting maintenance or cleaning work, disconnect the device from the mains.

7

English

Contents 1. Scope of delivery ..................................................................................................................................................................... 8

2. Description of the hardware ..................................................................................................................................................... 9

2.1. PPIC32020 ..................................................................................................................................................................... 9

2.2. PPIC32520 ..................................................................................................................................................................... 9

2.3. PPIC34520 ................................................................................................................................................................... 10

3. Description of the hardware functions .................................................................................................................................... 10

3.1. Status LEDs .................................................................................................................................................................. 10

3.2. Factory settings/reset .................................................................................................................................................... 11

4. Mounting/installation .............................................................................................................................................................. 12

4.1. PPIC32020 ................................................................................................................................................................... 12

4.2. PPIC32520 ................................................................................................................................................................... 12

4.3. PPIC34520 ................................................................................................................................................................... 13

5. App2Cam Plus: First access.................................................................................................................................................. 14

5.1. Download app ............................................................................................................................................................... 14

5.2. Setting up the camera ................................................................................................................................................... 14

5.2.1. Wi-Fi set-up (Android) ............................................................................................................................................. 14

5.2.2. Wi-Fi set-up (iOS) ................................................................................................................................................... 15

5.2.3. LAN set-up/Adding a camera that is already set-up ................................................................................................ 16

6. App2Cam Plus: Compatibility ................................................................................................................................................ 16

7. App2Cam Plus: Overview ...................................................................................................................................................... 17

7.1. Menu bar ....................................................................................................................................................................... 17

7.2. Camera bar ................................................................................................................................................................... 18

7.3. Info/app settings ............................................................................................................................................................ 18

8. App2Cam Plus: Live cast ...................................................................................................................................................... 19

8.1. Live cast functions......................................................................................................................................................... 19

8.2. Pan/tilt function ............................................................................................................................................................. 20

8.3. Active/inactive function .................................................................................................................................................. 20

8.4. Automatic adjustment of video quality ........................................................................................................................... 20

9. App2Cam Plus: Event list/playback ....................................................................................................................................... 22

9.1. Event list ....................................................................................................................................................................... 22

9.1.1. Event list functions .................................................................................................................................................. 22

9.1.2. Mode (iOS only) ...................................................................................................................................................... 22

9.2. Playback ....................................................................................................................................................................... 23

9.2.1. Playback functions .................................................................................................................................................. 23

10. Camera settings .................................................................................................................................................................. 24

10.1. Login details ................................................................................................................................................................ 24

10.2. Email notification ......................................................................................................................................................... 24

10.3. Open advanced settings .............................................................................................................................................. 24

10.4. Automatic log-in .......................................................................................................................................................... 25

11. Advanced camera settings .................................................................................................................................................. 25

11.1. Security settings .......................................................................................................................................................... 25

11.2. Video settings ............................................................................................................................................................. 26

11.3. Network settings ......................................................................................................................................................... 26

11.4. Motion detection settings ............................................................................................................................................. 27

11.5. Notification settings ..................................................................................................................................................... 27

11.6. Storage settings .......................................................................................................................................................... 27

11.7. Device settings ............................................................................................................................................................ 28

8

English

1. Scope of delivery

PPIC32020 • Wi-Fi pan/tilt camera • Power supply unit, 5 V DC/1.5 (EU, UK) • Network cable 1 m • Antenna • Ceiling bracket • Installation material • Quick guide

PPIC32520 • Wi-Fi pan/tilt outdoor camera • Power supply unit, 5 V DC/1.5 (EU, UK) • Network cable 1 m • Antenna • Wall bracket • Installation material • RJ45 coupling • Quick guide

PPIC34520 • Wi-Fi outdoor camera • Power supply unit, 5 V DC/1.5 (EU, UK) • Micro USB – RJ45 adapter • Antenna • Wall bracket • Installation material • Quick guide

9

English

2. Description of the hardware 2.1. PPIC32020

1 IR LEDs 2 Photo sensor

3 Lens 4 Microphone

5 Loudspeaker 6 LAN interface

7 Reset button 8 MicroSD card slot (max. 128 GB)

9 Power/Status LED 10 Power supply (5 V DC)

11 Antenna connection (RP-SMA)

2.2. PPIC32520

1 Internal microSD card slot 2 Internal reset button

3 Antenna connection (RP-SMA) 4 IR LEDs

5 Power/Status LED 6 Lens

7 Photo sensor 8 RJ45 (male) for LAN connection

9 Power supply (5 V DC) 10 MicroSD card slot (max. 128 GB)

11 Reset button

10

English

2.3. PPIC34520

1 Lens 2 Photo sensor

3 IR LEDs 4 Power and status LED

5 PIR sensor 6 Microphone

7 Antenna connection (RP-SMA) 8 Reset button

9 Internal microSD card slot (max.128 GB)

10 Internal micro USB interface for LAN connection

11 Power supply (5 V DC)

3. Description of the hardware functions 3.1. Status LEDs PPIC32020

LED Status Description

Power and status LED

Lights up green Camera connected to power Camera connected to network

Flashes green Camera set to the factory settings Camera firmware is being updated

Flashes green (2 x short & 1 x long)

Camera connected to power Camera sends its own access point out

Off Camera has no power supply Camera not connected to any network

11

English

PPIC32520

LED Status Description

Power and status LED

Lights up red Camera connected to power Camera connected to network

Flashes red

Camera set to the factory settings Camera firmware is being updated

Flashes red (2 x short & 1 x long)

Camera connected to power Camera sends its own access point out

Off Camera has no power supply Camera not connected to any network

PPIC34520

LED Status Description

Power LED

Lights up red Camera connected to power

Flashes red Camera set to the factory settings Camera firmware is being updated

Off Camera has no power supply

LED status

Lights up green Camera connected to network

Flashes green (2 x short & 1 x long)

Camera sends its own access point out

Off Camera not connected to any network

3.2. Factory settings/reset To reset the camera to its factory settings, press and hold the reset button for five seconds while the camera is operating.

12

English

4. Mounting/installation

IMPORTANT! The camera must be disconnected from the power supply during installation.

4.1. PPIC32020

Position the mount where you intend to install the camera. Mark up and drill the required holes. Next, use the screw anchors and screws provided to fasten the mount in place.

Attention! Make sure the alignment is correct. The 'LOCK' text must point in the direction of the scene to be monitored.

Use the small screws provided to fasten the base plate to the camera. Position the camera with the base plate on the mount in such a way that the arrow on the base plate is aligned with 'UNLOCK' on the mount. Next, fix the camera in place by turning the camera clockwise. The arrow must be aligned with 'LOCK'. 4.2. PPIC32520

If the camera is being installed on a roughcast wall, use the EVA foam provided and glue it to the back of the mount. First of all, disconnect the mount from the camera using the Allen key provided. Position the mount where you intend to install the camera. Mark up and drill the required holes. Insert the screw anchors provided. Reconnect the camera to the mount and feed the cable through the mount. Next, screw the camera and mount to the wall.

13

English

Cabling tips If you do not have the option of feeding the cable through the wall, the following alternatives are available:

1. Cable duct: Feed the cable downwards and out from the mount. Use a cable duct (width at least 40 mm, depth at least 30 mm) to protect the laid cable.

2. Surface-mounted box: Use a surface-mounted box (width and height at least 105 mm, depth at least 35 mm) and drill a hole into the box's cover so that the network cable and power cable can be fed into the surface-mounted box. Next, install the camera and mount on the cover of the surface-mounted box. Install the surface-mounted box in the desired installation location and screw the cover in place together with the camera.

4.3. PPIC34520

Position the mount where you intend to install the camera. Mark up and drill the required holes. Next, use the screw anchors and screws provided to fasten the mount in place. Next, install the camera on the mount by screwing the camera clockwise on to the thread. As soon as the camera is fully screwed into position, lock the camera further into place by tightening the wing nuts from underneath. For alignment purposes, loosen the wing screw at the side and align the camera in the desired position. Next, lock the camera into place once more by tightening the wing screw.

14

English

5. App2Cam Plus: First access 5.1. Download app Download the ‘App2Cam Plus’ app from the Google Play Store or Apple App Store before your initial access. 5.2. Setting up the camera Connect the camera to the power to begin set-up. If you would like to connect the camera to your home network (router) using the network cable, attach the network cable to the camera before connecting the camera to the power. The camera will be ready for set-up after approx. 60 seconds.

5.2.1. Wi-Fi set-up (Android)

Open the app and select option 1 to set up the camera on your Wi-Fi network. The app will automatically search for the camera's Wi-Fi access point. If multiple cameras are available at the same time during set-up, you will be shown a list of cameras. Select the required camera and press the arrow key to continue with installation. Before connecting the camera to the Wi-Fi, the app prompts you to change the security code on the camera, which is required to integrate the camera. Enter a security code and confirm it.

Note This security code should consist of at least eight characters and meet at least two or three of the following criteria:

• Uppercase letters (A–Z) • Lowercase letters (a–z) • Numbers (0–9)

Special characters are not allowed. The camera's standard security code '123456' is not permitted.

Select your home network Wi-Fi from the list of Wi-Fi networks, then enter the Wi-Fi password for your home network. Press 'OK' to set up the connection. The camera takes approx. 90 seconds to set up a connection with the Wi-Fi network. If the camera does not connect despite this set-up, reset the camera using the Reset button and repeat the above steps.

15

English

5.2.2. Wi-Fi set-up (iOS)

Before opening the app, go to your device's network settings and connect to your camera's Wi-Fi access point. This will have the name 'HD-XXXXXX'. The password for the camera's Wi-Fi access point: '12345678'. Once the connection is set up, open the app and select option 1 to set up the camera on your Wi-Fi network. Before connecting the camera to the Wi-Fi, the app prompts you to change the security code on the camera, which is required to integrate the camera. Enter a security code and confirm it.

Note This security code should consist of at least eight characters and meet at least two or three of the following criteria:

• Uppercase letters (A–Z) • Lowercase letters (a–z) • Numbers (0–9)

Special characters are not allowed. The camera's standard security code '123456' is not permitted.

Select your home network Wi-Fi from the list of Wi-Fi networks, then enter the Wi-Fi password for your home network. Press 'OK' to set up the connection. The camera takes approx. 90 seconds to set up a connection with the Wi-Fi network. If the camera does not connect despite this set-up, reset the camera using the Reset button and repeat the above steps.

16

English

5.2.3. LAN set-up/Adding a camera that is already set-up To set up a camera on a LAN network, use the network cable to connect the camera to your home network (router) before connecting the camera to the power.

Open the app and select option 2 to set up the camera on your LAN network. Enter a name for your camera. Use the 'Search' button to search for the camera on the network or enter the camera's DID manually. You now need to enter the camera's standard security code, '123456'. If the camera has already been set up, enter the security code previously assigned to the camera. Press the 'Save' button to add the camera.

Note If the camera has been added with the standard security code, '123456', this has to be changed to the camera's live cast the first time it is accessed.

Note If the camera has already been set up via another smartphone or user, select this method to add cameras that are already set up.

6. App2Cam Plus: Compatibility The App2Cam Plus is compatible with the following devices:

• PPIC32020 • PPIC32520 • PPIC34520 • TVAC19000A/B • TVAC19100A/B

Note Please note that some of the functions explained or demonstrated in these instructions may not be compatible with older generation cameras, or the camera functions may be different due to differences in the hardware.

17

English

7. App2Cam Plus: Overview

Note The screenshots and icons shown here are from the iOS app. The text, layout or functions may differ slightly from the Android app. If this is the case, this will be flagged up in the respective items or as an addendum – (iOS only) or (Android only).

In the overview, you can click on one of the preview images to open the camera's live cast. There are other functions you can use in the menu bar, camera bar and in the info/app setting.

7.1. Menu bar

Set up new camera/Add camera

Enable/disable camera bar

Start new attempt to connect cameras not yet connected

Open info/app settings

18

English

7.2. Camera bar

Open camera settings

Delete camera

Open event list

7.3. Info/app settings

Setup PIN Lock App PIN Menu in which you can assign an app pin. If enabled and assigned, this will be requested every time you open the app.

About About This section provides information about the current version of the app, data protection guidelines and API version.

User Manual Instructions You can call up the product page for the selected camera here. You can download the instructions from the download sector.

Video acceleration (Android only)

Enable/disable hardware decoding Hardware decoding is available for use on Android. Some Android devices have special hardware features which optimise the decoding of video streams. On older products or older Android devices, this may impact negatively on performance.

19

English

8. App2Cam Plus: Live cast In the live cast, a variety of different functions are available to you, depending on the model of camera. A full screen view, without functions, is shown in landscape mode.

8.1. Live cast functions

Create capture

Enable/disable audio output

Start manual recording

Open pan/tilt menu

Activate two-way communication

20

English

8.2. Pan/tilt function For pan/tilt cameras, you can either use a 'swipe' command to control the camera or long-press and release one point to bring the camera to that point.

Pan/tilt menu

/Save or call up point 1/home item

Save or call up point 2

Save or call up point 3

Calibration Camera calibrates itself once

Cancel Cancel

8.3. Active/inactive function Click the 'Arm' or 'Disarm' button to activate or deactivate the camera. You always have to enter the admin password.

Camera is switched on In its 'armed' state, the camera records when motion is detected and sends notifications (push)

Camera is switched off In its 'disarmed' state, the camera takes no further action when motion is detected.

8.4. Automatic adjustment of video quality If the quality of the connection to your camera gets worse and the video quality is set too high for the existing connection, the app will suggest automatically that the video quality be adjusted. Pressing the 'Adjust video quality' button will temporarily adjust the camera stream video quality to the quality of the current connection.

21

English

Stream indicators

CIF

VGA HD

Full HD

Display of the current stream's resolution

Direct Relay server

Display of the current connection status Direct: The Peer2Peer Server was able to set up a direct connection between your end device and the camera.

Relay server*: The Peer2Peer Server was unable to set up a direct connection. The video data is saved on the relay server for a short time so that your end device can get the data from the server. This causes a delay to the stream.

Low Normal Good

Display of the current assessment of the connection

xxx KB/s Display of the current kilobit consumption per second

*Note If the connection to your camera is always made via the relay server, please check the following settings:

• Check whether UPnP is enabled in your router • Check whether a hardware firewall or a software firewall is stopping a direct

connection • Check whether multiple 'hops' (router) are installed between the end device and

the internet.

22

English

9. App2Cam Plus: Event list/playback 9.1. Event list In this event list, you can set a start and end time. With this filter, the app will show you all recorded events in this period.

9.1.1. Event list functions

Create capture

Enable/disable audio output

Start manual recording

9.1.2. Mode (iOS only) By clicking on the 'Mode' button, you can select whether to view the files on the SD card in the set period or to view the files already downloaded to your end device in the set period.

23

English

9.2. Playback In the playback of results, a variety of different functions are available to you depending on the model of camera. A full screen view, without functions, is shown in landscape mode. The results usually need a short buffer time until the event can be played back.

Note During the playback of events, the event is automatically downloaded to your end device. For this reason, we recommend using Wi-Fi for the playback as much as possible to minimise the amount of data consumed.

9.2.1. Playback functions

Create capture

Enable/disable audio output

24

English

10. Camera settings

10.1. Login details You can change the camera's login details manually in the camera settings: Camera name: Change the camera name here. DID: Change the camera's DID manually. Security code: You can change the camera's security code here. You can use the 'Search' button to automatically replace the camera's DID with another camera found. Use the 'Cancel' button to discard the changes or save them with the 'Save' button. 10.2. Email notification Email notification: If email was set up in the camera's advanced settings, you can

now activate this here. 10.3. Open advanced settings The 'Settings' button opens the advanced settings. Use the standard password, '123456', the first time. The app then prompts you to change the admin password.

Note The admin password is a functional password and not a security password and is intended to help you to provide other people with a live cast and notifications from the cameras while protecting the advanced settings.

25

English

10.4. Automatic log-in When entering the admin password, you can use the 'Automatic log-in' button to save the admin password on your end device, meaning this does not need to be entered on your end device the next time you access the advanced settings. This does not apply when you are accessing the system from other end devices.

11. Advanced camera settings

Note Although the individual items have a different layout in Android, the functions are identical and available on both platforms.

11.1. Security settings Device security code: You can change the camera's security code here. Admin password: You can change the camera's admin password here. Disable automatic log-in: If automatic log-in has been enabled, you can disable it here.

26

English

11.2. Video settings Video quality: Standard Quality / Better Quality / Best Quality You can change the camera's preset video quality to VGA, HD

or Full HD here. The value set here has no effect on the recording, which is always made in Full HD.

Environment mode: Outdoor / Indoor 50 Hz / Indoor 60 Hz

Change the environment mode here to adjust the camera to the light conditions. For use indoors, adjust the frequency (50 Hz or 60 Hz) in line with the frequency on the mains network used. In European countries, the frequency is 50 Hz.

Image improvement: Levels 1–5 You can change the light enhancement here. A higher level will lighten the image more, a lower level less.

Screen orientation: Normal / Tilt / Reverse / Flip & Reverse Change the camera's display orientation here. Time stamp: Change the position of the time stamp by dragging and

dropping the time stamp into the desired corner. Change the colour of the time stamp by clicking on the desired colour. Remove the time stamp by clicking the image once. Changes will only take effect if saved. The 'Reload' button refreshes the preview.

11.3. Network settings Wi-Fi: Select your home Wi-Fi network from the list of Wi-Fi networks.

Enter the password for your Wi-Fi network and confirm with 'OK'.

The camera then sets up a new connection. If you have used

the network cable to connect your camera to your router, unplug this during the restart. If the camera cannot connect after approx. 90 seconds, restart the camera as your first course of action. If the camera still cannot connect, reconnect the camera with the network cable again and check the settings.

27

English

11.4. Motion detection settings Detection mode: Off / Software / PIR

You can change the detection mode here. If it is switched off, no recording or notification will take place if motion is detected. The choice between Software and PIR detection modes is only available if your camera has an integrated PIR sensor.

Information about the use of software detection The camera will detect differences in light between the individual pixels if software detection is in use. Please note that accidental deployment may occur if the camera is orientated towards a scene with fluctuations in light as standard (e.g. sunlight through a window).

Information about the use of PIR detection The camera detects differences in temperature using the integrated passive infrared sensor (PIR). Please note that accidental deployment may occur if the camera is orientated towards a scene with fluctuations in temperature as standard (e.g. windows, radiators, larger metal objects).

Sensitivity: You can change the sensitivity of the software detection for day

and night here. A high value will lead to detection in the event of minor changes, and a low value will trigger only in the event of more major changes to the camera image.

Motion screen: If you have enabled software detection, you can exclude

individual image sectors from the detection. Click the desired image sectors to do this. If the sector is black, no motion will be detected here.

11.5. Notification settings Notification: You can enable or disable push notifications here. Language notification: You can change the language of the push notifications here. Email: You can enter the email sender and receiver data here to set

up email notification. You can also enable email notification in the camera settings

for the respective camera (see item 10.1. ). 11.6. Storage settings SD card: Format the SD card here. Circular buffer: You can enable or disable the circular buffer here.

Note If the circular buffer is active, the camera transfers the earliest files when the SD card is full. If the circular buffer is deactivated, the camera stops recording once the SD card is full.

28

English

11.7. Device settings Camera name: You can change the camera's name here.

This is used on the time stamp and notifications. Time zone: You can adjust the time zone of the camera here. Summer time: You can enable or disable summer time.

If summer time is enabled, the time is put forward by one full hour.

Profile settings: You can save the camera's profile settings on your end device. You can then load the settings on to other cameras, or re-load them following a reset.

Device information: Information about the current firmware version / MCU version / storage capacity and free storage space on the SD card.