power suplies
-
Upload
cenkgezmis -
Category
Documents
-
view
223 -
download
0
description
Transcript of power suplies
-
Power supplies
EE328 Power Electronics
Assoc. Prof. Dr. Mutlu BOZTEPE
Ege University, Dept. of E&E
-
Outline of lecture
Introduction to power supplies
Modelling a power transformer
Analysis method of converters including a transformer
Steady-state analysis of
Flyback dc-dc converter
Forward dc-dc converter
Push-pull dc-dc converter
Full-bridge dc-dc converter
Half-bridge dc-dc converter
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 2
EE3
28
PO
WER
ELE
CTR
ON
ICS
-
Electrical isolation requirement
A basic disadvantage of the dc-dc converters (buck, boost etc.) is the electrical connection between the input and the output.
If the input supply is grounded, that same ground will be present on the output.
A way to isolate the output from the input electrically is with a transformer.
If the dc-dc converter has a first stage that rectifies an ac power source to dc, a transformer could be used on the ac side.
However, not all applications require ac to dc conversion as a first stage.
Moreover, a transformer operating at a low frequency (50 or 60 Hz) requires a large magnetic core and is therefore relatively large,
heavy, and expensive.
3 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Electrical isolation requirement
A more efficient method of providing electrical isolation between input and output of a dc-dc converter is to use a transformer in the
switching scheme.
The switching frequency is much greater than the ac power-source frequency, enabling the transformer to be small.
Additionally, the transformer turns ratio provides increased design flexibility in the overall relationship between the input and the output
of the converter.
With the use of multiple transformer windings, switching converters can be designed to provide multiple output voltages.
4 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Ideal transformer model
(a) Transformer;
(b) Ideal model
5 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Real transformer model
(c) Complete model
6 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Most used transformer model
The leakage inductances L1 and L2 are usually not crucial to the general
operation of the power electronics circuits described in this chapter, but they
are important when considering switching transients.
Magnetic core reset is important! The average voltage of Lm must be zero!
Otherwise the transformer saturates!
7 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
THE FLYBACK CONVERTER
8 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
Note the transformer
winding direction !!!
-
Assumptions for the analysis
1. The output capacitor is very large, resulting in a constant output
voltage Vo.
2. The circuit is operating in the steady state, implying that all voltages
an currents are periodic, beginning and ending at the same points
over one switching period.
3. The duty ratio of the switch is D, being closed for time DT and open
(1-D)T.
4. The switch and diode are ideal.
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 9
-
Analysis for the Switch ON
On the source side of the transformer
10 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Analysis for the Switch OFF
11 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Since the net change in inductor current must be zero over
one period for steady-state operation
Output voltage
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 12
-
Note that vsw, the voltage across
the open switch, is greater than
the source voltage.
Switch withstand voltage
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 13
-
Average magnetizing current
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 14
Substituting
Substituting
-
Min&max value of ILm
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 15
Continues current operation requires that ILm,min >0
At the boundary between CCM and DCM; ILm,min =0
-
The output configuration for the
flyback converter is the same as for
the buck-boost converter, so the
output ripple voltages for the two
converters are also the same.
Output voltage ripple
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 16
Buck-boost
-
EXAMPLE 7-1 Flyback Converter
17 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
EXAMPLE 7-2
Homework!!
Flyback converter design
18 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
FORWARD CONVERTER
Note that transformer
winding direction!!!
19 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Analysis for the Switch ON
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 20
-
Analysis for the Switch OFF
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 21
-
Output voltage
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 22
-
Transformer reset
23 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
When switch is on
-
Transformer reset
24 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
When switch is off
Slope for
-
Transformer reset
25 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
When switch is on When switch is off
By combining these two equations, time duration of Tx can be found as
-
Transformer reset
For example, if the ratio
N3/N1=1 (a common practice),
then the duty ratio D must be
less than 0.5
26 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
For proper resetting of transformer it should be t0
-
Some waveforms
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 27
-
28 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
Some waveforms
-
The circuit conguration on the output of the forward converter is the same as that for the buck converter, so the output voltage ripple based on an
ideal capacitance is also the same.
The equivalent series resistance of the capacitor often dominates the
output voltage ripple.
The peak-to-peak voltage variation due to the ESR is
EXAMPLE 7-4
AND 7-5 ARE
HOMEWORK
Output voltage ripple
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 29
-
THE PUSH-PULL
CONVERTER
30 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
THE PUSH-PULL
CONVERTER
31 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Sw1 is ON
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 32
-
Sw2 is ON
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 33
Same with the previous one
-
Both switches are OFF
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 34
-
Output voltage
the net change in inductor current over one period must be zero for steady state operation,
Solving for Vo
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 35
-
Ripple voltage on the output is derived in a manner similar to the buck converter.
The output ripple for the push-pull converter is
As with the other converters analyzed previously, the equivalent series resistance of the capacitor is usually responsible for most of
the voltage output ripple.
Recognizing that and using
EXAMPLE 7-6
ARE HOMEWORK
Output voltage ripple
EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014 36
-
THE FULL BRIDGE
CONVERTER
No reset winding!!!
37 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Note that the maximum voltage across an
open switch for the full-bridge converter is
Vs, rather than 2Vs as for the push-pull
and single-ended forward
converters.
38 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
THE HALF BRIDGE
CONVERTER
39 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
40 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Multiple output flyback
41 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014
-
Multiple output forward
42 EE328 Power Electronics, Dr. Mutlu Boztepe, Ege University, 2014