POWER AND DISTRIBUTION POWER DISTRIBUTION · 2009-08-21 · POWER DISTRIBUTION POWER AND...

POWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER DISTRIBUTIONPOWER AND DISTRIBUTION

Powerndistrib.eldon2008.indd 101 9/11/07 13:03:39

Adam Rowe

LARGE POWER 3

102

MAM

MCSL

MKSLMCF

108126

127120

5RPOWER AND DISTRIBUTION

IP55/NEMA 12Wallmounting enclosureSingle doorH: 800-1200 W: 600 D: 210

Low voltage switchgear enclosureH: 1800-2200 UW: 400-1200 UD: 600 U

IP55/NEMA12,13 IK10 Flange Mountdisconnectcombination enclosureH: 1800 - 2000W: 800 - 1000D: 400 - 600

Motor Control Center/Switchgear enclosureH: 200W: 600 - 1200D: 400

MAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMAMPOWER AND DISTRIBUTIONMAM

MCSL

MKSL


103

MKF

MCBJMCBA/

MCBA/V

122

114

116

5R POWER AND DISTRIBUTION

IP55/NEMA12,13 IK10 Flange mount disconnect compact enclosureH: 1600 - 2000W: 800 - 1000D: 500

IP30/NEMA1 Enclosure for ABB andJean Mueller cassettes H: 2000 W: 1000 - 1200D: 600

IP30/NEMA1Enclosure for verticalABB and Jean Muellercassettes H: 2000 W: 800-1000 D: 600

122compact enclosurecompact enclosureMKFMKFPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 IP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect compact enclosurePOWER AND DISTRIBUTIONcompact enclosurePOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONFlange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect compact enclosurePOWER AND DISTRIBUTIONcompact enclosurePOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect compact enclosurePOWER AND DISTRIBUTIONcompact enclosurePOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONMKFMKFPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect compact enclosurePOWER AND DISTRIBUTIONcompact enclosurePOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONFlange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect compact enclosurePOWER AND DISTRIBUTIONcompact enclosurePOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 POWER AND DISTRIBUTIONIP55/NEMA12,13 IK10 Flange mount disconnect POWER AND DISTRIBUTIONFlange mount disconnect compact enclosurePOWER AND DISTRIBUTIONcompact enclosurePOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONMKFPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION122POWER AND DISTRIBUTION122POWER AND DISTRIBUTIONPOWER AND DISTRIBUTIONPOWER AND DISTRIBUTION


104 Power and Distribution Visit our website at www.eldon.com

One of the main advantages of the Eldon Distribution Range is that you can design a system that perfectly matches your requirements

directly from the catalogue. Using standard components from our Multi-Mount® and Multi-Flex® ranges, you can build a complete

electrical distribution system for any typical lighting, heating or air conditioning application.

• Small secondary distribution panels using our Multi-Mount® range of mild steel wall-mounted enclosures, for

moulded-case circuit breakers (MCCB), modular circuit-breakers (MCB), or other modular components.

• Medium secondary distribution panels using our Multi-Flex® range of mild steel fl oor standing enclosures, for small

and large moulded-case circuit-breakers (MCCB), modular circuit-breakers (MCB), or other modular components.

• Main distribution assemblies for all type of circuit-breakers, air circuit-breakers (ACB), moulded-case circuit-

breakers (MCCB), modular circuit-breakers (MCB), or other modular components.

The Eldon Distribution Range is based on standard enclosures and accessories, which gives the fl exibility of integrating the control

and distribution sections into the same enclosure system.

The other advantage of the range is that it is a totally “open structure”, which means you can use any manufacturer of ACB, MCB,

MCCB or Busbars. The choice is yours!

External door/panels. Building process

The Eldon Distribution Range provides a complete solution for a variety of different applications

Partial door/panels,usable height H-200mm.

Plain front door

Transparent front door.

Moulded-case circuit-breakers(MCCB) with adjustablemounting plates.

Air circuit-breakers (ACB) with profi les.

Modular components with DIN profi les.

Busbar selection and position.

Front internal covers.

External door/panels.

Internal structure to fi x components:

Enclosure dimension according to:

Busbar supports.Components to be installed.

Building process

External confi guration

Plain door

Transparent door

Partial doors/panels

External door/panels.

Electrical characteristics

Rated operational voltage (Ue) 690V.

Rated current (In) up to 5000 A.

Short-circuit withstand up to 85 kA.

Degree of protection

Up to IP66

Up to IK10

External confi gurationType of installation

Wall mounting enclosures

Floor standing enclosures

ELDON DISTRIBUTION RANGE.ELDON DISTRIBUTION RANGE.

pag 104 PnD.indd 104 14/11/07 20:03:31

105

MultiMount

Product specifications, CAD drawings and information available on the website Power & Distribution

MAM / MAS

Wall mounting modular system Mounted enclosure for labour savings.

IP 55/NEMA 12

Technical data

Description: MAM enclosures are available in three different heights 800, 1000 and 1200 mm, with a width of 600 mm and a depth of 210 mm The front panels, blank or slotted, are available in multiples of 150 mm high. Each row can accept a maximum of 24 modules of 18 mm width.The delivery includes: MAS enclosure body without mounting plate, a glazed door ADT, a modular vertical support ACM and a combination of blank (MBP) and slotted (MCP) panels according to the enclosure height and the configuration.

You can find more information about these accesories in the Multimount accesories chapter. To build up your own configuration you can use the complete standard Multimount range and the P&D accessories.Protection: Complies with IP 55.Note: Pre-defined MAM configurations and catalogue references(The last digit of the catalogue reference indicates the number of slotted rows).

H W D Nº of slotted rows Nº of blank rows Total Nº of 18mm wide modules

Part No.

800 600 210 2 3 48 MAM080622R53 2 72 MAM080623R54 1 96 MAM080624R55 0 120 MAM080625R5



Chapter_03x_Power_x_Distribution_R5_2007_45297_0.fm Page 105 Monday, November 12, 2007 3:03 PM

106

MultiMount accessories

Power & Distribution Visit our website at www.eldon.com

ACM, Modular vertical support

Description: Support kit for the mounting of the modular panels and components by steps of 150 mm. A space for equipment of 46 mm high is provided. Independent of the depth of the enclosure, the system could be used in combination with glazed door and a mounting plate is still usable. 50 mm of space is provided for the equipment between the door and the panels. In order to allow an easy installation of the equipment and the wiring, the system can be assembled, fully equipped and pre-wired outside the enclosure, and then fitted into the enclosure. Cut-outs are provided on the sides of the vertical profiles for cable routing. The kit contains two vertical profiles, top and bottom blanking plates and fixing material.Material: 1.5 mm steel plate.structure powder paint, RAL 7035.Pack. quantity: 1 kit with fitting material.

H W Steps of 50mm

Nº of modules

Part No.

600 600 9 24 ACM06060R5800 9 35 ACM06080R5

800 600 15 24 ACM08060R5800 15 35 ACM08080R5

1000 600 18 24 ACM10060R5800 18 35 ACM10080R5

1200 600 21 24 ACM12060R5800 21 35 ACM12080R5

MCP, Modular slotted panel

Description: Front panel for modules. Provided with one DIN rail (PP 1535) per row for MCB (Mini Circuit Bracker).Material: 1mm steel plate.Finish: Structure powder paint, RAL 7035.Pack. quantity: 1 piece with mounting material.

H W Nº of modules

Nº of rows Part No.

150 600 24/1 1 MCP1506R5800 35/1 1 MCP1508R5

200 600 24/1 1 MCP2006R5800 35/1 1 MCP2008R5

300 600 48/2 2 MCP3006R5800 70/2 2 MCP3008R5

450 600 72/3 3 MCP4506R5800 105/3 3 MCP4508R5

600 600 96/4 4 MCP6006R5800 140/4 4 MCP6008R5

MIP, Modular instrumentation panel

Description: Front panel with cut outs for control meters and network analyser. To be mounted in a CMV profile for MF or in an ACM for a MM enclosure.Material: 1 mm steel plate.Finish: Structure powder paint, RAL 7035.Pack. quantity: 1 piece with mounting material.

W h Nº of cut outs

Dim Part No.

600 150 1 72 x 72 MIP1506-1PR52 72 x 72 MIP1506-2PR54 72 x 72 MIP1506-4PR52 92 x 92 MIP1506-2GR5


600 200 1 144 x 144 MIP2006-1SR5800 200 1 144 x 144 MIP2008-1SR5

CATALOGO 2008.book Page 106 Thursday, November 8, 2007 10:24 AM

Product specifications, CAD drawings and information available on the website. Power & Distribution 107

MultiMount accessoriesMBP, Modular blank panel

Description: Front blank panel to cover unused space or to mount special equipment. Panels are with flanged top and bottom to provide extra stiffness.Material: 1.5 mm steel plate.Finish: Structure powder paint, RAL 7035.Pack. quantity: 1 piece with mounting material.

H: MCCB in horizontal assembly, V: MCCB in vertical assembly.

W H MCCB Steps of 50mm

Part No.

600 50 1 MBP0506R5800 50 1 MBP0508R5600 100 2 MBP1006R5800 100 2 MBP1008R5600 150 3 MBP1506R5800 150 3 MBP1508R5600 200 250A (H) 4 MBP2006R5800 200 250A (H) 4 MBP2008R5600 300 250A (V) 6 MBP3006R5800 300 250A (V) 6 MBP3008R5600 450 400A (V) 9 MBP4506R5800 450 400A (V) 9 MBP4508R5600 600 800A (V) 12 MBP6006R5800 600 800A (V) 12 MBP6008R5600 900 1600A (V) 18 MBP9006R5800 900 2500A (V) 18 MBP9008R5

Description: Allowing fixing of MCCB up to 400 A of any manufacturer. Requires MD depth adjust kit (sold separetely).Material: 2 mm galvanised steel plate.Pack. quantity: 1 piece with fitting material.


W h MCCB Steps of 50mm

Part No.

600 194 125/160/250A (H) 4 AMM604244 125/160/250A (V) 6 AMM606294 400A (V) 9 AMM609


AMM, Modular system mounting plate

MD, Modular system depth adjust Kit

Description: Mounted on to the back of the ACM or CMV modular system frames, allowing the fixing of the AMM mounting plate. The mounting plate is adjustable in depth between 60 and 150 mm from the front covers.Material: 2.0 mm galvanised steel.Pack. quantity: 4 pieces with fitting material.

Part No.

MD4


Power & Distribution Visit our website at www.eldon.com108

MultiFlex

MCSL P&D

Motor Control Center/Switchgear enclosures Based on the well-proven Multi-Flex MCS design, the MCSL offers a modular solution for your low voltage switchgear requirements. Numerous accessories allow the installation of standard industrial switchgear components.

Technical data

Description: Variation of a standard Multi-Flex MCS enclosure. For technical and dimensional information see Floor standing section.

Finish: Structured powder paint RAL7035Delivery: Frame with rear and roof panel.

H W D Steps of 50mm Part No.

1800 400 600 32 MCSL18046R5600 600 32 MCSL18066R5800 600 32 MCSL18086R5

1000 600 32 MCSL18106R51200 600 32 MCSL18126R5


1000 600 36 MCSL20106R51200 600 36 MCSL20126R5


1000 600 40 MCSL22106R51200 600 40 MCSL22126R5


109

MultiFlex


MKSL P&D

Motor Control Center/Switchgear enclosure Based on the MultiFlex MKS design, the MKSL offers a modular solution for low voltage switchgear requirements. Numerous accessories allow the installation of standard industrial switchgear components.

Technical data

Material: Variation of a standard MultiFlex MKS enclosure. for technical and dimensional information see Floor standing section.Finish: Structure powder paint RAL7035

Delivery: Body with rear panel and roof panel. Delivered on a pallet with width identical with the enclosure to allow suiting without removal. All packing material recyclable.

H W D Steps of 50mm Part No.

2000 600 400 36 MKSL20064R5800 400 36 MKSL20084R5

1000 400 36 MKSL20104R51200 400 36 MKSL20124R5


110

MultiFlex accessories


CMV, Modular system support

Description: Support frame for mounting the modular panels and components by steps of 150 mm (a space for equipment of 46 mm high is provided). By using PP 0735 DIN rails 54 mm can be obtained. The mounting plate can still be used and there is 80 mm of space between standard or glazed doors and the fitted panels for protruding equipment. The frame can be assembled. fully equipped and pre-wired outside the enclosure. and then fitted into the enclosure. Cut-outs are provided on the sides of the vertical support for cable routing.Material: 1.5 mm steel plate in structure powder paint. RAL 7035.Pack. quantity: 2 vertical profiles, top & bottom plates.

H W Steps of 50mm

Part No.

1800 600 32 CMV1806R5800 32 CMV1808R5

2000 600 36 CMV2006R5800 36 CMV2008R5

MIP, Modular instrumentation panel

Description: Front panel with cut outs for control meters and network analyser. To be mounted in a CMV profile for MF or in an ACM for a MM enclosure.Material: 1 mm steel plate.Finish: Structure powder paint, RAL 7035.Pack. quantity: 1 piece with mounting material.

W h Nº of cut outs

Dim Part No.



600 200 1 144 x 144 MIP2006-1SR5800 200 1 144 x 144 MIP2008-1SR5

MCP, Modular slotted panel

Description: Front panel for modules. Provided with one DIN rail (PP 1535) per row for MCB (Mini Circuit Bracker).Material: 1mm steel plate.Finish: Structure powder paint, RAL 7035.Pack. quantity: 1 piece with mounting material.

H W Nº of modules

Nº of rows

Part No.

150 600 24/1 1 MCP1506R5800 35/1 1 MCP1508R5

200 600 24/1 1 MCP2006R5800 35/1 1 MCP2008R5

300 600 48/2 2 MCP3006R5800 70/2 2 MCP3008R5

450 600 72/3 3 MCP4506R5800 105/3 3 MCP4508R5

600 600 96/4 4 MCP6006R5800 140/4 4 MCP6008R5



MultiFlex accessoriesMBP, Modular blank panel

Description: Front blank panel to cover unused space or to mount special equipment. Panels are with flanged top and bottom to provide extra stiffness.Material: 1.5 mm steel plate.Finish: Structure powder paint, RAL 7035.Pack. quantity: 1 piece with mounting material.


W H MCCB Steps of 50mm

Part No.

600 50 1 MBP0506R5800 50 1 MBP0508R5600 100 2 MBP1006R5800 100 2 MBP1008R5600 150 3 MBP1506R5800 150 3 MBP1508R5600 200 250A (H) 4 MBP2006R5800 200 250A (H) 4 MBP2008R5600 300 250A (V) 6 MBP3006R5800 300 250A (V) 6 MBP3008R5600 450 400A (V) 9 MBP4506R5800 450 400A (V) 9 MBP4508R5600 600 800A (V) 12 MBP6006R5800 600 800A (V) 12 MBP6008R5600 900 1600A (V) 18 MBP9006R5800 900 2500A (V) 18 MBP9008R5

MD, Modular system depth adjust Kit

Description: Mounted on to the back of the ACM or CMV modular system frames, allowing the fixing of the AMM mounting plate. The mounting plate is adjustable in depth between 60 and 150 mm from the front covers.Material: 2.0 mm galvanised steel.Pack. quantity: 4 pieces with fitting material.

Part No.

MD4

AMM, Modular system mounting plate

Description: Allowing fixing of MCCB up to 400 A of any manufacturer. Requires MD depth adjust kit (sold separetely).Material: 2 mm galvanised steel plate.Pack. quantity: 1 piece with fitting material.


W h MCCB Steps of 50mm

Part No.



MPV, Depth adjustment kit

Description: Fitted in the vertical profiles of the enclosures MCS and MKS, allows the fixing of universal MCCB larger than 400 A of any manufacturer.Material: 2.5 galvanised steel.Pack. quantity: 4 pieces in depth and 2 in width.

W D For amp. Part No.

600 400 600 - 2500 MPV604500 600 - 2500 MPV605600 600 - 2500 MPV606

800 400 600 - 2500 MPV804500 600 - 2500 MPV805600 600 - 2500 MPV806

CATALOGO 2008.book 1 Thursday, November 8, 2007 10:24 AM

112



CLPK, Click-in profile

Description: Universal profile for both depth and width fitting on the 25 mm DIN hole pattern of the enclosure frame or in combination with the VB profiles. The 75 mm wide profile is equipped with three rows of holes of which one is turned 90 degrees. This makes it possible to mount the CLPF profiles in both directions. The CLPK can be secured by the use of self tapping screws.Material: 1.5 mm zinc plated steel.Pack. quantity: 4 profiles

Add CLPF profiles for almost unlimited mounting options.

For enclosureW/D Part No.400 CLPK400500 CLPK500600 CLPK600800 CLPK800

1000 CLPK10001200 CLPK1200

MPP, Partial height mounting plate

Doors and panels: Mounted directly on the enclosure frame or onto the click-in profiles (CLPK). Special design of the bracket allows one man mounting. Can be mounted in any height or depth position within the 25 mm hole pattern. Appropriate sizes can also be used in the sides of the enclosure.Material: 3 mm galvanised steel.Pack. quantity: 1 plate with mounting material.

Add CLPK for depth adjustment.

For H/W W/H h/w w/h Part No.400 400 294 294 MPP0404

500 294 394 MPP0405600 400 494 294 MPP0604

500 494 394 MPP0605800 494 694 MPP0608

1000 494 894 MPP0610800 400 694 294 MPP0804

800 694 694 MPP08081000 400 894 294 MPP1004

800 894 694 MPP10081200 400 1094 294 MPP1204

600 1094 494 MPP1206

CLPF, Mounting profile

Description: The CLPF profile system is a 40 mm wide and 25 mm high profile, which can be mounted in all directions in the enclosure frame. It can also be used in combination with the CLPK and the VB profiles. By turning the profile it can be used as a standard CP20/40 profile in combination with GLM 40/6 sliding nut, to mount installation material which needs adjusting in depth. The profiles, when mounted onto the enclosure frame are flush with the enclosure profiles. Two rows of hole patterns for cage nut fixing and self tapping screws are provided. For 90 mm wide profiles two profiles can be mounted next to each other.Material: Zinc plated steel.Pack. quantity: 4 profiles including fixing material.

For enclosureH/W W/D Part No.

400 400 CLPF400500 500 CLPF500600 600 CLPF600800 800 CLPF800

1000 1000 CLPF10001200 1200 CLPF12001600 CLPF16001800 CLPF18002000 CLPF20002200 CLPF2200

GLM, Sliding nuts for mounting rails

Material: Zinc plated steel.Pack. quantity: 50

Thread Part No.

M6 GLM20-6PM8 GLM20-8PM6 GLM40-6PM8 GLM40-8P

Profile Application


113

Power and DistributionVisit our website at www.eldon.com

Values of rated diversity factor (according to EN60439-1 4.7)

Number of main circuits Rated diversity factor

2 and 3 0,9

4 and 5 0,8

6 to 9 inclusive 0,7

10 (and above) 0,6

Busbar Section (mm)

Admissible current ( A )

50 K 30 K

1 bar per phase 2 bar per phase 3 bar per phase 1 bar per phase 2 bar per phase 3 bar per phase

25 x 5 433 776 327 586

30 x 5 502 890 379 672

40 x 5 639 1108 482 836

50 x 5 772 1317 583 994

60 x 5 912 1524 688 1150

63 x 5 951 1586 718 1197

80 x 5 1173 1921 885 1450

30 x 10 756 1300 1701 573 986 1289

40 x 10 944 1624 2124 715 1230 1609

50 x 10 1129 2001 2703 852 1510 2040

63 x 10 1305 2279 3048 985 1720 2300

80 x 10 1643 2796 3697 1240 2110 2790

100 x 10 1974 3286 4320 1490 2480 3260

120 x 10 2306 3790 4956 1740 2860 3740

According to EN 60439-1:1999 (“European standard for Low-voltage switchgear and controlgear assemblies”, Busbar is a low-impedance conductor to which several electric circuits can be separately connected. In the assemblies it´s usual that we have a main busbar (to which one or several distribution busbars and/or incoming and outgoing units can be connected) and several distribution busbars (which is connected to a main busbar and from which outgoing units are supplied).

In the design of the busbars we need to take in consideration the following values.

1. Thermal current:

a. The main busbar must be designed for its rated current, and each distribution busbar must be designed for the sum of the rated current of the outgoing circuits multiplied by the rated diversity factor (table1).

b. To fi nd out the cross-section and number of bars per phase we can use table 2, and we need to take into consideration:

i. Ambient temperature inside the enclosure.ii. Busbar material, these values are for Copper bars Cu-ETP (Cu/a1).iii. The way the busbars are positioned, these values are for rectangular bars standing on their edge.

2. Short circuit currents.

Following the specifi c data table for each busbar support, and according to the following values, we will defi ne the type of busbar support and the space between them.

i. Rated conditional short-circuit current, Icc.ii. Rated peak withstand current, Ipk (calculated according to EN 60439-1 7.5.3).iii. Busbar section.

3. Clearence and creepage distances. According to EN 60439-1 7.1.2 for busbars the creepage distances and the clearances or impulse withstand voltages shall at least comply

with those specifi ed for the apparatus with which they are directly associated.a. Clearances from live parts to those parts intended to be earthed and between poles shall withstand the rated impulse withstand

voltage.b. Creepage distances shall correspond to a pollution degree and to the corresponding material group, which in this case are,

pollution degree 3 and Material group II.

BUSBAR DESIGN

Table 1

Table 2

Busbar

pagina 113.indd 113 14/11/07 19:47:01

114

338-390

65 65 65290

325-377

65

H25 80

5/6 35

6.5 x 23 mm

338-390

290

325-377

60

H25 80

338-390

65 65 65290

325-377

65

H25 80

5/6 35

6.5 x 23 mm

338-390

290

325-377

60

H25 80

Power and Distribution Visit our website at www.eldon.com

Description: Busbar support up to 1600A to be mounted hori-zontally or vertically. Mounts directly to the enclosure frame or with help of CLPF profiles. Available in single and double bar per phase for bar thickness 5mm and only single bar per phase for bar thickness 10mm, and width from 25 to 80mm. The ECBS 1/10 can be used for ABB or JM cassettes as it has a 60mm pitch.

Working temperature: -40ºC up to 130ºC Material: Reinforced polyamide and steel. Halogen free.Delivery: Busbar support with mounting material.

Part No.

ECBS205TN

ECBS110TN

Maximun distance between supports (mm)

Ipk (kA) 11 24 48 63 82 114 145 152 165

Icc (kA) 6,5 12 23 30 39 52 66 69 75

1 barper

phase

25 x 5 1000 527 261 200 154 110 - - -

30 x 5 1000 578 286 219 169 120 - - -

40 x 5 1000 667 331 253 195 139 108 - -

50 x 5 1000 746 370 284 218 156 108 - -

63 x 5 1000 837 416 318 245 175 108 - -

80 x 5 1000 944 468 359 276 175 108 - -

2 barsper

phase

25 x 5 1000 746 370 284 218 156 - - -

30 x 5 1000 817 406 311 239 171 108 - -

40 x 5 1000 944 468 359 276 175 108 - -

50 x 5 1000 1000 524 401 309 175 108 - -

63 x 5 1000 1000 588 451 342 175 108 - -

80 x 5 1000 1000 663 508 342 175 108 - -


Ipk (kA) 11 24 48 63 82 114 145 152 165

Icc (kA) 6,5 12 23 30 39 52 66 69 75

1 barper

phase

25 x 10 1000 1000 503 386 296 161 100 - -

30 x 10 1000 1000 551 422 315 161 100 - -

40 x 10 1000 1000 637 488 315 161 100 - -

50 x 10 1000 1000 712 534 315 161 100 - -

60 x 10 1000 1000 780 534 315 161 100 - -

80 x 10 1000 1000 901 534 315 161 100 - -

ECBS205TN

ECBS205TN

ECBS110TN

ECBS110TN

BusbarECBS, Compact Busbar support

pagina 113.indd 114 14/11/07 19:47:25

115

380-610

360-590300

10H30 120

70 70 70

10585-895

560-865

281

480

H30 120

110 110 110

10

480110 110 110

560-865

H30 120

585-895281

380-610

360-590300

10H30 120

70 70 70

10585-895

560-865

281

480

H30 120

110 110 110

10

480110 110 110

560-865

H30 120

585-895281

380-610

360-590300

10H30 120

70 70 70

10585-895

560-865

281

480

H30 120

110 110 110

10

480110 110 110

560-865

H30 120

585-895281

Power and DistributionVisit our website at www.eldon.com

Description: Busbar support up to 4500A to be mounted horizontally or vertically. Mounts directly to the enclosure frame or with help of CLPF profiles. Available in one/two/three bars per phase for bar thickness 10mm, and width from 30 to 120mm.

Working temperature: -40ºC up to 130ºC Material: Reinforced polyamide and steel. Halogen free.Delivery: Busbar support with mounting material.

Part No.

EUBS110TN

EUBS210TN

EUBS310TN


Ipk (kA) 24 48 63 82 114 145 152 165 187 209 231

Icc (kA) 12 23 30 39 52 66 69 75 85 95 105

1 barper

phase

30 x 10 1000 747 572 440 315 248 237 218 192 172 155

40 x 10 1000 863 661 508 364 286 274 252 222 197 161

50 x 10 1000 965 739 568 407 320 306 282 247 197 161

60 x 10 1000 1000 810 623 446 351 336 309 247 197 161

80 x 10 1000 1000 935 719 515 405 375 317 247 197 161

100 x 10 1000 1000 1000 804 576 410 375 317 247 197 161

120 x 10 1000 1000 1000 881 631 410 375 317 247 197 161

2 barsper

phase

30 x 10 1000 1000 810 623 446 351 336 309 272 243 220

40 x 10 1000 1000 935 719 515 405 388 357 314 281 237

50 x 10 1000 1000 1000 804 576 453 433 399 352 290 237

60 x 10 1000 1000 1000 881 631 497 475 437 362 290 237

80 x 10 1000 1000 1000 1000 728 574 549 466 362 290 237

100 x 10 1000 1000 1000 1000 814 601 550 466 362 290 237

120 x 10 1000 1000 1000 1000 892 601 550 466 362 290 237


Ipk (kA) 24 48 63 82 114 145 152 165 187 209

Icc (kA) 12 23 30 39 52 66 69 75 85 95

1 barper

phase

30 x 10 1000 596 456 351 251 197 189 161 125 100

40 x 10 1000 688 527 405 290 208 190 161 125 100

50 x 10 1000 769 590 453 324 208 190 161 125 100

60 x 10 1000 843 646 497 336 208 190 161 125 100

80 x 10 1000 973 746 574 336 208 190 161 125 100

100 x 10 1000 1000 834 641 336 208 190 161 125 100

120 x 10 1000 1000 914 656 336 208 190 161 125 100


Ipk (kA) 24 48 63 82 114 145 152 165 187 209 231

Icc (kA) 12 23 30 39 52 66 69 75 85 95 105

10 mm

30 x 10 1000 747 572 440 315 248 237 218 192 172 155

40 x 10 1000 863 661 508 364 286 274 252 222 199 172

50 x 10 1000 965 739 568 407 320 306 282 248 210 172

60 x 10 1000 1000 810 623 446 351 336 309 263 210 172

80 x 10 1000 1000 935 719 515 405 388 338 263 210 172

100 x 10 1000 1000 1000 804 576 437 400 338 263 210 172

120 x 10 1000 1000 1000 881 631 437 400 338 263 210 172

10 mm

30 x 10 1000 1000 810 623 446 351 336 309 272 243 205

40 x 10 1000 1000 935 719 515 405 388 357 313 250 205

50 x 10 1000 1000 1000 804 576 453 433 399 313 250 205

60 x 10 1000 1000 1000 881 631 497 475 402 313 250 205

80 x 10 1000 1000 1000 1000 728 519 475 402 313 250 205

100 x 10 1000 1000 1000 1000 814 519 475 402 313 250 205

120 x 10 1000 1000 1000 1000 837 519 475 402 313 250 205

10 mm

30 x 10 1000 1000 992 763 546 430 411 378 313 250 205

40 x 10 1000 1000 1000 881 631 497 475 402 313 250 205

50 x 10 1000 1000 1000 985 705 519 475 402 313 250 205

60 x 10 1000 1000 1000 1000 772 519 475 402 313 250 205

80 x 10 1000 1000 1000 1000 837 519 475 402 313 250 205

100 x 10 1000 1000 1000 1000 837 519 475 402 313 250 205

120 x 10 1000 1000 1000 1000 837 519 475 402 313 250 205

EUBS110TN

EUBS110TN

EUBS210TN

EUBS310TN

EUBS210TN

EUBS310TN

BusbarEUBS, Compact Busbar support

pagina 113.indd 115 14/11/07 19:47:51

116



MCU P&D, Top cabling frame

Description: For cable entry and routing or for installation of a power distribution system. Fixed to the top of the enclosure by four M12 screws. The enclosure roof plate (CCR) can be used to close the top. For lifting a 200 mm high MCU together with an enclosure a separate lifting kit (MCUK) is needed.Material Frame in 1.75 mm steel plate, panels in 1.5 mm steel plate.Finish: Structure powder paint RAL 7035.Protection: IP 41Delivery: 1 piece with front and back panels including mounting material (without roof plate).

H W D Part No.

200 400 600 MCU2046R5600 600 MCU2066R5800 600 MCU2086R5

MCU2106R5200 1200 600 MCU2126R5

MCUP P&D, Side panels

Description: For covering the sides of the top cabling frame. Fixed by 4 screws.Material: 1.5 mm steel plate.Finish: Structure powder paint RAL 7035Pack. quantity: 2 panels with mounting material.

H D Part No.

200 600 MCUP206R5

MCUK, Lifting kit

Description: For lifting the enclosure together with the top cable frame of 200 mm high. Mounted directly into the enclosure frame and therefore releasing the MCU from any strain. 300 mm high MCU' s must be lifted separately.Pack. quantity: 4 spindles with lifting eyes according to DIN 580 lifting instructions.

Part No.

MCUK04

PCU P&D, Cable wiring & Busbar plinth

Description: For fixing and routing of cables or mounting of busbar holders e.g. Erico, Ter-Mate. Identical hole pattern to the enclosure frame makes all relevant accessories (e.g. CLPF, CLPK, etc) possible to mount. Fixed to the base of the enclosure by M12 screws (provided).Material: Frame in 1.75 mm steel plate, panels in 1.5 mm steel plate.Finish: Structure powder paint RAL 7035Protection: IP41/NEMA 1Delivery: 1 piece with front and back cover plates with mounting material. PCUP side panels need to be ordered separately.

For closing the sides add side panels PCUP.

H W D Part No.

200 400 600 PCU2046R5600 600 PCU2066R5800 600 PCU2086R5

1000 600 PCU2106R51200 600 PCU2126R5

300 400 600 PCU3046R5600 600 PCU3066R5800 600 PCU3086R5

1000 600 PCU3106R51200 600 PCU3126R5

PCUP P&D, Side panels

Description: For covering the sides of the cable wiring plinth PCU. Fixed by screws.Material: 1.5 mm steel plate.Finish: Structure powder paint RAL 7035Pack. quantity: 2 panels with mounting material.

H D Part No.

200 600 PCUP206R5300 600 PCUP306R5



MultiFlex accessoriesCCI, Internal baying brackets

Description: Brackets provide a rigid reinforcement of the enclosure assembly. Automatic spacing between the enclosures is assured.Material: 3 mm zinc plated steel.Pack. quantity: 6 brackets with mounting material.

Part No.

CCI06

CCM, Internal corner baying kit

Description: For extra support when bayed enclosures are fully equipped and require lifting. Can be used together with SPD separation plates.Material: 3 mm zinc plated steel.Pack. quantity: 4 brackets with mounting material.

Part No.

CCM04

CCE, External baying brackets

Description: Brackets mounted on the outside hole pattern of the frame ensuring a strong and 3 dimensional alignment of the bayed enclosures with "auto spacer" function. This method of baying enclosures has also the advantage of realising a direct earthing connection between the enclosure frames.Material: 3 mm zinc plated steel.Pack. quantity: 6 brackets with mounting material.

Part No.

CCE06

SPM P&D, Side panels

Description: Easy one man assembly. Sealed by an extruded, one piece polyurethane gasket and mounted with 8 screws. Can be replaced by the side door DS.Material 1.5 mm steel plate.Finish: Structure powder paint, RAL 7035Protection: IP 56/NEMA 4, 12, 13.Pack. quantity: 2 panels with mounting material.

H D Part No.

1800 400 SPM1804R5500 SPM1805R5600 SPM1806R5800 SPM1808R5

2000 400 SPM2004R5500 SPM2005R5600 SPM2006R5800 SPM2008R5

2200 600 SPM2206R5800 SPM2208R5900 SPM2209R5


118



D P&D, Plain doors

Description: Standard door equipped with DIN 3 mm lock system and door frame. Door accessory kit DMK (hinges, rod catches) to be ordered separately. Allows all the options of the locking programme and 180º hinges.Maximum load: 800NMaterial: 2 mm steel plate.Finish: Structure powder paint RAL 7035.Pack. quantity: 1 piece

If no door was fitted previously use hinge kit DMK01.

H W Part No.

1100 600 D1106R51400 800 D1408R51600 600 D1606R51800 600 D1806R5

800 D1808R52000 600 D2006R5

700 D2007R5800 D2008R5

2200 600 D2206R5800 D2208R5

DGC P&D, Glazed door Description: Standard door with fitted clear safety glass to view the inside of the enclosure. Equipped with DIN 3 mm lock system and door frame. Allows all options of the locking programme. Use hinge kit DMK if not for replacement of standard door.Material: Frame: 2 mm steel plate. Viewing area: 4 mm clear safety glass.Finish: Structure powder paint. RAL 7035.Protection: IP55/NEMA12, IK10Pack. quantity: 1 piece

If no door was fitted previously use hinge kit DMK01.

H W h w Part No.

1100 600 876 415 DGC1106R51400 800 1176 615 DGC1408R51600 600 1376 415 DGC1606R51800 600 1576 415 DGC1806R5

800 1576 615 DGC1808R52000 600 1776 415 DGC2006R5

800 1776 615 DGC2008R52200 600 1976 415 DGC2206R5

800 1976 615 DGC2208R5

DMK, Door mounting kit

Description: Required when fitting a door. Only needed when there was no door mounted previously, for example when replacing a back panel for a door.Pack. quantity: 4 standard hinges. 4 rod catches and mounting material.

Description Part No.

for single door enclosures DMK01for double door enclosures DMK02

DPB, Vertical front panel

Description: In order to cover vertical busbar space. Used in combination with CDV.Material: 2 mm steel plate.Finish: Structure powder paint, RAL 7035.Protection: IP 44. IP 21 delivered without gasket.Pack. quantity: 1 panel with mounting material.

H W Part No.

1800 200 DPB18002R52000 200 DPB20002R52200 200 DPB22002R5



MultiFlex accessoriesUseful height

H: Enclosure heighth: Useful height to be covered with: DP, Partial door, DPP, Partial panel, DPA, Cable door

DPA, Cable space door

Description: To close a vertical cable section. Used in combination with CDV. In order to close the the front, top and bottom panels DPC are required.Material: 2 mm steel plate.Finish: Finish structure powder paint, RAL 7035.Protection: Protection IP 44. For IP 21 delivered without gasket.Pack. quantity: 1 door with hinges and 3 DIN 3 mm, locks.

H W Part No.

1400 400 DPA1404R51600 400 DPA1604R51800 400 DPA1804R5

600 DPA1806R52000 400 DPA2004R5

600 DPA2006R5

DPC, Top and bottom panels

Description: Required to cover the remaining space at the top and bottom. Used in combination with the partial doors (DP) and dividers CDH, CDHK.Material: 2 mm steel plate.Finish: Structure powder paint RAL 7035.Protection: IP 44. For IP 21 delivered without gasket.Pack. quantity: 2 panels with mounting material.

Note: The DPC cover 200mm in height of the enclosure. So for a 2000mm high enclosure when DPC is used, there is 1800mm space left for partial doors/panels.

Height top W Height bottom

Part No.

70 400 100 DPC0714R5600 100 DPC0716R5800 100 DPC0718R5

DPCV, Ventilated top and bottom panels

Description: Required to cover the remaining space at the top and bottom. With ventilation slots for added heat dissipation in switchgear enclosures. Used in combination with the partial doors (DP) and dividers CDH, CDHK.Material: 1.5 mm steel plate.Finish: Structure powder paint RAL 7035.Protection: IP 20. Delivered without gasket.Pack. quantity: 2 panels with mounting material.

Note: The DPCV covers 200mm in height of the enclosure. So for a 2000mm high enclosure when DPC is used, there is 1800mm space left for partial doors/panels.

H W Part No.

100+100 400 DPCV0714R5600 DPCV0716R5800 DPCV0718R5

Chapter_03x_Power_x_Distribution_R5_2007_45297_3.fm Page 119 Wednesday, November 14, 2007 5:24 PM

120



DP, Partial doors

Description: To divide the enclosure front into sections when used in conjunction with the horizontal divider CDH on CDHK. Equipped with 3 mm DIN lock (1 lock up to 400 mm over 400 mm height 2 locks).Material: 2 mm steel plate.Finish: Structure powder paint. RAL 7035.Protection: IP 44Pack. quantity: 1 door with hinges, locks and mounting material.

Add CDH for MCS and CDHK for MKS enclosures. Use DPC for top and bottom panels.

H W Part No.

150 400 DP01504R5600 DP01506R5

200 400 DP02004R5600 DP02006R5

250 400 DP02504R5600 DP02506R5

300 400 DP03004R5600 DP03006R5800 DP03008R5

400 400 DP04004R5600 DP04006R5800 DP04008R5

500 400 DP05004R5600 DP05006R5

600 400 DP06004R5600 DP06006R5800 DP06008R5

800 600 DP08006R5800 DP08008R5

1000 600 DP10006R5

DPP, Partial panel

Description: In combination with the horizontal divider CDH (MCS) on CDHK (MKS). Provide the partitioning of the front of the enclosure when a door is not required.Material: 2 mm steel plate.Finish: Structure powder paint, RAL 7035.Protection: IP 44Pack. quantity: 1 panel with mounting material.

Add CDH for MCS and CDHK for MKS enclosures. Use DPC for top and bottom panels.

H W Part No.

100 400 DPP01004R5150 400 DPP01504R5

600 DPP01506R5200 400 DPP02004R5

600 DPP02006R5250 400 DPP02504R5

600 DPP02506R5300 400 DPP03004R5

600 DPP03006R5400 400 DPP04004R5

600 DPP04006R5800 DPP04008R5



MultiFlex accessoriesCDV, Vertical divider

Description: The profile is identical to the enclosure frame and provides vertical separation of the enclosure when partial doors or cable way covers are fitted. Can be mounted in 200 mm steps.Material: 2 mm steel plate.Finish: Structure powder paint, RAL 7035.Pack. quantity: 1 set of profiles with fixing material.

H Part No.

1800 CDV1800R52000 CDV2000R52200 CDV2200R5

CDH, Horizontal divider

Description: Used when the enclosure requires separation by partial doors or panels. Can be mounted on the outside hole pattern of the open frames (MC versions).Material: 2 mm zinc plated steel.Pack. quantity: 2 profiles with mounting material.

W Part No.

400 CDH400600 CDH600800 CDH800

CDHK, Horizontal divider

Description: Used when the enclosure requires separation by partial doors or panels. Can be mounted in the hole pattern of closed frames (MK versions).Material: 2 mm zinc plated steel.Pack. quantity: 2 profiles with mounting material.

W Part No.

400 CDHK400600 CDHK600800 CDHK800

Chapter_03x_Power_x_Distribution_R5_2007_45297_3.fm Page 121 Wednesday, November 21, 2007 11:51 AM

122

Typ-Test-Durchführung1.

2.

3.

4.

5.

6.

7.

8.

Power and Distribution Visit our website at www.eldon.com

Eldon’s new modular low voltage system is based on the existing Multi-Flex mild steel fl oor standing enclosure, and therefore allows the user to design and build a complete solution from essentially a standard range of enclosures and accessories.

There is no limit to the size of project this system can handle (small, medium and large assemblies), and it can be used for a variety of different applications:

• Control aplications.

• Electrical distribution panels.

• Power systems.

To further enhance the fl exibility of the system, the designer or end user can specify any brand of electrical components to be used, as there are no restrictions to make, type or size.

The frame is a fully welded construction which helps guarantee the highest rigidity, and the possibility of coping with the very highest Icc (short-circuit current) requirements.

The Eldon Power System has been tested by ETL-Semko and ASTA according to IEC/EN 60439-1. The TTA tests were performed on fully equipped assemblies containing different IP ratings and various forms of internal segregation, and other system features such as a combination of different busbar systems.

One of the main advantages of the Eldon system is that you are able to manufacture a fully type-tested low-voltage switchgear and con-trolgear assembly (TTA) according to EN 64039-1. However, every system should meet the following conditions:

• The switching devices and components incorporated in the assembly shall comply with the relevant IEC standards, and should be suitable for the particular application with respect to the external design, rated voltages, rated currents, rated frequency, short-circuit protection, etc.

• The electrical connections inside the assembly must comply with EN 60439-1 7.8.

By following these standards and the relevant mounting instructions, the user only has to carry out the usual routine testing once the system is fully assembled, instead of any additional type testing (Wiring and electrical operation, dielectric properties and protective measures accord-ing to EN 60439-1 8).

ELDON MULTIFLEX LOW-VOLTAGE SWITCHGEAR SYSTEM

Type test carried out1. Temperature-rise limit

2. Dielectric properties

3. Short-circuit withstand strength

4. Effectiveness of the protective circuit

5. Clearances and creepage distances

6. Mechanical operation

7. Degree of protection

8. EMC test

Rated operational voltage: Up to 690 V Rated insulation voltage: Up to 690 V Rated impulse withstand voltage: Up to 4000 V Rated current: Up to 5000 A Rated short-time short-circuit current: 85 kA Rated peak short-circuit current: 187 kA Rated frequency: 40 – 60 Hz

Eldon Power System electrical features

Short-circuit test Thermal test

Busbar

pagina 113.indd 122 14/11/07 19:52:52

123Power and DistributionVisit our website at www.eldon.com

From IP20 with ventilation roof up to IP55.

ANY SOLUTION FOR ALL REQUIREMENTS

Modular components mounted on DIN-rail.Components mounted on a mounting plate.

Full height plain or transparent door.Partial panel.Partial door.(All with different locking combinations,to maximise security).

Vertical busbar behindcompartments up to 1600 A.

IF YOU REQUIRE ANY FURTHER INFORMATION, PLEASE DO NOT HESITATE TO CONTACTYOUR LOCAL ELDON SALES OFFICE, AND REQUEST THE NEW

“ELDON POWER SYSTEM” CATALOGUE.

Various types of compartments for:

Protection degree:

Internal segregation: External access:

Different types of busbars:

Shelf mounted Air circuit breakers.

Fixed connected units to “next to” or “behind” busbars.

Plug-in units.

From Form 1 to Form 4 according to EN60439-1, using standard ac-cessories.

Horizontal main busbar ontop or bottom up to 5000 A.

Horizontal main busbar behind compartments up to 3300 A.

Vertical busbar next tocompartments up to 1700 A.

Busbar

pagina 113.indd 123 14/11/07 19:53:51


MultiFlex

MCF

Flange Mount disconnect

IP55, NEMA 12, 13. IK10

Technical data

Material: Frame:1.5 mm painted steel. Doors: 2 mm painted steel. Rear, roof and side panels: 1.5 mm painted steel. Mounting plate: 3 mm galvanised steel. Bottom plates: 1 mm galvanised steel.Frame: Seam welded reversed open profiles with 25 mm hole pattern according to DIN 43660. Including integrated external hole pattern.Door: Surface mounted with four hinges. Including door frame with 25 mm hole pattern. Door cannot be reversed. Flange door: Surface mounted with hinges, locked from the inside, including universal cut-out.Rear panel: Fitted by M6 torx screws. Standard facilities for rear door mounting.Side panels: Supplied as an accessory.Roof panel: RemovableLock: Espagnolette 4-point locking system. Does not interfere with the enclosure inner space. Standard DIN-lock with 3 mm pin. Can be exchanged for standard inserts or Euro-cylinder, swing handle or digital locking system.

Bottom plates: Consists of three pieces.Mounting plate: Double folded and adjustable in depth by steps of 25 mm. Attached on the outside of the enclosure carton.Earthing: All panels are earthed through their fittings and are equipped with a separate earthing stud.Finish: Structured powder paint RAL 7035.Protection: Corresponds with IP 55 and NEMA 12, 13. IK10.Delivery: Frame with fitted doors, rear panel, roof panel, bottom plates, mounting plate and door frame. Delivery also includes earthing bolts. Delivered on a pallet with width identical with the enclosure to allow suiting without removal. All packing material recyclable.


125

MultiFlex


H W D Door Part No.

1800 800 400 600 MCF18084R5500 600 MCF18085R5

1000 500 800 MCF18105R52000 800 500 600 MCF20085R5

600 600 MCF20086R51000 500 800 MCF20105R5

Add FMD for complete system. For slave enclosures add FMA, FMB, FMS. Sides can be closed with side panels SPM.

Dimensions



MultiFlex

MKF

Flange mount disconnect compact

IP55/NEMA 12, 13. IK10

Technical data

Material: Body, rear and roof panels: 1.5 mm painted steel. Door: 2 mm painted steel. Mounting plate: 3 mm galvanised steel. Bottom plates: 1 mm galvanised steel.Body: Four times folded and seam-welded frame. Integrated double row hole pattern. Separate doors to be ordered for left hand door locking.Door: Surface mounted with four hinges. Including doorframe with 25mm hole pattern. Door cannot be reversed.Flange door: Surface mounted with hinges, locked from the inside, including universal cut-out.Rear panel: Fitted by M6 torx screws. Standard facilities for rear door mounting.Roof panel: RemovableBottom plates: Consists of three pieces

Lock: Espagnolette 4-point locking system. Does not interfere with the enclosure inner space. Standard DIN-lock with 3 mm pin. Can be exchanged for standard inserts or Euro-cylinder, swing handle or digital locking system.Mounting plate: Double folded and adjustable in depth by steps of 25 mm. Attached on the outside of the enclosure carton.Earthing: All panels are earthed through their fittings and are equipped with a separate earthing stud.Finish: structured powder paint RAL 7035Protection: Corresponds with IP 55 and NEMA 12, 13. IK10.Delivery: Frame with fitted doors, rear panel, roof panel, bottom plates, mounting plate and door frame. Delivery also includes earthing bolts. Delivered on a pallet with width identical with the enclosure to allow suiting without removal. All packing material recyclable.


127

MultiFlex


H W D Door Part No.

1800 800 500 600 MKF18085R51000 500 800 MKF18105R5

2000 800 500 600 MKF20085R51000 500 800 MKF20105R5

For a complete system add accessory FMD.

Dimensions


128



FMD, Main door interlock kit

Description: Locks or releases the main door after the power has been switched. Universal adapter permits all popular manufacturers variable depth actuators without modification.Material: Zinc plated steel.Pack. quantity: 1 piece with mounting material.

Part No.

FMD01

FMA, System actuator

Description: Used with suited multiple enclosure installations. Activates the locking of the slave doors when the master door is closed. One per multiple enclosure system.Material: Zinc plated steel.Pack. quantity: 1 piece with mounting material.

Part No.

FMA01



MultiFlex accessoriesFMS, Slave door interlock kit

Description: Mounted to the slave door of both single and double door enclosures. Main door is prevented from closing when slave doors are open. This safety feature can be activated separately even when the main door interlocking device is not installed. One set per slave door is needed.Material: Zinc plated steel.Pack. quantity: 1 set with mounting material.

Part No.

FMS01

FMB, Interlock bar

Description: For MCF/MCS enclosures. Interlock rods mechanically link all slave doors to the master door. Rod length corresponds to enclosure door width.Material: Zinc plated steel.Pack. quantity: 10 pieces with mounting material.

W Part No.

600 FMB600800 FMB800

1000 FMB10001200 FMB1200



MultiFlex

MCBA/MCBJ

Enclosure for ABB and Jean Mueller cassettes The enclosures are a ready to use solution for the mounting of low voltage fuse switch disconnector cassettes of ABB, SlimLine, SlimLine XR and Jean Mueller, Sasil cassettes of ABB (SlimLine) and Jean Mueller (Sasil).

IP30/NEMA 1

Technical data

Material: Frame: 1.5/1.75 mm painted steel. Door: 2.0 mm painted steel. Rear, roof and side panels: 1.35 mm painted steel. Bottom plates: 1.0 mm galvanised steel.Frame: Seam welded reversed open profiles with 25 mm hole pattern according to DIN 43660. Including integrated external hole pattern.Door: On right and side situated cable compartment, surface mounted with 4 hinges. Can be mounted either on the left or right hand side of the enclosure frame.Rear panel: Fitted by M6 torx screws. Standard facilities for rear door mounting.Side panels: Supplied as an accessory. Roof panel: Removable.Bottom plates: Consists of three pieces in the switch compartment and two pieces in the cable compartment. Only available on request.Lock: DIN 3 mm locking system. Does not interfere with the enclosure inner space. Standard DIN-lock with 3 mm pin can be exchanged for standard inserts or T-handle.

Earthing: All panels are earthed through their fittings and are equipped with a separate earthing stud.Finish: RAL 7035 structured powder paint.Protection: Corresponds with IP 30 and NEMA 1Delivery: Frame equipped with required hardware for the mounting of SlimLine, SlimLine XR or SASIL cassettes and its corresponding busbar system (3 or 4 pole), fitted door on cabling compartment, rear panel, roof panel and ventilated cable compartment panel. Delivery also includes earthing bolts. Delivered on a pallet with width identical with the enclosure to allow suiting without removal. All packing material recyclable. For information regarding the cassettes you can contact your local ABB or Jean Mueller distributor.


131

MultiFlex


H W D For Part No.

2000 1000 600 ABB/SlimLine (XR) MCBA20106R51200 600 ABB/SlimLine (XR) MCBA20126R51000 600 Jean Mueller/Sasil MCBJ20106R51200 600 Jean Mueller/Sasil MCBJ20126R5

Excluding cassettes.

Dimensions



MultiFlex

MCBA(V)

Enclosure for vertical ABB or Jean Mueller cassettes The enclosures are a ready to use solution for the mounting of low voltage fuse switch vertical disconnector cassettes of ABB, InLine and Jean Mueller, SL-fuse switch disconnectors

IP 30/NEMA 1

Technical data

Description: Frame: 1.5/1.75 mm steel plate. Doors: 2.0 mm steel plate. Rear, roof and side panels: 1.5 mm steel plate. Bottom plates: 1.0 mm galvanised steel.Frame: Seam welded reversed open profile with 25 mm hole pattern according to DIN 43660. Including integrated external hole pattern.Doors and panels: Right hand hinged, surface mounted. Can be mounted both left and right hand hinged without extra parts.Centre part: Suitable for either the ABB InLine or the JM SL-Cassettes.Rear panel: Fitted by M6 torx screws. Standard facilities for rear door mounting.Side panels: Supplied as an accessory.Roof panel: Removable.Bottom plates: Consists of three pieces. Available on request (CBP).

Lock: DIN 3 mm locking system. Does not interfere with the enclosure inner space. Standard DIN-lock with 3 mm pin can be exchanged for standard inserts or T-handle.Earthing: All panels are earthed through their fittings and are equipped with a separate earthing stud.Finish: Structured powder paint, RAL 7035Protection: Corresponds with IP 30 and NEMA 1Delivery: Frame equipped with required hardware for the mounting of InLine and SL cassettes (also IP20 protected versions) and its corresponding (busbar) fixing system, fitted doors (top/bottom), rear and roof panel. Delivery also includes earthing bolts. Delivered on a pallet with width identical with the enclosure to allow suiting without removal. All packing material recyclable. For information regarding the cassettes you can contact your local ABB or Jean Mueller distributor.


133

MultiFlex


H W D For Part No.

2000 800 600 ABB InLine MCBA20086VR51000 600 ABB/InLine MCBA20106VR5

800 600 JM/SL-fuse switch disconnector MCBJ20086VR51000 600 JM/SL-fuse switch disconnector MCBJ20106VR5

* available on request

Dimensions


134



MCAD, Hinged compartment cover

Description: Hinged font panel for covering of a breaker or fuse compartment. Fitted on one side with hinges and the other with torx screws. Can be mounted both left and right hand hinged.Material: 1.35 mm steel plateFinish: Structured powder paint, RAL 7035Pack. quantity: 1 hinged panel including mounting material.

H Part No.

600 MCAD600R5

MCAP, Ventilated front panel MCBA

Description: Front covers with ventilation louvres for maximum heat dissipation. Can only be used in combination with ABB SlimLine cassettes. For cover panels of Jean Mueller contact your local distributor. To cover unused spaces.Material: 1.35 mm steel plateFinish: RAL 7035 structured powder paint.Protection: Corresponds with IP 30 and NEMA 1Pack. quantity: 2 panels including mounting material.

H Part No.

50 MCAP050R5100 MCAP100R5200 MCAP200R5300 MCAP300R5400 MCAP400R5



MultiFlex accessoriesMCPA/J, Full height mounting profile

Description: When the full enclosure height is used, including busbar compartment, full height vertical mounting profiles need to be mounted in order to fill out the top of the enclosure as well.Material: 2.0 mm steel plateFinish: Zinc platedPack. quantity: 2 profiles including mounting material

* available on request only.

For Part No.

ABB/Slimline (XR) MCPA2000Jean Mueller/Sasil MCPJ2000


POWER AND DISTRIBUTION POWER DISTRIBUTION · 2009-08-21 · POWER DISTRIBUTION POWER AND...

Documents

Transcript of POWER AND DISTRIBUTION POWER DISTRIBUTION · 2009-08-21 · POWER DISTRIBUTION POWER AND...