Polaroid FLM1911
description
Transcript of Polaroid FLM1911
19” HD-Ready Wide-Screen LCD TV FLM-1911, FLM-1911M, FLA-1911B
SERVICE MANUAL 20060526
1
TABLE OF CONTENTS
1. Precautions and Safety Notices ………………………….……………2
2. Specifications……………………………………………………………...4
3. Front Panel Function Control Description ………………………….. 8
4. Adjusting Procedure ……………………………………………………12
5. Display Cell Defects Specifications………………………….……….13
6. Dissassembly Procedure……………………………………………….14
7. Spare Parts List by Model Number…………………………………...21
8. Exploded Diagram ……………………….. …………………………....22
9. System Block Diagrams .................................................................24
10. Schematic Diagrams ………………………...……………………25
11. PCB Layout Diagrams …………….………...………………………28
2
1. Precautions and Safety Notices
3
4
2. Specifications
Item Specifications Display pixels 1440 (H) x900 (V) pixels ( 1 pixel = 1 RGB cells ) Active Area 410.40mm (H) x 256.50mm (V) Pixel Pitch 0.285mm (H) x 0.285mm (V) Bezel opening 414.36mm(H)x260.45mm(V) Display Colors 16.2M Pixel Arrangement R+G+B vertical stripe Display Mode normally white Brightness 450cd/m2 typical Contrast Ratio 500:1 typical Brightness Uniformity 75% min. Viewing Angle CR 10 Color Chromaticity (CIE) White: X = 0.313 ± 10% , Y = 0.329 ± 10% Frame Rate 75Hz Response Time 6ms typical Surface Treatment Hard Coating(3H)
5
INPUT Source :
Connector type Inputs & Output Signals Video Format
Video Sound TV Main-TV NTSC F / IH Type None VIDEO Video+L/R Audio CVBS RCAx1(Yellew) RCA x 2 (Red ,
White) S-VIDEO S-Video + L/R Audio Y/C Mini Din 4 Pin RCA x 2 (Red ,
White) Component Auto Detect
YPbPr + L/R Audio 480i/480p, 576I/576P ,720p, 1080i
RCA x 3(Red, Blue ,Green
RCA x 2 (Red , White)
PC IN VGA + L/R Audio D-sub type for service port
AC IN Inverter AC Power IN AC 110~220V YC14
Note: A. VGA Connector IN. (This function also can provides to HDTV.)
VGA type connector pin assignment
1.Red Video 6.Red Ground 11.ISP-SEL-I
2.Green Video 7.Green Ground 12.SDA
3.Blue Video 8.Blue Ground 13.H-sync.
4.None 9.+5V 14.V-sync.
5.GND 10.Sync GND 15.SCL
B. RCA jacks are all female type.
C. Mini DIN CNC 4 Pins (SCN570S3NS00000) for S-video, the pin assignment is described as below:
1: Ground 2: Ground 3: Y 4: C
6
Analog HD15 PC Signal (RGB) Format R, G, B Analog Level/Impedance 0.7Vp-p / 75Ω DDC 1/2B Compliant with Revision 1.0 Sync H/V separate
3V TTL level / 1kΩ Frequency Fh = 31~80 kHz
Fv = 56~76 Hz Maximum Pixel Clock 135 Mhz Connector Mini D-Sub 15 pin (female) x 1
Video (Composite) CVBS Signal Format NTSC, 4.43NTSC, PAL Level / Impedance 1.0Vp-p / 75Ω
S-Video (Y/C) Signal Format Y, C Level / Impedance Y: 1.0Vp-p / 75Ω
C: ± 286 mV/ 75Ω
Analog HD15 Video Signal (YPbPr/YCbCr) Format Y, Pb, Pr or Y, Cb, Cr Level / Impedance Y: 1.0Vp-p / 75Ω
Pb/Cb, Pr/Cr: 0.7 ± 0.035Vp-p / 75Ω
RGB PC Timing
No. Resolution H-Freq.(KHz) V-Freq.(Hz) 1. 640 x 480 31.469 60 2 640 x 480 37.861 72 3 640 x 480 37.5 75 4 720x400 31.46 70.40 5 800x600 35.15 56.25 6 800 x600 37.879 60 7 800 x600 48.077 72 8 800 x600 46.87 75 9 1024x768 35.52 86.95 10 1024x768 48.363 60 11 1024x768 56.47 70 12 1024x768 60.023 75 13 1152x864 67.50 75.00 14 1280x960 60.00 60.00 15 1280x1024 63.98 60.02 16 1280x1024 79.97 75.02 17 1440x900 55.93 59.88 18 1440x900 70.63 74.98 19 1600x1200 75.00 60.00 20 1600x1200 81.25 65.00 21 1600x1200 87.50 70.00 22 1600x1200 93.75 75.00 23 1792x1344 83.64 60.00
7
Video & S-Video AV Timing
STANDARD RESOLUTION V FREQ Hz
H FREQ kHz
CLK MHz
NTSC 525 60 15.734 12.65
PAL 625 50 15.625 14.50
4.43NTSC 525 60 15.734 12.65
HDTV/Component AV Timing
No Resolution H-Freq.(KHz) V-Freq.(Hz) Pixel clock (MHz) Proposed
1 640 x 480 15.73 60 13.500 NTSC 525i 2 720 x 480 15.73 60.00 18.00 SDTV 480i 3 640 x 480 31.47 59.94 27.00 SDTV 480p 4 720x240 15.625 50.00 13.500M SDTV576i 5 720x756 31.25 50.00 27.00M SDTV576P 6 1280 x 720 44.96 59.94 74.25 HDTV 720P 7 1920 x 1080 33.75 60.00 74.25 HDTV 1080I
Power Source AC100 – 240 V, 60/50 Hz
Sound Output 3W X2, 4 Ohm.
8
3. Front Panel Function Control Description
Operation, Adjust and Programming
9
10
FLM-1911, FLM-1911M
11
FLA-1911B
12
The operation of each OSD controls is described as following table:
Main Menu Sub-Menu Adjustment Picture Mode Press / to change the Picture Mode to be Dynamic,
Mild, Vivid, custom Brightness Press / to adjust the Brightness from 0 to 100 Contrast Press / to adjust the Contrast from 0 to 100 Hue Press / to adjust the Hue from -50 to 50 Saturation Press / to adjust the Saturation from 0 to 100 Sharpness Press / to adjust the Sharpness from 0 to 100 Color Temperature Press / to select the Noise Temperature to be Warm,
Standard or Cool
VIDEO
Advanced Press / to select the Advanced to be on or off(Only for VGA)
Volume Press / to adjust the Volume from 0 to 100 Bass Press / to change the Bass from 0 to 100 Treble Press / to change the Treble from 0 to 100 Balance Press / to adjust the Balance from 0 to 100
Sound Mode Press / to change Sound Mode to be custom, movie, pop or rock
AUDIO
MTS Press / to adjust the MTS to be Mono, Stereo or SAP. Enter PIN Press 0-9 digital button to input passage
Change PIN After you configure your password, Press / to select the Change PIN to be New PIN, Re-Enter PIN
Clear All Press / to select the Clear All to be Yes or No
TV Rating After you configure your password, then you can set the TV Rating to be None, TV Youth, TV Youth7,TV-G,TVPG,TV-14,TV-MA
Movie Rating After you configure your password, then you can set the Moving Blocking ratings to be NA, G, PG, PG-13, R, NC-17,X.
CA Eng Rating
After you configure your password, then you can set the CA Eng Rating to be E,C, C8UP,G,PG,14UP,18UP
CA FR Raring
After you configure your password, then you can set the CA FR Rating to be E,C,8UP,13UP,16UP,18UP
PARENTAL
Parental Control
Parental Lock Press / to change Parental Lock to be On or Off
Channel System
Press / to select the channel system to be AIR, Cable-STD, Cable-HRC, Cable-IRC
Auto Search Press / to automatically search Tuner/Channel
Fine Tune Press / to adjust the Fine Tune from -50 to 50
Language Press / to select the Menu Language to be English, French, Spanish.
OSD Time Out Press / to select the Menu Timeout to be 5,10,15,20,25, 30 seconds
Sleep Time Press / to select the Sleep Timer to be 15, 30, 45, 60, 90, 120 minutes or Off
OSD Reset To return the factory value
SETUP
CC Mode Press / to select CC modeOFF,CC1 ,CC2,CC3or CC4,TT1,TT2,TT3,TT4.
4. Adjusting Procedure
13
FLM-19XX: Model Numbers FLM-1911, FLM-1911M, FLA-1911B In some cases, a panel may have defective cells that cannot be controlled. These defective cells can be categorized into two types; (1) Non-lighting or dark cell defect: defect in which the cell is always off (2) Non-extinguishing or bright cell defect: defect in which the cell is always on The display cell defect specifications define the allowed limits for display cell defects and are used as the criteria in determining whether a panel is replaced.
A ZONE: The center rectangle, with height of ½ of total height and width of ½ of total width A ZONE: Item Specification Bright cell 0 Dark cell 1 or less All bright and dark cells combined 1 or less B ZONE: Item Specification Bright cell 3 or less Dark cell 5 or less All bright and dark cells combined 5 or less
5. Display Cell Defect Specifications
14
Rear Cabinet Cover, Control Box and LCD
Step 1 1. Lay TV flat on workbench. Be careful to protect the front bezel and LCD screen from being scratched. Use protective cloth between workbench and TV front. 2. Remove single stand screw (PIC1) 3. Pivot stand and push stand off hinge pin on right side of TV (PIC2) 4. Proceed to next step
6. Dissassembly Procedure
Single Screw
15
Dissassembly Procedure Rear Cabinet Cover, Control Box and LCD
Step 2 1. Remove rear cabinet cover screws - 16 total (PIC1) 2. The top of the rear cabinet cover is still attached with snap locks. Lift the bottom part of the rear cabinet cover releasing it from the TV chassis. Once released stop. Using a plastic pry tool and carefully pry back the snap locks to release the rear cabinet cover top. (PIC2)
PIC1
PIC2
16
Dissassembly Procedure Rear Cabinet Cover, Control Box and LCD Step 3
1. Remove black tape (PIC1) 2. Disconnect the speaker wire and signal cable from the control box. (PIC1)
There are 4 connectors. Make note of their placement for assembly. DO NOT REMOVE ANYMORE TAPE AT THIS TIME THE SILVER TAPE IS EMI TAPE AND MUST STAY IN PLACE IF REMOVED THE EMI TAPE MUST BE REPLACED DURING ASSEMBLY
3. Proceed to next step.
Step 4 1. Lift up and remove control box/LCD panel subassembly from bezel and set aside . DO NOT SCRATCH LCD PANEL SURFACE, USE PROTECTIVE CLOTH 2. Proceed to next step
17
Dissassembly Procedure Rear Cabinet Cover, Control Box and LCD Step 5
1. Remove black tape (PIC1) 2. Gently remove the power board the backlight cables (PIC1) There are 4 connectors. Make note of their placement for assembly. 3. Proceed to next step
18
Dissassembly Procedure Rear Cabinet Cover, Control Box and LCD Step 6 1. Remove the 2 screws that secure the control box to the LCD panel (PIC1) 2. Lift control box and locate LVDS cable (PIC2) 3. Gently remove EMI and black tape to expose LVDS cable 4. Disconnect LVDS cable from LCD panel 5. Cut or remove EMI tape and separate control box from LCD panel (PIC3) 6. At this point replace control box or LCD panel 7. Proceed to next step
19
Dissassembly Procedure Rear Cabinet Cover, Control Box and LCD Step 7: **IMPORTANT** Make sure wires are placed in bezel wire channels during assembly (PIC1 & 2)
20
Subassembly Locations for Replacement 1. Speakers 2. Front Control Buttons/IR 3. Front/Side Earphone Board
21
7. Spare Parts List by Model Number
23
8. Exploded Diagrams
22
24
9. System Block Diagrams
25
Earphone Board
10. Schematic Diagrams
26
AV Board
27
Keypad Board
28
11. PCB Layout Diagrams
Tuner Board(Component Side Top)JP195HREVCPCB.pdf
29
Earphone Board(Component Side Top)JK195 earphone pcb.pdf
Earphone Board(Component Side Bottom)
Keypad Board (Component Side Top)
Keypad Board (Component Side Bottom)