PLUMBING FIXTURE SCHEDULE - Comma-Q€¦ · 26-7/8" (683 mm) x 18" (457 mm) x 14-1/8" (359 mm)...
Transcript of PLUMBING FIXTURE SCHEDULE - Comma-Q€¦ · 26-7/8" (683 mm) x 18" (457 mm) x 14-1/8" (359 mm)...
CW HW WASTE VENT
WC-1ADA TANK TYPE FLOOR MOUNT
WATER CLOSET KOHLER K-3609 CIMARRON SEAT - CHURCH 295SSC - INTEGRAL 18" 1/2" - 4" 2"
WC-2TANK TYPE FLOOR MOUNT
WATER CLOSET KOHLER K-3609 CIMARRON SEAT - CHURCH 295SSC - INTEGRAL 18" 1/2" - 4" 2"
UR-1 ADA WALL HUNG URINAL KOHLER K-4904-ET BARDON FLUSH VALVE - SLOAN 186-1.0 - INTEGRAL 17" 3/4" - 2" 1-1/2" 3
LAV-1 ADA WALL HUNG LAVATORY KOHLER K-2005 KINGSTON MOEN 8413F05LOOSE KEY
CHROME CHROME TRAP 34" 1/2" 1/2" 1-1/2" 1-1/2" 3
LAV-2 WALL HUNG LAVATORY KOHLER K-2005 KINGSTON MOEN 8413F05LOOSE KEY
CHROME CHROME TRAP 31" 1/2" 1/2" 1-1/2" 1-1/2" 3
MS-1 MOP SERVICE SINK FIAT MSB-2424830-AA FAUCET, 889-CC BRACKET, E-77-AA
GUARDS, 832AA HOSE BALL VALVES PVC FLOOR 1/2" 1/2" 3" 1-1/2"
SH-1 ADA SHOWER MOEN T8346, T8371HD 2.5 GPM FLOW CONTROL, SUPPLY STOPS INTEGRAL FLOOR DRAIN HEAD 6'-0" 1/2" 1/2" - - 2
FD-1 FLOOR DRAIN JR SMITH 2005-A-NB ROUND - - PVC FLOOR - - 2" 1-1/2" 1, 4
FS-1CAST IRON NSF 8" DEEP FLOOR
SINK JR SMITH 3410Y-13 3/4 GRATE - PVC FLOOR - - 3" 1-1/2" 1, 4
PLUMBING FIXTURE SCHEDULECONNECTIONS
REMARKS:
TAG MANUF. REMARKSROUGH-IN
HEIGHTFIXTURE
PROVIDE ADA SINKS AND LAVATORIES WITH INSULATED TRAPS, STOPS AND SUPPLIES. PROVIDE CHROME PLATED COMMERCIAL GRADE STOPS AND SUPPLIES.1. VERIFY EXACT LOCATION OF DRAIN WITH THE ARCHITECT/GENERAL PRIOR TO INSTALLATION.2. PROVIDE SHOWER VALVE WITH SINGLE LEVER PRESSURE BALANCED VALVE, INTEGRAL STOPS, TEMPERATURE LIMIT STOPS, HAND HELD SHOWER, 30" SLIDE BAR, 69" HOSE. 2.5 GPM FLOW.3. PROVIDE WITH FLOOR CARRIER4. PROVIDE TRAP PRIMER PORT. PROVIDE TRAP PRIMER VALVE WITH DISTRIBUTION UNIT. CONNECT UP TO FOUR DRAINS TO ONE TRAP PRIMER. CAP ANY UNUSED CONNECTIONS. PROVIDE BALL VALVE AND TOP PIPE CONNECTION FOR EACH VALVE.
GENERAL: INSTALL ADA FIXTURES PER LATEST ADA STANDARDS. INSTALL FLUSH VALVES WITH HANDLES TOWARD THE WIDE SIDE OF THE STALL.
MODEL TRAPSUPPLIESACCESSORIES
Features• Vitreous china.• Two-piece toilet.• Comfort Height® Elongated bowl.• AquaPiston® flushing system.• Includes left-hand polished chrome trip lever.• 1.28 gpf (4.8 lpf).• 2-1/8" (54 mm) fully glazed trapway.• 12" (305 mm) rough-in.• Less seat and supply.• 10-1/2" (267 mm) x 7-1/8" (181 mm) water area.• 28-3/4" (730 mm) x 17-5/8" (447 mm) x 30-3/4" (781 mm).• Floor mount / Floor outlet.
Recommended AccessoriesK-4650 Toilet Seat
CSA B651 OBC
K-7637 Angle Supply with Stop (single)
ComponentsProduct includes:
K-4309 Elongated Toilet BowlK-4421 Toilet TankAdditional included component/s: Tank cover, Trip lever, Boltcap accessory pack, and Tank accessory pack.
Codes/StandardsASME A112.19.2/CSA B45.1DOE - Energy Policy Act 1992EPA WaterSense®
ADAICC/ANSI A117.1CSA B651OBC
KOHLER® One-Year Limited WarrantySee website for detailed warranty information.
Available Color/FinishesColor tiles intended for reference only.
DescriptionCodeColor
White0
Biscuit96
Almond47
DuneNY
Ice™ Grey95
SandbarG9
Black Black™7
USA/Canada: 1-800-4KOHLER (1-800-456-4537)www.kohler.com5-23-2015 08:10
Cimarron®
Comfort Height® ToiletK-3609
For Back-to-Back Installations
NotesTechnical InformationInstall this product according to the installationguide.
All product dimensions are nominal.Two-pieceToilet type:
For back-to-back toilet installations: Use only a45° double wye fitting.
Elongated frontBowl shape:AquaPistonFlush type:
ADA, OBC, CSA B651 compliant when installedto the specific requirements of these regulations.
2-1/8" (54 mm)Trap passageway:Water Consumption
The Model Plumbing Codes require theinstallation of elongated open-front toilet seatson public bathrooms.
1.28 gpf (4.8 lpf)Full:10-1/2" x 7-7/8" (267 mm x 200 mm)Water surface size:6-3/8" (162 mm)Rim to water surface:12" (305 mm)Rough-in:5-1/2" (140 mm)Seat-mounting holes:
USA/Canada: 1-800-4KOHLER (1-800-456-4537)www.kohler.com5-23-2015 08:10
Cimarron®
Comfort Height® ToiletK-3609
SERIESSERIES
C O M M E R C I A L P L A S T I C S E A T S
Church Seats, Sheboygan Falls, WI 53085 Phone: 920-467-2664 800-233-7328 Fax: 920-467-8573www.ChurchSeats.com
MODEL 295C• ELONGATED SEAT, OPEN FRONT LESS COVER
• SOLID PLASTIC
• POSTUREPEDIC CONTOUR DESIGN
• CONCEALED 300 SERIES STAINLESS STEEL CHECK HINGES
18 1/2" 7 7/8" 19"
3 1/4"
14 1/4"
5 1/2"
295C Concealed check hinge stops seat 11° beyond vertical.295SSC Self-sustaining, concealed stainless steel check hinge holds seat in any raised positionup to 11° beyond vertical.
Seats shall be No. ____________ as manufactured by Church Seats.Seats shall be heavy weight and injection-molded of solid plastic. Seatsshall be open front less cover for elongated bowl and feature exclusivePosturepedic contour design and four large molded-in bumpers.Concealed check hinges to feature 300 Series stainless steel posts thatstop seat 11 degrees beyond vertical. Uses 300 Series stainless steelhardware. Color to be . (specify white or fixture manufacturer’scolor) Hinges shall be . (specify hinge type)
Ring thickness is 13/16"Ring thickness including the bumper is 1"Height of Seat is 2-1/4"
Features• Vitreous china.• Washout flushing action.• 3/4" top spud.• 14-1/8" (359 mm) extended rim.• 0.125 gpf (0.47 lpf) to 1.0 gpf (3.8 lpf).• WaterSense® compliant when used with WaterSense
flushometer.• Will replace K-4960-ET urinal.• 26-7/8" (683 mm) x 18" (457 mm) x 14-1/8" (359 mm)
Recommended AccessoriesK-10668 WaterSense® 0.125 gpf Exposed FlushometerK-10949 Tripoint™ DC 1/8 GPF Urinal FlushometerK-13520 WaterSense® 0.125 gpf Exposed FlushometerK-10675 WAVE DC 0.5 GPF Urinal FlushometerK-10958 Tripoint™ DC 0.5 GPF Urinal FlushometerK-13519 0.5 gpf Exposed FlushometerK-10676 WAVE DC 1.0 GPF Wshdwn FlushometerK-10960 1.0 gpf Exposed Flushometer
Codes/StandardsK-13518 1.0 gpf Exposed Flushometer
ComponentsAdditional included component/s: 3/4" inlet spud, 2" outlet spud,Strainer, and Hangers (2).
ASME A112.19.2/CSA B45.1EPA WaterSense®
ADAICC/ANSI A117.1
KOHLER® One-Year Limited WarrantySee website for detailed warranty information.
Available Color/FinishesColor tiles intended for reference only.
DescriptionCodeColor
White0
Biscuit96
Almond47
Black Black™7
USA/Canada: 1-800-4KOHLER (1-800-456-4537)www.kohler.com5-23-2015 04:47
Bardon™ 1/8th GPFHigh Efficiency Urinal (HEU)
K-4904-ET
21"
NotesTechnical InformationInstall this product according to the installationguide.
All product dimensions are nominal.3/4"Spud size:
ADA compliant when installed to the specificrequirements of these regulations.
USA/Canada: 1-800-4KOHLER (1-800-456-4537)www.kohler.com5-23-2015 04:47
Bardon™ 1/8th GPFHigh Efficiency Urinal (HEU)
K-4904-ET
DescriptionExposed Urinal Flushometer for ¾” top spud urinals.
Flush Cycle£Model 186 Water Saver (1.5 gpf/5.7 Lpf)£Model 186-1.0 Low Consumption (1.0 gpf/3.8 Lpf)
Variations£ DFB Dual Filtered Fixed Bypass Diaphragm
SpecificationsQuiet, Exposed, Diaphragm Type, Chrome Plated Urinal Flushometer with the followingfeatures:• High Chloramine Resistant PERMEX™ Synthetic Rubber Diaphragm with LinearFiltered Bypass and Vortex Cleansing Action™
• ADA Compliant Metal Oscillating Non-Hold-Open Handle with Triple Seal HandlePacking
• ¾” I.P.S. Screwdriver Bak-Chek™ Angle Stop• Vandal Resistant Stop Cap• Adjustable Tailpiece• Vacuum Breaker with Flush Connection• Spud Coupling and Spud Flange for ¾” Top Spud• Sweat Solder Adapter with Cover Tube and Cast Wall Flange• High Copper, Low Zinc Brass Castings for Dezincification Resistance• Non-Hold-Open Handle and No External Volume Adjustment to Ensure WaterConservation
• Low Consumption flush accuracy• Handle Packing, Stop Seat and Vacuum Breaker Molded from PERMEX™ RubberCompound for Chloramine Resistance
Valve Body, Cover, Tailpiece and Control Stop shall be in conformance with ASTM AlloyClassification for Semi-Red Brass. Valve shall be in compliance to the applicable sectionsof ASSE 1037.
AccessoriesSee Accessories Section of the Sloan catalog for details on these and other Flushometervariations.
SLOAN VALVE COMPANY • 10500 SEYMOUR AVE. • FRANKLIN PARK, IL 60131Ph: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380
www.sloanvalve.com
Sloan® ModelFlushometer
u
u
u
This space for Architect/Engineer approval
The information contained in this document is subject to change without notice.
Sloan 186 S.S. — Rev. 0d (06/10)Copyright © 2010 SLOAN VALVE COMPANY
u
186
u
Certified
Buy
American A
ct •
• C
ompliant
Buy
American A
ct •
• C
ompliant
Features• With hanger.• With overflow.• 4" (102 mm) centers.• 21-1/4" (540 mm) x 18-1/8" (460 mm).
Material• Vitreous china.
Installation• Wall-mount
Recommended AccessoriesK-8998 P-Trap
ComponentsAdditional included component/s: Hanger.
CSA B651 OBC
Codes/StandardsASME A112.19.2/CSA B45.1ADAICC/ANSI A117.1CSA B651OBC
KOHLER® One-Year Limited WarrantySee website for detailed warranty information.
Available Color/FinishesColor tiles intended for reference only.
DescriptionCodeColor
White0
Biscuit96
Almond47
Black Black™7
USA/Canada: 1-800-4KOHLER (1-800-456-4537)www.kohler.com5-23-2015 05:21
Kingston™
Wall-Mount Bathroom SinkK-2005
Concealed Arm Hole Locations
NotesTechnical InformationInstall this product according to the installationguide.
All product dimensions are nominal.SingleBowl configuration:
ADA, OBC, CSA B651 compliant when installedto the specific requirements of these regulations.
Wall-mountInstallation:Length: 16" (406 mm)Width: 10" (254 mm)Water depth: 3-1/8" (79 mm)
Bowl area (Only)
3Number of deck holes:1-1/4" (32 mm)Soap/Lotion hole:1-3/4" (44 mm)Drain hole:
USA/Canada: 1-800-4KOHLER (1-800-456-4537)www.kohler.com5-23-2015 05:21
Kingston™
Wall-Mount Bathroom SinkK-2005
NOTE: This faucet is designed to be in stalled thru 3 holes, 1" min. dia.
6"(153mm)
7"(128mm)
6-5/8"(168mm)
2-1/2"(64mm)
5"(127mm)
5-5/8"(143mm)
2"(51mm)
2"(51mm)
1-1/8" MAX.(29mm)
2-7/16"(62mm)
HOT COLD
55˚ 55˚
DESCRIPTION• Solid brass construction• Chrome, Brushed Chrome or Brushed Nickel finish• 1/2" IPS connections• Solid brass waterwaysOPERATION• Lever handle• Temperature controlled through 110˚ arc of handleFLOW• Standard aerator is limited to 2.2 gpm max. (8.3 L/min)CARTRIDGE• Ceramic disc cartridge *(with temperature limit stop)• Nonmetallic/nonferrous and ceramic materialSTANDARDS• Third party certified to WaterSense® (only applies to 1.5 gpm),
ASME A112.18.1/CSA B125.1, and all applicable requirementsreferenced therein including NSF 61/9
• Contains no more than 0.25% weighted average lead content • Complies with California Proposition 65 and with the Federal Safe
Drinking Water Act
• ADA for lever handles
WARRANTY• Warranted for 5 years against material or manufacturing defects
CRITICAL DIMENSIONS(DO NOT SCALE)
S p e c i f i c a t i o n s
MOEN SPECIFIER SERVICES 1-800-321-8809 Ext. 2158www.moen.comRev. 9/12
C O M M E R C I A L
MODEL FLOW (gpm) DRAIN FINISHWATERSENSECERTIFIED
8413 2.2 Without Chrome8413F15 1.5 Without Chrome x8413F05 0.5 Without Chrome8413F03 0.35 Without Chrome8414 2.2 Metal Chrome
8414BC 2.2 Metal Brushed Chrome8414BN 2.2 Metal Brushed Nickel
Single Handle Lavatory Faucet
See table above
FEATURES
NOTES
CR/PL© 04/03 Printed in U.S.A.
OPTIONS
FIAT PRODUCTSA CRANE PLUMBING COMP ANY
¤
MOLDED-STONE®
MOP SERVICE BASIN
MSB 2424MSB 3624
Molded-Stone® Mop Service Basin
• MSB 2424
The MSB 2424 shall have overall outside dimensions of 24” x 24” x 10”. The molding shall be done in matched metal dies under heat and pressure resulting in a one-piece homogeneous product. The unit shall have 10”high walls with not less than 1” wide.
The stainless steel drain body is designed to provide for a caulk connection or QDC-3 joint to a 3” drain pipe. A combination dome strainer and lint basket made from stainless steel shall be included with factory installed stainless steel drain body for caulked joint to accept a 3” pipe.
• MSB 3624
The MSB 3624 shall have overall outside dimensions of 36” x 24” x 10”. The molding shall be done in matched metal dies under heat and pressure resulting in a one-piece homogeneous product. The unit shall have 10”high walls with not less than 1” wide shoulders and an integrally molded shelf 10 9⁄16” wide whereindicated.
The stainless steel drain body is designed to provide for a caulk connection or QDC-3 joint to a 3” drain pipe. A combination dome strainer and lint basket made from stainless steel shall be included with factory installed stainless steel drain body for caulked joint to accept a 3” pipe.
• Service Faucet (830-AA): Chrome plated with vacuum breaker, integral stops, adjustable wall brace, pail hook and 3⁄4” hose thread on spout.
• Hose and Hose Bracket (832-AA)
• Mop Hanger (889-CC)
• Alternate Strainer (1453-BB) - For residential use (EFS-3624 and EFS-2424)
• 3” Quick Drain Connector (QDC-3XH): Neoprene connecting gasket suitable for attaching extra heavy cast iron soil pipe and Schedule 40 steel pipe to the drain body. Neoprene connecting gasket (QDC-3SN) suitable for attaching hubless cast iron pipe (no hub, nominal O.D. of 3.31”) and service weight cast iron soil pipe (nominal O.D. of 3.38”) to the drain body.
• Silicone Sealant (833-AA)
• Vinyl Bumperguard (E-77-AA)
• Stainless Steel Bumperguard (E-88-AA)
• Stainles Steel Wall Guard (MSG2424, MSG2828, MG3232, MSG3636, and MSG3624)
IMPORTANT: Roughing-in dimensions may vary 1/2" and are subject to change or cancellation without prior notice.CR/PL© 04/03 Printed in U.S.A.
FIAT PRODUCTSA CRANE PLUMBING COMP ANY
¤
Molded-Stone® Mop Service Basin
MSB 2424MSB 3624
MOLDED-STONE®
MOP SERVICE BASIN
MOEN SPECIFIER SER VIC ES 1-800-321-8809 Ext. 2158www.moen.com
Specifications
CRITICAL DIMENSIONS(DO NOT SCALE)
DESCRIPTION• Metal and brass construction with Chrome plated finish, also in
Classic Brushed Nickel (CBN) finish • Pressure balancing cycle valve• Contains: hand-held shower, with non-positive pause, 30" slide bar, drop ell,
vacuum breaker, 69" metal hose and mounting hardware • Slide bar is NOT DESIGNED TO BE A GRAB BAR• Supplied with vandal resistant screws • Quick cleaning rubber nozzles OPERATION• Temperature valve has ADA compliant lever style handle • Handle operates counterclockwise through a 270° arc
with off at 6 o'clock, and maximum hot at the 9 o'clock position. Shut off in clockwise direction
• Adjustable temperature limit stop • Pressure balancing mechanism maintains selected discharge temperature to ± 3.6° • Single function spray pattern • Easy to operate pause button (reduces the flow of water to a trickle) FLOW� T8346 (2.5gpm/9.5 lpm) - Chrome finish� T8346CBN (2.5gpm/9.5 lpm) - CBN finish� T8346EP15 (1.5gpm/5.7 lpm) - Chrome finish; WaterSense® Certified� T8346EP15CBN (1.5gpm/5.7 lpm) - CBN finish; WaterSense® CertifiedCARTRIDGE• Pair with a brass Posi-Temp rough-in valve:• 8370HD*: 1/2" CC connection without integral stops• 8371HD*: 1/2" CC connection with integral stops• 8372HD*: 1/2" IPS connection with integral stops• 8373HD*: 1/2" PEX connection with integral stops• 8374HD*: 1/2" CPVC connection with integral stops• 8375HD*: 1/2" UPONOR connection with integral stops
*Includes the 1222HD Brass Posi-Temp Cartridge• Accommodates back to back installations STANDARDS• Third party certified to WaterSense® (only applies to 1.5 gpm)
ASME A112.18.1/CSA B125.1 and all applicable requirements referenced therein
• ADA for lever handle
WARRANTY• Warranted for 5 years against material or manufacturing defects
Single-Handle Posi-TempHandheld Shower System
Model: T8346, T8346CBN
Rev. 11/12
FLOOR LINE
6'-6"(1981mm)NOMINAL
3/16" (21mm) - 2" (51mm)with optional adapter
FINISHEDWALL LINE
ESCUTCHEON
HANDLE
4-1/2" (114mm) PLASTER GUARD
OPENING
7" (178mm)ESC. DIAM.
DIRECTION OF HANDLE ROTATION
LC
3" (76mm)MIN. WALL
CAVITY
DROP ELL
1/2-14 NPT
2" Diameter
1/2-14NPSL THREAD
45" (1143)48" (1219mm)
NOMINAL
2-1/2" MAX. (63mm)
1/2" MIN. CC (13mm) 5/8" MIN. IPS (16mm)
H C
VacuumBreaker
28-1/2"NOMIMAL(723mm)
FLOOR LINE
6'-6" (1981mm)NOMINAL
DROP ELL
TUB RIM
FINISHEDWALL LINE
1/2-14 NPT
1/2-14NPSL
THREAD
2" Dia.
3-5/16" (85mm) SPRAY HEAD
DIAMETER
8-1/8" (206mm)SPRAY WAND
HEIGHT
*Refer to (ADAAG) guidelines or local codes for proper ADA installation.
C O M M E R C I A L
FIG
UR
EN
UM
BE
RD
RA
WN
BY
:
DIM
EN
SIO
NS
AR
E S
UB
JEC
T T
O M
AN
UFA
CT
UR
ER
S T
OLE
RA
NC
E A
ND
CH
AN
GE
WIT
HO
UT
NO
TIC
E
WE
CA
N A
SS
UM
E N
O R
ES
PO
NS
IBIL
ITY
FO
R U
SE
OF
SU
PE
RS
ED
ED
OR
VO
ID D
ATA
CH
EC
KE
D B
Y:
AP
PR
OV
ED
BY
:D
ATE
:S
CA
LE:
DR
AW
ING
NU
MB
ER
LOCATION
FIGURE NUMBERVOLUMECUBIC FEET
WEIGHTPOUNDS
CKD. BYBYDATEREV. DESCRIPTION
SIZ
E AN
ON
E
FLOOR OR SHOWER DRAINSWITH ADJUSTABLE STRAINER HEADS
FUNCTION: General service floor drain for use in showers, toilets, kitchens and other finished areas where foot traffic is expected. The round top strainer head is used for all types of poured finished floors. The square top is particularly adaptable to floors that are finished in material of square or straight line pattern. Reversible flashing collar permits adjustment of the strainer to meet finished floor level.
2005
2005
PJ
TD
TD
5-17
-85
S20
05Q
SEE PM0457 FOR OPTIONAL STRAINER HEADS.
CLM 10/24/06 N 12/18/08 Addition to Variations JJ BW P 11-20-09 Revised Variations RN BW Q 11-18-11 Rev. Dwg., Var. TBW CR
NO-HUB to SPEEDI-SET RN
NOTE: Dimensions shown in parentheses are in millimeters.
Meets ASME Standard A112.6.3-2001 02(50), 03(75) or 04"(100) sizes only.
StrainerSize
BDIA or SQ
05 (125)06 (150)07 (180)08 (205)•09 (230)•10 (255)
*CollarIn HighPosition
X MIN MAX 1 1/4(32) 2 1/4(57) 1 1/4(32) 2 1/4(57) 1 1/4(32) 2 1/4(57) 1 1/2(38) 2 1/2(64) 1 1/2(38) 2 3/8(60) 1 1/2(38) 2 3/8(60)
*CollarIn Low
PositionXX
MIN MAX 3/4(19) 1 5/8(41) 3/4(19) 1 5/8(41) 7/8(22) 1 7/8(48) 1(25) 1 7/8(48) 1(25) 1 7/8(48) 1(25) 1 7/8(48)
Free AreaSQ IN
(SQ CM)
ROUND SQUARE 7(45) 6.5(42) 9(58) 12.5(81) 14(90) 11(71) 17(110) 14(90) 18(116) 16(103) 23(48) 16(103)
OutletSize
02(50)03(75)04(100)
Nickel BronzeStrainer Head
05(125) DIA or SQ06(150) DIA or SQ08(205) DIA or SQ
Fig. 2005L……(A) ROUND TOPFig. 2005L……(B) SQUARE TOP
Fig. 2005Y……(A) ROUND TOPFig. 2005Y.……(B) SQUARE TOP
A (Pipe Size) = 02(50), 03(75), 04(100), 05(125) or 06(150)
SPEEDI-SET OUTLET
••
NO-HUB OUTLET
MAX
HighPosition
MAX
LowPosition
MAX
HighPositionLow
Position
MAX
Trap PrimerConnection(When Specified)
XX-MIN X-MIN
4(100) 1 1/4 (32)
Trap PrimerConnection(When Specified)
XX-MIN X-MIN
4(100)
SeepageOpenings
SeepageOpenings
**6 3/4 (170)
A
9 (230) DIA
B DIA or SQ
9 (230) DIA
B DIA or SQ
**6 3/4 (170)
A
1 1/4 (32)
▲▲▲
▲
▼ 2 5/8"(67)
▼ This dimension to internal stop of speedi-set gasket.• Add 3/8"(10) to all min/max dimensions for round strainers.* Collar is reversible to obtain extreme high and low strainer positions.•• Not available for 5"(125) size strainer.** MIN 6 3/4"(170) hole required for core drilled application.
REGULARLY FURNISHED: Duco Cast Iron Body with Flashing Collar and Adjustable Strainer Head as Indicated by Suffix Letter Selected.
VARIATIONS:Flapper Type Backwater Valve -VHinged Grate -HL Speedi-Set Service Weight 2(50), 3(75) & 4"(100) onlyLXH Speedi-Set Extra Heavy 2(50), 3(75) & 4"(100) onlySediment Bucket -BTrap Primer Connection -P050 1/2" (13) & -P075 3/4" (19)Vandal Proof Screws -UWide Flanged Strainer (Specify Fig. DX2005)T Threaded OutletHeelproof Grate -HP -AHP (Round) or -BHP (Square)
OPTIONAL MATERIALS:Bronze Body -BBChrome Plated Strainer -CPGalvanized Cast Iron Body -GNickel Bronze Strainer -NBPolished Bronze Strainer -PBStainless Steel (Specify Fig. 9700-A)
JAY R.SMITH MFG. CO.®
MEMBER OF ACORN’S FAMILY OF COMPANIESPOST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 www.jrsmith.com
CUSTOMERDRIVEN
SMITH®
MEMBER OF:
®
ASPE®
SANITARY
EN G IN E E RINGPrevention Rather Than Cure
B
H
FIGURE NUMBER
LOCATION
A
OPTIONAL STRAINER HEADS ROUND STRAINER
MATERIALS:Chrome Plated -CPPolished Bronze -PB
VARIATIONS:*Hinged Grate (Specify Suffix -AH)Sediment Bucket -BVandal Proof Screws -U
SUFFIX -A
B DIA 05 (125) 06 (150) 07 (180) 08 (205) 09 (230) 10 (255) H 2 (51) 2 (51) 2 1/4 (57) 2 1/2 (64) 2 1/2 (64) 2 3/4 (70) MIN 1 1/4 (32) 1 1/4 (32) 1 1/4 (32) 1 1/2 (38) 1 1/2 (38) 1 1/2 (38) MAX 2 1/4 (57) 2 1/4 (57) 2 1/4 (57) 2 1/2 (64) 2 1/2 (64) 2 3/4 (70)X
Specify Type, Size & Finish eg: A05NB*Not available for 05" (125) size
SUFFIX -B
MATERIALS:Chrome Plated -CP Flapper Type Backwater Valve
(Specify Suffix -BV) 05 (125), 06 (150), 07 (180) or 08" (205) sizes only*Hinged Grate (Specify Suffix -BH)Sediment Bucket -BVandal Proof Screws -U
Polished Bronze -PB
VARIATIONS:
SQUARE STRAINER
B DIA 05 (125) 06 (150) 07 (180) 08 (205) 09 (230) 10 (255) H 2 (51) 2 (51) 2 1/4 (57) 2 1/2 (64) 2 1/4 (57) 2 1/4 (57) MIN 1 1/4 (32) 1 1/4 (32) 1 1/4 (32) 1 1/2 (38) 1 1/2 (38) 1 1/2 (38) MAX 2 1/4 (57) 2 1/4 (57) 2 1/4 (57) 2 1/2 (64) 2 1/4 (57) 2 3/8 (60)X
Specify Type, Size & Finish eg: B05NB*Not available for 05" (125) size
B
H
Specify Type, Size & Finisheg: BSNB
SUFFIX -BS
MATERIALS:Chrome Plated -CPPolished Bronze -PB
VARIATIONS:Gasketed Water Tight Cover -GCSecured Cover -SCSecondary Strainer Grate-SG
STRAINER HEAD w/SQUARE HINGED COVER
6
3 1/8
SUFFIX -C Specify Type, Size & Finish eg: C06NB
REINFORCED ROUND STRAINER
MATERIALS:Chrome Plated -CPPolished Bronze -PB
VARIATIONS:Flapper Type Backwater Valve (Specify Suffix -CV)Sediment Bucket -BVandal Proof Screws -U
B DIA 05 (125) 06 (150) 08 (205) 10 (255) H 2 (51) 2 (51) 2 1/2 (64) 2 3/4 (70) MIN 1 1/4 (32) 1 1/4 (32) 1 1/2 (38) 1 7/8 (48) MAX 2 1/4 (57) 2 1/4 (57) 2 1/2 (64) 2 3/4 (70)
FUNCTION: Used in finished floors where light wheeled loads are anticipated.
B
H
TILE FLANGE
Specify Type, Size & Finish eg: F06NB
FUNCTION: Provides integral flange set 5/32" (4) below rim to receive floor covering. Flange may have option of tapped holes for securing pan and gasket.
MATERIALS:Chrome Plated -CPPolished Bronze -PB
VARIATIONS:
XMIN MAX
1 1/4 (32) 2 1/8 (54)
7 1/2
5/326
2
SUFFIX -F37-F38 Specify Type, Size & Finish eg: F37NB F38CP
FUNCTION: Used in a non-traffic area when a funnel type strainer head is required and space does not allow use of the 3500 series funnel. The extended rim allows use as an anti-flood and anti-splash drip pan.
MATERIALS:VARIATIONS:Flapper Type Backwater Valve (Specify Suffix -F37V or F38V)
Cast Iron -CIChrome Plated -CPGalvanized Cast Iron -GPolished Bronze -PB
ADJUSTABLE STRAINER HEAD
B
HSUFFIX -F37 -F38 B DIA 07 (180) 09 (230) H 3 1/4 (83) 3 1/2 (89) MIN 2 5/8 (67) 2 3/4 (70) MAX 3 1/2 (89) 3 1/2 (89)X
2010 SERIES OPTIONALSTRAINER HEADS
1 0f 2
2010
SE
RIE
S O
PT
ION
AL
ST
RA
INE
R H
EA
DS
FIG
UR
E
NU
MB
ER
DR
AW
N B
Y:
CH
EC
KE
D B
Y:
AP
PR
OV
ED
BY
:D
ATE
:S
CA
LED
RA
WIN
G N
UM
BE
R
DIM
EN
SIO
NS
AR
E S
UB
JEC
T T
O M
AN
UFA
CT
UR
ER
S T
OLE
RA
NC
E A
ND
CH
AN
GE
WIT
HO
UT
NO
TIC
E
A
SS
UM
E N
O R
ES
PO
NS
IBIL
IT O
R U
SE
OF
SU
PE
RS
ED
ED
OR
VO
ID D
ATA
SIZ
E
SUFFIX -AV
Specify Type, Size & Finish eg: AV05NB*Not available for 05" (125) size
FLAPPER TYPE BACKWATER VALVE
MATERIALS:Chrome Plated -CPPolished Bronze -PB
FUNCTION: Provides backwater pro-tection at point where protection is needed.
VARIATIONS
B
H
B DIA 05 (125) 06 (150) 07 (180) 08 (205) H 2 (51) 2 (51) 2 1/4 (57) 2 1/2 (64) MIN 1 1/4 (32) 1 1/4 (32) 1 1/4 (32) 1 1/2 (38) MAX 2 1/4 (57) 2 1/4 (57) 2 1/4 (57) 2 1/2 (64)
X
SUFFIX -D-E Specify Type, Size & Finish eg:
REINFORCED TRACTOR STRAINER
MATERIALS:Cast Iron -CIChrome Plated -CPPolished Bronze -PB
FUNCTION: Used in finished floors where medium weight wheeled loads are anticipated and loose set non-tilt tractor grate is desired.
VARIATIONS:
B
H
SUFFIX B H X DIA MIN MAX -D 07 (180) 3 1/4 (83) 2 5/8 (67) 3 1/2 (89) -E 09 (230) 3 1/2 (89) 2 3/4 (70) 3 1/2 (89)
REV. DATE DESCRIPTION BY CKD. BY
PJ
TD
TD
5-17
-85
NO
NE
PM
0457
SH
1 o
f 2G
6 (150)
3 1/8 (79)
6 (150)7 1/2 (190)
5/32 (4)
2 (51)
NOTE: Dimensions shown in parenthesis are in millimeters.
SUFFIX -F
BSE 11-4-97 Added Nickel Bronze EMBBS
CL
F 6-11-99 Revised Tables CMDEG 10-4-01 Revised Suffix-BS RN
8-24-99 Revised TBW
Nickel Bronze -NB
Nickel Bronze -NB
Nickel Bronze -NB
Nickel Bronze -NB
Nickel Bronze -NBNickel Bronze -NB
Nickel Bronze -NB
Nickel Bronze -NB
Hinged Grate (Specify Suffix -AH)Vandal Proof Screws -U
*
Flapper Type Backwater Valve (Specify Suffix -DV or -EV)Sediment Bucket -BVandal Proof Screws -U
D09PBE09PB
Flapper Type Backwater Valve (Specify Suffix -FV)Holes in Flange -SHSediment Bucket -BVandal Proof Screws -U
JAY R.SMITH MFG. CO.®
MEMBER OF ACORN’S FAMILY OF COMPANIESPOST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 www.jrsmith.com
CUSTOMERDRIVEN
SMITH®
MEMBER OF:
®
ASPE®
SANITARY
EN G IN E E RINGPrevention Rather Than Cure
FIGURE NUMBER
LOCATIONA
OPTIONAL STRAINER HEADS
Specify Type, Size & Finisheg: H05CP
B DIA 05 (125) 06 (150) 07 (180) 08 (205) H 2 (51) 2 (51) 2 1/4 (57) 2 1/2 (64) MIN 1 1/4 (32) 1 1/4 (32) 1 1/4 (32) 1 1/2 (38) MAX 2 1/4 (57) 2 1/4 (57) 2 1/4 (57) 2 1/2 (64)
X
SUFFIX -H
SOLID HINGED COVER
FUNCTION: Used in areas where intermittentdrain use is required. Solid cover preventsintrusion of chips, saw-dust, etc., which areswept up before cover is opened for washdown.The secondary strainer prevents debris fromentering the waste line.
H
B
SUFFIX -GSpecify Type, Size & Finish
eg: G08PB
B DIA 05 (125) 06 (150) 08 (205) H 2 (51) 2 (51) 2 1/2 (64) MIN 1 1/4 (32) 1 1/4 (32) 1 1/2 (38)MAX 2 1/4 (57) 2 1/4 (57) 2 1/2 (64)
LOW DOME STRAINER
MATERIALS:Chrome Plated -CPPolished Bronze -PB
FUNCTION: Used in gutters and recessed areas where excessive debris build-up is expected. Dome insures drainage even when partly covered.
H
B
Specify Type, Size & Finisheg: J06NBSUFFIX -J
FUNCTION: Solid gas tight, vandal proof, threaded cover for areas where intermittent drain use is required.
MATERIALS:Chrome Plated -CPPolished Bronze -PB
SPANNER WRENCH COVER
XMIN MAX
2 (51) 3 (76)
Specify Type, Size & Finisheg: K07CP
B SQ 05 (125) 06 (150) 07 (180) 08 (205) H 2 (51) 2 (51) 2 1/4 (57) 2 1/2 (64) MIN 1 1/4 (32) 1 1/4 (32) 1 1/4 (32) 1 1/2 (38) MAX 2 1/4 (57) 2 1/4 (57) 2 1/4 (57) 2 1/2 (64)X
SUFFIX -K
FUNCTION: Used in finished floors where some light wheeled traffic is anticipated.
MATERIALS:Chrome Plated -CPPolished Bronze -PB
REINFORCED SQUARE STRAINER
H
B
ANGLE STRAINER
Specify Type, Size & Finisheg: VPB, WNB
SUFFIX -V -W
MATERIALS:Cast Iron -CIChrome Plated -CPPolished Bronze -PB
FUNCTION: Shower room drain set at wall and floor junction. Vertical grate openings prevent drain stoppage should flat surface become covered.
VARIATIONS:Vandal Proof Screws -U
D
C
2 1/2
B
SUFFIX B C D X -V 3 1/2 (89) 3 1/2 (89) 4 1/2 (115) 1 5/8 (41) 2 5/8(67) -W 6 3/4 (170) 6 3/4 (170) 6 1/2 (165) 1 5/8 (41) 2 5/8(67)
Specify Type, Size & Finisheg: YCP, ZCPSUFFIX -Y-Z
FUNCTION: Used as overflow drain in decorative pools, fish ponds or similar areas. Dome prevents floating objects from entering drain line.
VARIATIONS:Less Dome -LDStandpipe Height other than 6" (150) (Specify Height)
MATERIALS:Chrome Plated -CPNickel Bronze -NBPolished Bronze -PB
OVERFLOW WITH STANDPIPE
A
4 1/2
2
6
SUFFIX A X SIZE MIN MAX -Y 2 (51) 3/4 (19) 2 1/8 (54)
-Z 3 (76) 3/4 (19) 2 1/8 (54)
2010 SERIES OPTIONALSTRAINER HEADS
2 of 2
2010
SE
RIE
S O
PT
ION
AL
ST
RA
INE
R H
EA
DS
FIG
UR
E
NU
MB
ER
DR
AW
N B
Y:
CH
EC
KE
D B
Y:
AP
PR
OV
ED
BY
:D
ATE
:S
CA
LED
RA
WIN
G N
UM
BE
R
DIM
EN
SIO
NS
AR
E S
UB
JEC
T T
O M
AN
UFA
CT
UR
ER
S T
OLE
RA
NC
E A
ND
CH
AN
GE
WIT
HO
UT
NO
TIC
E
A
SS
UM
E N
O R
ES
PO
NS
IBIL
IT O
R U
SE
OF
SU
PE
RS
ED
ED
OR
VO
ID D
ATA
SIZ
E
Specify Type,Size & Finisheg: LNB
RECTANGULAR STRAINER
MATERIALS:Chrome Plated -CPPolished Bronze -PB
VARIATIONS:Sediment Bucket -BVandal Proof Screws -U
FUNCTION: Used in finished floors where light wheeled loads and or heavy foot traffic are anticipated.
SUFFIX L M N P R T B x B' 4 1/2(115)x8(205) 4(100)x12(305) 5(125)x9(230) 5(125)x13(330)6(150)x10(255) 5(125)x17(430) H 2 1/4 (57) 2 1/2 (64) 2 1/4 (57) 3 (76) 2 1/4 (57) 3 (76) MIN 1 3/8 (35) 1 7/8 (48) 1 3/8 (35) 2 1/8 (54) 1 3/8 (35) 2 1/4 (57) MAX 2 3/8 (60) 2 3/4 (70) 2 3/8 (60) 3 (76) 2 3/8 (60) 3 1/8 (79)X
H
B x B'
SUFFIX -L-M-N-P-R-T
FUNCTION: Used in finished floors where light wheeled loads and or heavy foot traffic are anticipated.
MATERIALS:Polished Bronze -PBRough Bronze -RB
HEAVY DUTY ADJUSTABLE
2 3/16
6
SUFFIX -69SUFFIX -X
EXTENSION ADAPTOR
FUNCTION: Used when a strainer head must be raised to accommodate deeper floor fill.
REGULARLYFURNISHED:Duco Cast Iron -CI
MATERIALS:Cast Bronze -CBGalvanized Cast Iron -G
NOTE: Extension can be stacked for increased maximum adjustment.
MIN 2 1/2MAX 3 3/4
3 3/4 - 12
REV. DATE
E 11-4-97 Added Nickel Bronze EMBF 1-22-99 T Strainer was S Strainer TBW
DESCRIPTION BY CKD. BY
PJ
TD
TD
5-17
-85
NO
NE
PM
0457
SH
2 o
f 2H
8 1/4 x 3 1/4 Oval(210) x (83)
4 1/2(115)
5 x 2 1/2(125) x (64)
4 (100) DIA
4 1/4 (110)
2 1/2(64)
5 x 2 1/2(125) x (64)
1 (25)
Fig. 3580
6 DIA (150)
4 1/4 (110)
2 1/2(64)
Fig. 3581 Fig. 3590Fig. 3591
MIN MAX
2 1/2 (64)
3 3/4 - 12 (95)
MIN 2 1/2 (64)MAX 3 3/4 (95)
4 1/2(115)
6 (150)
2 (51)
6 (150)
2 3/16 (56)
6 x 2 1/2 Oval(150) x (64)
NOTE: Dimensions shown in parenthesis are in millimeters.
eg: A06NB-69
BSBS
G 6-11-99 Revised Tables CMDH 8-24-99 Revised TBW
BS
BS
D 10-28-96 Chg'd Func of Suffix -V -W
Nickel Bronze -NB
Nickel Bronze -NBNickel Bronze -NB
Nickel Bronze -NB
Nickel Bronze -NB
Nickel Bronze -NB
3(76)
6(150)
VARIATIONS:Flapper Type Backwater Valve (Specify Suffix -GV)Sediment Bucket -BVandal Proof Screws -U
VARIATIONS:Flapper Type Back- water Valve(Specify Suffix -KV)Sediment Bucket -BVandal Proof Screws -U
VARIATIONS:Flapper Type Back- water Valve(Specify Suffix -69V)Sediment Bucket -BVandal Proof Screws -U
VARIATIONS:Flapper Type Backwater Valve (Specify Suffix -GV)Vandal Proof Screws -U
VARIATIONS:Flapper Type Back- water Valve (Specify Suffix -JV)Holes in Flange -SHSediment Bucket -BVandal Proof Screws -U
MATERIALS:Cast Iron -CIChrome Plated -CPPolished Bronze -PBNickel Bronze -NB
JAY R.SMITH MFG. CO.®
MEMBER OF ACORN’S FAMILY OF COMPANIESPOST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 www.jrsmith.com
CUSTOMERDRIVEN
SMITH®
MEMBER OF:
®
ASPE®
SANITARY
EN G IN E E RINGPrevention Rather Than Cure
REV. DATE DESCRIPTION BY CKD. BY
WEIGHTPOUNDS
VOLUMECUBIC FEET
FIGURE NUMBER
LOCATIONFI
GU
RE
NU
MBE
R
DIM
ENSI
ON
S AR
E SU
BJEC
T TO
MAN
UFA
CTU
RER
S TO
LER
ANC
E AN
D C
HAN
GE
WIT
HO
UT
NO
TIC
EW
E C
AN A
SSU
ME
NO
RES
PON
SIBI
LITY
FO
R U
SE O
F SU
PER
SED
ED O
R V
OID
DAT
A
DR
AWN
BY:
CH
ECKE
D B
Y:AP
PRO
VED
BY:
DAT
E:SC
ALE:
SIZE A
DR
AWIN
G N
UM
BER
10 (255) SQ8 (205) SQ
2 (51)
6 (150)
3 (76)
A
10 (255) SQ8 (205) SQ
2 (51)
6 (150)
3 (76)
A
OPTIONAL TOP GRATES AND COVERS FOR INDIRECT WASTE APPLICATIONSSUFFIXNUMBER DESCRIPTION
-10 . . . . . . . . . . Less A.R.C. Grate-12 . . . . . . . . . . With A.R.C. 1/2 Grate-13 . . . . . . . . . . With A.R.C. 3/4 Grate-14 . . . . . . . . . . With A.R.C. Grate with 2 1/2" (64) DIA Center Hole-15 . . . . . . . . . . With NB Rim and Aluminum Recessed Grate-21 . . . . . . . . . . With A.R.C. Grate and 4" (100) DIA A.R.C. Funnel-22 . . . . . . . . . . With A.R.C. Grate and 6" (150) DIA A.R.C. Funnel-25 . . . . . . . . . . With A.R.C. Grate and 8 1/4(210) x 3 1/4(83) x 4 1/2"(115) High Oval A.R.C. Funnel-26 . . . . . . . . . . With A.R.C. Grate and 6(150) x 2 1/2(64) x 1"(25) High Oval A.R.C. Funnel-41 . . . . . . . . . . With A.R.C. Solid Cover-42 . . . . . . . . . . With A.R.C. 1/2 Solid Cover-44 . . . . . . . . . . With A.R.C. Solid Cover with 2 1/2" (64) DIA Center Hole
SANI-CEPTOR® ACID RESISTANT COATEDFLOOR & INDIRECT WASTE DRAINS
A.R. COATED NON-TRAFFIC TOPS8" (205) SQUARE TOP - MEDIUM RECEPTORS
FUNCTION: Used in kitchens, hospitals, food markets, restaurants, schools and all types of food handling areas not subjectto foot or other traffic where the ultimate in sanitation is desirable and a medium capacity receptor is required.
FEATURES, OPTIONS & ORDERING INFORMATIONREGULARLY FURNISHED: Cast Iron Flanged Receptor with Seepage Holes, Acid Resistant Coated Interior, and Loose SetAcid Resistant Coated Cast Iron Grate. Aluminum Dome Bottom Strainer or White ABS Sediment Bucket as Indicated byFigure Number. VARIATIONS:
Aluminum Flat Bottom Strainer -FBSFlashing Clamp -CLess Flange (Specify Fig. 3415, 3416)Polished Aluminum Dome Bottom Strainer -PDBSL Speedi-Set Service Weight LXH Speedi-Set Extra Heavy
OPTIONAL MATERIALS:All Duco Cast Iron Receptor and Grate -CIAll Galvanized Receptor and Grate -G
Fig. 3410C . . . . . . . . . . CAULK OUTLET . . . . . . . . . . Fig. 3411CFig. 3410Y . . . . . . . . . NO-HUB OUTLET . . . . . . . . . . Fig. 3411Y
Free Area11 SQ IN
(71) SQ CM
A (Pipe Size) = 02(50), 03(75) or 04(100)
3410, 3411
3410
, 341
1VG
DJD
SJM
9-19
-85
NO
NE
S341
0K
WITH DOME BOTTOM STRAINER WITH SEDIMENT BUCKET
NOTE: Dimensions shown inparentheses are in millimeters.
NOTE: This grate is not recommended forany type of traffic including pedestrian traffic.
CLG 12-3-98 Added Note CMDH 01/20/11 Updated Logo JJ TWJ 6-10-14 Revised Reg. Furn., Var. TBW TWKK 8-4-14 Revised Variations TBW CL
JAY R.SMITH MFG. CO.®
MEMBER OF MORRIS GROUP INTERNATIONAL™POST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 www.jrsmith.com
CUSTOMERDRIVEN
SMITH®
MEMBER OF:
®
ASPE®
SANITARY
EN G IN E E RINGPrevention Rather Than Cure
SINCE 1926