PLEATFIL™ PGPPleated polypropylene filter cartridge

Pleatfil™ PGP filter cartridges are cost effective, Beta

5000 absolute rated pleated polypropylene filters.

The fully welded construction of PGP grade filters,

with no resins, binders, or adhesives, makes them

particularly suitable for chemical, food & drink,

and high-purity water filtration applications where

chemical compatibility and minimal levels of

extractables are crucial. Pleatfil™ liquid filter cartridges

are fully validated and recorded in the product validation

guide for Pleatfil™.

PLEATFILTM PGP

TM

using the industry standard single pass OSU-F2 test

procedure with ISO 12103 part 1 A2 Fine and A4

Coarse test dust in water.

Manufactured in Europe from 100% virgin

Thermal bonded construction eliminates the

requirement for adhesives, maintaining product

integrity in demanding applications and minimising

Food & Biological Safety

All materials conform to the relevant requirements of

FDA CFR21 part 177, USP Plastics Class VI and EC

1935/2004.

range of applications, and are used for the

end products.

Pleated polypropylene filter cartridge

Removal ratings from 0.2 to 100 micron

One-piece construction up to 40”

Fully welded construction

High surface area, up to 0.6 m²/10”

Full range of bonded end caps available

Low pressure drop

Long life, high dirt-holding capacity

Materials conform with FDA 21CFR part 177,

and EC 1935/2004

A full validation guide is available upon request

• •• ••• • • •••

•

Retention characteristics

have been determined by a single-pass technique

using suspensions of ISO 2103 Part 1 A2 Fine and

A4 Coarse test dust in water.

TM

Media

Code

PGP020

PGP050

PGP01

PGP02

PGP05

PGP10

PGP25

PGP50

PGP75

PGP100

99.98%

Bèta 5000

0.20

0.50

1.0

2.0

5.0

10.0

25.0

50.0

75.0

100.0

99.90%

Bèta 1000

< 0.20

0.45

0.75

1.7

3.5

8.0

15.0

29.0

55.0

85.0

99%

Bèta 100

-

0.35

0.55

1.5

2.0

4.8

12.0

25.0

40.0

75.0

90%

Bèta 10

-

0.3

0.4

1.2

1.5

2.5

8.0

15.0

35.0

70.0

Dimensions (nominal)

Outside Diameter: 69 mm

Inside Diameter: up to 32 mm

Lengths: 5” to 40”

Operating Conditions

Recommended Maximum ∆P PP core 4.0 bar @ 20 °C

PP core 1.2 bar @ 65 °C

Recommended change-out

PP core 2 bar ∆P @ 20 °C

Maximum service life 12 months

Maximum continuous operating T:

80 °C with PP centre core

Sterilisation and sanitisation

Hot water: 90 °C for 30 minutes @ max 0.2

bar dp

Materials of Construction

Filter Medium: PolypropyleneDrainage layers: PolypropyleneInner Core: PolypropyleneOuter Core: PolypropyleneEnd Caps: PolypropyleneGaskets & O-rings: various materials

Technical Data Pleatfil TM PGP

A comprehensive range of thermally welded end caps are available to suit most existing installations.

:

solutions with a viscosity of 1 centipoise.

20

15

10

5

00 5 10 15 20 25

Flow (l/min)

Dif

fere

nti

al P

ress

ure

(m

bar)

PGP 25 / 50

PGP 75 / 100

Viscosity (CPS) 1 100 200 400 600 800 1000 1500 2000 4000 6000 8000 10000

Conversion factor 1 .85 .58 .35 .25 .17 .16 .11 .08 .05 .035 .026 .021

PGP 10

Fusion bondingInner coreSupport layerFilter mediaDrainage layerOuter supportTop end cap / adaptor

1

2

3

4

5

6

7

8

4

5

5

6

3

28

7

2

1

Dif

fere

nti

al P

ress

ure

(m

bar)

60

50

40

30

20

10

00 5 10 15 20 25

PGP020

PGP050

PGP01PGP02

Flow (l/min)

PGP05

PLEATFILTM PGP

High-quality cartridge construction ensures

consistent performance

melt-blown polypropylene medium to minimise

The structurally stable medium eliminates the risk of

channelling and particle unloading even under impulse

materials are carefully pleated and seam-bonded to avoid

Quality Assurance & Traceability

environment by staff fully gowned to minimise any risk of

contamination during production.

Filter Housings

Filter housings are subdivided into two main categories:

Housings for (pressurised) air & other gases.

Address

Techno Filter B.V.

Johan Enschedeweg 72

1422 DR Uithoorn

Contact

Telephone: +31(0)297 - 524 131

Faxnr: +31(0)297 - 524 333

CoC: 54868718

VAT registrationnr: NL 851471559B01

The Netherlands

the European regulations of the Pressure Equipment

and vacuum applications.

Techno Filter designs and supplies:

sanitary and industrial grades.

“lenticulars” in sanitary grades.

industrial grades.

from 0.4 up to appr. 1250 microns.

PED 97/23 standard: categories III and IV. This means

or questions about custom housings, please contact

Techno Filter.

•

•

•

•

•

•

•

PGP00.1