Plastics Books - Hanser Fachbuch

PlasticsBooks2011 - 2012

22

If you are a resident of one of the countries below,

please adress all orders to:

AustraliaD.A. Information Services Pty Ltd.Sandra Stringer648 Whitehorse Road3132 MitchamAustraliaTel.: +61/3 92 10 77 77Fax: +61/3 92 10 77 [email protected]

ChinaRingier Trade Publishing LimitedMike Hay401-405, 4/F New Victory House93-103 Wing Lok Street, Sheung WanHong KongTel.: +85/23 69 87 88Fax: +85/28 69 59 [email protected] www.industrysourcing.com

DenmarkAalborg CenterboghandelFibigerstraede 159220 Aalborg OstDenmarkTel.: +45/98 15 89 22Fax: +45/98 15 28 [email protected]

HungaryProspero’s Books Budapest Ltd.Eszter FriedmannWeiner Leo U 201066 BudapestHungary

IndiaAllied Publishers Pvt. Ltd.Mr. R.N. PurwarI/13-14, Asaf Ali Road110 002 New DelhiIndiaTel.: +91/11 23 23 90 01Fax: +91/11 23 23 59 [email protected]

Sci-Tech Books and PeriodicalsMr. P.D. Kamat106, Parul ApartmentsVeera Desai RoadAndheri (West)400 053 MumbaiIndiaFax: +91/22 26 73 54 [email protected]

Techniz Books International4/12, Kalkajee ExtensionOpp. nehru Place10019 New DelhiIndiaTel.: 0091/11 26 28 47 90Fax.: 0091/11 26 47 36 11Mail: [email protected]

IranFaravaran Publication Distributor Co.PO Box 14665-1366TehranIranTel: +98/21 88 55 32 71Fax: +98/21 88 55 20 [email protected]

IsraelCom.books Ltd.Ms. Ziva Beech13, Beit Alpha Street67219 Tel AvivIsraelTel.: +972/3 56 21 00 2Fax: +972/3 56 21 00 [email protected]

ItalyMeBSSabrina GandolaVia Nicola D’Apulia 1120127 MilanoItalyTel: +39 02 26 14 90 08Fax: +39 02 26 14 96 [email protected]

PakistanMirza Book AgencyQasim Mahmood Mirza65-Sharah-e-Quaid-e-AzamLahore-54000PakistanTel. 0092/42 73 53 601Fax 0092/42 57 63 714Mail: [email protected]

Tahir M. LodhiPublishers Consultants &Representatives14-G, Canalberg H.S.53700 LahorePakistanTel.: 0092/42 54 37 947Fax.: 0092/42 54 37 948Mail: [email protected]

MalaysiaUBSD Distribution SDN BHDBandar Puchong Jaya3F-15, IOI Business Park 1Persian Puchong Jaya47170 Puchong, SelangorMalaysiaTel.: 00603/80 76 30 42Fax.: 00603/80 76 31 [email protected]

Singapore, Indonesia, BruneiBook Editions (S) Pte Ltd.Richard Mah22 Sin Ming Walk # 10-01575571 SingaporeTel.: +65/64 52 05 52Fax: +65/64 52 02 [email protected]

Alkem Company (S) Pte Ltd.Adrian Tan1, Penjuru Close608617 SingaporeTel.: +65/62 65 66 66Fax: +65/62 61 78 [email protected]

SlovakiaMale centrum AcademicBookshopAnton ZemlickaCernysevskeho 3585101 BratislavaSlovakiaTel.: +421/25 24 99 82 6Fax: +421/25 29 31 12 [email protected]

SloveniaBookshop Lux LibrisAndrej PucnikTrg Osvobodilne fronte 13 A1000 LjubljanaSloveniaTel.: +386 (0) 1 232 20 26Fax: +386 (0) 1 232 10 [email protected]

SpainNova Agora S.L.Sandra AguileraAmadeus Vives 20-2208750 Molins de ReiSpainTel.: +34/93 68 02 02 7Fax: +34/93 68 02 03 [email protected]

United KingdomApplied Market Information Ltd.Phil Cotterell45-47 Stokes CroftAMI HouseBristol BS1 3QPUnited KingdomTel.: + 44/1179 24 94 42Fax: + 44/1179 89 21 [email protected]

Smithers Rapra LimitedLavinia KieransShawburyShrewsburyShropshire SY4 4NRUnited KingdomTel: +44/1939 252313 Fax: +44/1939 251118 [email protected] www.rapra.net

TaiwanUnifacmanu Trading Co., Ltd.Céline Li4F, No. 91, Ho-Ping East Road,Sec. 1TaipeiTaiwanTel.: +886/22 39 42 74 9Fax: +886/22 39 43 10 [email protected] www.winjoin.com.tw

ThailandSE-Education Public CompanyLimitedBangna-Trad Road Km 4.5BangnaForeign Book Division, 23rd Floor10260 BangkokThailandTel.: 0066/27 39 85 55Fax: 0066/27 51 55 90Mail: [email protected]

USAHanser Publications LLCValerie Lauer6915 Valley AvenueCincinnati, OH 45244USATel.: 001/513 527 88 [email protected]

If you are a resident of one of the countries below, please adress all orders to:

2

For all other countries:Carl Hanser VerlagP.O. Box 86 04 2081631 MunichGermanyTel.: +49/89/99 830- 333Fax: +49/89/99 830- [email protected] www.kunststoffe.de

All prices recommended prices only.Prices valid from 1.10.2010 onwards.

33

DESIGNProduct Design ..............................................................................4Tool Design ...................................................................................6

PROCESSING & MANUFACTURINGGeneral Overview ......................................................................... 10Mixing & Compounding ................................................................. 13Injection Molding ........................................................................ 15Extrusion .................................................................................... 21Blow Molding .............................................................................. 26Thermoforming ............................................................................ 28Other Processes ........................................................................... 30

MATERIALSGeneral Overview ......................................................................... 34Rubber ....................................................................................... 39Coatings ..................................................................................... 42Fibers & Films.............................................................................. 43Additives & Colors ........................................................................ 44Recycling .................................................................................... 46Other Industry Applications ........................................................... 45

POLYMER SCIENCETesting & Analytical Methods ......................................................... 48Physics & Chemistry ..................................................................... 50

REFERENCEDictionaries ................................................................................ 52Plastic Pocket Power Series ............................................................ 53

MAGAZINESHanser Magazines ........................................................................ 55

INDEXTitle .......................................................................................... 56 Author ....................................................................................... 60

ORDERINGFax Sheet ................................................................................... 62

Contents

4

E. Campo

The Complete Part Design HandbookFor Injection Molding of Thermoplastics

ISBN 978-3-446-40309-3©2006, hardcover, 299,-891 pages/995 figures/68 tables

This indispensable, all-inclusive reference guide to plastic part design was compiled with the product designer in mind, who is looking for more detailed information on plastic resins, the rules and geometries underlying their use in product design, and the advantages and limitations of their use in industrial applications. The designer will also find valuable advice on resin and tool selection and processing parameters that allow fast and successful product development and manufacture.

Thousands of hours of research and cross referencing have gone into the completion of this work. In addition, the “hands-on” knowledge of a plastics expert with more than 35 years experience is incorporated.

P. Tres

Designing Plastic Parts for Assembly6th Edition

ISBN 978-3-446-40321-5 ©2006, hardcover, 89,90 311 pages/270 figures/45 tables

This book provides an excellent tool for both seasoned part designers and novices to the field, facilitating cost-effective design decisions and ensuring that the plastic parts and products will stand up under use.

The detailed, yet simplified discussion of material selection, manufacturing techniques, and assembly procedures enable the reader to evaluate plastic materials and to adequately design plastic parts for assembly.

The book describes good joint design and implementation, the geometry and nature of the component parts, the types of load involved, and other basic information necessary in order to work successfully in this field. Throughout, the treatment is practice-oriented and focused on everyday problems and situations.

G. Erhard

Designing with PlasticsISBN 978-3-446-22590-9 ©2006, hardcover, 129,90530 pages/525 figures

Designing with Plastics is an indispensable tool for every engineer and designer working with plastic materials. It assists in the development of plastic parts that are not only functional and esthetically pleasing but also manufacturable while meeting ever increasing end-use requirements.

The short but concise introduction into the specific properties of this material class focuses on the practical needs of the designer and lays the foundation for the following in depth discussion of part design suitable for production and the intended end-use application. Numerous detailed examples highlight practical tips and rules of thumb for successful part design.

“... if the principles con-tained in this book are used during the design process, there will be fewer head-aches right from the start.”

—Injection Molding

Product Design

DESIGN

5

P. Bonenberger

The First Snap-Fit HandbookCreating and Managing Attachments for Plastics Parts 2nd Edition

ISBN 978-3-446-22753-8 ©2005, hardcover, 99,90320 pages/183 figures/45 tables

The ‘system level’ knowledge and design skills needed to create good snap-fit interfaces existed in the minds of self-taught snap-fit experts but was not captured in the literature.

New designers of plastic parts wishing to use snap-fit had nowhere to turn unless they were fortunate enough to have access to an experienced snap-fit designer. This book organizes and presents all design aspects of snap-fits with an emphasis on the systems level thinking required to create world-class attachments. Beginning, as well as experienced, product designers will find the information they need to develop snap-fits more efficiently and avoid many common snap-fit problems.

R. Malloy

Plastic Part Design for Injection MoldingAn Introduction 2nd Edition

ISBN 978-3-446-40468-7©2010, hardcover, 89.90568 pages/476 figures/28 tables

This overview of the design process for injection molded plastic parts describes an integrated approach to part design and material selection and will assist the designer in the development of parts that are functional, reliable, manufacturable, and aesthetically pleasing. The book covers not only concurrent engineering and design for manufacturability concepts, but in its new edition also addresses design for enhanced recyclability as well as the opportunities - and limitations - of implementing recycled material streams into the manufacturing process.

The new and expanded version of this classic book will prove to be an essential tool to achieving economic and functional design goals.

J. Rotheiser

Joining of PlasticsHandbook for Designers and Engineers 3rd Edition

ISBN 978-3-446-40786-2©2009, hardcover, 129,90624 pages

This completely updated handbook emphasizes the relationship between the assembly methods, the materials, and the plastics manufacturing processes, thus enabling the reader to identify the best design/assembly method for a given application. A new chapter on laser welding of plastics has been added. All principle fastening and joining methods used to assemble plastic parts today are described with their particular advantages and disadvantages. Assembly method limitations for a given material and/or a given molding process are discussed in great detail. This how-to book offers a wealth of hard-to-find, detailed information.

Partial Contents: Rapid Guidelines for Assembly of Plastics. Designing for Efficient Assembly. Cost Reduction in Assembly. Design for Disassembly and Recycling.

Product Design

DESIGN

6

N. Rao, G. Schumacher

Design Formulas for Plastics Engineers2nd Edition

ISBN 978-3-446-22674-6 ©2004, softcover, 69.90176 pages/135 figures

The second edition of this well-received book presents a summary of important formulas and their applications to solve design and processing problems. The formulas are classified according to specific fields, rheology, thermodynamics, heat transfer, and part design. Each chapter covers the relevant relations with detailed examples. In addition, this work contains new, straightforward, practical relationships that have been developed and tested in recent years for solving design problems in the area of extrusion and injection molding.

Contents: Formulas of Rheology. Thermodynamic Properties. Formulas for Heat Transfers. Designing Plastic Parts. Designing Extrusion Equipment. Designing Injection Molding Equipment.

H. Rees

Understanding Product Design for Injection MoldingISBN 978-3-446-40308-6 ©1996, softcover, 39,90116 pages/64 figures

This primer offers assistance when selecting the proper material for any product and determining whether injection molding is the process best suited for the application.

Contents: Plastic Product Design. Making a New Product. New Injection Molding Designs. Designing a Product. Product Shape. Designing for Assemblies.

P. Unger

Hot Runner TechnologyISBN 978-3-446-50554-4©2006, hardcover, 129,90249 pages/210 figures/25 tables

Quality and profitability of injection molding operations can be considerably influenced by the hot runner system. The many variations and design principles of hot runners are material-dependent and therefore not universally applicable. Knowing about and recognizing these limitations will make or break a molder’s success. This book provides a comprehensive overview of hot runner techno-logy, advantageous design principles, and applications. It includes the necessary basics as well as many proven designs and application examples.

Contents: Heat Technology. Hot Runner Components. Heating Manifold Blocks. Heating of Hot Runner Nozzles. Temperature Measuring and Controlling. Material Behavior under Stress. Corrosion and Wear. Screw Connections and Material Selection. Basic Plastics Technology. Maintenance and Storage Molds. Design. Suppliers of Hot Runner Systems.

Tool Design

DESIGN

7

H. Rees, B. Catoen

Selecting Injection MoldsWeighing Cost versus Productivity

ISBN 978-3-446-40308-6©2006, hardcover, 99.90240 pages/213 full-color figures/12 tables

This book explains to the mold designer the importance of knowing the expected productivity of the mold and how this information affects the cost of the planned mold and the cost of the molded product. It suggests many approaches to reduce mold cost and also to improve productivity by often just simple design changes. Above all, it emphasizes again and again that the ultimate goal is not to procure the lowest cost but to produce the lowest cost product.

Contents: How to approach selection of the mold features. How productivity affects mold selection. How selection of design features affects mold cost. How to reduce mold and product cost by simple design changes. How to approach estimating mold cost.

A. Gebhardt

Understanding Additive ManufacturingRapid Prototyping - Rapid Tooling - Rapid Manufacturing

ISBN 978-3-446-42552-1, ©2011 69,90approx. 160 pages

Additive Manufacturing (AM) is the worldwide used term for layer oriented or generative manufacturing which originally was introduced at the end of the 1980s as Rapid Prototyping. Within the last 20 years it has developed dramatically. Today it is not just a valuable tool for making models and prototypes, but a manufacturing method for final parts as well as for mold inserts. It spreads throughout all disciplines and branches of industry, from art to medicine and from car manufacturing to aerospace engineering. AM is about to revolutionize the manufacturing technology in general. This book is designed as a supporting material not only for special courses on advanced manufacturing technology, but for up-dating the content of traditional manufacturing courses.

H. Rees

Understanding Injection Mold DesignISBN 978-3-446-21587-0 ©2001, softcover, 39.90127 pages/36 figures

This book provides the ground rules for designing injection molds and explains the basic mold principles regardless of what size and type of product is to be injection molded.

Contents: Starting New in the Mold Design Field. The Basics of an Injection Molding Machine. Understanding the Basics of the Injection Mold. Before Starting to Design a Mold: Machine Specification, Mold Design, Preload, Mold Material Selection, Stack Molds, Mold Layout and Assembly Drawings. Review and Followup. Typical Examples. Estimating of Mold Costs. Machining, Mold Materials, and Heat Treatment.

Tool Design

DESIGN

8

D. Kazmer

Injection Mold Design EngineeringISBN 978-3-446-41266-8 ©2007, hardcover, 99,90444 pages/280 figures/53 tables

This book provides a vision and structure to finally synergize all the engineering disciplines that converge in the mold design process. The topics are presented in a top-down manner, beginning with introductory definitions and the “big picture” before proceeding to layout and detailed design of molds.

The book provides very pragmatic analysis with worked examples that can be readily adapted to real-world mold design applications. It helps students and practitioners to understand the inner workings of injection molds and encourage them to think “outside the box” in developing innovative and highly functional mold designs.

H. Rees

Mold Engineering2nd Edition

ISBN 978-3-446-21659-4©2002, hardcover, 129,90712 pages/554 figures

Injection molds for thermoplastic molding materials and their performance are covered in detail in this book for mold designers, molding machine technicians, and design engineers. Guidelines are supplied for the design of molds, from product drawing to complete mold assembly drawing, and more.

Partial Contents: Basic Functions. Requirements. General Guidelines. Layout. Operation Sequences. Shrinkage. Surface Tolerances. Gates and Runners. Venting. Ejection. Cooling. Heat Expansion. Stack Molds. Materials Specifications. Plates. Metal Fatigue. Screws. Parts Handling. Air and Oil Hydraulic Actuators. Rules and Calculations for Designers.

K. Stoeckhert, G. Mennig

Mold-Making Handbook2nd Edition

ISBN 978-3-446-18257-5©1999, hardcover, 149,90583 pages/492 figures/48 tables

This new edition of Stoeckhert’s classic provides all fundamental and engineering aspects of mold construction and manufacturing. Completely revised, this edition includes the latest developments in technology, such as CAD and rapid prototyping.

Partial Contents: Molds for Various Processing Methods (Injection, Compression and Transfer Molds, Blow Molds, Thermoforming and Rotational Molds, Molds for Processing Reaction Resins, EPS and PU, Prototyping Molds. Materials (Steels, Bronzes, Aluminum and Zinc Alloys, Materials for Rapid Tooling. Manufacturing and Machining Methods (CIM in Metal Working, EDM, Electroformed Mold Cavities, Polishing, Hobbing, Surface Treatment, Cast Bronze and Light Alloy Molds.

Tool Design

DESIGN

9

G. Menges, W. Michaeli, P. Mohren

How to Make Injection Molds3rd Edition


This classic covers all aspects of injection mold design and manufacturing including material selection, general mold design, fabricating cavities and cores, dimensioning for mechanical and thermal design, and venting.

Partial Contents: Mold Making Techniques. Mold Costs. Runner Systems. Gates. Venting of Molds. Heat Exchange. Shrinkage. Mechanical Design. Shifting of Cores. Ejection. Alignment. Computer Assisted Mold Design. Maintenance. Mold Standards. Correction of Molding Defects. Special Processes/Molds.

J. Beaumont

Runner and Gating Design HandbookTools for Successful Injection Molding 2nd Edition

ISBN 978-3-446-40765-7©2007, hardcover, 129,90324 pages/331 full-color figures/10 tables

For the first time, both the art and the science of designing runners and gates are presented in a concise format. Tried and true runner and gating design techniques successfully used with various materials and molding applications are described together with cutting-edge new technologies. This handbook helps determine the optimum design, when to use what type of runner systems, and how to isolate molding problems generated from the gate and runner vs. other molding issues. Full-color 3-D graphics, illustrations and photographs as well as charts, checklists, troubleshooting guides, and contributions from the industry’s leading expert John Bozzelli complete this handbook.

P. Unger

Gastrow Injection Molds130 Proven Designs 4th Edition

ISBN 978-3-446-40592-9 ©2006, hardcover, 129,90345 pages/400 figures

Designing the perfect mold is probably the most challenging task in plastics processing, especially in injection molding. The mold determines the quality, performance, and the profitability of a plastic part. Neither modern computer technology nor sophisticated CAE software can substitute the experience of the practicing mold engineer. This is why the “Gastrow” is so special to plastics engineers: 130 mold designs are presented in this extensively revised edition of the great classic in mold making. Each of the case studies was actually built, tested, and run successfully in production. The book is written by practitioners, describing problem solving in the design and the manufacture of injection molds. The wealth of information includes rules of thumb, design details, and practical tips invaluable for everyone involved in this field.

“... [The 2nd Edition is] an example of how books should be written ... [it] will be used by molders, mold designers and moldmakers and will become a standard.”

Polymer News

Tool Design

DESIGN

1010

M. Ezrin

Plastics FailureCause and Prevention


Plastics failure, to a certain extent, is the result of a phenomenal increase in the number and variety of applications in relatively few years. This book focuses on actual field and product failures. The treatment is comprehensive, emphasizing cause and prevention. The concept of the interdependence of material, design, and processing is applied to all examples and cases. The “how to” of prevention is brought out as a logical extension of the cause of failure.

Partial Contents: Nature, Causes, and Consequences of Plastics Failure. Fundamental Materials Variables Affecting Processing and Product Performance or Failure. Failures Related to Design and Material Selection. Processing-Related Factors to Failure. Failure Related to Service Conditions. Failure Analysis and Test Procedures. Quality Control.

A. Gebhardt

Rapid PrototypingISBN 978-3-446-21259-0 ©2003, hardcover, 99,90379 pages/220 figures/57 tables

Rapid prototyping technologies have emerged into an effective and indispensable tool for fast product development. Focusing on the practitioner, this book covers the basics of rapid prototyping and introduces the properties and special features of industrially available prototypers. The rapid prototyping methods are compared to traditional machining methods and an entire chapter is devoted to rapid tooling. Numerous industrial case studies complete this book.

Partial Contents: Data Transfer and Rapid Prototyping Interfaces. Model Types and Model Classes. Rapid Prototyping Processes. Rapid Tooling for Soft- and Hard Tooling. Post Processing and Finishing.

D. Kazmer

Plastics Manufacturing Systems EngineeringISBN 978-3-446-42014-4 ©2009, hardcover, 99,90520 pages/321 figures/76 tables

Plastics manufacturing is a highly interdisciplinary endeavor requiring knowledge related to materials science, physics, engineering, and management. Because of this diversity, the plastics process engineer interacts with many stakeholders, including customers, designers, materials suppliers, machine builders, mold/die suppliers, systems integrators, operators, quality engineers, and managers. With so many stakeholders involved, it isn’t surprising that many plastics manufacturing processes are not precisely engineered systems. The resulting processes can be poorly designed, requiring too much investment to achieve too little productivity. This book was written for plastics processing engineers, but it is also highly useful to others involved with plastics manufacturing who are performing process development, research, and even machinery design.

General Overview

PROCESSING & MANUFACTURING

1111

J. Shoemaker

Moldflow Design GuideA Resource for Plastics Engineers


This book helps plastics designers and engineers solve common problems afflicting plastic parts and molds. Moldflow pioneered injection molding simulation in 1978 and has helped over 5,000 manufacturers make better parts faster and with higher profit. Whether you use Moldflow software or not, this guide is an indispensable tool to understanding plastic flow, CAE analysis and results, and cooling and warp effects to aid in the successful design and manufacture of parts and molds.

The book includes an overview of polymer flow behavior and the injection molding process, design principles to facilitate integrated part and mold design, and examples of how Moldflow technology can be used both to solve problems and optimize design and manufacturing.

W. Michaeli, H. Greif, L. Wolters, F. Vossebürger

Training in Plastics Technology2nd Edition

ISBN 978-3-446-21344-9 ©2001, softcover, 49,90180 pages/143 figures

Use this authoritative source book to guide newcomers in the plastics industry. Training in Plastics Technology is a text and workbook that provides an introduction to the world of plastics. This book is divided into educational units each of which covers a distinct subject area. Key questions at the beginning of each lesson help the reader approach the subject matter with certain questions in mind. Review questions at the end of each lesson test the knowledge acquired. The answers can be checked against the lists of correct answers at the end of the book. This comprehensive best-selling reference provides the fundamental information you’ll need to understand both processing and applications.

T. Osswald, E. Baur, S. Brinkmann, K. Oberbach, E. Schmachtenberg

International Plastics HandbookThe Resource for Plastics Engineers 4th Edition

ISBN 978-3-446-22905-1©2006, hardcover, 99,90920 pages/450 figures/177 tablesIncludes eBook

This comprehensive handbook provides everything there is to know about plastics. From material properties to machines, processing, and applications, the reader will find detailed information for the successful implementation of new materials and technologies. This concise, modern reference not only explains the basic facts and interrelationships about plastics but also offers a practical guide for engineers to succeed in today’s challenging global industrial world.

eBook Bonus: Included free with the purchase of this book is an online access code for the electronic version.

General Overview


1212

T. Osswald

Understanding Polymer Processing ISBN 978-3-446-42404-3©2010, softcover, 69,90304 pages

This book provides the background needed to understand not only the wide field of polymer processing, but also the emerging technologies associated with the plastics industry in the 21st Century. The book combines practical engineering concepts with modeling of realistic polymer processes. It is divided into three sections that provide the reader sufficient knowledge of polymer materials, polymer processing, and modeling. Understanding Polymer Processing is intended for the person who is entering the plastics manufacturing industry and as a textbook for students taking an introductory course in polymer processing. This three-part book also serves as a guide to the practicing engineer when choosing a process, determining important parameters and factors during the early stages of process design, and when optimizing such a process. Practical examples illustrating basic concepts are presented throughout the book.

T. Osswald, J. Hernandez

Polymer ProcessingModeling and Simulation


This book provides a polymer processing background to engineering students and practicing engineers. It addresses traditional polymer processing as well as emerging technologies. Many applications are presented through examples and illustrations, which also serve the practicing engineer as a guide when determining important parameters and factors during the design process or when optimizing a process.

Contents: Polymer Material Science. Processing Properties. Polymer Processes. Processing Fundamentals. Dimensional Analysis and Scaling. Transport Phenomena in Polymer Processing. Analyses Based on Analytical Solutions. Numerical Techniques. Introduction to Numerical Analysis. Finite Differences Method. Finite Element Method. Boundary Element Method. Radial Functions Method.

R.J. Del Vecchio

Understanding Design of ExperimentsISBN 978-3-446-18657-6 ©1997, softcover, 49,95188 pages/42 figures/5 tables

This book explains the basics underlying designed experiments, supplies instructions on how to use several families of convenient designs, and gives an overview on assorted subtopics of the large field that comprise the design of experiments.

Providing an introduction to the design of experiments, this text leads the reader step by step through the basic concepts and practices of this methodology. Special coursework or degree is not necessary, because this book uses uncomplicated language and readily understandable examples to introduce ample background theory. The focus is on providing the reader with working skills.

General Overview


1313

I. Manas-Zloczower

Mixing and Compounding of PolymersTheory and Practice 2nd Edition

ISBN 978-3-446-40773-2 ©2009, hardcover, 249,001188 pages/1213 figuresIncludes eBook

Completely updated, the second edition of this classic handbook provides a representative state-of-the-art review of mixing and compounding technology in polymer processing. It covers all aspects of mixing, from the basic principles to the various practical applications, with due consideration to material properties and mixing devices.

Partial Contents: Part I: Mechanisms and Theory Part II: Mixing Equipment - Modeling, Simulation, Visualization Part III: Material Consideration, Properties and Characterization Part IV: Mixing Practices

eBook Bonus: Now get full-text search capability in this treasure trove of information for the plastics professional. Included free with the purchase of this book is an online access code for the electronic version.

J. White, A. Coran, A. Moet

Polymer MixingTechnology and Engineering


There has been an increase in the development and production of new polymer blends and the preparation of compounds of polymers of carbon black, various fibers, and inorganic particles. These developments have led to a blending/compounding industry, which sits between the polymer producers and the manufacturers of shaped products such as injection molders. This book provides a broad-based examination of the characteristics of polymer blends and compounds and describes the mechanisms of mixing and blending technology and flow mechanisms in mixing equipment.

Partial Contents: Mechanisms of Mixing. Overview of Mixing Machinery. Batch and Internal Mixers. Single Screw Extruder. Buss Kneaders. Co-Rotating Single Screw Extruders. Counter-Rotating Twin Screw Extruders. Continuous Mixers. Feeding and Feeders.

C. Rauwendaal

Polymer MixingA Self-Study Guide


This book covers the fundamental aspects of polymer mixing, as well as modern mixing equipment. It emphasizes the basic mechanisms involved in the different mixing processes with a quantitative description of each process. The end of section questions let readers evaluate progress.

Contents: Evaluation of Mixtures. Distributive Mixing. Dispersive Mixing. Single Screw Extruders. Twin Screw Extruders. Internal and External Mixers. Static Mixing Devices.

Mixing & Compounding


1414

R. Wildi, C. Maier

Understanding CompoundingISBN 978-3-446-18494-7©1998, softcover, 39,90201 pages/159 figures/5 tables

Intended as a primer for anyone associated with compounding operations who is not an expert, this book gives a general overview of the process and a description of the what and how of the major compounding classes and unit operations.

Contents: What Is Compounding. Pre-Compounding Operations. Compounder Types. Unit Operations. Post-Compounding Operations. Evaluation of Compounds.

A. Müller

Coloring of PlasticsFundamentals – Colorants – Preparations


This book describes the various aspects of coloring plastics, such as the construction of the processing machine, the processing technology, quality assurance of the raw materials and final products, toxicology of the raw materials, and the legal aspects from the handling of all ingredients during the production of a color preparation to the processing of plastic parts. It also includes the safe use of the plastic products in their specific application.

Partial Contents: Methods Used to Color Plastics. Requirements for Color Preparations. Composition of Color Preparations. Colorants for Polymers. Additives for Polymers. Processing Errors and Their Elimination. Quality Assurance. Mold Construction. Legislation. List of Colorants.

W. Baker, C. Scott, G. Hu

Reactive Polymer BlendingISBN 978-3-446-312-4©2001, hardcover, 129,90400 pages/150 figures/70 tables

This book provides a comprehensive overview of the general principles involved in successful reactive blending. Pioneering work on several key issues including copolymer formation, interface development, and morphology are covered.

Contents: Reactive Blending with Immiscible Functional Polymers. Key Role of Structural Features of Compatibilizing Additives in Reactive Blending. Morphological and Rheological Aspects of Reactive Polymer Blending. Reactive Blending in Screw Extruders. Extrusion Equipment for Reactive Blending. Rubber Toughening of Polyamides by Reactive Blending. Compatibilization Using Low Molecular Weight Reactive Additives.

Mixing & Compounding


1515

S. Kulkarni

Robust Process Development and Scientific MoldingTheory and Practice

ISBN 978-3-446-42275-9 ©2010, hardcover, 119,00272 pages

The book introduces the concept of scientific processing for injection molding. A section on design of experiments for injection molding provides insight to the cosmetic and dimensional process windows. This book also includes a plan to release qualified molds into production, trouble shooting tips, and topics that impact a robust process such as the use of regrind, mold cooling, and venting.

Partial Contents: Introduction to Scientific Processing for Injection Molding. Introduction to Polymers. Polymer Rheology. Plastic Drying. Plastic Materials, Fillers and Additives. Injection Molding. Scientific Processing and Scientific Molding. Design of Experiments for Injection Molding. Types of Process Windows and Alarm Limits. Quality Control Concepts. Production Release of the Molds.

M. Kamal, A. Isayev, S. Liu

Injection MoldingFundamentals and Applications

ISBN 978-3-446-41685-7©2009, hardcover, 249,00952 pages/617 figuresIncludes eBook

This book surveys the state of the science and technology of the injection molding process. It represents a comprehensive, balanced mix of practical and theoretical aspects for a wide range of injection molding applications. The authors of the 21 chapters are experts and leaders in their respective areas of specialization in the injection molding field. While it is not possible to cover all aspects of such a dynamic growing field, the reader will find sufficient information and background to become acquainted, at various levels of depth, with key components of the science and technology of injection molding.

eBook Bonus: Now get full-text search capability in this treasure trove of information for the plastics professional. Included free with the purchase of this book is an online access code for the electronic version.

J. Avery

Gas-Assist Injection MoldingPrinciples and Applications


This book provides in-depth coverage of all aspects of designing, developing, and manufacturing parts using gas-assist injection molding, comparing this relatively new technology to other possible manufacturing methods. The reader will gain an understanding of how to identify the specific version of this technology best suited for his/her application, as well as design and tooling details required to optimize cost and performance.

Contents: Overview. Techniques of Gas-Assist Injection Molding. Gas-Assist Design. CAE Molding Simulation. Guidelines for Designing and Manufacturing Tools for Gas-Assist Injection Molding. Manufacturing with Gas-Assist Injection Molding. Case Studies.

Injection Molding


1616

C. Rauwendaal

SPC in Injection Molding and Extrusion2nd Edition


Many SPC training programs are taught by people that are familiar with statistics but know little about process technology. Successful implementation of SPC requires an understanding of SPC as well as process know-how. This book teaches not only the principles of SPC but also basic injection molding and extrusion process technology. It also includes lists of commercially available software for SPC and DOE.

Contents: Injection Molding Technology. Extrusion Technology. Plastics and Plastics Properties Important in Injection Molding and Extrusion. Introduction to Statistical Process Control. Data Collection, Data Analysis, and Problem Solving Measurement. Control Charts. Process Capability and Special SPC Techniques for Molding and Extrusion. Other Tools to Improve Process Control.

T. Osswald, L. Turng, P. Gramann

Injection Molding Handbook2nd Edition


The injection molding industry has a new, up-to-date, com-prehensive handbook. Serving engineers, professionals, and others involved in this important industry sector, the handbook thoroughly covers every detail of the machine and the process. This all-encompassing resource also includes the topics directly affecting the injection molding process, such as materials, process control, simulation, design, and troubleshooting. The handbook presents a well-rounded overview of the underlying theory and physics that control the common injection molding process variation, without losing the practical hands-on presentation used throughout.

G. Pötsch, W. Michaeli

Injection MoldingAn Introduction 2nd Edition

ISBN 978-3-446-40635-3©2007, softcover, 79,90256 pages/275 figures/25 tables

This book provides an overview of the injection molding process and all its related aspects, such as material behavior, machine and mold design. Although the book is highly useful to advanced professionals, it is written in clear, simple language to enable beginners to understand the technology. In discussing the various operations related to the injection molding process, emphasis is placed on practical ways of processing and using plastics. The second edition is expanded to include all industrially relevant special injection molding techniques developed since the publication of the first edition.

Contents: Injection Molding Materials. Injection Molding Machine. Injection Mold. Process Control. Automation. Quality Assurance. Special Injection Molding Techniques.

Injection Molding


1717

J. Greener, R. Wimberger-Friedl

Precision Injection MoldingProcess, Materials, and Applications


One key aspect of the production of high precision components via injection molding technology is the need to meet extremely tight dimensional tolerances, often in the submicron range, and maintain these tolerances over the practical lifetimes of the molded articles. This book examines precision injection molding from different perspectives, covering materials, process, mold and machine aspects of the technology, with special emphasis on factors affecting the dimensional integrity and stability of the molded components. Special topics covered in this volume include: mechanisms of dimensional instability of molded plastics, models for prediction of warpage and shrinkage, crystallization phenomena in injection molding, process control, optical disc molding, micro-molding and microstructure replication for microfluidics.

H. Rees

Understanding Injection Molding TechnologyISBN 978-3-446-17728-4©1994, softcover, 39,90140 pages/76 figures

This introduction emphasizes the basic technical information specific to injection molding and the various technical problems faced when working in industry. The reader gains an understanding of machines, molds, injection molds, and the various molding techniques used in the past and today.

Contents: Introduction to Plastics Technology. Plastics Processing. Injection Molding. Other Mold Features and Terminology. Injection Molding Techniques. Automatic Product Handling.

J. Shoemaker

Moldflow Design GuideA Resource for Plastics Engineers


This book helps plastics designers and engineers solve common problems afflicting plastic parts and molds. Moldflow pioneered injection molding simulation in 1978 and has helped over 5,000 manufacturers make better parts faster and with higher profit. Whether you use Moldflow software or not, this guide is an indispensable tool to understanding plastic flow, CAE analysis and results, and cooling and warp effects to aid in the successful design and manufacture of parts and molds. Incorporating much of the knowledge developed at Moldflow, this book includes an overview of polymer flow behavior and the injection molding process, design principles to facilitate integrated part and mold design, and examples of how Moldflow technology can be used both to solve problems and optimize design and manufacturing.

Injection Molding


1818

W. Michaeli, H. Greif, G. Kretzschmar, F. Ehrig

Training in Injection Molding2nd Edition

ISBN 978-3-446-21418-7©2001, softcover, 49,90160 pages/100 figures

This text covers the entire field of injection molding - from materials, to processing, to the recycling of injection molded parts. Key questions at the beginning of each lesson help readers work with specific objectives in mind. Review questions allow them to test their knowledge.

Contents: Fundamentals. The Injection Molding Machine. The Plasticating and Injection Unit. The Mold. The Clamping Unit. Hydraulics. Controls. The Electrical System. The Injection Molding Process. Mold Design. Quality Assurance in Injection Molding. Recycling of Plastic Waste.

F. Johannaber

Injection Molding MachinesA User’s Guide 4th Edition


Since the publication of the 3rd edition of Injection Molding Machines, there has been considerable progress in certain process applications that make special demands on machinery and their control functions in particular. The book provides an elegant, succinct description of the injection molding process.

By concentrating on a few key parameters, such as pressure, temperature, their rates, and their influence on the properties of moldings, it provides a clear insight into this technology. The subsequent comprehensive presentation of technical data relating to individual machine components and performance is unique and will be especially appreciated by practitioners.

J. Beaumont

Runner and Gating Design HandbookTools for Successful Injection Molding 2nd Edition

ISBN 978-3-446-40765-7 ©2007, hardcover, 129,90324 pages/331 full-color figures/10 tables

For the first time, both the art and the science of designing runners and gates are presented in a concise format. Tried and true runner and gating design techniques successfully used with various materials and molding applications are described together with cutting-edge new technologies.

This handbook helps determine the optimum design, when to use what type of runner systems, and how to isolate molding problems generated from the gate and runner vs. other molding issues Full-color 3-D graphics, illustrations and photographs as well as charts, checklists, troubleshooting guides, and contributions from the industry’s leading expert John Bozzelli complete this handbook.

“... accomplishes its in-tended purpose of being an excellent [general] teaching aid.“

Injection Molding Magazine

Injection Molding


1919

P. Unger

Hot Runner TechnologyISBN 978-3-446-40584-4 ©2006, hardcover, 129,90249 pages/210 figures/25 tables

Quality and profitability of injection molding operations can be considerably influenced by the hot runner system. The many variations and design principles of hot runners are material-dependent and therefore not universally applicable. Knowing about and recognizing these limitations will make or break a molder’s success. This book provides a comprehensive overview of hot runner technology, advantageous design principles, and applications. It includes the necessary basics as well as many proven designs and application examples.

Contents: Heat Technology. Hot Runner Components. Heating Manifold Blocks. Heating of Hot Runner Nozzles. Temperature Measuring and Controlling. Material Behavior under Stress. Corrosion and Wear. Screw Connections and Material Selection. Basic Plastics Technology. Maintenance and Storage Molds. Design. Suppliers of Hot Runner Systems.

G. Menges, W. Michaeli, P. Mohren

How to Make Injection Molds3rd Edition


This classic covers all aspects of injection mold design and manufacturing including material selection, general mold design, fabricating cavities and cores, dimensioning for mechanical and thermal design, and venting.

Partial Contents: Mold Making Techniques. Mold Costs. Runner Systems. Gates. Venting of Molds. Heat Exchange. Shrinkage. Mechanical Design. Shifting of Cores. Ejection. Alignment. Computer Assisted Mold Design. Maintenance. Mold Standards. Correction of Molding Defects. Special Processes – Special Molds.

“... [The 2nd Edition is] an example of how books should be written ... [it] will be used by molders, mold designers and moldmakers and will become a standard.”

Polymer News

D. Kazmer

Injection Mold Design EngineeringISBN 978-3-446-41266-8©2007, hardcover, 99,90444 pages/280 figures/53 tables

This book provides a vision and structure to synergize all the engineering disciplines that converge in the mold design process. The topics are presented in a top-down manner, beginning with introductory definitions and the big picture before proceeding to layout and detailed design of molds. This book provides pragmatic analysis with worked examples that can be readily adapted to real-world mold design applications. It helps students and practitioners to understand the inner workings of injection molds and encourages thinking “outside the box” in developing innovative and highly functional mold designs.

Contents: Introduction. Plastic Part Design. Mold Cost Estimation. Mold Layout Design. Cavity Filling Analysis and Design. Feed System Design. Gating Design. Venting. Cooling System Design. Shrinkage and Warpage. Ejection System Design. Structural System Design. Mold Technologies.

Injection Molding


2020

P. Unger

Gastrow Injection Molds130 Proven Designs 4th Edition


Designing the perfect mold is probably the most challenging task in plastics processing, especially in injection molding. The mold determines the quality, performance, and the profitability of a plastic part. Neither modern computer technology nor sophisticated CAE software can substitute the experience of the practicing mold engineer. This is why the “Gastrow” is so special to plastics engineers: 130 mold designs are presented in this extensively revised edition of the great classic in mold making. Each of the case studies was actually built, tested, and run successfully in production. The book is written by practitioners, describing problem solving in the design and the manufacture of injection molds. The wealth of information includes rules of thumb, design details, and practical tips invaluable for everyone involved in this field.

H. Rees

Understanding Injection Mold DesignISBN 978-3-446-21587-0©2001, softcover, 39,90127 pages/36 figures

This book provides the reader with the ground rules for designing injection molds. It explains the basic mold principles regardless of what size and type of product is to be injection molded, whether the mold is small or large, has single or multiple cavities, and who designs or builds the mold.

Contents: Starting New in the Mold Design Field. The Basics of an Injection Molding Machine. Understanding the Basics of the Injection Mold. Before Starting to Design a Mold: Machine Specification, Mold Design, Preload, Mold Material Selection, Stack Molds, Mold Layout and Assembly Drawings. Review and Followup. Typical Examples. Estimating of Mold Costs. Machining, Mold Materials, and Heat Treatment.

H. Rees, B. Catoen

Selecting Injection MoldsWeighing Cost versus Productivity

ISBN 978-3-446-389-6©2006, hardcover, 99,90230 pages/140 full-color figures/25 tables

This book explains to the mold designer the importance of knowing the expected productivity of the mold and how this information affects the cost of the planned mold and the cost of the molded product. It suggests many approaches to reduce mold cost and also to improve productivity by often just simple design changes. Above all, it emphasizes again and again that the ultimate goal is not to procure the lowest cost but to produce the lowest cost product.

Contents: How to approach selection of the mold features. How productivity affects mold selection. How selection of design features affects mold cost. How to reduce mold and product cost by simple design changes. How to approach estimating mold cost.

Injection Molding


2121

C. Rauwendaal

Understanding Extrusion2nd Edition


No engineering degree required! This book presents basic information on extrusion technology. Written for operators, supervisors, technical service professionals, as well as newcomers to the industry and students, this book introduces the process, machinery, process control, materials, and trouble shooting tips. The extended second edition covers high-speed extrusion, how to reduce material cost, efficient extrusion, purging and product changeover, how to reduce energy consumption, and new developments in extruder screw design.

Contents: Extrusion Machinery. Instrumentation and Control and Extrusion Lines. Complete Extrusion Lines. Plastics and Properties Important in Extrusion. How an Extruder Works. How to Run an Extruder. How to Troubleshoot Extrusion Problems. New Developments.

M. Noriega, C. Rauwendaal

Troubleshooting the Extrusion ProcessA Systematic Approach to Solving Plastic Extrusion Problems 2nd Edition


Troubleshooting extrusion problems is one of the most challenging tasks for everyone involved in extrusion operations. It requires a good understanding of the extrusion process, knowledge of the material properties, good instrumentation, good analysis tools, and a systematic and logical approach. This book addresses all issues crucial in extrusion troubleshooting. In addition, industrial case studies, richly illustrated with photographs and photomicrographs, are used to provide exemplary approaches to efficient problem analysis and problem solving.

Partial Contents: Requirements for Efficient Troubleshooting. Tools for Troubleshooting. Systematic Troubleshooting. Case Studies: Film Coextrusion. Film Coextrusion with Interfacial Problems. Lines in the Extruded Film. Color Variation in Polypropylene Carpet Fiber. Plastic Film with Poor Transparency. Wear Problem in Film Extrusion. Multilayer Film. Dispersion Problem in a High-Density Polyethylene Bottle. Polymer Degradation. Heat-Sealing Problems in a Coextruded Film. Output Problem in a Blown Film Line. Master Batch Selection. Pipe Extrusion Problem. Gel Formation in a Coextruded Film. Agglomerates and Grammage Variation in a PP Sheet. Insufficient Melting and Mixing in a Plasticating Unit. High Melt Temperature and Insufficient Output in Coextrusion. Deficient Solids Conveying and Dispersion.

Extrusion


C. Rauwendaal

SPC in Injection Molding and Extrusion2nd Edition


Many SPC training programs are taught by people that are familiar with statistics but know little about process technology. Successful implementation of SPC requires an understanding of SPC as well as process know-how. This book teaches not only the principles of SPC but also basic injection molding and extrusion process technology. Lists of commercially available software for SPC and DOE are included.

Contents: Injection Molding Technology. Extrusion Technology. Plastics and Plastics Properties Important in Injection Molding and Extrusion. Introduction to Statistical Process Control. Data Collection, Data Analysis, and Problem Solving Measurement. Control Charts. Process Capability and Special SPC Techniques for Molding and Extrusion. Other Tools to Improve Process Control.

2222

J. White, E.K. Kim

Twin Screw ExtrusionTechnology and Principles 2nd Edition


This book distinguishes between the different types of twin screw extruders and clearly describes their capabilities. It examines the fundamentals, development, and technology of twin screw extruders widely used for compounding, blending, reactive extrusion, and devolatilization.

Contents: Overview of Multi-Screw Extruders. Background: Polymer Properties and Flow Principles. Single Screw Extrusion. Technology of Intermeshing Co-Rotating Twin Screw Extruders. Flow Mechanisms and Modeling of Intermeshing Co-Rotating Twin Screw. Extruders. Experimental Studies of Intermeshing Co-Rotating Twin Screw Extruders. Technology of Intermeshing Counter-Rotating Twin Screw Extruders. Flow Mechanisms and Modeling of Intermeshing Counter-Rotating Twin. Screw Extruders. Experimental Studies of Intermeshing Counter-

Rotating Twin Screw Extruders. Flow Mechanisms and Modeling of Non-Intermeshing Counter-Rotating. Twin Screw Extruders. Experimental Studies of Non-Intermeshing Counter-Rotating Twin Screw. Extruders. Technology of Continuous Mixers. Flow Mechanisms and Modeling in Continuous Mixers. Experimental Studies of Continuous Mixers. Kokneter. Reactive Extrusion. Devolatilization and Dewatering. Comparisons and Concluding Remarks.

Extrusion


2323

C. Rauwendaal

Polymer Extrusion4th Edition


This bestseller examines the main components of extruders used for processing thermoplastics, including drives, reducers, bearings, screws, dies, screens, heating and cooling systems, and instrumentation and control. Basic principles, polymer properties, applications, and analysis of processes are presented.

Partial Contents: Extrusion Machinery. Process Analysis. Fundamental Principles. Polymer Properties. Applications. Extruder Screw Design. Die Design. Twin Screw Extruders. Troubleshooting.

“Rauwendaal has succeeded once more in improving an already excellent work, and providing what will come to be regarded as a classic text by future generations.”

Polymer News

F. Hensen

Plastics Extrusion Technology2nd Edition


Now updated, this industry standard provides information on the aspects and processes of extrusion technology, including design, construction, and operation of extrusion lines. Well-known experts in various fields of extrusion have contributed to this book. As a reference book it will undoubtedly prove a considerable benefit to engineers involved with the extrusion process.

Partial Contents: Compounding Lines. Extrusion of Pipes, Profiles, and Cables. Blown Films. Blown Film Coextrusion. Flat Film Extrusion Using Chill-Roll Casting. Production of Films and Sheets by the Roll-Stack Process. Manufacture of Oriented Films. Film Tapes. Monofilament Extrusion. Extrusion Coating and Laminating.

J. White, H. Potente

Screw ExtrusionISBN 978-3-446-19624-7©2002, hardcover, 149,90464 pages/334 figures/35 tables

This book emphasizes the understanding of the underlying principles of screw extrusion and helps the engineer to optimize equipment and enhance production rates and properties of synthetic polymers. This goal depends on optimum screw design to provide homogeneous melts for successful post processing, such as fiber spinning, blown film, cast film, and sheets.

Contents: Fundamentals. Screw Extrusion Technology. Technology of Single Screw Extrusion with Reciprocating Screws. Single Screw Extruder Analysis and Design. Twin- and Multiscrew Extrusion.

Extrusion


Design

24

Processing & Manufacturing

24

C. Chung

Extrusion of PolymersTheory & Practice 2nd Edition


The author presents single-screw extrusion technology together with the relevant polymer fundamentals, with an emphasis on screw design. The presentation begins on a physical level, providing an in-depth conceptual understanding, followed by an analytical level with mathematical models. Practical applications of the mathematical models are illustrated by numerous examples. A brief description of twin_screw extrusion technology is also presented. The second edition includes new chapters on die design, elastic effects in melt flow, and a new type of single-screw extruder with channeled barrel as well as improvements and corrections of the first edition.

Partial Contents: Physical Description of Single-Screw Extrusion· Fundamentals of Polymers and Melt Rheology · Gear Pumps, Static Mixers, and Dynamic Mixers· Physical Description of Twin-Screw Extruders

K. Cantor

Blown Film ExtrusionAn Introduction 2nd edition

ISBN 978-3-446-41705-2©2011, hardcover, 89,90175 pages/107 figures/15 tablesIncludes CD

From hardware and materials through processing and properties, this book presents a broad coverage of blown film extrusion and ensures a useful balance of theory and practice. It explains certain effects in the blown film process so readers are better able to troubleshoot and improve their operations. Also, current practices and equipment are emphasized to keep readers up to date with the most productive and efficient technology.

Contents: Materials for Blown Film. Extrusion Overview. Hardware for Blown Film. Processing. Coextrusion. Film Properties. Troubleshooting.

Companion CD: The Blown Film Extrusion Simulator enhances the learning process by teaching blown film extrusion equipment operation and processing principles. The realistic graphic interface and intuitive operating techniques emulate processing methods so learners can move quickly from the simulator to real production equipment. Throughout this book, exercises using the simulator are described to complement the methods and principles explained. Readers are encouraged to take a break from the book and spend a few minutes with the simulator to enhance their understanding of the content.

Extrusion


Design

25

Processing & Manufacturing

25

K. Kohlgrüber

Co-Rotating Twin-Screw ExtrudersFundamentals, Technology, and Applications


Co-rotating screws are used in many branches of industry for producing, preparing and processing highly viscous materials. These machines usually have modular configurations and are thus quite flexible for adapting to changing tasks and material properties. Well-founded knowledge of machines, processes and material behavior are required in order to design twin-screw extruders for economically successful operations.

This book provides basic engineering knowledge regarding twin-screw machines; it lists the most important machine-technical requirements and provides examples based on actual practice. Better understanding of the processes is emphasized as this is a prerequisite for optimizing twin-screw designs and operating them efficiently.

H. Harris

Extrusion ControlMachine – Process – Product


In a very practical and down-to earth way the author explains how quality in extrusion can be measured, controlled, and improved. In particular, he conveys an understanding of how extruders should be controlled and what good, closed loop controls can accomplish. The author’s approach and style clearly conveys that he has been involved in this field for many years and that he knows from experience what kind of problems an extrusion operator faces and how to successfully tackle these problems.

This book is a helpful tool to improve and stabilize the extrusion process, thus facilitating a more profitable operation.

W. Michaeli

Extrusion Dies for Plastics and RubberDesign and Engineering Computations 3rd Edition


This well-received book provides a comprehensive account of the full range of dies used for the extrusion of plastics and rubber, and incorporates all new developments and innovations in the field of extrusion and die design. Advice on the configuration of dies is given, and the possibilities and limitations of computer-aided design are demonstrated.

This detailed, yet simplified approach provides daily support for plastics engineers while also offering a solid foundation for those training in this field.

Extrusion


2626

J. Throne

Thermoplastic Foam ExtrusionAn Introduction


Foams enjoy growing popularity because they have unique insulating properties, impact-resistant characteristics, buoyancy, and outstanding strength-to-weight ratios. This unique introduction covers both low- and high-density thermoplastic foams in an easy-to-follow style, avoiding excursions into the theoretical aspects of foam processing.

The book includes information on materials and their properties and all major foam extrusion processes. A considerable part of the volume is taken up by a comprehensive troubleshooting guide, designed to help newcomers as well as seasoned practitioners navigate the pitfalls of foam production.

G. Beall, J. Throne

Hollow Plastic PartsDesign and Manufacture


Hollow plastic parts range in size from small unit dose liquor bottles, doll heads and syringe bulbs to large gasoline tanks, pallets, and playground equipment. Designers and design engineers are often familiar with one way of making these parts but may not be aware of other methods that may offer greater design and performance flexibility.

The book provides comprehensive design and manufacturing comparisons of three major methods—blow molding, rotational molding and twin-sheet thermoforming—as well as an overview of other methods used to produce hollow plastic parts.

Not only will the seasoned designer be able to determine the advantages and limitations of specific technologies, but also the newcomer will be able to quickly select the best manufacturing method for any particular hollow product.

N. Lee

Blow Molding Design Guide2nd Edition


The second edition of this widely accepted book provides a general understanding of the blow molding process. It offers a practical, hands-on approach, concentrating on real life, day-to-day problems faced by those working to create cost-effective blow molded parts. The author uses an integrated approach to plastic part design, considering material properties, process benefits and limitations, mold engineering, decoration, finishing, and assembly techniques, while always keeping a focus on manufacturability issues.

Contents: Overview. Blow Mold Process/Extrusion Blow Molding. Materials. Molds/Basic. Construction. Basic Design Considerations. Design of Bottles. Industrial and Large Parts. Other Products. CAD in Blow Mold Part Design. Finishing and Decoration of Blow Molded Products. Fastening and Joining. Economics of Blow Molding.

Blow Molding


2727

N. Lee

Understanding Blow Molding2nd Edition

ISBN 978-3-446-41265-1 ©2007, softcover, 69,90194 pages/218 figures/15 tables

Understanding Blow Molding focuses on hands-on, practical applications, which will benefit those new to the plastic blow molding industry, as well as those who are experienced but may not have been exposed to all facets of a blow molding plant. People from various disciplines such as product and manufacturing engineering, marketing, design, research and development, as well as operation personnel, will also gain insight into solving the everyday problems of a blow molding operation.

This revised second edition is expanded by a comprehensive troubleshooting guide that proves particularly helpful to any practitioner.

D. Rosato, A. Rosato, D. DiMattia

Blow Molding Handbook2nd Edition


An industry standard, this book provides insight to critical areas such as product design, meeting performance requirements, reducing cost, and zero defect targets. The information presented is of value to fabricators, designers, and engineers and it also provides a firm basis for the beginner. The intent is to provide a complete review of the important aspect of the blow molding process that goes from the practical to the theoretical and from the elementary to the advanced.

Partial Contents: Plasticator Melting Operation. Extrusion BM. Injection BM. Stretch BM. Tooling. Plastic Types and Processability. Fundamentals of Product Design. Process Control. Computer Operation. Process Selection and Auxiliary Equipment and Secondary Operations. Troubleshooting and Maintenance.

Blow Molding


2828

J. Throne

Thermoplastic Foam ExtrusionAn Introduction

ISBN 978-3-446-22848-1 ©2004, hardcover, 69,90150 pages/57 figures/30 tables Foams enjoy growing popularity because they have unique insulating properties, impact-resistant characteristics, buoyancy, and outstanding strength-to-weight ratios. This unique introduction covers both low- and high-density thermoplastic foams in an easy-to-follow style, avoiding excursions into the theoretical aspects of foam processing.

The book includes information on materials and their properties and all major foam extrusion processes. A considerable part of the volume is taken up by a comprehensive troubleshooting guide, designed to help newcomers as well as seasoned practitioners navigate the pitfalls of foam production.

J. Throne

Understanding Thermoforming2nd Edition

ISBN 978-3-446-40796-0©2008, flexcover, 69,90280 pages/110 figures/26 tables

Modern thermoforming practice is a balance of practical experience and the application of engineering principles. This very practical book introduces the process, its tools and machinery, and the commonly used materials to novices and practicing engineers alike.

Contents: General Forming Concepts. Part Design Machinery for the Thick-Gauge Forming Process. Machinery for the Light-Gauge Forming Process. Machines for Other Applications Molds and Mold Design. Methods of Heating Sheet. Sheet Stretching and Cooling. Trimming. Polymers and Plastics Quality Control. Comparison with Other Technologies. Pragmatic Aspects of Thermoforming.

A. Illig

ThermoformingA Practical Guide


This book provides comprehensive information on thermoforming principles and processes. It introduces students, as well as engineers and technicians with experience in this field, to this area of plastics manufacturing.

The reader will find extensive information on thermoforming- related subjects, from materials’ properties and processing data, to machines, tools, and trouble shooting.

Contents: Thermoplastics. Basic Principles and Terms Applied in Thermoforming. Thermoforming Procedures. Heating of Thermoplastics Forming Materials. Heatbalancing of Thermoforming Tools. Demolding. Finishing of Thermoformed Articles. Possible Pitfalls with Thermoforming. Thermoforming Tools.

Thermoforming


www.hanserpublications.com 29

J. Throne

Technology of ThermoformingISBN 978-3-446-17812-0©1996, hardcover, 199,90898 pages/528 figures/180 tables

This thorough text covers the thermoforming process and products. It moves from a relatively simple approach to more technical in-depth information, featuring examples and guidelines to illustrate all technical aspects.

Contents: Thermoforming: Definitions, History, Methods, and Equipment. Polymeric Materials. Heating the Sheet. Stretching the Sheet. Cooling and Trimming the Part. Molds. Parts Design. Producing Sheet and Film. Latest Technologies. Set-Up Protocols, Trouble-Shooting, and the Economics of Thermoforming.

“...balances practical hints with the application of en-gineering and computational principles.”

Sci-Tech News

Thermoforming


3030

A. Pocius

Adhesion and Adhesives TechnologyAn Introduction 2nd Edition


The emphasis of this book is on understanding the science of adhesion. Each section or chapter starts with a simple view of the subject area and then builds to a point at which more detail is available for the reader who is or wants to be a practitioner of the art and science of adhesion.

Partial Contents: Mechanical Properties. Mechanical Tests of Adhesive Bond Performance. Basics of Intermolecular Forces and Surface Science. Basic Physical/Chemical Properties of Polymers. Relationship of Surface Science and Adhesion Science. Surface Preparation of Adherends for Adhesive Bonding. Chemistry and Physical Properties of Structural Adhesives.

“Very highly recommended“Adhesives & Sealants

Newsletter

R. Wolf

Plastic Surface ModificationSurface Treatment, Decoration, and Adhesion

ISBN 978-3-446-41270-5 ©2010, hardcover, 99,90250 pages

Polymer surface modification is a topic that has been the object of a large number of investigations by academia and industry, but relatively little attention has been paid to surface activation technologies which, when appropriately utilized, make specific polymer-based surfaces receptive to value-adding interfaces such as inks, coatings, and adhesive formulations. Adhesion strength is generally determined by the properties of a base material and its interface. Optimizing adhesion strength can be accomplished by modifying these interfaces chemically and physically. As polymers are continually engineered to meet new product application requirements, optimizing the activation of these surfaces requires a fresh look at cost effective ways to etch, clean and functionalize them.

F. Wolff-Fabris, V. Altstädt, U. Arnold, M. Döring

Electron Beam Curing of CompositesISBN 978-3-446-42405-9©2010, hardcover, 89,90136 pages/83 figures/13 tables

Electron beam curing technology for advanced composites has emerged as a credible and attractive alternative to thermal curing for most composite products. Technical advantages, such as aerospace structures, include curing at room temperature, using low-cost tooling, and the ability to fabricate large integrated structure including structures too large to fit inside autoclaves. Studies by aerospace companies have shown potential cost savings of 10-60 % by using electron beam curing.

In this book, both theoretical and practical aspects of electron beam curing of composites are presented, intending to build a bridge between the academic knowledge and the industrial applications.

Other Processes


3131

D. Grewell, A. Benatar, J. Park

Plastics and Composites Welding HandbookISBN 978-3-446-19534-9 ©2003, hardcover, 99,90423 pages/311 figures/15 tables

This comprehensive handbook covers all commercially available welding processes. It helps the reader select the best suited process for his/her application and provides an understanding of each process by presenting the limitations and benefits. The focus on practical aspects such as weldability, optimizing part design, troubleshooting, and testing makes this book an indispensable tool for everyone involved in welding of plastics. At the same time it also conveys the basic theoretical principles of plastic welding, such as squeeze flow, molecular diffusion, and heat transfer mechanisms.

W. Baker, C. Scott, G. Hu

Reactive Polymer BlendingISBN 978-3-446-21068-4©2001, hardcover, 129,90400 pages/150 figures/27 tables

This book provides a com-prehensive overview of the general principles involved in successful reactive blending. Pioneering work on several key issues including copolymer formation, interface development, and morphology are covered.

Contents: Reactive Blending with Immiscible Functional Polymers. Key Role of Structural Features of Compatibilizing Additives in Reactive Blending. Morphological and Rheological Aspects of Reactive Polymer Blending. Reactive Blending in Screw Extruders. Extrusion Equipment for Reactive Blending. Rubber Toughening of Polyamides by Reactive Blending. Compatibilization Using Low Molecular Weight Reactive Additives.

B. Davis, P. Gramann, T. Osswald, A. Rios

Compression MoldingISBN 978-3-446-22166-6 ©2003, hardcover, 79,90208 pages/150 full-color figures/25 tables

This book not only covers the advantages and disadvantages of molding operations with SMC/BMC (thermosetting) and GMT/LFT (thermoplastic) materials but also provides the reader with relatively simple models for monitoring, troubleshooting, and quality control of their process. Also covered is the important role of fiber reinforcement — how the quantity, length and fiber orientation influence part strength and stiffness.

Contents: Materials. Process Overview. Mold Filling. Solidification. Mechanical Properties.

Other Processes


32

R. Davé, A. Loos

Processing of CompositesISBN 978-3-446-18044-4©2000, hardcover, 179,90504 pages/238 figures/33 tables

Composites are said to be the “Materials of the Future.” Advanced polymer composites are beginning to be used in down-to-earth structures such as bridges, buildings, and highways. The objectives of this book are to provide an overview of the fundamental principles underlying composite processing and to summarize the most important processes for composite manufacturing.

Partial Contents: Chemistry, Kinetics, and Rheology of Thermoplastic Resins. Thermoset Resin Cure Kinetics and Rheology. Phase Separation and Morphology of Toughened Thermosets. Frequency Dependent Dielectric Sensing of Cure. Modeling. Transport of Heat, Mass, and Momentum in Processing. Void Growth and Dissolution.

K. Okamoto

Microcellular ProcessingISBN 978-3-446-22344-8©2003, hardcover, 89,90199 pages/144 figures/15 tables

A growing number of plastic processors gain a competitive edge by utilizing the commercial microcellular process with their existing injection molding or extrusion equipment with only low-cost modifications. End users also gain an advantage when the microcellular process is incorporated into product design and cost.

To facilitate the transition and to help processors and end users make the most of this cutting-edge commercial technology, this book provides a comprehensive description of all crucial elements.

Partial Contents: Theoretical Basis. MuCell Injection Molding. Equipment and Processing Basics. MuCell Flow Simulation Criteria for Mold and Part Design. MuCell Extrusion. Case Studies.

I. Ward, P. Coates, M. Dumoulin

Solid Phase Processing of PolymersISBN 978-3-446-19622-3©2000, hardcover, 129,90427 pages/252 figures

This book provides a comprehensive, up-to-date account of the solid phase processing of polymers with particular emphasis on the production of oriented polymers in the form of fibers, films, and solid sections - including rods, sheets, and tubes. Various processing methods, such as tensile drawing, die drawing, ram extrusion, and hydrostatic extrusion are covered.

Contents: Deformation Mechanisms and Morphology of Crystalline Polymers. Characterization of Orientation. Solid State Processing of Fibers. High Modulus Fibers. Development of Molecular Orientation During Biaxial Film Tentering of PET. Rolling and Roll-Drawing of Semi-Crystalline Thermoplastics. Planar Deformation of Thermoplastics. Solid State Extrusion and Die Drawing. Mathematical Modeling.

Other Processes


3333

G. Beall

Rotational MoldingDesign, Materials, Tooling, and Processing


A highly versatile process, rotational molding allows for incredible design flexibility with the added benefit of low production costs. One of its advantages over other plastics processes is that one can mold more complex shapes with uniform wall thickness. The emphasis of this book is on product design while providing an introduction to the process. It also helps readers understand and apply the manufacturing techniques involved in rotational molding.

Contents: The Rotational Molding Industry. Rotational Molding Materials. Design Considerations. Rotational Molding Molds. Understanding the Process. Costing Considerations. When to Choose Rotational Molding.

R. Parnas

Liquid Composite MoldingISBN 978-3-446-21394-4©2000, hardcover, 89,90270 pages/82 figuresIncludes CD

Liquid Composite Molding provides a fundamental understanding of transport phenomena in porous media, textile and automation technology to construct the porous reinforcement, and computer-aided engineering for design optimization. This well integrated text offers industrial practitioners an expertly organized guide to the engineering principles and manufacturing issues critical to successful molding operations. Problems at the end of each chapter expand and clarify the most important topics.

Contents: Introduction. Fundamentals – Transport Phenomena. RTM Fundamentals – Reinforcement Construction. Manufacturing Composites. The Microstructure.

CD Content: A permeability database and a flow simulator for process design.

Other Processes

MATERIALS

Design

34

Materials

34

C. Wilkes, J. Summers, C. Daniels

PVC HandbookISBN 978-3-446-22714-9 ©2005, hardcover, 199,90749 pages/239 figures/35 tables

This comprehensive handbook provides a complete account of all aspects of PVC – from monomer manufacture to polymerization; the gamut of such additives as stabilizers, lubricants, plasticizers, impact modifiers, fillers and reinforcing agents; blends and alloys; compounding and processing; characterization; combustion resistance and weatherability; product engineering design; applications; environmental and safety; and finally the PVC industry dynamics.

The handbook contains both practical formulation information as well as a mechanistic view of why PVC behaves as it does.

N. Pasquini

Polypropylene Handbook2nd Edition


Following the successful approach of the first edition, this book presents the current state of the PP industry. At its core is a detailed description of the polymerization, the catalysts, and the breakthroughs that occurred during the last two decades. Comprehensively covered are morphology, characterization, stabilization, properties, manufacturing, worldwide demand, environmental considerations, applications, and regulatory considerations.

However, this update covers more than products, technology, and market, which undoubtedly are the most important dimensions of the PP industry.

H.J. Endres, A. Siebert-Raths

Engineering BiopolymersMarkets, Manufacturing, Properties, and Applications

ISBN 978-3-446-42403-6 ©2011, hardcover, 299,00 648 pages

This book focuses on the hot topic of bio/renewable materials. It is based on comprehensive research projects, during which these materials were systematically analyzed and characterized. It offers comparable data not only for biogenic polymers and biological macromolecules such as proteins but also for engineering materials.

This book also includes valuable information regarding micro-structure, manufacturing, and processing, application, and recycling properties of biopolymers.

General Overview

MATERIALS

Design

35

Materials

35

E. Campo

Industrial PolymersISBN 978-3-446-41119-4 ©2007, hardcover, 99,90 192 pages/280 full-color figures

This book provides a comprehensive and very practical overview of the various plastic materials used in today’s industrial applications. It focuses on material properties and areas of application.

All industrially significant plastic families and grades are introduced following the same approach: their chemical constitution, manufacturing, properties, processing, and end-use applications. This consistent presentation allows easy comparison of different materials and helps with the initial identification of suitable plastic materials for a given end use. Ample full-color illustrations are testimony to the fact that plastic materials are the ultimate tribute to man’s creativity and inventiveness.

Contents: Polymeric Materials. Thermoplastic Polymers. Thermoplastic Elastomers (TPE). Liquid Injection Molding Silicone (LIM). Thermoset Polymers.

G. Ehrenstein

Polymeric MaterialsStructure, Properties, Applications

ISBN 978-3-446-21461-3 ©2001, softcover, 49,90278 pages/215 figures/20 tables

Focuses on the relationships between the chemical structure and the related physical characteristics of plastics, which determine appropriate material selection, design, and processing of plastic parts. One of the special features is the extensive discussion and explanation of the interdependence between structure-properties and processing. The book contains numerous application-oriented examples and is presented at an intermediate level for both practicing plastic engineers and advanced engineering students.

Contents: Economic Development – Market Review and Predictions. General Characteristics of Polymeric Materials. Molecular Structure and Synthesis of Polymers. Structure of Polymeric Materials. Thermomechanical Properties. Mechanical Behavior. Aging and Stabilization. Overview of Selected Polymeric Materials.

J. White, D. Choi

PolyolefinsProcessing, Structure Development, and Properties


Polyolefins, the polymers synthesized from olefinic monomers, are the major commercial thermoplastics. They are also important elastomers and the components of major thermoplastic elastomers. Polyethylene and polypropylene in volume are the two largest thermoplastics and are fabricated into filaments, films, and moldings.

For the first time, the reader will find a comprehensive description of the structuring of molten polyolefins in fiber, film and molding processes with correlation between structural order such as crystalline unit cell, polymorphic effect and orientation, and processing parameters.

General Overview

MATERIALS

3636

L. Robeson

Polymer BlendsA Comprehensive Review


Polymer blends offer a key option in solving emerging application requirements. The ability to combine existing polymers into new compositions with commercializable properties offers the advantage of reduced research and development expense compared to the development of new monomers and polymers to yield a similar property profile. An additional advantage is the much lower capital expense involved with scale-up and commercialization. Another specific advantage of polymer blends versus new monomer/polymer compositions is that blends often offer property profile combinations not easily obtained with new polymeric structures. In the rapidly emerging technology landscape, polymer blend technology can quickly respond to developing needs.

D. Klempner, V. Sendijarevic

Handbook of Polymeric Foams and Foam Technology2nd Edition


This handbook is designed to support engineers in their efforts to develop practical solutions for industrial design and manufacturing challenges. It describes all classes of polymeric foams, including their chemistry, synthesis, commercial production methods, properties, and applications.

Since the previous edition of this book, many of the industry’s most pressing problems—such as environmentally acceptable blowing agents, combustibility, and solid waste disposal—have been addressed and significant progress has been made. This edition reflects these developments as well as several new classes of foams brought to industrial application in recent years.

S. Fakirov, D. Bhattacharyya

Handbook of Engineering BiopolymersHomopolymers, Blends, and Composites


This volume presents the results of numerous worldwide studies focusing on the implementation of natural polymers as engineering plastics and the use of their inherent properties. It discusses the processing and, more extensively, the application of natural materials (cellulose and protein-based) as reinforcements for polymer composites. The structural, morphological, and thermal characteristics, as well as the mechanical behavior of the obtained materials are covered comprehensively.

In addition, the book includes case studies of commercial relevance. All natural polymers used in the blending or reinforcement of synthetic polymers are discussed in an attempt to cover the isolation, pretreatment, blending, and manufacturing of the respective materials.

General Overview

MATERIALS

T. Osswald, G. Menges

Materials Science of Polymers for Engineers2nd Edition

ISBN 987-156990-22464-3©2003, hardcover, 79,90630 pages/600 figures/25 tables

This introduction to polymer materials science is divided into three major sections: Basic Principles, Influence of Processing on Properties, and Engineering Design Properties. The first edition of this textbook was praised for its vast number of graphs and data that can be used as reference. The new second edition further strengthens this attribute with a new appendix containing material property graphs for the commonly used polymers. However, the most important change implemented in this edition is the introduction of real-world examples and a variety of problems at the end of each chapter.

J. White, K. Kim

Thermoplastic and Rubber CompoundsTechnology and Physical Chemistry


This book describes the composition of all major types of polymer compounds, both thermoplastics as well as rubbers. It describes the intended effects of various additives and the complexity of their, sometimes unintended, interactions.

Contents: Polymer-Particle Filler Systems. Polymer Solutions and Swollen Vulcanizates. Polymer Additive Binary Systems. Binary Polymer Blends. Ternary Systems: Polymer Blends Plus Solvent Additives and Compatibilizing Agents. Polymer-Filler-Additive Compounds. Multicomponent Compounds. Mixing Machinery.

3737

T. Osswald, E. Baur, S. Brinkmann, K. Oberbach, E. Schmachtenberg

International Plastics HandbookThe Resource for Plastics Engineers 4th Edition

ISBN 978-3-446-22905-1 ©2006, hardcover, 99,90920 pages/450 figures/177 tablesIncludes eBook

This comprehensive handbook provides everything there is to know about plastics. From material properties to machines, processing, and applications, the reader will find detailed information for the successful implementation of new materials and technologies. This concise, modern reference not only explains the basic facts and interrelationships about plastics but also offers a practical guide for engineers to succeed in today’s challenging global industrial world.

eBook Bonus: Included free with the purchase of this book is an online access code for the electronic version.

General Overview

MATERIALS

38

K. Uhlig

Discovering PolyurethanesISBN 978-3-446-21022-6 ©1999, hardcover, 59,90184 pages/124 figures/33 tables This book is a concise, yet easy-to-understand introduction into the wide field of polyurethanes. It provides an unusual, non-technical insight into polyurethanes. Information on the history and the development of polyurethanes, their market and economic opportunities are shared with the non-scientist. Raw materials, forms and properties of polyurethanes, their chemistry and industrial production –all this described on an introductory level avoiding chemical jargon and formulas.

Contents: The Polyurethane Age. The PU Market and Resources. Classifications of Types. Why Polyurethanes? List of Properties. How Is Polyurethane Produced? The Chemistry Must Be Right! The Quality Must Be Right. Waste and Recycling. Polyurethane Know-How. Prospects.

S. Bhattacharya, M. Kamal, R. Gupta

Polymeric NanocompositesTheory and Practice


This comprehensive reference book incorporates the latest developments in the synthesis, production, characterization, and application of various types of polymeric nanocomposites. It outlines the various preparation techniques using different types of nanoparticles and polymer matrices with emphasis on clay nanoparticles.

All fundamental issues such as thermodynamics, kinetics, and rheology are discussed. Also, the structure and the characterization of polymeric nanocomposites, including their molecular characteristics, thermal properties, morphology, and mechanical properties, are covered in detail.

L. Bottenbruch

Engineering ThermoplasticsPolycarbonates, Polyacetals, Polyesters, Cellulose Esters


This handbook covers the basic and technical aspects of chemistry, production, testing, properties, processing, and applications of polycarbonates, polyacetals, polyesters, and cellulose esters. For each of the four material categories the following topics are discussed: Chemical Structure, Preparation, Modification, Blends, Analysis, Properties, Processing, Post-Processing, Applications, Health and Environmental Aspects.

General Overview

MATERIALS

39

J. Bauman

Fatigue, Stress, and Strain of Rubber ComponentsA Guide for Design Engineers


This book covers the fatigue testing of specimens, curve fitting of equations to the test data, and the use of such equations in life prediction. Earlier chapters are background in the nature of rubber, history of its usage, brief mention of types of rubber and manufacturing methods. Stress-strain testing and behavior is covered to the extent relevant to fatigue analysis. Also, the text covers the application of finite element analysis to components to determine high stress points which are vulnerable to fatigue failure.

It is a very useful reference for practicing engineers charged with the responsibility to design structural rubber components where fatigue life is a concern. It also serves as a text for short courses, or as a supplementary text for a university course in rubber engineering.

J. Sommer

Engineered Rubber ProductsIntroduction to Design, Manufacture, and Testing


The successful manufacture of engineered rubber products is complicated. It involves different disciplines, materials, and types and designs of equipment. Problems sometimes occur because of less-than-desirable communication among personnel involved in the development and manufacture of rubber products. This book’s intent is to improve communication among different disciplines. Using a systems approach, it is further intended to introduce chemists and engineers to the unique capabilities of rubber in a wide range of tire and non-tire products. This book, which incorporates extensive bibliographies in most of its sections, can be read by individual section of interest or in its entirety.

J. Dick

Rubber TechnologyCompounding and Testing for Performance 2nd Edition


This book is a practical guide to cost-effective formulating of rubber compounds to achieve optimal processing and performance. It provides a thorough discussion of the principles of rubber compounding, rubber testing, and how various compound changes affect different properties and test measurements.

Partial Contents: Rubber Compounding. Compound Processing Characteristics and Testing. Vulcanizate Physical Properties, Performance Characteristics, and Testing. Rubber Compound Economics. The Technical Project Approach to Experimental Design and Compound Development. Elastomer Selection. General Purpose Elastomers and Blends. Specialty Elastomers. Polyurethane Elastomers. Thermoplastic Elastomers. Recycled Rubber.

General Overview

MATERIALS

40

G. Holden, H. Kricheldorf, R. Quirk

Thermoplastic Elastomers3rd Edition


Thermoplastic elastomers are one of the fastest growing material groups. They can be processed like thermoplastics but their properties are close to those of vulcanized elastomers. New products, processing techniques, properties, and applications have been developed recently. This is a unique, comprehensive, up-to-date guide to all scientific and technical aspects of thermoplastic elastomers — indispensable for everyone working in this field.

Partial Contents: Thermoplastic Polyurethane Elastomers. Styrenic Thermoplastic Elastomers. Anionic Triblock Copolymers. Polyolefin-Based Thermoplastic Elastomers. TPES Based on Halogen- Containing Polyolefins. TPES Based on Dynamically Vulcanized Elastomer-Thermoplastic Blends. Polyether Ester Elastomers. TPE’s Based on Polyamides.

J. Dick

How to Improve Rubber Compounds1500 Experimental Ideas for Problem Solving


Rubber compounding is a very complex endeavor. There are many interactions and many ways to achieve the target properties and economic goals while maintaining an acceptable tradeoff for these characteristics.

This book provides the reader with various experimental ideas that may guide them to developing better compounds and solving technical problems. In a combined effort, 20 renowned industrial experts compiled a large number of diverse experimental suggestions for enhancing a specific compound property. By reviewing the suggestions in this book, the compounder may develop a better feel for how to best achieve a compromise or trade-off with compound properties when developing new or improving tested rubber recipes.

G. Holden

Understanding Thermoplastic ElastomersISBN 978-3-446-19332-1©2000, softcover, 39,90117 pages

The object of this book is to provide a short introduction and overview of this rapidly changing field.

Contents: Introduction. Classification and Structure. Styrenic Block Copolymers. Multi-Block Copolymers. Hard Polymer/Elastomer Combinations. Applications. Economic Aspects and Tradenames. References.

“There is certainly no one who is better positioned to write this book than Geoff Holden since he has been part of the field since its inception. In fact, he is one of its most preeminent pioneers.“

Donald R. Paul, University of Texas, Austin

Rubber

MATERIALS

41

J. White, K. Kim

Thermoplastic and Rubber CompoundsTechnology and Physical Chemistry


This book describes the composition of all major types of polymer compounds, both thermoplastics as well as rubbers. It describes the intended effects of various additives and the complexity of their, sometimes unintended, interactions.

Contents: Polymer-Particle Filler Systems. Polymer Solutions and Swollen Vulcanizates. Polymer Additive Binary Systems. Binary Polymer Blends. Ternary Systems: Polymer Blends Plus Solvent Additives and Compatibilizing Agents. Polymer-Filler-Additive Compounds. Multicomponent Compounds. Mixing Machinery.

A. Gent

Engineering with RubberHow to Design Rubber Components 2nd Edition


This edition contains updated and revised material and many new problems that deal with specific issues and allow the reader to test their understanding of the materials.

This book deals with some basic principles on which successful use of rubber depends, including how an elastomer is chosen and a formulation developed; why rubber is highly elastic and relatively strong; and how one can estimate the stiffness, strength, and durability of rubber products.

Contents: Materials and Compounds. Elasticity. Dynamic Mechanical Properties. Strength. Mechanical Fatigue. Durability. Design of Components. Finite Element Analysis. Tests and Specifications.

P. Johnson

Rubber ProcessingAn Introduction


This book deals with all aspects of rubber processing; mixing, milling, calendering, extrusion and molding, and also testing and specification of raw materials, mixed compound, and end products. It also covers the importance of flow behavior (rheology) in rubber processing. It deals with basic theory and its application to practice.

Contents: Overview of Rubber Processing. Raw Materials Acceptance and Specifications. Mixing. Flow Behavior. Testing of Compounds. Curing Process. Calendering. Extrusion. Molding. Finished Product Testing.

Rubber

MATERIALS

42

W. Kleemann, K. Weber

Elastomer ProcessingFormulas and Tables

ISBN 978-3-446-21017-2©1998, softcover, 59,90214 pages/22 figures

The goal of this book is to provide a fundamental tool for chemists working in the field of compounding, using calculation functions, evaluation methods, and tables of material characteristics.

The equations and calculation methods set out in this book, together with the various product tables, can be used to calculate influences on the property profile of compound systems from the functional relationships presented.

Partial Contents: Compounds. Vulcanizates. Polymers. Carbon Black. Plasticizers. Rubber/Carbon Black/ Plasticizer Systems. Cure. Rubber to Metal Bonding. Aging. Characterizing Properties of Raw Materials and Additives.

J. White

Rubber ProcessingTechnology – Materials – Principles


This book covers the development of the technology and presents the theoretical and experimental aspects of rubber processing and engineering, including flow simulator.

Contents: Overview and Rubber Materials. Flow Characteristics. Internal Mixers and Mixing. Continuous Mixers. Extrusion: Screw Pumps. Extrusion: Dies and Post Die Equipment. Calendering. Molding.

“Designed to provide a pri-mary source of reference for veteran and novice alike ... a significant and much-needed addition.”

European Plastics News

D. Stoye, W. Freitag

Resins for CoatingsChemistry, Properties and Applications


Designed as a guide for the coating formulator and technologist as well as a reference for students, this handbook offers practical information, data, and references needed to understand and solve coating problems.

Contents: Basic Reactions, Branching, Crosslinking, and Gelling. Basic Properties. Processing States. Principles of Application. Polycondensates. Polyadducts. Addition Polymers. Other Coating Resins. Polymeric Coating Additives. Resin Analysis.

“... the best single source on the composition, manu-facture, analysis and use of resins for coatings ... it will become an industry standard.“

Rubber Chemistry & Technology

Rubber/Coatings

MATERIALS

Materials

43

D. Salem

Structure Formation in Polymeric FibersISBN 978-3-446-18203-5©2001, hardcover, 149,90580 pages/282 figures

The reader will find a comprehensive and critical review of the science of fiber formation, with special emphasis on the evolution of microstructure and its relationship to process conditions and molecular properties.

Contents: Structure Formation. Control of Spinline Dynamics for Enhanced Properties. Draw-Induced Structure Development in Flexible-Chain Polymers. Solution (Gel-Spinning and Ultra-Drawing of Ultra-High Molecular Weight Polyethylene. Electrospinning and the Formation of Nanofibers. Fibers from Liquid Crystalline Polymers. Solvent Spun Cellulose Fibers. Carbon Fibers. Fibers from Electrically Conductive Polymers. Fibers from Polymer Blends and Copolymers. Microstructure Characterization.

F. Fourné

Synthetic FibersMachines and Equipment Manufacture, Properties

ISBN 978-3-446-16072-9©1999, hardcover, 299,-904 pages/905 figures/185 tables

This comprehensive handbook covers the design of machines and equipment for the production of synthetic fibers - from raw materials to the final product.

Written by one of the pioneers in the field, this book covers materials, specific processes, the corresponding installations, machines, process data, and designs and calculations for different materials and varying function parameters.

Partial Contents: Introduction. Polymer Specific Processes. Theoretical and Experimental Principles. Plants, Equipment and Machines for the Production of Synthetic Yarns and Fibers. Special Processes and Plants. Auxiliary Plants and Equipment. Auxiliary Devices, Calculations, and Constructions.

R. Ryntz

Plastics and CoatingsDurability – Stabilization – Testing


This book is a comprehensive overview of the durability of coatings and plastics, such as their chemical, photooxidation, moisture, heat, and solvent resistance. The scope ranges from predicting the service life performance of coatings and plastics to actual quantification of mechanical and physical manifestations of degradation. Stabilization mechanisms, such as the role of pigments and light stabilizers, are discussed as well as the influence of processing conditions on residual stress and adhesion. Those who properly utilize plastics, from concept design through end-of-life recycling, will gain a competitive advantage in the global marketplace.

“...a good value, and I recommend it to everyone in the plastics and protective coatings business.”

D. Wiles in Polymer News

Fibers & Films

MATERIALS

Materials

44

H. Zweifel, R. D. Maier, M. Schiller

Plastics Additives Handbook6th Edition

ISBN 978-3-446-40801-2©2009 , hardcover, 199,901248 pages/300 figures/480 tablesIncludes eBook

Plastics without additives are not viable. Additives are essential to make plastics processable and to assure their end-use properties.

The demands on additives have continued to evolve, not only because of changes in processing conditions and production techniques but also because plastics are being used in more demanding applications.

This revised and updated edition, described earlier by one reviewer as the “bible” for anyone involved in the chemistry and technology of plastics additives, again provides an excellent overview of the complex science and technology of plastics additives and their industry. It offers guidance for all professionals involved in the development of new thermoplastic resin grades and novel end-use applications.

E. Weil, S. Levchik

Flame Retardants for Plastics and TextilesPractical Applications

ISBN 978-3-446-41652-9©2009, hardcover, 99,90304 pages

This book gives an overview of flame retardants, which are either in commercial use or in advanced stage of market development, reviewed polymer-by-polymer, supplemented by a brief overview of mode of action and interaction. It is more of a how-to book rather than an academic study. As such, it names trademarked materials as well as products that are in an active stage of development, gives suggestions for selecting among alternatives, provides suggested formulations, and offesr a starting point for the compounder or plastics fabricator to pass commercial flammability requirements.

Contents: Introduction to Flame Retardants. Overview of Mode of Action and Interaction. Polyolefins. Styrenics. PVC. Polyamides. Engineering thermoplastics. Unsaturated polyesters and Vinyl Esters.

J. Troitzsch

Plastics Flammability HandbookPrinciples – Regulations – Testing and Approval 3rd Edition


The completely revised and updated 3rd edition of this handbook covers all aspects of plastics flammability from fundamentals to the detailed description of national and international regulations, standards, test methods, and the approval procedures for plastics and plastic components in various fields of application. This unique and comprehensive handbook is a mandatory and essential reference for everyone concerned with plastics flammability.

“This book is particularly welcome in simplifying the difficult and often confusing area of national regulations and fire test procedures.”

Plastics and Rubber International

Additives/Colors

MATERIALS

45

A. Müller

Coloring of PlasticsFundamentals – Colorants – Preparations


This book describes the various aspects of coloring plastics, such as the construction of the processing machine, the processing technology, quality assurance of the raw materials and final products, toxicology of the raw materials, and the legal aspects from the handling of all ingredients during the production of a color preparation to the processing of plastic parts. It also includes the safe use of the plastic products in their specific application.

Partial Contents: Methods Used to Color Plastics. Requirements for Color Preparations. Composition of Color Preparations. Colorants for Polymers. Additives for Polymers. Processing Errors and Their Elimination. Quality Assurance. Mold Construction. Legislation. List of Colorants.

J. Brandrup, M. Bittner, G. Menges, W. Michaeli

Recycling and Recovery of PlasticsISBN 978-3-446-18258-5©1996, hardcover, 249,-927 pages/492 figures/208 tables

Recycling and recovery of plastics has gone through tremendous changes during the last years. This handbook represents the most extensive and well-organized compilation of know-how on plastics recycling available to date.

Sponsored by the American Plastics Council.

“... this book will be useful worldwide ... [it] will remain the major treatise on the subject for many years.”

American Plastics Council

Other Applications

MATERIALS

Materials

46

B. Wulfhorst, T. Gries

Textile TechnologyISBN 978-3-446-22963-1©2006, hardcover, 99,90328 pages/225 figures/35 tables

This book provides an overview of the complete process of textile manufacturing. The various raw materials, the different methods of yarn and fabric manufacturing, and an introduction to knitting technology, nonwovens, finishing, and ready-made garment production are described in detail. The book includes a discussion of current recycling processes. To provide a better understanding of the individual textile processes, an example at the end of each chapter describes a particular textile product and the respective processing steps necessary for its manufacture.

Contents: Raw Materials. Yarn Production. Fabric Production. Knitwear Production. Nonwovens Production. Braiding Processes and Machines. Production of Two-dimensional Reinforcing Fabrics. Textile Finishing. Processes and Machines for Making-up. Technical Textiles. Disposal and Recycling of Textiles.

B. Stritzke

Custom Molding of Thermoset ElastomersTooling Techniques, Processes, and Secondary Operations


This book covers chemistry of thermoset elastomers but only to the extent needed for understanding how to process them through a manufacturing environment and how they react in various manufacturing methods. The focus of the book is to provide in-depth coverage of tooling, processing, and secondary operations that can improve manufacturing efficiencies. Detailed and easy to understand diagrams display specific conditions and how they can be improved upon. Innovative ideas and solutions are shared and discussed.

F. Wolff-Fabris, V. Altstädt, U. Arnold, M. Döring

Electron Beam Curing of CompositesISBN 978-3-446-42405-0©2010, hardcover, 89,90136 pages/83 figures/13 tables

Electron beam curing technology for advanced composites has emerged as a credible and attractive alternative to thermal curing for most composite products. Technical advantages, such as aerospace structures, include curing at room temperature, using low-cost tooling, and the ability to fabricate large integrated structure including structures too large to fit inside autoclaves. Studies by aerospace companies have shown potential cost savings of 10-60 % by using electron beam curing.

In this book, both theoretical and practical aspects of electron beam curing of composites are presented, intending to build a bridge between the academic knowledge and the industrial applications.

Other Applications

MATERIALS

47

R. Stauber, L. Vollrath

Plastics in Automotive EngineeringExterior Applications


Today´s automotive industry is challenged by ever more stringent demands to reduce fuel consumption and exhaust emissions. Lightweight design and increased use of advanced plastic components will be crucial for the next generation of cars complying with legislation. Engineers and manufacturers who develop and produce polymer-based components for automotives are under pressure to reduce developing times and to optimize production processes for quality and economic viability. Tools of choice are computer-aided selection of polymers in combination with mathematical simulation for both, material properties and production processes. They provide crucial help in finding innovative and economical solutions when designing polymer applications for modern cars.

S. Selke, J. Culter, R. Hernandez

Plastics PackagingProperties, Processing, Applications, and Regulations 2nd Edition


This book describes the various aspects of coloring plastics, such as the construction of the processing machine, the processing technology, quality assurance of the raw materials and final products, toxicology of the raw materials, and the legal aspects from handling ingredients during the production of a color preparation to the processing of plastic parts. It also includes the safe use of the products made of plastics in their specific applications.

Material properties and how they relate to the chemical structure of the polymers, common processing methods for packaging applications, help with writing specifications, designing, fabricating, testing, and controlling the quality of the plastic materials are covered comprehensively.

Ehrenstein, Pongratz

Polymer ResistanceISBN 978-3-446-41645-1 ©2011, hardcover, approx. 349,- approx. 1372 pages

The resistance of a given polymeric material to certain media or environmental influences is the decisive factor in determining whether it can be used in specific applications.

Reliable and dependable predictions regarding the influence of material manufacturing, compounding, stabilization, processing, part design as well as end use and recycling are necessary to facilitate economically and technologically successful material selection.

This book comprehensively describes the resistance of thermoplastic, thermoset, and elastomric materials as well as their common reinforcements and additives. Extensive tables with resistance properties provide crucial information for material selection for any given application or help stabilize a given material to meet required resistance levels in a specific application.

Other Applications

MATERIALS

Polymer Science

48

D. Hylton

Understanding Plastics TestingISBN 978-3-446-22246-5 ©2004, softcover, 39,90104 pages/56 figures/4 tables

This overview of plastics testing provides an understanding of how polymer structure and morphology affect properties that are important for plastics processing and how to test for these properties. The reader will get an overview of basic material testing, the specific properties tested, and why they are important. The book also provides insight into which tests are useful for predicting the behavior of plastics products after they have been produced and in end-use.

Contents: The Science of Testing. Polymer Rheology. Mechanical Properties and Testing. Thermal Properties and Testing. Viscous Flow Properties Testing. Quality in the Testing Laboratory.

A. Naranjo, M. del Pilar Noriega, T. Osswald, A. Roldán-Alzate, J. Sierra

Plastics Testing and CharacterizationIndustrial Applications


Combined with a solid engineering background, this book provides the information and industrial case studies an engineer needs to both make informed decisions about selecting appropriate testing techniques and effectively troubleshoot problems in the field of plastics manufacturing. The scope of this book also includes relevant and concise information for data interpretation using the most important characterization techniques.

Contents: Spectroscopy. Gas Chromatography and Selective Mass Detection. Thermal Properties. Melt Rheology. Mechanical Properties. Permeability Properties. Environmental Effects and Aging. Electrical, Optical, and Acoustic Properties.

W. Grellmann, S. Seidler

Polymer TestingISBN 978-3-446-40900-2©2007, hardcover, 99,90706 pages/510 figures/27 tables

Testing of plastics provides an insight to the behavior of the material in response to applied loads or exposure to the environment and time. In order to determine the true performance of a plastic material, a comprehensive understanding of the broad range of plastics behavior, such as its mechanical, thermal, electrical, rheological, physical and chemical properties as well as environmental resistance is necessary. In industrial practice, fabricated parts are often tested as part of the design validation step to ensure that end use performance requirements are adequately met.

This book provides a comprehensive discussion of test methods for various properties of plastics, related to different material types and forms, with reference to national, international and application/industry specific test methods in a practical, easy to understand manner.

Testing & Analytics

POLYMER SCIENCE

49

G. Ehrenstein, G. Riedel, P. Trawiel

Thermal Analysis of PlasticsTheory and Practice


Thermal analysis has proven to be one of the most important and meaningful test methods in the plastics industry and in testing laboratories. Although thermal analysis is used for fundamental studies related to materials science of polymers, its power lies in understanding this behavior during manufacturing processes. This understanding aids in process optimization, reduction of manufacturing cycle times, failure analysis as well as overall improvement of the material properties of the finished product, to name a few. In this book, the different test methods and their variations are described in detail, emphasizing the principles and their application in practice. Using practical examples, different approaches to problem solving are presented with a focus on the interpretation of the experimental results.

D. Braun

Simple Methods for Identification of Plastics4th Edition


Processors and users of plastics often need to determine the chemical nature and classification of unknown plastic materials. This highly practical and useful manual enables you to determine the classification of plastics without lab equipment. This is a handy and effective tool for many practical situations.

Contents: Plastics and their characteristics. Analytical procedures. Introduction to the analysis of plastics. Specific identification tests. Screening tests. Advanced analytical methods.

“... compiled by authors who know their subject and know how to get it across in a cogent, understandable man-ner ... recommended without reservation.”

Plastics and Rubber International

Testing & Analytics

POLYMER SCIENCE

G. Ehrenstein, L. Engel, H. Klingele, H. Schaper

SEM of Plastics FailureISBN ISBN 978-3-446-42242-1©2010, hardcover, 199,-272 pages/ 230 figures

Using scanning electron microscopy (SEM) adds a new level of in-depth information to failure research and practical failure analysis. SEM provides up to 250 times the magnification, a wider depth of field, and higher resolution of fractures and fracture surfaces than light microscopy. With this enhanced knowledge it becomes easier to identify not only the type and progression but also the cause of a particular failure occurrence.

This comprehensive collection of SEM photographs of exemplary mechanical, thermal, chemical, and tribological failure cases and their detailed description is an invaluable tool for everyone involved in development, design, quality management, and manufacturing of plastic parts. The book provides the information necessary to assess failure and its causes and to identify corrective measures and preventive actions.

Polymer Science

50

J. Karger-Kocsis, S. Fakirov

Nano- and Micro- Mechanics of Polymer Blends and CompositesISBN 978-3-446-41323-8©2009, hardcover, 199,90624 pages/262 figures

This book gives a state-of-art overview on aspects of micro- and nanomechanics of polymers, polymeric blends and composites. Major issues tackled are the following: experimental techniques to study the mechanical performance of polymer systems especially in respect with molecular, supermolecular and filler architectures on suitable model materials; prediction methods of the mechanical performance (short- and long-term properties); modeling tools and approaches. All these aspects are highlighted on polymeric systems of both academic and practical relevance.

T. Osswald, G. Menges

Materials Science of Polymers for Engineers2nd Edition

ISBN 987-156990-22464-3©2003, hardcover, 79,90640 pages/600 figures/25 tables

This introduction to polymer materials science is divided into three major sections: Basic Principles, Influence of Processing on Properties, and Engineering Design Properties. The first edition of this textbook was praised for its vast number of graphs and data that can be used as reference. The new second edition further strengthens this attribute with a new appendix containing material property graphs for the commonly used polymers. However, the most important change implemented in this edition is the introduction of real-world examples and a variety of problems at the end of each chapter.

J. Dealy, P. Saucier

Rheology in Plastics Quality ControlISBN 978-3-446-21069-1©2000, hardcover, 79,90140 pages/80 figuresIncludes CD

In the global effort to access markets through standardization, the reality in the plastics industry is that many quality professionals are inexperienced in the application of appropriate rheological test methods. This book is aimed at people who set up, manage, or perform tests in industrial quality control laboratories. No previous expertise in the areas of polymer science, quality control, or rheology is necessary for this book to be of practical use. The basics of rheology and statistical process control are presented, along with examples showing how these can be used to solve production problems involving product quality.

Partial Contents: Rheological Properties of Molten Plastics. Quality Assurance – Basic Concepts. Controlling the Measurement Process.

Physics & Chemistry

POLYMER SCIENCE

Polymer Science

www.hanserpublications.com 51

J. Dealy, R. Larson

Structure and Rheology of Molten PolymersFrom Structure to Flow Behavior and Back Again


In recent years, several developments have made it possible to predict the detailed molecular structure of a polymer based on polymerization conditions and to use this knowledge of the structure to predict rheological properties. In addition, new techniques for using rheological data to infer molecular structure have also been developed. Soon, it will be possible to use this new knowledge to design a molecular structure having prescribed processability and end-product properties, to specify the catalyst and reaction conditions necessary to produce a polymer having this structure, and to use rheology to verify that the structure desired has, in fact, been produced.

A. Peacock, A. Calhoun

Polymer ChemistryProperties and Applications


This book provides a comprehensive introduction to the study of polymers. Special emphasis is given to the characteristics that set polymers apart from small molecules, as studied in classic chemistry courses.

The various branches of polymer science are introduced and discussed in a systematic manner, starting from basic chemical structures, continuing through supermolecular organization, and physical properties. Specific examples are used throughout to illustrate how end use relates to the principles under discussion. A series of chapters is devoted to case studies describing the principle classes of synthetic polymers.

M. Szwarc

Ionic Polymerization FundamentalsISBN 978-3-446-18506-7©1996, hardcover, 69,90223 pages/27 figures

This book covers the essential concepts of ionic polymerization and copolymerization, from the initiation of the polymerization reaction, through the propagation phase of the macromolecules, to the termination of growth.

P. Flory

Statistical Mechanics of Chain MoleculesISBN 978-3-446-15205-2©1989, hardcover, 59,90457 pages/100 figures/18 tables

Partial Contents: Analysis of the Spatial Configurations of Chain Molecules and Treatment of Simplified Model Chains. Random Coil Configurations and Their Experimental Characterization. Optical Properties and Radiation Scattering.

Physics & Chemistry

POLYMER SCIENCE

Reference

52

A. Wittfoht

Plastics Technical DictionaryEnglish–German/ German–English

ISBN 978-3-446-16567-0 ©1992, hardcover, 99,901624 pagesThis dictionary contains approximately 18,000 designa-tions and technical terms from polymer chemistry, production, testing, properties and processing of plastics and the corresponding machines, as well as the special vocabulary of certain applications with abbreviations and acronyms.

W. Glenz

A Glossary of Plastics Terminology in 7 LanguagesEnglish – German – Spanish – French – Italian – Russian – Chinese 7th Edition

ISBN 978-3-446-42320-6©2010, book and CD, 89,-480 pages Includes CD

Trying to serve plastics engineers speaking different languages and to breach the language barriers within the international plastics community, the idea was born to compile a glossary of plastics terminology in several languages.

Companion CD: The glossary is now also available in electronic format. For the first time it covers Chinese and Russian as well as English, French, Spanish, Italian, and German translations of approximately 2,200 terms related to chemistry, properties, testing and technology of plastics. In general, the user will find only one translation for any technical term in each language, used most often in the daily work of people involved with plastics.

C. Goetzel, L. Goetzel

Dictionary of Materials and Process EngineeringMaterials, Manufacturing, Processing, Applications

ISBN 978-3-446-17531-0 English–German©1995, hardcover, 149,90753 pages

Thousands of terms, definitions, and concepts are presented, covering a broad range fields, especially in science, research and development, engineering, and related technologies.

“... recommended for its outstanding coverage of technical terms and ... a good buy.”

Polymer News

Dictionaries

REFERENCE

53

Aging and Chemical ResistanceISBN 978-3-446-21697-9©2001, softcover spiral,

24,90128 pages/12 figures

Aging and chemical resistance are probably the most underestimated parameters influencing the performance and lifetime of plastic parts. This quick reference provides an overview of the different interacting aging mechanisms and their influence on plastic parts and their properties. The unique table of chemical resistance delivers information on how the major plastic materials hold up to chemical influences.

Applied Rubber TechnologyISBN 978-3-446-21946-3©2001, softcover spiral,


Belts, seals, hoses, engine mounts, tires—modern life without rubber is incomprehensible. This convenient tool guides you through the selection labyrinth for material blends, additives, compounding equipment, and vulcanization systems. Detailed examples and proven recipes clear your

path to successful design and manufacturing of rubber products.

Extrusion Blow MoldingISBN 978-3-446-21949-8©2001, softcover spiral,


Bottles, canisters, drums, tanks, and ducts—hollow articles made from plastic are indispensable parts of life in the 21st century. This handy tool provides an overview of extrusion blow molding technology: from equipment and fundamentals to process details and design guidelines. Problems with parison? Defects in parts? Turn to this handy troubleshooting guide!

Extrusion Processing DataISBN 978-3-446-331-5©2001, softcover spiral,

24,90128 pages/137 figures You need reliable initial processing data before setting up an extruder to optimize and stabilize the process if you want to guarantee excellent results. A good set up can save you time and money. This reference resource provides

the most important processing data, such as viscosity, thermal properties, and suggested barrel heater temperatures for the most commonly used materials in extrusion.

WeldingISBN 978-3-446-21695-2©2001, softcover spiral,


Whether you produce auto parts, medical applications, or consumer goods, welding of plastics and composites is an important step in their manufacture. This book gives an overview of the welding processes currently used in industrial applications—including their advantages and limitations. Weldability charts for given applications and suggested process parameters together with evaluation methods for weld quality are included.

Plastic Power Series

REFERENCE

Materials

54

55

International Polymer ProcessingThe Journal of the Polymer Processing Society

In English.

Frequency: 5 issues per volume Subscription rate (print inclusive e-access):

648,–* Postage extra Germany: 10,- Foreign countries: 13,- Airmail: 20,– International Polymer Processing covers research and industrial application in the very specific areas of designing polymer products, processes, processing machinery, and equipment.

Kunststoffe internationalMagazine for Plastics

In English. Frequency: monthly Subscription rate (print inclusive e-access): 358,–* Postage extra Germany: 15,60 Foreign countries: 30,00 Airmail: 43,80 Kunststoffe international is the English edition of Kunststoffe. As a subscriber you can additionally download articles from the full-text online archives in English and German free of charge: www.kunststoffe-international.com

Tenside Surfactants DetergentsCleaning Technology Journal

Articles in English, abstracts and news in both English and German Frequency: bimonthly Subscription rate (print inclusive e-access): 398,–* Postage extra Germany: 7,80 Foreign countries: 14,40 Airmail: 18,60 Tenside Surfactants Detergents provides you with the most recent results of research and development in all fields of surfactant chemistry.

All prices are recommended prices only. For Germany they include the VAT. Prices are subject to change without prior notice. Prices valid from 1.10.2010 onwards.

Magazines

HANSER

56

Titles

INDEX

Discovering Polyurethanes ..............................38

EElastomer Processing: Formulas and Tables .......42

Electron Beam Curing for Composites ......... 30, 46

Engineered Rubber Products: Introduction to Design, Manufacture, and Testing ................39

Engineering Biopolymers ................................34

Engineering Thermoplastics: Polycarbonates, Polyacetals, Polyesters, Cellulose Esters ............38

Engineering with Rubber: How to Design Rubber Components 2E ..................................41

Extrusion .....................................................21Extrusion Blow Molding ..................................53

Extrusion Control: Machine – Process – Product ...........................25

Extrusion Dies for Plastics and Rubber: Design and Engineering Computations 3E ..........25

Extrusion of Polymers: Theory & Practice 2E .....24

Extrusion Processing Data ..............................53

FFatigue, Stress and Strain of Rubber Components .................................................39

Fibers & Films ...............................................43The First Snap-Fit Handbook: Creating and Managing Attachments for Plastics Parts 2E ........................................ 5

Flame Retardants for Plastics and Textiles: Practical Applications ...................................44

GGas-Assist Injection Molding: Principles and Applications .............................15

AAdditives & Colors ..........................................44Adhesion and Adhesives Technology: An Introduction 2E ........................................30

Aging and Chemical Resistance .......................53

Applied Rubber Technology .............................53

BBlow Molding ................................................26 Blow Molding Design Guide 2E ........................26

Blow Molding Handbook .................................27

Blown Film Extrusion .....................................24

CColoring of Plastics ................................. 14, 45

The Complete Part Design Handbook: For Injection Molding of Thermoplastics ............ 4

Compression Molding .....................................31

Co-Rotating Twin-Screw Extruders: Fundamentals, Technology, and Applications ....25

Custom Molding of Thermoset Elastomers: Tooling Techniques, Processes, and Secondary Operations ....................................46

DDesign Formulas for Plastics Engineers 2E .......... 6

DESIGN .................................................... 4–9Designing Plastic Parts for Assembly 6E ............. 4

Designing with Plastics ................................... 4

Dictionaries ..................................................52Dictionary of Materials and Process Engineering .................................................52

57

Titles

INDEX

JJoining of Plastics: Handbook for Designers and Engineers 3E ............................. 5

KKunststoffe international: Magazine for Plastics ............................... 33, 45

LLiquid Composite Molding ..............................33

MMaterials Science of Polymers for Engineers 2E .......................................... 37, 50

MATERIALS ............................................34–47Microcellular Processing .................................32

Mixing & Compounding ...................................13Mixing and Compounding of Polymers: Theory and Practice 2E ...................................13

Mold Engineering 2E ....................................... 8

Moldflow Design Guide: A Resource for Plastics Engineers ................................... 11, 17

Mold-Making Handbook 2E ............................... 8

NNano- and Micro-Mechanics of Polymer Blends and Composites ..................................50

OOther Industry Applications .............................45Other Processes .............................................30

PPhysics & Chemistry .......................................50Plastic Part Design for Injection Molding: An Introduction 2E ......................................... 5 Plastic Pocket Power Series ..............................53Plastic Surface Modification: Surface Treatment, Decoration, and Adhesion ...............................30

Gastrow Injection Molds: 130 Proven Designs 4E ...............................9, 20

A Glossary of Plastics Terminology in 7 Languages English – German – Spanish – French – Italian – Russian – Chinese 7E ........................52

HHandbook of Engineering Biopolymers: Homopolymers, Blends, and Composites ...........36

Handbook of Polymeric Foams and Foam Technology 2E ......................................36

Hollow Plastic Parts: Design and Manufacture .................................26

Hot Runner Technology ..............................6, 19

How to Improve Rubber Compounds: 1500 Experimental Ideas for Problem Solving ....40

How to Make Injection Molds 3E ..................9, 19

IIndustrial Polymers .......................................35

Injection Mold Design Engineering ..............8, 19

Injection Molding ..........................................15Injection Molding: An Introduction 2E ............16

Injection Molding: Fundamentals and Applications .................................................15

Injection Molding Handbook 2E .......................16

Injection Molding Machines: A User’s Guide 4E ..........................................18

International Plastics Handbook: The Resource for Plastics Engineers 4E ....... 11, 37

International Polymer Processing: The Journal of the Polymer Processing Society ......................................29Ionic Polymerization Fundamentals ..................51

58

Titles

INDEX

Polymeric Materials: Structure, Properties, Applications .................................35

Polymeric Nanocomposites: Theory and Practice .......................................38

Polyolefins: Processing, Structure Development, and Properties ..........................35

Polypropylene Handbook 2E ............................34

Precision Injection Molding: Process, Materials and Applications ..............................17

PROCESSING & MANUFACTURING ..............10–33Processing of Composites ...............................32

Product Design ............................................... 4PVC Handbook ..............................................34

RRapid Prototyping .........................................10Reactive Polymer Blending ....................... 14, 31

Recycling .....................................................45Recycling and Recovery of Plastics ...................45

REFERENCE ............................................52–53Resins for Coatings: Chemistry, Properties and Applications ............................42

Rheology in Plastics Quality Control .................50

Robust Process Development and Scientfic Molding .......................................................15

Rotational Molding: Design, Materials, Tooling, and Processing ...................33

Rubber ........................................................39Rubber Processing: An Introduction ................41

Rubber Processing: Technology – Materials – Principles ....................................42

Rubber Technology: Compounding and

Plastics Additives Handbook 6E .......................44

Plastics and Coatings: Durability – Stabilization – Testing ..................................43

Plastics and Composites Welding Handbook .......31

Plastics Extrusion Technology 2E .....................23

Plastics Failure Guide: Cause and Prevention ....................................10

Plastics Flammability Handbook: Principles – Regulations – Testing and Approval 3E .............44

Plastics in Automotive Engineering: Exterior Applications .....................................47

Plastics Manufacturing Systems Engineering ......10

Plastics Packaging: Properties, Processing, Applications and Regulations 2E ......................47

Plastics Technical Dictionary: English–German/German–English ....................52

Plastics Testing and Characterization: Industrial Applications ...................................48

Polymer Blends: A Comprehensive Review ........36

Polymer Chemistry: Properties and Applications ............................51

Polymer Extrusion 4E .....................................23

Polymer Mixing: A Self-Study Guide .................13

Polymer Mixing: Technology and Engineering .................................................13

Polymer Processing: Modeling and Simulation ...................................................12

Polymer Resistance ........................................47

POLYMER SCIENCE ...................................48–51Polymer Testing ............................................48

59

Titles

INDEX

Thermoplastic Foam Extrusion: An Introduction ...................................... 26, 28

Tool Design.................................................... 9Training in Injection Molding 2E .....................18

Training in Plastics Technology 2E ...................11

Troubleshooting the Extrusion Process: A Systematic Approach to Solving Plastic Extrusion Problems 2E .........................21

Twin Screw Extrusion 2E .................................22

UUnderstanding Additive Manufacturing .............. 7

Understanding Blow Molding 2E ......................27

Understanding Compounding ..........................14

Understanding Design of Experiments ...............12

Understanding Extrusion 2E ............................21

Understanding Injection Mold Design ...........7, 20

Understanding Injection Molding Technology ..................................................17

Understanding Plastics Testing ........................48

Understanding Polymer Processing ...................12

Understanding Product Design for Injection Molding .......................................... 6

Understanding Thermoforming 2E ....................28

Understanding Thermoplastic Elastomers...........40

WWelding .......................................................53

Testing for Performance 2E .............................39

Runner and Gating Design Handbook: Tools for Successful Injection Molding 2E......9, 20

SSEM of Plastics Failure ...................................49

Screw Extrusion ............................................23

Selecting Injection Molds: Weighing Cost versus Productivity................6, 20

Simple Methods for Identification of Plastics 4E ...............................................49

Solid Phase Processing of Polymers ..................32

SPC in Injection Molding and Extrusion 2E .. 16, 22

Statistical Mechanics of Chain Molecules ..........51

Structure and Rheology of Molten Polymers: From Structure to Flow Behavior and Back Again ............................................51

Structure Formation in Polymeric Fibers ............43

Synthetic Fibers: Machines and Equipment Manufacture, Properties ..................43

TTechnology of Thermoforming .........................29

Testing & Analytical Methods ...........................48Textile Technology ........................................46

Thermal Analysis of Plastics: Theory and Practice .......................................49

Thermoforming ..............................................28Thermoforming: A Practical Guide ...................28

Thermoplastic and Rubber Compounds: Technology and Physical Chemistry ............ 37, 41

Thermoplastic Elastomers 3E ...........................40

60

Authors

INDEX

FFakirov, S. ............................................. 36, 50Flory, P. ......................................................51Fourné, F. ...................................................43Freitag, W. ..................................................42

GGebhardt, A. ...........................................7, 10Gent, A. .....................................................41Glenz, W. ....................................................52Goetzel, C. ..................................................52Goetzel, L. ..................................................52Gramann, P. .......................................... 16, 31Greener, J. ..................................................17Greif, H. .....................................................18Grellmann, W. ..............................................48Grewell, D. ..................................................31Gries, T. ......................................................46Gupta, R. ....................................................38

HHarris, H. ....................................................25Hensen, F. ..................................................23Hernandez, J. ..............................................12Hernandez, R. ..............................................47Holden, G. ..................................................40Hu, G. .................................................. 14, 31Hylton, D. ...................................................48

IIllig, A. ......................................................28Isayev, A. ...................................................15

JJohannaber, F. .............................................18Johnson, P. .................................................41

KKamal, M. ............................................. 15, 38Karger-Kocsis, J. ..........................................50Kazmer, D. ........................................ 8, 10, 19Kim, K. ................................................. 37, 41Kleemann, W. ..............................................42Klempner, D. ...............................................36Klingele, H. ...................................................49Kohlgrüber, K. .............................................25Kretzschmar, G. ............................................18Kricheldorf, H. .............................................40Kulkarni, S. .................................................15

AAltstädt, V. ............................................. 30, 46Arnold, U. ............................................... 30, 46Avery, J. .....................................................15

BBaker, W. .............................................. 14, 31Bauman, J. .................................................39Baur, E. ................................................ 11, 37Beall, G. ............................................. 26, 33Beaumont, J. ............................................... 9Benatar, A. .................................................31Bhattacharya, S. ..........................................38Bhattacharyya, D. ........................................36Bittner, M. ..................................................45Bonenberger, P. ............................................ 5Bottenbruch, L. ...........................................38Brandrup, J. ................................................45Braun, D. ....................................................49Brinkmann, S. ....................................... 11, 37

CCalhoun, A. .................................................51Campo, E. ...............................................4, 35Cantor, K. ...................................................24Catoen, B. ..............................................6, 20Choi, D. ......................................................35Chung, C. ....................................................24Coates, P. ...................................................32Coran, A. ....................................................13Culter, J. ....................................................47

DDaniels, C. ..................................................34Davé, R. .....................................................32Davis, B. .....................................................31Dealy, J. ............................................... 50, 51Del Vecchio ...................................................12Dick, J. ................................................ 39, 40DiMattia, D. ................................................27Döring, M. .............................................. 30, 46Dumoulin, M. ..............................................32

EEhrenstein, G. ..................................35, 47, 49Ehrig, F. .....................................................18Endres, H.J. ..................................................34Engel, L. .......................................................49Erhard, G. .................................................... 4Ezrin, M. .....................................................10

61

Authors

INDEX

SSalem, D. ....................................................43Saucier, P. ...................................................50Schaper, H. ...................................................49Schmachtenberg, E. ................................ 11, 37Schumacher, G. ............................................. 6Scott, C. ............................................... 14, 31Seidler, S. ...................................................48Selke, S. .....................................................47Sendijarevic, V. ............................................36Shoemaker, J. ........................................ 11, 17Siebert-Raths, A.............................................34Sierra, J. ....................................................48Sommer, J. ..................................................39Stauber, R. ..................................................47Stoeckhert, K. .............................................. 8Stoye, D. ....................................................42Stritzke ........................................................46Summers, J. ................................................34Szwarc, M. ..................................................51

TThrone, J. ........................................26, 28, 29Trawiel, P. ...................................................49Tres, P. ........................................................ 4Troitzsch, J. ................................................44Turng, L. .....................................................16

UUhlig, K. .....................................................38Unger, P. ........................................6, 9, 19, 20

VVollrath, L. ..................................................47Vossebürger, F. .............................................11

WWard, I. ......................................................32Weber, K. ....................................................42Weil, E. D. ....................................................44White, J. ..........................13, 22, 23,35, 41, 42Wildi, R. .....................................................14Wilkes, C. ....................................................34Wimberger-Friedl, R. .....................................17Wittfoht, A. ................................................52Wolff-Fabris, F. ........................................ 30, 46Wolf, R. ......................................................30Wolters, L. ..................................................11Wulfhorst, B. ...............................................46

ZZweifel, H. ..................................................44

LLarson, R. ...................................................51Lee, N. ................................................. 26, 27Levchik, S. V. ................................................44Liu, S. ........................................................15Loos, A. ......................................................32

MMaier, C. .....................................................14Malloy, R. .................................................... 5Manas-Zloczower, I. ......................................13Menges, G. ............................ 11, 21, 36, 46, 50Mennig, G. ..................................................10Michaeli, W. ................. 9, 11, 16, 18, 19, 25, 45Moet, A. .....................................................13Mohren, P. ..............................................9, 19Müller, A. .............................................. 14, 45

NNaranjo, A. .................................................48Noriega, M. ........................................... 21, 48

OOberbach, K. ......................................... 11, 37Okamoto, K. ................................................32Osswald, T. ................. 11, 12, 16, 31, 37, 48, 50

PPark, Y. ......................................................31Parnas, R. ...................................................33Pasquini, N. ................................................34Peacock, A. .................................................51Pocius, A. ...................................................30Potente, H. .................................................23Pötsch, G. ...................................................16

QQuirk, R. .....................................................40

RRao, N. ........................................................ 6Rauwendaal, C. ...................... 13, 16, 21, 22, 23Rees, H. .................................... 6, 7, 8, 17, 20Riedel, G. ...................................................49Rios, A. ......................................................31Robeson, L. .................................................36Roldán-Alzate, A. .........................................48 Rosato, A. ..................................................27Rosato, D. ..................................................27Rotheiser, J. ................................................. 5Ryntz, R. ....................................................43

6262

Order Directly: Quick and Easy per Fax!

ORDER FORM / FAX SHEET

ORDER FORM / FAX SHEET

Order Directly: Quick and Easy per Fax!(For Fax Number See Back of Catalogue)

58

copy(ies) Author/Title ISBN 978-3-446- Price




Shipping costs will be charged depending on your choice of delivery: air mail surface mail

Address:Company address Private address

Mr. Ms.First Name Name

Company

VAT No.

Department Position

Street / P.O. Box

Country / City / ZIP Code

E-Mail

Date / Signature

122 013

Please charge my credit card account:

Visa American Express Euro-/Mastercard Diners Club

Card. No.

Date of expiry Amount (Shipping costs will be added)

(for Fax Number See Back of Catalogue)

Carl Hanser Verlag · Kolbergerstrasse 22 · 81679 Munich/Germany · Tel.: +49/89/998 30-303 · Fax: +49/89/98 48 09 · [email protected] · www.kunststoffe-international.com

T E C H N I C A L M AG A Z I N E S | T E C H N I C A L BO O K S | O N L I N E S E R V I C E S | S E M I N A R S

Lives up to its Promise

SO DOES KUNSTSTOFFE INTERNATIONAL. The English edition of the well-

established German magazine KUNSTSTOFFE provides you with approx. 700 pages

annually of up-to-date information. Here you can read exclusive articles on materials,

processing and application.

IN THE ONLINE PORTAL KUNSTSTOFFE-INTERNATIONAL.COM you can find

not only the online archives in English and German – for subscribers free of charge –

but also our complete range of plastics information.

ORDER YOUR FREE SAMPLE COPY NOW! Quick and easy online at

www.kunststoffe-international.com

559/89009

Carl Hanser VerlagP.O. Box 86 04 2081631 Munich/GermanyTel.: +49/89/998 30-264Fax: +49/89/998 [email protected]

Plastics Books - Hanser Fachbuch

Documents

Transcript of Plastics Books - Hanser Fachbuch