Plasma Cutting Machine - NISSAN...
2
Plasma Cutting Machine High productivity brought out at cutting shops! Outstanding features of KT-790PMX, which is being well-reputed because of high-quality beveling and cost saving by fast plasma-cutting process, are inherited to KT-790PJX. And KT-790PJX has realized further higher workability to meet demands from cutting shops. KT-790PJX, that has been reduced its cost by using newly developed Beveling Unit and has been downsized, shall surely provide great productivity to International market widely. KT-790PJX, that has pursued farther high speed process, high-quality, high efficiency 1. New bevel cutting unit Newly developed RA （ Rotate/Angle ） style bevel cutting unit, which is lighter/smaller/higher-rigid than conventional High Speed Link Style and TCL Style, is employed to improve not only movement speed, but maintenability as well. 2. Improved operability PCNC （FANUC FS31iB＋Panel i ） is adopted to enhance Drawing Function. Real-time Drawing Function that shows you the current cutting-position and total cutting time while running a program, Document Viewer Function that can see Manuals on the screen, these two functions have been available on the machine. 3. Improved cutting quality Newly developed Cut-condition Setting Function utilizing functions of PCNC enables you to set Cutting Conditions （AC current/Flow rate/etc ） through NC controller. You can select Cutting material, Material thickness, Type of corner rope through NC controller, and the cutting can be done with much more suitable conditions.
Transcript of Plasma Cutting Machine - NISSAN...
Plasma Cutting Machine
High productivity brought out at cutting shops!Outstanding features of KT-790PMX, which is being well-reputed because of high-quality beveling and cost saving by fast plasma-cutting process, are inherited to KT-790PJX. And KT-790PJX has realized further higher workability to meet demands from cutting shops. KT-790PJX, that has been reduced its cost by using newly developed Beveling Unit and has been downsized, shall surely provide great productivity to International market widely.
KT-790PJX, that has pursued farther high speed process, high-quality, high efficiency
1. New bevel cutting unitNewly developed RA （Rotate/Angle） style bevel cutting unit, which is lighter/smaller/higher-rigid than conventional High Speed Link Style and TCL Style, is employed to improve not only movement speed, but maintenability as well.
2. Improved operability PCNC （FANUC FS31iB＋Panel i） is adopted to enhance Drawing Function. Real-time Drawing Function that shows you the current cutting-position and total cutting time while running a program, Document Viewer Function that can
see Manuals on the screen, these two functions have been available on the machine.
3. Improved cutting qualityNewly developed Cut-condition Setting Function utilizing functions of PCNC enables you to set Cutting Conditions
（AC current/Flow rate/etc） through NC controller. You can select Cutting material, Material thickness, Type of corner rope through NC controller, and the cutting can be done with much more suitable conditions.
Caution！
790PJX-01’13.02 NPC 2000
http://nissantanaka.com
The specifications are subject to change for improvement without notice.
Manufactured by :
No.11,Chikumazawa, Miyoshi, Iruma-gun, Saitama, 354-8585 JapanTEL : + 81-49-258-4412 FAX : + 81-49-258-4858
Plasma Cutting Machine
KT-790PJX Main specifications
Rail span
Effective cutting width
Rail length
Effective cutting length
Rail / rack size
NC controller
Speedspecification
Plasma cuttingapparatus
4,000～6,500mm
Rail span－1,000mm
Up to 50,000mm（Without cable-bearer less friction device）Up to 100,000mm（With cable-bearer less friction device）
Rail length－3,000mm
37kg/m rail（CP6）/50kg/m rail（CP6, CP10 and CP16）
FANUC 31iB＋Panel i
Cutting speed : 0～10,000mm/minRapid speed : 30,000mm/minManual rapid speed : 12,000mm/minCutting head lift up/down speed : 18,000mm/min
PEGASUS 500 orHPR-400XD （HYPERTHERM INC）
OV
ER
ALL
MA
CH
INE
LE
NG
TH 2
673
292
270
OV
ER
ALL
MA
CH
INE
HE
IGH
T 17
3215
030
0
EFFECTIVE CUTTING WIDTH 4000
RAIL SPAN 5000
OVERALL MACHINE WIDTH 5600
5980
500
380
50
3001801230
1690460
3261657690
983
KT-790PJX machine body external view
Standardfunctions
Optionalfunctions
● Bevel cutting unit（RA style）● Initial height controller● Cutting height controller （Arc height control style）● Coordinate rotation function● Scheduled operation function● Operator’ s deck● Area sensor
● Stainless steel cutting● R-chamfering function （Only for PEGASUS 500）● Bottom 40 degree beveling function （Only for PEGASUS 500）● Powder marking device● Ink-jet marking device● Positioning camera● Dust collector （Stand-alone type）
Saitama factory is certified as ISO 9001 factory Registration No : 99QR - 156Scope of product / Service : Design and Manufacturing of Gas Cutting Machine, Plasma Cutting Machine and Laser Cutting Machine
●The person who operates Plasma Cutting Machine shall be required to take an adequate training based on regulations/laws/etc of each country.●Be sure to read through "Instruction Manual" beforehand, to properly operate the machine.
