Piping Fittings Calculator
description
Transcript of Piping Fittings Calculator
TOTAL W.O
LE
T
219.80 Sch. 90º 45º 90º 45º 90º 45º EQ. CO/10S 40 80 150# 300# 600# 900#
###
1Os 10 20 30 40 80 10S 40 80 10S 40 80 10S 40 80
m m m m m m pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs
½" ###
¾'' ###
1'' ###
1½'' ###
2'' ###
2½'' ###
3'' ###
4'' ###
5'' ###
6'' 5.0 2 1.0 2.0 ###
8'' ###
10'' ###
12'' ###
14'' ###
16'' ###
18'' ###
20'' ###
22'' -
24'' ###
26'' ###
28'' -
30'' ###
32'' -
34'' -
36'' ###
38'' -
40'' ###
42'' ###
44'' -
46'' -
48'' ###
CRISTIANELBOW TEE Reducer CAP WN FLANGE PIPE
Main DIAMETER Branch Diameter
2xR 2xr
1219.2 609.6
1219.2 609.6
Suplimentary length to be cut out.x VALUE 527.93 mmw VALUE 557.30 mm
R -x = 81.6709ThicknessQuoted Length 845
Branch Length 318.07 ANGLE 90°
Branch Length 287.70 ANGLE 45°
rx
ENTER DATA
Main pipe = 20" 45º branch = 8"
Main pipe = 22"90º branch = 20"
© Iuhas Cristian Bonny -Island 2001
ANGLE 90°
ANGLE 45°
ENTER DATA
© Iuhas Cristian Bonny -Island 2001
Trunion
ADITIONAL LENGTHx = 101.80
H = 134.58
QUOTED LENGTH90
CUTTING LENGTH191.80
Elbow 90º
Drawing : Irimia AntonProgram: Cristian Iuhas
Bonny Island 2001
Particular case: 14" ELBOW 900 with 10" TRUNION
R = 4" Head pipeB = 4" BranchD1 = 228 mmE = Full encirclement
shall be used.VENT HOLE
Pad material shall be the same as the main pipe.
Reinforcement pads may be divided into halves
with a longitudinal welded seam, and ventholewith a longitudinal welded seam, and vent hole on each half. on each half.
Branch attachement welds shall be in accordance
with ANSI B31.3
For sizes not shown, consult with sttress analyst.
12
3
4
NOTE :
BRANCH 90º
NOMINAL SIZE
BRANCH 45º
NIGERIA LNG PROJECT
SHELL STANDARD FOR REFINERY COMPLEX.
Reinforcing pad thickeness shall not be less than the thicknes of the header. The reinforcing pad material shall be the same nominal material as the header and equal or higher stress value.
1. The reinforcing pad width 'L' shall not be less than that specified .2. The pad shall be positioned so that the top of the pad extends an equal distance from outside surface of the branch on either its side.
WIDTH ' L' [mm]
© Iuhas Cristian Bonny -Island 2001
214.30 mm261.64 mm
Pad material shall be the same as the main pipe.
Reinforcement pads may be divided into halves
with a longitudinal welded seam, and ventholewith a longitudinal welded seam, and vent hole on each half. on each half.
Branch attachement welds shall be in accordance
with ANSI B31.3
For sizes not shown, consult with sttress analyst.
BRANCH 90º
NOMINAL SIZE
BRANCH 45º
NIGERIA LNG PROJECT
SHELL STANDARD FOR REFINERY COMPLEX.
1. The reinforcing pad width 'L' shall not be less than that specified .2. The pad shall be positioned so that the top of the pad extends an equal distance from outside surface of the branch on either its side.
WIDTH ' L' [mm]
© Iuhas Cristian Bonny -Island 2001
RAPID CALCULATOR
57 mm ADD EXTR. ADD EXTRACT RESULT236 57 4642205 57
76 mm 6270 350350 SS
57 mm 300 2"-20"140 mm 402 24"
334 30"273.00 485136.50 190 CS&ITCS
6.35 200 2"- 16"240 >18"
127 1750440
555
660.00
13957
464
SCH
SIZE
RED.
TEE
FLANGE
O.D.
THK½ OD
WELDOLET
© Iuhas Cristian Bonny -Island 2001
ELBOW
VALVE
DELETE
CLEAR
6m - 8m 6 m
12m | 6m6m
CS&ITCS11m-13m 12m
© Iuhas Cristian Bonny -Island 2001
NIPOFLANGE
SIZEWEIGHT [Kg]
150 300 600½" 3.421" 4.09 4.79 5.49
1½" 7.72
NIPOLET½" 1.921" 2.99
1½" 4.42 Kg
RANDOMS SIZECS 3" 4" 24"
11954 12053 11835
12055 12042 11825
11957 12045 11830
SS 6" 10" 20" 24"6020 6560 6020 6015
6295 6042 6020
6710 6045 6025
6785
ITCS 2" 6" 8" 18"12045 13043 13500 9225
13138
12972