Piping Accessories EMPLOYEE OWNED - Construction

54 years of excellence... www.thybar.com 82

EMPLOYEE OWNED

TM

Piping Accessories

TCC-5 Pipe Penetration System




EMPLOYEE OWNED

TM

Piping Accessories

Table of Contents

General Information 84

Specifications 85

Assembly Instructions 86

Submittal 87-95


EMPLOYEE OWNED

TM

Piping Accessories

General Information

Pipe Roller Supports Thybar Corporation pipe roller supports are provided with painted roller, 18” threaded rods, nuts and spring nuts. Hold down brackets are optional. The support has a continuous wood nailer covered by removable counter flashing for an effective method of attaching roofing felts. Water-tight installation is assured. The equipment mounting supports are available in three basic styles as shown in this catalog. Optional Features 1. Equipment support height addition 2. Construction to fit roof pitches 3. Chemically treated wood nailers 4. Several rollers may be lined up horizontally or vertically 5. Equipment support may be any length to suit conditions Dektite Pipe Flashings Made of long life, flexible, weatherproof gray EPDM rubber or silicone Flexible, corrosion resistant aluminum base conforms to any panel configuration EPDM and silicone will not crack or break Pipe diameter markings are clearly indicated for accurate fitting Designed for 1/4” to 24” diameter pipes One piece construction is easy to install Pleated cone adjusts to any roof pitch and allows for complete flexibility EPDM has a continuous service temperature range of -30ºF to + 250ºF Silicone has a continuous service temperature range of –40ºF to + 350ºF Proven resistance to ozone and ultra-violet light Graduated Boot Pipe Penetration Systems Thybar Corporation piping covers feature ABS Thermoplastic Korad Acrylic Cover, Graduated Boots Molded or Weather-Resistant Plastisol and (2) Stainless Steel Pipe Clamps per Boot. Available Configurations: 1. TCC-1: 12” Collar Accommodates Pipes 6” to 10” nominal 2. TCC-3: 3 1/2” & 6 1/2” Collars Accommodates Pipes 1/2” to 5” nominal 3. TCC-5: 3 1/2” Collars Accommodates Pipes 1/2” to 2 1/2” nominal


EMPLOYEE OWNED

TM

Piping Accessories

Specifications

TC-1, TC-2 • Provided with 2” x 6” wood nailer. Prime G-90 galvanized steel 18 gauge Fully welded and mitered corners Base flange attachments for securing equipment mounting supports to

the building structure 1 1/2” thick 3 lbs. density rigid insulation 3” cant with step for deck insulation 20 gauge insulted counter flashing cap ASTM A653/A653M

TC-3 • Provided with 2” x 6” wood nailer. Prime G-90 galvanized steel 18 gauge Fully welded and mitered corners Base flange attachments for securing equipment mounting supports to the building

structure 1 1/2” thick 3 lbs. density rigid insulation 20 gauge insulted counter flashing cap ASTM A653/A653M


EMPLOYEE OWNED

TM

Piping roof curb assembly instructions are to be used as general guidelines only. Included with shipment are as-built drawings for proper location of sections and channels. Use as-built drawings to identify and locate

match-marked sections (1-1, A-A, etc..)

If Piping Accessory curb assembly will not be installed and roofed-in upon receipt, it is recommended that piping accessory should be stored level and adequately supported to avoid damage and, a clean, dry location to avoid

possible corrosion problems associated with extended contact with the ground.

If the piping accessory curb will be mounted on a new building, it can be assembled at any convenient location and installed as soon as the roof support members are in place. As a general rule, the curb should be placed directly on the roof support members, use tack welding (or other equivalent fastening method) to secure the curb in place.

As an alternative, the roof curb can also be mounted on a roof deck. When a deck is used, be sure to provide additional blocking directly below the curb flanges to give further support and minimize vibration.

Assembling Roof Curb

1. Select an area conveniently located near the unit installation site, and open the curb shipping carton(s). Verify that all materials, nuts, bolts and gasketing, were received.

2. Caulk all seams and fasten with self-drilling sheet metal screws. 3. Apply adhesive backed gasketing provided with curb to the entire perimeter of the top of

roof curb. 4. Install piping cover. Note: These instructions are meant as a general guide only. Some variations may

occur, refer to as-built drawings before proceeding.

Piping Accessories

Assembly Instructions


EMPLOYEE OWNED

TM

Piping Accessories

TEMS-1 With Multiple Pipe Roller Assemblies Equipment Supports Deck

Submittal

Model Slope Remarks

Addison Corporate Office 913 S. Kay Avenue Addison, IL 60101 Ph: (630) 543-5300 Fax: (630) 543-5309 800-666-CURB (2872)

Farmers Branch Office 13801 Senlac Drive Farmers Branch, TX 75234 Ph: (972) 416-6220 Fax: (972) 418-6713 800-777-CURB (2872)

Akron Office

Burt Manufacturing Co. 44 E. South Street Akron, OH 44311 Ph: (330) 762-0061 Fax: (330) 762-0914 800-837-CURB (2872)

Louisville Office

10200 Bunsen Way Louisville, KY 40299 Ph: (502) 499-5480 Fax: (502) 499-5481 800-993-CURB (2872)

McCarran Office

711 Denmark Drive McCarran, NV 89434 Ph: (775) 343-0600 Fax: (775) 343-0606 866-917-CURB (2872)

Provide amount of pitch, direction and minimum

height, if necessary.

12”


EMPLOYEE OWNED

TM

Piping Accessories

TEMS-2 With Multiple Pipe Roller Assemblies Equipment Supports for Deck

Submittal

Model Slope Remarks



Akron Office


Louisville Office


McCarran Office




12”


EMPLOYEE OWNED

TM

Piping Accessories

TEMS-3 With Multiple Pipe Roller Assemblies Equipment Supports Deck

Submittal

Model Slope Remarks



Akron Office


Louisville Office


McCarran Office




12”


EMPLOYEE OWNED

TM


Submittal

ABS Thermoplastic Korad Acrylic Cover 12” Collar Accommodate Pipes 6” to 10” Nominal Boots Graduated for Standard Pipe Sizes Boots Mold of Weather Resistant Plastisol 2 Stainless Steel Pipe Clamps Included per Boot

Standard Features:

Heavy gauge galvanized steel 2” X 2” Wood Nailer Model Slope Remarks



Akron Office


Louisville Office


McCarran Office




12”


EMPLOYEE OWNED

TM


Submittal

ABS Thermoplastic Korad Acrylic Cover 3 1/2” & 6 1/2” Collars Accommodate Pipes 1/2” to

5” Nominal Boots Graduated for Standard Pipe Sizes Boots Mold of Weather Resistant Plastisol 2 Stainless Steel Pipe Clamps Included per Boot

Standard Features:

Heavy gauge galvanized steel 2” X 2” Wood Nailer



Akron Office


Louisville Office


McCarran Office




12”

Model Slope Remarks


EMPLOYEE OWNED

TM

Pre-Fabricated Roof Curbs TC-1 Curb With TP-2 Piping Cover

Submittal

Standard Features: 1. Factory installed 2” x 6” wood nailer 2. Welded 18 gauge galvanized steel shell and base

plate 3. 1 ½” thick, 3 lbs. rigid insulation 4. 1” Cap insulation 5. Fully mitered 3” cant with step for deck insulation 6. 20 gage counter flashing cap

Model Slope Remarks



Akron Office


Louisville Office


McCarran Office


12”




EMPLOYEE OWNED

TM

Model Slope Remarks


Submittal



Akron Office


Louisville Office


McCarran Office


12”




EMPLOYEE OWNED

TM



Akron Office


Louisville Office


McCarran Office


Model Slope Remarks


Submittal



12”


EMPLOYEE OWNED

TM



Akron Office


Louisville Office


McCarran Office


Vibro-MateTM

Piping Accessories EMPLOYEE OWNED - Construction

Documents

Transcript of Piping Accessories EMPLOYEE OWNED - Construction