Pinout diagram - Adafruit Industries · USB to serial converter Micro SD card reader Ambient light...
1
USB to serial converter Micro SD card reader Ambient light sensor (LTR-329ALS-01) Barometric pressure sensor and almeter (MPL3115A2) USB Charge indicator LED JST for LiPo baery (450mA) (BQ24040) Temperature and humidity sensor (Si7006-A20) Power GND Serial Pin External IO Pin Control Correct Board Mounng RGB LED must be at the top of the board, above the USB connector * Interrupts EXT_IO0, EXT_IO4 & EXT_IO5 are connected to a PIC and are accessible via Pycom Libraries RGB LED Pinout diagram 5V GND 3V3 1357 2468 9 10 G10 G9 G8 SD_CLK SDA SCL G7 G6 G30 G31 G3 G0 G4 G5 Accelerometer Interrupt G2 G1 G23 G24 G11 G12 G13 G14 G15 G16 G17 G22 G28 UART_RX P0 P1 P2 P3 P4 P8 P23 P22 P21 P14 P13 P9 P10 P11 UART_TX RGB_LED PWR_EN SD_CMD SD_DAT EXT_IO1 EXT_IO2 EXT_IO3 Button Accelerometer (LIS2HH12), Ambient Light (LTR-329ALS-01), Barometric (MPL3115A2), Humidty and Temperature (Si7006-A20) External IO Header Reset 5 1 2 3 4 10 9 8 7 6 GND PWR_EN 3V3_Sensors 3V3_Pymodule EXT_IO0 (RGB_LED) EXT_IO1 EXT_IO2 EXT_IO3 EXT_IO4 EXT_IO5 Distributed by Pycom Ltd. Copyright © 2017 by Pycom Ltd. All rights reserved. No part of this document may be reproduced, distributed, or transmied in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior wrien permission of Pycom Ltd, except in the case of brief quotaons embodied in crical reviews and certain other noncommercial uses permied by copyright law. To order contact [email protected] Buon Accelerometer (LIS2HH12)
Transcript of Pinout diagram - Adafruit Industries · USB to serial converter Micro SD card reader Ambient light...
USB to serial converter
Micro SD card reader
Ambient light sensor (LTR-329ALS-01)
Barometric pressure sensor and altimeter (MPL3115A2)
USB
Charge indicator LED
JST for LiPo battery (450mA)(BQ24040)
Temperature and humidity sensor (Si7006-A20)
PowerGNDSerial PinExternal IO PinControl
Correct Board MountingRGB LED must be at the top of the board, above the USB connector
* Interrupts EXT_IO0, EXT_IO4 & EXT_IO5 are connected to a PIC and are accessible via Pycom Libraries
RGBLED
Pinout diagram
5VGND3V3
1 3 5 7
2 4 6 8
9
10
G10G9G8
SD_CLKSDASCL
G7G6G30G31G3G0G4G5 Accelerometer Interrupt
G2G1G23G24G11G12G13G14G15G16G17G22G28
UART_RXP0P1P2P3P4
P8
P23P22P21
P14P13
P9P10P11
UART_TXRGB_LEDPWR_ENSD_CMD
SD_DATEXT_IO1EXT_IO2EXT_IO3 Button
Accelerometer (LIS2HH12), Ambient Light (LTR-329ALS-01), Barometric (MPL3115A2), Humidty and Temperature (Si7006-A20)
External IO Header
Reset
5
1234
109876
GNDPWR_EN3V3_Sensors3V3_PymoduleEXT_IO0 (RGB_LED)EXT_IO1EXT_IO2EXT_IO3EXT_IO4EXT_IO5
Distributed by Pycom Ltd.Copyright © 2017 by Pycom Ltd. All rights reserved. No part of this document may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior
written permission of Pycom Ltd, except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted by copyright law.
To order contact [email protected]
Button
Accelerometer (LIS2HH12)
