pH ISM Qualification Kit Instruction manual ... ISM Qualification Kit Instruction manual...

48
pH ISM Qualification Kit Instruction manual Bedienungsanleitung Instructions d’utilisation 1258 pH ISM Qualification Kit 52 300 439

Transcript of pH ISM Qualification Kit Instruction manual ... ISM Qualification Kit Instruction manual...

pH ISM Qualification Kit

Instruction manualBedienungsanleitungInstructions d’utilisation

1258pH ISM Qualification Kit52 300 439

2 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

English Page 3

Deutsch Seite 17

Français Page 33

pH ISM Qualification Kit 3

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit

Instruction manualBedienungsanleitungInstructions d’utilisation

4 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

1 Safety........................................................................................51.1 Use in the Ex-zones:.........................................................61.2 Ex-Classification ATEX ......................................................71.2.1 Introduction .....................................................................71.2.2 Rated data ......................................................................71.2.3 Special Conditions ...........................................................8

2 Product Description ....................................................................9

3 Operation.................................................................................103.1 Connecting the transmitter to the pH ISM Qualification Kit....10

4 Product Specification................................................................124.1 Simulator, Pre-registered Values.......................................124.2 Sensor Wear Data ..........................................................124.3 Warnings and Alarms.....................................................13

5 Installation ..............................................................................145.1 Dimensions...................................................................14

6 Ordering Information ................................................................15

7 Protocol...................................................................................16

Contents

Page

pH ISM Qualification Kit 5

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

1 Safety

This instruction manual lists the main points of how to use the pH ISM Qualification Kit from METTLER TOLEDO for best results andin the intended manner.

This instruction manual, and the safety requirements in particular,must be observed by the operator and all other persons workingwith this equipment.

The instruction manual must always be stored close at hand, in aplace accessible to all people working with an ISM pH sensor andthe pH ISM Qualification Kit.

Warning notices and symbols

This instruction manual identifies safety instructions and additionalinformation by means of the following symbols:

This symbol draws attention to safety instructions and warnings ofpotential danger which, if neglected, could result in injury to per-sons and/or damage to property.

This symbol identifies additional information and instructionswhich, if neglected, could lead to defects, inefficient operation andpossible loss of product.

6 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

Intended use

The pH ISM Qualification Kit is intended solely for validating andtesting of the ISM transmitter family, respectively, as described inthis instruction manual.

The pH ISM Qualification Kit is intended for simulating the functions of METTLER TOLEDO ISM sensors, as described in this instructionmanual.

Any other use, or use not mentioned here, that is incompatible withthe technical specifications is deemed inappropriate. The operator issolely responsible for any damage arising from such use.

Other prerequisites for appropriate use include:– observing the instructions, notes and requirements set out in thisinstruction manual

– correct care and maintenance of the unit, according to the in-struction manual

– observing the prescribed environmental and operational conditions – compliance with local statutes

1.1 Use in the Ex-zonesAttention!For an installation in Ex-Zones please read the guidelines followinghereafter:

Ex-classification ATEX:

Ex ia IIC T6/T5/T4/T3 Ga/Gb

Marking and number of the rest certificate:SEV 14 ATEX 0168 X and IECEx SEV 14.0025X

pH ISM Qualification Kit 7

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

1.2 Ex-Classification ATEX

1.2.1 Introduction

According to Directive 94/9/EC (ATEX 95) Appendix I, the pH ISMsensor plug-in heads in the pH ISM Qualification Kit are devices ofequipment group II; category 1/2G which, according to Directive99/92/EC (ATEX 137) can be used in zones 0/1 or 1/2 or 1 or 2 aswell as gas groups IIA, IIB and IIC which are potentially explosivedue to combustible substances in temperature classes T3 to T6.

The requirements specified in EN 60079-14 must be observed dur-ing use / installation.

The pH ISM sensor plug-in head is connected to and operated by atwo-wire cable to the certified transmitter.

The intrinsically safe circuits are galvanically isolated from the non-intrinsically safe circuits up to a norminal voltage peak value of375 V and from the earthed parts up to a norminal voltage peak val-ue of 30 V.

1.2.2 Rated data

Digital pH ISM sensor plug-in head:Type of protection: rated intrinsically safe to Ex ia IIC

Temperature measuring circuit and data chip circuit:Only to be connected to a certified and intrinsically safe power cir-cuit.

Maximum values:Ui ≤�16 V, Ii ≤�30 mA, Pi ≤�50 mWLi = negligibleCi = negligible

In each case, the above values shall represent the sum of the indi-vidual circuits in the intrinsically safe power supply and evaluationdevice concerned (transmitter).

8 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

1.2.3 Special Conditions

– The relationship between the maximum permissible ambient ormedia temperature and temperature class is shown in the follow-ing table.

– With digital pH ISM sensor plug-in heads:

Temperature class Max. ambient ormedia temperature

T 6 62 °CT 5 74 °CT 4 102 °CT 3 154 °C

– The capacitance and inductance of the connection cable has tobe considered.

– The pH ISM sensor plug-in heads can be used in / with the fittingsInFit 76*-**** or InTrac 7**-***, or in / with other suitable fittingsin potentially explosive areas.

– The independent fitting used for installation of the pH ISM sensorplug-in heads must be conductively connected to the equipoten-tial bonding system.

pH ISM Qualification Kit 9

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

2 Product Description

The pH ISM Qualification Kit is a set of 5 different sensor plug-inheads and allows the simulation of reading values of pH ISM sen-sors with predefined values and errors (not changeable by the user)to assure safe use as qualification tool.

Each sensor plug-in head corresponds to one of METTLER TOLEDO’spH ISM sensors and delivers the complete data of an ISM sensor.

The pH ISM Qualification Kit has basically 2 functions: – Tool for the qualification of measuring systems.– Service tool for quick checks and loop trouble-shooting.

The data indicated (primary/secondary) and transmitted are as follow:– Main measured value– Temperature– Error message according to indication.

All standard process and wear data of the sensor are also availablein each plug-in head and are also sent to the transmitter or the PLCas well as to the iSense software.

10 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

3 Operation

3.1 Connecting the transmitter to the pH ISMQualification Kit

To qualify your measuring systems proceed as follows:

Please refer to the transmitter instruction manual for the exact de-scription of the transmitter operation.

Step 1: Disconnect the ISM sensor from the measuring point.

Step 2: Connect one of the pH ISM Qualification Kit plug-in headsto the transmitter via the standard connecting cable.

Step 3: The preregistered values then are displayed on the trans-mitter.

Step 4: Check if the displayed values by the transmitter or the PLCcorrespond to the predefined fixed values of the pH ISMQualification Kit plug-in head.

See certification for exact values and tolerances.

Step 5: In case you are using the Error simulators, check that theappropriate errors are correctly displayed by the transmitteror the PLC.

Step 6: Report results into the attached spreadsheet “Protocol for pHISM Qualification Kit”.

Problem solving: If any of the tests described above failed, youshould change the connecting cable and repeat the test. If the teststill shows the same result, the transmitter or the cable is defective.If you are using a transmitter with current outputs, so ensure the out-puts are correctly wired.

You must never do a calibration (the simulators are read-only).

You must never increment autoclave cycles (always set “NO” to cy-cle counter), this is only needed if autoclave has been set to a valuehigher than 0.

pH ISM Qualification Kit 11

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

Different transmitters may display different values and errors.

Out of range behavior is also different depending on the transmitterin use thus different values/readings may occur.

Set the transmitter input filter to off (only for SIM pH TGL).

Do not use the pH ISM plug-in heads after the expiry date shownon the label of each plug-in head. Please send them back to METTLER TOLEDO for recertification.

Environment operating and storing conditions:

Permissible ambient temperature (operation): –25°C to 60°C (–13°F to 140°F)

Permissible ambient temperature (storage/transport):–25°C to 60°C (–13°F to 140°F)

Connecting pH ISM Qualifying plug-in head

Measuring point withMETTLER TOLEDO Electrode

4 Product Specification

4.1 Simulator, Pre-registered ValuesOrder No. Product Legend pH Value Temp.

Designation

SIM pH Kit Order No. 52 300 410

52 300 411 SIM PH4 SIM PH4 pH 4.00 80°C

52 300 412 SIM PH7 SIM PH7 pH 7.00 25°C

52 300 413 SIM PH TGL Toggle Mode 30 sec pH 4.00 80°C& pH 7.00 & 25°C

52 300 414 SIM PH ERR1 Glass Breakage pH 7.00 25°C

52 300 415 SIM PH ERR2 Fail Temperature Range pH 10.67 –28°C

4.2 Sensor Wear DataSensor Wear Monitor pH Transmitters M400/M420/M700/M800

Time to Maintenance (TTM) 20 d

Life Time Indicator (DLI) 245 d

Adaptive Cal Timer (ACT) 7 d

Sensor operating time 55 d

Autoclaving cycles 1

CIP cycles 7

SIP cycles 3

Max temperature 130°C dd.mm.yyyy (date of production)

Exceptions

52 300 414 (SIM pH ERR1) TTM = 0 d / DLI = 0 d / ACT = 0 d

52 300 415 (SIM pH ERR2) TTM = 0 d / DLI = 0 d / ACT = 0 d

12 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

pH ISM Qualification Kit 13

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

4.3 Warnings and Alarms

52 300 414 (SIM pH ERR1) Incident: Glass�breakage

Transmitter Warnings /AlarmsM300� Error�pH�Gls�Res�<5MΩ

M400 Error�pH�Gls�Res�<5MΩ

M420 Error�pH�Gls�Res�<5M�(Err�15)

M700 Fail�Glass�impedance

Warn�Cal�timer

Warn�TTM�Maintenance�timer

M800 Error�pH�Gls�Res�<5MΩ

Maint�Required

Cal�Required

Change�Sensor

52 300 415 (SIM pH ERR2) Incident: Temperature�range�failure

Transmitter Warnings /AlarmsM300 Error�pH�Gls�change�<0.3

M400 Error�pH�Gls�change�<0.3

M420 Error pH Gls change <0.3 (Err 13)

M700 Fail Temperature Range

Fail pH Range

Warn Cal timer

Warn TTM Maintenance timer

M800 Warning pH Gls change <0.3

Maint Required

Cal Required

Change Sensor

Please refer to your transmitter instruction manual for specific instructions.

14 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

5 Installation

5.1 Dimensions

Markings

The markings labeled on each pH ISM plug-in head state the fol-lowing information:

0006

6736

64.5

mm

2.54

"

[ 15.9 mm0.63"

pH ISM Qualification Kit 15

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

6 Ordering Information

Order No. Designation52 300 410 SIM pH Kit52 300 411 SIM pH452 300 412 SIM pH752 300 413 SIM pH TGL52 300 414 SIM pH ERR152 300 415 SIM pH ERR2

52 300 416 SIM O2 Kit52 300 417 SIM O2 ZERO52 300 418 SIM O2 AIR52 300 419 SIM O2 TGL52 300 420 SIM O2 ERR152 300 421 SIM O2 ERR2

52 300 422 SIM O2 ppb Kit52 300 423 SIM O2 ppb ZERO52 300 424 SIM O2 ppb AIR52 300 425 SIM O2 ppb TGL52 300 426 SIM O2 ppb ERR152 300 427 SIM O2 ppb ERR2

52 300 428 SIM O2 Trace Kit52 300 429 SIM O2 Trace ZERO52 300 430 SIM O2 Trace AIR52 300 431 SIM O2 Trace TGL52 300 432 SIM O2 Trace ERR152 300 433 SIM O2 Trace ERR2The single simulators are not available for sale.

16 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

7 Protocol

A copy of this form in A4 format is delivered with the pH ISM Quali-fication Kit.

Protocol for pH ISM Qualification Kit © Mettler-Toledo AG, MarCom, Im Hackacker 15, CH - 19002/30 .frodrU 2098

Protocol for pH ISM Qualification Kit

Facility Name

Instrument Manufacturer

Date of Purchase

Transmitter Model

Transmitter Serial Nr

Simulator Simulator Designation Valid Parameter/s (check all that apply for)tnemurtsni sihtlitnuN/SN/P

Date / Time Acceptable? Acceptable? Name /SignatureYes No

pH ISM Qualification Kit 17

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualifizierkit

BedienungsanleitungBedienungsanleitungInstructions d’utilisation

18 pH ISM Qualification Kit

pH ISM Qualification Kit © 12/14 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

18 pH ISM Qualification Kit

1 Sicherheit ................................................................................191.1 Einsatz in Ex-Zonen:.......................................................201.2 Ex-Klassifikation ATEX ....................................................211.2.1 Einleitung......................................................................211.2.2 Nenndaten ....................................................................211.2.3 Besondere Bedingungen .................................................22

2 Produktbeschreibung ................................................................23

3 Betrieb ....................................................................................243.1 Anschluss des Transmitters an das pH ISM Qualifizierkit ....24

4 Produktspezifikationen .............................................................274.1 Simulator, vorgegebene Werte .........................................274.2 Daten Elektrodenverschleiss ............................................274.3 Warnungen und Alarme ..................................................28

5 Installation ..............................................................................295.1 Abmessungen ...............................................................29

6 Bestellinformationen ................................................................30

7 Protokoll..................................................................................31

Inhaltsverzeichnis

Seite

pH ISM Qualification Kit 19

© 12/14 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 19

1 SicherheitDiese Bedienungsanleitung beinhaltet alle notwendigen Informatio-nen, um das pH ISM Qualifizierkit von METTLER TOLEDO sicher,sachgerecht und bestimmungsgemäss anzuwenden.

Diese Bedienungsanleitung und im speziellen die Sicherheitshin-weise müssen von allen Personen, die mit diesem Qualifizierkitarbeiten, beachtet und eingehalten werden.

Bitte bewahren Sie diese Bedienungsanleitung an einem sicheren Ortauf, wo sie für Personen, die mit einer pH-Elektrode und dem pH ISMQualifizierkit arbeiten, jederzeit zugänglich ist.

Warnhinweise und Symbole

In dieser Bedienungsanleitung werden Sicherheitshinweise und Zu-satzinformationen durch folgende Piktogramme gekennzeichnet:

Dieses Piktrogramm kennzeichnet Sicherheits- und Gefahrenhin-weise, deren Missachtung zu Personen- und/oder Sachschädenführen können.

Dieses Piktogramm kennzeichnet Zusatzinformationen und Anwei-sungen deren Missachtung zu Defekten, ineffizientem Betrieb oderzum Ausfall der Produktion führen können.

20 pH ISM Qualification Kit

pH ISM Qualification Kit © 12/14 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

20 pH ISM Qualification Kit

Bestimmungsgemässe Verwendung

Das pH ISM Qualifizierkit ist ausschliesslich zur Validierung undÜberprüfung von ISM-fähigen Transmittern gemäss den in dieserBedienungsanleitung beschriebenen Angaben vorgesehen.

Das pH ISM Qualifizierkit dient der Simulation der Funktionen einerMETTLER TOLEDO ISM-Elektrodewie in dieser Bedienungsanleitungbeschrieben.

Jede andere oder darüber hinausgehende Benutzung, sowie jede An-wendung, welche nicht den technischen Spezifikationen entspricht,gilt als nicht bestimmungsgemäss. Für allfällige Schäden, welcheauf eine solche Verwendung zurückzuführen sind, trägt der Betreiberdas alleinige Risiko.

Zur bestimmungsgemässen Verwendung gehören ausserdem:– die Beachtung der Anweisungen, Vorschriften und Hinweise in dervorliegenden Bedienungsanleitung,

– die korrekte Instandhaltung und Pflege der Einheit wie in der Bedienungsanleitung beschrieben,

– der Betrieb unter Beachtung der vorgeschriebenen Umwelt- und Betriebsbedingungen,

– die Einhaltung der lokalen Gesetzgebung.

1.1 Einsatz in Ex-ZonenAchtung!Lesen Sie im Hinblick auf die Installation in Ex-Zonen die folgendenLeitlinien:

Ex-Klassifikation ATEX:

Ex ia IIC T6/T5/T4/T3 Ga/Gb

Kennzeichnung und Nummer des Testzertifikats:SEV 14 ATEX 0168 X and IECEx SEV 14.0025X

pH ISM Qualification Kit 21

© 12/14 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 21

1.2 Ex-Klassifikation ATEX

1.2.1 Einleitung

Gemäß Anhang I der Richtlinie 94/9/EG (ATEX 95) handelt es sichbei den pH-ISM-Sensorsteckköpfen im pH-ISM-Qualifizierungskit umGeräte der Prüfmittelgruppe II, Kategorie 1/2G, die, in Übereinstim-mung mit Richtlinie 99/92/EG (ATEX 137) in den Zonen 0/1 bzw.1/2 bzw. 1 oder 2 sowie in den Gasgruppen IIA, IIB und IIC einge-setzt werden können, die potenziell explosiv sind aufgrund vonbrennbaren Stoffen in den Temperaturklassen T3 bis T6.

Die Anforderungen aus EN 60079-14 müssen beim Einsatz/bei derInstallation beachtet werden.

Der pH-ISM-Sensorsteckkopf wird über ein zweiadriges Kabel an dengesondert bescheinigten Transmitter angeschlossen und betrieben.

Die eigensicheren Kreise sind von den nicht eigensicheren Kreisenbis zu einem Spitzensollwert der Spannung von 375 V und von den geerdeten Teilen bis zu einem Spitzensollwert der Spannung von 30 V galvanisch isoliert.

1.2.2 Nenndaten

Digitaler pH ISM-Sensorsteckkopf:Zündschutzart: eingestuft als eigensicher bis Ex ia IIC

Temperaturmesskreis und Datenchipkreis:Darf nur an bescheinigte und eigensichere Leistungskreise ange-schlossen werden

Höchstwerte:Ui ≤�16 V, Ii ≤�30 mA, Pi ≤�50 mWLi = vernachlässigbarCi = vernachlässigbar

In jedem Fall beziehen sich obige Werte auf die Summe der indivi-duellen Kreise in der eigensicheren Stromversorgung und imentsprechenden Auswertegerät (Transmitter).

22 pH ISM Qualification Kit

pH ISM Qualification Kit © 12/14 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

22 pH ISM Qualification Kit

1.2.3 Besondere Bedingungen

– Folgende Tabelle enthält das Verhältnis zwischen der maximal zulässigen Umgebungs- bzw. Mediumstemperatur und der Temperaturklasse.

– Mit digitalen pH ISM-Sensorsteckköpfen:

Temperaturklasse Max. Umgebungs- oderMediumstemperatur

T 6 62 °CT 5 74 °CT 4 102 °CT 3 154 °C

– Die Kapazität und die Induktivität des Verbindungskabels sind zubeachten.

– Die pH ISM-Sensorsteckköpfe können in / mit den Armaturen InFit 76*-*** oder InTrac 7**-*** oder in / mit anderen geeigne-ten Armaturen in potenziell explosionsgefährdeten Bereicheneingesetzt werden.

– Die unabhängige Armatur für die Installation der pH ISM-Sensor-steckköpfe muss leitend mit dem Potenzialausgleichssystemverbunden werden.

pH ISM Qualification Kit 23

© 12/14 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 23

2 Produktbeschreibung

Das pH ISM Qualifizierkit besteht aus 5 verschiedenen Sensor-Steck-köpfen und erlaubt das Simulieren von Lesedaten der ISM pH-Sensoren.Diese Daten und Fehler sind vordefiniert (vom Kunden nicht verän-derbar) und dienen als Werkzeug der Qualifizierung zum sicherenBetrieb.

Jeder Sensorkopf entspricht einem METTLER-TOLEDO pH ISM Sensorund liefert die kompletten Daten eines ISM-Sensors.

Das pH ISM Qualifizierkit bietet zwei Hauptfunktionen: – es dient als Werkzeug zur Qualifizierung eines Messsystems– es dient als Servicegerät für die rasche Überprüfung und Fehler -suche innerhalb eines gesamten Messloops.

Folgende Daten (primäre/sekundäre) werden angezeigt und über-tragen:– Hauptmesswert– Temperatur– Fehlermeldung entsprechend der Indikation

Alle ISM-Standard Prozess- und Verschleissdaten des Sensors sindin jedem Sensorkopf gespeichert und werden sowohl an Transmit-ter, Prozessleitsysteme und die iSense Software übertragen.

24 pH ISM Qualification Kit

pH ISM Qualification Kit © 12/14 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

24 pH ISM Qualification Kit

3 Betrieb

3.1 Anschluss des Transmitters an das pH ISMQualifizierkit

Um Ihr ISM-Messsystem zu überprüfen gehen Sie wie folgt vor:

Für die genaue Beschreibung des Transmitterbetriebes verweisen wirSie auf die Betriebsanleitung des jeweiligen Transmitters.

Schritt 1 : ISM-Sensor von der Messstelle trennen.

Schritt 2 : Einen der Sensorköpfe des pH ISM Qualifizierkits mittelsvorhandenem Verbindungskabel an den Transmitter an-schliessen.

Schritt 3 : Die vordefinierten Werte werden am Transmitter angezeigt.

Schritt 4 : Überprüfen, ob die angezeigten Werte am Transmitteroder dem Prozessleitsystem mit den vordefinierten Werten des Sensorkopfs aus dem pH ISM Qualifizierkitübereinstimmen.

Beachten Sie das Zertifikat für die exakten Werte undToleranzen.

Schritt 5 : Bei der Verwendung der Fehlersimulatoren ist darauf zuachten, dass am Transmitter bzw. dem Prozessleitsystemdie entsprechenden Fehler korrekt angezeigt werden.

Schritt 6 : Eintragen der Resultate in das mitgelieferte Qualifizie-rungs-Formular «Protokoll pH ISM Qualifizierkit».

Problemlösung: Wenn einer der beschriebenen Tests nicht erfolg-reich bestanden wurde, prüfen Sie das Verbindungskabel zwischenSimulator und Transmitter und tauschen es allenfalls aus. Sollte derTest danach erneut negativ ausfallen, ist der Transmitter defekt. BeiVerwendung eines Transmitters mit Stromausgang überprüfen Sie, obdie Anschlüsse richtig belegt wurden.

pH ISM Qualification Kit 25

© 12/14 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 25

Führen Sie mit den Simulatoren niemals eine Kalibrierung durch.(Die Simulatoren sind nur Leseeinheiten.)

Erhöhen Sie niemals manuell den Autoklavier-Zähler (Setzen Sieden Zähler immer auf «Nein»). Dies ist nur nötig, wenn der Autokla-vier-Wert grösser als 0 ist.

Verschiedene Transmitter können unterschiedliche Werte undFehlermeldungen anzeigen.

Messwertüberschreitungen werden von verschiedenen Transmitternunterschiedlich behandelt und können entsprechend andere Werteund Anzeigen zur Folge haben.

Schalten Sie den Transmitter Eingangsfilter aus (nur für SIM pH TGL).

Verwenden Sie die pH ISM Sensorköpfe nicht über das aufge-druckte Verfallsdatum hinaus. Zur Rekalibrierung senden Sie bittedas komplette Kit an METTLER TOLEDO zurück.

26 pH ISM Qualification Kit

pH ISM Qualification Kit © 12/14 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

26 pH ISM Qualification Kit

Betriebs- und Lagerbedingungen:

Zulässige Umgebungstemperatur (Betrieb): –25°C bis 60°C

Zulässige Umgebungstemperatur (Lagerung/Transport):–25°C bis 60°C

Zur Qualifizierung ange-schlossener ISM-Sensorkopf

Messpunkt mitMETTLER TOLEDO Elektrode

pH ISM Qualification Kit 27

© 12/14 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 27

4 Produktspezifikationen

4.1 Simulator, vorgegebene WerteBestell-Nr. Produkt- Legende pH-Wert Temp.

beschreibung

SIM pH Kit Bestell-Nr. 52 300 410

52 300 411 SIM PH4 SIM PH4 pH 4.00 80°C

52 300 412 SIM PH7 SIM PH7 pH 7.00 25°C

52 300 413 SIM PH TGL Umschaltmodus 30 Sek. pH 4.00 80°C& pH 7.00 & 25°C

52 300 414 SIM PH ERR1 Glasbruch pH 7.00 25°C

52 300 415 SIM PH ERR2 Fehler Temperaturbereich pH 10.67 –28°C

4.2 Daten ElektrodenverschleissÜberwachung Transmitter M400/M420/M700/M800pH-Elektrodenverschleiss

Zeit bis Wartungsintervall (TTM) 20 d

Lebenszeit Indikator (DLI) 245 d

Adaptiver Kalibriertimer (ACT) 7 d

Sensor-Betriebszeit 55 d

Autoklavier-Zyklen 1

CIP-Zyklen 7

SIP-Zyklen 3

Max. Temperatur 130°C tt.mm.jjjj (Produktionsdatum)

Ausnahmen

52 300 414 (SIM pH ERR1) TTM = 0 d / DLI = 0 d / ACT = 0 d

52 300 415 (SIM pH ERR2) TTM = 0 d / DLI = 0 d / ACT = 0 d

28 pH ISM Qualification Kit

pH ISM Qualification Kit © 12/14 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

28 pH ISM Qualification Kit

4.3 Warnungen und Alarme

52 300 414 (SIM pH ERR1) Ereignis: Glasbruch

Transmitter Warnungen/AlarmeM300� Warn.�pH�Gls�<5MΩ

M400 Warn.�pH�Gls�<5MΩ

M420 Warn.�pH�Gls�<5M�(Err�15)

M700 Ausf.�Glasimpedanz

Warn.�Kalibriertimer

Warn.�TTM�Wartungstimer

M800 Fehler�pH�Gls�R<5�MΩ

Wartung�erforderlich

Justierung�erforderlich

Sensor�austauschen

52 300 415 (SIM pH ERR2) Ereignis: Fehler�Temperaturbereich

Transmitter Warnungen/AlarmeM300 Warn.�pH�Gls�Änd.<0.3

M400 Warn.�pH�Gls�Änd.<0.3

M420 Warn. pH Gls Änd.<0.3 (Err 13)

M700 Ausf. pH Messbereich

Ausf. Temperaturmessbereich

Warn. Kalibriertimer

Warn. TTM Wartungstimer

M800 Warn. pH Gls Änd. <0.3

Wartung erforderlich

Justierung erforderlich

Sensor austauschen

Für spezifische Anweisungen verweisen wir Sie auf die Betriebsan-leitung Ihres Transmitters.

pH ISM Qualification Kit 29

© 12/14 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 29

5 Installation

5.1 Abmessungen

Beschriftung

Die Etikette, die sich auf jedem ISM pH-Sensorkopf befindet, enthältfolgende Informationen:

0006

6736

64.5

mm

2.54

"

[ 15.9 mm0.63"

30 pH ISM Qualification Kit

pH ISM Qualification Kit © 12/14 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

30 pH ISM Qualification Kit

6 Bestellinformationen

Bestell-Nr. Bezeichnung52 300 410 SIM pH Kit52 300 411 SIM pH452 300 412 SIM pH752 300 413 SIM pH TGL52 300 414 SIM pH ERR152 300 415 SIM pH ERR2

52 300 416 SIM O2 Kit52 300 417 SIM O2 ZERO52 300 418 SIM O2 AIR52 300 419 SIM O2 TGL52 300 420 SIM O2 ERR152 300 421 SIM O2 ERR2

52 300 422 SIM O2 ppb Kit52 300 423 SIM O2 ppb ZERO52 300 424 SIM O2 ppb AIR52 300 425 SIM O2 ppb TGL52 300 426 SIM O2 ppb ERR152 300 427 SIM O2 ppb ERR2

52 300 428 SIM O2 Trace Kit52 300 429 SIM O2 Trace ZERO52 300 430 SIM O2 Trace AIR52 300 431 SIM O2 Trace TGL52 300 432 SIM O2 Trace ERR152 300 433 SIM O2 Trace ERR2Simulatoren können nicht einzeln gekauft werden.

pH ISM Qualification Kit 31

© 12/14 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 31

7 Protokoll

Eine Kopie dieses Formulars im A4-Format wird mit dem pH ISMQualifizierkit mitgeliefert.

Protokoll für pH ISM Qualifizierkit © Mettler-Toledo AG, MarCom, Im Hackacker 15, CH -8902 Urdorf. 03 /2009 1

Protokoll für pH ISM Qualifizierkit

Name der Produktionsstätte

Gerätehersteller

Kaufdatum

Transmittermodell

Serienummer des Transmitters

Simulator Simulator Bezeichnung Gültig bis Parameter (alle überprüfen, die diesesArtikelnr. Serienr. Gerät betreffen)

Datum /Zeit Akeptiert? Akzeptiert? Name /UnterschriftJa Nein

32 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

32 pH ISM Qualification Kit

Notizen

pH ISM Qualification Kit 33

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 33

Set de qualification ISM pH

Instructions d’utilisationBedienungsanleitungInstructions d’utilisation

34 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

34 pH ISM Qualification Kit

1 Sécurité...................................................................................351.1 Utilisation dans les zones classées Ex :............................361.2 Classification Ex ATEX ....................................................371.2.1 Introduction ...................................................................371.2.2 Données nominales .......................................................371.2.3 Conditions spéciales ......................................................38

2 Description du produit ..............................................................39

3 Exploitation .............................................................................403.1 Connecter le transmetteur

au simulateur de qualification ISM pH ..............................40

4 Caractéristique du produit ........................................................434.1 Simulateur, valeurs pré-enregistrées .................................434.2 Données d’usure de l’électrode ........................................434.3 Mises en garde et alarmes ..............................................44

5 Installation ..............................................................................455.1 Dimensions ..................................................................45

6 Informations pour la commande................................................46

7 Protocole .................................................................................47

Table des matières

Page

pH ISM Qualification Kit 35

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 35

1 SécuritéCe manuel d’instructions décrit les points principaux de l’utilisationdu Kit de qualification ISM pH de METTLER TOLEDO pour usage optimal et selon l’emploi prévu.

Les instructions de ce manuel, et particulièrement les consignes desécurité, doivent être respectées par l’opérateur et toute autrepersonne travaillant avec ce matériel.

Ce manuel d’instructions doit toujours être conservé à portée de maindans un endroit accessible aux personnes travaillant avec une sonde pH et avec le kit de qualification ISM pH.

Mise en garde et symboles

Les présentes instructions d’utilisation utilise les symboles suivantspour désigner les consignes de sécurité :

Ce symbole a pour but d’attirer l’attention sur les consignes de sécurité et avertissement relatifs à des dangers potentiels qui,s’ils ne sont pas pris en considération, pourraient être à l’origine deblessures et/ou de dommages.

Ce symbole signale des informations ou instructions complémen-taires qui, si elles ne sont pas prises en compte, pourraientoccasionner des défauts, un fonctionnement inefficace ou une éven-tuelle diminution de la production.

36 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

36 pH ISM Qualification Kit

Utilisation conforme aux prescriptions

Le kit de qualification ISM pH est destiné uniquement pour la vali-dation et le contrôle des transmetteurs de la famille ISM,respectivement, comme décrit dans le reste de ce manuel.

Le kit de qualification ISM pH est destiné à simuler les fonctions desélectrodes de mesures ISM de METTLER TOLEDO, comme décritdans le manuel d’utilisation.

Toute autre utilisation que mentionnée ou qui ne correspond pas auxcaractéristiques techniques du support rétractable est considéréecomme inadéquate. L’exploitant est entièrement responsable de toutdommage résultant d’une utilisation inadéquate.

Font partie d’une utilisation adéquate :– le respect des indications, prescriptions et consignes des présentesinstructions d’utilisation,

– l’entretien correct des simulateurs ISM,– l’observation des intervalles d’inspection et de maintenance pres-crits,

– le respect de la législation locale.

1.1 Utilisation dans les zones classées ExAttention !Pour toute installation dans les zones classées Ex, veuillez lire lesconsignes suivantes :

Classification Ex ATEX :

Ex ia IIC T6/T5/T4/T3 Ga/Gb

Marquage et numéro du certificat de vérification :SEV 14 ATEX 0168 X and IECEx SEV 14.0025X

pH ISM Qualification Kit 37

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 37

1.2 Classification Ex ATEX

1.2.1 Introduction

Conformément à la directive 94/9/CE (ATEX 95), Annexe I, les têtesde raccordement des électrodes de pH (ISM) reprises dans le set dequalification ISM pH, appartiennent au groupe d’appareils II, caté-gorie 1/2G qui, conformément à la directive 99/92/CE (ATEX 137),peuvent être utilisés dans les zones 0/1, 1/2, 1 ou 2, ainsi que dansles groupes de gaz IIA, IIB et IIC qui sont potentiellement explosifsen présence de matériaux combustibles dans la plage de tempéra-ture des classes T3 à T6.

Les exigences de la norme européenne EN 60079-14 doivent êtrerespectées lors de l’utilisation / installation.

La tête de raccordement de l’électrode de pH (ISM) est raccordée àun câble à deux fils connecté au transmetteur homologué, qui per-met de l’actionner.

Les circuits de sécurité intrinsèque sont isolés galvaniquement descircuits de sécurité non intrinsèque jusqu’à une valeur de crête de latension nominale de 375 V. Ils sont également isolés galvanique-ment des installations mises à la terre jusqu’à une valeur de crêtede la tension nominale de 30 V.

1.2.2 Données nominales

Tête de raccordement de l’électrode de pH numérique (ISM) :Type de protection : sécurité intrinsèque conformément à Ex ia IIC

Circuit de mesure de la température et circuit de la puce dedonnées :Uniquement pour le raccordement à un circuit électrique de sécuritéintrinsèque homologué

Valeurs maximales :Ui ≤�16 V, Ii ≤�30 mA, Pi ≤�50 mWLi = négligeableCi = négligeable

38 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

38 pH ISM Qualification Kit

Dans chaque cas, les valeurs ci-dessus représentent la somme descircuits individuels de l’alimentation à sécurité intrinsèque associéeet de l’appareil de contrôle correspondant (transmetteur).

1.2.3 Conditions spéciales

– Le lien entre la température du milieu/ambiante maximale autori-sée et la classe de températures est indiqué dans le tableausuivant.

– Têtes de raccordement de l’électrode de pH numérique (ISM) :

Classe de températures Température ambiante max. outempérature du milieu max.

T 6 62 °CT 5 74 °CT 4 102 °CT 3 154 °C

– La capacitance et l’inductance du câble raccordé doivent êtreprises en compte.

– Les têtes de raccordement des électrodes de pH (ISM) peuvent êtrefixées sur des supports InFit 76*-**** ou InTrac 7**-*** ou surd’autres supports adaptés aux zones potentiellement explosives.

- Le raccord indépendant utilisé pour l’installation des têtes de rac-cordement des électrodes de pH (ISM) doit être raccordé de façonconductrice au système de liaison équipotentielle.

pH ISM Qualification Kit 39

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 39

2 Description du produit

Le kit de qualification ISM pH est un set de 5 connecteurs différentsqui permettent de simuler pour les électrodes de mesure suivantesdes valeurs prédéterminées et des conditions d’erreur (non modi-fiables par l’utilisateur) afin d’assurer une utilisation sûre de cet kitde qualification.

Chaque connecteur du kit correspond à l’une des électrodes de me-sure ISM pH de METTLER TOLEDO et délivre toutes les données ISMnormalement générées par une électrode ISM.

Le kit de qualification ISM pH a essentiellement 2 fonctions : – Outil de qualification des chaînes de mesure ISM– Outil de service pour contrôles rapides et détection d’erreurs

Les données incluses (primaires et secondaires) et transmises sontles suivantes:– Valeur de mesure principale– Température– Message d’erreur d’après liste

Toutes les données ISM standard comme l’usure sont disponiblesdans chaque simulateur et sont également transmises au poste demesure ainsi qu’à l’outil de maintenance iSense.

40 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

40 pH ISM Qualification Kit

3 Exploitation

3.1 Connecter le transmetteur au simulateur dequalification ISM pH

Pour qualifier votre système de mesure ISM veuillez procéder com-me suit :

Veuillez vous référer au manuel d’instructions du transmetteur pourune description exacte de l’utilisation du transmetteur.

Etape 1 : déconnecter l’électrode ISM du point de mesure

Etape 2 : connecter l’un de simulateurs ISM au transmetteur en uti-lisant le câble de connexion déjà installé

Etape 3 : les valeurs prédéfinies sont affichées sur le transmetteur

Etape 4 : vérifier que les valeurs présentes sur l’affichage du trans-metteur ou du système de contrôle correspondent auxvaleurs prédéfinies comme stipulé sur le certificat pourchaque simulateur.

Considérez le certificat pour les valeurs exactes etles tolerances.

Etape 5 : Pour le cas où vous utilisez les simulateurs de conditiond’erreur, vérifier que les erreurs simulées soient égalementaffichées sur le transmetteur ou dans le système decontrôle.

Etape 6 : Entrer les valeurs dans le formulaire également fourni «Protocole pour set de qualification ISM pH».

Dépannage: Si l’un des tests susmentionnés n’est pas passé avecsuccès, contrôle ou échanger le câble de connexion entre le simu-lateur et le transmetteur. Si le test reste négatif, le transmetteurcontient un défaut. Si vous utilisez un transmetteur avec sorties decourant, assurez vous que les sorties sont configurées correctement.

Ne jamais effectuer de calibration (les simulateurs sont en moderead-only).

Ne jamais incrémenter manuellement le compteur de cycles d’au-toclavage (toujours quitter le message par «non»). Cette opérationest nécessaire seulement si le compteur d’autoclavages a une va-leur différente de 0.

Des transmetteurs différents peuvent afficher des valeurs légè-rement différentes.

En cas de simulation d’erreurs, le comportement aux erreurs dechaque transmetteur est différent d’après le modèle et en consé-quence d’autres valeurs et / ou messages d’erreur peuventapparaître.

Éteindre le filtre d’entrée du transmetteur (seulement pour SIM pHTGL).

Ne pas utiliser les simulateurs après la date de péremption indi-quée sur chaque simulateur. Veuillez renvoyer le kit complet pourrecalibration à votre représentant METTLER TOLEDO.

pH ISM Qualification Kit 41

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 41

42 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

42 pH ISM Qualification Kit

Conditions d’utilisation et entreposage:

Température ambiente admissible (opération): –25°C à 60°C

Température ambiente admissible (entreposage/transport):–25°C à 60°C

Simulateur ISM pHconnecté

Point de mesure avecélectrode METTLER TOLEDO

pH ISM Qualification Kit 43

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 43

4 Caractéristique du produit

4.1 Simulateur, valeurs pré-enregistréesNo. de Désignation Légende Valeur pH Temp.commande produit

SIM pH Kit No. de commande 52 300 410

52 300 411 SIM PH4 SIM PH4 pH 4.00 80°C

52 300 412 SIM PH7 SIM PH7 pH 7.00 25°C

52 300 413 SIM PH TGL Toggle Mode 30 sec pH 4.00 80°C& pH 7.00 & 25°C

52 300 414 SIM PH ERR1 Rupture du verre pH 7.00 25°C

52 300 415 SIM PH ERR2 Erreur plage de température pH 10.67 –28°C

4.2 Données d’usure de l’électrodeIndicateur d’usure pH Transmetteurs M400/M420/M700/M800

Délai de maintenance (TTM) 20 d

Moniteur DLI 245 d

Minuterie de Cal adaptatif (ACT) 7 d

Durée de service électrode 55 d

Cycles d’autoclavage 1

Cycles NEP 7

Cycles SEP 3

Température max. 130°C dd.mm.yyyy (date de production)

Exceptions

52 300 414 (SIM pH ERR1) TTM = 0 d / DLI = 0 d / ACT = 0 d

52 300 415 (SIM pH ERR2) TTM = 0 d / DLI = 0 d / ACT = 0 d

44 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

44 pH ISM Qualification Kit

4.3 Mises en garde et alarmes

52 300 414 (SIM pH ERR1) Accident: Rupture�du�verre

Transmetteur Mises en garde/alarmesM300� Erreur�Res�Verre�<5MΩ

M400 Erreur�Res�Verre�<5MΩ

M420 Erreur�Res�Verre�<5M�(Err�15)

M700 Défa.�Impédance�él.�Verre

Aver.�Minuteur�calibrage

Aver.�TTM�Minuteur�d’entretien

M800 Erreur�R�verre�pH�<5MΩ

Maintenance�néc.

Cal.�néc.

Chang.�capteur

52 300 415 (SIM pH ERR2) Accident: Erreur�plage�de�température

Transmetteur Mises en garde/alarmesM300 Att.�pH�Verre�mod�<0.3

M400 Att.�pH�Verre�mod�<0.3

M420 Att. pH Verre mod <0.3 (Err 13)

M700 Défa Température Plage

Défa pH Plage

Aver. Minuteur calibrage

Aver. TTM Minuteur d’entretien

M800 Att. modif. verre pH <0.3

Maintenance néc.

Cal. néc.

Chang. capteur

S’il vous plaît se référer à votre manuel d’utilisation du transmetteurpour obtenir des instructions spécifiques.

pH ISM Qualification Kit 45

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 45

5 Installation

5.1 Dimensions

Identification

L’autocollant figurant sur chaque simulateur ISM pH fournit les in-formations suivantes :

0006

6736

64.5

mm

2.54

"

[ 15.9 mm0.63"

46 pH ISM Qualification Kit

pH ISM Qualification Kit © 05/15 Mettler-Toledo AG, Greifensee52 300 439 Printed in Switzerland

46 pH ISM Qualification Kit

6 Informations pour la commande

No. de commande Désignation52 300 410 SIM pH Kit52 300 411 SIM pH452 300 412 SIM pH752 300 413 SIM pH TGL52 300 414 SIM pH ERR152 300 415 SIM pH ERR2

52 300 416 SIM O2 Kit52 300 417 SIM O2 ZERO52 300 418 SIM O2 AIR52 300 419 SIM O2 TGL52 300 420 SIM O2 ERR152 300 421 SIM O2 ERR2

52 300 422 SIM O2 ppb Kit52 300 423 SIM O2 ppb ZERO52 300 424 SIM O2 ppb AIR52 300 425 SIM O2 ppb TGL52 300 426 SIM O2 ppb ERR152 300 427 SIM O2 ppb ERR2

52 300 428 SIM O2 Trace Kit52 300 429 SIM O2 Trace ZERO52 300 430 SIM O2 Trace AIR52 300 431 SIM O2 Trace TGL52 300 432 SIM O2 Trace ERR152 300 433 SIM O2 Trace ERR2Les simulateurs seuls ne sont pas disponibles pour la vente.

pH ISM Qualification Kit 47

© 05/15 Mettler-Toledo AG, Greifensee pH ISM Qualification KitPrinted in Switzerland 52 300 439

pH ISM Qualification Kit 47

7 Protocole

Une copie de ce formulaire en format A4 est fournie avec le set dequalification ISM pH.

Protocole pour set de qualification ISM pH © Mettler-Toledo AG, MarCom, Im Hackacker 15, CH -8902 Urdorf. 03 /2009 1

Protocole pour set de qualification ISM pH

Nom site

Fabricant de l’instrument

Date d’achat

Modèle transmetteur

No. série transmetteur

Simulateur Simulateur Désignation Valable Paramètre/s)selbacilppa xuec tuot reifirév(à’uqsujN/SN/P

Date /Heure Acceptable? Acceptable? Nom/SignatureOui Non

A Mettler-Toledo Ges.m.b.H., Südrandstrasse 17, A-1230 Wien, Austria Phone +43 1 604 19 80, Fax +43 1 604 28 80

BR Mettler-Toledo Ind. e Com. Ltda., Avenida Tamboré, 418-Tamboré, BR-06460-000 Barueri /SPPhone +55 11 4166 74 00, Fax +55 11 4166 74 01

CH Mettler-Toledo (Schweiz) GmbH, Im Langacher, Postfach, CH-8606 Greifensee Phone +41 44 944 45 45, Fax +41 44 944 45 10

CN Mettler-Toledo Instruments (Shanghai) Co. Ltd., 589 Gui Ping Road, Cao He Jing, CN-200233 Shanghai, Phone +86 21 64 85 04 35, Fax +86 21 64 85 33 51

D Mettler-Toledo GmbH, Prozeßanalytik, Ockerweg 3, D-35396 Gießen Phone +49 641 507 444, Fax +49 641 507 397

F Mettler-Toledo, Analyse Industrielle S.A.S., 30, Boulevard de Douaumont, F-75017 ParisPhone +33 1 47 37 06 00, Fax +33 1 47 37 46 26

J Mettler-Toledo K.K., Process Division, 6F Ikenohata Nisshoku Bldg., 2-9-7, Ikenohata, Taito-ku, JP-110-0008 Tokyo, Phone +81 3 5815 5606, Fax +81 3 5815 5626

UK Mettler-Toledo LTD, 64 Boston Road Beaumont Leys, GB-Leicester LE4 1AW Phone +44 116 235 7070, Fax +44 116 236 5500

USA/ Mettler-Toledo, Process Analytical, Inc., 900 Middlesex Turnpike, Bld. 8, Billerica, MA 01821, USA Canada Phone +1 781 301 8800, Freephone +1 800 352 8763, Fax +1 781 271 0681

www.mt.com/pro

Subject to technical changes.05/2015. © Mettler-Toledo AG. Printed in Switzerland. 52 300 439

Mettler-Toledo AG, Process Analytics, Im Hackacker 15, CH-8902 UrdorfTel. +41 44 729 62 11, Fax. +41 44 729 66 36