Perodua Eco-Challenge 2013 Rules and Regulation 2013
-
Upload
mohamad-faiz -
Category
Documents
-
view
225 -
download
0
Transcript of Perodua Eco-Challenge 2013 Rules and Regulation 2013
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 1/24
Technical Regulations (v 1.1) Technical Regulations (v 1.1)
u es an egu a ons oPerodua Eco-Challenge 2013
Hasrol Hashim
Technical Director of PEC
Technical Regulations (v 1.0)
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 2/24
A. Vehicle Basic Configuration
• Minimum seated 4 people with luggage.
• .
(100% from body structure need to be covered with bodyshell).
• Steel ,Aluminum or f iber body skins.
-
• Powered by K3-VE with 4 speed transmission.
• Full equipped with A/C and stereo system
• Standard etrol tank.
22© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 3/24
A1 . Vehicle Modification Guide.
• Cut line must be at the A-A area
A-A
• No modification on the apron ,floor, cowl top , dash
,
minor cut.
• No modification on engine mounting, suspension
33© 2011 PERODUA
, ,
system.
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 4/24
B. Vehicle specifications
. ze
Overall Height
• No part for the car can be higher than 1350 mm from the ground.
Overall width
• Body shells maximum width must 1665 mm
• The overall width of the tire track shall not more than 1500 mm wheels
Wheelbase
• The car should have a minimum wheelbase of 2440mm. To changes are
allowed from the standard specs.
• The car should have minimum ground clearance of 100mm,(-0,+50 mm)
with driver onboard.
44© 2011 PERODUA
ar we g
• Free weight setting.
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 5/24
B. Vehicle specifications
B.2 Seats
• Driver must be provided with an appropriately constructed seat
cons s ng o a ase squa an ac res .
• Operating a vehicle in an extremely inclined position induces fatigue,
revents the driver from securin sufficient visibilit and ma interfere
with the effective functioning of the seatbelt in the event of collision.
• The lowest point of the driver’s seat must be no lower than the bottom.
55© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 6/24
B. Vehicle specifications
B.3 Safety Belts
• .
standard is that belts shall be a commercially manufactured lap andharness type (4-point) safety belt or the manufacturer standard 3 point
seat belts.
• Anchorages must be designed and installed in accordance with sound
engineering practice.
. a e y ruc ura o ar
• Vehicles must incorporate a structural roll bar in accordance with
.modified to incorporate this standard.
66© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 7/24
B. Vehicle specifications
. r ver ro ec on ee ppen x
• The vehicle shall be constructed or adapted to protect, as far as is
reasonably possible, the driver in the event of collision or vehicle roll-
.
• Steps should be taken to ensure that vehicle components, accessoriesor other components do not impinge on the driver space.
• The interior must be made b fire-resistant material.
B.6 Main Frame Body ( Roll cage) (See Appendix 1)
• The main frame must be of space frame tube construction.• The connection between steel tube to monocoque body must be done
by permanent welding or bolt on to the floor.
• For welding attachment it must be done carefully since the panel is very
.
• Main frame must consist of ferrous metal as the basic material.
• The use of aluminum extrusion beam are also allowed.
77© 2011 PERODUA
driver and passenger.
• The paint scheme is not restricted.
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 8/24
B. Vehicle specifications
B.7 Doors and Openings
•
vehicle without assistance. The doors must be able to be secured andreleased from both inside and outside the vehicle. Teams will be
required to demonstrate that the driver can enter and exit the vehicle
unass ste n no more t an secon s.
Hinges weld to roll
cage or body
side bar Original lock striker must
be use
88© 2011 PERODUA
• All team with new door design must include a reinforcement bar across
the door which connected from pillar to pillar of the roll cage.
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 9/24
B. Vehicle specifications
B.7 Doors and Openings
• The door hinge must be at the original position or on the roll cage.
• All original door lock must be use and link with side bar.
• All original door outer or inner handle must be used, however new links
is required for the new door.
• If emergency egress involves permanent damage to the vehicle then the
Team Manager will need to declare the method of extraction to the
satisfaction of the Chief Scrutineer at the time of scrutineering.
the vehicle.
• Securing of any egress canopy or hatch with adhesive tape is not
permitted.
99© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 10/24
B. Vehicle specifications
B.8 Brakes
• ,
system should fail, the vehicle can still be stopped.• The vehicle must demonstrate the ability to stop within 35 m from 50
km/hr to 0 km/hr.
• The ABS features should be kept in working order.
• The vehicle must be equipped with a parking brake capable of holding
the vehicle (including driver) on an incline of 18°.
B.9 Tyres
• Tires must be able to safely withstand the loads and forces imposed bythe vehicle mass, speed capability and braking.
• Tires must be suitably designed and rated and used in accordance with
t e manu acturer s recommen at ons.
1010© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 11/24
B. Vehicle specifications
B.10 Windows and windscreens
• All windows must be made of a material which is highly resistant to
rea ng or ma or amage. n ows w c are necessary to ensure t e
driver’s vision must be made of glass or similar transparent material thatdoes not distort vision.
•
the driver cannot be easily observed from outside the car.
B.11 Vision
• The driver must have vision in all directions to the satisfaction of the
Chief Scrutineer. Rear vision may be electronic and/or mirror. Electronic
rear vision systems must operate whenever the vehicle is in motion oridling.
1111© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 12/24
B. Vehicle specifications
. eer ng sys em
• The steering must use a mechanical linking system.
• e s eer ng sys em mus e con ro e y a s eer ng w ee any es gn
is ok).• The vehicle must be able to make a U-turn in either direction within a
.
• No removal of the power steering system.
.
• Rear brake lamps, front and rear turn indicators and front and rear
.
road users at a distance of 30 m.
• An audible warning device (horn, hooter, klaxon etc.) must be
permanently fitted to the vehicle and demonstrated to the satisfaction of
1212© 2011 PERODUA
the scrutineer.
• Driver must able to view speedometer while in the cockpit.
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 13/24
B. Vehicle specifications
. ec r ca
• All electrical equipment must comply with the relevant IEEE standards.
that it is impossible for the driver of the vehicle to touch live wires orterminals.
B.15 Driver safety
• All shar ed es chains and s rockets must be covered when in use
and internal components or cargo must be secured.
• Adequate ventilation must be provided to the driver.
B.16 Reversing mechanism
• The vehicles must be able to be driven backwards under their own
1313© 2011 PERODUA
power with the driver seated normally behind the steering wheel.
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 14/24
B. Vehicle specifications
. o y g y
• The vehicle’s body rigidity should be able to withstand both static
.
calculations / simulations / tests.
.
• The car must be equipped with a fully operational suspension system, .
• All suspension mounting points must be visible at Technical Inspection,
either by direct view or by removing any covers.
1414© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 15/24
C. Engine & Transmission Specif ications
C.1 Engine
•
must declare during presentation and scrutinizing session.
• Not allowed additional supplement for engine such as hydrogen, fuel
additive etc.
• Not allowed power enhancement such as electrical motor, fuel cell etc.
C.2 Transmission
• We allowed modification for transmission especially gear ratio or torque
converter locking mechanism.
1515© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 16/24
D. Driver Requirement
D.1 Driver Weight
• ,
not less than 60 kg, including driving shoes, suit, gloves and helmet.
• If the mass of the driver/passenger is less than 60 kg, ballast will be
added to make up the difference.
• No credit will be given if the driver/passenger weighs more than 60 kg.
• Correct ballast must be carried in the vehicle when driving.
• Ballast provided by the competitor will be subject to approval at
scrutineering.
• Additional ballast may be provided by the organizers.
1616© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 17/24
D. Driver Requirement
D.2 Drivers and Entrants Qualifications
• ,
vehicle driver's license recognized by Malaysian authorities.
• All drivers shall have a minimum experience of 12 hours driving the car
demonstrated by presentation of logbook.
• Only the nominated drivers may drive during race hours.
D.3 Driver’s Equipment
• The following equipment must be worn by the driver anytime he or she
is in the cockpit with the engine running.
• There must be no bare skin below the driver’s neck level when seated inthe vehicle.
1717© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 18/24
D. Driver Requirement
D.3.1 Helmet
• A well-fitting, closed face helmet.
D.3.2 Suit• A fire resistant suit that covers the body from the neck down to the
ankles and the wrists. The suit must be in ood condition, i.e. it must
have no tears or open seams, or oil stains that could compromise its fire
resistant capability.
D.3.3 Gloves
• Fire resistant gloves which are free of any holes.
D.3.4 Shoes• Shoes of durable fire resistant material and free from any holes.
1818© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 19/24
E. Precautions
A. When removing the roof.
As the roof is being cut away , the floor loses its rigidity and it will twists and
buckle therefore it is necessar to reinforce the bod usin tem orar
structure/braces until the actual roll cage are ready.
Fig 2
1919© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 20/24
F. Judgment
A. Time Attack
Slalom , parking , turning and others.Winner is base on
.
Conditions
Only one driver for loading
No modification from FC set up
.
Twin ECUs or by switching on engine control are allow.
Others conditions will be info later.
2020© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 21/24
F. Judgment
B. Fuel Consumption
The car to be subjected to simulated urban driving condition with these
condition :
Traffic light
Crossing
Highway
Hill climbing
Heavy traffic
Parking and others.
Conditions
The car will be subjected to maximum loading (60x5+15kg) , full air
conditioning setting and normal driving conditions.
MeasurementCase 1 : FC Base on the fuel weight .usage after 1 hour running.
Case 2 FC Base on 1 liter custom tank.
2121© 2011 PERODUAFinal conditions will be confirm later.
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 22/24
Appendix 1
• All vehicles must be equipped with the first and second roll bars (side
impact bar) to prevent direct damage to the driver and serious cockpit
deformation in the event of a collision or of a car turning over.
• The first and second roll bars form the basic element of the rollover
structure. These structures must be made of steel tubes or other
ma er a o su c en ens e s reng o pro ec e r ver rom a orce o
4w (w=weight of vehicle). The structure must be bolted, welded or
otherwise structurally incorporated to the vehicle according to sound
en ineerin ractice.
• For vehicles whose bodywork fulfills the function as the first and second
roll bars, the installation of additional roll bars is not necessary.
• (to show calculation or test for strength analysis will an advantage).
2222© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 23/24
Appendix 1
• Roll bars must be designed and constructed so that, when correctly
installed, they minimize the risk of injury to the driver.
• The responsibility to secure the necessary strength rests with
competitors.
• No part of roll bars must hamper the entry/exit of the driver or take upthe space designed for the driver.
• e ow are e examp e o s mp e ro cage es gn w c su ower
impact requirement which is suitable during the race. (not FIA standard
design) Fig 1
2323© 2011 PERODUA
8/13/2019 Perodua Eco-Challenge 2013 Rules and Regulation 2013
http://slidepdf.com/reader/full/perodua-eco-challenge-2013-rules-and-regulation-2013 24/24
Appendix 2
Side Impact Protection
normal driving position using a minimum of three (3) frame members asshown in a figure below.
Side impact bar
attached to 3 point
on the main Door original lock
Hip point
• Side impact bar - A frame member must connect the first roll bar and
second roll bar at a height same level as the driver hip point with driver
seated in the normal drivin osition.
2424© 2011 PERODUA