PERMITS AND PERMIT APPLICATIONS TO THE AIR DISTRICT …...Maximum hourly fuel usage 7.089 MMBtu/hr...

APPENDIX E PERMITS AND PERMIT APPLICATIONS TO THE AIR DISTRICT FOR

GENERATORS AND BOILERS

APPLICATION TO THE AIR DISTRICT FOR AN AUTHORITY TO

CONSTRUCT AND PERMIT TO OPERATE FOR BOILERS

r!/)l Golder Associates

September 29, 2015

Mr. Patrick Griffin County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097

RE: AUTHORITY TO CONSTRUCT/PERMIT TO OPERATE APPLICATION CRYSTAL GEYSER WATER COMPANY, MT. SHASTA, CA FACILITY

Dear Mr. Griffin:

Project No. 1405838

Golder Associates has been retained by Crystal Geyser Water Company (CGWC) to assist with the permitting of proposed emission sources at the Crystal Geyser bottling plant located near Mt. Shasta, California. This location was previously the Coca-Cola Dannon (CCDA Waters) bottling facility and will be re-equipped to become a beverage manufacturing facility again. This submittal is for an Authority to Construct and Permit to Operate to install four propane-fired boilers.

Background

In 201 3, CGWC purchased the former Coca-Cola Dannon (CCDA Waters) water bottling facility (Plant) located at 210 Ski Village Drive near Mt. Shasta, Siskiyou County, California. The Plant is adjacent to the northern portion of the city, on the southwestern flank of Mt. Shasta; it is bordered by Ski Village Drive to the north, Mount Shasta Boulevard to the west, McCloud Railroad to the south, and low-density residential development to the east. The facility is located outside the City of Mt. Shasta in Siskiyou County.

The existing infrastructure at the Plant was constructed between 2000 and 2002 by Dan non, prior to becoming CCDA Waters, and it consists of a 145,000 square foot building, a domestic well pump house, an approximately 228,000-gallon fire suppression tank, a deep groundwater production well (Dex-6), a leach field, and associated monitoring wells. CCDA Waters closed the Plant in 201 0, and it has remained closed until now. CGWC is currently remodeling the plant for their bottling lines. Equipment testing is expected in October through November 2015, with production to start sometime in 2016.

CGWC will be installing an aseptic bottling line for sparkling water, flavored water, tea, and juices. Aseptic filling produces a package that can be stored, shipped and sold at ambient temperatures. Sterility is achieved through a flash-heating process. CGWC proposes to install four 7.1 MMBtu/hr propane-fired boilers to provide steam for the manufacturing process. The boilers will be Miura Model LX(L)-200 SGI propane-fired boilers, with low NOx burners. A 30,000 gallon LPG horizontal pressurized vessel tank will be used to store the propane fuel.

CGWC initially proposes to bottle sparkling water. During this phase, only one boiler will be operated fulltime, and others will be operated on demand. The first boiler will provide base load for operating the sparkling water line and Clean-in-Place (CIP) system. In all, the sparkling line will likely require operating the first boiler at 100% capacity and a second boiler at 20% capacity.

Golder Assoc iates Inc. 9 Monroe Parkway, Suite 270

Lake Oswego, OR 97035 USA Tel: (503) 607-1820 Fax: (503) 607·1825 www.golder.com

Golder Associates: Operations in Africa, Asia, Australasia, Europe, North America and South America

Golder, Golder Associates and the GA globe design are trademarks of Golder Associates Corporation

Mr. Patrick Griffin County of Siskiyou, Air Pollution Control District 2

September 29, 2015 Project No.1405838

The boilers will eventually be used to bottle flavored water, tea and juices, in addition to sparkling water. Other than for testing purposes, full production may not occur until 2017. At full production, the CIP system may require the use of two boilers. During bottling and sterilization of aseptic products, two boilers will likely run at 100% capacity, with a third boiler to be operated on demand. The fourth boiler is a backup and is also reserved for future capacity. CGWC will use a boiler control system to alternate the boilers and spread the running hours somewhat evenly over the boilers.

Emissions

Golder obtained criteria pollutant emissions data from the boiler manufacturer, Miura. Hazardous air pollutant (HAP) and toxic air contaminant (TAC) emissions have been estimated using Mojave Desert Air Quality Management District (MDAQMD) default emission factors for commercial propane boilers. MDAQMD emission factors are more comprehensive than those emission factors found in AP-42. Emissions were estimated using the manufacturer's emission factors and assuming all four boilers will be operated for 8,760 hours of operation, as shown in Attachment 1, Table 1. Criteria pollutant and HAP/TAC emissions for a single boiler are shown on Attachment 1, Tables 2 and 3. Emissions for all four boilers are provided in Attachment 1, Tables 4 and 5.

Pressurized propane tanks will not have emissions except for emergency situations when a pressure relief valve is triggered. Emissions have not been estimated for this piece of equipment.

Regulatory Analysis

Siskiyou County Requirements

The following Siskiyou County Air Pollution Control District (SCAPCD) rules were evaluated for applicability:

Rule 4.4(B)

The particulate matter regulations of Rule 4.4(B) would apply to combustion pollutants from the boilers"No person shall discharge from any single source whatsoever any one or more of the following contaminants in any state or combination thereof, exceeding in concentration at the point of discharge -combustion contaminants - any source with an approved authority to construct after July 1, 1987: 0.20 grains per cubic foot of exhaust gas calculated to 12 percent carbon dioxide [C0 2] , at standard conditions."

Rule 4.4(0)

The oxides of nitrogen regulations of Rule 4.4(D) would apply to combustion pollutants from the boilers"No person shall discharge from any single source whatsoever any one or more of the following contaminants in any state or combination thereof, exceeding in concentration at the point of discharge -oxides of nitrogen - no person shall discharge oxides of nitrogen in excess of 140 pounds per hour for new or expanded installations, calculated as nitrogen dioxide (N02) ."

Regulation VI

Emissions are below the New Source Siting threshold of 250 pounds/day of any pollutant with a National Ambient Air Quality Standard and 2,500 pounds/day of carbon monoxide; therefore, SCAPCD Regulation VI does not apply.

final cgwc boiler application.docx

(!J!Golder Associates

Mr. Patrick Griffin County of Siskiyou, Air Pollution Control District

New Source Performance Standards

3 September 29, 2015 Project No.1405838

The New Source Performance Standard (NSPS}, 40 CFR Part 60, Subpart De - Standards of Performance for Small Industrial-Commercial-Institutional Steam Generating Units was evaluated to determine if applicable. The NSPS applies to boilers with a maximum design heat input capacity greater than 10 MMBtu/hr, but less than 100 MMBtu/hr. Since the each of the boilers Crystal Geyser is proposing to install are 7.1 MMBtu/hr, the NSPS does not apply.

National Emissions Standards for Hazardous Air Pollutants

The National Emission Standards for Hazardous Air Pollutants (NESHAP) for Source Categories, 40 CFR Part 63, Subpart JJJJJJ - National Emission Standards for Hazardous Air Pollutants for Industrial, Commercial, and Institutional Boilers in Area Sources was evaluated to determine if applicable to the project. The CGWC facility is a HAP minor source and is considered an area source under these regulations. This subpart contains exceptions to the rule in §63.11195 that includes "A gas-fired boiler as defined in this subpart". Section §63.11237 provides the definitions of "gas-fired boiler" which includes any boiler that burns gaseous fuels, "gaseous fuels" which includes natural gas, and "natural gas" which includes propane fuel as part of that definition. Since the Crystal Geyser boilers will only be fueled by propane, the boilers are exempt from this regulation.

Permit Application

For this submittal, the following additional information is being submitted with the Authority to Construct and Permit to Operate application:

• Attachment 1 -Emissions Inventory

• Attachment 2 -Authority to Construct Application Forms

• Attachment 3- Boiler Manufacturer Information

An Authority to Construct Permit/Permit to Operate Application form for each boiler is included in Attachment 2. The $50 filing fee under SCAPCD Rule 3.1 has been included for each of the boilers for a total of $200 submitted for this application.

The Rule 2.4 Completeness Criteria in Appendix A was reviewed to determine additional information that should be included in the application. The following information is provided to meet these requirements:

• Boiler manufacturer information is provided in Attachment 3. The Miura LX series on-demand steam boiler brochure is included which provides general and specific information on the boiler. Additionally, manufacturer's emissions data used in the emissions inventory (Attachment 1) are included. A building drawing with the location of the boilers is also provided.

• Boiler Manufacturer Serial Numbers:

Boiler 1: 47S414053U

Boiler 2: US01030002

Boiler 3: US01 030009

Boiler 3: US01 030013

• Boiler Exhaust Stack Parameter Information (each stack) :

Exhaust stack height above ground level: 36 feet

final cgwc boiler appllcation.docx

~

l'iJ:i' Golder \Z7 Asso,iates

Mr. Patrick Griffin County of Siskiyou, Air Pollution Control District 4

Exhaust stack diameter and shape: 20 inches, round

Exhaust flow rate: 107,690 seth wet, 93,860 seth dry

Exhaust outlet temperature: 270°F

September 29, 2015 Project No.1405838

Please review the contents of this Authority to Construct and Permit to Operate request application. If you have any questions or comments, please contact us at 503-607-1820 or by email at [email protected] or [email protected]. If this application appears complete after your review, we respectfully request your notification in writing that we may proceed with construction.

Sincerely,

GOLDER ASSOCIATES INC.

-·~~ Danielle M. Lenzini Senior Project Specialist

Chad Darby Associate

cc: Richard Weklych, Crystal Geyser Water Company

Barbara Brenner, Churchwell White LLP

Attachments

DML

final cgwc boiler application.docx (!/J' Golder

Associates

Attachment 1 Emissions Inventory

September 2015 140-5636

Table 1 Input Assumptions Crystal Geyser Water Company, Mt Shasta, CA

Parameter I Value I Comment

Crystal Geyser Facility Annual hours of operation I 8,760 hrs/yr Conservative assumption

Daily hours of operation I 24 hrs/dav Conservative assumption

Boiler Data Maximum hourly fuel usage 7.089 MMBtu/hr Combustion lest data sheet (lX(L}-200 SGI) dated June 25, 2014

Number of boilers 4 boilers

NDx emission factor 0 .0146 lbs/MMBtu Combustion test data sh~t (LX(L}-200 SGI) dated June 25, 2014, ba.ed on 12 ppm for low NOx burner

CO emission factor 0 .0369 lbs/MMBtu Combustion test data sheet (LX(L}-200 SGI) dated June 25, 2014, based on 50 ppm

C02 emission factor 137 lbs/MMBtu Combustion test data sheet (LX(l}-200 SGI) dated June 25. 2014

S02 emission factor 0 .001 1 lbs/MMBtu Combustion test date sheet (LX(L)-200 SGI) dated June 25, 2014

PM emission factor 0 .0077 lbs/MMBtu Combustion test data sheet (l..X(l)-200 SGI) dated June 25,2014

Golder Associates

September 2015

Table 2 Propane Boiler Criteria Emission Estimates (Each Boiler) Crystal Geyser Water Company, Mt. Shasta, CA

Source Daily hours of operation (hrs/day) Annual hours of operation (hrs/yr)

Maximum hourly fuel usage (MMBtu/hr)

LX-200 SGI (1) 24 (1) 8,760 (1) 7.089

Emission Estimates Pollutant Emission Factor Maximum Daily

(lbs/day) PM 0.0077 lbs/MMBtu (1) 1.31 (a)

PM1o 0.0077 lbs/MMBtu (3) 1.31 (a)

PM2.s 0.0077 lbs/MMBtu (3) 1.31 (a)

NOx 1.5E-02 lbs/MMBtu (1) 2.48 (a)

co 3.7E-02 lbs/MMBtu (1) 6.28 (a)

so2 1.1 E-03 lbs/MMBtu (1) 0.19 (a)

voc 1.00 lbs/Mgal (4) 1.87 (C)

C02 137.0 lbs/MMBtu (1) 23,309 (a)

CH4 6.6E-03 lbs/MMBtu (e) 1.13 (a)

N20 1.3E-03 lbs!MMBtu (e) 0.23 (a)

C02e 137.6 lbs/MMBtu (I) 23,404 (a)

Notes:

(a) Maximum daily emissions estimate (lbslday) = (emission factor [lbsiMMBtu]) x (maximum hourly fuel usage [MMBtulhrij)

x (daily hours of operation [hrslday])

(b) Annual emissions estimate (tonslyr) = (emission factor [lbs/MMBtu]) x (maximum hourly fuel usage [MMBtu/hr])

x (annual hours of operation [hrslyr]) x (ton/2,000 lbs)

Annual (tons/vr) 0.24

0.24

0.24

0.45

1.15 0.03 0.34

4,254

0.21

4.1E-02 4 ,271

(c) Maximum daily emissions estimate (lbslday) = (emission factor (lbs/Mgal]) x (Mgat/1 ,000 gal) x (maximum hourly fuel usage [MMBtu/hr))

x (daily hours of operation [hrslday])/ (propane high heat value [MMBtu/gaij) Propane high heat value (MMBtu/gal) = 0.091 (2)

(d) Annual emissions estimate (tonslyr) = (emission factor [lbsiMgaij) x (Mgal/1,000 gal) x (maximum hourly fuel usage (MMBtu/hr))

x (annual hours of operation [hrslyr]) / (propane high heat value [MMBtu/gal]) x (ton/2,000 lbs)

Propane high heat value (MMBtu/gal) = 0.091 (2)

(e) CH4 or N20 emission factor (lbs/MMBtu) = (CH4 or N20 emission factor [kg/MMBtu]) x (2.205 lbslkg)

CH4 emission factor (kg/MMBtu) = 3.0E-03 (6)

N20 emission factor (kg/MMBtu) = 6.0E-04 (6)

(f) CO,e emission factor (lbs/MMscf) = (CO, emission factor (lbsiMMBtu]) + (CH4 emission factor [lbs/MMBtu]

x CH. global warming potential) + (N 20 emission factor [lbs/MMBtu) x N 20 global warming potential)

Global warming potential of CH4 = 25 (7)

Global warming potential of N20 = 298 (7)

References:

(1) See Table 1,1nputAssumptions.

{2) 40 CFR Part 98 Subpart C, Table C-1. "Default C02 Emission Factors and High Heat Values for Various Types of Fuel".

(3) Assumes that 100% of PM is PM2.5. Therefore, 100% of PM10 is PM2.5 .

(4) AP-42 Chapter 1.5 (July 2008) Table 1.5-1 , "Emission Factors for LPG Combustion". Assumes VOC is equivalent to TOG.

(5) 40 CFR Part 98 Subpart c , Table c-1, Default C02 Emission Factors and High Heat Values for Various Types of Fuel.

(6) 40 CFR Part 98 Subpart C, Table C-2, Default CH4 and N20 Emission Factors for Various Types of Fuel.

(7) 40 CFR Part 98 Subpart A, Table A-1 . Global Warming Potentials.

Chur<:hwell Whfte Bottling Plan I El - VO 2.xlsx Golder Associates

140-5838

(b)

(b)

(b)

(b)

(b)

(b)

(d)

(b)

(b)

(b)

(b)

September 2015

Table 3

Propane Boiler HAPfTAC Emission Estimates (Each Boiler)

Crystal Geyser Water Company, Ml Shasta, CA

Source Daily hours of operation (hrs/day)

Annual hours of operation (hrslyr)

Maximum hourly fuel usage (MMBtu/hr)

LX-200 SGI (1) 24 (1) 8,760 (1) 7.09

Emission Estimates

TAC CAS Emission Factor

Maximum Daily <•l (lbs/Mgal) (lbs/day)

7, 12-Dimethylbenz(a)anthracene 57-97-6 1.5E-06 (2) 2.7E-06

Acetaldehyde 75-07-0 2.8E-04 (2) 5.30E-04

Benzene 71-43-2 5.3E-04 (2) 9.92E-04

Dichlorobenzene 25321-22-6 1.1E-04 (2) 2.05E-04

Ethylbenzene 100-41-4 6.3E-04 (2) 1.18E-03

Fluoranthene 206-44-0 2.7E-07 (2) 5.13E-07

Formaldehyde 50-00-0 6.9E-03 (2) 1.28E-02

n-Hexane 110-54-3 4.2E-04 (2) 7.87E-04

Naphthalene 91-20-3 2.7E-05 (2) 5.13E-05

Propylene 115-07-1 4.8E-02 (2) 9.07E-02

Toluene 108-88-3 2.4E-03 (2) 4.53E-03

Xylenes 1330-20-7 1.8E-03 (2) 3.37E-03

Arsenic 7440-38-2 1.8E-05 (2) 3.42E-05 Beryllium 7440-41 -7 1.1 E-06 (2) 2.05E-06

Cadmium 7440-43-9 1.0E-04 (2) 1.88E-04

Chromium VI 18540-29-9 1.3E-04 (3) 2.39E-04 Cobalt 7440-48-4 7.7E-06 (2) 1.44E-05 Copper 7440-50-8 7.8E-05 (2) 1.45E-04

Lead 7439-92-1 4.6E-05 (2) 8.55E-05

Manganese 7439-96-5 3.5E-05 (2) 6.50E-05

Mercury 7439-97-6 2.4E-05 (2) 4.45E-05

Nickel 7440-02-0 1.9E-04 (2) 3.59E-04

Selenium 7782-49-2 2.2E-06 (2) 4.11E-06

Notes:

(a) Maximum daily emissions estimate (lbs/day) = (emission factor [lbs/Mgal]) x (maximum hourly heat input [MMBtulhr))

x (daily hours of operation [hrs/day]) I (propane high heat value [MMBtulgal] x (Mgal/1 .000 gal))

Propane high heat value (MMBtulgal) = 0.091 (2)

(b) Annual average emissions estimate (tons/yr) = (emission factor Vbs/Mgal)) x (maximum hour1y heat usage [MMBtulhr])

x (annual hours of operation [hrslyr]) I (propane high heat value [MMBtu/gal]) x (Mgal/1 ,000 gal) x (tons/2,000 lbs)

Propane high heat value (MMBtu/gal) = 0.091 (2)

References:

(1) See Table 1, Input Assumptions.

(2) Mojave Desert Air Quality Management District default emission factors for commercial propane boilers (2013).

Annual (bJ

(tons/yr)

S.OOE-07 9.68E-05 1.81 E-04

3.75E-05 2.15E-04

9.37E-08

2.34E-03

1.44E-04

9.37E-06

1.65E-02

8.27E-04

6.15E-04 6.24E-06 3.75E-07

3.43E-05

4.37E-05 2.62E-06 2.65E-05

1.56E-05

1.19E-05

8.12E-06

6.56E-05

7.49E-07

(3) Mojave Desert Air Quality Management District default emission factors for commercial propane boilers (2013). Chromium VI is

assumed to be equivalent to the Total Chromium emission factor.

Churchwell White Bottling Plant El - VO 2.xlsx Golder Associates

140-5838

September 2015

Table 4

Emissions Summary - Criteria Emission Estimates (All Boilers)

Crystal Geyser Water Company, Mt. Shasta, CA

Total Emission Estimates Summary Pollutant Maximum Daily (a) Annual (b)

(lbslday) (tonslyr) PM 5.24 0.96

PM10 5.24 0.96

PM2.s 5.24 0.96

NOx 9.94 1.81

co 25.11 4.58 802 0.75 0.14

voc 7.48 1.36 C02 93,235 17,015

CH4 4.50 0.82

N20 0.90 1.6E-01 C02e 93,615 17,085

Notes:

(a) Total maximum daily emission estimates= (Maximum daily emission estimates per boiler (lbs/day]) x (Number of boilers)

Number of boilers = 4 (1)

(b) Total annual emission estimates= (Annual emission estimates per boiler [tonlyr]) x (Number of boilers)


References:

(1) See Table 1, Input Assumptions. Maximum daily and annual average emission estimates are from Table 2.

Churchwell White Bottling Plant El- VO 2.xlsx Golder Associates

140-5838

September 2015

Table 5

Emissions Summary- HAP/TAC Emission Estimates (All Boilers)

Crystal Geyser Water Company, Mt. Shasta, CA

Total Emission Estimates Summary Pollutant Maximum Daily (a) Annual (bl

tlbs/davl (tons/vr) 7, 12-Dimethylbenz(a)anthracene 1.09E-05 2.00E-06

Acetaldehyde 2.12E-03 3.87E-04

Benzene 3.97E-03 7.24E-04

Dichlorobenzene 8.21 E-04 1.50E-04

Ethyl benzene 4.72E-03 8.62E-04

Fluoranthene 2.05E-06 3.75E-07

Formaldehyde 5.13E-02 9.37E-03

n-Hexane 3.15E-03 5.74E-04

Naphthalene 2.05E-04 3.75E-05

Propylene 3.63E-01 6.62E-02

Toluene 1.81 E-02 3.31E-03

Xylenes 1.35E-02 2.46E-03

Arsenic 1.37E-04 2.50E-05

Beryllium 8.21E-06 1.50E-06 Cadmium 7.53E-04 1.37E-04

Chromium VI 9.58E-04 1.75E-04

Cobalt 5.75E-05 1.05E-05 --

Copper 5.82E-04 1.06E-04

Lead 3.42E-04 6.24E-05

Manganese 2.60E-04 4.75E-05

Mercury 1.78E-04 3.25E-05

Nickel 1.44E-03 2.62E-04 Selenium 1.64E-05 3.00E-06

Notes:

140-5838

(a) Total maximum daily emission estimates= (Maximum daily emission estimates per boiler (lbs/day]) x (Number of boilers)


(b) Total annual emission estimates= (Annual emission estimates per boiler [ton/yr]) x (Number of boilers)


References:

(1) See Table 1, Input Assumptions. Maximum daily and annual average emission estimates are from Table 3.

Churchwell White Bottling Plant El - VO 2.xlsx Golder Associates

Attachment 2 Authority to Construct Application/Permit to Operate

Forms

Siskiyou County APCD ATC I PTO Application

County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097 Phone #: (530) 841-4029; 841-4031 Fax#:(530)842~90

Permit Application For: -New Construction IZl

D D 0

Authority To Construct (ATC) Authority To Constmct (A TC) Authority To Construct (ATC) Permit to Operate (PTO)

-Modification ofE:nllssion Unit to a Valid P'l'O/ATC

-Change of Location

-ownership change

L PERMlT TO BE ISSUED To: Crystal Geyser Water Company

2. MAILING ADDREss:

STREE'l' I P.O Box: 501 Washington Street

Cl'lY Calistoga STATE= California

3. LoCATION WHERE THE EQUIPMENT WILL BE OPERATED: STREET21 0 Ski Village Drive CrrY: Mt Shasta

TOWNSHIP:40N RANcE:04W

4. GENERAL NATURE OF BUSINEss: Beverage Manufacturer

ZIP CODE: 94515

Within 1,000 ft of a school? 0 Yes 0 No

S.LC. Code of Facility: 2086

Proposed install date: Oct 2015 Proposed Completion date: Nov 2015

5. DESCRIPTION OF EQUIPMENT OR MODIFICATION FOR WHICH APPLICATION IS MADE: (INCLUDE ADDITIONAL

SHEETSASNESSECCARY) Miura Model LX(L)-200 SGI Propane 7.1 MMBtu/hr Boiler (Boiler 1)

6. HAVE YOU EVER APPLIED FOR AN ATC OR PTO IN SISKIYOU COUNTY?0 NdZJ YES, IF YES, PERMIT#:

7. Is THIS PROPERTY ZONED PROPERLY FORTHlS PERMiT? 0 NO [Z]YES, IF YES, ZONE CODE#:

8. IS THE EQUIPMENT REGISTREDWITH CARB.? lZJ No 0YES, IF YES, REG.#:

9. TYPE oF ORGANIZATioN: CoRPORATION,~ PARTNERSHIP, OINDrvmuAL, OGoVERNMENT AGENCY, D 10. TYPE OR PRINT NAME OF APPLICANT: Richard Weklych

/;;NATUR:=~~DATE iu/J' TITLE OF APPLlCAN'r: EVP Manufacturing

PHONE#: (707) 972-0500 FAX#:

E -MAIL: [email protected]

A $50.00 filing fee must accompany each applicationls (District rule 3.1 Perm it Fees) Date paid:

For transfer of ownership or location a $20.00 transfer fee must accompany application (District rule 3.1 Permit Fees) Date:

Make check payable to: Siskiyou County Air Pollution Control District.

1 of 1 G:\DATA\Air Pollution\Forms and Templates


County of Siskiyou

Air Pollution Control District 525 South Foothill Drive Yreka, California 96097 Phone #: ( 530) 841-4029; 841-4031 Fax#: (530) 842-6690

Permit Application For: -New Construction 0

D D 0

Authority To Construct (ATC) Authority To Construct (ATC) Authority To Construct (ATC) Permit to Operate (PTO)

·Modification of Emission Unit to a Valid PTOIATC

-Change of Location

·ownership change

1. PERl.VllT TO BE ISSUED TO: Crystal Geyser Water Company

2. MAn1NG ADDREss:

STREET I P.O Box: 501 Washington Street

CITY: Calistoga STATE= California

3. LoCATION WHERE THE EQUIPMENT WILL BE OPERATED:

STREET21 0 Ski Village Drive CI1Y Mt. Shasta

SECTION: 9 TOWNsHIP:4QN RANGE:04W

4. GENERAL NATURE OF BUSit\lESS: Beverage Manufacturer

ZIP CODE: 94515

Within 1,000 ft of a school? 0Yes 0No

S.I.C. Code of Facility: 2086

Proposed install date: Oct 2015 Proposed Completion date: Nov 2015

5. DESCRIPTION OF EQUIPMENT OR MODIFICAT!ON FOR WHICH APPUCATlON JS MADE: (INCLUDE ADDITIONAL

SHEETSASNESSECCARY) Miura Model LX(L)-200 SGI Propane 7.1 MMBtu/hr Boiler (Boiler 2)

6. HAVE YOU EVER APPLIED FOR AN ATC OR PTO IN SISKIYOU COUNTY?0 Nd{] YES, IF YES, PERMIT#:

7. Is THis PROPERTY zoNED PROPERLY FOR THis PERMIT? D No [Z]YEs, IF YEs, ZoNE coDE#=

8. Is THE EQUIPMENT REGISTRED WITH CARE.? 0 No DYEs , IF YEs, REa.#:

9. TYPE oF ORGANIZATION: CoRPORATION, ba PARTNERSHIP, OINDIVIDUAL, OGoVERNMENT AGENCY, D 10. TYPE OR PRlNT NM1E OF APPLICANT: Richard Weklych TITLE OF APPLICANT: EVP Manufacturing

11. SIGNATURE OF APPLICANT: DATE: PHONE#: (707) 972-0500

/~ J ts:2-_, ~)S ~"!;L• R;[email protected]

A $50.00 filing fee must a~company each applicatwnls (District rule 3.1 Permit Fees) Date paid=



1 of 1 G:\DATA\Air Pollution\Fonns and Templates

Siskiyou County APCD A TC I PTO Application

~

[Z] D D 0

County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097 Phone#: (530) 841-4029; 841-4031 Fax#:. (530) 842-6690

Permit Application For: Authority To Construct CATC) Authority To Construct (ATC) Authority To Construct CATC) Permit to Operate (FTO)

·New Construction

·Modification of Emission Unit to a Valid ?rOtATe

·Change of Location

·ownership change

1. PERMIT TO BE ISSUED ro: Crystal Geyser Water Company

2. MAILING ADDREss:

STREET/P.OBox: 501 Washington Street

CrTY: Calistoga STA'l'E: California ZIP ConE: 94515

3. LoCATION WHERE THE EQUIP~lENT Wl LL BE OPERATED: Within 1,000 ft of a school? STREET21 0 Ski Village Drive Cl'rv: Mt. Shasta 0 Yes 0 No

S.LC. Code of Facility: 2086 SECTION: 9 TOWNSHJP: 40N RANGE: 04W

Proposed install date: Oct 2015 PnJposed

4. GENERAL NATURE OF BUSINESS: Beverage Manufacturer Completion date: Nov 2015

5. DESCRIPTION OF EQUIPMENT OR MODIFICATION FOR WHICH APPLICATION IS MADE: (iNCLUDE ADDITIONAL

SI!EE,"''SASNESSECCARY) Miura Model LX(L)-200 SGI Propane 7 .1 MMBtu/hr Boiler (Boiler 3)

6. HAVE YOU EVER APPLIED FOR AN ATC OR PTO IN SISKIYOU COUI\l'fY?0 NdZJ YES, IF YES, PERMIT#:

7. Is TffiS PROPERTY ZONED PROPERLY FOR THIS PERMIT ? 0 NO 12JYES, I F YES, ZONE conE#:

8. Is THE EQUIPMENT REGTSTRED WJTH CARB.? 121 No D YEs, IF YEs, REa.#:

9. TYPE OF ORGANIZATION: CO}{PORATION, 0 PARTNgRSHIP, D INDIVIDUAL, D GovEHNMENT A GENCY, 0 10. TYPE OR PRINT NAME OF APPLTCAN'l': Richard Weklych TITLE OF APPLICANT: EVP Manufacturing

11. SIGNATURE OF APPLICANT D ATE: PHONE#: (707) 972-0500 // 0 FA~: ~ ~ o/, 24j/r E-MAll-' R;cha,dW@c'Ystalgeyse,.com ~ -..... }

A $50.00 filing fee must acco~pany each application/s (Dist,;ct ntle 3.1 Permit Fees) Date paid:

For transfer of ownership or location a $20.00 transfer fee must accompany application (District rule 3.1 Permit Pees) Date:

Make ch eck payable to: Siskiyou County Air Pollution Control District.



/

IZI D D IZI

County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097 Phone#: (530) 841-4029; 841-4031 Fax#: (530) 842-6690

Permit Application For: Authority To Construct (ATC) Authority To Constl'Uct (A TC) Authority To Construct (ATC) Permit to Operate <PTO)

·New Construction

·Modification ofEmission Unit to a Valid PTO/ATC

·Change of Location

-ownership change

1. PERl\!IlT TO BE ISSUED To: Crystal Geyser Water Company

2. MAiLING ADDREss:

STREET /P.O Box: 501 Washington Street

CrTY: Calistoga STATE= California ZIP ConE: 94515

3. LoCATION WHERE THE EQUIPMENT WILL BE OPERATED: Within 1,000 ft of a school? STREE'r21 0 Ski Village Drive ClTY: Mt. Shasta 0 Yes0No

SEC'rioN: 9 T OWNSHW: 40N S.I.C. Code of Facility: 2086

RANGE: 04W Proposed il1stall date: Oct 2015 Proposed

4. GENERAL NATURE OF BUSINEss: Beverage Manufacturer Completion date: Nov 2015

5. DESCRIPTION OF EQUIPMENT OR MODIFICATION FOR WHICH APPLICATION IS MADE: (IKCWDE ADDITIONAL

SHEETSASNESS~CCARY) Miura Model LX(L)-200 SGI Propane 7.1 MMBtu/hr Boiler (Boiler 4)

6. HAVE YOU EVE H. APPLIED FOR AN ATC OR PTO IN SISKIYOU COUN1'Y?0 Nd{] YES, IF YES, PERMrT#:

7. Is THIS PROPERTY zoNED PROPl'~l:tLY FOR THIS PERMIT'! 0 No [ZJYES, IF YES, ZONE conE#:

8. Is TI-lli EQUIPMENT REGISTRED WITH CARB.? 0 No DYES, IF YES, REG.#:

9. TYPE OF ORGANIZATioN: CoRPORATION, 0 PARTNERSHJP, O INmvruuAL, D GovERNMENT AGENCY, D 10. TYPE OR PRINT NAME OF APPLICANT: Richard Weklych TITLE OF APPLICANT: EVP Manufacturing

11. SIGNATURE OF APPLICANT:

DA~~J/ PHONE#: (707) 972-0500

~0~ FAX#:

/(< E -MJ\TL: [email protected]

A $50.00 filing fee must accompany each applicationls (District rule 3.1 Permit Fees) Date paid:




Attachment 3 Boiler Manufacturer Information

•

The, BL Micro Controller Boiler Control System

Miura Gas-Fired/ Low NOx LX Series High Pressure Steam Boiler

l

On-Demand Steam Solutions

• lVI lURA.

•

MIURA'S LOW NOx SERIES ON-DEMAND STEAM BOILERS SAVE20%on ENERGY COSTS and RmUCE HARMFUL EMISSIONS

Water to Steam in 5 minutes

Miura Boilers produce steam in 5 minutes using floating header that results in our customers using substantially less gas and oil. On average our customers save 20% on fuel costs and equivalent C0

2 reductions. Given

ever-increasing concern with energy costs & C02 emissions, forwardthinking organizations recognize the

Miura is known world-wide for our commitment to protecting the environment and our innovative and efficient boiler designs. Our low NOx steam and hot water boilers meet and exceed current and proposed regulations for nitrous oxide emissions levels, as low as 9ppm NOx at 3%, corrected 02.

• Gas {Ired: Natural Gas or Propane

• High and low pressure steam options available (300 MAWP, 250 MAWP, I 70 MAWP or 15 MAWP)

• Hot water boilers ore available depending on models (refer to a Miura hot water boiler catalog for details)

• Compact, an LX 200 Boiler can fit through a standard doorway

• Naturally low NOx (nitrogen oxides) Rating as low

as 9ppm depending on model

PROFITS

Modular "MI System" offers enhanced design flexibility & energy management ~::----.......... ~=-=-~

to build an On-Demand steam plant customized to meet site-specific demand requirements.The Ml System provides both the flexibility to build-to-suit current steam loads within very tight tolerances while allowing ease of future expansion of system

energy management capability by providing higher efficiency during

stage multiple units on/off in response to demand

fluctuations.

• Greater control over steam pressure settings for steadier steam pressure.

• Allows for compensated adjustment of high and low fire scale thermocouple settings.

• Allows for compensated adjustment of automatic blowdown based upon Total Dissolved Solids (TDS) and/or blowdown rates.

• Easily interfaces with the Miura "Colorrnetry" unit to minimize scale formation due to water softener failure.

behind Miura's enhanced energy management system, offers significant

of over 60% compared to our popular Xj I Controller.

The BL Controller provides robust 24/7 boiler Monitoring, Measuring & Verification (MM&V) capabilities and enhances troubleshooting by identifying problems and suggesting solutions via an easy-to-read display that interfaces with Miura Online Maintenance® software. Information is accessible both on site and on-line .The BL Controller features simple, intuitive programming that is easy to set up, program and operate. When combined with our O&M training program, the easy-to-use interface provides your facility with an intelligent boiler system to optimize energy and personnel management for increased productivity, efficiency and a reduced environmental impact.

High Performance via Enhanced Control Capability The BL Micro Controller Boiler Control System measures the performance of your boiler in an easy-to-read, user-friendly format:

• Stearn Pressure • Flue Gas Temperature • Feed Water Temperature • Scale Monitor Temperature • Overheat Monitor Temperature • Flame Current • Remaining Time to Blowdown • Automatic Surface Blowdown Valve (On/Off) • Water Conductivity • 11-Point Boiler Management Data ... Plus many more

Top view of Flame Pattern Low NOx output (aslowas9ppm)

reduces harmful emissions Built-in Online Monitoring

Fuel savings and reduced emissions go hand-in-hand. Miura's "green" technology maximizes energy efficiency to reduce the level of harmful emissions created from every pound of useful steam generated. How does it work/ Our unique burner design produces a lower temperature flame and spreads it over a large

••!M!!!!!!!J•IJ surface area to enhance heat transfer. This naturally Burner Head reduces the formation of NOx during combustion.

Reduced Boiler Footprint design utilizes a low volume pressure vessel offering output capacities comparable to much larger conventional boilers. The resulting reduced boiler footprint provides design flexibility, reduced

construction costs and enhanced Miura offers the most BHP utilization of existing space. capacity I sq. ft. of boiler footprint

Efficiency is also measured in consistent, reliable performance and Miura offers a robust suite

monitoring systems integrated with its BL boiler controller to provide

Maintenance®

in real time + 4 seconds preceding them to provide

is standard with every unit and Miura offers monitoring to subscribing customers with a free 12-month trial of

the service.

A Standard of Performance that sets Miura apart from other Steam Boiler manufacturers In-Service Efficiency is a measure of overall boiler system performance, no matter your load profile. High In-Service Efficiency is the level of performance every Miura customer can expect.This standard of excellence has been established based on taking all factors of the boilers operation into account (see chart).

For a further explanation,

Definitions of Efficiency as related to the Boiler:

Miura has developed the term "In-Service Efficiency" to include Combustion Efficiency, Thermal Efficiency and all of the other energy

Fuel In

Radiation Loss

Exhaust Loss

Fuel-to-Steam Efficiency

Start-Up Losses

Pre- & Post-Purge Losses

Blow-Down Losses

Loss at High Turndown

In-Service Efficiency

Changing Loads

Radiation Loss at Idle I Stand-by

operational cycle that contribute to operating efficiency including: radiation losses, blow-down losses, pre- and post-purge losses, and other losses that occur during changing loads, high turn-down, part-load and stand-by operation.

In-Service Efficiency is a more comprehensive measure of boiler efficiency. It better reflects a boiler's contribution to

performance indicator, In-Service Efficiency is the best measure of the true cost of steam.

Highest In-Service Efficiencies in the commercial I industrial boiler industry

100

80

60

40

20

In-Service Efficiencies

.. • .. l • .. .. .. • -~.r~~~~·~: .... . "

' • ... . .

• Miura Boiler • Watertube Boiler

Firetube Boiler Each dot represents one boiler tested.

o ...._ __ r--~-1"---r---....---20 40 60 80 100

Load(%)

century, providing energy savings averaging 20% over other boiler designs. At I 0% to 40% fuel savings, Miura can save about $200,000 per year in fuel for a typical I 5,000 lbs/hr steam load under 24/7 operation (assuming $0.50 I therm) with reduced C02 emissions of over I, I 00 metric tons per year .

The chart (left) compares in-service efficiencies of Miura boilers with both conventional firetube and watertube boilers. Miura's low volume design results in optimal heat transfer with fuel-to-steam efficiencies of 85% at all load conditions. Although typical firetube designs can deliver up to 83% fuelto-steam, studies comparing actual operating In-Service Efficiencies have shown Miura averages I 0% to 40% in fuel savings over standard firetube designs.

Whereas conventional boiler efficiency is significantly reduced during partload conditions, Miura offers consistently high operating efficiency at all load conditions.

(Inches)

FRONT VIEW LX-50 SG(I) 79

LX-100 SG(f) 38 124 142 111 79

LX-150 SG(f) 40 139 157 126 85

LX-200 SG (I) 40 139 157 126 85

(: "\LX-300 SG(I)••• 63 155 155 127 108

* Minimum height for Boiler Knock Down ** '82' Dimension is for SGI models with Inverter Box *** Drawing not applicable for LX-300SG (see LX-300 insert)

TOP VIEW

' '

-Al

SIDE VIEW

... 1 BOILER VESSEL

2 STEAM SEPARATOR

3 UQUID VOLUME CONTROLLER

4 WIND BOX

5 FAN (AIR INLET)

6 ELEGRICAL CABINET

7 BL CONTROLLER

:r: 8 MANUAL BLOW DOWN

9 STEAM OUTLET 10 MAIN SAFETY VALVE

* 11 STEAM PRESSURE GAUGE .£ 12 MAIN GAS INLET

13 FEED WATER INLET 14 ECONOMIZER

15 INVERTER BOX (OPTION)

16 LIFTING LUGS

1-----------B2liEliE---------- I

Maximum Pressure

[ --Eq-u-iv-a-lent Output (*2)

Heat Output

Efficiency (fuel to steam) (*3)

1,725 LB/HR

1,674,000 BTU/HR

Heating Surface Area

Operational Weight T Shipping Weight

192.4 fT2

3710 LBS

4,140 LBS

Width

Length

Height

40 in. (50 in.)

96 in. (1 19 in.)

'- 103 in. (147 in.)

t

1 OOHP 150HP 200HP

170 PSIG MAWP, 150 PSIG Maximum Operating (15 PSIG MAWP)

3,450 LB/HR

3,348,000 BTU/HR

5,175LB/HR

5,022,000 BTU/HR

6,900 LBIHR

6,695,000 BTUIHR

85% (80% without Economizer)

269.0 fT2

6,070 LBS

5,930 LBS T

388.2 fT2 387.7 FTI

8.620 LB518.620 LBS

7,920 LBS r 7,950 LBS

Dimensions Given are Approximate __

38 in. (50 in.)

124 in. (155 in.)

111 in. (161 in.)

43 in. (65 in.) 43 in.(65 in.)

139 in. (142 _in...:...l_,__1_39_ in. (142 in.)

126in.(131 ~ 126in.(131 in.)

Proprietary Forced Draft, Step Fired Modulation Hi-Low-Off

Electric Spark Ignited. Interrupted Gas Pilot -----

208, 230, 460, 575V. 3 phase, 60Hz

10,350 LB/HR

10,050,000 BTU/HR

87%

611 fT2

10.940 LBS

11,050 LBS

63 in.

153 in.

127 in. 4 Position Step Bur~~~ (Hi-Low-IgnitiOn-Orr~

J Combustion System

Ignition System

Power Supply

Max. Electrical Consumption

Fuel Type (*4)

Gas Consumption (*5)

Gas Supply Pressure !-----

6.5 KVA (5.0 KVA) 13.3 KVA (10.9 KVA) 22.1 KVA 24.3 KVA (19.0 KVA) refer to Installation manual1.8

Natural Gas or Propane (3-5 PSIG)

1,960 SCFH 3,920 SCFH 5,880 SCFH 7,850 SCFH 11,500 SCFH

Main Steam Outlet Valve

Safety Valve Outlet(*6) 1---- -

Main Water Inlet >-------

Fuel Gas Inlet

Automatic Surface Slowdown

Manual Blowdown r------

- Chimney Diameter (ID)

Flame Detector

Pressure Control

Liquid Volume Control

Overheat Protection

2 in. (4 in.)

One 1 '12 in.

3/• in.

1 'h in.

12 in.

Note: *1 Available 49 and 199 BHP rating for L.A. area.

3-5 PSIG Natural Gas or Propane

One lfa in.

Two1 in.

1 in.

2 in.

3 in. (8 in.)

One2 'h in.

Ultraviolet Flame Eye Sensor

Adjustable Pressure Transducer and Switch

Electric Conductivity ~ype

low Water Cut Off & Thermocouple

*2 Equivalent output calculated from and at 212•F (1oo·q feed water at 212°F (1oo•q steam. *3 Thermal Efficiencies are based on high heating values of fuels and 68"F (20"Q feed water. *4 ULand c-UL approved for natural gas or propane. *5 Gas consumption based on natural gas with high heating 1004 BTU/SCF. *6 Safety valve outlet size may change depending on the pressure setting.

4in.

Two 2 '12 in.

1 'hin.

2 'h in.

Two '!t in.

One 1 in. & One 1 1/ • in.

20 in.

"S" - Economizer " G" - Natural Gas or Propane Fired "(L)" - Low Pressure

*7 See Miura's Ml System brochure for more on how the new LX-300 zero-side-clearance layout offers t he highest system capacity per square foot in the industry.

Additional Notes: 1 All Miura steam boilers are fully packaged and test fired at factory. 2 Built to meet or exceed UL & ASME standards in U.S.A.; c-UL & B-51 standards in Canada. 3 Low pressure steam is available in 50, 100 and 200 BHP only. 4 california Low NOx modei(LXl OOSGI, LX150SGI, LX200SGI, LX-300SGI) available. 5 High pressure model (300psi), LXH200 , LXH300 is available.

[!1~,-'".Y.; ... ~ [!] :Jor..' -:;!.G. Jf f~ Virtual Stan:-Up Video

• tr~· ··:- ·.;~i.f.l ~:.o-tt:.~ ·: _·:·~ ) • r::'1 : AI: . . J L:J ..... ..!;''Fi ,.. • : lVI lURA

USA: 1-888-309-5574 • Canada: 1-800-666-2182 • www.miuraboiler.com

Worldwide Headquarters • Japan: +81-89-979-7123 • www.miuraz.co.jp

Facilities located in: USA • Canada • Japan • China • Korea • Taiwan

• Miura Steam is Engineered for Greater Efficiency, Lower Costs, and Reduced Environmental Impact.

LX2EN11

• lVII U RA

Propane • June 25, 2014

Emissions for Propane Boiler ModeiLX(L)-200 SGI

Miura certifies that the LX(l)-200 SGI boiler model will achieve the emission levels as shown below for

NOx, CO, C02, VOC, 502 and PM. The emission levels shown are based upon the boiler being installed

correctly, properly maintained, and operated under normal loading conditions within the designed

parameters. The boiler may need to be adjusted at the initial start-up by a Miura certified technician .

After the initial setup, it is the responsibility of the owner to test the boiler regular ly to insure the

boiler is tuned and operating correctly.

Special low NOx burner and controls are engineered and manufactred by Miura

NOx:

Measured

Dry flue gas volume

Molecular mass

Constant

Calculation

Measured

Dry flue gas volume

Molecular mass

Constant

Calculation

C02:

Fuel Input

EPA Emission Factor

Calculation

VOC: Fuel Input

High Heating Value

EPA Emission Factor

Calculation

502:

Fuel Input

EPA Emission Factor

Calcu lation

12 ppm (propane)

72100 scfh

46.1

2.595E-09

{72100 scfh) X {12 ppm) X (46.1) X (2 .595E-9) = 0.103 lbs/hr

SO ppm {propane)

72100 scfh

28

2.595E-09

(72100 scfh) x (50 ppm) X (28) x (2.595E-9) = 0.262 lbs/hr

7.089 MMBtu/hr

136.6 lbs/MMbtu (propane)

(7.089 MMBtu/hr) x (136.6 lbs/MMbtu) = 968 lbs/hr

No EPA Factor

7.089 MMBtu/hr

0.001093 lbs/MMbtu (propane) (7.089 MMBtu/hr) x (0.001093 lbs/MMbtu) = 0.0077 lbs/hr

Fuel Input

EPA Emission Factor Calculation

• lVI lURA

• 7.089 MMBtu/hr

0.00765 lbs/MMbtu (propane)

(7.089 MMBtu/hr) x (0.00765 lbs/MMbtu) = 0.0541bs/hr

The NOx and CO are corrected to 3% 02 based on propane combustion

The dry flue gas volume was corrected to 3% 02 at 68 degrees F

Reference: AP-42, Table 1.5-1 Emissions Factors, U.S Environment Protection Agency

The table below shows the emissions based on operating one LX(L)-200 SGI at 100% load for 24 hours a day, 91 days per quarter, and 365 days per year.

Emission Data lbs/hr lbs/qtr tons/year lbs/MMBtu

NOx 0.103 226 0.453 0.0146

co 0.262 572 1.147 0.0369 C02 968 2,110,000 4241 137

voc 0.000 0.0 0.000 0.0000 502 0.008 16.92 0.034 0.0011 PM 0.054 118.4 0.238 0.0077

" " ,,

" " " ( 19 \ HI ~7 \U

....

" '"

' BARNUM ~-'MECHANICAL INC.

I .... ... ~ .. ~ .. ik. ·IIUI

(4) NEW BOILERS (2) FUTURE BOILERS~

BOILER ROOM 312

1 1

~! ~ t + 'II

CRYSTAL GE.YSER

o c •,:JIII!;,.=~~&O nu

APPLICATION TO THE AIR DISTRICT FOR AN AUTHORITY TO

CONSTRUCT AND PERMIT TO OPERATE FOR GENERATORS

WT1216151006RDD

CH2M Redding Office 2525 Airpark Drive Redding, CA 96001 O +1 530 243 5831 F +1 530 243-1654 www.ch2m.com

Mr. Patrick Griffin County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097

December 17, 2015

Subject: Permit Application for an Authority to Construct/Permit to Operate for Three Propane-powered Electricity Generators at Crystal Geyser Water Company, Mt. Shasta, California Facility

Dear Mr. Griffin

This letter presents a permit application for an Authority to Construct/Permit to Operate for three new electricity generators at the Crystal Geyser Water Company (CGWC) facility located at 210 Ski Village Drive near Mt. Shasta, Siskiyou County, California. This application package includes the following:

• Siskiyou County Air Pollution Control District (SCAPCD) permit application form, including the Power Generators Supplemental Application form and project facility map (Attachment 1)

• Generator specification and emissions data (Attachment 2)

• Engine emission calculations (Attachment 3)

• A check in the amount of $150 ($50 each), in accordance with Rule 3.1

Additionally, this letter provides a rule compliance evaluation, which demonstrates that the proposed equipment operation would comply with applicable federal regulations and state and local rules.

Project and Equipment Description The CGWC facility is located in the County of Siskiyou outside the City Limits of Mt. Shasta, adjacent to the northern portion of the city, on the southwestern flank of Mt. Shasta; it is bordered by Ski Village Drive to the north, Mount Shasta Boulevard to the west, McCloud Railroad to the south, and low-density residential development to the east.

CGWC proposes to install three new generators to supplement the electricity demand for facility operations. These three generators are identical and would be powered by propane fuel. Key information about the generators is listed below:

• Generator Model: Caterpillar SR4-B, rated at 376 kilowatts • Engine Model: CAT G3412C LE, rated at 573 horsepower (hp) • Emission Control: DCL catalyst Model 2-DC63F-8 CC

With the proposed emission control, volatile organic compounds (VOC) and carbon monoxide (CO) emissions are guaranteed to meet the U.S. Environmental Protection Agency New Source Performance

Mr. Patrick Griffin Page 2 December 17, 2015

WT1216151006RDD

Standard for Stationary Spark Ignition Internal Combustion Engines emission standards in 40 Code of Federal Regulations (CFR) Part 60, Subpart JJJJ (Subpart JJJJ).

Construction and installation of the generators is expected to start in May 2016. This application assumes emissions based on operating the generators 24 hours per day for 365 days per year. Bottling operations by CGWC will likely involve significantly less generator use, because the bottling facility will operate in shifts of less than 24 hours per day. In addition, the supplemental power requirements of the bottling facility are an estimate and cannot be definitively determined at this time. Actual operations may, therefore, only require the use of one or two generators rather than all three. The three generators will be contained in a building similar to that shown on page 10 of Attachment 2.

Emission Evaluation The detailed propane engine emission data are shown in Attachment 2 for CO, nitrogen oxides (NOx), and VOCs. As previously discussed, each generator engine will be equipped with DCL catalyst Model 2-DC63F-8 CC. Table 1 summarizes the emission factors, and the hourly, daily, and annual emissions of each engine. Detailed emission calculations are provided in Attachment 3.

Table 1 Generator Emission Summary

Generator Emissions Summary – Each Engine a

Emission

Emission Factor b Hourly Daily Annual

g/hp-hr lb/hour lb/day ton/year

CO 2.00 2.53 60.63 11.07

NOx 1.00 1.26 30.32 5.53

VOC 0.70 0.88 21.22 3.87

Generator Emissions Summary – Total of Three Engines a

Emission

Emission Factor b Hourly Daily Annual

g/hp-hr lb/hour lb/day ton/year

CO 2.00 7.58 181.90 33.20

NOx 1.00 3.79 90.95 16.60

VOC 0.70 2.65 63.67 11.62

a To be conservative, emissions were calculated based on 100% load. b Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst (Attachment 2)

Notes:

g/hp-hr = grams per horsepower hour lb/hour = pounds per hour lb/day = pounds per day ton/year = tons per year

For emission calculation purposes, the emissions from the engine were conservatively estimated based on 100 percent load during operation. Engine emission factors for VOC and CO were based on the guaranteed emission rates with the oxidation catalyst, as shown in Attachment 2.


WT1216151006RDD

Because the engine is propane powered, emissions of other pollutants, such as sulfur dioxide (SO2), particulate matter (PM), and lead, would be negligible.

Rule Compliance Evaluation Applicable SCAPCD Rules Regulation IV: Prohibitions. Regulation IV includes the following rules that are applicable to the proposed generators:

• Rule 4-1: Visible Emissions • Rule 4-2: Nuisance • Rule 4-4: Specific Air Contaminants

The proposed generators would be powered by propane engines with negligible PM and SO2 emissions. VOC, CO, and NOx emissions would be below the limits set forth in Rule 4-4. Operation of the generators would comply with SCAPCD rules and following manufacturer’s specifications and procedures. Therefore, operation of the generators would not cause emissions or nuisance that violate Rule 4-1, Rule 4-2, or Rule 4-4 requirements.

Regulation VI: New Source Siting. Regulation VI includes the new source review rules for new or modified emission sources:

• Rule 6-1: Construction Permit Standards for Criteria Pollutants

Rule 6-1 requires best available control technology (BACT) and offsets emissions from a new or modified emission unit under either of the following conditions:

– A net increase in emissions of 250 pounds or more during any day of any pollutant for which there is a national ambient air quality standard (excluding CO) or any precursor of such a pollutant

– A net increase in emissions of 2,500 pounds or more of CO during any day

The proposed emissions from the generators would be negligible for PM and SO2. As shown in Table 1, NOx and VOC emissions would be less than 250 lb/day, and CO emissions would be less than 2,500 lb/day. Therefore, the proposed generators would not trigger BACT or offset emissions under Rule 6-1.

• Rule 6-4: Construction Permit Standards for Hazardous Air Pollutants

Rule 6-4 applies to major source of hazardous air pollutants (HAP) that has more than 25 ton/year of total HAP emissions, or 10 ton/year of any single HAP. Because the facility is not a HAP major source, Rule 6-4 does not apply.

U.S. Environmental Protection Agency New Source Performance Standards 40 CFR Part 60 Subpart JJJJ. The proposed generators would be powered by propane engines. Therefore, they are subject to 40 CFR Part 60, Subpart JJJJ – Standards of Performance for Stationary Spark Ignition Internal Combustion Engines. The applicable emission standards of Subpart JJJJ and the manufacturer’s guarantee of engine emissions are summarized in Table 2. As shown in Table 2, the proposed propane engines emissions would meet the Subpart JJJJ emission standards.


WT1216151006RDD

Table 2 Comparison of Engine Emissions to Subpart JJJJ Standards

Subpart JJJJ Standard or Engine Emission VOC NOx CO

Subpart JJJJ Standards (ppm at 15% O2) 60 82 270

Subpart JJJJ Standards (g/hp-hr) 0.70 1.00 2.00

Engine G3412C LE emissions (ppm at 15% O2)a <60 <82 <270

Engine G3412C emissions (g/hp-hr) <0.70 <1.00 <2.00

a Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst

Notes:

< = less than O2 = oxygen ppm = parts per million

If you have questions or need additional information, please contact Peter Rude at (530) 229-3396 or Hong Zhuang at (714) 435-6349. Regards, CH2M HILL, Inc. Hong Zhuang Peter H. Rude, P.E Project Engineer Project Manager

Attachment 1 SCAPCD Permit Application Form and Power Generators Supplemental Application Forms


/

County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097 Phone#: (530) 841-4029: 841-4031 Fax#: (530) 842-6690

Permit Application For: -New Construction 0

D D 0

Authority To Construct (ATC) Authority To Construct (ATC) Authority To Construct (ATC) Permit to Operate CPTO)

-Mod.ification of Emission Unit to a Valid P'T'O/A'l'C

-Change of Location

-ownership change

L PERMIT TO DE ISSUED To: Crystal Geyser Water Company

2. MA!UNG ADDREss:

STREET/P.O Box: 501 Washington Street

Crrv: Calistoga S'rAm: California ZIP ConE: 94515

3. LoCATION WHERE THE EQUIPMENT V.IJLL BE OPERATED: Within 1,000 ft. of a school? STREET 21 0 Ski Village Drive CI'IY Mt Shasta 0 Yes0 No

SJ.C. Code of Facility: 2086 SEcrroN: 9 ToWNslill': 40N RANGE: 04W

Proposed install date: May 2016 Proposed

4. GENERAL NATURE OF BUSINESs: Beverage Manufacturer Completion date: June 2016

5. D ESCRIPTION OF EQUIPMENT OR MODll<'lCATION F OR WHICH APPLICATION IS MADE: UNCLUDE ADDITIONAL

S1IEETSASNESSECCARY) Installation of three propane generators, Caterpillar G3412C. See application for details

6. HAVEYOUEVERAPPLIED FORANATCORPTO IN S ISKIYOU COUNTY?0 N dZJ YES, It' YES, P ERMIT#: 101515-BH-1

7. Is THIS PROPERTY zoNED PROPERLY FOR THIS PERMIT? D No [Z]YES, IF YES, ZONE con E#: M-H

8. Is THE EQUIPMENT REGISTRED WITH CARB.? 0 No D YEs, IF YEs, REa.#:

9. TYPE OF ORGANIZATioN: CoRPoRATION, 0 PARTNERSHIP, O INDrvwuAL, O GoVERNMENT AGENCY, D

10. TYPE OR PRINT NAME OF APPLICANT: Richard Weklych TITLE OF APPLICANT: EVP manufacturing

!!. SlGNAT REOF7.L D ATE: PHONE#: 707-972-0500

~~171~ FAx#:

//tZU. £. E -MAIL: RichardW@crystalgeyser. com

v A $50.00 filing fee must accompany each application/s (District rule 3.1 Permit Fees) Date paid:



1 of 1 G:\DATA\Air PoUution\Forms and Templates

Siskiyou County APCDGenerator Application

County of SiskiyouAir Pollution Control District

Power Generators Supplemental Application Form

A. Use one application form for each permit unit of basic equipment and air pollution controlequipment. This may include a single or multi-component system.

B. This application must accompany a Permit Application form.C. Each application must be filled out completely and accompanied by adequate plans and operating

characteristics.D. A responsible member of the organization that is to operate the equipment must sign each

application.

LEGAL OWNER

Name:

Address:

City/Zip:

Phone/Fax:

e-mail:

OPERATOR

Name (Business License Name):

Address (Physical address):

City/Zip:

Phone/Fax:

e-mail:

Physical location (address) of the generator:

1 of 3G:\DATA\Air Pollution\Forms and Templates

501 Washington Street

Crystal Geyser Water Company

Calistoga, California, 94515

707-972-0500

[email protected]




707-972-0500

[email protected]

Generator 1 210 Ski Village Drive Mt. Shasta California, CA 96067

Siskiyou County APCD Generator Application

EQUIPMENT DESCRIPTION:Manufacturing Specification sheets (attach if any)

Manufacture:

Model #:

Serial #:

Horsepower (hp):

Btu/hour:

Fuel consumption gals/hr:

Year engine was manufactured:

Fuel Type:

PRODUCTION INFORMATION:1 Data needed for back up generators only

Maximum production output (kw-hrs):

Average production output (kw-hrs):

Estimated hours of operation per day:

Estimated days of operation per year:1Maximum hours needed for testing (Yearly):1Best hours needed for maintenance :

PORTABLE REGISTRATION INFORMATION:Attach all state registration information if applicable.

Registration Number:

CRITERIA EMISSION DATA:

CO (lbs/hr @ 50% and 100% power):

NOx (lbs/hr @ 50% and 100% power):

SOx (lbs/hr @ 50% and 100% power):

PM10 (lbs/hr @ 50% and 100% power):

Lead (lbs/hr @ 50% and 100% power):


Propane

Generator Model SR4-B, Engine Model: G3412C LE

Caterpillar

To be determined

35.7 gallons/hour @ 50% load, 59.7 gallons/hour @ 100% load

2015

573

3,293,760 (annual)

3,293,760 (annual)

24

365

NA

1.26 lb/hr @50%, 2.53 lb/hr @100% power

0.63 lb/hr @ 50%, 1.26 lb/hr @ 100% power

Negligible

Negligible

Negligible


LOCATION DATAEQUIPMENT

Drawing or sketch of proposed layout, showing the generator relative to buildings, streets, houses, etc.(This part can be faxed back to the District on a separate sheet)

Distance (in feet) from the generator emission point to the closest:

School ft. :

Hospital ft.:

Daycare ft.:

Resident ft. :


700

2,700

3,200

3,500







application.

LEGAL OWNER

Name:

Address:

City/Zip:

Phone/Fax:

e-mail:

OPERATOR



City/Zip:

Phone/Fax:

e-mail:






707-972-0500

[email protected]




707-972-0500

[email protected]




Manufacture:

Model #:

Serial #:

Horsepower (hp):

Btu/hour:



Fuel Type:















Propane


Caterpillar

To be determined


2015

573

3,293,760 (annual)

3,293,760 (annual)

24

365

NA

1.26 lb/hr @50%, 2.53 lb/hr @100% power

0.63 lb/hr @ 50%, 1.26 lb/hr @ 100% power

Negligible

Negligible

Negligible





School ft. :

Hospital ft.:

Daycare ft.:

Resident ft. :


700

2,700

3,200

3,500







application.

LEGAL OWNER

Name:

Address:

City/Zip:

Phone/Fax:

e-mail:

OPERATOR



City/Zip:

Phone/Fax:

e-mail:






707-972-0500

[email protected]




707-972-0500

[email protected]




Manufacture:

Model #:

Serial #:

Horsepower (hp):

Btu/hour:



Fuel Type:















Propane


Caterpillar

To be determined


2015

573

3,293,760 (annual)

3,293,760 (annual)

24

365

NA

1.26 lb/hr @50%, 2.53 lb/hr @100% power

0.63 lb/hr @ 50%, 1.26 lb/hr @ 100% power

Negligible

Negligible

Negligible





School ft. :

Hospital ft.:

Daycare ft.:

Resident ft. :


700

2,700

3,200

3,500

Aerial photo source: Google ©2014, modified by CH2M HILL.

Legend

CGWC Property Line

WBG031814043631RDD CG_LocationData_Figure1_V3.ai cmont 12/15/15

Figure 1: Location DataPower Generators SupplementalApplication Form for County of SiskiyouAir Pollution Control DistrictCrystal Geyser Water Company

North

0 300

Approximate scale in feet

100 200 400 500

FIRESUPPRESSION

TANK

DOMESTICWELL AND

PUMP HOUSE

SKI VILLAGE DR.

CGWCBOTTLING PLANT

BUTTE AVE.

SHASTA AVE.

N. M

T. SH

AS

TA B

LVD

.

MCCLOUD RAILROAD

3 PROPANEPOWER GENERATORS

PROPANETANK

Attachment 2 Generator Specifications and Emission Data

G A SG E N E R A T O R S E T

STANDBY 375 ekWCONTINUOUS

375 ekW60 Hz

Caterpillar is leading the power generationmarketplace with Power Solutions engineeredto deliver unmatched flexibility, expandability,reliability, and cost-effectiveness.

FEATURES

FULL RANGE OF ATTACHMENTS

● Wide range of bolt-on system expansionattachments, factory designed and tested

SINGLE-SOURCE SUPPLIER

● Fully Prototype Tested with certified torsionalvibration analysis available

WORLDWIDE PRODUCT SUPPORT

● Worldwide parts availability through theCaterpillar dealer network

● With over 1,200 dealer outlets operatingin 166 countries, you’re never far fromthe Caterpillar part you need.

● 99.5% of parts orders filled within 48 hours.The best product support record in theindustry.

● Caterpillar dealer service technicians aretrained to service every aspect of your electricpower generation system.

● Preventive maintenance agreements● The Cat Scheduled Oil Sampling (S•O•SSM)

program cost effectively detects internal enginecomponent condition, even the presence ofunwanted fluids and combustion by-products

CAT® G3412C LE GAS ENGINE

● Reliable, rugged, durable design● Field-proven in thousands of applications

worldwide● Low pressure gas

CAT SR4B GENERATOR

● Designed to match performance and outputcharacteristics of Caterpillar engines

● Optimum winding pitch for minimum totalharmonic distortion and maximum efficiency

● Segregated AC/DC, low voltage accessorybox provides single point access toaccessory connections

CAT CONTROL PANELS

● Two levels of controls, designed to meetindividual customer needs:

EMCP II provides digital monitoring, metering,and protectionEMCP II+ provides EMCP II features alongwith full-featured power metering andprotective relaying

W H E R E T H E W O R L D T U R N S F O R P O W E R

CAT SR4B GENERATOR

Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592Type . . . . . . . . . . . . . . . . Self excited, static regulated, brushlessConstruction . . . . . . . . . . . . . . . . . . Single bearing, close coupledThree phase . . . . . . . . . . . . . . . . . . . . . . . . . 12 lead reconnectableInsulation . . . . . . Class H with tropicalization and antiabrasionIP rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drip proof 22Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pilot shaftOverspeed capability

Prototype tested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150%Production tested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125%

Wave form. . . . . . . . . . . . . . . . . . . . . . . . . . Less than 5% deviationParalleling capability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . StandardVoltage regulator . . . . . 3-phasing sensing with Volts-per-HertzVoltage regulation . . . . . . . . . . . Less than ± 1/2% (steady state)

Less than ± 1% (no load to full load)Voltage gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AutomaticTelephone Influence Factor (TIF). . . . . . . . . . . . . . . . Less than 50Harmonic Distortion (THD) . . . . . . . . . . . . . . . . . . . . Less than 5%

CAT ENGINE

G3412C LE, 4-stroke-cycle, SCACBore – mm (in) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 (5.4)Stroke – mm (in) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 (6.0)Displacement – L (cu in) . . . . . . . . . . . . . . . . . . . . . . . . . 27.0 (1649)Compression ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4:1Aspiration . . . . . . . . . . . . . . . . . . . . . . . Turbocharged-AftercooledIgnition system . . . . . . . . . . . . . . . . . Cat Electronic Ignition (EIS)Governor type . . . . . . . . . . . . . . . . . . . . . . . . . . . Woodward 2301A

CAT CONTROL PANEL

24 Volt DC Control

NEMA 1, IP22 enclosureElectrically dead frontLockable hinged doorGenerator instruments meet ANSI C-39-1Terminal box mountedSingle location customer connector point

Consult your Caterpillar dealer for available voltages.

SPECIFICATIONS

S T A N D B Y 3 7 5 e k WC O N T I N U O U S 3 7 5 e k W6 0 H z

FACTORY INSTALLED STANDARD & OPTIONAL EQUIPMENT

System Standard Optional

Air Inlet Single element canister type air cleanerService indicator

Cooling Radiator with guard Jacket water coolant heater with shutoff valvesCoolant drain lines with valves Radiator removalFan and belt guardsCaterpillar CoolantLow coolant level sensors

Exhaust Stainless steel exhaust flex with 15 dBA mufflerweld outlet flange

Fuel Gas pressure regulatorLow pressure fuel systemEnergize To Run (ETR) gas shutoff valve

Generator Self excited Permanent magnet excitedClass H insulation Digital Voltage RegulatorClass F temperature rise Digital Voltage Regulator with KVAR/PF control

(105° C continuous/130° C standby) Anti-condensation space heaterVR6 Voltage Regulator, 3-phase sensing, Oversize & premium generators

with reactive droop Circuit breakers, UL, 3 pole with shunt trip2:1 Volts/Hz or 1:1 Volts/Hz Multiple breaker capabilityBus bar terminationExtension box

Governor 2301A speed control with EG3P actuator Electronic load sharingIgnition Electronic Ignition System (EIS)Control Panels EMCP II EMCP II+

Customer Communication ModuleLocal alarm & remote annunciator modules

Lube Lubricating oil and filter Manual sump pumpOil drain line with valveFumes disposal

Mounting Wide baseLinear vibration isolators between base

and engine-generatorStarting/Charging 35 amp charging alternator Battery chargers, 5 & 10 amp

24 volt starting motor Oversize batteriesBatteries with rack and cablesBattery disconnect switch

General Automatic Transfer Switches (ATS)Floor standing circuit breakers

2

S T A N D B Y 3 7 5 e k WC O N T I N U O U S 3 7 5 e k W6 0 H z

Note: Do not use for installation design.See general dimension drawingsfor detail (Drawing #207-4503).

Package Dimensions

Length 4540 mm 178.74 in

Width 2238 mm 88.11 in

Height 2678.5 mm 105.45 in

Shipping Weight 6356 kg 14,000 lb

www.CAT-ElectricPower.com

TMI Reference No.: DM5443, DM5444 © 2001 CaterpillarAll rights reserved.

U.S. sourced Printed in U.S.A.

LEHE1432 (06-01) Materials and specifications are subject to change without notice.The International System of Units (SI) is used in this publication.

STANDBY/CONTINUOUS POWER GENERATOR SET PACKAGE — TOP VIEW

STANDBY/CONTINUOUS POWER GENERATOR SET PACKAGE — SIDE VIEW

Crystal Geyser

G3412C LE

Propane Fueled

5703

530

376

7.10

OUTPUT

Emission [ppm] at 15 %O2 NOx < 82 82

Emission [ppm] at 15 %O2 CO < 270 270

Emission [ppm] at 15 %O2 THC

Emission [ppm] at 15 %O2 NMHC (VOC) < 60 60

Emission [ppm] at 15 %O2 HCHO

Emission [ppm] at 15 %O2 Particles

Project Name: Crystal Geyser

Engine: G3412C LE, 1800rpm, 32C Air Inlet, 1189m

Fuel gas: Propane (HD‐5) with Oxidizing Catalyst G15‐3400‐197

INPUT

EPA 40 CFR Part

60 Subpart jjjj

requirements

Dry exhaust gas flow [lbm/hr]

Engine mechanical power [bhp]

Genset electrical power [ekW]

Exhaust volume flow dry O2 [%]

Peterson Power Systems

2828 Teagarden Street

San Leandro, CA 94577

Crystal Geyser

G3412C LE

Emissions Data 12/16/2015

G3412C GAS ENGINE SITE SPECIFIC TECHNICAL DATAPACKAGED GENSET APPLICATION Crystal GeyserENGINE SPEED (rpm): 1800 RATING STRATEGY: STANDARDCOMPRESSION RATIO: 8.5 RATING LEVEL: CONTINUOUSAFTERCOOLER TYPE: SCAC FUEL SYSTEM: LPG IMPCOAFTERCOOLER WATER INLET (°F): 130 WITH CUSTOMER SUPPLIED AIR FUEL RATIO CONTROLJACKET WATER OUTLET (°F): 210 SITE CONDITIONS:ASPIRATION: TA FUEL: G15-3400-197 (00)COOLING SYSTEM: JW+OC, AC FUEL PRESSURE RANGE(psig): 1.5-5.0CONTROL SYSTEM: EIS FUEL METHANE NUMBER: 32.9EXHAUST MANIFOLD: WC FUEL LHV (Btu/scf): 2299COMBUSTION: LOW EMISSION ALTITUDE(ft): 3100NOx EMISSION LEVEL (g/bhp-hr NOx): 1.0 MAXIMUM INLET AIR TEMPERATURE(°F): 90FAN POWER (bhp): 42 STANDARD RATED POWER: 637 bhp@1800rpmSET POINT TIMING: 21 POWER FACTOR: 1.0

VOLTAGE(V): 480-480

MAXIMUMRATING

SITE RATING AT MAXIMUMINLET AIR TEMPERATURE

RATING NOTES LOAD 100% 100% 75% 52% PACKAGE POWER (WITH FAN) (1)(2) ekW 376 376 282 196

PACKAGE POWER (WITH FAN) (1)(2) kVA 376 376 282 196

ENGINE POWER (WITHOUT FAN) (2) bhp 573 573 440 319

INLET AIR TEMPERATURE °F 90 90 90 90

GENERATOR EFFICIENCY (1) % 94.7 94.7 94.7 94.7

PACKAGE EFFICIENCY (ISO 3046/1) (3) % 26.0 26.0 24.7 22.6

THERMAL EFFICIENCY (4) % 54.5 54.5 56.3 59.3

TOTAL EFFICIENCY (5) % 80.5 80.5 81.0 81.9

ENGINE DATA PACKAGE FUEL CONSUMPTION (ISO 3046/1) (6) Btu/ekW-hr 13140 13140 13833 15129 PACKAGE FUEL CONSUMPTION (NOMINAL) (6) Btu/ekW-hr 13395 13395 14101 15423 ENGINE FUEL CONSUMPTION (NOMINAL) (6) Btu/bhp-hr 8773 8773 9018 9470 AIR FLOW (@inlet air temp, 14.7 psia) (WET) (7)(8) ft3/min 1258 1258 981 721

AIR FLOW (WET) (7)(8) lb/hr 5452 5452 4251 3125

FUEL FLOW (60ºF, 14.7 psia) scfm 36 36 29 22

INLET MANIFOLD PRESSURE (9) in Hg(abs) 58.9 58.9 46.0 35.2

EXHAUST TEMPERATURE - ENGINE OUTLET (10) °F 909 909 880 865

EXHAUST GAS FLOW (@engine outlet temp, 14.5psia)

(WET) (11)(8) ft3/min 3369 3369 2573 1875

EXHAUST GAS MASS FLOW (WET) (11)(8) lb/hr 5703 5703 4449 3276

EMISSIONS DATA - ENGINE OUT NOx (as NO2) (12)(13) g/bhp-hr 1.00 1.00 1.00 1.00

CO (12)(13) g/bhp-hr 2.91 2.91 3.05 3.17

THC (mol. wt. of 15.84) (12)(13) g/bhp-hr 2.05 2.05 2.47 2.86

NMHC (mol. wt. of 15.84) (12)(13) g/bhp-hr 2.05 2.05 2.47 2.86

NMNEHC (VOCs) (mol. wt. of 15.84) (12)(13)(14) g/bhp-hr 2.05 2.05 2.47 2.86

HCHO (Formaldehyde) (12)(13) g/bhp-hr 0.29 0.29 0.31 0.34

CO2 (12)(13) g/bhp-hr 597 597 597 611

EXHAUST OXYGEN (12)(15) % DRY 7.1 7.1 7.0 7.0

HEAT REJECTION LHV INPUT (16) Btu/min 83831 83831 66189 50271 HEAT REJ. TO JACKET WATER (JW) (17) Btu/min 26711 26711 22663 18864 HEAT REJ. TO ATMOSPHERE (17) Btu/min 3353 3353 2648 2011 HEAT REJ. TO LUBE OIL (OC) (17) Btu/min 4224 4224 3584 2983 HEAT REJECTION TO EXHAUST (LHV TO 350°F) (17) Btu/min 14450 14450 10678 7656 HEAT REJ. TO AFTERCOOLER (AC) (17)(18) Btu/min 3303 3303 2002 804

COOLING SYSTEM SIZING CRITERIA TOTAL JACKET WATER CIRCUIT (JW+OC) (19) Btu/min 34450 34450 TOTAL AFTERCOOLER CIRCUIT (AC) (19) Btu/min 4607 4607 HEAT REJECTION TO EXHAUST (LHV TO 350°F) (19) Btu/min 15895 15895 A cooling system safety factor of 0% has been added to the cooling system sizing criteria.

MINIMUM HEAT RECOVERY TOTAL JACKET WATER CIRCUIT (JW+OC) (20) Btu/min 27419 27419 TOTAL AFTERCOOLER CIRCUIT (AC) (20) Btu/min 3138 3138 HEAT REJECTION TO EXHAUST(LHV TO 350°F) (20) Btu/min 11986 11986

CONDITIONS AND DEFINITIONSEngine rating obtained and presented in accordance with ISO 3046/1, adjusted for fuel, site altitude and site inlet air temperature. 100% rating at maximum inlet air temperature is the maximum enginecapability for the specified fuel at site altitude and maximum site inlet air temperature. Maximum rating is the maximum capability at the specified aftercooler inlet temperature for the specified fuel atsite altitude and reduced inlet air temperature. Lowest load point is the lowest continuous duty operating load allowed. No overload permitted at rating shown.

For notes information consult page three.***WARNINGS ISSUED FOR THIS RATING CONSULT PAGE 3***

PREPARED BY:Data generated by Data Maintenance Utility Version 5.05.00Special Rating Request G15-3400-197 (00), Printed 20Nov2015 Page 1 of 4

G3412C GAS ENGINE SITE SPECIFIC TECHNICAL DATAPACKAGED GENSET APPLICATION Crystal Geyser


C!TERPILLAR"

Engine Power vs.lnlet Air Temperature Data represents temperature sweep at 31 00 ft and 1800 rpm

30 40 50 60 70 80 90 1 00 11 0 120 130 Air Temperature, •F

D No Hating Available Range for Site Conditions

D Continuous Opera ting Range for Site Conditions

• Low Load Intermittent Operating Range


NOTES1. Generator efficiencies, power factor, and voltage are based on specified generator. [Package Power (ekW) is calculated as: (Engine Power (bkW) - Fan Power(bkW)) x Generator Efficiency], [Package Power (kVA) is calculated as: (Engine Power (bkW) - Fan Power (bkW)) x Generator Efficiency / Power Factor]

2. Rating is with two engine driven water pumps. Tolerance is (+)3, (-)0% of full load.

3. Package Effieciency published in accordance with ISO 3046/1.

4. Thermal Efficiency is calculated based on energy recovery from the jacket water, lube oil, and exhaust to 350ºF with engine operation at ISO 3046/1 PackageEfficiency, and assumes unburned fuel is converted in an oxidation catalyst.

5. Total efficiency is calculated as: Package Efficiency + Thermal Efficiency. Tolerance is ±10% of full load data.

6. ISO 3046/1 Package fuel consumption tolerance is (+)5, (-)0% at the specified power factor. Nominal package and engine fuel consumption tolerance is ± 3.0% of fullload data at the specified power factor.

7. Air flow value is on a 'wet' basis. Flow is a nominal value with a tolerance of ± 5 %.

8. Inlet and Exhaust Restrictions must not exceed A&I limits based on full load flow rates from the standard technical data sheet.

9. Inlet manifold pressure is a nominal value with a tolerance of ± 5 %.

10. Exhaust temperature is a nominal value with a tolerance of (+)63°F, (-)54°F.

11. Exhaust flow value is on a "wet" basis. Flow is a nominal value with a tolerance of ± 6 %.

12. Emissions data is at engine exhaust flange prior to any after treatment.

13. Emission values are based on engine operating at steady state conditions, adjusted to the specified NOx level at 100% load. Fuel methane number cannot varymore than ± 3. NOx values are set points and will vary with operating conditions. All other emission values listed are higher than nominal levels to allow forinstrumentation, measurement, and engine-to-engine variations. They indicate "Not to Exceed" values. THC, NMHC, and NMNEHC do not include aldehydes. PartLoad data requires customer supplied air fuel ratio control.

14. VOCs - Volatile organic compounds as defined in US EPA 40 CFR 60, subpart JJJJ

15. Exhaust Oxygen level is the result of adjusting the engine to operate at the specified NOx level. Tolerance is ± 0.5.

16. LHV rate tolerance is ± 3.0%.

17. Heat rejection values are representative of site conditions. Tolerances, based on treated water, are ± 10% for jacket water circuit, ± 50% for atmosphere, ± 20% forlube oil circuit, ± 10% for exhaust, and ± 5% for aftercooler circuit.

18. Aftercooler heat rejection is nominal for site conditions and does not include an aftercooler heat rejection factor. Aftercooler heat rejection values at part load are forreference only.

19. Cooling system sizing criteria represent the expected maximum circuit heat rejection for the ratings at site, with applied plus tolerances. Total circuit heat rejection iscalculated using formulas referenced in the notes on the standard tech data sheet with the following qualifications. Aftercooler heat rejection data (AC) is based on thestandard rating. Jacket Water (JW) and Oil Cooler (OC) heat rejection values are based on the respective site or maximum column. Aftercooler heat rejection factors(ACHRF) are specific for the site elevation and inlet air temperature specified in the site or maximum column, referenced from the table on the standard data sheet

20. Minimum heat recovery values represent the expected minimum heat recovery for the site, with applied minus tolerances. Do not use these values for coolingsystem sizing.

WARNING(S):1. The wobbe index of the fuel is higher than or equal to 1500 Btu/scf and is lower than 1900 Btu/scf. Requires two 219-4205 carburetor valve and jet kits plus two 7E-1569 washers. Will require on-site adjustment or tuning of the fuel system to determine if washers are needed to maintain constant NOx emissions for 50 - 100% load.



Constituent Abbrev Mole % NormWater Vapor H2O 0.0000 0.0000Methane CH4 0.0000 0.0000Ethane C2H6 0.0000 0.0000

Propane C3H8 97.0000 97.0000Isobutane iso-C4H1O 0.0000 0.0000Norbutane nor-C4H1O 0.5300 0.5300

Isopentane iso-C5H12 0.0000 0.0000Norpentane nor-C5H12 0.0000 0.0000Hexane C6H14 0.0000 0.0000

Heptane C7H16 0.0000 0.0000Nitrogen N2 2.4700 2.4700Carbon Dioxide CO2 0.0000 0.0000

Hydrogen Sulfide H2S 0.0000 0.0000Carbon Monoxide CO 0.0000 0.0000Hydrogen H2 0.0000 0.0000

Oxygen O2 0.0000 0.0000Helium HE 0.0000 0.0000Neopentane neo-C5H12 0.0000 0.0000

Octane C8H18 0.0000 0.0000Nonane C9H20 0.0000 0.0000Ethylene C2H4 0.0000 0.0000Propylene C3H6 0.0000 0.0000TOTAL (Volume %) 100.0000 100.0000

Fuel Makeup: G15-3400-197 (00)

Unit of Measure: English

Calculated Fuel PropertiesCalculated Fuel PropertiesCalculated Fuel PropertiesCalculated Fuel Properties

Caterpillar Methane Number: 32.9

Lower Heating Value (Btu/scf): 2299

Higher Heating Value (Btu/scf): 2500

WOBBE Index (Btu/scf): 1870

THC: Free Inert Ratio: 39.486

Total % Inerts (% N2, CO2, He): 2.47%

RPC (%) (To 905 Btu/scf Fuel): 100%

Compressibility Factor: 0.983

Stoich A/F Ratio (Vol/Vol): 23.27

Stoich A/F Ratio (Mass/Mass): 15.40

Specific Gravity (Relative to Air): 1.511

Specific Heat Constant (K): 1.137

CONDITIONS AND DEFINITIONSCONDITIONS AND DEFINITIONSCONDITIONS AND DEFINITIONSCONDITIONS AND DEFINITIONSCaterpillar Methane Number represents the knock resistance of a gaseous fuel. It should be used with the Caterpillar Fuel Usage Guide for the engine and rating to determine the rating for the fuelspecified. A Fuel Usage Guide for each rating is included on page 2 of its standard technical data sheet.

RPC always applies to naturally aspirated (NA) engines, and turbocharged (TA or LE) engines only when they are derated for altitude and ambient site conditions.

Project specific technical data sheets generated by the Caterpillar Data Maintenance Utility program take the Caterpillar Methane Number and RPC into account when generating a site rating.

Fuel properties for Btu/scf calculations are at 60F and 14.696 psia.

Caterpillar shall have no liability in law or equity, for damages, consequently or otherwise, arising from use of program and related material or any part thereof.

FUEL LIQUIDSFUEL LIQUIDSFUEL LIQUIDSFUEL LIQUIDSField gases, well head gases, and associated gases typically contain liquid water and heavy hydrocarbons entrained in the gas. To prevent detonation and severe damage to the engine, hydrocarbonliquids must not be allowed to enter the engine fuel system. To remove liquids, a liquid separator and coalescing filter are recommended, with an automatic drain and collection tank to preventcontamination of the ground in accordance with local codes and standards.

To avoid water condensation in the engine or fuel lines, limit the relative humidity of water in the fuel to 80% at the minimum fuel operating temperature.

WARNING(S)WARNING(S)WARNING(S)WARNING(S)1. The wobbe index of the fuel is higher than or equal to 1500 Btu/scf and is lower than 1900 Btu/scf. Requires two 219-4205 carburetor valve and jet kits plus two 7E-1569 washers. Will require on-siteadjustment or tuning of the fuel system to determine if washers are needed to maintain constant NOx emissions for 50 - 100% load.


Attachment 3 Engine Emission Calculations


Genset Emissions Summary - Each EngineEmission Factor Hourly Daily Annual

g/hp-hr lb/hour lb/day ton/yearCO 2.00 2.53 60.63 11.07NOx 1.00 1.26 30.32 5.53VOC 0.70 0.88 21.22 3.87Genset Emissions Summary - Total of Three Engines

Emission Factor Hourly Daily Annualg/hp-hr lb/hour lb/day ton/year

CO 2.00 7.58 181.90 33.20NOx 1.00 3.79 90.95 16.60VOC 0.70 2.65 63.67 11.62Note:1. To be conservative, emissions were calculated based on 100% load.2. Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst(Attachment 2)

Detailed Emission Calculations

Propane Genset CAT G3412C LEModel: G3412C LEPrime Power 376 kW per unitEngine Rating 573 bhp per unitNumber of Units 3 unitOperating hours 24 hours/day

365 days/yearDaily and Annual Emissions Calculation (100% Load)

VOC NOx COStandard for subpart JJJJ (ppm @ 15% O2) 60 82 270Standard for subpart JJJJ (g/hp-hr) 0.70 1.00 2.00Engine G3412C LE emission factor (ppm @15% O2) 60 82 270Engine G3412C emission factor (g/hp-hr) 0.70 1.00 2.00Emissions per unit (lb/day) 21.22 30.32 60.63Total emissions of all units (lb/day) 63.67 90.95 181.90Emissions per unit (ton/year) 3.87 5.53 11.07Total emissions of all units (ton/year) 11.62 16.60 33.20Note:

Hourly Emissions Calculation - at 50% and 100% Load

g/hp-hr lb/hr g/hp-hr lb/hrCO 2.00 1.26 2.00 2.53NOx 1.00 0.63 1.00 1.26VOC 0.70 0.44 0.70 0.88Sox NA NA NA NAPM10 NA NA NA NALead NA NA NA NANote: NOx emission factor @50% load used the data of 52% load from the specification data. Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst (Attachment 2).

1. Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst (Attachment 2).

50% load 100% load

SUPPLEMENTAL INFORMATION PROVIDED TO THE AIR DISTRICT

REGARDING THE PERMIT APPLICATIONS FOR THE GENERATORS –

FEBRUARY 2, 2016

CH2M Redding 2525 Airpark Drive Redding, CA 96001-2443 Tel 530.243.5831 Fax 530.243.1654 www.ch2m.com

Mr. James E. Smith County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097

February 2, 2016

Subject: Additional Information for the Permit Application for an Authority to Construct/Permit to Operate for Three Propane-powered Electricity Generators at Crystal Geyser Water Company, Mt. Shasta, California Facility – Submitted on December 17, 2015

Dear Mr. Smith,

This letter provides the additional information you requested in your letter dated January 20, 2016, for the permit application for an Authority to Construct/Permit to Operate for three new electricity generators at the Crystal Geyser Water Company facility at 210 Ski Village Drive, near Mt. Shasta, Siskiyou County, California.

1. Clarifications regarding engine horsepower rating and catalyst model number are summarized below, and the detailed clarifications are included in the letter prepared by Peterson Power Systems dated January 27, 2016 (see Attachment 1).

• The correct engine horsepower rating is 532 brake horsepower (bhp) for each engine. The 576 bhp rating used in the original application was not correct.

• The 637 bhp listed in the Caterpillar Gas Engine Site Specific Technical Data remains in the data sheet. The 637 bhp @ 1800 rpm is the Standard Rated Power for the engine when it is powered by natural gas at altitudes below 500 feet. The site-specific power rating of the engine for project site conditions and fueled by propane is 532 bhp. The Standard Rated Power is always included on Caterpillar data sheets, but it will not be used for the permit application.

• The catalyst model is 2-DC63F-8 CC. Clarifications were added to table headings in Attachment 1.

The original permit application dated December 17, 2015, was based on an incorrect engine power rating of 576 bhp. Therefore, the application’s supplemental forms for power generators and the emission calculations were updated using the 532 bhp rating and are included in Attachment 2 and Attachment 3, respectively.

2. Clarifications regarding NOx emission controls and the details of the oxidation catalysts are included in the letter prepared by Peterson Power Systems (see Attachment 1).

3. Clarifications regarding detail emission control systems and monitoring devices for the generator sets are included in the letter prepared by Peterson Power Systems (see Attachment 1).

February 2, 2016 Mr. James E. Smith

If you have questions or need additional information, please contact Peter Rude at (530) 229-3396 or Hong Zhuang at (714) 435-6349.

Regards,

CH2M HILL, Inc.

Hong Zhuang Peter H. Rude, P.E Project Engineer Project Manager

Attachment 1 Clarifications and Updated Engine Data

Provided by Peterson Power System

Since 1936

2828 Teagarden Street, San Leandro, CA 94577 Telephone (510) 895-8400 petersonpower.com

January 27, 2016

Peter H. Rude, P.E. Civil Engineer CH2M HILL 2525 Airpark Drive Redding, CA 96001 Via email to: [email protected] Reference:

Crystal Geyser Water Company Air Permit – responses to APCD letter of 20 January 2016

Conflicting information regarding engine rating:

The Caterpillar data sheet (SRR G15-3400-197) showed the correct electrical output but the maximum available engine power with an engine driven fan. This installation will use electric motor driven fans and, as such, Caterpillar has replaced this with a revised data sheet (SRR G16-3400-008) showing 532 bhp at 1800 rpm.

There were slight differences in the engine data so we have, in conjunction with the catalyst manufacturer DCL, revised the emission guarantee data sheet to reflect those changes.

The 530 bhp shown on the Peterson Power Systems Emissions Data has been corrected to 532 bhp. The reason for this adjustment is the generator efficiency we originally used was 95.1%; the revised data sheet shows generator efficiency of 94.7%. Math as follows:

• Original: 376 kWe ÷ .951 generator efficiency = 395 kWb; 395 kWb ÷ 0.7457 bhp/kW = 530 bhp

• Revised: 376 kWe ÷ .947 generator efficiency = 397 kWb; 395 kWb ÷ 0.7457 bhp/kW = 532 bhp

NOx controls:

Caterpillar factory testing is done with natural gas; propane is not available in the production test facility. The engine is shipped with natural gas specific carburetor cones, springs and seats. Propane specific carburetor cones, springs and seats are shipped with the engine and installed by Peterson Power Systems.

Since 1936

2828 Teagarden Street, San Leandro, CA 94577 Telephone (510) 895-8400 petersonpower.com

When the engine is fitted with Caterpillar supplied propane specified carburetor cones, springs and seats to maintain the NOx level of 1 gram/bhp-hr from 100% rated load (376 kWe) to 60% rated load (225 kWe). This will be demonstrated during the source testing.

Peterson will provide a bypass Air/Fuel Ratio Control (Gill A/F 120) as part of the standard package. This will provide a small display that shows:

• lambda (mA) – this allows tracking of A/F ratio • lambda heater resistance (ohms) – this monitors the health of the lambda sensor • bypass valve position – this shows the amount of trim required to maintain the required

lambda and is a diagnostic tool.

The A/F 120 allows for the alarm settings for out of tolerance operation. We can provide a pyrometers and a display for engine out and catalyst out temperature monitoring with alarms for out of tolerance.

Dynamic backpressure is difficult to measure; it can be measured and recorded it a prescribed interval. Peterson will work with the catalyst supplier to determine a condemning limit for the elements based on pressure drop across the catalyst.

Attachments:

• Caterpillar Site Data Sheet SRR G16-3400-008 • DCL Oxidizing Catalyst Data Sheet & Emissions Guarantee • Revised Peterson Emissions Data Sheet • Gill A/F 120 Bulletin

Please contact Peterson if require further information.

Best regards,

Martin Hopkins Sales Representative Biogas, Natural Gas & Cogeneration Peterson Power Systems Gas Energy Division 541.736.2867

G3412C GAS ENGINE SITE SPECIFIC TECHNICAL DATAGENSET APPLICATION Crystal GeyserENGINE SPEED (rpm): 1800 RATING STRATEGY: STANDARDCOMPRESSION RATIO: 8.5 RATING LEVEL: CONTINUOUSAFTERCOOLER TYPE: SCAC FUEL SYSTEM: LPG IMPCOAFTERCOOLER WATER INLET (°F): 130 WITH CUSTOMER SUPPLIED AIR FUEL RATIO CONTROLJACKET WATER OUTLET (°F): 210 SITE CONDITIONS:ASPIRATION: TA FUEL: G16-3400-008 (00)COOLING SYSTEM: JW+OC, AC FUEL PRESSURE RANGE(psig): 1.5-5.0CONTROL SYSTEM: EIS FUEL METHANE NUMBER: 32.9EXHAUST MANIFOLD: WC FUEL LHV (Btu/scf): 2299COMBUSTION: LOW EMISSION ALTITUDE(ft): 3100NOx EMISSION LEVEL (g/bhp-hr NOx): 1.0 MAXIMUM INLET AIR TEMPERATURE(°F): 90SET POINT TIMING: 21 STANDARD RATED POWER: 637 bhp@1800rpm

POWER FACTOR: 1.0VOLTAGE(V): 480-480

MAXIMUMRATING


RATING NOTES LOAD 100% 100% 75% 60% GENSET POWER (WITHOUT FAN) (1)(2) ekW 376 282 225

GENSET POWER (WITHOUT FAN) (1)(2) kVA 376 282 225

ENGINE POWER (WITHOUT FAN) (2) bhp 532 399 319

INLET AIR TEMPERATURE °F 90 90 90

GENERATOR EFFICIENCY (1) % 94.7 94.7 94.7

GENSET EFFICIENCY (ISO 3046/1) (3) % 27.8 26.8 25.9

THERMAL EFFICIENCY (4) % 55.0 57.2 59.3

TOTAL EFFICIENCY (5) % 82.8 84.0 85.2

ENGINE DATA GENSET FUEL CONSUMPTION (ISO 3046/1) (6) Btu/ekW-hr 12292 12720 13155 GENSET FUEL CONSUMPTION (NOMINAL) (6) Btu/ekW-hr 12531 12967 13410 ENGINE FUEL CONSUMPTION (NOMINAL) (6) Btu/bhp-hr 8849 9157 9470 AIR FLOW (@inlet air temp, 14.7 psia) (WET) (7)(8) ft3/min 1172 893 721

AIR FLOW (WET) (7)(8) lb/hr 5078 3870 3125

FUEL FLOW (60ºF, 14.7 psia) scfm 34 26 22

INLET MANIFOLD PRESSURE (9) in Hg(abs) 54.9 42.2 35.2

EXHAUST TEMPERATURE - ENGINE OUTLET (10) °F 900 874 865


(WET) (11)(8) ft3/min 3119 2334 1875

EXHAUST GAS MASS FLOW (WET) (11)(8) lb/hr 5314 4053 3276

EMISSIONS DATA - ENGINE OUT NOx (as NO2) (12)(13) g/bhp-hr 1.00 1.00 1.00

CO (12)(13) g/bhp-hr 2.95 3.09 3.17

THC (mol. wt. of 15.84) (12)(13) g/bhp-hr 2.18 2.60 2.86

NMHC (mol. wt. of 15.84) (12)(13) g/bhp-hr 2.18 2.60 2.86

NMNEHC (VOCs) (mol. wt. of 15.84) (12)(13)(14) g/bhp-hr 2.18 2.60 2.86

HCHO (Formaldehyde) (12)(13) g/bhp-hr 0.30 0.32 0.34

CO2 (12)(13) g/bhp-hr 597 601 611

EXHAUST OXYGEN (12)(15) % DRY 7.1 7.0 7.0

HEAT REJECTION LHV INPUT (16) Btu/min 78459 60893 50271 HEAT REJ. TO JACKET WATER (JW) (17) Btu/min 25600 21508 18864 HEAT REJ. TO ATMOSPHERE (17) Btu/min 3138 2436 2011 HEAT REJ. TO LUBE OIL (OC) (17) Btu/min 4048 3401 2983 HEAT REJECTION TO EXHAUST (LHV TO 350°F) (17) Btu/min 13243 9625 7656 HEAT REJ. TO AFTERCOOLER (AC) (17)(18) Btu/min 2863 1563 804

COOLING SYSTEM SIZING CRITERIA TOTAL JACKET WATER CIRCUIT (JW+OC) (19) Btu/min 33018 TOTAL AFTERCOOLER CIRCUIT (AC) (19) Btu/min 4607 HEAT REJECTION TO EXHAUST (LHV TO 350°F) (19) Btu/min 14567 A cooling system safety factor of 0% has been added to the cooling system sizing criteria.

MINIMUM HEAT RECOVERY TOTAL JACKET WATER CIRCUIT (JW+OC) (20) Btu/min 26278 TOTAL AFTERCOOLER CIRCUIT (AC) (20) Btu/min 2720 HEAT REJECTION TO EXHAUST(LHV TO 350°F) (20) Btu/min 11036



PREPARED BY:Data generated by Data Maintenance Utility Version 6.00.00Special Rating Request G16-3400-008 (00), Printed 26Jan2016 Page 1 of 4

376

376

532

90

94.7

27.8

55.0

82.8

12292

12531

8849

1172

5078

34

54.9

900

3119

5314

1.00

2.95

2.18

2.18

2.18

0.30

597

7.1

78459

25600

3138

4048

13243

2863

33018

4607

14567

26278

2720

11036

G3412C GAS ENGINE SITE SPECIFIC TECHNICAL DATAGENSET APPLICATION Crystal Geyser

Engine Power vs. Inlet Air TemperatureData represents temperature sweep at 3100 ft and 1800 rpm

No Rating AvailableRange for Site Conditions

Continuous OperatingRange for Site Conditions

Low Load IntermittentOperating Range

Air Temperature, °FAir Temperature, °FAir Temperature, °FAir Temperature, °F

30303030 40404040 50505050 60606060 70707070 80808080 90909090 100100100100 110110110110 120120120120 130130130130

EE EEnn nn

gg ggii iinn nn

ee eePP PP

oo ooww ww

ee eerr rr,, ,,

bb bbhh hh

pp pp

0000

100100100100

200200200200

300300300300

400400400400

500500500500

600600600600

700700700700EEEEnnnn

ggggiiii nnnn

eeeePPPP

oooowwww

eeeerrrr ,,,,

bbbbhhhh

pppp

0000

100100100100

200200200200

300300300300

400400400400

500500500500

600600600600

700700700700



NOTES1. Generator efficiencies, power factor, and voltage are based on specified generator. [Genset Power (ekW) is calculated as: Engine Power (bkW) x GeneratorEfficiency], [Genset Power (kVA) is calculated as: Engine Power (bkW) x Generator Efficiency / Power Factor]


3. Genset Effieciency published in accordance with ISO 3046/1.


5. Total efficiency is calculated as: Genset Efficiency + Thermal Efficiency. Tolerance is ±10% of full load data.

6. ISO 3046/1 Genset fuel consumption tolerance is (+)5, (-)0% at the specified power factor. Nominal genset and engine fuel consumption tolerance is ± 3.0% of fullload data at the specified power factor.

























Fuel Makeup: G16-3400-008 (00)
























GLOBAL LEADER IN EMISSIONS CONTROL SOLUTIONS

EMISSION GUARANTEE

Provided by: William Casolara

January 27, 2016

Confidential


EMISSION GUARANTEE


January 27, 2016

Confidential


EMISSION GUARANTEE


January 27, 2016

Confidential

DCL America Inc. 27603 Commerce Oaks Drive, Oak Ridge North, TX 77385Toll free: 1-877-965-8989 Fax: 281-605-5858 Email: [email protected] www.dcl-inc.com

January 27, 2016

Mike ShortPeterson Power

RE: G3412 propane rating

Mr. Short,

I am pleased to provide this emission guarantee based on the following information. If you have any questions orconcerns please feel free to contact myself or any of my associates at DCL America.

Also, this guarantee is subject to DCL’s standard terms and conditions of sale attached. Copies of the limitedwarranty statement are available from DCL upon request (DCL doc. No. X0010-0000-68).

Best Regards,

Will CasolaraSenior Sales EngineerDCL America Inc.

Cell: [email protected]


EMISSION GUARANTEE

ENGINE DATA

Engine Model CAT G3412C

Power 532 bhp

Fuel PQNG or Propane

Exhaust Flow Rate 3119 acfm

Exhaust Temperature 900° F

The catalyst model selection is based upon the reduction requirements above. Any variance in theserequirements may affect the price and model required.

CATALYST DATA

Catalyst Model 2-DC63F-8 CC

Type Oxidation

# of Elements 2

Cell Density 300 cpsi

Element Dimensions 20.4” Ø x 3.75”

Approx. Backpressure 5.7” w.c.

EMISSION REQUIREMENTS

Exhaust Component Engine Output(g/bhp-hr)

Converter Output(ppmvd @ 15% O2)

CO 2.95 <270

VOC 2.18 <60


EMISSION GUARANTEE

ENGINE DATA


Power 532 bhp





CATALYST DATA


Type Oxidation

# of Elements 2







CO 2.95 <270

VOC 2.18 <60


EMISSION GUARANTEE

ENGINE DATA


Power 532 bhp





CATALYST DATA


Type Oxidation

# of Elements 2







CO 2.95 <270

VOC 2.18 <60

Crystal Geyser

G3412C LE

Propane Fueled

5078

532

376

7.10

OUTPUT







27‐Jan‐16

Load Btu/hour

100% 4,707,540

75% 3,653,580

60% 3,016,260

50% 2,603,281


Fuel gas: Propane (HD‐5)

Caterpillar Data Site Data Sheet: G16‐3400‐008

DCL Oxidizing Catalyst Model: 2‐DC63F‐8 CC

kWe

376

282

225

188


Fuel gas: Propane (HD‐5) Caterpillar Data Site Data Sheet: G16‐3400‐008


INPUT

EPA 40 CFR Part

60 Subpart jjjj

requirements








Crystal Geyser

G3412C LE


IDU-10

1609-00-010

Gill Instruments Ltd

072805

OkEsc

Digital Display (Optional)

Shielded Enclosure(Optional)

Air/Fuel Controller

Fuel Bypass Valve

Oxygen Sensor

AIR/FUEL MODULEZeroDriftZeroDrift

1495-00-026C123AF120

The Gill ZeroDrift Air/Fuel Ratio Control System provides

cost-effective emissions control for stationary and

portable industrial gas engines. The system automatically

controls the optimum air/fuel ratio throughout the

engine’s use, ensuring the engine remains continuously in

compliance with emission standards.

System Overview

Featured Products

ZeroDrift Package

The ZeroDrift air/fuel controller has been designed to control air/fuel ratio of both rich (stoichiometric) or lean burn

industrial gas engines. The system improves engine efficiency and eliminates the requirement for constant manual

engine adjustment often associated with other air/fuel ratio control technologies.

EH12 Shielded Enclosure

AF120Air/Fuel Control Module

Fuel Bypass Valve

IDU10 Digital Display

ZeroDriftAir/Fuel Control

9

Attachment 2 Updated Power Generators

Supplemental Forms





B. This application must accompany a Permit Application form. C. Each application must be filled out completely and accompanied by adequate plans and operating


application.

LEGAL OWNER

Name:

Address:

City/Zip:

Phone/Fax:

e-mail:

OPERATOR



City/Zip:

Phone/Fax:

e-mail:






707-972-0500

[email protected]




707-972-0500

[email protected]

210 Ski Village Drive Mt. Shasta California, CA 96067



Manufacture:

Model #:

Serial #:

Horsepower (hp):

Btu/hour:



Fuel Type:















Propane


Caterpillar

To be determined


2015

532

3,293,760 (annual)

3,293,760 (annual)

24

365

NA

1.17 lb/hr @50%, 2.35 lb/hr @100% power

0.59 lb/hr @ 50%, 1.17 lb/hr @ 100% power

Negligible

Negligible

Negligible





School ft. :

Hospital ft.:

Daycare ft.:

Resident ft. :


700

2,700

3,200

3,500







application.

LEGAL OWNER

Name:

Address:

City/Zip:

Phone/Fax:

e-mail:

OPERATOR



City/Zip:

Phone/Fax:

e-mail:






707-972-0500

[email protected]




707-972-0500

[email protected]




Manufacture:

Model #:

Serial #:

Horsepower (hp):

Btu/hour:



Fuel Type:















Propane


Caterpillar

To be determined


2015

532

3,293,760 (annual)

3,293,760 (annual)

24

365

NA

1.17 lb/hr @50%, 2.35 lb/hr @100% power

0.59 lb/hr @ 50%, 1.17 lb/hr @ 100% power

Negligible

Negligible

Negligible





School ft. :

Hospital ft.:

Daycare ft.:

Resident ft. :


700

2,700

3,200

3,500







application.

LEGAL OWNER

Name:

Address:

City/Zip:

Phone/Fax:

e-mail:

OPERATOR



City/Zip:

Phone/Fax:

e-mail:






707-972-0500

[email protected]




707-972-0500

[email protected]




Manufacture:

Model #:

Serial #:

Horsepower (hp):

Btu/hour:



Fuel Type:















Propane


Caterpillar

To be determined


2015

532

3,293,760 (annual)

3,293,760 (annual)

24

365

NA

1.17 lb/hr @50%, 2.35 lb/hr @100% power

0.59 lb/hr @ 50%, 1.17 lb/hr @ 100% power

Negligible

Negligible

Negligible





School ft. :

Hospital ft.:

Daycare ft.:

Resident ft. :


700

2,700

3,200

3,500

Aerial photo source: Google ©2014, modified by CH2M HILL.

Legend

CGWC Property Line

WBG031814043631RDD CG_LocationData_Figure1_V2.ai cmont 12/15/15

Figure 1: Location DataPower Generators SupplementalApplication Form for County of SiskiyouAir Pollution Control DistrictCrystal Geyser Water Company

North

0 300

Approximate scale in feet

100 200 400 500

FIRESUPPRESSION

TANK

DOMESTICWELL AND

PUMP HOUSE

SKI VILLAGE DR.

CGWCBOTTLING PLANT

BUTTE AVE.

SHASTA AVE.

N. M

T. SH

AS

TA B

LVD

.

MCCLOUD RAILROAD

3 PROPANEPOWER GENERATORS

PROPANETANK

Attachment 3 Updated Engine Emission Calculations


Genset Emissions Summary - Each EngineEmission Factor Hourly Daily Annual

g/hp-hr lb/hour lb/day ton/yearCO 2.00 2.35 56.30 10.27NOx 1.00 1.17 28.15 5.14VOC 0.70 0.82 19.70 3.60Genset Emissions Summary - Total of Three Engines

Emission Factor Hourly Daily Annualg/hp-hr lb/hour lb/day ton/year

CO 2.00 7.04 168.89 30.82NOx 1.00 3.52 84.44 15.41VOC 0.70 2.46 59.11 10.79Note:1. To be conservative, emissions were calculated based on 100% load.2. Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst (Attachment 1)

Detailed Emission Calculations

Propane Genset CAT G3412C LEModel: G3412C LEPrime Power 376 kW per unitEngine Rating 532 bhp per unitNumber of Units 3 unitOperating hours 24 hours/day

365 days/yearDaily and Annual Emissions Calculation (100% Load)

VOC NOx COStandard for subpart JJJJ (ppm @ 15% O2) 60 82 270Standard for subpart JJJJ (g/hp-hr) 0.70 1.00 2.00Engine G3412C LE emission factor (ppm @15% O2) 60 82 270Engine G3412C emission factor (g/hp-hr) 0.70 1.00 2.00Emissions per unit (lb/day) 19.70 28.15 56.30Total emissions of all units (lb/day) 59.11 84.44 168.89Emissions per unit (ton/year) 3.60 5.14 10.27Total emissions of all units (ton/year) 10.79 15.41 30.82Note:

(Attachment 1).

Hourly Emissions Calculation - at 50% and 100% Load

g/hp-hr lb/hr g/hp-hr lb/hrCO 2.00 1.17 2.00 2.35NOx 1.00 0.59 1.00 1.17VOC 0.70 0.41 0.70 0.82SOx NA NA NA NAPM10 NA NA NA NALead NA NA NA NANote: NOx emission factor @50% load used the data of 60% load from the specification data. Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst (Attachment 1).

1. Engine emission factors for VOC and CO used the guaranteed emission rates with the oxidation catalyst

50% load 100% load

SUPPLEMENTAL INFORMATION PROVIDED TO THE AIR DISTRICT

REGARDING THE PERMIT APPLICATIONS FOR THE GENERATORS –

FEBRUARY 5, 2016

CH2M Redding 2525 Airpark Drive Redding, CA 96001-2443 Tel 530.243.5831 Fax 530.243.1654 www.ch2m.com

Mr. James E. Smith County of Siskiyou Air Pollution Control District 525 South Foothill Drive Yreka, California 96097

February 5, 2016

Subject: Additional Clarification for the Permit Application for an Authority to Construct/Permit to Operate for Three Propane-powered Electricity Generators at Crystal Geyser Water Company, Mt. Shasta, California Facility – Submitted on December 17, 2015

Dear Mr. Smith,

This letter provides additional clarification your staff requested on February 4, 2016 concerning information presented in our February 2, 2016 submittal which included Attachment 1 “Clarifications and Updated Engine Data Provided by Peterson Power System.”

The letter from Peterson Power has been revised to provide the clarifications desired, the attachments from Peterson Power Systems are unchanged from February 2 but are provided here for consistency. Please replace the entire Attachment 1 from the February 2, 2016 submittal with the Attachment 1 that is provided with this letter.

If you have questions or need additional information, please contact Peter Rude at (530) 229-3396 or Hong Zhuang at (714) 435-6349.

Regards,

CH2M HILL, Inc.

Hong Zhuang Peter H. Rude, P.E Project Engineer Project Manager

Attachment 1 Clarifications and Updated Engine Data

Provided by Peterson Power System (February 5, 2017)

Peter H. Rude, P.E. Civil Engineer CH2M HILL 2525 Airpark Drive Redding, CA 96001

Via email to: [email protected]

Reference:


Air Permit- responses to APCD letter of 20 January 2016

Conflicting information regarding engine rating:

February 5, 2016

The Caterpillar data sheet (SRR G15-3400-197) showed the correct electrical output but the

maximum available engine power with an engine driven fan. This installation will use electric

motor driven fans and, as such, Caterpillar has replaced this with a revised data sheet (SRR G16-

3400-008) showing 532 bhp at 1800 rpm.

There were slight differences in the engine data so we have, in conjunction with the catalyst

manufacturer DCL, revised the emission guarantee data sheet to reflect those changes.

The 530 bhp shown on the Peterson Power Systems Emissions Data has been corrected to 532

bhp. The reason for this adjustment is the generator efficiency we originally used was 95.1%;

the revised data sheet shows generator efficiency of 94. 7%. Math as follows:

• Original: 376 kWe + .951 generator efficiency= 395 kWb; 395 kWb + 0.7457 bhp/kW =

530 bhp

• Revised: 376 kWe + .947 generator efficiency= 397 kWb; 395 kWb + 0.7457 bhp/kW =

532 bhp

NOx controls:

Caterpillar factory testing is done with natural gas; propane is not available in the production

test facility. The engine is shipped with natural gas specific carburetor cones, springs and seats.

Propane specific carburetor cones, springs and seats are shipped with the engine and installed

by Peterson Power Systems.

The engine will be fitted onsite by Peterson Power Systems with Caterpillar supplied propane

specified carburetor cones, springs and seats to maintain the NOx level of 1 gram/bhp-hr from

Since 1936

2828 Teagarden Street, San Leandro, CA 94577 ~ Telephone (510) 895-8400 ~ petersonpower.com

100% rated load (376 kWe) to 60% rated load (225 kWe). This will be demonstrated during the

source testing.

Third Party source testing will occur within 30 days of submittal of the Start-up Notification to

the Siskiyou County APCD.

Peterson will provide a bypass Air/Fuel Ratio Control (Gill Zero Drift A/F 120) as part ofthe

standard package. This will provide a small display that shows:

• lambda (mA)- this allows tracking of A/F ratio

• lambda heater resistance (ohms)- this monitors the health of the lambda sensor

• bypass valve position- this shows the amount of trim required to maintain the required

lambda and is a diagnostic tool.

The Gill Zero Drift A/F 120 allows for the alarm settings for out of tolerance operation. We will

provide pre- and post-catalyst pyrometers and a display for engine out and catalyst out

temperature monitoring with alarms for out of tolerance.

Peterson will work with the catalyst supplier to determine a condemning limit (defined as a

percentage increase in pressure drop across the catalyst) from baseline measurements taken

and recorded during source testing.

The operator will take and record pressure backpressure at 90 day intervals. This will allow the

operator to determine the health of the catalyst and make arrangements for its cleaning and/or

replacement before the condemning limit is reached.

Attachments:

• Caterpillar Site Data Sheet SRR G16-3400-008

• DCL Oxidizing Catalyst Data Sheet & Emissions Guarantee

• Revised Peterson Emissions Data Sheet

• Gill Zero Drift A/F 120 Bulletin

;!;!;gar , , · Martm Hopkms

Sales Representative Biogas, Natural Gas & Cogeneration Peterson Power Systems Gas Energy Division 541.736.2867

Since 1936

2828 Teagarden Street, San Leandro, CA 94577 ~ Telephone (510) 895-8400 ~ petersonpower.com

G3412C GAS ENGINE SITE SPECIFIC TECHNICAL DATAGENSET APPLICATION Crystal GeyserENGINE SPEED (rpm): 1800 RATING STRATEGY: STANDARDCOMPRESSION RATIO: 8.5 RATING LEVEL: CONTINUOUSAFTERCOOLER TYPE: SCAC FUEL SYSTEM: LPG IMPCOAFTERCOOLER WATER INLET (°F): 130 WITH CUSTOMER SUPPLIED AIR FUEL RATIO CONTROLJACKET WATER OUTLET (°F): 210 SITE CONDITIONS:ASPIRATION: TA FUEL: G16-3400-008 (00)COOLING SYSTEM: JW+OC, AC FUEL PRESSURE RANGE(psig): 1.5-5.0CONTROL SYSTEM: EIS FUEL METHANE NUMBER: 32.9EXHAUST MANIFOLD: WC FUEL LHV (Btu/scf): 2299COMBUSTION: LOW EMISSION ALTITUDE(ft): 3100NOx EMISSION LEVEL (g/bhp-hr NOx): 1.0 MAXIMUM INLET AIR TEMPERATURE(°F): 90SET POINT TIMING: 21 STANDARD RATED POWER: 637 bhp@1800rpm

POWER FACTOR: 1.0VOLTAGE(V): 480-480

MAXIMUMRATING


RATING NOTES LOAD 100% 100% 75% 60% GENSET POWER (WITHOUT FAN) (1)(2) ekW 376 282 225

GENSET POWER (WITHOUT FAN) (1)(2) kVA 376 282 225

ENGINE POWER (WITHOUT FAN) (2) bhp 532 399 319

INLET AIR TEMPERATURE °F 90 90 90

GENERATOR EFFICIENCY (1) % 94.7 94.7 94.7

GENSET EFFICIENCY (ISO 3046/1) (3) % 27.8 26.8 25.9

THERMAL EFFICIENCY (4) % 55.0 57.2 59.3

TOTAL EFFICIENCY (5) % 82.8 84.0 85.2

ENGINE DATA GENSET FUEL CONSUMPTION (ISO 3046/1) (6) Btu/ekW-hr 12292 12720 13155 GENSET FUEL CONSUMPTION (NOMINAL) (6) Btu/ekW-hr 12531 12967 13410 ENGINE FUEL CONSUMPTION (NOMINAL) (6) Btu/bhp-hr 8849 9157 9470 AIR FLOW (@inlet air temp, 14.7 psia) (WET) (7)(8) ft3/min 1172 893 721

AIR FLOW (WET) (7)(8) lb/hr 5078 3870 3125

FUEL FLOW (60ºF, 14.7 psia) scfm 34 26 22

INLET MANIFOLD PRESSURE (9) in Hg(abs) 54.9 42.2 35.2

EXHAUST TEMPERATURE - ENGINE OUTLET (10) °F 900 874 865


(WET) (11)(8) ft3/min 3119 2334 1875

EXHAUST GAS MASS FLOW (WET) (11)(8) lb/hr 5314 4053 3276

EMISSIONS DATA - ENGINE OUT NOx (as NO2) (12)(13) g/bhp-hr 1.00 1.00 1.00

CO (12)(13) g/bhp-hr 2.95 3.09 3.17

THC (mol. wt. of 15.84) (12)(13) g/bhp-hr 2.18 2.60 2.86

NMHC (mol. wt. of 15.84) (12)(13) g/bhp-hr 2.18 2.60 2.86

NMNEHC (VOCs) (mol. wt. of 15.84) (12)(13)(14) g/bhp-hr 2.18 2.60 2.86

HCHO (Formaldehyde) (12)(13) g/bhp-hr 0.30 0.32 0.34

CO2 (12)(13) g/bhp-hr 597 601 611

EXHAUST OXYGEN (12)(15) % DRY 7.1 7.0 7.0

HEAT REJECTION LHV INPUT (16) Btu/min 78459 60893 50271 HEAT REJ. TO JACKET WATER (JW) (17) Btu/min 25600 21508 18864 HEAT REJ. TO ATMOSPHERE (17) Btu/min 3138 2436 2011 HEAT REJ. TO LUBE OIL (OC) (17) Btu/min 4048 3401 2983 HEAT REJECTION TO EXHAUST (LHV TO 350°F) (17) Btu/min 13243 9625 7656 HEAT REJ. TO AFTERCOOLER (AC) (17)(18) Btu/min 2863 1563 804

COOLING SYSTEM SIZING CRITERIA TOTAL JACKET WATER CIRCUIT (JW+OC) (19) Btu/min 33018 TOTAL AFTERCOOLER CIRCUIT (AC) (19) Btu/min 4607 HEAT REJECTION TO EXHAUST (LHV TO 350°F) (19) Btu/min 14567 A cooling system safety factor of 0% has been added to the cooling system sizing criteria.

MINIMUM HEAT RECOVERY TOTAL JACKET WATER CIRCUIT (JW+OC) (20) Btu/min 26278 TOTAL AFTERCOOLER CIRCUIT (AC) (20) Btu/min 2720 HEAT REJECTION TO EXHAUST(LHV TO 350°F) (20) Btu/min 11036




376

376

532

90

94.7

27.8

55.0

82.8

12292

12531

8849

1172

5078

34

54.9

900

3119

5314

1.00

2.95

2.18

2.18

2.18

0.30

597

7.1

78459

25600

3138

4048

13243

2863

33018

4607

14567

26278

2720

11036


Engine Power vs. Inlet Air TemperatureData represents temperature sweep at 3100 ft and 1800 rpm

No Rating AvailableRange for Site Conditions

Continuous OperatingRange for Site Conditions

Low Load IntermittentOperating Range

Air Temperature, °FAir Temperature, °FAir Temperature, °FAir Temperature, °F

30303030 40404040 50505050 60606060 70707070 80808080 90909090 100100100100 110110110110 120120120120 130130130130

EE EEnn nn

gg ggii iinn nn

ee eePP PP

oo ooww ww

ee eerr rr,, ,,

bb bbhh hh

pp pp

0000

100100100100

200200200200

300300300300

400400400400

500500500500

600600600600

700700700700EEEEnnnn

ggggiiii nnnn

eeeePPPP

oooowwww

eeeerrrr ,,,,

bbbbhhhh

pppp

0000

100100100100

200200200200

300300300300

400400400400

500500500500

600600600600

700700700700



NOTES1. Generator efficiencies, power factor, and voltage are based on specified generator. [Genset Power (ekW) is calculated as: Engine Power (bkW) x GeneratorEfficiency], [Genset Power (kVA) is calculated as: Engine Power (bkW) x Generator Efficiency / Power Factor]


3. Genset Effieciency published in accordance with ISO 3046/1.


5. Total efficiency is calculated as: Genset Efficiency + Thermal Efficiency. Tolerance is ±10% of full load data.

6. ISO 3046/1 Genset fuel consumption tolerance is (+)5, (-)0% at the specified power factor. Nominal genset and engine fuel consumption tolerance is ± 3.0% of fullload data at the specified power factor.

























Fuel Makeup: G16-3400-008 (00)

























EMISSION GUARANTEE


January 27, 2016

Confidential


EMISSION GUARANTEE


January 27, 2016

Confidential


EMISSION GUARANTEE


January 27, 2016

Confidential


January 27, 2016

Mike ShortPeterson Power

RE: G3412 propane rating

Mr. Short,

I am pleased to provide this emission guarantee based on the following information. If you have any questions orconcerns please feel free to contact myself or any of my associates at DCL America.

Also, this guarantee is subject to DCL’s standard terms and conditions of sale attached. Copies of the limitedwarranty statement are available from DCL upon request (DCL doc. No. X0010-0000-68).

Best Regards,

Will CasolaraSenior Sales EngineerDCL America Inc.

Cell: [email protected]


EMISSION GUARANTEE

ENGINE DATA


Power 532 bhp





CATALYST DATA


Type Oxidation

# of Elements 2







CO 2.95 <270

VOC 2.18 <60


EMISSION GUARANTEE

ENGINE DATA


Power 532 bhp





CATALYST DATA


Type Oxidation

# of Elements 2







CO 2.95 <270

VOC 2.18 <60


EMISSION GUARANTEE

ENGINE DATA


Power 532 bhp





CATALYST DATA


Type Oxidation

# of Elements 2







CO 2.95 <270

VOC 2.18 <60

Crystal Geyser

G3412C LE

Propane Fueled

5078

532

376

7.10

OUTPUT







27‐Jan‐16

Load Btu/hour

100% 4,707,540

75% 3,653,580

60% 3,016,260

50% 2,603,281


Fuel gas: Propane (HD‐5)

Caterpillar Data Site Data Sheet: G16‐3400‐008


kWe

376

282

225

188


Fuel gas: Propane (HD‐5) Caterpillar Data Site Data Sheet: G16‐3400‐008


INPUT

EPA 40 CFR Part

60 Subpart jjjj

requirements








Crystal Geyser

G3412C LE


IDU-10

1609-00-010

Gill Instruments Ltd

072805

OkEsc

Digital Display (Optional)

Shielded Enclosure(Optional)

Air/Fuel Controller

Fuel Bypass Valve

Oxygen Sensor

AIR/FUEL MODULEZeroDriftZeroDrift

1495-00-026C123AF120

The Gill ZeroDrift Air/Fuel Ratio Control System provides

cost-effective emissions control for stationary and

portable industrial gas engines. The system automatically

controls the optimum air/fuel ratio throughout the

engine’s use, ensuring the engine remains continuously in

compliance with emission standards.

System Overview

Featured Products

ZeroDrift Package

The ZeroDrift air/fuel controller has been designed to control air/fuel ratio of both rich (stoichiometric) or lean burn

industrial gas engines. The system improves engine efficiency and eliminates the requirement for constant manual

engine adjustment often associated with other air/fuel ratio control technologies.

EH12 Shielded Enclosure

AF120Air/Fuel Control Module

Fuel Bypass Valve

IDU10 Digital Display

ZeroDriftAir/Fuel Control

9

AUTHORITY TO CONSTRUCT/ PERMIT TO OPERATE PERMIT FOR

BACKUP GENERATOR

I .

COUNTY OF SISKIYOD AIR POLLUTION CONTROL DISTRICT

525 SOUTH FOOT!ITLL DRIVE YREKA, CALIFORNIA 96097-3090 PHONE: (530) 841-4029 FAX: (530) 842-6690

Authority to Construct

IS HEREBY GRANTED TO

CRYSTAL GEYSER WATER

ATC/PTO 141203-BUG

Owner Crystal Geyser Water Company

Richard Weklynch POBox 304

Calistoga, CA 94515-0304 (707) 942-0500

[email protected]

Operator Crystal Geyser Water Company

Zach Sm1re, MM 210 Ski Village Dr

Mt. Shasta, CA 96067 . (530) 918-9367 1)\sto.,nwl--.fty..,,c

[email protected]

EQUIPMENT LOCATION: 210 Ski Village Drive Mt. Shasta, CA

EQUIPMENT DESCRIPTION: Emergency Standby Diesel Generator

PATRICKJ. GRIFFIN Air Pollution Control Officer

POWER SOURCE: Kohler, ModellOOREOZJF, 158hp, 2014, Interim-Tier 4 Serial# PE4045L269881 Engine Family FJDXL04.5119

ATCIPTO 141203-BUG Crystal Geyser Water Amended April!, 2015 Pagel of5

This Authority to Construct/Permit to Operate {ATC/PTO) allows the legal owner/operator to construct and operate an Emergency Standby Diesel Generator according to the following conditions.

GENERAL CONDITIONS:

1. Conditions contained in this ATC/PTO are intended to assure that components of this facility are designed and operated in compliance with all Siskiyou County Air Pollution Control District (District) Rules and Regulations. The District reserves the right to amend this permit, if the need arises, to insure compliance of this facility or to abate any public nuisance. The legal owner/operator is also responsible for compliance with all other District, state and federal regulations not noted in this permit. [District Rule 2. 7, 4.2, 2.1 0]

2. This ATC shall not be transferable, whether by operation of law or otherwise from one location to another, from one person to another, or from one piece of equipment to another, except on written approval of the Control Officer. [District Rule 2.3]

3. Initial permit fees based upon the current fee schedules shall become due when the District notifies the applicant that the application has been granted. Permit fees for less than one year shall be prorated for the balance of the permit period (Jan1 through Dec. 31). By January 151

h of each year, all holders of an Authority to Construct or Permit to Operate shall be notified by the District of the annual renewal fee based upon the current fee schedules. The permittee shall pay the initial fee or the annual renewal fee to the District Office in person or by mail postmarked no later than 30 days after notification. If the fee is not paid within 30 days, it shall be increased by one half the amount thereof, and the District shall promptly notify the permittee by mail of the increased fee. If the increased fee is not paid within 60 days after such notice, the permit shall be immediately suspended and the District shall so notify the permittee by mail. Any suspended permit may be reinstated only upon payment in full of all accrued fees and penalties. [District Rule 3.1.8]

4. If any provision of this ATC/PTO is rendered void or unconstitutional by judicial or other determination, all other parts of these regulations which are not expressly held to be void or unconstitutional shall continue in full force and effect. [District Rule 1.5]

5. Any person building, constructing, erecting, altering, replacing, operating or using any article, machine, equipment or other contrivance, or multi component system, the use of which may emit air contaminants, or which may eliminate, reduce or control air contaminant emissions, shall first obtain written authorization for such construction from the Control Officer. [District Rule 2.1]

ATC/PTO 141203-BUG Crystal Geyser Water December 3, 2014 Page 2 ofS

(

6. A person who has been granted a Permit to Operate any article, machine, equipment, or other contrivance shall display such Permit to Operate, or an approved facsimile, in such a manner as to be clearly visible and accessible. In the event that the Permit to Operate cannot be displayed the Permit to Operate shall be maintained readily available at all times on the operating premises.

[District Rule 2.1C]

7. The "Right of Entry" as stipulated in California Health and Safety Code Section 41510, of Division 26, shall apply at all times.

8. The operator(s) of this facility shall comply with all applicable requirements pursuant to California Health and Safety Code, Part 6, Air Taxies "Hot Spots" Information and Assessment Act of 1987 (AB 2588) Sections 44300 through 44394, District Hot Spot Prioritization Guidelines, and District written requests.

9. All equipment installed for the purpose of controlling or abating emissions of air contaminants shall be maintained and operated in accordance with the manufacturer's specifications for optimum performance efficiency. No machinery shall operate unless all emission control systems are in place and properly operating. [District Rule 2.7]

10. No person shall discharge from any source whatsoever, such quantities of air contaminants or other material which cause injury, detriment, nuisance or annoyance to any considerable number of persons or to the public or which endanger the comfort, repose, health or safety of any such persons or the public or which cause, or have a natural tendency to cause injury or damage to business or property. [District Rule 4.2]

OPERATING CONDITIONS:

11. Breakdown Condition: For the purpose of this permit, a breakdown condition means an unforeseeable failure or malfunction of any air pollution control equipment or related operating equipment which causes a violation of any emission limitation or restriction prescribed by this permit, applicable rules and regulations, or by state Jaw. A breakdown shall be reported to the District Office as soon as reasonably possible, but no later than one (1) hour after its detection during a regular business day or one (1) hour after the start of the next business day, whichever is sooner. Report all applicable breakdowns to the District at (530) 841-4029 or (530) 841-4030. [District Rule 2. 12]

ATC!PTO 141203-BUG Crystal Geyser Water December 3, 2014 Page 3 ofS

(

12. In the event of any violation of District Rules and Regulations, the facility owner/operator shall cease operation of the violating equipment and take corrective action to end such violation. Once repaired or adjusted, operation of said equipment shall not commence until permit-operating condition #11 has been satisfied. [District Rule 2.12]

13. Maximum hours for testing and maintenance shall not exceed 50 hours per rolling 12-month period. If for some reason the 50 hours is exceeded, the District shall be notified by e-mail, fax or U.S. mail within 48 hours.

[CCR 93115.6(a)(3)(A)1.C]

EMISSIONS CONDITIONS

Generator

14. Except as provided in these conditions, a person shall not discharge into the atmosphere from any single source of emission whatsoever, any air contaminant for a period or periods aggregating more than three minutes in any one hour which is:

a. As dark or darker in shade as that designated as No. 2 on the Ringel mann chart as published by the United States Bureau of Mines.

b. Of such opacity as to obscure an observer's view to a degree equal to or greater than does smoke described in part "a" above. [District Rule 4.1]

FUEL REQUIREMENTS 15. As of September 1'\ 2006 the fuel used to power all diesel powered equipment shall

not exceed a sulfur content of 15 parts per million as required in the guidelines of Title 13, California Code of Regulations, Section 2281 and 2282, (Last amended August 14, 2004).

RECORD KEEPING CONDITIONS

16. The following records shall be continuously maintained for the duration of this permit and made available to the District upon request. These records shall be kept in a clear and concise format requiring the following data.

[District Rule 2. 7]

Subject Information required

Generator Daily hours of operation (Not required to report on those days the qenerator did not run)

17. Continued compliance with the District Rules and Regulations, and the California Health and Safety Code is required for this permit to remain in effect. [District Rule 2.7]

ATC/PTO 14!203-BUG Crystal Geyser Water December 3, 2014 Page 4 ofS

(

18. It is the owner/operator's responsibility to comply with all laws, ordinances and regulations of other governmental agencies, which are applicable to the equipment to be used. [District Rule 2.7]

19. This facility will be notified by January 15 of each year of the annual renewal fee based upon the current fee schedule. II is the facility owner/operator's responsibility to pay the required fee in a timely manner. Failure to pay fees may result in penalties or permit suspension. [District Rule 3. 1]

I have read and understand the above permit conditions.

Ow""'"'"'"" '''""'"'.;pr 9__Q Date 3-? -e/'-j!)

An Authority to Construct permit is hereby granted. Once construction is complete, the owner/operator shalf notify the District. Once notified, the District shalf inspect the operation for compliance with all applicable Jaws, rules and permit conditions. If compliance is determined, District staff shaff sign off on the Post Construction Inspection below, which will change the status of this Authority to Construct to a Permit To Operate.

Issue Date: / Ol -5"-I Y'

PATRICK J GRIFF Air Pollution C trol Officer Siskiyou County APCD

ATC!PTO 141203-BUG Crystal Geyser Water December 3, 2014 Page 5 ofS

(

COUNTY OF SISKIYOU AIR POLLUTION CONTROL DISTRICT

December 4, 2014

525 SOUTH FOOTHILL DRIVE

YREKA, CALIFORNIA 96097-3090

PHONE: (530) 841-4029 FAX: (530) 842-6690

Crystal Geyser Water Company Attn: Richard Weklynch P 0 Box 304 Calistoga, CA 94515-0304

Dear Mr. Weklynch:

Enclosed please find the Authority to Construct/Permit to Operate • ATC/PTO 141203-BUG

PATRICKJ. GRIFFIN AIR POLLUTION CONTROL OFFICER

This is for the Emergency Standby Diesel Generator at the following location: 210 Ski Village Drive Mt. Shasta, CA. If you have any correction or concerns I can be contacted at the phone number below. If not please sign and date page 5 of the permit on the "owner/operator signature" line and send a copy to:

Siskiyou County Air Pollution Control District 525 South Foothill Drive Yreka, CA 96097

Please call the District to schedule a post construction inspection upon construction completion. If compliance is determined District staff shall sign off on the Post Construction Inspection.

Thank you for your time.

~~JI~ Kimberly Sumner, Air Pollution Specialist Siskiyou County Air Pollution Control District 525 S Foothill Drive Yreka, CA 9609 530 841-4030



A. Use one application form for each permit unit of basic equipment and air pollution control equipment. This may include a single or multi-component system.

B. This application must accompany a Permit Application form. C. Each application must be filled out completely and accompanied by adequate plans and

operating characteristics. D. A responsible member of the organization that is to operate the equipment must sign

each application.

LEGALOWNER

l> Name:_Richard Weklych~-:-:::-:-+--=-~~~~~~~~~~~~~-l> Company:_Crystai_Geyser_Wat4r_Company ___________ _ l> Address:_21 O_Ski_ Village_Dr-t! _______________ _ l> City/Zip:_Mt._Shasta, CA_96~67 ____________ ~ l> Phone/Fax:_(530)918-9325_-;'---------------l> email:[email protected] ______________ _

OPERATOR

l> Name (Business License Name):_Crystai_Geyser_Water_Company __ _ l> Address (Physical address):_501_Washington St. ___ ~~----l' City/Zip:_Calistoga,CA_94515. _______________ _ l> Phone/Fax:_(707L942-0500 _______________ ~ l> e-mail:[email protected] ________ -:c:-_______ _

> Physical location (address) of the 1 generator:_21 O_Ski_ Village_Dr_Mt Shasta, CA 96067 .

I

LOCATION DATA EQUIPMENT

~ Drawing or sketch of proposed layout, showing the generator relative to buildings, streets, houses, etc.

(This part can be faxed back to the District on a separate sheet)

~ Distance (in feet) from the generator emission point to the closest:

School ft.: 3 J.. S"" 0

Hospital ft.: __ ___,3__....o::......:..o....:O:::..._ _____________ _

Daycare ft.: __ lf __ d-_s-:::..___o ____________ _

Resident ft.: ___ Cf~SI~O _____________ _

KOHLER. Power Systems

Model:

Nameplate BHP@ 1800 RPM:

Type:

Aspiration:

Compression Ratio

PERFORMANCE DATA: Engine bkW @ Stated Load

Fuel Consumption (g/kWh)

Exhaust Gas Flow {m3/min)

Exhaust Temperature (°C)

EXHAUST EMISSION DATA: HC (Total Unburned Hydrocarbons)

NOx (Oxides of Nitrogen as N02)

CO (Carbon Monoxide)

PM {Particular Matter)

100REOZJF 60HZ. DIESEL INDUSTRIAL GENERATOR SET

EMISSION DATA SHEET ENGINE INFORMATION

John Deere, 4045HF2851

158

4-Cycle, 4 Cylinder, lnline

Turbocharged, Charge Air-Cooled

19:1

1/4 Standby

29.50

272.10

Bore: 106mm (4.19 in.)

Stroke: 127mm (5.00 in.)

Displacement: 4.5 L {276 cu. in.)

EPA Family: EJDXL04.511 9

EPA Certificate: EJDXL04.5119-009

Table 1

1/2 3/4 Full Standby Standby Standby

59.00 88.50 118.00

254.70 237.40 222.40

22.80

580.00

Table 2

EPA CERTIFICATE DATA

0.15

3.4

1.3

0.17

Values are in g/kWh unless otherwise noted

TEST METHODS AND CONDITIONS The EPA Certificate Data in Table 2 is a weighted average value per ISO 8528 D2.

Data and specifications subject to change without notice For further information, please contact Todd Loes at John Deere Power Systems, 319-292-6050

--~

.. o.~'''"'-~· f ~\ 'i: ~l

~"' pR(f'f<d',;

UNITED STATES ENVIRONMENTAL PROTECTION AGENCY 2014 MODEL YEAR

CERTIFICATE OF CONFORMITY WITH THE CLEAN AIR ACT OF 1990

OFFICE OF TRA.I'ISPORTATION AND AIR QUALITY

ANN ARBOR, MICHIGAN 48105

Certificate Issued To: Deere & Company (U.S. Manufacturer or Importer)

Certificate Number: EJDXL04.5119-009

Effective Date: 09/10/2013

Expiration Date: 12/3l/2014

/4;~~ Issue Date: 09/10/2013

Revision Date: N/A

I Model Year: 2014 Mobile/Stationary Indicator: Stationary

Emissions Power Category: 75<=kW<130 Fuel Type: Diesel

j Manufacturer Type: Original Engine Manufacturer Engine Family: EJDXL04.5119

I

After Treatment Devices: No After Treatment Devices Installed Non-after Treatment Devices: Non-standard Non-After Treatment Device Installed, Electronic Control, Smoke Puff Limiter, Engine Design Modification

Pursuant to Section 111 and Section 213 of the Clean Air Act ( 42 U .S.C. sections 7411 and 754 7) and 40 CFR Part 60, and subject to the terms and conditions prescribed in those provisions, this certificate of

conformity is hereby issued with respect to the test engines which have been found to conform to applicable requirements and which represent the following engines, by engine family, more fully described in the documentation required by 40 CFR Part 60 and produced in the stated model year.

This certificate of conformity covers only those new compression-ignition engines which conform in all material respects to the design specifications that applied to those engines described in the documentation required by 40 CFR Part 60 and which are produced during the model year stated -On ~is -certificate of the said manufacturer, as defined in 40 CFR Part 60.

It is a term of this certificate that the manufacturer shall consent to all inspections described in 40 CFR 1 068-and authorized in a warrant or court order. Failure to comply with the requirements of such a

warrant or court order may lead to revocation or suspension of this certificate for reasons specified in 40 CFR Part 60. It is also a term of this certificate that this certificate may be revoked or suspended or rendered void ab initio for other reasons specified in 40 CFR Part 60.

This certificate does not cover engines sold, offered for sale, or introduced, or delivered for introduction, into commerce in the U.S. prior to the effective date of the certificate.

AUTHORITY TO CONSTRUCT/ PERMIT TO OPERATE PERMIT FOR

FIRE PUMP GENERATOR

Siskiyou County APCD ATC I PTO Application Received

APR 1 ti 2014

~

County of Siskiyou .,,_ '

Air Pollution Control District 525 South Foothill Drive

Air PoiiU!iOn Contrciiolstllct

Yreka, California 96097 Phone#: (530) 841-4029; 841-4031 Fax#: (530) 842-6690

Permit Application For: ·New Construction D

D D 0

Authority To Construct (ATC) Authority To Construct (ATC) Authority To Construct (ATC) Permit to Operate CPTO)

·Modification of Emission Unit to a Valid PTO/ATC

·Change ofLocation

·ownership change

1. PERMIT TO BE ISSUED TO: Crystal Geyser Water Company

2. MAILING ADDREss: Crystal Geyser Water Company

STREET I P.O Box: PO Box 304

CrTY: Calistoga STATE' CA ZIP CODE: 94515-0304

3. LoCATION WHERE THE EQUIPMENT WILL BE 0PERA1'llD: Within 1,000 ft of a school? STREET 21 0 Ski Village Drive CITY: Mount Shasta OYes!ZINo

S.I.C. Code of Facility: SECTION: 9 TOWNSHIP: 40N RANaE:4W

Proposed install date: Proposed

4. GENERAL NATURE OF BUSINEss: Beverage Bottling Completion date:

5. DESCRIPTION OF EQUIPMENT OR MODIFICATION FOR WHICH APPLICATION IS MADE: (INcLUDE ADDITIONAL

SHEE,'SABNESSECCARY) PTO 091405 Fire Pump Engine (existing, ownership change)

6. HAVE YOU EVER APPLIED l<~OR AN ATC OR PTO IN SISKIYOU COUNTY?0 N<0 YES, IF YES, PERMIT#:

7. IS THIS PROPERTY ZONED PROPERLYFORTHISPERMIT? 0 NO 0YES, IF YES, ZONE conE#: M-M

8. Is THE EQUIPMENT REGISTRED WI'l'H CARE.? IZ!No DYEs, IFYJ<:s, REG.#:

9. TYPE oF ORGANIZA'rioN: CoRPORATION, 0 PARTNERSHIP, 0INDIVIDUAL, OGoVERNMEN'l' AGENCY, D

10. TYPE OR PRJNT NAME OF APPIJCANT: Richard Weklych T!TI,E OF APPLICANT: EVP Manufacturin~

l~p7t/ DA4/r/rf PHONE#: 707-942-0500 FAX#:

E·MATL' [email protected]

(..· ~ 7 A $50.00 filing fee must accompany each application/a (District rule 3.1 Permit Fees) Date paid: 4/--/ b • lt.j For transfer of ownership or location a $20.00 transfer fee must accompany application (District rule 3.1 Permit Fees) Date: -Make check payable to: Siskiyou County Air Pollution Control District.



April21, 2014

525 SOUTH FOOTHILL DRIVE

YREKA, CALIFORNIA 96097-3090

PHONE: (530) 841-4029 FAX: (530) 842-6690

Crystal Geyser Water Company Attn: Richard Weklynch P 0Box304 Calistoga, CA 94515-03 04

Dear Mr. Weklynch:

PATRICK J. GRIFFIN AIR POLLUTION CONTROL OFFICER

Enclosed find the Permit to Operate (PTO 140421) for the Fire pump at the Ski Village Drive site in Mt. Shasta, California. Please sign page 5 of the permit on the "owner/operator signature" line and send a copy of that page to:

Siskiyou County Air Pollution Control District 525 South Foothill Drive Yreka, CA 96097

or e-mail to; [email protected]

Also enclosed is a pro-rated annual permit fee for the balance of2014. See General Conditions #3 of your pennit.

Please call the District to schedule an inspection upon start up. If compliance is determined District staff shall sign off on the permit, which will validate the status of this Permit to Operate.

Thank you for your time.

Sincerely,

~e-t_ Kimberly Sumner Air Poiiution Specialist Siskiyou County Air Pollution Control District

I I


525 SOUTH FOOTHILL DRM YREKA, CALIFORNIA 96097-3090 PHONE' (530) 841-4029 FAX: (530) 842-6690

Permit to Operate IS HEREBY GRANTED TO

CRYSTAL GEYSER WATER

PTO 140421 (Cummins Fire pump Engine)

Owner Crystal Geyser Water Company

P 0 Box 304 Calistoga, CA 94515-0304

(707) 942-0500 [email protected]

Operator Crystal Geyser Water Company

P 0 Box 304 Calistoga, CA 94515-0304

(707) 942-0500 [email protected]

EQUIPMENT LOCATION: 210 Ski Village Drive, Mt Shasta

PATRICK). GRIFFIN Air Pollution Control Officer

EQUIPMENT DESCRIPTION: Backup Cummins Firepump Engine, Modei6BTA5.9-F4.

PTO 140421 Crystal Geyser Water

Type: 4 cycle, In-line, 6-cylinder diesel, 160-bhp

Se.-~ wo. 4c..6~DC.~

04/21/2014 1 of 4

PERMIT CONDITIONS:

This Permit to Operate (PTO) allows the legal owner/operator to construct and then operate a Water Bottling facility using the devices listed on the title page of this document according to the following provisions.

GENERAL CONDITIONS:

1. Conditions contained in this PTO are intended to assure that components of this facility are designed and operated in compliance with all Siskiyou County Air Pollution Control District (District) Rules and Regulations. The District reserves the right to amend this permit, if the need arises, to insure compliance of this facility or to abate any public nuisance. The legal owner/operator is also responsible for compliance with all other District, state and federal regulations not noted in this permit. [District Rule 2.7, 4.2, 2.10]

2. This PTO shall not be transferable, whether by operation of Jaw or otherwise from one location to another, from one person to another, or from one piece of equipment to another, except on written approval of the Control Officer. [District Rule 2.3]

3. Initial permit fees based upon the current fee schedules shall become due when the District notifies the applicant that the application has been granted. Permit fees for Jess than one year shall be prorated for the balance of the permit period (Jan1 through Dec. 31). By January 151

h of each year, all holders of an Authority to Construct or Permit to Operate shall be notified by the District of the annual renewal fee based upon the current fee schedules. The permittee shall pay the initial fee or the annual renewal fee to the District Office in person or by mail postmarked no later than 30 days after notification. If the fee is not paid within 30 days, it shall be increased by one half the amount thereof, and the District shall promptly notify the permittee by mail of the increased fee. If the increased fee is not paid within 60 days after such notice, the permit shall be immediately suspended and the District shall so notify the permittee by mail. Any suspended permit may be reinstated only upon payment in full of all accrued fees and penalties. [District Rule 3.1.8]

4. If any provision of this PTO is rendered void or unconstitutional by judicial or other determination, all other parts of these regulations which are not expressly held to be void or unconstitutional shall continue in full force and effect. [District Rule 1.5]

5. Any person building, constructing, erecting, altering, replacing, operating or using any article, machine, equipment or other contrivance, or multi component system, the use of which may emit air contaminants, or which may eliminate, reduce or control air contaminant emissions, shall first obtain written authorization for such construction from the Control Officer. [District Rule 2.1]

PTO 140421 Crystal Geyser Water 04/21/2014 2 of4

6. A person who has been granted a Permit to Operate any article, machine, equipment, or other contrivance shall display such Permit to Operate, or an approved facsimile, in such a manner as to be clearly visible and accessible. In the event that the Permit to Operate cannot be displayed the Permit to Operate shall be maintained readily available at all times on the operating premises. [District Rule 2.1C]

7. The "Right of Entry" as stipulated in California Health and Safety Code Section 41510, of Division 26, shall apply at all times.

8. The operator(s) of this facility shall comply with all applicable requirements pursuantto California Health and Safety Code, Part 6, AirToxics "Hot Spots" Information and Assessment Act of 1987 (AB 2588) Sections 44300 through 44394, District Hot Spot Prioritization Guidelines, and District written requests.

9. All equipment installed for the purpose of controlling or abating emissions of air contaminants shall be maintained and operated in accordance with the manufacturer's specifications for optimum performance efficiency. No machinery shall operate unless all emission control systems are in place and properly operating.

[District Rule 2. 7]

10. No person shall discharge from any source whatsoever, such quantities of air contaminants or other material which cause injury, detriment, nuisance or annoyance to any considerablenumber of persons or to the public or which endanger the comfort, repose, health or safety of any such persons or the public or which cause, or have a natural tendency to cause injury or damage to business or property. [District Rule 4.2]

OPERATING CONDITIONS:

11. The facility manager shall follow the procedure that is described in District Rule 2.12 regarding upset/breakdown conditions and excessive emission reporting.

12. The facility owner/operator shall comply with all District, State, and Federal air pollution regulations. Special care should be exercised to avoid any violation of District Rule 4.1 Visible Emissions and District Rule 4.2 Nuisance.

13. In the event of any violation of District Rules and Regulations, the facility owner/operator shall cease operation of the violating equipment and take corrective action to end such violation. Once repaired or adjusted, operation of said equipment shall not commence until permit-operating condition #11 has been satisfied.


14. Maximum hours of operation shall not exceed 200 hours/calendar year.

15. Testing hours shall be Monday through Saturday between the hours of 8:30am to 5:00pm.

FUEL REQUIREMENTS

16. As of September 1 '', 2006 the fuel used to power all diesel powered equipment shall not exceed a sulfur content of 15 parts per million as required in the guidelines of Title 13, California Code of Regulations, Section 2281 and 2282, (Last amended August 14, 2004 ).

RECORD KEEPING

17. The following records shall be continuously maintained onsite for the duration of this permit and made available to the District upon request. These records shall be kept in a clear and concise format requiring the following data.

Subject Information to be recorded

Cummins Fire pump/Engine a. Date/Time/Hours of operation

b. Reason for operation.

• Pest CeRstniGti9R Inspection: Date .3 -W--f6" Continued compliance with the District es and Re ulations and the California Health and Safety Code is required for this permit to remain in effect.

It is the owner/operator's responsibility to comply with all laws, ordinances and regulations of other governmental agencies, which are applicable to the equipment to be used.

This facility will be notified by January 15 of each year of the annual renewal fee based upon the current fee schedule. It is the facility owner/operator's responsibility to pay the required fee in a timely manner. Failure to pay fees may result in penalties or permit suspension.

I have read and un?erstood ~6# peqnit~:s[ ~ , / ~~ jd Owner/operators1gnat~ ~ ~, Date ~p

Issue Date: ~/i(

Air Pollution Con rol Officer


Emissions Data

\Jh \l~ I) I) lJ ~ l.IJ

GENERATOR APPLICATIONS POWERTECH ENGINES

'OWERTECH ENGINE EMISSIONS DATA

Some of our published data is derived from measured data on almllar engines. Data applies to Steady state oper<~tion of the engine at lull load (standby) and rated speed. NOx. HC .• oo··!lnd Pm are measured per ISO 6176·1.

We da not certify that each engine Will meet these emissions level& ..

These emiSsions values cannot be compared to GARB, EPA, and Eu~11n tJOn•road reg~lations. which are based upon a weighted average ~~the emtssr_ons at OiJngine o rating ~lnts :.llw;~ratlng pomts tor genera!ors, eight o;wAting potnts tor tndustnat). Compliance wtth CARr EPA. or Euro an.non·roaa emi5Sion regulattons ts denoted by an emtssions label on the engtno.

Engine Model Gen Set Power NOx -~ co Pm Applic:allon bhp(kW) ®rpm . glhphr(fllhr) · ., Qntphi'(Oillr) . •fVhphr(g/llr) ghlphr(g/hr)

... Prime I 64(48) ® fl.lOO 6.33 (406) .· 0.16'(10) 0.83 (53) 0.13(8)

4045DF1SO Standby 71(53)@1800

' 6.01 j427)". 0;06 (4) 2.40 (170) 0.36 (26)

Prime I 9o(e7)@1aoo"· ---- 7.83 "(70S) · · '.0.28c(25) 0.19 (17) 0.05 (5) 4045TF150

Standby 100(75)@1800 8.51 (851) •. 0.20.(20) 0.23 (2S) 0.06 (8) f--

Prime 99(74)@1800 7.57 (766) 0.28~2$) .. 0.19 (17) 0.05 (5) 4045TF150 --1---

Standby 110($2)@1800 8.64 (ll50) 0~0 (20) 0.23 (23) 0.06 (6)

Prime i0?(7e)@180o 8:34 (851) ;, ·oi2B.(26) 0.21 (21) Q;04 (4) 4045TF250

Standby ' 113(64)@ 1800 9.29 (1060) 0.19 (21) 0;34 (3!1) om (8)

Prime 110(82)@1800 7.68 (855) 025(26) 0.21 (21) 0.04 (4) 4045TI'250 -

Standby i 122(91)@1800 8.56 (1038) . 0.19 (21) 0.34 (38) O.o? (6) ·-·~--" ---~

7.64 (902)> · .. Prime 115(85)@1800 0;16;!18) 0.21 (24) 0.065 (7) 4045HF150

. ·,

Standby 127(95)@ 1 BOO a.se (1011Ql. Q;1~ (19) 0.24 (30) 0.008 (9)

Prime 149(111)@1MOO !>.23 (78&) . .. 0.115 (18) 0.21 (24) 0.065 (7) 4045HF150 '

Standby i 16S(123)@1SOO 5.61 (923) - -MS (1g) 0.24 (30) 0.088 (9)

Prime I 135(101)@1800 7.71 (IQ41) . 0.33 (45) 0,42 (57) 0.09 (12) 606BTF150

Standby t50(1121@1800 a.se (1300) 0.06 (9) 0.30 (45) 0.13 (20)

Prime 14G(t11)@1800 6.67 (1014) ... ().33(45) 0.42 (67) 0.09 (12) 6068TF150

Standby 165(12:l)®1BOO 7.59(1259). o:oli.(Bl 0.30 (46) 0.13 (20)

Prime 1 150(112)@1soo 8.74 (1311) 0;27(41) 0.41 (62) 0.08 (13) 606BTF250 ,. Standby 166(124)11'111800 9.01 (14~). 0,()8(13) 0,31 (5-1) 0.12 (20)

Prima i 172(128)@1800 7.00 (1221) o:27·141l 0.41 (62) 0.08 (1~) 6068TF250

Standby 190(1~2)@1800 e.oo ll6Z7l 0.08(13) 0.31 (51) 0.12 (20) -- ..

Conrlnuet1 -

M~rch :woo G1 • 7 Engine Performanco Cu!Ves

____ ,. _____ , Engine

-·---------· DEERE POWER SYSTEMS GROUP

NUMBER: EIB00-16

DATE: 15 March 2000

SUBJECT: SCAQMD CERTl:JrJ:I!l]) llQtJ:r:PMJJ:m :PI:IWJ:'l'S : EMERGENCY STANDBY Gl!lNilRA'l'Oit DRXVE llNG:tNI!:B

We have been notified by SCAQMD that ten CEPs for twenty-five POWERTECH model ratings and the 6101HF010 have been renewed. The renewed permits are valid for oneyear from the renewal date. Renewed and current CEPs apply.to. the following Generator Drive Engines and ratings: ·

SCAQMD Certified llquiplaent Pa:rmit Horse Power @ 1800 rpm

71 100 110 113 122 127 150 165 165

l!lngina Model

4045DF150 4045TF150 4045TF150 4045TF250 4045TF250 4045HF150 6068TF150 4045HF150 6068TF150 6068TF250 6068TF250 6068HF250 6081TF001 6081AF001 6068HF150 6081TF001 6081AF001 6081HF001 6081AF001 6125AF001 6101HF010 6125AF001 6081HF001 6125AF001 6125HF001 6125HF001

AppliqatioQ No• Rais•ll•l+••ua DatT 320203 February 01, 2000

-166 190 198 211 250 251 260 300 322 347 375 402 402 413 442 483 563

' Expires February 01,2001 ' Expires February 03,2001

320202 February 01, 2000 1

320202 .· February 01, 2000 1

320.202 February 01, 2000' 320202 February 01, 2000' 3'22365 February 01, 20001

32020.1 February 01, 2000 1

322365 February 01, 2000' . 320201 February 01, 20001

)20201 February 01, 2000' 320201 February 01, 2000' 322366 February 01, 2000' 308884 February 01, 2000' 308886 February 01, 2000' 322366 February 01, 2000' 308884 February 01, 2000' 308886 February 01, 2000' .'308885 February 01, 2000' 308886' February 01, 2000' 33 6112 February 03, 2000' 308D81. February 01, 2000' 336112 February 03, 2000' 308885 February 01, 2000' 336112 February 03, 2000' 336113 February 03, 2000' 336113 February 03, 2000'

EIB00-16 15 March 2000 Page 2

Certified Equipment Permits (CEP) apply only to emergency standby engines used as a temporary·power source for less than 200 hours per year. In addition, the generator set operator must agree to conditions set forth.on the CEI?. Using one of these CEPs to obtain a SCAQMD Permit .to Construct and Operate will expedite processing at SCAQMD and result in.a reduced SCAQMD processing fee. (Note: The fee as of July 01, 1999 for permit submittal through the .SCAQMD Registration Program was $155.10.)

SCAQMD also offers over-the-counter permitting for emergency standby engines with CEPs at their District Headquarters lobby (permits generally issued within one hour).

Complete Permit to Construct and Operate application packets for CEP installations can be obtained by contacting SCAQMD at (909) 396-2466 or {909) 396-2547.

Electronic reproductions of the. ·e.leven '(twenty-six ratings) reissued CEPs are attached to this ·bulletin. They will be placed in the Engine Application document titled "SCAQMD Permits".

Legal Owner or Operator:

(

SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT

21865 East Copley Drive, Diamond Bar, OA 91765

CERTIFIED EQUIPMENT PERMIT

Renewed as Of.February 1, 2000

DEERE POWER SYSTEMS GROUP P.O. BOX SHXl WATERLOO, lA 50704 A TIN: RICHARD BISHOP

JD 092796

Equipment Location: SAME AS ABOVE

The equipment described below and as shown on the approved pllllls.&itd .apiicll'ieatlons are subject to the special condition or conditions listed.

Equipment Description

Applicotion No. 320201 Page 1

INTERNAL COMBUSTION ENGINE, JOHN DEERE. 6 CYL!Ni>ER;; TURBOCHARGED, MODEL 6068T, 150 BHP ( 165 BHPl (166 BHP) (190 BHP), DIESEL-FUELED. DRIVING A:~LBMER;oENCY ELEcrRICAL GENERATOR. ' / .

Manufacturer Condition

I. THIS CERTIFIED EQUIPMENT PERMIT SHALL t-/OlRBL)BVE THE PERSON CONSTRUCTING, INSTALLING OR OPERATING THE EQUIPMENT AT EACH SPECIFIC SITE FROM THE REQUIREMENT TO OBTAIN ALL NECESSARY :PJ31iMtTS''rQ CONSTRUCT AND OPERATE OR, FROM COMPLIANCE WITH ANY OTHER DlSTRICTi~ui.ES INCLUDING THE REQ1i1REMENTS OF REGULATION X!ll.

End User Conditions

I. A TIMER SHALL BE MAINTAINED TO JNDJCA'JlB:tlmE.NGlNE ELAPSED OPERATING TIME.

2. THIS ENGINE SHALL NOT OPh'RA TE MORE TliAN>l99 HO'ORS IN ANY ONE YEAR

3. AN ENGINE OPERATING LOG LISTING THe DATE OF OPERATION, THE ELAPSED TIME, IN HOURS, AND THE REASON FOR OPERATION SHALl;. ';BE KEPT AND MAINTAINED ON FILE FOR A MINIMUM OF TWO YEARS AND MADE AVAILABLE TO DISTRICT PERSONNEL UPON REQUEST.

4. SULFUR CONTENT OF DIESEL FUEL SUPPLIIID:TO THE.:ENOINE SHALL NOT.EXCEED 0.05% BY WEIGHT.

Please notify RAMAN PATEL at 9091396-2466 when SCAQMD.Informalion packets are needed or if you have any questions concerning the Certification/Registration Program. ·

ORIGINAL(copy)

SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT

21865 East Copley Drive, Oiamond·~;~ar, CA 91765

CERTIFIED EQUIPI\I~~T ~ERMIT

Application No. 320201 Page2

This Certified Equipment .Permit is based on the plan.,, spcciticlltions. and dnta submitted a~ it pertains to the release of air contaminants and control measures to reduce air contaminants. ·.No approval or opinion concerning safety and other !'actors in design. construction ur operntion nf the equipment is expressed or implied.

This Certified Equipment Permit wi II hecnme invalid if this npplicatiort is canceled, THIS PERMIT SHALL EXPIRE ONE YEAR FROM THE DATE OF ISSUANCE unless nn extension is granted by the Executive Officer.

ORIGINAL (copy) ·

Feb 27 01 12: lOp Aq~ Fire Protection ~'41 8587

'Sent By: George E. Swett & Co., ( ., 650 365 6256; ""!PIR'*!f 't

559 (

Feb-27-01 · .49AM; Page 2/2 z v ·nwr 'P!I IW 6* FES-27-01 TUE 12:40 PM PATTERSON PUMP CO FAX NO. 706 886 0023

Cummins Engine Company, Inc. Exhaust Emissions Data Sheet

I 4§4

P. OJ

FireJJtJrtP

"" No. FP 7 """'

Engine Model: 6DTA5.9-F4 Type: 4 cycle, In-Line, 6 Cylinder Diesel Aspiralion: 'fllrbochnrged illld Afrorcooled Coonprcsslon ltatio: 15.5: 1 En1issions C'olllrol Devire: Thrbo, Aliercooling

l!erformance Data 1mr Fuel Cons ..... ption (.gallons/hour) A it to Fu~l Rallo Exhaust Gas Flow (CFM) Exhaust Gas 'fcmpernlure (~

Application: Cunfig. Number; Bore: Stroke: Displacement:

21QQ BeM 160 8.2

:lS.S 843 763

Data Sheet: DS·90300 Dale: 12May97

Firepump D403018PX02 4.02 in. ( 102 mm) 4.72 in (120mm) )$9 cu. in. (S,9litcrs)

1160 BfM 140

6.9 20.9

559 8l8

Exhaust Emissions Data (All values ;ue gramslhp-hnur)

Qomponell1 IIC (To~•! Unbumod HydrllCarbons) NOx (Ol!idcs ofNiuugcn as NOV CO (Catbon Monoxide) I'M (l'.uticulate Matter)

SOz (Sulfur Dioxide)

COz (C;uboo Dioxide) Nz (Nib·ogcn) Oz (Oxygen) llzO (Wllltr V•opor)

Test Conditions

2:1QI:l BE!M 1.64 3.97

2.87 0.25 0.64 ):15

3150

410 195

tz6D BI:!M 1.12 5,38

!.49 0.25 0.63

515

2600 240 190

D:1L1 w~s recorded during stoady-stafll rated engine speed (:l- 2S RPM) with fulllood (± 2%). l>re·ssurcs, tcmpet"\Ul'CS, ruu.l emission rate~ were stabili7.cd.

f."uel Spoou~ration: ASTM P975 No. 2·D diesel fuel wilh 0.2% sulfur content

llucJ"femp~rature: J ntilkC Air Tempera tor~: BQII'Omctrie l'ressure: llumitlity:

(by wci8ht) and 42·50 ctlmo n\lmber. 990F±9°(at fuel pump inlet) 7T'F±9° 29.6 in. Hg ± l in. llg NOK moosuremont con-ected to 75 gmins B:<(>/lb. dry nir

TI1~ IIC, NO~. nnJ (.'0 C'll\i:.;.~.lom dnt:l 1abt,1altd hel-e wue ~.:~ltD holm~,~ t"ingh: t:ll81P~otvn&kr lhc 1es1. condJ!Jsm~ !1\lliNJl atmvt. nun forlh~ olh~.-

r••\

fOillnJMntnl$ <Ire Ctl~lllo1h·'"· l'his 1.IUI.U is '!;llbjl:tliO inslntfflfiiU\liCII, IMO'ISDI"ertlenl, Md t:nR(niH .. eng:lrll!'V~I)bilU)'. FllClnt Of'tta\iGn W ilh l!:kCCS~ .,--. ..

ri~ll! ai.- inbltl! (frcdo:t .. ~' ,,l:aricllon beyond pll~lltll«< tilaAita\lm.l!mhs,lH will\ it'tlpfop-'1 rn;dq«;nwn:c, milY resun in tl~attd tmi!l:~:.i!)n •~vds.

Daw ShuJ : DS-90306

Cl.JMMINS t~NGINE COMPANY; INC., Cotunfbns., IN 472()2..)005 U.s.A.

p.2

J

PERMITS AND PERMIT APPLICATIONS TO THE AIR DISTRICT …...Maximum hourly fuel usage 7.089 MMBtu/hr...

Documents

Transcript of PERMITS AND PERMIT APPLICATIONS TO THE AIR DISTRICT …...Maximum hourly fuel usage 7.089 MMBtu/hr...