Pelco PMCQ14A 14-Inch Color Quad Monitor Manual

PMCQ14A14-Inch ColorQuad Monitor

Installation/Operation Manual

C1970M-A (7/01)

Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120

®

CH1 CH2

CH3 CH4

2 Pelco Manual C1970M-A (7/01)

CONTENTS

Section Page

IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3DESCRIPTION ...................................................................................................................4

FEATURES ................................................................................................................4OVERVIEW ................................................................................................................4

INSTALLATION ..................................................................................................................6PROGRAMMING ...............................................................................................................7CHECK OUT ......................................................................................................................8OPERATION ......................................................................................................................8

DISPLAY ....................................................................................................................8INTERCOM ...............................................................................................................10ALARM ...................................................................................................................... 11VCR RECORD/PLAYBACK ...................................................................................... 11

TECHNICAL SPECIFICATIONS ....................................................................................... 14REGULATORY NOTICES ......................................................................................... 15

WARRANTY AND RETURN INFORMATION.................................................................... 16

LIST OF ILLUSTRATIONS

Figure Page

1 Typical Application Using PMCQ14A Monitor .................................................... 52 Examples of Camera Locations .........................................................................53 Monitor Connections ..........................................................................................64 Control Locations on Front of Monitor ................................................................ 75 Display Selections ..............................................................................................96 Intercom Activities on Screen ............................................................................ 107 Alarm Activities on Screen ................................................................................ 118 Monitor Back Panel Controls and Connections ................................................ 129 Monitor Controls ................................................................................................13

LIST OF TABLES

Table Page

A Programming Menu ...........................................................................................7B Check-Out Procedure ........................................................................................8C Display Functions ...............................................................................................8D Intercom Function ............................................................................................. 10E Alarm Function .................................................................................................. 11F Back Panel Reference Key ............................................................................... 12G Front Panel Reference Key ............................................................................... 13

Pelco Manual C1970M-A (7/01) 3

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel andconform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6Penclosure, it is designed for indoor use only and it must not be installed whereexposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. When used with the CCQ1400A-4 camera with audio, the PCMQ14A Color QuadMonitor is capable of being used as a two-way intercom system. Applications otherthan the intended use as a two-way intercom communications system may violateFederal wiretapping laws. No systems may be used to monitor audio without theexpressed knowledge of the parties being monitored. A warning notice must beposted and plainly visible at all entrances to public and private premises utilizing thePMCQ14A/CCQ1400A-4 intercom system. Pelco assumes no liability for equipmentbeing used for purposes other than the intended use as a two-way intercom system.

5. Do not attempt to disassemble the unit.

6. Do not remove screws or cover.

7. There are no user-serviceable parts inside.

8. Allow adequate air circulation to prevent internal heat build-up. Do not place the uniton or near materials that may hinder air circulation.

9. Do not install any of the system parts where they will be exposed to water, excessivedust or excessive vibration.

The product and/or manual may bear the following marks:

Please thoroughly familiarize yourself with the information in this manual prior to installationand operation.

This symbol indicates thatdangerous voltage constituting arisk of electric shock is presentwithin this unit.

This symbol indicates that thereare important operating andmaintenance instructions in theliterature accompanying this unit.

C A U T I O N :

RISK OF ELECTRIC SHOCK.DO NOT OPEN.


DESCRIPTION

FEATURES

• Observe up to Four Camera Images at Once or in Sequence• Programmable Dwell Time for Each Camera During Sequence Mode• Picture-In-Picture (PIP) View in Horizontal or Vertical Format• 2X Digital Zoom and Freeze Functions• Alarm Inputs for Each Camera Channel on Back of Monitor• Alarm Causes Channel to Come up with Full View• Programmable TTL Compatible Alarm Output on Monitor• Video Loss Detector Sets Alarm Beep• 4 Camera Inputs Through Mini-DIN or BNC Connectors• Looping Outputs When Mini-DIN Connectors Are Used• Common Video Output Through MONITOR OUT BNC Connector• Impedance Switches for Channel and Common Video Output Terminations

OVERVIEW

The PMCQ14A Color Quad Monitor is the ideal choice when you need an easy-to-installvideo surveillance system for viewing up to four areas at once. Cameras of your choice oralternate video sources (such as VCRs) can be used.

All monitor controls are located on the front of the unit. An observer can change the displayto zoom in on a single camera with the touch of a button. Camera ID is displayed on thescreen and is easily programmed.

In addition to its video capabilities, the monitor offers alarm and intercom features. Thealarm lets you install a “call” button near the camera so that a person on camera can getthe attention of the observer. The monitor has audio intercom capabilities that function onlywhen CCQ1400A-4 cameras are used.

VCR connections are provided for recording cameras.

Alarm connections are provided on the back of the monitor. These connections serve asinputs to connect alarm contacts directly to the monitor when using a camera without alarminputs. If not used as inputs, they can be used as outputs to provide a TTL compatibleinterface for operating alarm annunciators or other notification devices. Connections areeasily made via push-in type wire connectors. An alarm trigger output is also provided onthe push-in type wire connector. This can be used to automatically start a VCR when analarm occurs.


Figure 1. Typical Application Using PMCQ14A Monitor

EH3500IMAGEPAK OUTDOOR W/ HEATER & DEFROSTER

WCS1-4POWER SUPPLY

EH100IMAGEPAK INDOOR

MCS4-2POWER SUPPLY24 VAC TO ALL INDOOR CAMERAS

DF5 PENDANTDOMEPAK INDOOR

DF5 IN-CEILINGDOMEPAK INDOOR

TLR2024VIDEO CASSETTE RECORDER

PCMQ14A

CH1 CH2

CH3 CH4

CH4

CH2

CH3

CH1

Figure 2. Examples of Camera Locations

CH 1 BACK DOOR CH 2 FRONT DOOR

CH 3 STOCK ROOM CH 4 CASH CHECKOUT

CH 1 CH 2

CH 3 CH 4


INSTALLATION

1. Place monitor on a stable surfacesuch as a shelf or desk top.

2. Connect cameras or alternate videosources to the desired channelIN/OUT connectors on the back ofthe monitor (refer to Figure 3).

3. Set impedance switches to the75-ohm position (refer to Figure 3).

4. If alarm contacts are used, run wiresfrom the contacts to the monitor andconnect at the push-in connector onthe back (refer to Figure 3).

5. If used, connect a VCR to the VIDEO/AUDIO IN/OUT jacks and/or MONITOR OUTconnector, depending on the type of connectors on the VCR (refer to Figure 3). IfMONITOR OUT is not used for a VCR, another monitor can be connected. If MONITOROUT has equipment connected to it, set the impedance switch to HI. If MONITOR OUTis unused, set the switch to 75 ohms.

6. Plug in the power cord (refer to Figure 3).

7. Turn on MAIN switch on the back of the monitor (refer to Figure 3). Then press thePOWER button on the front of the monitor.

8. The monitor begins operation using the factory set defaults. To re-program the monitorfollow the procedure in Table A in the Programming section.

9. Test according to the check-out procedure in Table B.

BE SURE THERE IS AIR SPACE BELOW MONITOR.DO NOT BLOCK AIR SPACE BY PLACING MONITOR ON ASOFT SURFACE OR BY COUNTERSINKING SPOTSFOR THE FEET.

Figure 3. Monitor Connections

MAIN

A/C INLET

CH 1

IN

IN/OUT

CH 3 CH 4CH 2

REMOTE*CH 1 CH 2 CH 3 CH 4 TRIG

OUT

IN

OUT

MONITOROUT

VIDEO AUDIO

75 Hi 75 Hi 75 Hi 75 Hi 75 Hi

SCREEN

FOCUS

TO ACOUTLET

TO/FROM VCR

TO VCRTRIGGER

ALARM CONTACT

CAMERA OR ALTERNATEVIDEO SOURCE 1

*NOT USED IN STANDARD INSTALLATION. CONTACT PELCO IF REMOTE CONTROL IS REQUIRED.

AC TRANS-FORMER




24 VAC

TO VCR OR MONITOR(VIDEO ONLY)

TO 24 VAC TO 24 VAC

NOTE: The mini-DIN (IN)connectors are for use withCCQ1400A-4 cameras.


PROGRAMMING

QUADMENU

CH4VCR

PIPSEQ

CH3

ZOOMFREEZE

CH2

RESETALT

CH1 TALKAUDIO

MIC

TINT SHARP COLOR BRIGHT CONTRAST VOLUME POWER

FRONT PANEL PROGRAMING BUTTONS

RETURNS TO DEFAULT(ALT+MENU ENTERS/EXITS SETUP MENU)

Figure 4. Control Locations on Front of Monitor

Table A . Programming Menu

Press ALT + MENU to toggle in or out of the programming menu.

Menu Item Function Procedure

[1] Change channel name that a. Press CH1 (1 flashes yellow and the first character in the CH1ID INPUT appears on the screen. description turns yellow).

b. Use the up and down arrows (CH1 and CH2 buttons) to change acharacter. Up advances it through the alphabet, then the numbers, andfinally the ASCII symbols. Use the left and right arrows (CH3 and CH4buttons) to advance to the next or return to the previous characterposition.

c. When you have finished with CH1, press the right arrow until the firstcharacter of CH2 turns yellow.

d. Continue to change characters and advance through the channels untilall desired channel names are entered.

e. Press RESET.

[2] Change date and time that a. Press CH2 (2 flashes yellow and YEAR in the date field turns yellow).DATE-TIME appears on the screen. b. Use the up and down arrows (CH1 and CH2 buttons) to change the

YEAR.c. Use the right arrow (CH4) button to advance to the MONTH position.d. Use the up and down arrows (CH1 and CH2 buttons) to change the

MONTH.e. Use the right arrow (CH4) button to advance to the DAY position.f. Use the up and down arrows (CH1 and CH2 buttons) to change the DAY.g. When you have finished with the date, press the right arrow until the first

character of the TIME field turns yellow.h. Continue to change characters and advance through the time function

until all desired changes are entered.i. Use the right arrow (CH4) button to advance to the DATE FORM position.j. Use the up and down arrows (CH1 and CH2 buttons) to change the date

format display. NOTE: The date field does not change in the Setup Menuafter the date format is changed, but the selected date format is saved inmemory. The new format will be displayed on the screen.

k. Press RESET.

[3] Change the amount of time a. Press CH3 (3 flashes yellow and the time character in the QUAD fieldSEQUENCE that each screen is displayed turns yellow).

during the sequence mode. b. Use the up and down arrows (CH1 and CH2 buttons) to change the(Screens always rotate in the time. Time range is OFF, 1 to 30 seconds.order of QUAD, CH1, CH2, c. Use the left and right arrows (CH3 and CH4 buttons) to advance to theCH3, CH4.) next or return to the previous channel position.

d. Continue to change channels and advance through the times functionsuntil all desired changes are entered.

e. Press RESET.

[4] Change the PIP Format a. Press CH4 (4 flashes yellow) (The format character in the PIP FORMATMISC (horizontal or vertical), Auto field turns yellow)

Reset time (off, 1 to 60 c. Use the left and right arrows (CH3 and CH4 buttons) to advance to theseconds, Alarm Beep (on or next or return to the previous field.off alarm SensorType d. Continue to change fields and advance through the settings until all(normally open or normally desired changes are entered.closed and Active Out (TTL high e. Press RESET.to alarm or TTL low to alarm).

EXIT Return to normal display mode. Press ALT + MENU


CHECK OUT

Table B. Check-Out Procedure

This procedure assumes that power is on.

Step Procedure Results

1 Calibrate cameras. Follow the manufacturer’s recommendations for calibration.

2 Press the QUAD/MENU button. See quad display.

3 Press the CH 1 button. See channel 1 image full screen.




7 Press the PIP/SEQ button. See PIP display.

8 While holding the RESET/ALT button, See each channel image displayed full screen in sequence.press the PIP/SEQ button.

9 Press any channel button, then press the Zoom area is highlighted in the center of the screen.ZOOM/FREEZE button.Use arrow keys to move the highlighted area. The highlighted area moves to different parts of the screen.Press the QUAD/MENU button. The image zooms to show the selected area full screen.Press the RESET/ALT button. See the selected channel image full screen (normal).

10 Put an object in the area being observed by See the object on the screen. Any movement will be seen.the selected camera.While holding the RESET/ALT button, press See the object frozen on the screen. No movement will bethe ZOOM/FREEZE button. seen.Remove the object from the observed area. The object remains on the screen.Press the RESET/ALT button. The object disappears and movement is once again seen.

11 Check-out is complete.

OPERATION

The buttons below the screen control the programming and control functions.

DISPLAY

The monitor display can show all cameras in a quad display, show all cameras with oneprominent (picture-in-picture), show only one camera, sequence between all cameras,zoom, and freeze (refer to Figure 5).

Table C. Display Functions

Function To Activate Press To Deactivate Press

Show all cameras (quad). QUAD PIP, CH1, CH2, CH3, or CH4

Show picture-in-picture (PIP). PIP. Each time you press PIP, the QUAD, CH1, CH2, CH3, or CH4prominent camera is stepped throughCH1, CH2, CH3, CH4.

Show one camera. CH1, CH2, CH3, or CH4. PIP, QUAD, or another camera

Sequence all cameras. ALT + SEQ. QUAD, PIP, CH1, CH2, CH3, or CH4.

Zoom (works only in single- ZOOM. Use arrow keys (CH1, CH2, ZOOMcamera mode). CH3, CH4) to locate zoom area where

you want it. Then press QUAD to expandthe view. The arrow keys will still functionto move the image area.

Freeze (works in any mode ALT + FREEZE ALT + FREEZEbut zoom). In QUAD and PIP modes next press the

desired camera channel. You can pressmore than one channel.


Figure 5. Display Selections

PIP MODE (HORZ)

QUAD MODE

SEQUENCE MODE

PIPSEQ

QUADMENU

SINGLE-CAMERA MODECH4VCR

MENU MODE

CH4VCR

CH3

ZOOMFREEZE

CH2CH1 TALKAUDIO

MIC


PIPSEQ

QUADMENU

RESETALT

PIPSEQ

RESETALT

QUADMENU

RESETALT

CH1 CH2 CH3


INTERCOM

The intercom operates with one camera at a time. When the monitor is in quad displaymode, a speaker icon appears next to the channel number to show which camera has theintercom active.

NOTE: The intercomfunction is available onlywhen CCQ1400A-4cameras are used.

Figure 6. Intercom Activities on Screen

SPEAKER SYMBOL SHOWS WHICHCHANNEL IS IN INTERCOM MODE.

RESETALT

TALKAUDIO

PRESS ALT + AUDIO TO CHANGEINTERCOM CHANNEL.

Table D. Intercom Function

IntercomFunction Action

Listen channel X In quad mode, hold the ALT/RESET buttonand repeatedly press and release the AUDIO/TALK button until the speaker icon appears inthe window of the desired channel.

Talk channel X Perform listen step described above.Release the ALT/RESET button and pressand hold the AUDIO/TALK button.Speak in a normal voice.Release button to hear response.Adjust volume control, if necessary.

NOTE: You can operate the intercom when the other displaymodes are active (single channel and PIP), but you cannot changethe channel unless you are in Quad mode.


ALARM

The alarm operates with any or all cameras at once. ALM flashes at the top center of thescreen and the display automatically switches to show the camera that has the alarm.

Figure 7. Alarm Activities on Screen

Table E. Alarm Function

Alarm Function Action

Alarm occurs at a camera location. The display switches to show a full-screen display of the camera that has thealarm and ALM flashes at the top center of the display. If alarm beep is programmed ON, the beep sounds for the programmed time period.

Manually acknowledge the alarm. Press the RESET button. The display returns to the mode it was in before thealarm happened. The alarm beep stops. If the alarm condition still exists, ALMappears at the top of the screen.

Alarm is automatically reset If the programmed reset time has passed, the display returns to the mode it was(if the alarm has not been manually in before the alarm happened. The alarm beep stops. If the alarm condition stillacknowledged). exists, ALM appears at the top of the screen.

The condition that caused the alarm Display switches as described above when an alarm occurs at a camera location.returns to normal.

Manually acknowledge the return Press the RESET button. The display returns to the mode it was in before theto normal. alarm returned to normal. The alarm beep stops. ALM disappears from the top of

the screen.

Return to normal is automatically If the programmed reset time has passed, the display returns to the mode it wasreset (if the alarm has not been in before the alarm returned to normal. The alarm beep stops. ALM disappearsmanually acknowledged). from the top of the screen.

VCR RECORD/PLAYBACK

If a VCR is connected at the Video and Audio jacks (refer to Figure 3), the image displayedon the screen can be recorded. To enter the playback mode, hold the ALT button while youpress the VCR button; the screen displays VCR playback. Press Reset to return to thenormal display mode.

RESETALT

ALARM CAUSES THE ALARMEDCHANNEL TO SHOW FULL SCREEN,ALM BLINKS, BEEP SOUNDS (IF ON).

PRESS RESET TO ACKNOWLEDGEALARM & STOP BEEP. DISPLAY RETURNSTO THE ORIGINAL MODE. WHEN THEALARM GOES AWAY, THE CYCLE STARTSOVER.


Figure 8. Monitor Back Panel Controls and Connections

Table F. Back Panel Reference Key

ReferenceNumber Description Function

1 Power inlet Accepts 110 to 240 Volts AC, 50/60 Hz power.

2 Main power switch Controls power to monitor and cameras.

3 75-ohm/High impedance switch Camera inputs: Set to 75 ohms unless looping outputsare used.Monitor output: Set to 75 ohms if output is unused. Setto HI if equipment is connected.

4-7 Video/Audio inputs (6-pin mini-DIN) Input for CCQ1400A-4 cameras.

8-11 Video looping output/Video input Connect additional monitor or VCR to the channel, or(BNC) connect a camera that uses BNC connector.

12 Monitor output Connect VCR or additional monitor to the quad circuit.

13 Alarm input/output connector CH1, CH2, CH3, CH4: Connect alarm detection(10-position, snap-in type) contacts (works the same as the alarm inputs on the

camera) or alarm output to annunciators or otherdevices. Output switches from 5 VDC to ground onalarm with N.O. alarm contacts. Output switches fromground to 5 VDC on alarm with N.C. contacts.TRIG OUT: Connect a trigger input to start a VCR whenan alarm is detected. Trig Out switches from ground to 5VDC on alarm when Active Out (on the menu) is set forL. Trig Out switches from 5 VDC to ground on alarmwhen Active Out is set for H.

14 Remote control serial port (DB9) This is normally not used. Contact Pelco for pin-out andcoding.

15 VCR input/outputs (phono jacks) Interface video and audio signals to and from a VCR.

MAIN

A/C INLET

CH 1

IN

IN/OUT

CH 3 CH 4CH 2

IN

OUT

MONITOROUT

VIDEO AUDIO

75 Hi 75 Hi 75 Hi 75 Hi 75 Hi

SCREEN

FOCUS

2 3

1

13 14

4 5 6 7

8 9 10 11

CH 1 CH 2 CH 3 CH 4 TRIGOUT

12

REMOTE*

15


Figure 9. Monitor Controls

Table G. Front Panel Reference Key

ReferenceNumber Description Function

1 Reset/ALT key Resets alarm or video loss detection. When there is no alarm, use as ALT key toactivate the alternate functions of the Zoom, PIP, Quad, CH4, and Talk keys.

2 Zoom/Freeze key Toggles zoom mode when viewing single camera. In single-camera mode,freezes display when pressed while the ALT key is held in. In multiple-cameramodes, freezes selected display when pressed while the ALT key is held inand then a channel key is pressed.

3 PIP/Sequence key In display mode, shows picture-in picture view. Continuous pressing rotates the full-screen view. If pressed while the ALT key is held in, starts sequential viewing mode.

4 Quad/Menu key In display mode, shows quad view. If pressed while the ALT key is held in,enters menu/setup mode.

5 Power Indicator LED Illuminates when monitor power is on.

6 CH1/UP key In display mode, shows full view of channel 1. In menu mode, moves cursor upor toggles setting.

7 CH2/Down key In display mode, shows full view of channel 2. In menu mode, moves cursordown or toggles setting.

8 CH3/Left key In display mode, shows full view of channel 3. In menu mode, moves cursor leftor toggles setting.

9 CH4/Right key/VCR In display mode, shows full view of channel 4. In menu mode, moves cursor rightor toggles setting. If pressed while the ALT key is held in, display switches to theVCR playback mode.

10 Talk/Audio Press to talk switch to activate microphone. Press and hold to talk. Release tolisten. If pressed while the ALT key is held in, moves audio connection to thenext channel.

11 Microphone Speak in microphone to talk to people at camera locations.

12 Tint Adjusts display color phase/flesh tones.

13 Sharpness Adjusts display sharpness level.

14 Color Adjusts display color saturation level.

15 Brightness Adjusts display brightness.

16 Contrast Adjusts display contrast.

17 Volume Adjusts loudness of the speaker (effective only when cameras are equipped withthe audio option or when playing back recorded sound from a VCR).

18 Power button Controls power to monitor only. Power to the cameras and quad circuitry iscontrolled only with the switch on the back of the monitor.

CH4VCR

CH3

ZOOMFREEZE

CH2CH1 MIC


PIPSEQ

QUADMENU

RESETALT

TALKAUDIO

1 2 3 4 5

6 7 8 9 10 11 12 13 14 15 16 17 18


TECHNICAL SPECIFICATIONS

ELECTRICAL

Input Voltage: 100 to 240 VAC, 50/60 HzPower Consumption: 70 wattsSignal Format: NTSCScanning System: 2:1 interlacePicture Elements: 512 (H) x 492 (V)Horizontal Resolution: 350 TV lines (center)Linearity: Less than 12%Audio Output: 1.1 W +/-0.2 W at 8-ohm resistive loadPixel Format

Single Screen: 720 (H) x 480 (V)Quad Screen: 360 (H) x 240 (V)PIP Screen: 208 (H) x 136 (V)

Refresh Rate: 30 frames per second (NTSC)Digital Zoom: 2XOSD Character: 16 x 20 bit map font (upper case alpha characters, numbers, and

symbols)Video SwitchingTime When MultipleAlarms Occur: 1 secondMaximum CharacterDisplay Format: 45 (H) x 24 (V) (1,080 characters)

GENERAL

Picture Tube: 14-inch diagonal colorControls: Sharpness, color, brightness, contrast, tint, and volumeCharacter Display: 8 alphanumeric characters each for camera, date, time, alarm,

video loss, and freeze for each channelDisplay Modes: One camera, four cameras (quad), picture-in-picture (PIP), and

VCRSequentialSwitching Mode: Set dwell time from 1 to 30 seconds; OFF setting skips channelVideo LossDetection: All channelsTime Mode: 12-hour mode with AM/PM indicatorAlarm Inputs: 4, activated by N.O. or N.C. contact

closure (programmable)Alarm Output: 1, common to all 4 inputs, TTL compatible (programmable for high

or low output)Alarm Beep: On or off (programmable)AutomaticAlarm Reset: Set reset time from 1 to 60 seconds; OFF setting defeats auto

reset (programmable)Video/AudioInput Connectors: 4X6P mini-DINVideo InputConnectors: 4 BNCVideo LoopingConnectors: 4 BNCMonitor OutputConnector: 1 BNCVCR Input/OutputConnectors: 4 RCA (2 video and 2 audio)Remote PortConnector: DB9 maleAlarm Connector: 10-position, snap-in type (push-in wireImpedanceTermination: 75 ohms or bridging for 4 video inputs (from cameras) and 1

monitor outputDimensions: 13.68 (W) x 12.75 (H) x 14.68 (D) inches

(34.75 x 32.38 x 37.29 cm)Weight: 28.6 lb (13 kg)


ENVIRONMENTAL

OperatingTemperature: 32° to 104°F (0° to 40°C)StorageTemperature: 4° to 158°F (-20° to 70°C)Humidity: 35% to 80%, non-condensing

(Design and product specifications subject to change without notice.)

REGULATORY NOTICES

Note: This equipment has been tested and found to comply with the limits of a Class Adigital device, pursuant to part 15 of the FCC rules. These limits are designed to providereasonable protection against harmful interference when the equipment is operated in acommercial environment. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instruction manual, may causeharmful interference to radio communications. Operation of this equipment in a residentialarea is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense.


REVISION HISTORYManual # Date CommentsC1970M 7/00 Original version.C1970M-A 7/01 Date and time programming revised.

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2001, Pelco.Endura and ExSite are trademarks of Pelco. All rights reserved.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Seriesfixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used incontinuous motion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network videorecorders, and Endura™ Series distributed network-based video products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will becovered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motionapplications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelcoshipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,California. Repairs made necessary by reason of misuse, alteration, normal wear, or accidentare not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting fromthe specific use or application made of the Products. Pelco’s liability for any claim, whetherbased on breach of contract, negligence, infringement of any rights of any party or productliability, relating to the Products shall not exceed the price paid by the Dealer to Pelco forsuch Products. In no event will Pelco be liable for any special, incidental or consequentialdamages (including loss of use, loss of profit and claims of third parties) however caused,whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also haveadditional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the followinginformation:1. Model and serial number2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under thewarranty conditions stated above, please include a written explanation with the productwhen returned.

Method of return shipment shall be the same or equal to the method by which the item wasreceived by Pelco.

RETURNSIn order to expedite parts returned to the factory for repair or credit, please call the factory at(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returnedfor credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishingcharge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RAnumber and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:Service DepartmentPelco3500 Pelco WayClovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and areinstructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:Pelco3500 Pelco WayClovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:Pelco c/o Expeditors473 Eccles AvenueSouth San Francisco, CA 94080 USAPhone: 650-737-1700Fax: 650-737-0933

Pelco PMCQ14A 14-Inch Color Quad Monitor Manual

Documents

Transcript of Pelco PMCQ14A 14-Inch Color Quad Monitor Manual