PD3068: Package Mechanical Drawings Datasheet
Transcript of PD3068: Package Mechanical Drawings Datasheet
PD3068 DatasheetPackage Mechanical Drawings
5193068. 62.0 7/19
Microsemi HeadquartersOne Enterprise, Aliso Viejo,CA 92656 USAWithin the USA: +1 (800) 713-4113 Outside the USA: +1 (949) 380-6100Sales: +1 (949) 380-6136Fax: +1 (949) 215-4996Email: [email protected]
©2019 Microsemi, a wholly owned subsidiary of Microchip Technology Inc. All rights reserved. Microsemi and the Microsemi logo are registered trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners.
Microsemi makes no warranty, representation, or guarantee regarding the information contained herein or the suitability of its products and services for any particular purpose, nor does Microsemi assume any liability whatsoever arising out of the application or use of any product or circuit. The products sold hereunder and any other products sold by Microsemi have been subject to limited testing and should not be used in conjunction with mission-critical equipment or applications. Any performance specifications are believed to be reliable but are not verified, and Buyer must conduct and complete all performance and other testing of the products, alone and together with, or installed in, any end-products. Buyer shall not rely on any data and performance specifications or parameters provided by Microsemi. It is the Buyer’s responsibility to independently determine suitability of any products and to test and verify the same. The information provided by Microsemi hereunder is provided “as is, where is” and with all faults, and the entire risk associated with such information is entirely with the Buyer. Microsemi does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other IP rights, whether with regard to such information itself or anything described by such information. Information provided in this document is proprietary to Microsemi, and Microsemi reserves the right to make any changes to the information in this document or to any products and services at any time without notice.
About MicrosemiMicrosemi, a wholly owned subsidiary of Microchip Technology Inc. (Nasdaq: MCHP), offers a comprehensive portfolio of semiconductor and system solutions for aerospace & defense, communications, data center and industrial markets. Products include high-performance and radiation-hardened analog mixed-signal integrated circuits, FPGAs, SoCs and ASICs; power management products; timing and synchronization devices and precise time solutions, setting the world's standard for time; voice processing devices; RF solutions; discrete components; enterprise storage and communication solutions, security technologies and scalable anti-tamper products; Ethernet solutions; Power-over-Ethernet ICs and midspans; as well as custom design capabilities and services. Learn more at www.microsemi.com.
Contents
1 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Revision 62.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 Revision 61.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3 Revision 60.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4 Revision 59.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5 Revision 58.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.6 Revision 57.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.7 Revision 56.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.8 Revision 55.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.9 Revision 54.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.10 Revision 53.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.11 Revision 52.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.12 Revision 51.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.13 Revision 50.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.14 Revision 49.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.15 Revision 48.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.16 Revision 47.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.17 Revision 46.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.18 Revision 45.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.19 Revision 44.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.20 Revision 43.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.21 Revision 42.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.22 Revsion 41.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.23 Revsion 40.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.24 Revision 39.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.25 Revsion v11.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.26 Revision v11.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.27 Revision v11.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.28 Revision v11.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.29 Revision v11.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.30 Revision v10.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.31 Revision v10.8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.32 Revision v10.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.33 Revision v10.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.34 Revision v10.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.35 Revision v10.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.36 Revision v10.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.37 Revision v10.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.38 Revision v10.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.39 Revision v10.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.40 Revision v9.9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.41 Revision v9.8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Package Mechanical Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72.1 Naming Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72.2 CPGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5193068 PD3068 Datasheet Revision 62.0 I
2.2.1 PG84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72.2.2 PG100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82.2.3 PG132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92.2.4 PG175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102.2.5 PG176 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112.2.6 PG207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.2.7 PG257 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.3 Ceramic Quad Flat Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142.3.1 CQ84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142.3.2 CQ84 Side View and Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.3.3 CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352—Cavity Up without Heat Sink . . . . . . 172.3.4 CQ208 and CQ256—Cavity Up with Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.3.5 CQ256—Cavity Down without Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232.3.6 CQ256—Cavity Down with Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252.3.7 CQFP without Heat Sink Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262.3.8 CQFP with Heat Sink Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.4 CCLG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.4.1 CC256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.4.2 CCLG Substrate Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292.4.3 LG1657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.5 CCGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312.5.1 CG484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312.5.2 CG624 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322.5.3 CG896 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322.5.4 CCGA Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332.5.5 CG1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342.5.6 CG1272 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352.5.7 CG1657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.6 PLCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372.6.1 Plastic Leaded Chip Carrier Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.7 QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382.7.1 QN48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382.7.2 QN68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392.7.3 QN48 and QN68 Quad Flat No Leads Single Row Dimension . . . . . . . . . . . . . . . . . . . . . . . . 40
2.8 Quad Flat No Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412.8.1 Quad Flat No Lead Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422.8.2 QN108 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432.8.3 QN132 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442.8.4 QN180 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452.8.5 Quad Flat No Leads Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
2.9 Plastic Quad Flat Pack Rectangular Package (TQ144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472.10 Plastic Quad Flat Pack (PQFP, TQFP, VQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482.11 Plastic Quad Flat Pack—Exposed Heatsink (RQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492.12 Plastic Quad Flat Pack Rectangular Package (PQ100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
2.12.1 PQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522.12.2 Plastic Quad Flat Pack (RQFP/PQFP) Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532.12.3 TQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542.12.4 VQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
2.13 PBGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552.13.1 BG272 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552.13.2 BG313 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562.13.3 BG329 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572.13.4 BG456 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582.13.5 BG729 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592.13.6 PBGA Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
2.14 FBGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5193068 PD3068 Datasheet Revision 62.0 II
2.14.1 FG144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 612.14.2 FG256 MO-192 VAR DAF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 622.14.3 FG256 MS-034 VAR AAF-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632.14.4 FG324 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642.14.5 FG484 MS-034 VAR AAL-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652.14.6 FG484—Fully Populated MS-034 VAR AAJ-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662.14.7 FG676 (Option 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 672.14.8 FG676 (Option 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682.14.9 FG676 (Option 1 and 2) Package Mechanical Drawing Dimensions . . . . . . . . . . . . . . . . . . . . 692.14.10 FG484—Fully Populated MS-034 VAR AAJ-1, Larger Mold Cap Size . . . . . . . . . . . . . . . . . . 702.14.11 FG896 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712.14.12 FG896—Larger Mold Cap Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712.14.13 FG1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 722.14.14 Fine Pitch Plastic Ball Grid Array Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732.14.15 FC1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 752.14.16 FCV484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 762.14.17 FCV484 Package Mechanical Drawing Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 772.14.18 FC1152 Package Mechanical Drawing Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
2.15 Chip Scale Package (UC/CS/VF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 782.15.1 UC36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 792.15.2 CS49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 792.15.3 UC81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 802.15.4 CS81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 812.15.5 CS121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 822.15.6 CS128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832.15.7 CS180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 842.15.8 CS196 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 852.15.9 CS201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 862.15.10 FCS325–(Option 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872.15.11 FCS325–(Option 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 882.15.12 CS281 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 892.15.13 CS288 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902.15.14 FCS536 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 912.15.15 CS289 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 922.15.16 Chip Scale Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932.15.17 VF256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
2.16 Very Fine Pitch Ball Grid Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 962.16.1 VF400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 962.16.2 Dimensions of VF400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972.16.3 Dimensions of VF256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5193068 PD3068 Datasheet Revision 62.0 III
Figures
Figure 1 Package Outline of PG84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Figure 2 Package Outline of PG100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Figure 3 Package Outline of PG132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Figure 4 Package Outline of PG175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Figure 5 Package Outline of PG176 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Figure 6 Package Outline of PG207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Figure 7 Package Outline of PG257 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Figure 8 Package Top View of CQ84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Figure 9 Bottom and Side Views of CQ84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Figure 10 CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352—Cavity Up without Heat Sink . . . . . . . . . 18Figure 11 RTG4 CQ352—Cavity Up without Heat Sink: Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Figure 12 RTG4 CQ352—Cavity Up without Heat Sink: Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Figure 13 CQ208 and CQ256—Cavity Up with Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Figure 14 CQ256—Cavity Down without Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Figure 15 CQ256—Cavity Down with Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Figure 16 Package Outline of CC256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Figure 17 CCLG Substrate Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Figure 18 Package Outline of LG1657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Figure 19 Package Outline of CG484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Figure 20 Package Outline of CG624 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Figure 21 Package Outline of CG896 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Figure 22 Package Outline of CG1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Figure 23 Package Outline of CG1272 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Figure 24 Package Outline of CG1657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Figure 25 PLCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Figure 26 Package Outline of QN48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Figure 27 Package Outline of QN68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Figure 28 Quad Flat No Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Figure 29 Quad Flat No Lead Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Figure 30 Bottom View of QN108 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Figure 31 Bottom View of QN132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Figure 32 Bottom View of QN180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Figure 33 Plastic Quad Flat Pack Rectangular Package (TQ144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Figure 34 Plastic Quad Flat Pack (PQFP, TQFP, VQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Figure 35 Plastic Quad Flat Pack—Exposed Heatsink (RQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Figure 36 Plastic Quad Flat Pack Rectangular Package (PQ100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Figure 37 Package Outline of BG272 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Figure 38 Package Outline of BG313 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Figure 39 Package Outline of BG329 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Figure 40 Package Outline of BG456 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Figure 41 Package Outline of BG729 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Figure 42 Package Outline of FG144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Figure 43 Package Outline of FG256 MO-192 VAR DAF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Figure 44 Package Outline of FG256 MS-034 VAR AAF-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Figure 45 Package Outline of FG324 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Figure 46 Package Outline of FG484 MS-034 VAR AAL-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Figure 47 Package Outline of FG484—Fully Populated MS-034 VAR AAJ-1 . . . . . . . . . . . . . . . . . . . . . . . . 67Figure 48 Package Outline of FG676 (Option 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Figure 49 Package Outline of FG676 (Option 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Figure 50 Package Outline of FG484 MS-034 VAR AAJ-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Figure 51 Package Outline of FG896 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Figure 52 Package Outline of FG896 Larger Mold Cap Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Figure 53 Package Outline of FG1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Figure 54 Package Outline of FC1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
5193068 PD3068 Datasheet Revision 62.0 IV
Figure 55 Package Outline of FCV484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Figure 56 Package Outline of UC36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Figure 57 Package Outline of CS49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Figure 58 Package Outline of UC81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Figure 59 Package Outline of CS81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Figure 60 Package Outline of CS121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Figure 61 Package Outline of CS128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Figure 62 Package Outline of CS180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Figure 63 Package Outline of CS195 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Figure 64 Package Outline of CS201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Figure 65 Package Outline of FCS325 (Option 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Figure 66 Package Outline of FCS325–(Option 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Figure 67 Package Outline of CS281 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Figure 68 Package Outline of CS288 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Figure 69 Package Outline of FCS536 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Figure 70 Package Outline of CS289 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Figure 71 Package Outline of VF256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Figure 72 Package Outline of VF400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
5193068 PD3068 Datasheet Revision 62.0 V
Tables
Table 1 Package Naming Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Table 2 Supported Devices for PG84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Table 3 Supported Devices for PG100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Table 4 Supported Devices for PG132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Table 5 Supported Devices for PG175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Table 6 Supported Devices for PG175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Table 7 Supported Devices for PG207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Table 8 Supported Devices for PG257 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Table 9 Supported Devices for CQ84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Table 10 Plate Thickness for CQ84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Table 11 Lid Size for CQ84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Table 12 Supported Devices for CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352 . . . . . . . . . . . . . . . 21Table 13 Supported Devices for CQ208 and CQ256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Table 14 Supported Devices for CQ256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Table 15 Supported Devices for CQ256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Table 16 Dimensions for CQFP without Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Table 17 Dimensions for CQFP with Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 18 Supported Devices for CC256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Table 19 Supported Devices for LG1657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Table 20 Supported Devices for CG484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Table 21 Supported Devices for CG624 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Table 22 Supported Devices for CG896 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Table 23 Dimensions of CCGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Table 24 Supported Devices for CG1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Table 25 Supported Devices for CG1272 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Table 26 Supported Devices for CG1657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Table 27 Supported Devices for PL44, PL68, and PL84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Table 28 Dimensions of Plastic Leaded Chip Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Table 29 Supported Devices for QN48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Table 30 Supported Devices for QN68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Table 31 QN48 and QN68 Quad Flat No Leads Single Row Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Table 32 Supported Devices for QN108 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Table 33 Supported Devices for QN132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Table 34 Supported Devices for QN180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Table 35 Dimensions of Quad Flat No Leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Table 36 Dimensions for QN108, QN132, and QN180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Table 37 Supported Devices for Plastic Quad Flat Pack Rectangular Package . . . . . . . . . . . . . . . . . . . . . . 52Table 38 PQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Table 39 RQFP/PQFP) Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Table 40 Supported Devices for Quad Slat (TQ/VQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Table 41 TQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Table 42 VQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Table 43 Supported Devices for BG272 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Table 44 Supported Devices for BG313 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Table 45 Supported Devices for BG329 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Table 46 Supported Devices for BG456 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Table 47 Supported Devices for BG729 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Table 48 PBGA Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Table 49 Supported Devices for FG144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Table 50 Supported Devices for FG256 MO-192 VAR DAF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Table 51 Supported Devices for FG256 MS-034 VAR AAF-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Table 52 Supported Devices for FG324 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Table 53 Supported Devices for FG484 MS-034 VAR AAL-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Table 54 Supported Devices for FG484—Fully Populated MS-034 VAR AAJ-1 . . . . . . . . . . . . . . . . . . . . . . 67
5193068 PD3068 Datasheet Revision 62.0 VI
Table 55 Supported Devices for FG676 (Option 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Table 56 Supported Devices for FG676 (Option 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Table 57 Dimensions of FG676 (Option 1 and 2) Package Mechanical Drawing . . . . . . . . . . . . . . . . . . . . . 69Table 58 Supported Devices for FG484 MS-034 VAR AAJ-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Table 59 Supported Devices for FG896 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Table 60 Supported Devices for FG896 Larger Mold Cap Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Table 61 Supported Devices for FG1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Table 62 Fine Pitch Plastic Ball Grid Array Dimensions for FG144, FG256, and FG324 . . . . . . . . . . . . . . . 73Table 63 Fine Pitch Plastic Ball Grid Array Dimensions for FG484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Table 64 Fine Pitch Plastic Ball Grid Array Dimensions for FG896 and FG1152 . . . . . . . . . . . . . . . . . . . . . 75Table 65 Supported Devices for FC1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Table 66 Supported Devices for FCV484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Table 67 FCV484 Package Mechanical Drawing Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Table 68 Dimensions of FC1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Table 69 Supported Devices for UC36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Table 70 Supported Devices for CS49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Table 71 Supported Devices for UC81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Table 72 Supported Devices for CS81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Table 73 Supported Devices for CS121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Table 74 Supported Devices for CS128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Table 75 Supported Devices for CS180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Table 76 Supported Devices for CS196 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Table 77 Supported Devices for CS201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Table 78 Supported Devices for FCS325 (Option 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Table 79 Supported Devices for FCS325 (Option 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Table 80 Supported Devices for CS281 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Table 81 Supported Devices for CS288 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Table 82 Supported Devices for FCS536 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Table 83 Supported Devices for CS289 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Table 84 Chip Scale Package Dimensions for UC36, CS49, UC81, and CS81 . . . . . . . . . . . . . . . . . . . . . . 93Table 85 Chip Scale Package Dimensions for CS121, CS128, CS180, CS196, and CS201 . . . . . . . . . . . . 94Table 86 Chip Scale Package Dimensions for FC325 and FC536 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Table 87 Chip Scale Package Dimensions for FC325 and FC536 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Table 88 Supported Devices for VF256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Table 89 Supported Devices for VS400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Table 90 Dimensions of VF400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Table 91 Dimensions of VF256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5193068 PD3068 Datasheet Revision 62.0 VII
Revision History
1 Revision History
The revision history describes the changes that were implemented in the document. The changes are listed by revision, starting with the most current publication.
1.1 Revision 62.0Updated the LG1657, page 29 bottom view diagram (SAR 78574).
1.2 Revision 61.0The following is a summary of the changes in revision 61.0 of this document.
• Updated CG1657, page 36 by removing C1 pin (SAR 94666).• Updated Figure 54, page 76 image (SAR 94196).• Added RTG4 CQ352 package outline in the CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352—
Cavity Up without Heat Sink section. For more information, see Figure 11, page 19.
1.3 Revision 60.0The following is a summary of the changes in revision 60.0 of this document.
• Updated CG1657, page 36 by removing C1 pin (SAR 78574).• Updated FG896, page 71 image (SAR 49423).• Updated Fine Pitch Plastic Ball Grid Array Dimensions, page 73 table for D2 and E2 options (SAR
49423).• Updated Fine Pitch Plastic Ball Grid Array Dimensions, page 73 table for in correct decimal values
for A1 FG484 (SAR 51031).• Removed Note in Fine Pitch Plastic Ball Grid Array Dimensions, page 73 (SAR 58283).• Updated CS325 to FCS325 and CS536 to FCS536 throughout the document (SAR 62909).• Added CQ352 MO-134 VAR AE in CQFP without Heat Sink Dimensions, page 26 (SAR 82812).• Added note for CQFP without Heat Sink Dimensions, page 26 (SAR 82812).
1.4 Revision 59.0Updated the FG676 (Option 2), page 68 bottom view diagram for the corner pin balls (SAR 76003).
1.5 Revision 58.0Updated the M2S060 and M2GL060 device details in the FG676 (Option 2), page 68, FG484—Fully Populated MS-034 VAR AAJ-1, Larger Mold Cap Size, page 70, FCS325–(Option 1), page 87, and VF400, page 96 (SAR 69566).
1.6 Revision 57.0The following is a summary of the changes in revision 57.0 of this document.
• Updated VF256, page 95 mechanical drawing (SAR 66875).• Updated Dimensions of VF400, page 97 (SAR 66875).• Updated FG484—Fully Populated MS-034 VAR AAJ-1, Larger Mold Cap Size, page 70 Package
Mechanical Drawing Dimensions (SAR 64737).• Removed RTAX4000D from CG1272, page 35 support devices (SAR 66765). • Added CG1657, page 36 package and LG1657, page 29 (SAR 66765).
1.7 Revision 56.0Updated FG676 (Option 2), page 68 mechanical drawing (SAR 62340).
5193068 PD3068 Datasheet Revision 62.0 1
Revision History
1.8 Revision 55.0Added the mechanical drawing of the Plastic Quad Flat Pack Rectangular Package (TQ144), page 47 package. Removed the mechanical drawing of the VQ144 package and VQ144 Package Mechanical Drawing Dimensions. (SAR 61533).
1.9 Revision 54.0Added the mechanical drawing of the FCV484, page 76 package and FCV484 Package Mechanical Drawing Dimensions, page 77 (SAR 54037).
1.10 Revision 53.0Added the mechanical drawing of the FCS536, page 91 package and "FCS536" Package Mechanical Drawing Dimensions (SAR 60514).
1.11 Revision 52.0Updated the mechanical drawing of the FCS325–(Option 2), page 88 package and FCS325 (Option 2) Package Mechanical Drawing Dimensions (SAR 58504).
1.12 Revision 51.0Corrected the reference device support for "VQ144" (SAR 58334).
1.13 Revision 50.0Corrected the pitch (e) on the VQ144 from 0.05 BSC to 0.50 BSC in "Plastic Quad Flat Pack Rectangular Package (VQ144) Dimensions" section (SAR 57666).
1.14 Revision 49.0The following is a summary of the changes in revision 49.0 of this document.
• Updated Note 2 and Note 3 for CG1152, page 34 package outline drawing (SAR 55805).• Updated Note 2 and Note 3 for CCGA, page 31 package outline drawing (SAR 55805).• Added note QN180 Bottom View, page 45, "QN132 Bottom View" and "QN180 Bottom View"
packages in the document (SAR 56846).• Added "Plastic Quad Flat Pack Rectangular Package (VQ144)" package outline drawings and
supported devices.Added "Plastic Quad Flat Pack Rectangular Package (VQ144) Dimensions" (SAR 53464).
• Renamed FG676 (Option 1), page 67 and FG676 (Option 2), page 68 (SAR 54063).• Updated FG676 (Option 2), page 68 package outline drawing (SAR 55191).• Updated the mechanical drawing of the FCS325–(Option 1), page 87 package and "FCS325 (Option
1)" Package Mechanical Drawing Dimensions (SAR 53464).• Added Chip Scale Package Dimensions, page 93 package outline drawing and added "FCS325
(Option 2)" Package Mechanical Drawing Dimensions (SAR 53464).• Added VF256, page 95 package outline drawing and also added Dimensions of VF400, page 97
(SAR 53464).
1.15 Revision 48.0Updated the mechanical drawing of FG896—Larger Mold Cap Size, page 71 package (SAR 49607).
1.16 Revision 47.0Added FG676 (Option 2), page 68, FC1152, page 75, and FCS325–(Option 1), page 87 package outline drawings and supported devices (SAR 51485).
1.17 Revision 46.0Updated the mechanical 3awing of the VF400, page 96 package (SAR 49374).
5193068 PD3068 Datasheet Revision 62.0 2
Revision History
1.18 Revision 45.0Updated the Supported Devices details for FG484—Fully Populated MS-034 VAR AAJ-1, page 66, FG896—Larger Mold Cap Size, page 71, and VF400, page 96 (SAR 48235).
1.19 Revision 44.0The following is a summary of the changes in revision 44.0 of this document.
• Table 1, page 7 was updated to include the VFPBA package.• The cross-reference to the CQFP with Heat Sink Dimensions, page 27 dimensions table was
corrected in the table notes for the CQ208 and CQ256—Cavity Up with Heat Sink, page 21 section (SAR 44419).
• AGL250 was added as a supported device in the CS81, page 81 section (SAVF256_Package_Outline_Drawing R 43697).
• The VF400, page 96 is new (47028).
1.20 Revision 43.0The following is a summary of the changes in revision 43.0 of this document.
• A2F060 was added as a supported device for "TQ144" (SAR 43622).• The FG484—Fully Populated MS-034 VAR AAJ-1, page 66 and FG896—Larger Mold Cap Size,
page 71 section are new. These packages are new for the SmartFusion2 family and differ from the existing FG484 and FG896 packages due to a larger mold cap and the pin gate feature, which prevents marking in the center of the package (SAR 42898).
1.21 Revision 42.0Added new note in Fine Pitch Plastic Ball Grid Array Dimensions, page 73 (SAR 35957).
1.22 Revsion 41.0Removed “RTSX72SU” from "CQ208" and "CQ256" columns in Table 12, page 21 (SAR 32881).
1.23 Revsion 40.0The following is a summary of the changes in revision 40.0 of this document.
• Table 1, page 7 was added. References to packages throughout the document were changed in conformance with the conventions (SAR 27395).
• The supported devices listings for the following packages were updated and corrected (SAR 27395):• PG100, page 8 – Obsolete for 1415A• PG175, page 10 – Obsolete for A1440A• CQ84, page 14 – Obsolete for A32100DX • CQ208 and CQ256—Cavity Up with Heat Sink, page 21 – Supported for AX250 and AX500
(SAR 26344)• CQ208 and CQ256—Cavity Up with Heat Sink, page 21 – Supported for AX2000 (SAR 22918),
RT3PE600L, and RT3PE3000L• "CQ352" – Supported for RTAX4000S (SAR 30672), RTAX2000D, and RTAX4000D• CG624, page 32 – Supported for RTAX250S• CG1152, page 34 – Supported for RTAX2000S, not RTAX4000S• CCGA, page 31 – Supported for RTAX2000D and RTAX4000D• "PL84" – Obsolete for A3265A• "QN132" – Not supported for M1ASGL250 or M1A3P250• "PQ144" – Obsolete for A1240XL• "PQ208" – Not supported for M1A3PE600. Supported for A2F200 and A2F500 (SAR 31179)• "BG272" – Obsolete for A500K050 and A500K130• "FG256 MO-192 VAR DAF1" – Supported for M1AGL600• FG484—Fully Populated MS-034 VAR AAJ-1, page 66 – Not supported for M1A3P600 or
M1A3PE600• "CS49" – Obsolete for eX64 and eX128
5193068 PD3068 Datasheet Revision 62.0 3
Revision History
• "CS128" – Obsolete for eX64, eX128, and eX256• "CS180" – Obsolete for AX125 and eX256
• The lid size table for the CQ84, page 14 package was updated to add dimensions for RT1020 (SAR 27395).
• The CQ84 Side View and Bottom View, page 15 diagram was revised to add additional dimensions to the side view, noting the maximum distances between the lead and the top of the package (SAR 27406).
• Corrected the CG484, page 31 diagram by removing the pin in the A1 position (SAR 30549).• The CG896, page 32 package drawing was corrected to show the chamfered corner is at A1 (SAR
30227).• The CG1152, page 34 and CCGA, page 31 package drawings were revised to add the CLGA side
view (SARs 29751, 30553).• The FG896, page 71 diagram was corrected to show the D1 dimension extends from pin 1 to pin 30.
Previously the diagram showed that D1 extended from pin 1 to pin 29 (SAR 26792). • The FG1152, page 72 diagram was corrected to show the D1 dimension extends from pin 1 to pin
34. Previously the diagram showed that D1 extended from pin 1 to pin 33 (SAR 26792).• In the Fine Pitch Plastic Ball Grid Array Dimensions, page 73 table, dimension c for FG256 MO-192
VAR DAF1 was corrected to 0.4 to 0.6 mm. Previously it was 0.25 to 1.10 mm (SAR 28605).• A second FG896 package was added to the Fine Pitch Plastic Ball Grid Array Dimensions, page 73
table. It differs from the first FG896 package only in the D2 and E2 dimensions.• The VF289 package name was changed back to CS289, page 92 (SAR 27395).
1.24 Revision 39.0The following is a summary of the changes in revision 39.0 of this document.
• The versioning system has been changed. This document is assigned a revision number that increments each time the document is updated.
• SmartFusion devices A2F060, A2F200, and A2F500 were added to the supported devices table for the FG256 MO-192 VAR DAF1, page 62 and Fine Pitch Plastic Ball Grid Array Dimensions, page 73 (SAR 25571).
• SmartFusion devices A2F200 and A2F500 were added to the supported devices table for the FG484—Fully Populated MS-034 VAR AAJ-1, page 66 Fine Pitch Plastic Ball Grid Array Dimensions, page 73 (SAR 25571).
• The following package names were changed:• 36-Pin CSP was changed to UC36, page 79• 289-Pin CSP was changed to CS289, page 92
• The side views in the following Chip Scale Package (UC/CS/VF), page 78 drawings were corrected to show half sphere bumps instead of solder balls (SAR 26665): • UC36, page 79 • UC81, page 80• CS81, page 81
• The CS281, page 89 Chip Scale Package (UC/CS/VF), page 78 section is new (SAR 27106).• The A1 dimension values were changed to 0.07 REF in the Chip Scale Package Dimensions,
page 93 for UC36, page 79, UC81, page 80, and CS81, page 81 (SAR 26432). The c dimension values were changed to 0.21 REF. The text, “MO-195, Variation AB,” was deleted from the heading for these two packages. The b dimension values for the CS81, page 81 package were revised.
1.25 Revsion v11.4The "CCGA Dimensions" table was updated. The D1 and E1 dimensions for CG484 were changed from 22.00 to 21 (SAR 22814).
1.26 Revision v11.3Updated dimension for FBGA 144 package in the Fine Pitch Plastic Ball Grid Array Dimensions, page 73 table.
1.27 Revision v11.2A54SX16 was removed from the CQ256—Cavity Down with Heat Sink, page 25.
5193068 PD3068 Datasheet Revision 62.0 4
Revision History
1.28 Revision v11.1The following is a summary of the changes in revision v11.1 of this document.
• The ccc specification was changed from 0.10 to 0.08 in the Plastic Quad Flat Pack (RQFP/PQFP) Dimensions, page 53 table.
• The ccc specification was changed from 0.10 to 0.08 for the TQFP 167 in theTQFP Dimensions, page 54 table.
• The ccc specification was changed from 0.10 to 0.08 for the CSP 289 in theChip Scale Package Dimensions, page 93 table.
• In the Fine Pitch Plastic Ball Grid Array Dimensions, page 73 table, the following specs were updated for the FG256 MO-192 VAR DAF1, page 62:A, A1, and c.
1.29 Revision v11.0The following is a summary of the changes in revision v11.0 of this document.
• The document has been updated to include IGLOO nano packages.• The "QN48" section is new.• The UC36, page 79 section is new.
1.30 Revision v10.9The AGL400 device is new and has been added to FG144, page 61, FG256 MO-192 VAR DAF1, page 62, FG484—Fully Populated MS-034 VAR AAJ-1, page 66, and CS196, page 85.
1.31 Revision v10.8The following is a summary of the changes in revision v10.8 of this document.
• The CG484, page 31 section is new.• The CG896, page 32 is new.• Data for the 484 and 896 CCGA/LGA packages was added to the Table 23, page 33.• In the Table 35, page 46, “d” was deleted.
1.32 Revision v10.7The following is a summary of the changes in revision v10.7 of this document.
• "VQ128" and "VQ176" were added to the VQFP "Supported Devices" table.• "VQ128 MS-026 VAR AEE3" and "VQ176 MS-026 VAR BFC" dimension data are new.
1.33 Revision v10.6The following is a summary of the changes in revision v10.6 of this document.
• A3PE600L was added to the supported devices table of the FG484—Fully Populated MS-034 VAR AAJ-1, page 66 package.
• The following specifications have been updated for the FG256 MO-192 VAR DAF1, page 62:• DimensionNew Data• A1.80• A10.35 and 0.45• c0.35 and 0.60
1.34 Revision v10.5The following is a summary of the changes in revision v10.5 of this document.
• bbb has been removed from all chip scale package drawings.• The Detail A circle on the side view was added to the CS288, page 90 package drawing.• The CS289, page 92 information is new.
5193068 PD3068 Datasheet Revision 62.0 5
Revision History
1.35 Revision v10.4Note 2 under the QFN, page 38 package drawing is new and bottom view has been removed from the heading.
1.36 Revision v10.3The following is a summary of the changes in revision v10.3 of this document.
• The note under the QN108 Bottom View, page 43 package drawing is new.• The note under the QN132 Bottom View, page 44 package drawing is new. The figure was also
updated to include D1 to D4.• The note under the QN180 Bottom View, page 45 package drawing is new. The figure was also
updated to include D1 to D4.
1.37 Revision v10.2M1A3P250L was deleted; it is no longer supported.
1.38 Revision v10.1In Detail A, the A1 top arrow was incorrectly placed. It was originally at the top of the substrate and it has been moved to the bottom of the substrate in.
1.39 Revision v10.0The following is a summary of the changes in revision v10.0 of this document.
• In the CC256, page 27 figure, one of the side view dimensions was updated from 0.45±0.05 to 0.254±0.025.
• The CS201, page 86 section is new. • In the CS288, page 90 supported devices, the AGLP125 was added to the table.• In the Chip Scale Package Dimensions, page 93 table, several CS package dimensions were
updated and the CS201 information is new. Please review carefully.
1.40 Revision v9.9The Ø symbol was missing from all CCGA, PBGA, FBGA, and CSP figures. It has been added back into the document.
1.41 Revision v9.8The QFN, page 38 section, which includes the mechanical drawings and dimension measurements, is new.
5193068 PD3068 Datasheet Revision 62.0 6
Package Mechanical Drawings
2 Package Mechanical Drawings
2.1 Naming ConventionsThis document lists all the package types used for Microsemi FPGAs and provides detailed drawings and dimensions. The following table lists the package types, their acronyms, and the naming convention used when referring to a package of that type with a particular pin count.
2.2 CPGAThe following figures show package outlines for various packages under ceramic pin grid array (CPGA).
2.2.1 PG84 The following figure shows the package outline of PG84.
Table 1 • Package Naming Conventions
Package Type Package Name AcronymPackage/Pin Naming Convention (example)
Ceramic Packages Ceramic Pin Grid Array CPGA PG84
Ceramic Quad Flat Pack CQFP CQ208
Ceramic Chip Carrier Land Grid Substrate CCLG CC256
Ceramic Column Grid Array CCGA CG484
Ceramic Land Grid Array CLGA LG484
Plastic Packages(leadframe-based, peripheral leads)
Quad Flat No Lead QFN QN48
Plastic Quad Flat Pack PQFP PQ208
Thin Quad Flat Pack TQFP TQ144
Very Thin Quad Flat Pack VQFP VQ176
Plastic Quad Flat Pack (exposed heatsink) RQFP RQ208
Plastic Leaded Chip Carrier PLCC PL44
Plastic Packages(substrate-based, area array pins)
Plastic Ball Grid Array (PBGA) (1.27 mm pitch)
PBGA BG272
Fine pitch plastic ball grid array (FBGA) (1.00 mm pitch)
FBGA FG144
Chip Scale Package (0.50 mm pitch) CSP CS81
Chip Scale Package (0.80 mm pitch)1
1. Currently the CS49, CS128, CS180, and CS289 packages are 0.80 mm pitch rather than 0.50 mm pitch.
CSP CS49
Micro Chip Scale Package UCS UC36
Very Fine Ball Pitch Grid Array VFPBA VF400
5193068 PD3068 Datasheet Revision 62.0 7
Package Mechanical Drawings
Figure 1 • Package Outline of PG84
Note: All dimensions are in inches unless otherwise stated.
Note: BSC = Basic spacing between centers.
The following table shows the supported devices for PG84.
2.2.2 PG100The following figure shows the package outline of PG100.
Table 2 • Supported Devices for PG84
Supported DevicesA1010B A1020B
Orientation
Pin
1.100" ± 0.020" square0.072"0.088"
0.015"
0.120"0.140"
0.100" BSC
0.018" ± 0.002"
0.050" ± 0.010"
0.045"0.055"
L
K
J
H
G
F
E
D
C
B
A
1110987654321
Pin #1 ID
Top View
Bottom View
Side View
1.000" BSC
5193068 PD3068 Datasheet Revision 62.0 8
Package Mechanical Drawings
Figure 2 • Package Outline of PG100
Note: All dimensions are in inches unless otherwise stated.
Note: BSC = Basic spacing between centers.
The following table lists the supported devices for PG100.
2.2.3 PG132The following figure shows the package outline of PG132.
Table 3 • Supported Devices for PG100
Supported DevicesA1225XL1
1. This product is obsolete.
A1415A1
0.015"
Orientation
Pin
1.100" ± 0.015" square
0.072"0.88"
0.120"0.140"
0.050" ± 0.010"
Pin #1 ID
0.0�5"0.055"
�
�
�
�
�
�
�
�
�
�
�
1110����5���1
Top View
Bottom View
Side View
0.100" BSC
1.000" BSC
0.01� ± 0.00�"
5193068 PD3068 Datasheet Revision 62.0 9
Package Mechanical Drawings
Figure 3 • Package Outline of PG132
oNote: All dimensions are in inches unless otherwise stated.
Note: BSC = Basic spacing between centers.
The following table lists the supported devices for PG132.
2.2.4 PG175The following figure shows the package outline of PG175.
Table 4 • Supported Devices for PG132
Supported DevicesA1240A A1240XL*
Note: *This product is obsolete.
0.015"
Orientation
Pin
0.120"0.140"
0.100" BSC
0.018" ± 0.002"
0.050" ± 0.010"
1.200" BSC
0.072"0.088"
Pin #1 ID
0.045"0.055"
11 12 1310987654321
NMLKJHGFEDCBA
Top View
Bottom View
Side View
1.360" ± 0.015" square
5193068 PD3068 Datasheet Revision 62.0 10
Package Mechanical Drawings
Figure 4 • Package Outline of PG175
Note: All dimensions are in inches unless otherwise stated.
Note: BSC = Basic spacing between centers.
The following table lists the supported devices for PG175.
2.2.5 PG176The following figure shows the package outline of PG176.
Table 5 • Supported Devices for PG175
Supported DevicesA1440A1
1. This product is obsolete.
Index Mark
0.018" ± 0.002"
0.130" ± 0.010"0.050" ± 0.005"
0.105" ± 0.010"
1.400" BSC
0.100" BSC
0.05" ± .0005"
1.570" ± 0.015" square
RPNMLKJHGFEDCBA
Top View
Bottom View
Side View
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
5193068 PD3068 Datasheet Revision 62.0 11
Package Mechanical Drawings
Figure 5 • Package Outline of PG176
Note: All dimensions are in inches unless otherwise stated.
Note: BSC = Basic spacing between centers.
The following table lists the supported devices for PG176.
2.2.6 PG207The following figure shows the package outline of PG207.
Table 6 • Supported Devices for PG175
Supported DevicesA1280A A1280XL1
1. This product is obsolete.
0.120"0.140"
0.105" ± 0.010"
0.050" ± 0.005"
1.400" BSC
0.100" BSC
1.570" ± 0.015" square
11 12 13 14 1510987654321
RPNMLKJHGFEDCBA
0.018" ± 0.002"
0.05" ± 0.005"
Top View
Bottom View
Side View
Index Mark
5193068 PD3068 Datasheet Revision 62.0 12
Package Mechanical Drawings
Figure 6 • Package Outline of PG207
Note: All dimensions are in inches unless otherwise stated.
Note: BSC = Basic spacing between centers.
The following table lists the supported devices for PG207.
2.2.7 PG257The following figure shows the package outline of PG257.
Table 7 • Supported Devices for PG207
Supported DevicesA1460A
0.100" BSC
0.05" ± 0.005"
0.115" ± 0.011"
11 12 13 14 15 16 1710987654321
UTRPNMLKJHGFEDCBA
1.600" BSC
0.018" ± 0.002"
0.180" ± 0.010"
0.05" ± 0.005"
Top View
Side View
Bottom View
Index Mark
1.77" ± 0.010" square
5193068 PD3068 Datasheet Revision 62.0 13
Package Mechanical Drawings
Figure 7 • Package Outline of PG257
Note: All dimensions are in inches unless otherwise stated.
Note: BSC = Basic spacing between centers.
The following table lists the supported devices for PG257.
2.3 Ceramic Quad Flat Pack The following figures show package outlines for various packages under ceramic quad flat pack (CQFP).
2.3.1 CQ84The following figure shows the package outline of CQ84.
Table 8 • Supported Devices for PG257
Supported DevicesA14100A
1.970" ± 0.015" square
0.105" ± 0.012"
0.100" BSC
0.120"0.140"
0.018" ± 0.002"
0.05" ± 0.005"
0.005" ± 0.005"
Top View
Bottom View
Side View
ABCDEFGHJKLMNPRTVXY
1 2 3 4 5 6 7 8 9 10111213141516171819
1.800" ± 0.012
Index Mark
5193068 PD3068 Datasheet Revision 62.0 14
Package Mechanical Drawings
Figure 8 • Package Top View of CQ84
Note: Units are in mm.
Note: LID and die attach area must be connected to ground (GND).
2.3.2 CQ84 Side View and Bottom ViewThe following figure shows the package outline of CQ84.
Top View
5193068 PD3068 Datasheet Revision 62.0 15
Package Mechanical Drawings
Figure 9 • Bottom and Side Views of CQ84
Note: Units are in mm.
Note: LID and die attach area must be connected to ground (GND).
The following table shows the supported devices for CQ84.
Table 9 • Supported Devices for CQ84
Supported DevicesA1020B RT10201
A32100DX1
1. This product is obsolete.
RH10201
A54SX32A RT54SX32S1, RTSX32SU
Table 10 • Plate Thickness for CQ84
Plate ThicknessNi Plating 2.03~8.89 micron
Au Plating 2.54 micron min.
Bottom View
Side View
MAX. 2.31
MAX. 2.001.77 ± 0.18
2.15 ± 0.25
(2.55)(0.45)DEPTH
(2.15) (2.0
5)
(2.4
0)D
EPTH
INDEX MARK(PLATING OPTION)
84
1
64
64
43
42
21
22
4X(0.76 × 45º)
CHAMFER
4X(1
.25) (1.10)
(DEPTH 0.45)
4X
LEAD MATERIALFe-Ni-Co ALLOY
BRAZED
Ag-Cu ALLOY
0.889
4X24
.13
± 0.
25
CERAMIC
5193068 PD3068 Datasheet Revision 62.0 16
Package Mechanical Drawings
2.3.3 CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352—Cavity Up without Heat SinkThe following figure shows the dimensions, top view, and, side view of CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352—cavity up devices without heat sink.
Table 11 • Lid Size for CQ84
Lid Size A BA1020B 13.21 13.21
A32100DX1
1. This product is obsolete.
13.97 13.97
A54SX32A 13.21 13.21
RH1020* 13.21 13.21
RT10201 13.21 13.21
RT54SX32S1, RTSX32SU 10.54 13.61
5193068 PD3068 Datasheet Revision 62.0 17
Package Mechanical Drawings
Figure 10 • CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352—Cavity Up without Heat Sink
The following figure shows the dimensions, top view, and side view of RTG4 CQ352—cavity up devices without heat sink.
A
b
H
D1D2
E2 E1
F
L1 K
CeramicTie Bar
Number 1
e
A1
CLead Kovar
Lid
Top View
Side View
5193068 PD3068 Datasheet Revision 62.0 18
Package Mechanical Drawings
Figure 11 • RTG4 CQ352—Cavity Up without Heat Sink: Top View
The following figure shows the dimension of and bottom view of RTG4 CQ352—cavity up devices without heat sink.
5193068 PD3068 Datasheet Revision 62.0 19
Package Mechanical Drawings
Figure 12 • RTG4 CQ352—Cavity Up without Heat Sink: Bottom View
Note: All dimensions are in inches except for CQ208, CQ256, and CQ352, which are in millimeters. For more information on dimensions, see CQFP without Heat Sink Dimensions, page 26.
Note: Outside lead frame holes (from dimension H) are circular for the CQ208, CQ256, and CQ352.
Note: Seal ring and lid are connected to Ground.
Note: Packages are shipped with the uniform ceramic tie bar in a test carrier.
5193068 PD3068 Datasheet Revision 62.0 20
Package Mechanical Drawings
The following table shows the supported devices for supported devices for CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352.
2.3.4 CQ208 and CQ256—Cavity Up with Heat SinkThe following figure shows the dimension of the CQ208 and CQ256—cavity up with heat sink.
Table 12 • Supported Devices for CQ132, CQ172, CQ196, CQ208, CQ256, and CQ352
Supported DevicesCQ132 CQ172 CQ196 CQ208 CQ256 CQ352A1425ART1425A
A1280ARH12801
RT1280A
1. This product is obsolete.
A1460ART1460A
A42MX36AX250AX500A54SX16A54SX32A54SX32AA54SX72AAPA300APA600APA1000RT54SX32S1
RTSX32SURTAX250S
A14100AAX2000A54SX32AA54SX72ART14100ART54SX32S1
RTSX32SURTAX2000SRT3PE600LRT3PE3000L
AX250AX500AX1000AX2000APA300APA600APA1000RTAX250SRTAX1000SRTAX2000SRTAX4000SRTAX2000DRTAX4000D
5193068 PD3068 Datasheet Revision 62.0 21
Package Mechanical Drawings
Figure 13 • CQ208 and CQ256—Cavity Up with Heat Sink
Note: All dimensions are in inches except for CQ208, CQ256, and CQ352, which are in millimeters. For more information on dimensions, see CQFP with Heat Sink Dimensions, page 27.
Note: Outside lead frame holes (from dimension H) are circular for the CQ208, CQ256, and CQ352 devices..
Note: Seal ring and lid are connected to Ground.
Note: Lead material is Kovar with minimum of 60 microinches gold over nickel.
Note: Packages are shipped with the uniform ceramic tie bar.
A
b
HD1D2
E2 E1
F
L1 K
CeramicTie Bar
Number 1
e
A1 Heat Sink
CLead Kovar
Lid
Top View
Side View
5193068 PD3068 Datasheet Revision 62.0 22
Package Mechanical Drawings
The following table shows the supported devices for CQ208 and CQ256.
2.3.5 CQ256—Cavity Down without Heat Sink The following figure shows the dimension of the CQ256—cavity down without heat sink.
Table 13 • Supported Devices for CQ208 and CQ256
Supported DevicesCQ208 CQ256A32200DX1
RT54SX72S1
RTSX72SU
1. This product is obsolete.
A54SX16A54SX32RT54SX72S1
RTSX72SU
5193068 PD3068 Datasheet Revision 62.0 23
Package Mechanical Drawings
Figure 14 • CQ256—Cavity Down without Heat Sink
Note: Dimensions are in millimeters. For more information on dimensions, see CQFP with Heat Sink Dimensions, page 27.
Note: Seal ring and lid are connected to Ground.
Note: Lead material is Kovar with gold plate over nickel.
Note: Packages are shipped with the uniform ceramic tie bar.
Note: Package is cavity down, with the lid facing the bottom of the package. However, the leads can be formed on either side if the application requires the lid to be facing the top
L1
F
K
e b
LidLead MaterialFe–Ni–Co Alloy A
c
A1
Lid E2 E1
1256
H
D1
D2
Top View
Side View
5193068 PD3068 Datasheet Revision 62.0 24
Package Mechanical Drawings
The following table shows the supported devices for CQ256.
2.3.6 CQ256—Cavity Down with Heat SinkThe following figure shows the dimension of the CQ256—cavity down with heat sink.
Figure 15 • CQ256—Cavity Down with Heat Sink
Table 14 • Supported Devices for CQ256
Supported DevicesA42MX36
F
e b
LidLead MaterialFe–Ni–Co Alloy
A
c
A1
Heat Sink
Lid
1
Top View
Side View
256
E2 E1
D2
D1L1
H K
5193068 PD3068 Datasheet Revision 62.0 25
Package Mechanical Drawings
Note: Dimensions are in millimeters. For more information on dimensions, see CQFP with Heat Sink Dimensions, page 27.
Note: Packages are shipped with the uniform ceramic tie bar in a test carrier.
Note: Dimensions are in millimeters. For more information on dimensions, see CQFP with Heat Sink Dimensions, page 25.
The following table shows the supported devices for CQ256.
2.3.7 CQFP without Heat Sink DimensionsThe following table lists the dimensions for CQFP without heat sink.
Table 15 • Supported Devices for CQ256
Supported DevicesA32200DX1
1. This product is obsolete.
Table 16 • Dimensions for CQFP without Heat Sink
JEDEC Equivalent
CQ132MO-113 VAR AC
CQ172MO-113 VAR AE
CQ196MO-113 VAR AB CQ208
Symbol Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 0.094 0.105 0.116 0.094 0.105 0.116 0.094 0.105 0.116 2.30 2.80 3.30
A1 0.080 0.090 0.100 0.080 0.090 0.100 0.080 0.090 0.100 2.00 2.30 2.80
b 0.007 0.008 0.010 0.007 0.008 0.010 0.007 0.008 0.010 0.17 0.20 0.22
c 0.004 0.006 0.008 0.004 0.006 0.008 0.004 0.006 0.008 0.11 0.15 0.18
D1/E1 0.940 0.950 0.960 1.168 1.180 1.192 1.336 1.350 1.364 28.96 29.21 29.46
D2/E2 0.800 BSC 1.050 BSC 1.200 BSC 25.5 BSC
e 0.025 BSC 0.025 BSC 0.025 BSC 0.50 BSC
F 0.325 0.350 0.375 0.175 0.200 0.225 0.175 0.200 0.225 7.05 7.75 8.45
H 2.320 BSC 2.320 BSC 2.320 BSC 70.00 BSC
K 2.140 BSC 2.140 BSC 2.140 BSC 65.90 BSC
L1 2.485 2.500 2.505 2.485 2.495 2.505 2.485 2.495 2.505 74.60 75.00 75.40
JEDEC Equivalent
CQ256MO-134 VAR AB
CQ3521
MO-134 VAR AESymbol Min. Nom. Max. Min. Nom. Max.A 2.30 2.80 3.30 2.43 2.66 2.89
A1 2.00 2.30 2.80 2.05 2.28 2.51
b 0.18 0.20 0.22 0.18 0.20 0.22
c 0.11 0.15 0.18 0.11 0.15 0.18
D1/E1 35.64 36.00 36.64 47.75 48.00 48.25
D2/E2 31.5 BSC 43.51 BSC
e 0.50 BSC 0.50 BSC
F 7.05 7.75 8.45 5.00
H 70.00 BSC 70.00 BSC
5193068 PD3068 Datasheet Revision 62.0 26
Package Mechanical Drawings
2.3.8 CQFP with Heat Sink DimensionsThe following table lists the dimensions for CQFP with heat sink.
Note: All dimensions are in inches except for CQ208, CQ256, and CQ352, which are in millimeters.
Note: BSC = Basic spacing between centers. This is a theoretical true position dimension and so has no tolerance.
The dimensions above are for reference only. For more accurate dimensions, use the dimensions in the SMD drawings for a specified device.
For heat sink information, refer to the Hermetic Package Mechanical Configuration document (Cavity, weight, lid size and heat sink size) located at: http://www.microsemi.com/document-portal/doc_view/131087-hermetic-package-mechanical-configuration.
2.4 CCLGThe following figures show package outlines for various packages under ceramic chip carrier land grid substrate (CCLG).
2.4.1 CC256The following figure shows the package outline of CC256.
K 65.90 BSC 65.90 BSC
L1 74.60 75.00 75.40 74.60 75.00 75.40
1. For device RTAX2000D-CQ352 and RTAX4000D-CQ352 only.Note: All dimensions are in inches except for CQ208, CQ256, and CQ352, which are in millimeters.
Note: BSC = Basic spacing between centers. This is a theoretical true position dimension and so has no tolerance.
Table 17 • Dimensions for CQFP with Heat Sink
JEDEC Equivalent CQ208
CQ256MO-134 VAR AB
Symbol Min. Nom. Max. Min. Nom. Max.A 2.79 3.30 3.90 2.79 3.30 3.90
A1 2.00 2.30 2.80 2.00 2.30 2.80
b 0.18 0.20 0.22 0.18 0.20 0.22
c 0.11 0.15 0.17 0.11 0.15 0.18
D1/E1 28.96 29.21 29.46 35.64 36.00 36.66
D2/E2 25.5 BSC 31.5 BSC
e 0.50 BSC 0.50 BSC
F 7.05 7.75 8.45 7.05 7.75 8.45
H 70.00 BSC 70.00 BSC
K 65.90 BSC 65.90 BSC
L1 74.60 75.00 75.40 74.60 75.00 75.40
Table 16 • Dimensions for CQFP without Heat Sink
5193068 PD3068 Datasheet Revision 62.0 27
Package Mechanical Drawings
Figure 16 • Package Outline of CC256
Note: Units are in mm.
The following table shows the supported devices for CC256.
Table 18 • Supported Devices for CC256
Supported DevicesRT54SX32S1
RTSX32SU
1. This product is obsolete.
(1.000X45°)CHAMFER
External Bonding Pad 125
6
Top View(see next page for clear dimension)
17.000±0.203
LID 12.954±0.152
6.001 6.140
192
193
TYP.
(R 0.254)
A1 Index Corner
(0.500X45°)CHAMFER
LID
15.
240±
0.15
2
6.14
06.
001
6.14
06.
001
4X 0
.254
3X
R 0.500
12964TYP.
TYP.
(0.127)
(0.762)12865 0.114 TYP.
0.076 TYP.
4X (0.1651)4X (0.0953)
6.001 6.140
4X (13.70)
1 2 3 54 6 7 8 9 10 11 12 13 14 15 16
1.00
015
.000
Ø0.600±0.050256X
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1.00015.000
Bottom View
Detail A
Side View(with partial section view)
LID
A
1.397±0.140
0.50
8±0.
051
0.25
4±0.
025
0.88
9±0.
051
(bot
tom
to E
xter
nal B
ondi
ng p
ads)
4X (0.250X45o)Chamfer
5193068 PD3068 Datasheet Revision 62.0 28
Package Mechanical Drawings
2.4.2 CCLG Substrate DimensionsThe following figure shows the dimensions of CCLG substrate.
Figure 17 • CCLG Substrate Dimensions
2.4.3 LG1657The following figure shows the package outline of LG1657.
External Bonding Pad 1
Top View (Zoom 2.4x)
17.000±0.203
LID 12.954±0.152
6.001 6.140
192
193
256
TYP.
(R 0.254)
A1 Index Corner(1.000X45°)CHAMFER
(0.500X45°)CHAMFER
LID
15.
240±
0.15
2
6.14
06.
001
6.14
06.
001
4X 0
.254
3X
R 0.500
12964
TYP.
TYP.
(0.127)
(0.762)
12865 0.114 TYP.
0.076 TYP.
4X (0.1651)
4X (0.0953)
6.001 6.140
4X (13.70)
5193068 PD3068 Datasheet Revision 62.0 29
Package Mechanical Drawings
Figure 18 • Package Outline of LG1657
Note: The units are in mm.
Note: Note: Seal ring is connected to the ground (GND).
The following table shows the supported devices for LG1657.
Table 19 • Supported Devices for LG1657
Supported DevicesRT4G150
AB
CD
EF
GH
JK
LM
NP
RT
UV
WY
AA
ABAC
ADAE
AFAG
AHAJ
AKAL
AM
ANAP
AR
ATAU
AV
AYBA
AW
1
2 3
45
6
7
89
1011
12
13
1415
16
17
18
19
20
21
22
23
24
25
26
27
2830
31
32
33
34
35
36
37
38
39
40
41 29
INDEX MARK
(ID)
1.0
0X
40=
40.0
0 (
RE
F)
1.00X40=40.00 (REF)
1657XØ0.80±0.05
1.0
0
1.00
A
B
PIN A1 CORNER
REF MARKING AREA
42.50
42.5
0
4X(R0.50)
40.30±0.20 (SEAL RING)
40.3
0±0.2
0 (
SE
AL R
ING
)
4X(0.50X45°)
CHAMFER
0.2 4X
C
2.00±0.20
1.26 NOM.
~
(0.20X45°)
CHAMFER
4X
Bottom View
Top View Side View
3.26±0.25
5193068 PD3068 Datasheet Revision 62.0 30
Package Mechanical Drawings
2.5 CCGAThe following figures show package outlines for various packages under ceramic column grid array (CCGA).
2.5.1 CG484The following figure shows the package outline of CG484.
Figure 19 • Package Outline of CG484
Note: The top and side views will be completed in the future.
Table 20 • Supported Devices for CG484
Supported DevicesRT3PE600LRT3PE3000L
CCGASide View
A1 CornerIndex Area
A2A1
b
E
CLGASide View
A2
Top View
Bottom View
D
A
A
ABAA
YWVUTRPNMLKJHGFEDCBA
1 2 3 4 5 6 7 8 9 101112131415161718 19202122
e
e
E1
D1
5193068 PD3068 Datasheet Revision 62.0 31
Package Mechanical Drawings
2.5.2 CG624The following figure shows the package outline of CG624.
Figure 20 • Package Outline of CG624
The following table shows the supported devices for CG624.
2.5.3 CG896The following figure shows the package outline of CG896.
Table 21 • Supported Devices for CG624
Supported DevicesAX1000AX2000
RTAX1000SRTAX2000SRTAX250S
APA600APA1000
RTSX72SU
CCGASide View
eAEADACABAA
YWVUTRPNMLKJHGFEDCBA
1 2 3 4 5 6 7 8 9 101112131415161718 1920212223 2524
e
A1 CornerIndex Area
A2A1
b
E1
E
CLGASide View
A2
Top View
Bottom View
D1
DA
A
5193068 PD3068 Datasheet Revision 62.0 32
Package Mechanical Drawings
Figure 21 • Package Outline of CG896
The following table shows the supported devices for CG896.
2.5.4 CCGA DimensionsThe following table lists the dimensions of CCGA.
Table 22 • Supported Devices for CG896
Supported DevicesRT3PE3000L
Table 23 • Dimensions of CCGA
Dimension CG484 CG624 CG896 Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.
CCGA - A 5.19 5.72 6.19 4.54 4.88 5.41 5.65 6.23 6.75
CLGA - A 3.06 3.51 3.83 2.41 2.67 3.05 3.16 3.51 3.86
D1e
Top View
D A
A1 CornerIndex Area
E
CCGASide View
CLGASide View
Bottom View
E1
e
ABCDEFGHJKLMNPRTUVWY
AAABACADAEAFAGAHAJAK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 3029
A
A2 A2
A1
b
5193068 PD3068 Datasheet Revision 62.0 33
Package Mechanical Drawings
2.5.5 CG1152The following figure shows the package outline of CG1152.
Figure 22 • Package Outline of CG1152
Note: The units are in mm.
Note: Note: Seal ring and die attach are connected to the ground (GND).
A1 2.15 2.21 2.36 2.15 2.21 2.36 2.15 2.21 2.36
A2 2.70 3.00 3.30 2.06 2.29 2.52 3.16 3.51 3.86
b 0.43 0.51 0.59 0.43 0.51 0.59 0.43 0.51 0.59
D 22.77 23.00 23.23 32.17 32.50 32.83 30.69 31.00 31.31
D1 21.00 BSC 30.48 BSC 29.00 BSC
E 22.77 23.00 23.23 32.17 32.50 32.83 30.69 31.00 31.31
E1 21.00 BSC 30.48 BSC 29.00 BSC
e 1.00 BSC 1.27 BSC 1.00 BSC
Table 23 • Dimensions of CCGA
Top View
(1.00×45º)CHAMFER
35.000 ± 0.350
35.0
00 ±
0.3
50
33.000
33.0
00
1.000
1.00
0
Bottom View
CCGASide View
CLGASide View
1152X Ø0.510 ± 0.080
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 31 32 33 3429
3X (0.50 × 45º)CHAMFER
0.100
c
2.210 +0.150–0.0602.772 ± 0.270
0.508 ± 0.025
0.150 A
5.935 MAX.5.135 MIN.
A SEATING PLANE
ABCDEFGH
JKLMNPRTU
VWY
AAABACADAE
AFAGAHAJ
AKALAMANAP
5193068 PD3068 Datasheet Revision 62.0 34
Package Mechanical Drawings
The following table shows the supported devices for CG1152.
2.5.6 CG1272The following figure shows the package outline of CG1272.
Figure 23 • Package Outline of CG1272
Note: The units are in mm.
Note: Seal ring and die attach paddle are connected to the ground (GND).
Table 24 • Supported Devices for CG1152
Supported DevicesRTAX2000S
Top View
CCGASide View
CLGASide View
Bottom View
ABCDEFGHJKLMNPRTUVWY
AAABACADAEAFAGAHAJAKALAMANAPARAT
1272X Ø0.510 ± 0.080
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 31 32 33 34 35 3629
37.500 ± 0.380
37.5
00 ±
0.3
80
(1.50 × 45º)CHAMFER
3X (1.50 × 45º)CHAMFER
0.100
2.772 ± 0.2700.508 ± 0.025
2.210 +0.150–0.060
0.150 A
A
5.935 MAX.5.135 MIN.
SEATING PLANE35.000
1.000
35.0
00
1.00
0
5193068 PD3068 Datasheet Revision 62.0 35
Package Mechanical Drawings
The following table shows the supported devices for CG1272.
2.5.7 CG1657The following figure shows the package outline of CG1657.
Figure 24 • Package Outline of CG1657
Note: The units are in mm.
Note: Seal ring is connected to the ground (GND).
Table 25 • Supported Devices for CG1272
Supported DevicesRTAX4000SRTAX2000D
AB
CD
EF
GH
JK
LM
NP
RT
UV
WY
AAAB
ACAD
AEAF
AGAH
AJAK
ALAM
ANAP
ARAT
AUAV
AYBA
AW
1 2
3 4
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
272830
3132
3334
3536
3738
3940
41 29
INDEX MARK
(ID)
1.0
0 X
40
= 4
0 (
RE
F)
1.00 X 40 = 40 (REF)
1.0
0
1.00
ALUMINA COAT
~
B
PIN A1 CORNER
42.50
42
.50
4X
(R0.50)
0.2
40.30±0.20 (SEAL RING)
40
.30
±0
.20
(S
EA
L R
ING
)
4X (0.5X45°)
CHAMFER
(REF MARKING AREA)
A
0.15
C2.21±0.15
2.00±0.20
1.26 NOM.
~
(0.20X45°)
CHAMFER
4X
Ø0.51±0.10
5.47±0.40
Bottom View
Top View Side View
Ø0.30
Ø0.15
M
M C
C A B
C
5193068 PD3068 Datasheet Revision 62.0 36
Package Mechanical Drawings
The following table shows the supported devices for CG1657.
2.6 PLCCThe following figure shows the dimensions and details of plastic leaded chip carrier (PLCC).
Figure 25 • PLCC
Table 26 • Supported Devices for CG1657
Supported DevicesRT4G150
E1E
DD1
0.048 (1.219)0.042 (1.067)
e1
A0.004
A1
Detail A Detail B
0.007 Max.
B2
B0.020 (0.508)
Min.
Base Line
D2/E2
0.0830.062
0.0450.025
R
Side View
Detail A Detail B
Top View
5193068 PD3068 Datasheet Revision 62.0 37
Package Mechanical Drawings
Note: Dimensions are in millimeters. For more information on dimensions, see Plastic Leaded Chip Carrier Dimensions, page 38.
The following table lists the supported devices for PL44, PL68, and PL84.
2.6.1 Plastic Leaded Chip Carrier DimensionsThe following table lists the dimensions of plastic leaded chip carrier.
Note: All dimensions are in inches.
Note: BSC = Basic spacing between centers.
2.7 QFNThe following figures show package outlines for various packages under quad flat no lead (QFN).
2.7.1 QN48The following figure shows the package outline of QN48.
Table 27 • Supported Devices for PL44, PL68, and PL84
Supported DevicesPL44 PL68 PL84A1010B A1010B A10V20B A1020B A3265A1
A1020B A1020B A1225XLV1
1. This product is obsolete.
A1225A A54SX08
A40MX02 A10V10B A1280XLV1 A1240A A32100DX1
A40MX04 A10V20B A1240XLV1 A1280A A32140DX1
A40MX02 A14V15A A1225XL1 A40MX04
A40MX04 A14V25A A1240XL1 A42MX09
A14V40A A1280XL1 A42MX16
A3265DXV1 A1415A A42MX24
A32100DXV1 A1425A
A32140DXV1 A1440A
Table 28 • Dimensions of Plastic Leaded Chip Carrier
JEDEC Equivalent
PL44MS-018 VAR AC
PL68MS-018 VAR AE
PL84MS-018 VAR AF
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 0.165 0.172 0.180 0.165 0.172 0.180 0.165 0.172 0.180
A1 0.090 0.105 0.120 0.090 0.105 0.120 0.090 0.105 0.120
B 0.013 – 0.021 0.013 – 0.021 0.013 – 0.021
B2 0.026 – 0.032 0.026 – 0.032 0.026 – 0.032
D/E 0.685 0.690 0.695 0.985 0.990 0.995 1.185 1.190 1.195
D1/E1 0.650 0.653 0.656 0.950 0.954 0.958 1.150 1.154 1.158
D2/E2 0.590 0.610 0.630 0.890 0.910 0.930 1.090 1.110 1.130
e1 0.050 BSC 0.050 BSC 0.050 BSC
5193068 PD3068 Datasheet Revision 62.0 38
Package Mechanical Drawings
Figure 26 • Package Outline of QN48
Note: Corner chamfer leads are applied to maintain minimum spacing between corner leads; otherwise, keep normal lead shape.
Note: Die attach paddle center of package is tided to the ground (GND).
The following table shows the supported devices for QN48.
2.7.2 QN68The following figure shows the package outline of QN68.
Table 29 • Supported Devices for QN48
Supported DevicesA3PN010A3P030/A3PN030
AGN010AGL030/AGLN030
B
C
D
D
D/2
E/2
E
A
E2
D2
E22
D22
e
1
Pin 1 Indicator
Detail A
Terminal Tip
NX L
Datum B
Datum A
NX k
Detail C
A
A1
A3// ccc C
0.08 C
NX bbbb Mddd M
CC
A B
NX
Seating PLANE
(Datum A or B)
(0.45 REF)
e
Top View Bottom View
Side View
Detail A Detail C
5193068 PD3068 Datasheet Revision 62.0 39
Package Mechanical Drawings
Figure 27 • Package Outline of QN68
Note: Corner chamfer leads are applied to maintain minimum spacing between corner leads; otherwise, keep normal lead shape.
Note: Die attach paddle center of package is tided to the ground (GND).
The following table shows the supported devices for QN68.
2.7.3 QN48 and QN68 Quad Flat No Leads Single Row DimensionThe following table shows the single row dimension of QN48 and QN68 quad flat no leads.
Table 30 • Supported Devices for QN68
Supported DevicesAGL015AGL030
AGLN015AGLN020AGLN030
A3P015A3P030
A3PN015A3PN020A3PN030
Table 31 • QN48 and QN68 Quad Flat No Leads Single Row Dimensions
Dimension
QN48, page 38MO-220, Variation VLLE-1
QN68, page 39MO-220, Variation VLLE-1
Min. Nom. Max. Min. Nom. Max.A 0.80 0.90 1.00 0.80 0.90 1.00
A1 0 .02 0.05 0.00 0.02 0.05
A3 0.20 REF 0.20 REF
b 0.15 0.20 0.25 0.15 0.20 0.25
D/E 5.90 6.00 6.1 7.90 8.00 8.10
B
C
D
D/2
E/2
E
A
E2
D2
E22
D22
e
1
Pin 1 Indicator
Detail A
Terminal Tip
NX L
Datum B
Datum A
NX k
Detail C
A
A1
A3// ccc C
0.08 C
NX bbbb Mddd M
CC
A B
NX
Seating PLA
(Datum A or B)
(0.45 REF)
e
Top View Bottom View
Side View
Detail A Detail C
5193068 PD3068 Datasheet Revision 62.0 40
Package Mechanical Drawings
Note: All dimensions are in millimeters.
2.8 Quad Flat No LeadThe following figure shows the dimensions of quad flat no lead.
D2/E2 4.50 4.65 4.8 2.77 2.92 3.07
e 0.40 BSC 0.40 BSC
k 0.20 – – 0.20 – –
L 0.30 0.40 0.5 0.35 0.40 0.45
N 48 68
bbb 0.07 0.07
ccc 0.10 0.10
ddd 0.05 0.05
Table 31 • QN48 and QN68 Quad Flat No Leads Single Row Dimensions
Dimension
QN48, page 38MO-220, Variation VLLE-1
QN68, page 39MO-220, Variation VLLE-1
Min. Nom. Max. Min. Nom. Max.
5193068 PD3068 Datasheet Revision 62.0 41
Package Mechanical Drawings
Figure 28 • Quad Flat No Lead
2.8.1 Quad Flat No Lead DetailsThe following figure shows the details of quad flat no lead.
Ca aa
Ca aa
Ce ee
Cc cc
AB
C
D
D2
E2
E
Pin Number A1 Area (D/2 x E/2)
Top View
Side View
Bottom View
Seating Plane
A1
A
NDA - 1 x 0.5
NDB - 1 x 0.5
NDC - 1 x 0.5
NEA
- 1
x 0
.5
NEB
- 1
x 0
.5
NEC
- 1
x 0
.5
Detail B (when present)
Optional Corner Pad (4x)
(Detail A)
(Datum B)
(Datum A)
fff M C A B
fff M C A B
5193068 PD3068 Datasheet Revision 62.0 42
Package Mechanical Drawings
Figure 29 • Quad Flat No Lead Details
2.8.2 QN108 Bottom ViewThe following figure shows the package bottom view of QN108.
bbb M C A B
bbb M C A B
bbb M C
ddd M CA B
bbb M C
ddd M CA B
QN180/QN132 QN108
N x b(Datum A or B)
N x b
(Datum A or B)
Terminal Tip 6
0.5
0.5
0.5
0.5/2
0.5
0.5/2
0.5
(LC When Present)
LC
L1
LC L1
kK
Detail A
Detail B
7
5193068 PD3068 Datasheet Revision 62.0 43
Package Mechanical Drawings
Figure 30 • Bottom View of QN108
Note: Die attach paddle center of package is tied to the ground (GND).
Note: Package is discontinued and not available.
The following table shows the supported devices for QN108.
2.8.3 QN132 Bottom ViewThe following figure shows the package bottom view of QN132.
Table 32 • Supported Devices for QN108
Supported DeviceAFS090
A1
B41 B52
A44 A56
B26 B14
A28 A15
A14
B1
B13
A43
A29
B40
B27
Pin A1 Mark
5193068 PD3068 Datasheet Revision 62.0 44
Package Mechanical Drawings
Figure 31 • Bottom View of QN132
Note: Die attach paddle center of package is tied to the ground (GND).
Note: Package is discontinued and not available.
The following table shows the supported devices for QN132.
2.8.4 QN180 Bottom ViewThe following figure shows the package bottom view of QN180.
Table 33 • Supported Devices for QN132
Supported DevicesAGL030 AGL060AGL125AGL250
A3P030A3P060A3P125A3P250
A37
A1
A12
A36
D4
D3
D1
D2
A25
A48
A24 A13
B34
B1
B11
B44
B22 B12
C31
C1
C10
B33
B23
C30
C21
C40
C20 C11
OptionalCorner Pad (4x)
Pin A1Mark
5193068 PD3068 Datasheet Revision 62.0 45
Package Mechanical Drawings
Figure 32 • Bottom View of QN180
Note: Die attach paddle center of package is tied to the ground (GND).
Note: Package is discontinued and not available.
The following table shows the supported devices for QN180.
2.8.5 Quad Flat No Leads DimensionsThe following table lists the dimensions of the quad flat no leads.
Table 34 • Supported Devices for QN180
Supported DevicesAFS090AFS250M1AFS250
Table 35 • Dimensions of Quad Flat No Leads
Symbol Min. Nom. Max.A 0.70 0.75 0.80
A1 0.00 – 0.05
b 0.25 – 0.35
k 0.20 – –
A1B1
C1
A16B15
C14
A48
Pin A1 Mark
Optional CornerPad (4X)
A49 A64
A32 A17
B45
B46 B60
B30 B16
C42
C43 C56
C28 C15
A33B31
C29
D4
D3
D1
D2
5193068 PD3068 Datasheet Revision 62.0 46
Package Mechanical Drawings
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
The following table lists the dimensions of QN108, QN132, and QN180 packages.
2.9 Plastic Quad Flat Pack Rectangular Package (TQ144)The following figure shows the details and dimensions of plastic quad flat pack rectangular.
L 0.25 – 0.35
L1 0.05 – 0.15
Tolerance of Form and Positionaaa 0.15
bbb 0.10
ccc 0.10
ddd 0.05
eee 0.08
fff 0.10
Table 36 • Dimensions for QN108, QN132, and QN180
VariationQN108 QN132 QN180Symbol
D BSC. 8.00 8.00 10.00
E BSC. 8.00 8.00 10.00
D2 Min. 5.65 4.65 6.65
Nom. 5.70 4.70 6.70
Max. 5.75 4.75 6.75
E2 Min. 5.65 4.65 6.65
Nom. 5.70 4.70 6.70
Max. 5.75 4.75 6.75
LC Min. – 0.30 0.30
Nom. – – –
Max. – 0.40 0.40
N 108 132 180
NDA 12 12 16
NDB 11 11 15
NDC – 10 14
NEA 12 12 16
NEB 11 11 15
NEC – 10 14
Table 35 • Dimensions of Quad Flat No Leads
Symbol Min. Nom. Max.
5193068 PD3068 Datasheet Revision 62.0 47
Package Mechanical Drawings
Figure 33 • Plastic Quad Flat Pack Rectangular Package (TQ144)
Note: Dimensions are in millimeters. For more information on TQ144 dimensions, see TQFP Dimensions, page 54.
2.10 Plastic Quad Flat Pack (PQFP, TQFP, VQFP)The following figure shows the details and dimensions of Plastic Quad Flat Pack.
NOTES: UNLESS OTHERWISE SPECIFIED
SEE DETAIL “A”S
EE
DE
TA
IL “
B”
11O
- 1
3O
0.1
0 C
0.0
5
(N-4
)X e
0.20 C A-B D
B 3
7.95 REF.
1.0 DIA.
PIN#1 & EJECTOR PIN
DP
N
+
0.089
0.0381
Top View
Side View
Bottom View
E/2
7.95
E 3
5 E1
E1/2
D1/2
7.50 REF.
7.50 REF.
D15 7
7
DC
Cccc
SE
AT
ING
PL
AN
E
D
D/2
2
A 3
4
H
A
1. All dimensioning and tolerances confirm to ASME Y14.5-1994.2. Datum plane H located at mold parting line and coincident with lead, where lead exits plastic body at bottom of parting line.3. Datums A-B and D to be determined at centerline between leads where leads exit plastic body at datum plane H.4. To be determined at seating plane C.5. Dimensions D1 and E1 do not include mold protrusion. Allowable mold protrusion is 0.254 mm per side. Dimension D1 and E1 include mold mismatch and are determined at datum plane H.6. N is number of terminals.
DETAIL “A” DETAIL “B”
DETAIL “C”
e / 2
2
A2
A1
10
10
10
8 10
b
b1
WITH LEAD FINISH
BASE METAL
0.08
0O
MIN.
0-7O
0.08/0.20 R.
GAUGE PLANER. MIN.
0.20 MIN.
1.00 REF.
12
A, B, OR D
0.05
0.25
0.09/0.16 0.09/0.20
ddd M C A-B D
7. Package top dimensions are smaller than bottom dimensions by 0.10 millimeters and top of package will not overhang bottom of package.8. Dimension b does not include damber protrusion. Allowable damber protrusion shall be not cause the lead width to exceed the maximum b dimension by more than 0.08 mm. Damber can not be located on the lower radius or the foot.9. All dimensions are in millimeters.10. These dimensions apply to the flat section of the lead between 0.10 mm and 0.25 mm from the lead tip.11. This drawing conforms to JEDEC registered outline m2s-026-c, variation BFB.12. A1 is defined as the distance from the seating plane to the lowest point of the package body.
GATE PIN
1.50
+
0.20 A-BH D4
2 H
EVEN LEAD SIDES
3
5193068 PD3068 Datasheet Revision 62.0 48
Package Mechanical Drawings
Figure 34 • Plastic Quad Flat Pack (PQFP, TQFP, VQFP)
Note: Dimensions are in millimeters. For more information on TQ144 dimensions, see TQFP Dimensions, page 54 and VQFP Dimensions, page 55.
2.11 Plastic Quad Flat Pack—Exposed Heatsink (RQFP)The following figure shows the details and dimensions of plastic quad flat pack exposed heat sink.
EE1
D
D1
Side View
Top View
A2 A
L
A1
10 Typ
Theta
R 0.08/0.25
R 0.08 Min.
be
Detail A
See Detail A
Cccc
°
5193068 PD3068 Datasheet Revision 62.0 49
Package Mechanical Drawings
Figure 35 • Plastic Quad Flat Pack—Exposed Heatsink (RQFP)
Note: Dimensions are in millimeters. For more information on dimensions, see Plastic Quad Flat Pack (RQFP/PQFP) Dimensions, page 53.
2.12 Plastic Quad Flat Pack Rectangular Package (PQ100)The following figure shows the details and dimensions of plastic quad flat pack rectangular package.
EE1
D
D1
A2 A
L
A1
10 Typ
Theta
R 0.08/0.25
R 0.08 Min.
be
Detail A
See Detail A
Cccc
°
Exposed Heat Sink
Diameter
Top View
Side View
5193068 PD3068 Datasheet Revision 62.0 50
Package Mechanical Drawings
Figure 36 • Plastic Quad Flat Pack Rectangular Package (PQ100)
Note: Dimensions are in millimeters. For more information on dimensions, see Plastic Quad Flat Pack (RQFP/PQFP) Dimensions, page 53.
EE1
D
D1
Top View
Side View
A2 A
L
A1
10 Typ
Theta
R 0.13/0.30
R 0.13 Min.
be
Detail A
See Detail A
Cccc
°
5193068 PD3068 Datasheet Revision 62.0 51
Package Mechanical Drawings
The following table shows the supported devices for or plastic quad flat pack rectangular package.
2.12.1 PQFP DimensionsThe following table shows the details and dimensions of plastic quad flat pack (PQFP).
Table 37 • Supported Devices for Plastic Quad Flat Pack Rectangular Package
Supported DevicesRQ208 PQ100 PQ144 PQ160 PQ208 RQ240 PQ240A14V100AA14100AA32200DX1
A32300DX1
A32300DXV1
1. This product is obsolete.
A1010BA1020BA1225AA1225XL1
A1240XL1
A1415AA1425AA3265DX1
A40MX02A40MX04A42MX09A42MX16
A1240AA1240XL1
A1280AA1280XL1
A14V25AA1425AA14V40AA1440AA14V60AA1460AA3265DX1
A32100DX1
A32140DX1
A42MX09A42MX16A42MX24
A1280XL*A14V60AA1460AA32100DX1
A32140DX1
A32200DX1
A32200DXV1
A42MX16A42MX24A42MX36A500K0501
A500K1301
A500K1801
A500K2701
A54SX08A54SX16A54SX16PA54SX32A54SX08AA54SX16AA54SX32AA54SX72A
AX250AX500APA075APA150APA300APA450APA600APA750APA1000A3P125A3P250A3P400A3P600A3P1000M1A3P250M1A3P400M1A3P600M1A3P1000M7A3P1000
A3PE600A3PE1500A3PE3000M1A3PE1500M1A3PE3000A3P250LA3P1000LM1A3P600LM1A3P1000LA3PE3000LM1A3PE3000LAFS250AFS600M1AFS250M1AFS600M7AFS600A2F200A2F500
A32200DX*A32200DXV1
A42MX36
Table 38 • PQFP Dimensions
JEDEC EquivalentPQ100MS-022 VAR GC-1
PQ144MS-022 VAR DC-1
PQ160MS-022 VAR DD-1
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A – – 3.40 – 4.10 – – 4.10
A1 0.25 – 0.5 0.25 – 0.50 0.25 0.33 0.50
A2 2.50 2.70 2.9 3.20 3.40 3.60 3.20 3.40 3.60
b 0.22 – 0.40 0.22 – 0.40 0.22 – 0.40
c 0.11 – 0.23 0.11 – 0.23 0.11 – 0.23
D 23.20 BSC 31.20 BSC 31.20 BSC
D1 20.00 BSC 28.00 BSC 28.00 BSC
E 17.20 BSC 31.20 BSC 31.20 BSC
E1 14.00 BSC 28.00 BSC 28.00 BSC
e 0.65 BSC 0.65 BSC 0.65 BSC
L 0.73 0.88 1.03 0.73 0.88 1.03 0.73 0.88 1.03
5193068 PD3068 Datasheet Revision 62.0 52
Package Mechanical Drawings
2.12.2 Plastic Quad Flat Pack (RQFP/PQFP) DimensionsThe following table shows the details and dimensions of plastic quad flat pack.
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
ccc 0.10 0.10 0.10
Theta 0 – 7 deg 0 – 7 deg 0 – 7 deg
Table 39 • RQFP/PQFP) Dimensions
JEDEC EquivalentRQ208/PQ208MS-029 VAR FA-1
RQ240/PQ240MS-029 VAR GA
Dimension Min. Nom. Max. Min. Nom. Max.A – – 4.10 – 4.10
A1 0.25 0.50 0.25 – 0.50
A2 3.20 3.40 3.60 3.20 3.40 3.60
b 0.17 – 0.27 0.17 – 0.27
c 0.09 – 0.20 0.09 – 0.20
D/E 30.60 BSC 34.60 BSC
D1/E1 28.00 BSC 32.10 BSC
e 0.50 BSC 0.50 BSC
L 0.45 0.60 0.75 0.50 0.60 0.75
ccc 0.08 0.08
Theta 0 3.50 8 deg 0 3.50 8 deg
Diameter 19.82 20.32 20.82 23.63 24.13 24.63
Table 38 • PQFP Dimensions
5193068 PD3068 Datasheet Revision 62.0 53
Package Mechanical Drawings
The following table lists the supported devices for quad.
2.12.3 TQFP DimensionsThe following table lists the dimensions of thin quad flat pack (TQFP).
Table 40 • Supported Devices for Quad Slat (TQ/VQ)
Supported DevicesTQ64 TQ100 TQ144 TQ176 VQ80 VQ100 VQ128 VQ176 eX64eX128
APA075APA150A54SX08AA54SX16AA54SX32AeX64eX128eX256
A54SX08A54SX16PA54SX32A54SX08AA54SX16AA54SX32AAPA075A3P060A3P125A2F060M2S005M2GL005M2S010M2GL010
A1240AA1440AA1460AA14V40AA14V60AA1240XL*A1280XL*A1280XLV*A1240XLV*A3265DX*A32140DX*
A3265DXV*A32140DXV1
A42MX09A42MX16A42MX24A54SX08A54SX16A54SX16PA54SX32A54SX32A
1. This product is obsolete.
A1010BA10V10BA1020BA10V20BA40MX02A40MX04
A1225XL*A1415AA1425AA1440AA14V15AA14V25AA14V40AA42MX09A42MX16A54SX16
A54SX16PA54SX08AGL030AGL060AGL125AGL250AGLN030AGLN060AGLN125AGLN250A3P030A3P060A3P125A3P250M1A3P250A3P250LA3PN030A3PN060A3PN125A3PN250
AGLP030 AGLP060
Table 41 • TQFP Dimensions
JEDEC Equivalent
TQ64MS-026 VAR BCD
TQ100MS-026 VAR BED
TQ144MS-026 VAR BFB
TQ176MS-026 VAR BCA
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A – – 1.60 – – 1.60 – – 1.60 – – 1.60
A1 0.05 – 0.15 0.05 – 0.15 0.05 – 0.15 0.05 – 0.15
A2 1.35 1.40 1.45 1.35 1.40 1.45 1.35 1.40 1.45 1.35 1.40 1.45
b 0.17 0.22 0.27 0.17 0.22 0.27 0.17 0.22 0.27 0.17 0.22 0.27
c 0.09 – 0.20 0.09 – 0.20 0.09 – 0.20 0.09 – 0.20
D/E 12.00 BSC 16.00 BSC 22.00 BSC 26.00 BSC
D1/E1 10.00 BSC 14.00 BSC 20.00 BSC 24.00 BSC
e 0.50 BSC 0.50 BSC 0.50 BSC 0.50 BSC
L 0.45 0.60 0.75 0.45 0.60 0.75 0.45 0.60 0.75 0.45 0.60 0.75
ccc 0.08 0.08 0.08 0.10
Theta 0 3.50 deg
7 deg 0 3.50 deg
7 deg 0 3.50 deg
7 deg 0 3.50 deg
7 deg
5193068 PD3068 Datasheet Revision 62.0 54
Package Mechanical Drawings
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
2.12.4 VQFP DimensionsThe following table lists the dimensions of very thin quad flat pack (VQFP).
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
Note: Variation AEE plus 8 leads.
2.13 PBGAThe following figures show package outlines for various packages under PBGA.
2.13.1 BG272The following figure shows the package outline of BG272.
Table 42 • VQFP Dimensions
JEDECEquivalent
VQ80MS-026 VAR AEC
VQ100MS-026 VAR AED
VQ128MS-026 VAR AEE3
VQ176MS-026 VAR BFC
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A – – 1.20 – 1.20 – 1.20 – 1.20
A1 0.05 – 0.15 0.05 – 0.15 0.05 0.10 0.15 0.05 0.10 0.15
A2 0.95 1.00 1.05 0.95 1.00 1.05 0.95 1.00 1.05 0.95 1.00 1.05
b 0.22 0.32 0.38 0.17 0.22 0.27 0.13 0.18 0.23 0.13 0.18 0.23
c 0.09 – 0.20 0.09 – 0.20 0.09 – 0.20 0.09 – 0.20
D/E 16.00 BSC 16.00 BSC 16.00 BSC 22.00 BSC
D1/E1 14.00 BSC 14.00 BSC 14.00 BSC 20.00 BSC
e 0.65 BSC 0.50 BSC 0.40 BSC 0.40 BSC
L 0.45 0.60 0.75 0.45 0.60 0.75 0.45 0.60 0.75 0.45 0.60 0.75
ccc 0.10 0.08 0.08 0.08
Theta 0 3.50 deg
7 deg 0 3.50 deg
7 deg 0 3.50 deg
7 deg 0 3.50 deg
7 deg
5193068 PD3068 Datasheet Revision 62.0 55
Package Mechanical Drawings
Figure 37 • Package Outline of BG272
The following table shows the supported devices for BG272.
Note: This product is obsolete.
2.13.2 BG313The following figure shows the package outline of BG313.
Table 43 • Supported Devices for BG272
Supported DevicesA42MX36 A500K050*
A500K130*
D1/E1 SQ
Detail A
Side View
EE2
D
D2
Top View
R0.025 Typ.Detail A
30° A2
CA1
A
aaa C
E1
D1
Bottom View
e
1234567891011121314151617181920
A
YWVUTRPNMJKJHGFEDCB
// ccc C
// bbb C
e
A1 Ball Pad Corner A1 Ball Pad CornerAB
C
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 56
Package Mechanical Drawings
Figure 38 • Package Outline of BG313
Note: Dimensions are in millimeters. For more information on dimensions, see PBGA Dimensions, page 60.
The following table shows the supported devices for BG313.
2.13.3 BG329The following figure shows the package outline of BG329.
Table 44 • Supported Devices for BG313
Supported DevicesA14100AA14V100A
A54SX32
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30 A2
cA1
A
aaa C
// ccc C
// bbb C°
C
AB
Top View Bottom ViewA1 Ball Pad Corner
A1 Ball Pad Corner
1357911131519212325 17 246810121418202224 16
C
E
G
J
L
N
R
U
W
AA
AC
D
F
H
K
M
P
T
V
Y
AB
AD
B
AE
A
E2 E
D2
D
e
E1
D1e
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 57
Package Mechanical Drawings
Figure 39 • Package Outline of BG329
Note: Dimensions are in millimeters.For more information on dimensions, see PBGA Dimensions, page 60.
The following table shows the supported devices for BG329.
2.13.4 BG456The following figure shows the package outline of BG456.
Table 45 • Supported Devices for BG329
Supported DevicesA54SX32 A53SX32A
Bottom View
A1 Ball Pad Corner13579111315192123 17 2468101214182022 16
C
E
G
J
L
N
R
U
W
AA
AC
D
F
H
K
M
P
T
V
Y
AB
BA
e
E1
D1
e
E2 E
D2
D
Top ViewA1 Ball Pad Corner
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
AB
CNX Øb
Ø0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 58
Package Mechanical Drawings
Figure 40 • Package Outline of BG456
Note: Dimensions are in millimeters.For more information on dimensions, see PBGA Dimensions, page 60.
The following table shows the supported devices for BG456.
2.13.5 BG729The following figure shows the package outline of BG729.
Table 46 • Supported Devices for BG456
Supported DevicesA500K1301
A500K1801
A500K2701
1. This product is obsolete.
APA150APA300APA450APA600APA750APA1000
Top View Bottom View
A1 Ball Pad Corner
A1 Ball Pad Corner
E2 E
D2
D
e
E1
D1e
136810121416202426 18 2479111315192325 172221 5
D
F
H
K
M
P
T
V
Y
AD
AF
E
G
J
L
N
R
U
W
AC
AE
BA
C
ABAA
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
AB
CNX Øb
Ø0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 59
Package Mechanical Drawings
Figure 41 • Package Outline of BG729
Note: Dimensions are in millimeters.For more information on dimensions, see PBGA Dimensions, page 60.
The following table shows the supported devices for BG729.
2.13.6 PBGA DimensionsThe following table lists the dimensions of PBGA.
Table 47 • Supported Devices for BG729
Supported DevicesAX1000
Table 48 • PBGA Dimensions
JEDEC Equivalent
BG272MS-034 VAR BAL-2
BG313MS-034
BG329MS-034 VAR BAN-2
BG456MS-034 VAR BAR-2
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 2.18 2.33 2.50 2.12 2.33 2.52 2.17 2.33 2.70 2.12 2.33 2.54
A1 0.50 0.60 0.70 0.50 0.60 0.70 0.50 0.60 0.70 0.50 0.60 0.70
A2 1.15 1.17 1.19 1.12 1.17 1.22 1.10 1.20 1.30 1.12 1.17 1.19
aaa 0.20 0.20 0.20 0.20
b 0.60 0.75 0.90 0.60 0.76 0.90 0.60 0.76 0.90 0.60 0.76 0.90
bbb 0.25 0.25 0.25 0.25
c 0.53 0.56 0.61 0.53 0.56 0.61 0.53 0.60 0.70 0.51 0.56 0.61
ccc 0.35 0.35 0.35 0.35
D 26.80 27.00 27.20 34.80 35.00 35.20 30.80 31.00 31.20 34.80 35.00 35.20
A1 Ball Pad Corner
Top View Bottom ViewA1 Ball Pad Corner
E2 E
D2
D
E1
e
D1e
13681012141620242627 18 2479111315192325 172221 5
D
F
H
K
M
P
T
V
Y
AD
AFAG
E
G
J
L
N
R
U
W
AC
AE
BA
C
ABAA
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
AB
CNX Øb
Ø0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 60
Package Mechanical Drawings
2.14 FBGAThe following figures show package outlines for various packages under FBGA.
2.14.1 FG144The following figure shows the package outline of FG144.
D1 24.13 BSC 30.48 BSC 27.94 BSC 31.75 BSC
D2 23.90 24.00 24.10 29.50 30.00 30.70 27.90 28.00 28.10 29.80 30.00 30.20
E 26.80 27.00 27.20 34.80 35.00 35.20 30.80 31.00 31.20 34.80 35.00 35.20
E1 24.13 BSC 30.48 BSC 27.94 BSC 31.75 BSC
E2 23.90 24.00 24.10 29.50 30.00 30.70 27.90 28.00 28.10 29.80 30.00 30.20
e 1.27 typ. 1.27 typ. 1.27 typ. 1.27 typ.
JEDEC Equivalent
BG729MS-034 VAR BAR-1
Dimensions Min. Nom. Max.A 2.12 2.33 2.54
A1 0.50 0.60 0.70
A2 1.12 1.17 1.19
aaa 0.20
b 0.60 0.76 0.90
bbb 0.25
c 0.50 0.56 0.62
ccc 0.35
D 34.80 35.00 35.20
D1 33.02 BSC
D2 29.95 30.00 30.70
E 34.80 35.00 35.20
E1 33.02 BSC
E2 29.95 30.00 30.70
e 1.27 typ.
Table 48 • PBGA Dimensions
5193068 PD3068 Datasheet Revision 62.0 61
Package Mechanical Drawings
Figure 42 • Package Outline of FG144
Note: DimensionDimensions are in millimeters. For more information on dimensions, see Fine Pitch Plastic Ball Grid Array Dimensions, page 73.
The following table shows the supported devices for FG144.
2.14.2 FG256 MO-192 VAR DAF1The following figure shows the package outline of FG256 MO-192 VAR DAF1.
Table 49 • Supported Devices for FG144
Supported DevicesA54SX08 A500K0501
A500K130*
1. This product is obsolete.
APA075APA150APA300APA450
A54SX08AA54SX16AA54SX32A
AGL060AGL125AGL250AGL400AGL600AGL1000M1AGL250M1AGL600M1AGL1000
A3P060 A3P125A3P250A3P400A3P600A3P1000M1A3P250M1A3P400M1A3P600M1A3P1000M7A3P1000
A3P250LA3P600LA3P1000LM1A3P600L/M1A3P1000L
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
// bbb BA
C
A1
A2
Detail A
CNX Øb
Ø0.25 MØ0.10 M
CC
A B
D/D2
A1 BallPad Corner
E/E2
E/4
D/4A
B
C
D
E
F
G
H
J
K
L
M
123456789101112
e
eD1
E1
Top View Bottom ViewA1 Ball Pad CornerA
B
5193068 PD3068 Datasheet Revision 62.0 62
Package Mechanical Drawings
Figure 43 • Package Outline of FG256 MO-192 VAR DAF1
Note: Dimensions are in millimeters. For more information on dimensions, see Fine Pitch Plastic Ball Grid Array Dimensions, page 73.
The following table lists the supported devices for FG256 MO-192 VAR DAF1.
2.14.3 FG256 MS-034 VAR AAF-1The following figure shows the package outline of FG256 MS-034 VAR AAF-1.
Table 50 • Supported Devices for FG256 MO-192 VAR DAF1
Supported DevicesA500K1301
A500K180*A500K270*
1. This product is obsolete.
APA150APA300APA450APA600
A54SX16A AX125AX250
AGL400AGL600AGL1000M1AGL600M1AGL1000AGLE600
A3P250A3P400A3P600A3P1000M1A3P400M1A3P600M1A3P1000M7A3P1000A3PE600
A3P250LA3P600LA3P1000LM1A3P600LM1A3P1000L
AFS090AFS250AFS600AFS1500M1AFS250M1AFS600M1AFS1500M7AFS600
A2F060A2F200A2F500
NX ØbØ0.25 MØ0.10 M
CC
A B
E/4
D/4
A1 Ball Pad Corner A1 Ball Pad Corner
Top View Bottom View
13579111315 246810121416
D
e
E1E E2
D2 D1e
C
E
G
J
L
N
R
D
F
H
K
M
P
T
BA
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
// bbb BA
C
A1
A2
Detail A
AB
C
5193068 PD3068 Datasheet Revision 62.0 63
Package Mechanical Drawings
Figure 44 • Package Outline of FG256 MS-034 VAR AAF-1
Note: Dimensions are in millimeters. For more information on dimensions, see Fine Pitch Plastic Ball Grid Array Dimensions, page 73.
The following table lists the supported devices for FG256 MS-034 VAR AAF-1.
2.14.4 FG324The following figure shows the package outline of FG324.
Table 51 • Supported Devices for FG256 MS-034 VAR AAF-1
Supported DevicesA54SX32AA54SX72A
B
Top View Bottom ViewA1 Ball Pad Corner
E2E
13579111315 246810121416
C
E
G
J
L
N
R
D
F
H
K
M
P
T
BA
E1
D2
D
D1
e
e
A1 Ball Pad Corner
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
C
A
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 64
Package Mechanical Drawings
Figure 45 • Package Outline of FG324
Note: Dimensions are in millimeters. For more information on dimensions, see Fine Pitch Plastic Ball Grid Array Dimensions, page 73.
The following table lists the supported devices for FG324.
2.14.5 FG484 MS-034 VAR AAL-1The following figure shows the package outline of FG484 MS-034 VAR AAL-1.
Table 52 • Supported Devices for FG324
Supported DevicesAX125 A3PE3000
M1A3PE3000A3PE3000LM1A3PE3000L
Bottom ViewTop View
13579111315 2468101214D
E
D2
E2
16
C
E
G
J
L
N
R
D
F
H
K
M
P
T
BA
1718
UV
A1 Ball Pad Corner
e
E1
D1e
E/4
D/4
A1 Ball Pad CornerA
B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
// bbb BA
C
A1
A2
Detail A
C
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 65
Package Mechanical Drawings
Figure 46 • Package Outline of FG484 MS-034 VAR AAL-1
Note: Dimensions are in millimeters. For more information on dimensions, see Fine Pitch Plastic Ball Grid Array Dimensions, page 73.
The following table lists the supported devices for FG484 MS-034 VAR AAL-1.
2.14.6 FG484—Fully Populated MS-034 VAR AAJ-1The following figure shows the package outline of FG484 Fully Populated MS-034 VAR AAJ-1.
Table 53 • Supported Devices for FG484 MS-034 VAR AAL-1
Supported DevicesA54SX32AA54SX72A
Top View Bottom View
D
D2A1 Ball Pad Corner
A1 Ball Pad Corner
E2E
ABCDEFGHJKLMNPRTUVWYAAABACADAEAF
1234567891011121314151617181920212223242526
E1
e
eD1
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
C
A
B
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 66
Package Mechanical Drawings
Figure 47 • Package Outline of FG484—Fully Populated MS-034 VAR AAJ-1
Note: Dimensions are in millimeters. For more information on dimensions, see Fine Pitch Plastic Ball Grid Array Dimensions, page 73.
The following table lists the supported devices for FG484—Fully Populated MS-034 VAR AAJ-1.
2.14.7 FG676 (Option 1)The following figure shows the package outline of FG676 (Option 1).
Table 54 • Supported Devices for FG484—Fully Populated MS-034 VAR AAJ-1
Supported DevicesAPA450APA600
AX250AX500AX1000
AGL400AGL600AGL1000M1AGL600M1AGL1000AGLE600AGLE3000M1AGLE3000
A3P400A3P600A3P1000M1A3P400M1A3P600M1A3P1000M7A3P1000
A3PE600A3PE1500A3PE3000M1A3PE1500M1A3PE3000A3PE600LA3PE3000LM1A3PE3000L
A3P600LA3P1000LM1A3P600LM1A3P1000L
AFS600AFS1500M1AFS600M1AFS1500M7AFS600
A2F200A2F500
Top View Bottom View
D
D2
E2E
A1 Ball Pad CornerA1 Ball Pad Corner
ABCDEFGHJKLMNPRTUVWYAAAB
12345678910111213141516171819202122
E1
e
D1
e
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
C
A
B
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 67
Package Mechanical Drawings
Figure 48 • Package Outline of FG676 (Option 1)
Note: Dimensions are in millimeters. For more information on dimensions, see FG676 (Option 1 and 2) Package Mechanical Drawing Dimensions, page 69.
The following table lists the supported devices for FG676 (Option 1).
2.14.8 FG676 (Option 2)The following figure shows the package outline of FG676 (Option 2).
Table 55 • Supported Devices for FG676 (Option 1)
Supported DevicesA500K2701 APA600
APA750AX500AX1000
A3PE1500M1A3PE1500
AFS1500M1AFS1500
Top View Bottom View
D
D2
E2E
A1 Ball Pad Corner A1 Ball Pad Corner
ABCDEFGHJKLMNPRTUVWYAAABACADAEAF
1234567891011121314151617181920212223242526
E1
e
eD1
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
C
A
B
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 68
Package Mechanical Drawings
Figure 49 • Package Outline of FG676 (Option 2)
Note: Dimensions are in millimeters. For more information on dimensions, see FG676 (Option 1 and 2) Package Mechanical Drawing Dimensions, page 69.
The following table lists the supported devices for FG676 (Option 2).
2.14.9 FG676 (Option 1 and 2) Package Mechanical Drawing DimensionsThe following table lists the dimensions of FG676 (Option 1 and 2) Package Mechanical Drawing.
Table 56 • Supported Devices for FG676 (Option 2)
Supported DevicesSmartFusion®2 (M2S090, M2S060) IGLOO®2 (M2GL090, M2GL060)
Table 57 • Dimensions of FG676 (Option 1 and 2) Package Mechanical Drawing
JEDEC Equivalent
FG676 (Option 1), page 6727mm X 27mm, 1.0mm Pitch, 676 SolderBalls, PBGA
FG676 (Option 2), page 6827mm X 27mm, 1.0mm Pitch, 676 SolderBalls, PBGA
Dimension Min. Nom. Max. Min. Nom. Max.A 2.02 2.23 2.44 2.02 2.23 2.44
A1 0.40 0.50 0.60 0.40 0.50 0.60
A2 1.12 1.17 1.22 1.12 1.17 1.22
aaa 0.20 0.15
b 0.50 0.63 0.70 0.50 0.61 0.70
Gate Protrusion
Gate Chip Out
Scale: None(X-Section View)
1.0±0.1
(0.05)
Top View
A1 Ball Pad Corner
Dimple by Mold
1.0
D
D2
AB
0.20A B
+
Detail B
4.00
E2 E
Bottom View
M
M
b
0.25
0.10
C
C
A B
aaa
bbbccc
C
C
C
C
30° Typ.
AA2B
Side ViewDetail B
1234567891011121314151617181920212223242526
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
A1 Ball Pad Corner
E1
e
e
D1
5193068 PD3068 Datasheet Revision 62.0 69
Package Mechanical Drawings
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
2.14.10 FG484—Fully Populated MS-034 VAR AAJ-1, Larger Mold Cap SizeThe following figure shows package outlines of FG484 Fully Populated MS-034 VAR AAJ-1, larger mold cap size.
Figure 50 • Package Outline of FG484 MS-034 VAR AAJ-1
bbb 0.25 0.25
c 0.50 0.56 0.62 0.50 0.56 0.62
ccc 0.35 0.35
D 26.80 27.00 27.20 26.80 27.00 27.20
D1 25.00 BSC 25.00 BSC
D2 23.95 24.00 24.70 25.65 25.70 26.05
E 26.80 27.00 27.20 26.80 27.00 27.20
E1 25.00 BSC 25.00 BSC
E2 23.95 24.00 24.70 25.65 25.70 26.05
e 1.00 typ. 1.00 typ.
Table 57 • Dimensions of FG676 (Option 1 and 2) Package Mechanical Drawing
A
A
B
B
22 2120191817 161514 1312 11 10 9 8 7 6 5 4 3 2 1
ABCDEFGHJKLMNPRTUVWYAAAB
e
e
D
D1
D2
Detail A
Dimple by Mold1.0
0.20
4.0
A1 Ball Pad Corner
+
Top View Bottom View
4 × 9.00
E E1E2
A1 Ball Pad Corner
D1/E1 SQ
Detail B
Side ViewR0.025 Typ.
Detail BDetail A
30° A2
cA1
A
aaa C
// ccc C// bbb C
CNX ØbØ0.25 MØ0.10 M
CC
A B
Gate Protrusion
Gate Chip Out
(0.05)
1.0 + 0.1
5193068 PD3068 Datasheet Revision 62.0 70
Package Mechanical Drawings
The following table lists the supported devices for FG484 MS-034 VAR AAJ-1.
2.14.11 FG896The following figure shows package outlines of FG896.
Figure 51 • Package Outline of FG896
The following table lists the supported devices for FG896.
2.14.12 FG896—Larger Mold Cap SizeThe following figure shows the package outline of larger mold cap size for FG896.
Table 58 • Supported Devices for FG484 MS-034 VAR AAJ-1
Supported DevicesM2S005, M2S005SM2S010, M2S010T, M2S010TSM2S025, M2S025T, M2S025TSM2S050, M2S050T, M2S050TSM2S090, M2S090T, M2S090TSM2S060, M2S060T, M2S060TS
M2GL005, M2GL005SM2GL010, M2GL010T, M2GL010TSM2GL025, M2GL025T, M2GL025TSM2GL050, M2GL050T, M2GL050TSM2GL090, M2GL090T, M2GL090TSM2GL060, M2GL060T, M2GL060TS
Table 59 • Supported Devices for FG896
Supported DevicesM2S050, M2S050S, M2S050TS M2GL050, M2GL050S, M2GL050TS
D1
E2E
D
D2
Top View Bottom View
123456789101112131415161718192021222324252627282930
ABCDEFGHJKLMNPRTUVWYAAABACADAEAFAGAHAJAK
E1
e
e
A1 Ball Pad Corner
A1 BallPad Corner
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
CNX Øb
Ø0.25 MØ0.10 M
CC
A B
A
B
5193068 PD3068 Datasheet Revision 62.0 71
Package Mechanical Drawings
Figure 52 • Package Outline of FG896 Larger Mold Cap Size
The following table lists the supported devices for FG896 larger mold cap size.
2.14.13 FG1152The following figure shows the package outline of FG1152.
Table 60 • Supported Devices for FG896 Larger Mold Cap Size
Supported DevicesM2S050, M2S050S, M2S050TS M2GL050, M2GL050S, M2GL050TS
1234567891011121314151 61718192021222324252627282930
ABCDEFGHJKLMNPRTUVWYAAABACADAEAFAGAHAJAK
A1 Ball Pad Corner
D1/E1 SQ
Detail B
Side ViewR0.025 Typ.
Detail B
30° A2
cA1
A
aaa C
// ccc C// bbb C
CNX Øb
Ø0.25 MØ0.10 M
CC
A B
Top View Bottom View
A1 Ball Pad Corner
Dimple by Mold1.0
D
D2
D1
AB
0.20A B
+
Detail A
4.00
E2 E1E
e
Detail A
Gate Protrusion
Gate Chip Out
(0.05)
1.0 + 0.1
e
Note: The dimple in the center is the mold gate.
5193068 PD3068 Datasheet Revision 62.0 72
Package Mechanical Drawings
Figure 53 • Package Outline of FG1152
Note: Dimensions are in millimeters. For more information on dimensions, see Fine Pitch Plastic Ball Grid Array Dimensions, page 73.
The following table lists the supported devices for FG1152.
2.14.14 Fine Pitch Plastic Ball Grid Array DimensionsThe following table lists the details and dimensions for FG144, FG256, and FG324.
Table 61 • Supported Devices for FG1152
Supported DevicesAPA1000 AX2000
Table 62 • Fine Pitch Plastic Ball Grid Array Dimensions for FG144, FG256, and FG324
JEDECEquivalent
FG144, page 61 MO-192 VAR DAD-1
FG256 MO-192 VAR DAF1, page 62MO-192 VAR DAF1
FG256 MS-034 VAR AAF-1, page 63MS-034 VAR AAF-1
FG324, page 64MS-034 VAR AAG-1
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 1.35 1.45 1.55 1.35 1.60 1.70 1.55 1.76 1.97 1.48 1.63 1.78
A1 0.35 0.40 0.45 0.25 0.40 – 0.30 0.40 0.50 0.33 0.38 0.43
A2 0.65 0.70 0.75 0.65 0.70 0.75 0.75 0.80 0.85 0.65 0.70 0.75
aaa 0.10 0.12 0.20 0.20
b 0.45 0.50 0.55 0.45 0.50 0.55 0.40 0.50 0.60 0.49 0.54 0.59
bbb 0.25 0.25 0.25 0.25
c – 0.35 – 0.40 0.50 0.60 0.50 0.56 0.62 0.50 0.55 0.60
ccc 0.35 0.35 0.35 0.35
D 12.80 13.00 13.20 16.80 17.00 17.20 16.80 17.00 17.20 18.80 19.00 19.20
Top View Bottom View
BC
EF
J
L
PRT
12345678910111213141516171819202122232425262728293031323334
A
D
GH
K
MN
UVWYAAABACADAEAFAGAHAJ
AP
AKALAMAN
D1/E1 SQ
Detail A
Side ViewR0.025 Typ.
Detail A
30° A2
cA1
A
aaa C
// ccc C
// bbb C
C
A1 Ball Pad Corner
A1 BallPad Corner D
D2
E2E E1
e
eD1
A
B
NX ØbØ0.25 MØ0.10 M
CC
A B
5193068 PD3068 Datasheet Revision 62.0 73
Package Mechanical Drawings
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
The following table lists the details and dimensions for FG484.
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
D1 11.00 BSC 15.00 BSC 15.00 BSC 17.00 BSC
D2 12.80 13.00 13.20 16.80 17.00 17.20 14.80 15.00 15.20 18.80 19.00 19.20
E 12.80 13.00 13.20 16.80 17.00 17.20 16.80 17.00 17.20 18.80 19.00 19.20
E1 11.00 BSC 15.00 BSC 15.00 BSC 17.00 BSC
E2 12.80 13.00 13.20 16.80 17.00 17.20 14.80 15.00 15.20 18.80 19.00 19.20
e 1.00 typ. 1.00 typ. 1.00 typ. 1.00 typ.
Table 63 • Fine Pitch Plastic Ball Grid Array Dimensions for FG484
JEDEC Equivalent
FG484 MS-034 VAR AAL-1, page 65 MS-034 VAR AAL-1
FG484—Fully Populated MS-034 VAR AAJ-1, page 66 (23x23 Fully Populated)MS-034 VAR AAJ-1
FG484—Fully Populated MS-034 VAR AAJ-1, Larger Mold Cap Size, page 70 (23x23 Fully PopulatedMS-034 VAR AAJ-1with Larger Mold Cap
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 2.02 2.23 2.44 2.02 2.23 2.44 2.02 2.23 2.44
A1 0.40 0.50 0.60 0.40 0.50 0.60 .040 .050 .060
A2 1.12 1.17 1.22 1.12 1.17 1.22 1.12 1.17 1.22
aaa 0.20 0.20 0.15
b 0.50 0.63 0.70 0.50 0.63 0.70 0.50 0.61 0.70
bbb 0.25 0.25 0.25
c 0.50 0.56 0.62 0.50 0.56 0.62 0.50 0.56 0.62
ccc 0.35 0.35 0.35
D 26.80 27.00 27.20 22.80 23.00 23.20 22.80 23.00 23.20
D1 25.00 BSC 21.00 BSC 21.00 BSC
D2 23.80 24.00 24.20 19.45 19.50 20.20 22.35 22.40 22.75
E 26.80 27.00 27.20 22.80 23.00 23.20 22.80 23.00 23.20
E1 25.00 BSC 21.00 BSC 21.00 BSC
E2 23.80 24.00 24.20 19.45 19.50 20.20 22.35 22.40 22.75
e 1.00 typ. 1.00 typ. 1.00 typ.
Table 62 • Fine Pitch Plastic Ball Grid Array Dimensions for FG144, FG256, and FG324
5193068 PD3068 Datasheet Revision 62.0 74
Package Mechanical Drawings
The following table lists the details and dimensions for FG896 and FG1152.
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
2.14.15 FC1152The following figure shows the package outline of FC1152.
Table 64 • Fine Pitch Plastic Ball Grid Array Dimensions for FG896 and FG1152
JEDECEquivalent
FG896, page 71 MS-034 VAR AAN-1
FG896, page 71 MS-034 VAR AAN-1 with Larger Mold Cap
FG1152, page 72 MS-034 VAR AAR-1
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 2.02 2.23 2.44 2.02 2.23 2.44 2.02 2.23 2.44
A1 0.40 0.50 0.60 0.40 0.50 0.60 0.40 0.50 0.60
A2 1.12 1.17 1.22 1.12 1.17 1.22 1.12 1.17 1.22
aaa 0.20 0.15 0.20
b 0.50 0.63 0.70 0.50 0.61 0.70 0.50 0.63 0.70
bbb 0.25 0.25 0.25
c 0.50 0.56 0.62 0.50 0.56 0.62 0.50 0.56 0.62
ccc 0.35 0.35 0.35
D 30.80 31.00 31.20 30.80 31.00 31.20 34.80 35.00 35.20
D1 29.00 BSC 29.00 BSC 33.00 BSC
D2 (option 1)1
1. As per JEDEC specification MS-034, a different lid size is allowed (D2/E2) for FG896.
25.95 26.00 26.70 29.65 29.70 30.05 33.65 33.70 34.20
D2 (option 2)3 28.80 29.00 29.20
E 30.80 31.00 31.20 30.80 31.00 31.20 34.80 35.00 35.20
E1 29.00 BSC 29.00 BSC 33.00 BSC
E2 (option 1)3 25.95 26.00 26.70 29.65 29.70 30.05 33.65 33.70 34.20
E2 (option 2)3 28.80 29.00 29.20
e 1.00 typ. 1.00 typ. 1.00 typ.
5193068 PD3068 Datasheet Revision 62.0 75
Package Mechanical Drawings
Figure 54 • Package Outline of FC1152
The following table lists the supported devices for FC1152.
2.14.16 FCV484The following figure shows the package outline of FCV484.
Table 65 • Supported Devices for FC1152
Supported DevicesSmartFusion®2 (M2S150) IGLOO®2 (M2GL150)
A1 Ballpad
Corner
Optional
Pin 1 ID
A
B
Top View
3.00 TYP.
(2 Places)
4X R0.5 - 1.25 3.00 TYP.
(2 Places)
4X R0.5
No CHAMFER
1.00
1.00
A1 Ballpad Corner
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
2728
2930
3132
3334
ABCDEFGHJKLMN
PRTUVWYAAABACADAEAFAGAHAJAKALAMANAP
Bottom View1152 Solder Balls
29.0
35.0
1.00
1.00
35.029.0
M
M
0.64 + 0.06/-0.14
0.25
0.10
C
C
A B
2.62±0.28
(1.30)
0.5 ±0.1
27.0
0.25
0.20
C
C C
Side View
0.72
Seating Plane
0.50
CU0.15 0.10
5193068 PD3068 Datasheet Revision 62.0 76
Package Mechanical Drawings
Figure 55 • Package Outline of FCV484
Note: Dimensions are in millimeters. For more information on dimensions, see FCV484 Package Mechanical Drawing Dimensions, page 77.
The following table lists the supported devices for supported devices for FCV484.
2.14.17 FCV484 Package Mechanical Drawing DimensionsThe following table shows the details and dimensions of FCV484 package mechanical drawing.
Table 66 • Supported Devices for FCV484
Supported DevicesSmartFusion 2 (M2S150) IGLOO 2 (M2GL150)
Table 67 • FCV484 Package Mechanical Drawing Dimensions
JEDECEquivalent FCV484, page 76Dimension Min. Nom. Max.A 2.85 3.00 3.15
A1 0.30 0.40 0.50
A2 0.50
aaa 0.20
b 0.45 0.50 0.55
ccc 0.25
D 19.00
D1 16.80 BSC
D2 18.00 REF
B
SEATING PLANE
eee M
fff M
b
C
C A B
aaa C
C
ccc C
Top View
484 SOLDER BALLS
Bottom View
(1.10)
(1.10)
e
D1
E1
22 20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
A
C
E
G
J
L
N
R
U
W
AA
B
D
F
H
K
M
P
T
V
Y
AB
A1 BALLPAD
CORNER
D
0.15 U 0.10 C
D2
E2
A
ddd C (3X)
E
E3/D3
A1
A2
c
A
Side View
A1 BALL PAD CORNER
e
5193068 PD3068 Datasheet Revision 62.0 77
Package Mechanical Drawings
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
2.14.18 FC1152 Package Mechanical Drawing DimensionsThe following table shows the dimensions of FC1152.
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
2.15 Chip Scale Package (UC/CS/VF)The following figures show package outlines for various packages under chip scale package.
D3 18.00 REF
E 19.00
E1 16.80 BSC
E2 18.00 REF
E3 18.00 REF
e .80 BSC
eee 0.15
fff 0.08
Table 68 • Dimensions of FC1152
JEDECEquivalent FC1152, page 75Dimension Min. Nom. Max.A 2.34 2.62 2.90
A1 0.40 0.50 0.60
A2 0.8
aaa 0.20
b 0.50 0.64 0.70
ccc 0.25
D 34.85 35.00 35.15
D1 33.00 BSC
D2 29.00 REF
D3 27.00 REF
E 34.85 35.00 35.15
E1 33.00 BSC
E2 29.00 REF
E3 27.00 REF
e 1.00 BSC
eee 0.25
fff 0.10
Table 67 • FCV484 Package Mechanical Drawing Dimensions
5193068 PD3068 Datasheet Revision 62.0 78
Package Mechanical Drawings
2.15.1 UC36The following figure shows the package outline of UC36.
Figure 56 • Package Outline of UC36
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for UC36.
2.15.2 CS49The following figure shows the package outline of CS49.
Table 69 • Supported Devices for UC36
Supported DevicesAGLN010
B
D
D/2
E/2
E
A
6 5 4 3 2 1
ABCDEF
Top View
e
(0.5)
(0.5)
e
Bottom View
A1 Ball Pad Corner
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
5193068 PD3068 Datasheet Revision 62.0 79
Package Mechanical Drawings
Figure 57 • Package Outline of CS49
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS49.
2.15.3 UC81The following figure shows the package outline of UC81.
Table 70 • Supported Devices for CS49
Supported DeviceseX641
eX1281
1. This product is obsolete.
e
1234567
A
B
C
D
E
F
G
D1
e
E1
D/D2
E/E2
E/4
D/4
A1 Ball Pad CornerA1 Ball Pad Corner
ddd(4X)
Top View Bottom View
Side View Detail A
AB
D1/E1 SQ
Detail A
eee C
fff CA B
// ccc C
aaa C
A
C
A1
A2
NX ØbC
5193068 PD3068 Datasheet Revision 62.0 80
Package Mechanical Drawings
Figure 58 • Package Outline of UC81
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for UC81.
2.15.4 CS81The following figure shows the package outline of CS81.
Table 71 • Supported Devices for UC81
Supported DevicesAGL030 AGLN020
AGLN030
Pin A1Pad Corner
Top View Bottom View
Pin A1Pad Corner
81 Metal Lands
E
D
0.10 (4X)
e
e
(0.40)
(0.40)
9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
B
A
5193068 PD3068 Datasheet Revision 62.0 81
Package Mechanical Drawings
Figure 59 • Package Outline of CS81
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS81.
2.15.5 CS121The following figure shows the package outline of CS121.
Table 72 • Supported Devices for CS81
Supported DevicesAGL030AGL250
AGLN020AGLN030AGLN060AGLN125AGLN250
B
A
Pin A1Pad Corner
Top View Bottom View
Pin A1Pad Corner
81 Metal Lands
E
D
0.10 (4X)
e
e
(0.50)
(0.50)
9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
5193068 PD3068 Datasheet Revision 62.0 82
Package Mechanical Drawings
Figure 60 • Package Outline of CS121
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS121.
2.15.6 CS128The following figure shows the package outline of CS128.
Table 73 • Supported Devices for CS121
Supported DevicesAGL060
0.10 (4X)
B
AA1 Ball PadCorner
Top View Bottom View121 Solder Balls
E
D
e
e
(0.50)
(0.50)
A1 Ball Pad Corner
1110 9 8 7 6 5 4 3 2 1
ABCDEFGHJKL
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
5193068 PD3068 Datasheet Revision 62.0 83
Package Mechanical Drawings
Figure 61 • Package Outline of CS128
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS128.
2.15.7 CS180 The following figure shows the package outline of CS180.
Table 74 • Supported Devices for CS128
Supported DeviceseX641
eX1281
eX2561
1. This product is obsolete
101112
E1
D1
D/D2
E/E2
E/4
D/4
Top View Bottom ViewA1 Ball Pad Corner
A1 Ball Pad Corner
ddd (4X)
9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
e
e
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
AB
5193068 PD3068 Datasheet Revision 62.0 84
Package Mechanical Drawings
Figure 62 • Package Outline of CS180
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS180.
2.15.8 CS196The following figure shows the package outline of CS196.
Table 75 • Supported Devices for CS180
Supported DeviceseX2561
1. This product is obsolete.
AX1251
E1
e
eD1
D/D2
E/E2
E/4
D/4
Top View Bottom ViewA1 Ball Pad Corner
A1 Ball Pad Corner
ddd(4X)
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
AB
1011121314 9 8 7 6 5 4 3 2 1
A
B
CDEFGHJKLMN P
5193068 PD3068 Datasheet Revision 62.0 85
Package Mechanical Drawings
Figure 63 • Package Outline of CS195
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS196.
2.15.9 CS201The following figure shows the package outline of CS201.
Table 76 • Supported Devices for CS196
Supported DevicesAGL125AGL250AGL400
E1
e
eD1
D/D2
E/E2
E/4
D/4
Top View Bottom ViewA1 Ball Pad Corner
A1 Ball Pad Corner
ddd(4X)
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
AB
1011121314 9 8 7 6 5 4 3 2 1
A
B
CDEFGHJKLMN P
5193068 PD3068 Datasheet Revision 62.0 86
Package Mechanical Drawings
Figure 64 • Package Outline of CS201
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS201.
2.15.10 FCS325–(Option 1)The following figure shows the package outline of FCS325 (Option 1).
Table 77 • Supported Devices for CS201
Supported DevicesAGLP030AGLP060
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
2345678915 14 13 12 11 10
0.10 (4X)
A
B
Top View Bottom View201 Solder Balls
E
D
e(0.50)
(0.50)
e
A1 Ball Pad Corner
ddd (4X)
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Øb
Detail A
C
5193068 PD3068 Datasheet Revision 62.0 87
Package Mechanical Drawings
Figure 65 • Package Outline of FCS325 (Option 1)
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for FCS325–(Option 1).
2.15.11 FCS325–(Option 2)The following figure shows the package outline of FCS325–(Option 2).
Table 78 • Supported Devices for FCS325 (Option 1)
Supported DevicesSmartFusion2 (M2S050, M2S025,M2S060)
IGLOO2 (M2GL050, M2GL025, M2GL060)
aaaA A1
SEATING PLANE
A2
C C
ccc C
Side View
eee M
fff M
b
C
C A B
20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
AB
C
D
E
F
G
H
J
K
LM
P
R
U
V
AA
W
Y
T
N
(0.500)
(0.500)
E
D
E1
D1
325 SOLDER BALLS
A1 BALL PAD CORNER
B
A
(2X)
(2X)
ddd C
ddd C
TERMINAL A1 CORNER
INDEX AREA
e
eTop View
Bottom View
5193068 PD3068 Datasheet Revision 62.0 88
Package Mechanical Drawings
Figure 66 • Package Outline of FCS325–(Option 2)
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for FCS325–(Option 2).
2.15.12 CS281The following figure shows the package outline of CS281.
Table 79 • Supported Devices for FCS325 (Option 2)
Supported DevicesSmartFusion2 (M2S090) IGLOO2 (M2GL090)
Bottom View
A1 Ball Pad Corner
325 SOLDER BALLS
Top View
Side View
ddd
ddd
e
e
20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
AB
C
D
E
F
G
H
J
K
LM
P
R
U
V
AA
W
Y
T
N
aaa
eee
fff
SEATING PLANE
ccc
A A1
A2
b
D
B
A
D1
TERMINAL A1 CORNER
INDEX AREA
E
(2X)
(2X)
C
C
C A B
C
C
E1
(0.500)
(1.750)
5193068 PD3068 Datasheet Revision 62.0 89
Package Mechanical Drawings
Figure 67 • Package Outline of CS281
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS281.
2.15.13 CS288The following figure shows the package outline of CS288.
Table 80 • Supported Devices for CS281
Supported DevicesAGLP125AGL600AGL1000M1AGL600M1AGL1000
Top View Bottom View
A1 Ball Pad Corner
10 9 8 7 6 5 4 3 2 1111213141516171819
MNPRTUV W
DEF
ABC
GHJ
K L
E
D D1
e
e
E1
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX ØbC
AB
ddd (4X)
Detail A
5193068 PD3068 Datasheet Revision 62.0 90
Package Mechanical Drawings
Figure 68 • Package Outline of CS288
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS288.
2.15.14 FCS536The following figure shows the package outline of FCS536.
Table 81 • Supported Devices for CS288
Supported DevicesA2F060A2F200A2F500
e
e
Top View Bottom View
21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A B C D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
E A
B
D
E1
D1
A1 Ball Pad Corner
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX ØbC
Detail A
5193068 PD3068 Datasheet Revision 62.0 91
Package Mechanical Drawings
Figure 69 • Package Outline of FCS536
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for FCS536.
2.15.15 CS289The following figure shows the package outline of CS289.
Table 82 • Supported Devices for FCS536
Supported DevicesIGLOO2 (M2GL150)
TERMINAL A1 CORNER
INDEX AREA
E
ddd C
ddd C
D
Top View
29 27 25 23 21 19 17 15 13 11 9 7 5 3 1
30 28 26 24 22 20 18 16 14 12 10 8 6 4 2
A
C
E
G
J
L
N
R
U
W
AA
AC
AE
AG
AJ
B
D
F
H
K
M
P
T
V
Y
AB
AD
AF
AH
AK
536 SOLDER BALLS
Bottom View
A1 BALL PAD CORNER
e
e(0.750)
(0.750)
D1
E1
Side View
A2
A1
c
A
eee M
fff M
b
C
C A B
aaa C
ccc C
C
SEATING PLANE
5193068 PD3068 Datasheet Revision 62.0 92
Package Mechanical Drawings
Figure 70 • Package Outline of CS289
Note: Dimensions are in millimeters. For more information on dimensions, see Chip Scale Package Dimensions, page 93.
The following table shows the supported devices for CS289.
2.15.16 Chip Scale Package DimensionsThe following table lists the chip scale package dimensions for UC36, CS49, UC81, and CS81.
Table 83 • Supported Devices for CS289
Supported DevicesAGLP030AGLP060AGLP125
Table 84 • Chip Scale Package Dimensions for UC36, CS49, UC81, and CS81
JEDEC Equivalent UC36, page 79
CS49, page 79MO-205 UC81, page 80 CS81, page 81
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 0.66 0.73 0.80 – – 1.50 0.66 0.73 0.80 0.66 0.73 0.80
A1 0.07 REF 0.25 – – 0.07 REF 0.07 REF
A2 0.40 0.45 0.50 0.85 – – 0.42 0.45 0.48 0.42 0.45 0.48
aaa 0.08 0.12 0.08 0.08
b 0.18 0.23 0.28 0.45 0.50 0.55 0.18 0.23 0.28 0.20 0.25 0.30
c 0.21 REF – 0.36 – 0.21 REF 0.21 REF
ccc 0.10 0.10 0.10 0.10
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX ØbC
BE
D
A
ddd (4X)
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
ABCDEFGHJKLMNPRTU
E1
Top View Bottom View
A1 Ball Pad Corner
D1
e
e
Detail A
5193068 PD3068 Datasheet Revision 62.0 93
Package Mechanical Drawings
The following table lists the chip scale package dimensions for CS121, CS128, CS180, CS196, and CS201.
Note: All dimensions are in millimeters.
Note: Variation AG depopulated.
The following table lists the chip scale package dimensions for FC325 and FC536.
D/E 3.00 BSC 7.00 BSC 4.00 BSC 5.00 BSC
D1/E1 2.00 – 4.80 – – 3.20 – – 4.00 –
e 0.4 BSC 0.8 BSC 0.4 BSC 0.5 BSC
eee 0.15 0.15 0.15 0.15
fff 0.05 0.08 0.05 0.05
Table 85 • Chip Scale Package Dimensions for CS121, CS128, CS180, CS196, and CS201
JEDEC Equivalent
CS121, page 82MO-195, Variation AC
CS128, page 83MO-205, Variation BD
CS180, page 84MO-205, Variation BF
CS196, page 85MO-195, Variation BE
CS201, page 86MO195, Variation AE2
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min.Nom. Max.
A 0.79 0.89 0.99 – – 1.50 – – 1.50 – – 1.20 0.79 0.89 0.99
A1 0.18 0.23 0.28 0.25 – – 0.25 – - 0.15 – – 0.18 0.23 0.28
A2 0.40 0.45 0.50 0.85 – – 0.85 – - 0.60 – – 0.40 0.45 0.50
aaa 0.08 0.12 0.12 0.08 0.08
b 0.25 0.30 0.35 0.45 0.50 0.55 0.45 0.50 0.55 0.25 0.30 0.35 0.25 0.30 0.35
c 0.16 0.21 0.26 – 0.36 – – 0.36 – – 0.36 – 0.16 0.21 0.25
ccc 0.10 0.10 0.10 0.10 0.10
D/E 6.00 BSC 11.00 BSC 13.00 BSC 8.00 BSC 8.00 BSC
D1/E1 – 5.00 – – 8.80 – – 10.40 – – 6.50 – – 7.00 –
e 0.5 BSC 0.8 BSC 0.8 BSC 0.5 BSC 0.5 BSC
eee 0.15 0.15 0.15 0.15 0.15
fff 0.05 0.08 0.08 0.05 0.05
Table 86 • Chip Scale Package Dimensions for FC325 and FC536
JEDECEquivalent
CS325 (Option 1)(FCS325–(Option 1), page 87) FCS325–(Option 2), page 88 FCS536, page 91
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A 1.01 1.16 1.45
A1 0.15 0.21 0.15 0.21 0.15 0.24
A2 0.40 0.45 0.50 0.55 0.60 0.65 0.55 0.60 0.65
aaa 0.08 0.08 0.08
b 0.25 0.30 0.35 0.25 0.30 0.35 0.25 0.30 0.35
bbb N.A. N.A. N.A.
Table 84 • Chip Scale Package Dimensions for UC36, CS49, UC81, and CS81
5193068 PD3068 Datasheet Revision 62.0 94
Package Mechanical Drawings
Note: All dimensions are in millimeters.
Note: Variation AG depopulated.
The following table lists the chip scale package dimensions for CS281, CS288, and CS289
Note: All dimensions are in millimeters.
Note: Variation AG depopulated.
2.15.17 VF256The following figure shows the package outline of VF256.
c 0.21 0.25 0.29 0.21 0.25 0.29 0.472 0.512 0.552ccc 0.10 0.10 0.10
D 11.00 13.50 16.0
D1 10.00 BSC 10.00 BSC 14.50 BSC
E 11.00 11.00 16.0
ddd 0.15 0.15 0.15
E1 10.00 BSC 10.00 BSC 14.50 BSC
e 0.50 TYP 0.50 TYP 0.50 TYP
eee 0.15 0.15 0.15
Table 87 • Chip Scale Package Dimensions for FC325 and FC536
JEDEC Equivalent
CS281, page 89MO-195, Variation AG2 CS288, page 90 CS289, page 92
Dimension Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.A – – 1.05 – – 1.05 1.01 1.11 1.20
A1 0.18 0.23 0.28 0.18 0.23 0.28 0.25 0.30 0.35
A2 – 0.45 REF – – 0.45 REF – 0.55 0.60 0.65
aaa 0.08 0.08 0.08
b 0.26 0.31 0.36 0.26 0.31 0.36 0.35 0.40 0.45
c – 0.26 REF – – 0.26 REF – 0.17 0.21 0.25
ccc 0.20 0.20 0.10
D/E 9.85 10.00 10.15 10.85 11.0 11.15 14.00 BSC
D1/E1 9.00 BSC 10.00 BSC – 12.80 –
e 0.5 BSC 0.5 BSC 0.8 BSC
eee 0.15 0.15 0.15
fff 0.05 0.05 0.08
Table 86 • Chip Scale Package Dimensions for FC325 and FC536
5193068 PD3068 Datasheet Revision 62.0 95
Package Mechanical Drawings
Figure 71 • Package Outline of VF256
Note: Dimensions are in millimeters. For more information on dimensions, see Dimensions of VF256, page 98.
The following table shows the supported devices for VF256.
2.16 Very Fine Pitch Ball Grid ArrayThe following figures show package outlines for various packages under very fine pitch ball grid array.
2.16.1 VF400The following figure shows the package outline of VF400.
Table 88 • Supported Devices for VF256
Supported DevicesSmartFusion2M2S025, M2S025T, M2S025TSM2S010, M2S010T, M2S025TSM2S005, M2S005S
IGLOO2M2GL025, M2GL025T, M2S025TSM2GL010, M2GL010T, M2GL025TSM2GL005, M2GL005S
Top View
Side View
Bottom View256 SOLDER BALLS
E
D
D1
ddd
e
e
eee
aaab
A
A1 fff
A2
ccc
A1 BALL PAD CORNER
A1 BALL PAD CORNER
E1
C C
C
SEATING PLANE
5193068 PD3068 Datasheet Revision 62.0 96
Package Mechanical Drawings
Figure 72 • Package Outline of VF400
The following table lists the supported devices for VF400.
2.16.2 Dimensions of VF400The following table lists the dimensions of VF400.
Table 89 • Supported Devices for VS400
Supported DevicesM2S005, M2S005SM2S010, M2S010T, M2S010TSM2S025, M2S025T, M2S025TSM2S050, M2S050T, M2S050TSM2S060, M2S060T, M2S060TS
M2GL005, M2GL005SM2GL010, M2GL010T, M2GL010TSM2GL025, M2GL025T, M2GL025TSM2GL050, M2GL050T, M2GL050TSM2GL060, M2GL060T, M2GL060TS
Table 90 • Dimensions of VF400
JEDEC Equivalent VF400, page 96Dimension Min. Nom. Max.A 1.31 1.41 1.51
A1 0.32 0.37 0.42
A2 0.65 0.70 0.75
aaa 0.12
b 0.41 0.46 0.51
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
ABCDEFGHJKLMNPRTUVWY
A1 Ball Pad Corner
eee C
fff CA B
Side View
D1/E1 SQ
Detail A
// ccc C
aaa C
A
C
A1
A2
NX Ø b
Detail A
C
EE1
Top View Bottom View
A1 Ball Pad Corner
A
0.10 (4X)
B
e
e
(0.90)
(0.90)
D
D1
5193068 PD3068 Datasheet Revision 62.0 97
Package Mechanical Drawings
Note: All dimensions are in millimeters.
2.16.3 Dimensions of VF256The following table lists the dimensions of VF256.
Note: All dimensions are in millimeters.
Note: BSC = Basic spacing between centers.
c 0.29 0.34 0.39
ccc 0.10
D/E 17.00 BSC
D1/E1 – 15.20 –
e 0.80 BSC
eee 0.15
fff 0.08
Table 91 • Dimensions of VF256
JEDECEquivalent VF256, page 95Dimension Min. Nom. Max.A 1.36 1.46 1.56
A1 0.35 0.40 0.45
A2 0.65 0.70 0.75
aaa 0.12
b 0.45 0.50 0.55
ccc 0.10
D 14.00
D1 12.00 BSC
E 14.00
E1 12.00 BSC
ddd 0.10
fff 0.08
e 0.80 TYP
eee 0.15
Table 90 • Dimensions of VF400
5193068 PD3068 Datasheet Revision 62.0 98