PC-1K BASECOAT

PC-1K BASECOAT

May. 2021 YATU ADVANCED MATERIALS CO., LTD

DESCRIPTION:Perfecoat single component basecoat has solid colors,metallic and pearl effect. It is made from weatheringresistant resins with high quality, strong coverage power,and excellent adhesion power..COMPONENTS:PC-1K BasecoatP-5 Fast Reducer <59°FP-1/2 Standard/Slow Reducer 59-86°FP-2 Slow Reducer >86°F

SUBSTRATES:Sanded and dried existing finishes, 1K or 2K primer

SURFACE PREPARATION:Remove wax, silicon or other contaminationswith 3910 degreaser.

MIX RATIO:

PC-1K Basecoat 2 partsP-5/P-1/P-2 1 part

POT LIFE:

2 hours @ 68°F

ADDITIVES: Blushing: 3960 Retarder Solvent over 86°F. Refer to techsheet of Retarder Solvent for details.

Fisheyes: 3930 Anti Silicon (0.5-1%) in the paint remainedand re-spray the affected area.

APPLICATION:Spray gun set up:1.3-1.6 mm or equivalentAir pressures:HVLP: 8-10 psi at the air capCompliant: 28-35 psi at the gun

Please refer to gun manufacturer for proper spray pressurerecommendations.

Coats: 2 wet coatsFlash off time: 5-10 mins.between coats @ 68°FAir drying: allow 5 mins. Purgetime before baking

DRY TIME:@ 68°F

Dust free: 30 minutesDry to buff: overnight

@ 140°FBake time: 25-30 minutes

CLEARNING:Clean equipment immediately with solvent after application

Shelf Life：2 years in original sealed can at cool and dry place at 68°F

PACKAGING:1L, 4L

PHYSICAL DATA:VOC(g/L): 770

FOR PROFESSIONAL USE ONLYRead MSDS Before Use

NOTE: The information in this data sheet is based on our knowledgeand the current laws. It is always the responsibility of the user to fulfillthe requirements of local rules and legislations. The uncertain factorsmay affect the application of products, such as the condition ofsubstrate. We do not accept any liability on loss, damage andperformance of products unless we issue a special agreement.Always read the latest Material Data Sheet and the Technical Datasheet before applying the products.

PC-2K TOPCOAT


DESCRIPTION:Perfecoat 2K Topcoat has good hardness, high gloss andbuild, excellent protective and coverage power with longlasting bright color..COMPONENTS:PC-2K TopcoatPC-801 Fast Activator <65°FPC-802 Standard Activator 65-86°FPC-803 Slow Activator >86°FSUBSTRATES:Sanded and dried existing finishes, 1K or 2K primer


MIX RATIO:

PC-2K Topcoat 2 partsPC-801/802/803 1 part

POT LIFE:

2 hours @ 68°F



Overspray: 3920 Thinner SRA. Refer to tech sheet ofThinner SRA for details.



Coats: 2 wet coatsFlash off time: 5-10 mins. between coats @ 68°FAir drying: allow 5 mins. purge time before baking.

DRY TIME:@ 68°F

Dust free: 30 minutesDry to buff: overnight



Shelf Life：2 years in original sealed can at cool and dry place at 68°F

PACKAGING:1L, 4L




PC-600 CLEARCOAT


DESCRIPTION:Perfecoat PC-600 is double-pack economical acrylic clearcoat with high gloss and hardness. It is fast drying andsuitable for metal surface.

COMPONENTS:PC-600 Clear CoatPC-601Fast Activator <65°FPC-601 Fast Activator/PC-602 Standard Activator 65-75°FPC-602Standard Activator 77-86°FPC-603 Slow Activator >86°FSUBSTRATES:Sanded and dried existing finishes, 1K or 2K primer


MIX RATIO:

PC-600 4 partsPC-601/602/603 1 part

POT LIFE:PC-601/602, 2 hours @ 68°FPC-603, 3 hours @ 68°F

ADDITIVES: Blushing:3960 Retarder Solvent over 86°F. Refer to techsheet of Retarder Solvent for details.



APPLICATION:Spray gun set up:Gravity feed: 1.2-1.5mmSiphon feed: 1.4-1.7mm


Coats:2coats

Flash off time: 5-10 mins. between coats @ 68°FAir drying: allow 15-20 mins.timebefore baking.

DRYTIME:

@ 77°FDust free: 30 minutesDry to Polish: 16 hours

@ 158°FDust free: 5 minutesDry to Polish: 60 minutes



FOR PROFESSIONAL USE ONLY

Read MSDS Before UseNOTE: The information in this data sheet is based on our knowledgeand the current laws. It is always the responsibility of the user to fulfillthe requirements of local rules and legislations.The uncertain factorsmay affect the application of products, such as the condition ofsubstrate. We do not accept any liability on loss, damage andperformance of products unless we issue a special agreement.Always read the latest Material Data Sheet and the Technical Datasheet before applying the products.

PC-700 MS CLEARCOAT


DESCRIPTION:Perfecoat PC-700 MS is medium clearcoat designed foroverall and panel refinishing. Good gloss and is theeconomical choice for body shops..COMPONENTS:PC-700 MS ClearcoatPC-701 Fast Activator <65°FPC-702 Standard Activator 65-86°FPC-703 Slow Activator >86°F



MIX RATIO:

PC-700 2 partsPC-701/702/703 1 part

POT LIFE:

2 hours @ 68°F







DRY TIME:

@ 68°FDust free: 30 minutesDry to buff: overnight






PC-800W SUPER CLEARCOAT


DESCRIPTION:Perfecoat PC-800W Super Clearcoat offers smooth paintfilm and good gloss with durable resistance to weather andpollution. It can be used for small spot repairs and overallrefinish and it is easy to apply..COMPONENTS:PC-800W Super ClearcoatPC-801 Fast Activator <65°FPC-802 Standard Activator 65-86°FPC-803 Slow Activator >86°F



MIX RATIO:

PC-800W 2 partsPC-801/802/803 1 part

POT LIFE:

2 hours @ 68°F







DRY TIME:




PHYSICAL DATA:VOC(g/L)：480



PC-5000 HIGH GLOSS CLEARCOAT


DESCRIPTION:Perfecoat PC-5000 HS High gloss clearcoat has mirroreffect and deep rich gloss. It is suitable for overall refinishand spot repair while offering durability, yellowing resistanceand excellent chemical resistance..COMPONENTS:PC-5000 HS High gloss clearcoatPC-5001 Fast Activator <65°FPC-5002 Standard Activator 65-86°FPC-5003 Slow Activator >86°F



MIX RATIO:

PC-5000 2 partsPC-5001/5002/5003 1 part

POT LIFE:

2 hours @ 68°F







DRY TIME:






Read MSDS Before UseNOTE: The information in this data sheet is based on our knowledgeand the current laws. It is always the responsibility of the user to fulfillthe requirements of local rules and legislations. The uncertain factorsmay affect the application of products, such as the condition ofsubstrate. We do not accept any liability on loss, damage andperformance of products unless we issue a special agreement.Always read the latest Material Data Sheet and the Technical Datasheet before applying the products.

PC-6000 EXTRA FAST CLEARCOAT


DESCRIPTION:Perfecoat PC-6000 Extra fast clearcoat has high gloss andhardness. It is easy to apply and suitable for fast spotsrepairs, low consumption and high efficiency to ensure goodprofit.

COMPONENTS:PC-6000 Extra Fast ClearcoatPC-6001 Fast Activator <77°FPC-6002 Standard Activator >77°F



MIX RATIO:

PC-6000 2 partsPC-6001/6002/6003 1 part

POT LIFE:

2 hours @ 68°F







DRY TIME:

@ 68°FDust free: 10 minutesDry to buff: 2 hours






PC-6400 SUPER FAST CLEARCOAT(4:1)


DESCRIPTION:Perfecoat PC-6400 Super Fast Clearcoat(4:1) is eco-friendlytwo-pack extra fast drying clear coat with certain amount ofexempt solvent, made from modified acrylic polyols, lowVOC emission, high gloss, suitable for metal surface.

COMPONENTS:PC-6400 Super Fast ClearcoatPC-6401 Fast ActivatorPC-6402 Standard ActivatorPC-6403 Slow ActivatorSUBSTRATES:1K basecoat


MIXRATIO:

POT LIFE:

0.5 hours @ 86°F after mixing.

APPLICATION:Spray gun set up:Gravity feed:1.2-1.5 mm 3-5kg/cm2

Siphon feed:1.4-1.7mm 3-5kg/cm2


Coats & Thickness:2-3 Coats, about 40-60μmFlash off time: 0-3mins. betweencoats @ 77°F, then leave 15-20mins before baking.

PACKAGING:1L,4L

DRY TIME:@ 77°FTack free: 20 mins Dry to handle: 50 minsDry to polish: 60mins@ 158°FTack free: 5 mins Dry to handle: 10 minsDry to polish: 15 mins

Re-applicationIf there are particles or runs after spray, wet sand theaffected area with P2000 sand paper after thorough drying,then polish to solve the problem.

CLEARNING:Clean equipment immediately with solventafter application

Note: When ambient temperature is lower than 41°F, to fast

the film drying time, allow a full bake at 140°F. Thinner should be added with Retarder Solvent at

temperature higher than 86°F.Details please refer tothe technical data sheet of Retarder Solvent.

In the event of fisheyes during application, add 0.5-1%Anti Silicon in the paint remained and re-spray theaffected area.

In the overspray area of new and existing finish, applydirectly Thinner SRA to achieve an invisible transition.Details please refer to the technical data sheet ofThinner SRA.

The products mixed with hardener should be used upwithin 0.5 hour.

Shelf Life: 2 years in original sealed can at cool and dryplace at 68°F.

PHYSICAL DATA:VOC(g/L)：520



Clear Coat + Hardener

By volume 4 1＜64.4°F64.4-75.2°F77-86°F＞86°F

PC-6400(4:1)PC-6400(4:1)PC-6400(4:1)PC-6400(4:1)

PC-6401PC-6401/PC-6402

PC-6402PC-6403

PC-3340 PLASTIC PRIMER


DESCRIPTION:Perfecoat PC-3340 is a single-component transparent fastdrying primer. It is used to promote adhesion of paint systemto plastic parts.

COMPONENTS:PC-3340 Plastic Primer

SUBSTRATES:Plastic parts PP, PA, PE.


MIX RATIO:

Packaged ready to use

Recoating

Re-coating with primer after flash-off time of 10-15 minutes.



Coats: 2 wet coatsFlash off time: 5-10 mins. between coats @ 68°F

Note:

It is recommended not to spray thickly to avoid peelingoff.

Test is recommended before application due to thevariety of plastic parts.


PHYSICAL DATA:

VOC(g/L): 840



PC-3352 EPOXY PRIMER


DESCRIPTION:Perfecoat PC-3352 gives excellent rust proofing for baremetal, good adhesion power to steel, aluminum andgalvanized steel.

COMPONENTS:PC-3352 Epoxy PrimerPC-3652 HardenerPC-3750 Reducer

SUBSTRATES:Dried and sanded existing finishes, steel, iron and glassfiber reinforced plastic.


MIX RATIO: ≥86℉

POT LIFE:

4-6 hours @ 77°F with hardener

RecoatingAfter drying and sanding, re-coat with putty, primer surfacerand all kinds of topcoat.

SPRAY GUN SET UPGravity feed:1.2-1.4 mm 3-5kg/cm2



PACKAGING:5KG

Coats & Thickness:2-3 coats, total 40-60 um

Flash off time:5-10mins. between coats @

77°FDRY TIME:

@ 68°F18-26 hours

@ 140°F40-60 minutes

Note: For oxidized iron and cast iron, shot blasted sa 2.5

class with roughness of 30-75 um, or acid wash theoxidized parts to get rid of rust.

It is recommended to bake at 140-158 ℉ for 30minutes when temperature is below 50℉ for bettercuring of paint film.

Choose right hardener and thinner to avoid poor curingof paint film.

Shelf Life: 2 years in original sealed can at cool and dryplace at 68℉.

SANDING:Dry sanding: P240-P400Wet sanding: P600-P800





Product Weight VolumePC-3352 EpoxyPrimer 5 3.5

PC-3652Hardener 1 1PC-3750 Reducer 1-1.5 1

PC-3450 1K PRIMER SURFACER


DESCRIPTION:Perfecoat PC-3450 fast drying one pack primer surfacer,suitable to cover minor defects in surface of putty or existingfinish. It is easy to apply with good filling power and ease ofsanding for economical refinishing.

COMPONENTS:PC-3450 1K Primer SurfacerP-1 Reducer

SUBSTRATES:Dried and sanded existing finishes and putty.


MIX RATIO:

+

APPLICATION:Spray gun set up:Gravity feed:1.4-1.8mm 3-5kg/cm2



Coats & Thickness: 2- 3 coatsFlash off time: 5-10 mins.between coats @ 68°F

DRY TIME:

@ 68°F30 minutes



PACKAGING:4KG

Note: Shelf Life: 2 years in original sealed can at cool and

dry place at 68°F. Not recommended for direct application over

substrate of bare metal and wood. Recommended to use 2K Primer to achieve good

adhesion to substrate and excellent gloss and filmbuild of the topcoat.

Not recommended to use thinner of fast drying type.




Reducer1-1.5P-1

1K Primer Surfacer1

PC-3450

PC-3460 FILLER


DESCRIPTION:Perfecoat PC-3460 is a single-component putty with goodfilling power, fast drying, easy to apply and sand, suitable tocover small scratches, sand holes and pinholes.

COMPONENTS:PC-3460 Filler

SUBSTRATES:Dried and sanded existing finishes, putty, 1K & 2K primer

SURFACE PREPARATION:

Remove wax, silicon or other contaminationswith 3910 degreaser.

MIX RATIO:

Packaged ready to use, apply with spreader.Apply a thin coat at a time.

APPLICATION TOOL:Putty knife, soft rubber or plastic spreader.

DRYTIME:

@ 68°F30 minutes

Allow longer drying time for thick coating.


PACKAGING:1kg

Note: Not recommended to apply over large area. Not suitable for direct application over bare metals. Spray topcoat directly after sanding if the application

area is small. It is recommended to use 2K primersurfacer prior to topcoat if the application area is large.

Seal the can tightly after use to avoid skinning. Shelf Life: 2 years in original sealed can at cool and dry

place at 68°F



Read MSDS Before Use


PC-4648 2K PRIMER SURFACER (4:1)


DESCRIPTION:Perfecoat PC-4648 (4:1) multi-purpose primer surface hasstrong filling power and fine adhesion between coats. It hasexcellent flexibility and impact resistance which can increasegloss and build of topcoat.

COMPONENTS:PC-4648 2K Primer Surfacer (4:1)PC-4661 Fast Activator <77°FPC-4662 Standard Activator >77°F

SUBSTRATES:Dried and sanded existing finishes, all kinds of Perfecoatprimer and putty


MIX RATIO:

PC-5000 2 partsPC-5001/5002/5003 1 part

POT LIFE:

2 hours @ 68°F

Recoating

After drying and sanding, re-coat with all kinds of topcoat.



Coats: 2 wet coatsFlash off time: 5-10 mins.

between coats @ 68°FAir drying: allow 5 mins. purge time before baking.

DRY TIME:

@ 68°F2~3 hours

@ 140°FBake time: 30 minutes





PC-4840 DTM 2K PRIMER (4:1)


DESCRIPTION:Perfecoat PC-4840 DTM 2K PRIMER (4:1) is multi-purposedouble pack primer surfacer, with strong filling power andfine adhesion on steel and zinc plates, has excellentflexibility and impact resistance which can increase glossand build of topcoat.

COMPONENTS:PC-4840 (4:1) DTM 2K PrimerPC-4662 Standard Activator

SUBSTRATES:Dried and sanded existing,sanded steel and zinc platescleaned with degreaser, a epoxy primer and putty.

SURFACE PREPARATION:Remove wax, silicon and other contaminationswith 3910 degreaser.

MIX RATIO:

POT LIFE:

0.5 hours @ 77°F after mixing.

APPLICATION:Spray gun set up:Gravity feed: 1.4-1.8mmSiphon feed: 1.7-2.0mmConventional: 1.5-2.5 bar

RP: 0.5-2.0 bar HVLP: 0.7-2.0 barPlease refer to gun manufacturer for proper spray pressurerecommendations.

PACKAGING:PC-4840: 4kg PC-4662/4661: 1L

Coats & Thickness:2-3 Coats, 50-80um,5-10 mins between coats, thenleave 15-20mins before baking.Flash-off: 5-10 mins @77°F

DRY TIME:@ 77°F4~5 hours@ 140°F45 minutes

SANDING:Dry sanding: 400#-600#Wet sanding: 800#-1000#

Re-applicationAfter drying and sanding, it can be sprayed with varioustopcoats.


Note: Shelf Life: 2 years in original sealed can at cool and

dry place at 68°F..PHYSICAL DATA:VOC(g/L): 580



Product Weight Volume

PC-4840 （ 4:1）DTM 2 Primer

100 4

PC-4662 StandardActivator

20 1

PC-6234 2K SEALER


DESCRIPTION:Perfecoat PC-6234 multi-purpose double pack 2K sealer,with strong filling power and fine adhesion, has excellentflexibility and impact resistance which can increase glossand build of topcoat. Smooth paint film and non-sandingapplication.

COMPONENTS:PC-6234 2K SealerPC-6256 Fast Activator <64.4°FPC-6257 Medium Activator 64.4°F—86°FPC-6258 Slow Activator >86°F

SUBSTRATES:Dried and sanded existing paint film, primes and puttys.


MIX RATIO:

POT LIFE:@ 77°F30 minutes with PC-625645 minutes with PC-6257/PC-6258

APPLICATION:Spray gun set up:Gravity feed:1.4-1.6mm 3-5kg/ cm2



Coats & Thickness:1-2 Coats, 30-40 umFlash off time:5-10mins betweencoats @ 77°F

DRY TIME:@ 77°F

4~6 hours@ 158°F

30 minutesSANDING:Non sanding：spray topcoat after surface dryingDrying sanding: P400#-600# Wet sanding: P800#-1000#Re-applicationAfter surface drying or sanding, spray topcoats.

CLEARNING:

Clean equipment immediately with solventafter application

Shelf Life：2 years in original sealed can at cool and dryplace at 68°F.




Temperature Product Weight Volume

<64.4°FPC-6234 100 100PC-6256 20 25P-1 Medium Reducer 20-30 20-30

64.4 -86°FPC-6234 100 100PC-6257 20 25P-2 Slow Reducer 20-30 20-30

＞86°F

PC-6234 100 100PC-6258 20 25P-2 Slow Reducer orP-3 Extra Slow Reducer 20-30 20-30

PC-3910 DEGREASER


DESCRIPTION:Perfecoat PC-3910 Degreaser is designed to remove grease, oil, and other surface contaminants toavoid paint film defects.

COMPONENTS:PC-3910 Degreaser

SUBSTRATES:Existing finishes, primer, putty and metal.

MIX RATIO:

Packaged ready to use

APPLICATION:◆Clean the substrate with water to remove water-soluble contaminants and then dry it off.◆Degrease the substrate with tack rag wetted with degreaser.◆Wipe and dry the surface with another clean tack rag.

PHYSICAL DATA:

VOC（g/L）: 740



NOTE: The information in this data sheet is based on our knowledge and the current laws. It is always theresponsibility of the user to fulfill the requirements of local rules and legislations. The uncertain factors may affect theapplication of products, such as the condition of substrate. We do not accept any liability on loss, damage andperformance of products unless we issue a special agreement. Always read the latest Material Data Sheet and theTechnical Data sheet before applying the products.

PC-3920 THINNER SRA


DESCRIPTION:PC-3920 Thinner SRA is designed for dissolving the rough overspray area of new and existing finishesand achieve an invisible transition for panel repair.

Can be used in:Overspray area of Perfecoat 2K solid colors, clearcoat in panel repairs.

Note: Not suitable with 1K basecoat and primers.

COMPONENTS:PC-3920 Thinner SRA

MIX RATIO:

Packaged ready to useMix with the paint remained in the spray gun in the ratio of 1:1

APPLICATION:Spray slightly one coat over the overspray area with Thinner SRA right after the finish. Second coat in20 seconds.

PHYSICAL DATA:

VOC(g/L): 930




PC-3930 ANTI SILICON


DESCRIPTION:Additive for 2K solid colors or clear coats, able to remove fisheyes or craterings on the paint film.

COMPONENTS:PC-3930 Anti Silicon

MIX RATIO:

PC-2K topcoat / clear coat: 1 QTPC-3930: 0.5-2 tin cap (about 4-15g)

APPLICATION:Spray one or two coats over the paint film with fisheyes or craterings by paint mixed with PC-3930.

Notes：◆ Use according to the recommended ratio. Excess addition may cause defect of small bubbles or pin

holes.◆ In serious defects, fisheyes affected paint film must be sanded out and filled when it is hard dry.

Refinish with paint mixed with PC-3930.

PHYSICAL DATA:

VOC(g/L): 860




PC-3940 MATTING AGENT


DESCRIPTION:Perfecoat PC-3940 Matting Agent is designed to reduce the brightness of the paint film. Good mattingability with smooth paint film. Suitable for 1K and 2K system.

COMPONENTS:PC-3940 Matting Agent1K basecoat/2K TopcoatHardener

SUBSTRATES:Match with 2K solid colors, clear coats and 1K basecoat.

MIX RATIO:

APPLICATION:Refer to the technical data sheet of the matching products for proper application.

Note: The matting agent is easy to crystallize when exposed to air too long. To avoid particles in the paint film, especially when applied in combination with clear coat, remove

crystallized particles and other contaminations around the can rim before use and pour out withfilter.

Shelf Life: 2 years in original sealed can at cool and dry place at 68°F.


PACKAGING:1L


Read MSDS Before UseNOTE: The information in this data sheet is based on our knowledge and the current laws. It is always theresponsibility of the user to fulfill the requirements of local rules and legislations. The uncertain factors may affect theapplication of products, such as the condition of substrate. We do not accept any liability on loss, damage andperformance of products unless we issue a special agreement. Always read the latest Material Data Sheet and theTechnical Data sheet before applying the products.

1KBasecoat 1K Basecoat : PC-3940 = (85-70) : (15-30)

2KTopcoat

Effect 2K Topcoat PC-3940 HardenerAll matte 30 parts 70 parts 15 partsHalf matte(egg shell) 50 parts 50 parts 25 parts

Half bright 70 parts 30 parts 35 parts

PC-3960 RETARDER SOLVENT


DESCRIPTION:PC-3960 Retarder Solvent is additive to prolong volatilization of solvent. It helps to produce a qualityrefinishing job of good leveling and blushing-free at circumstances of high temperature, humidity orlarge area repair.

COMPONENTS:PC-3960 Retarder Solvent

MIX RATIO:

Add 10-30% retarder solvent into P-2 or P-3 reducer when the ambient temperature isover 86°F





PC-3980 QUICK DRIER


DESCRIPTION:

PC-3980 quick drier is specially designed for Perfecoat 2K topcoat and Clearcoat. It can speed up thedust free time and air drying time of paint film. It is suitable for spot repair or application at lowtemperature.

COMPONENTS:PC-3980 Quick Drier

MIX RATIO:

◆ 50℉to 59℉: 5-6 gram PC-3980 per RTS 1 quart

◆ 32℉ to 50℉: 6-10 gram PC-3980 per RTS 1 quart

◆ Below 32°F: 10-15 gram PC-3980 per RTS 1 quart

Note:

◆Pot life of paint mixed with PC-3980 quick drier would be shortened considerably, use up as soon aspossible.

◆Not recommended addition of PC-3980 quick drier is over 15 gram per RTS 1 quart, otherwise, itwould cause paint film embrittlement and loss of gloss

◆ PC-3980 quick drier cannot be used as activator.

PHYSICAL DATA:

VOC(g/L): 880




PC-GT20 SPEED PRIMER PLUS


DESCRIPTION:PC-GT20 Speed Primer Plus is a highly productive 2K primer surfacer designed for the high-productionshop who demands premium quality and maximum throughput with reduced cycle time. It offers easyapplication and sanding with excellent gloss holdout for all topcoats.

PC-GT20 Speed Primer Plus can be sanded in 20 minutes by air drying or 5 minutes by force drying forspot or panel repair job. Matching with different hardener and thinner, the product can be converted togeneral sanding primer surfacer with fast air and force drying properties for repair job more than 2panels, or wet-on-wet primer for new body parts.

Product Features:1.Dry-to-sand in 20 minutes at 68°F2. Easy to apply, high performance of filling, sealing, flow and sandiablilty3. Excellent holdout for topcoat4. Highly productive, improves shop throughput5. Versatility: Suitable for rapid, standard, overall repairs，or wet-on-wet process for new parts

Product Specification Sheet:

Tack Free Rapid Standard Overall Non-sanding

The amount ofapplicablepanel(s)

1-2 3-5 6 - full body new panels

MatchedHardener PC - GT201 PC - GT201 PC - 6641 PC - GT201

MatchedThinner PC - GT202 PC - 1/ - 2/ - 3

Mixing Ratio

Weight：4:1:1.8-2Volume：3:1:1.8-2

(Primer surfacer+8% 2k solidcolor):Hardener : ThinnerWeight：4:1:2.5Volume：3:1:2.5-3

Pot Life(77°F)

20 minutes 40 minutes 1.5 hours 20 minutes

ApplicableViscosity 15 -18 seconds 13 - 15 seconds

PC-GT20 SPEED PRIMER PLUS


Spray gunset up Gravity RP Spray, Feed 1.6mm - 1.8mm Feed 1.3mm - 1.5mm

1.8 - 2.0 bar 1.8 - 2.0 bar

CoatsWet spray 2-3 coats

Thickness of paint film: 40 - 50 um 25 - 35 um

Flash Time

1 minute orno flash

2 - 3minutes 3 - 5 minutes 1 minute or no flash

Dry to sand 20 minutes(77°F)

40 minutes(77°F)

1.5 - 2hours(77°F) Apply topcoat until the paint

film is matte.(77°F, 10 minutes)5 minutes

(140°F)10 minutes(140°F)

20 minutes(140°F)

Note: It is recommended to choose conventional thinner for rapid repair when temperature is over 95°F. For rapid repair and spraying, mix moderate primer surfacer, spray it within 20 minutes, and then

clean the spray gun immediately. For the color tuning and non-sanding primer surfacer application process over new panels , the 2k

solid color should be added less than 8%.





PC-1K BASECOAT

Documents

Transcript of PC-1K BASECOAT