PARTS ORDERING GUIDE - Bush Hog

20

Transcript of PARTS ORDERING GUIDE - Bush Hog

©2011 Alamo Group Inc.

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in pro-

cessing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong

to the basic machine featured in this manual. Part Numbers and Descriptions are given

to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organiza-

tion ordering the parts, who should be charged, and if possible, the serial number of the

machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct

part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked

and are subject to special handling. Request a quotation for such parts before sending

a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

For maximum safety and to guarantee optimum product reliability, always

use genuine BUSH HOG Parts. The use of inferior replacement parts may

causepremature or catastrophic failure which could result in serious injury

or death.Direct any questions regarding parts to:

BUSH HOG2501 Griffin Ave.

Selma, AL 36703

www.bushhog.com

Contact Us

800-304-2836

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-mindedoperator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer hasdesigned this implement to be used with all its safety equipment properly attached to minimize the chance ofaccidents.

BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rulesof safety and common sense!

WARRANTY INFORMATION:Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on theWarranty Card and on the Warranty Form that you retain.

LIMITED WARRANTY

Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized BushHog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year fornon-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. Theobligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defectiveparts.

Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warrantyperiod, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hogdealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which areclaimed to have been defective in material or workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESBush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied orexpressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale oruse of the items warranted. Such incidental and consequential damages shall include but not be limited to:transportation charges other than normal freight charges; cost of installation other than cost approved by BushHog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental ofsubstitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or partsresulting from acts beyond the control of Bush Hog.

THIS LIMITED WARRANTY SHALL NOT APPLY:1. To vendor items which carry their own warranties, such as engines, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgementof Bush Hog such use affects its performance, stability or reliability.

4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in thesole judgement of Bush Hog, affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, wornblades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.

6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in thecompany’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITEDWARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE INWRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA36703.

Record the model number, serial number and date

purchased. This information will be helpful to your

dealer if parts or service are required.

MAKE CERTAIN THE WARRANTY

HAS BEEN FILED WITH BUSH HOG

SELMA, ALABAMA

MODEL NUMBER ________________________________

SERIAL NUMBER ________________________________

DATE OF RETAIL SALE ___________________________

PART NAME INDEX

©2011 Alamo Group Inc.

RD5 RD6

RD5 RD6 A FRAME STANDARD ASSEMBLY..................................................................................................88-1-1

RD5 RD6 A FRAME STANDARD ATTACHMENT.............................................................................................88-1-2

RD5 RD6 BLADE BAR ASSEMBLY ..................................................................................................................88-1-3

RD5 RD6 DRIVELINE ASSEMBLY (COMER)...................................................................................................88-1-4

RD5 RD6 DRIVELINE ASSEMBLY (BONDIOLI & PAVESI)) ............................................................................88-1-5

RD5 RD6 DRIVELINE ASSEMBLY....................................................................................................................88-1-6

RD5 RD6 GEARBOX ASSEMBLY ....................................................................................................................88-1-7

RD5 RD6 GEARBOX ATTACHMENT (SHIELDING).........................................................................................88-1-8

RD5 RD6 FRONT AND REAR DEFLECTORS..................................................................................................88-1-9

RD5 RD6 TAILWHEEL ASSEMBLY .................................................................................................................88-1-10

RD5 RD6 WHEEL ASSEMBLY CASTER FORK .............................................................................................88-1-11

RD5 RD6 DECALS, SAFETY AND LOGO.......................................................................................................88-1-12

RD5 RD6 A FRAME STANDARD ASSEMBLY

©2011 Alamo Group Inc. 88-1-1

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

1 00766591 2 FLAT REAR BRACE

2 00764839 2 BAR, A-FRAME

3 00748598 1 HEXB 3/4-10 UNC 5-1/2 PL5

4 00757953 1 BUSHING 1-1/4 X 7/32 X 3 A-FRAME

5 00037200 1 LOCKNUT 3/4-NC TLM PLC

6 00757949 1 TOPLINK

RD5 RD6 A FRAME STANDARD ATTACHMENT

©2011 Alamo Group Inc. 88-1-2

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

1 00603500 2 ASY,CAT.1 HITCH PIN W/LW & NUT

2 ---------- 2 LOCKWASHER

3 ---------- 2 HEX NUT

4 2196 2 CLIP, LYNCH PIN 13/32 DIA.

5 37107B12 1 CLEVIS PIN, TOP LINK - CAT. I

6 37107B13 1 PIN, HAIR CLIP

7 02030700 2 HHCS, 1/2-13NC X 1-1/4 PL5

8 00001800 2 TOPLOCKNUT, 1/2-13 NC PL

9 00785955 1 DECK WELDMENT for RD5

00786237 1 DECK WELDMENT for RD6

RD5 RD 6 BLADE BAR ASSEMBLY

©2011 Alamo Group Inc. 88-1-3

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

1 00787299 1 WLDMT, BLADE BAR (RD5)

00787325 1 WLDMT, BLADE BAR (RD6)

2 00781341 2 BLADE, FAN CCW, 22-1/2 CTR-TIP (RD5)

00785567 2 BLADE, FAN CCW, 25-1/2 CTR-TIP (RD6)

3 00781320 2 BLADE BOLT 7/8 DIA X 3 LG

4 00761535 2 WASHER, 7/8 STR PLAIN

5 00750226 2 NUT, TOPLOCK 7/8 NF PLC

6 00786548 1 BLADE BOLT KIT (FOR 2 BLADES)

7 50073002 1 Blade Wing, RD5

8 50073005 1 Blade Wing, RD6

March, 2019

RD5 RD6 DRIVELINE ASSEMBLY (MFD. BY COMER)

©2011 Alamo Group Inc. 88-1-4

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

00768174B 1 DRIVELINE, SP

1 76711 1 ASSY,YOKE COLLAR - COMPLETE

2 64694 2 CROSS & BEARING KIT SERIES 40

3 00777329A 1 YOKE, 1-3/8 BORE SP

4 N/A 1 YOKE & OUTER TUBE

5 N/A 1 YOKE & INNER TUBE

6 78577 1 PIN ROLL 8MM X 60MM

7 78578 1 PIN ROLL INNER TUBE

8 00779534 1 COMPLETE SHIELD KIT

9 50017480 1 SLIDE COLLAR REPAIR KIT

10 50053144 1 RETAINER, INNER COLLAR

11 50053143 1 RETAINER, OUTER COLLAR

12 50056404 6 SHIELD BOLT, NYLON

THIS DRIVELINE MANUFACTURED BY COMER.

BEFORE ORDERING REPAIR PARTSFIRST DETERMINE

IF THE DRIVELINE IS A COMER OR A BONDIOLI & PAVESI

MANUFACTURED DRIVELINE .

THIS DRIVELINE REPLACED BY 50069230 DRIVLENE ASSY.

MANUFACTURED BY BONDIOLI & PAVESI.

COMER BRAND NAME ON SHIELDINGNOTE: IF PART NUMBERS 50063617 OR 00787393

ARE PRESENT ON THE OUTER SHIELDING YOUMUST ORDER PARTS FROM THE 50069230 B& P dRIVELINE

RD5 RD6 DRIVELINE ASSEMBLY (MFD. BY BONDIOLI & PAVESI)

©2011 Alamo Group Inc. 88-1-5

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

50069230 1 DRIVELINE ASSEMBLY, B&P

1 50064902 1 ASSY,YOKE COLLAR - COMPLETE

2 64694 2 CROSS & BEARING KIT

3 78577 1 ROLL PIN 8MM X 60MM OUTER YOKE

4 78578 1 ROLL PIN 8MM X 55MM INNER YOKE

5 81447 1 YOKE 1-3/8” BORE W/ GREASE FITTING

6 50064911 1 SHIELD SUPPORT, OUTER

7 50064912 1 SHIELD SUPPORT, INNER

8 50064645 1 BALL COLLAR KIT

9 63946 6 GREASE FITTING

10 50069227 1 SHIELD KIT, COMPLETE

THIS DRIVELINE MANUFACTURED BY BONDIOLI & PAVESI.

BEFORE ORDERING REPAIR PARTS FIRST DETERMINE

IF THE DRIVELINE IS A BONDIOLI & PAVESI OR A COMER

MANUFACTURED DRIVELINE .

THIS DRIVELINE REPLACES THE 00768174B DRIVELINE ASSY.

MANUFACTURED BY COMER.

B&P Brand Name

on Shielding.

18

2

93 4 5

67

10

The B&P Driveline

Implement Yoke is round.

NOTE: If part numbers 50063617 or 00787393

are present on the outer shielding you must order

parts from the 50069230 B&P Driveline.

©2011 Alamo Group Inc. 88-1-6

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

50074691 1 DRIVELINE, Ser. 4 Shearbolt 540

1 50075056 1 Push Pin Yoke

2 50074282 2 Cross Kit

3 50075057 1 Plain Bore Yoke

4 78786 1 Safety Label Inner

5 78608 1 Safety Label Outer

6 ---------- 1 Outer Shield Cone

7 ---------- 1 Outer Shield Bearing

8 ---------- 1 Inner Shield Bearing

9 ---------- 1 Inner Shield Cone

10 50075058 1 Shield Complete

March, 2019

RD5 RD6 DRIVELINE ASSEMBLY REPLACES 50069230

RD5 RD 6 GEARBOX ASSEMBLY

©2011 Alamo Group Inc. 88-1-7

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

00786192 1 GEARBOX ASSY,- 40HP 540 RPM, 1:1.47 RATIO

2 0656220003 1 COVER,INPUT GEARBOX

3 00757683 1 COVER,OUTPUT GEARBOX

4 81634 1 SHAFT,INPUT - SMOOTH

5 00786196 1 KIT,ROLLER BEARING

6 00786197 1 KIT,BEVEL GEAR

7 00786198 1 KIT,SHIM

8 00758692 1 NUT,FLANGE HEX SLOTTED

9 88851 1 PLUG,VENT 1/2 - 14

10 00565000 1 PLUG,SOLID 1/8 - 27

11 7192 1 SNAP RING, DRIVE SHAFT RETAINER

12 00786214 1 SEAL, OIL-BOTTOM 40 x 54 x 9.5

13 00786213 1 SEAL, OIL-TOP 34.9 x 54 x 11

March, 2019

RD5 RD6 GEARBOX ATTACHMENT

©2011 Alamo Group Inc. 88-1-8

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

1 50068436 1 SAFETY SHIELD

2 00785574 1 GEARBOX SHIELD INNER SUPPORT RING

3 00023500 4 FLATWASHER, 5/16 TYPE,AW,ZP

4 00035900 4 5/16 X 3/4 HHCS

5 02845500 4 BOLT, 5/8 X 2 PL5

6 00756077 4 5/8 HARDENED WASHER

7 00695100 4 NUT,5/8 NC TOPLOCK

8 7A81324 1 SHEAR BOLT

9 00001800 1 LOCKNUT

10 7192 1 SNAP RING, DRIVESHAFT RETAINER

RD5 RD6 GUARD ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

1 50071639 1 Deflector, Front RD5

50071640 1 Deflector, Front RD6

2 02030700 7 HHCS, 1/2”-13NC x 1-1/4” PL5

3 4526 14 Nut, Flg Whiz 1/2-13 NC PL

4 00002700 7 Flatwasher, 1/2”

5 00785669K 1 Band, Rear RD5

00785681K 1 Band, Rear RD6

6 000514 7 Carr. Bolt, 1/2” x 1-1/4” PL5

©2011 Alamo Group Inc. 88-1-9

RD5 RD6

March, 2019

RD5 RD6 TAILWHEEL ASSEMBLY

©2011 Alamo Group Inc. 88-1-10

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

1 00780829 1 WLDMT, TAILWHEEL BEAM

2 ------------ 1 SEE (CASTER FORK & WHEEL ASSY)

3 00764375 2 CAPSCREW 1/2” NC X 3-1/4“ PL5

4 00001800 2 NUT, 1/2”-13 NC PL,TOPLOCK

5 00695100 1 NUT,5/8” NC, TOPLOCK

6 44107BH 1 CAPSCREW 5/8 NC X 3-1/2” GR5

7 00780878 3 RIVET, 3/16 POP X 15/32" G.R.

8 50035829 1 CANISTER, OPERATORS MANUAL

RD5 RD6 WHEEL ASSEMBLY & CASTER FORK

©2011 Alamo Group Inc. 88-1-11

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

1 00776224 1 FORK CASTER ASSEMBLY

2 15B2000 1 WASHER SAE 1 1/4” PLATED

3 00036900 1 PIN-COTTER 1/4” X 2-1/2“

4 00776211 1 BOLT SPINDLE M24 x 2 x 186

5 00776212 1 NUT, SPINDLE M24 X 2

6 0891030201 2 BUSHING, SINTERED IRON

7 00772082 1 GREASE FITTING M8 X 1

8 00756760 1 WHEEL ASSEMBLY 16 X 4

RD5 RD6 DECALS - SAFETY AND LOGO

©2011 Alamo Group Inc. 88-1-12

RD5 RD6

ITEM PART NO. QTY. DESCRIPTION

00781352 1 SHEET, SAFETY DECAL (Items 4, 11, 18)

00787356 1 RD5 SHEET DECAL, LOGOS (Items 1, 2, 3, 5, 6, 7, 8, 10, 16, 17)

00787357 1 RD6 SHEET DECAL, LOGOS (Items 1, 2, 3, 5, 6, 7, 8, 10, 16, 17)

1 D395 1 Decal, Replace Blades in Pairs

2 D454 1 Decal, Mower Can Fall Shipping

3 D590 1 Decal, Lubrication Chart

4 D388 1 Decal, Danger, Driveline Hazard

5 D549 1 Decal, Danger/Operation

6 D813 1 Decal, Danger, Multilingual

7 50065309 2 Decal, Bush Hog-14.85”

8 50068911 1 Model Decal, RD5

50068912 1 Model Decal, RD6

9 2738332 2 Decal, Red Oblong Reflector

10 D572 1 Decal, Danger, Entanglement

11 00756004 1 Decal, Danger, Guard Missing

12 03200347 1 Emblem, SMV

13 50035829 1 Canister, Operators Manual

14 50068908 1 Operator’s Manual

15 00780878 3 Rivet, 3/16 POP x 15/32” G.R.

16 D559 1 Decal, Genuine BH Parts

17 D137 1 Decal, CCW Blade Rotation

18 D614 2 Decal, Danger-Do Not Operate (Shield Missing)

2501 GRIFFIN AVE.• SELMA, AL 36703WWW.BUSHHOG.COM