Parts List5 3305183R55 Label, Motorola 6 3305183R56 Label, HT1000 7 3505535X02 Felt, Speaker 8 See...
Transcript of Parts List5 3305183R55 Label, Motorola 6 3305183R56 Label, HT1000 7 3505535X02 Felt, Speaker 8 See...
Parts List
HT1000 Series
8/03
8/03
Parts List
HT1000 Series
REF.
NO. PART NO. DESCRIPTION
REF.
NO. PART NO. DESCRIPTION
1 4505896U02 Lever, PTT
2 3205902U01 Seal, PTT, and Actuator for
S404, S405, S406 S408
3 1505627V05 Cover, Front
4 ---- Label, Agency Approval; not field
replaceable
5 3305183R55 Label, Motorola
6 3305183R56 Label, HT1000
7 3505535X02 Felt, Speaker
8 See Note 1 Speaker (LS401) – not available
9 0705470V01 Bracket, Speaker Retainer
10 See Note 1 Microphone (MK401) – not available
11 1405330W02 Boot, Microphone
12 8405310W04 FLEX, Front Cover/Display
13 8405333W03 FLEX, Controls
14 3905517V01 Popple, PTT (p/o S406)
15 3605253V01 Knob, On/Off/Volume
16 Knob, Frequency
3605254V02 2-Frequency Radios
or
3605254V03 8-Frequency Radios
or
3605254V01 16-Frequency Radios
17 Escutcheon, Control Top
1305872U02 2-Frequency Radios
or
1305872U03 8-Frequency Radios
or
1305872U01 16-Frequency Radios
18 3205160W01 Seal, Actuator; for S101
19 2205159W01 Pin, Actuator; for S101
20 3205514W01 Seal, Accessory Connector
21 3205177Z01 Seal, Control Top
22 3205178Z01 Seal, Emergency Button
23 2705877U01 Housing, Switch
24 See Note 1 Switch, Toggle (S402) – not available
25 See Note 1 Potentiometer/Switch On/Off/Volume
Control (R401/S403) – not available
26 3905329W01 Popple, Emergency Button
27 See Note 1 LED (CR702A/CR702B) – not available
28 See Note 1 Switch, Frequency (S401) – not available
29 1505632V01 Cover, Switch Housing
30 ---- Spring, PA; not field replaceable,
order front shield (item 37) – not available
32 8405247V01 FLEX, Jumper
33 See Note 2 Plug, Connector (P404) – not available
34 3205820V01 Seal, Connector Plug
35 ---- Label, Rear; Information; not field
replaceable
36 3205176Z01 “O” Ring, Contoured/Seal, Antenna
37 2605891U03 Shield, Front
38 4005831W01 Bracket, RF Switch
39 ---- Housing, RF Switch
40 4105266V01 Spring, RF Switch
41 4405524V01 Piston, RF Switch
42 ---- Circuit Board, RF Switch
43 1505892U06 Chassis (Rear Cover)
44 3905838V01 Contact, Antenna Shield Ground
(800 MHz and 900 MHz radios only)
45 2605898U01 Shield, PA (800 MHz and 900 MHz
radios only)
46 7505334W01 Pad, Sound Dampening
47 0405717W01 Washer, PTT Seal
49 7505393N33 Pad, Shock
NOTES:
1. Refer to electrical parts list (miscellaneous) for part number and completedescription.
2. Refer to electrical parts list (transceiver board) for part number and completedescription.
8/03
Portable
Accessories
HT1000 Series
Chargers
Single unit chargers are available in either desktop or compact styles
for small system users. Multiple unit chargers can be wall or rack
mounted and are ideal for multi-shift operations. All chargers are
specifically designed to meet the requirements of batteries
manufactured by Motorola. All chargers listed are rapid rate and will
fully charge your battery in less than 3 hours.
Single Unit Compact Bi-Chemistry Chargers –Rapid Rate
The bi-chem charger has the power supply built into the line cord
giving the user a smaller base unit for easier storage. It also utilizes
an enhanced charging algorithm that will help maximize the life of
your batteries. It will rapid rate charge both NiCd and NiMH
batteries.
RPX4747A Compact Bi-Chem Charger, 110V
RPX4748A Compact Bi-Chem Charger, 230V Euro plug
RPX4749A Compact Bi-Chem Charger, 230V UK plug
Chargers
Multiple Unit Charger (MUC)
Multi-unit chargers offer six pockets that can be used to rapid
charge 1 to 6 batteries simultaneously. The batteries can be charged
with the radios or separately. They will rapid rate charge both NiCd
and NiMH batteries.
NTN1177D Six-Pocket,
rapid rate110V
NTN1178D Six-Pocket,
rapid rate, 220V (supplied
with 2 prong cord)
NTN1179D Six-Pocket,
rapid rate, 240V (supplied
with 3 flat prong cord)
MUC Accessories
NLN7967A Wall Mount
Travel Charger
RLN4884B Travel Charger
kit includes a cigarette
lighter adapter attached to
a rapid charger and
mounting bracket. Allows
radio to be used while
it is charging.
Travel Charger Mounting Bracket
0780384K84 Universal Mounting Bracket for Travel Charger. Includes
screws and nylon cord.
Travel Charger AC Transformer
Travel charger AC transformer adapts onto the cigarette lighter
adapter cord to allow it to be plugged into an AC wall outlet for
indoor use
2580600E05 Transformer 120V (US)
2580600E06 Transformer 230V (Euro)
2580600E07 Transformer 230V (U.K.)
2580600E08 Transformer 220V (Argentina)
NTN1177D
RLN4884B
8/03
Portable
Accessories
HT1000 Series
Motorola Conditioning Charger (MCC)
The MCC will help extend battery life and enhance battery operation.
It will safely condition and charge your specified nickel cadmium
(NiCd) and nickel metal hydride (NiMH) batteries in approximately
an hour.
WPLN4090BR MCC Kit,
110V AC; includes both
base unit and 7V adapter
WPLN4091BR MCC Kit,
220V AC; includes both
base unit and 7V adapter
WPPN4002BR 110V AC
Base Charge Unit Only (order
adapter plate separately)
WPPN4006AR 220V AC Base Charge Unit Only (order adapter
plate separately)
WPPN4065BR Multi-Unit Conditioning Charger Four Station Base
110V (order adapter plate separately)
WPPN4004BR 7 Volt Adapter Only
3080384G15 Cigarette Lighter Adapter Cord; MCC multi-unit
conditioning charger
RLN4814A Vehicular Mounting Bracket for single unit Motorola
Conditioning Charger
3080384M21 DC Hard wire cable for vehicular installation
(included in RLN4814A)
Battery Maintenance System plus (BMS plus)
Increase the useful life of your batteries.
Using interchangeable battery adapters (sold separately), the BMSplus
is capable of charging and discharging, analyzing, conditioning and
cycle test on batteries; tracking battery voltage and capacity (mAh).
The BMSplus offers a 3 year warranty. Its easy-to-use design supports
hundreds of 2-way, cellular, and camcorder batteries with printer
port* (Serial-RS-232C port – uses female 9-pin to male 25-pin cable).
WPLN4079BR Six-Station, 110V AC, 50/60 Hz
WPLN4080BR Six-Station, 230V AC, 50/60 Hz
WPPN4085AR BMSplus field upgrade kit for WPLN4079AR,
WPLN4080AR and WPLN4081AR allows these units to support Li Ion
battery chemistries
NDN4005B Three-station 110V AC, 50/60 Hz
NDN4006B Three-station 230V AC, 50/60 Hz
BMS plus Adapter
TDN9435C Adapter Compatible
with NiCd Batteries Only
CDN6364A Adapter Compatible
with Both NiCd and
NiMH Batteries
*Compatible with the STAR Micronics SP200 series printers, available from any STARMicronics distributor, and other printers with STAR emulation.
WPPN4002BR
WPLN4079BR
TDN9435C
8/03
Portable
Accessories
HT1000 Series
Battery Optimizing System II (BOS II)
No other battery analyzer
matches the speed,
accuracy, and versatility of
the Battery Optimizing
System II. Ideal for large
fleet, public safety, and all
other users who rely on their
battery performance. Now
with increased power, more
sophisticated programming
options, and easier to use
navigation paths, optimizing
your batteries was never
easier. Key features include:
• Support for NiCd, NiMH, Li-ion, and SLA batteries
• 100 watt power supply and programmable from 100 mAH to
4 amps per station
• Interchangeable adapters accomodate all major brands
• Includes a variety of user programs and allows for
customizable programming
• Proprietary recondition cycle restores NiCd and NiMH batteries
• Increased processing power and testing resolution – including
a three minute Quicktest that measures the batteries State of
Health (SoH)
• Printer output for reports and labels
• Three year warranty
WPLN4124AR BOS II, Four-Station, 100-240V AC (US line cord)
WPLN4125AR BOS II, Four-Station, 100-240V AC (UK/Euro line cords)
BOS II Adapter
RL-72403 Standard Adapter
impres™ Smart Energy System
The impres smart energy system ensures
maximum talk-time and optimized battery
cycle life through the use of its advanced
charging algorithm and automatic
reconditioning features. The smart energy
system reconditions impres batteries when
they need it, automatically, keeping them in
peak condition. It's advanced conditioning
features allow batteries to be safely left on
the charger for extended periods of time without incurring the
damaging heat build-up which can rob batteries of cycle life. In
addition, batteries left on the charger are kept fully charged so
they are always ready when you need them. The impres system
reconditions batteries when they need it based on their usage
pattern. Talk time and cycle life are optimized and the need for
manual maintenance programs reduced or eliminated. This rapid-
rate tri-chemistry charging system will also charge existing legacy
batteries and supports multiple radio platforms including Saber,
XTS, and HT1000 series portables.
WPLN4111AR impres Single Unit Charger
WPLN4108BR impres Multi-Unit Charger
impres™ Multi-Unit Charger with Display Modules
The impres Multi-Unit Charger with Charger Display Modules has a
two-line LCD screen for each of its six charger pockets that provides
users with a host of valuable battery information. When a calibrated
impres battery is inserted into a pocket, it provides the current
battery mAh and percent of rated capacity which allows the user to
immediately know the status of the battery without having to charge
and discharge the battery. Additionally, the unit displays the
remaining charge time (NiCd and NiMH only) which lets the user
know when the impres battery will be ready for use. Additional
information displayed includes: battery serial and part number
information, battery chemistry, voltage and charge status and the
version of the charger and display modules.
WPLN4130AR Multi-Unit Charger with Display Modules
RLN5382A Charger Display
Module for impres multi-unit
charger version 1.3 or later
RLN5591A Charger Display
Module for impres multi-unit
charger version 1.2 or earlier
(Requires unit to be sent to the
Rockford Service Center –
instruction sheet provided)
WPLN4111AR
WPLN4124AR
WPLN4130AR
8/03
Portable
Accessories
HT1000 Series
impres™ Smart Energy System
impres™ Bundle Packs
Provide significant savings on the impres products by bundling a
charger and batteries together as a smart energy system package.
RLN5265A impres™ single unit charger with two
HNN9029AR batteries
RLN5266A impres™ single unit charger with two
HNN9028AR batteries
RLN5439B impres™ multi unit charger with six
HNN9029AR batteries
RLN5440B impres™ multi unit charger with six
HNN9028AR batteries
Vehicular Charger
This 12V DC charger is ideal for
mobile customers; it charges
portable radio NiCd batteries in
rapid charge mode (in less than
3 hours) until full charge is
obtained and then switches to
trickle charge mode. A
microprocessor controls the
charge rate. This durable unit
comes with a metal mounting
bracket and is PAC-RT compatible.
TDN9816A Vehicular Charger
Carrying Accessories
Carrying Cases
A variety of carrying accessories are available for your comfort and
convenience. The carrying cases are available in sizes designed to fit
your radio & battery and permit audio to be heard clearly.
Standard Belt Loop Carrying Cases
NTN7238A Leather Carry Case with Belt
Loop and T-Strap for use with high
capacity battery
NTN7239A Leather Carry Case with Belt
Loop and T-Strap for use with ultra-high
capacity battery
NDN4018B DTMF Leather Carry Case with
Belt Loop for use with high and ultra-high
capacity batteries
NTN7247A Nylon Carry Case with Belt
Loop and Strap for use with high and
ultra-high capacity batteries
High Activity Swivel Carrying Cases
The following carrying cases have a high activity swivel “D” button
and belt loop. To remove case from belt loop, rotate case 180
degrees and slide case upward, out of the holder. Case stays on
belt more securely in high activity applications versus standard
swivel cases while allowing the radio to swing freely with
body movements.
NTN8035B Leather Carry Case with 2.5˝ High
Activity Swivel Belt Loop and T-Strap for use with
high capacity battery
NTN8037B Leather Carry Case with 3.0˝ High
Activity Swivel Belt Loop and T-Strap for use with
high capacity battery
NTN8036B Leather Carry Case with 2.5˝ High
Activity Swivel Belt Loop and T-Strap for use with
ultra-high capacity battery
NTN7247A
NTN8036A
TDN9816A
8/03
Portable
Accessories
HT1000 Series
Carrying Accessories
NTN8038B Leather Carry Case with 3.0˝ High
Activity Swivel Belt Loop and T-Strap for use with
ultra-high capacity battery
NDN4017B DTMF Leather Carry Case with 3.0˝
High Activity Swivel Belt Loop and Antenna Strap
for use with high and ultra-high capacity battery
T-Strap
NTN7782A T-Strap for leather Carry Cases
NTN7376A T-Strap for nylon carry cases
Belt Loops
NTN8039B 2.5˝ High Activity Swivel Belt Loop
NTN8040B 3.0˝ High Activity Swivel Belt Loop
NTN1534A High-activity “D” button and 2.5˝ belt loop
NTN1535A High-activity “D” button and 3.0˝ belt loop
Belt Clips
4205638V07 3˝ Belt clip
4205638V09 2.5˝ Belt clip
Belt
4200865599 1.75˝ Wide Black Belt
Carrying Strap
NTN5243A Shoulder Carry Strap,
allows easy carrying of radio in a
case when not wearing a belt
Carrying Accessories
Waterproof Bag
HLN9985B Waterproof bag includes large carrying strap
Swiveller
TDN9684A Swiveller, includes clip
button, holster and belt
Swiveller ReplacementAccessories
TDN9690A Clip button, mounts
on battery
TDN9688A Holster, compatible with all buttons
TDN9687A Belt, 2˝ nylon
Portable Radio Hanger
The portable radio hanger slides over and hangs from the door panel
in a vehicle. The radio’s belt clip slides onto the portable hanger
allowing convenient, easy mounting. Two sizes are available to fit
door panels.
TDN9327A Portable Radio Hanger
for door panels up to 2.75˝
TDN9373A Portable Radio Hanger
for door panels up to 3.25˝
Universal Holders
RLN4943A Universal holder with gooseneck bracket
RLN4944A Wheelchair quick release assembly
RLN4945A Universal holder with gooseneck bracket and wheelchair
quick release assembly
NTN8038A
4200865599
NTN5243A
TDN9684A
TDN9687A
TDN9327A
8/03
Portable
Accessories
HT1000 Series
Carrying Accessories
Chest Pack
Carry the radio mounted on chest
with adjustable straps over
shoulders and around waist.
HLN6602A Universal Chest Pack
with Radio Holder, Pen Holder, and
Velcro Secured Pouch
1505596Z02 Replacement
Strap for HLN6602A
Break-A-Way Chest Pack
All of the same features as the original chest
pack (HLN6602A) plus break-a-way tabs that
allow the entire pack to be pulled off with
approximately 10 lbs. of pressure. Perfect for
railroads, manufacturing locations,
construction sites and anywhere safety
is a concern.
RLN4570A Break-A-Way Chest Pack
RadioPAK™
RLN4815A Universal RadioPAK™
with Radio Holder. Worn around
waist with adjustable belt. Includes
attached 6˝ by 8˝ zippered pouch for
other job necessities.
4280384F89 Universal RadioPAK™
belt lengthener; fits waists larger
than 40˝
Audio Accessories
Remote SpeakerMicrophones (RSM)
Allows you to talk and listen without
removing the radio from the belt case or
charger. Ideal for high noise
level environments. These water
resistant microphones include coil cord
assembly, 3.5mm earjack, swivel
clothing clip and quick disconnect latch.
*NMN6193C Remote Speaker
Microphone
*NMN6191C Noise Cancelling Remote
Speaker Microphone
0104010J46 Replacement Coil Cord Cable Assembly for Remote
Speaker Microphones
RLN5002A MicJacket Kit; compatible with NMN6191 and
NMN6193 remote speaker microphones
Public Safety Speaker Microphones (PSM)
Public Safety Speaker Microphones include straight cord assembly,
3.5mm earjack, swivel clothing clip, quick disconnect latch, antenna
connector, receiver, and audio high/low volume push button. Antenna
must be ordered separately. Use radio antennas on page 162.
*NMN6228C 30˝ Noise-Cancelling Public Safety
Speaker/Microphone, straight cord
*NMN6243B 18˝ Noise-Cancelling Public Safety
Speaker/Microphone, straight cord
*NMN6244B 24˝ Noise-Cancelling Public Safety
Speaker/Microphone, straight cord
0104004J29 30˝ Public Safety Microphone Cable
0104004J46 18˝ Public Safety Microphone Cable
0104004J47 24˝ Public Safety Microphone Cable
REX4410C PTT Paddle Replacement Lit for Remote and Public
Safety Microphones
RLN5004A MicJacket Kit; compatible with NMN6228, NMN6243
and NMN6244 remote speaker microphones
* Intrinsically safe
HLN6602A
RLN4570A
NMN6193B
8/03
Portable
Accessories
HT1000 Series
Audio Accessories
RSM Accessories
Epaulet Strap
Black leather epaulet strap secures
remote speaker microphone to epaulet
straps on shirt or jacket and
accommodates back clip in leather cut-
outs. Snap closure secures remote
speaker microphone cord to allow reliable
communications in hostile environments.
RLN4294A Epaulet Strap, Velcro
RLN4295A Epaulet Strap, small clip
Audio Accessories for the RSM
Plugged into the 3.5mm earjack on the RSM audio adapter, these
audio accessories will mute the speaker on the RSM allowing the
user to discretely hear all incoming messages. Ideal for noisy
environments. The following audio accessories can also be plugged
directly into the radio with the BDN6676D audio adapter.
BDN6781A Pellet Style Earpiece
BDN6719A Flexible Ear Receiver
Headsets for the RSM and PSM
RMN4056A Receive-Only Dual Muff
Headband Style Headset; provides
24dB of noise reduction; for use with
all Remote and Public Safety
Microphones with a 3.5mm threaded
jack (can be plugged directly into
radio with BDN6676D adapter)
RMN4057A Receive-Only Hardhat
Mount mounts easily to hardhats
with slots and provides 22dB of noise
reduction; for use with all Remote
and Public Safety Microphones with
a 3.5mm threaded jack (can be
plugged directly into radio with
BDN6676D adapter)
Audio Accessories
CommPort: Integrated Microphone/Receiver System
CommPort system contains a
miniature microphone and receiver,
and connects to your two-way radio,
making it possible to hear and speak
under the most adverse conditions.
*NTN1624A Integrated Ear
Microphone/Receiver System
w/Palm PTT (includes BDN6676D
3.5mm Jack Adapter)
*NTN1625A Integrated Ear
Microphone/Receiver System with
PTT on radio adapter (includes
BDN6676D 3.5mm
Jack Adapter)
*NTN1663A Integrated Ear
Microphone/Receiver System
w/Ring PTT (includes BDN6676
3.5mm Jack Adapter)
*NTN1736A CommPort integrated
microphone/receiver with snap on side
push-to-talk (PTT)
*NNTN4186A Integrated Microphone/Receiver
with Body Push-to-talk Button
NKN6510A Replacement Cable for NTN1624
NKN6508A Replacement Cable for NTN1625
NKN6512A Replacement Cable for NTN1663
NKN6525A Replacement cable with snap on
side PTT
NNTN4188A Replacement Remote Push-to-Talk
Body Switch
NTN8821A CommPort Maintenance Kit, Includes
Replacement Ear Tubes (Quantity 10), Windscreens
(Quantity 2) and Microphone Seal Strips (Quantity 10)
NTN8986A Adhesive Pads (Quantity 90) for secure
attachment to ear
NTN8988A Ear Straps (Quantity 10), for secure
attachment to ear
4285838B01 Replacement Collar Clip
4202006A01 Replacement Back Cover Clip
RLN5037A Replacement Ear tubes (Quantity 10)
* Intrinsically safe
RLN4294A
RLN4295A
RMN4056A
NTN1623A
NTN1625
8/03
Portable
Accessories
HT1000 Series
Audio Accessories
Surveillance Accessories
Surveillance accessories allow the user to privately receive
communications with the earpiece and are ideal when environments
require discrete communications.
The following surveillance accessories require the BDN6676D
(3.5 mm threaded adapter jack) that attaches to the radio, unless
being used with speaker/microphone.
Receive-only Surveillance Kit (1 Wire)
*BDN6664A Beige
*BDN6665A Beige
BDN6726A Black
BDN6727A Black
Receive-only Surveillance Kit
with Volume Control (1 Wire)
*BDN6666A Beige
BDN6728A Black
Surveillance Kit with
Microphone and Push-To-Talk
Combined (2 Wire)
*BDN6667A Beige
*BDN6669A Beige
BDN6729A Black
BDN6731A Black
Surveillance Kit with
Microphone and Push-To-Talk
Separate (3 Wire)
*BDN6668A Beige
*BDN6670A Beige
BDN6730A Black
BDN6732A Black
*BDN6676D 3.5mm Jack
Adapter with Quick Disconnect
Latch
Audio Accessories
Surveillance Kit Replacement Accessories
5080369E38 Standard Earpiece Assembly, includes earphone,
earloop and eartip, beige
5080370E90 Standard Earpiece Assembly includes earphone, earloop
and eartip, black
5080369E39 Extra Loud Assembly, includes
earphone, earloop and eartip, beige
5080370E91 Extra Loud Earpiece
Assembly, includes earphone, earloop
and eartip, black
5080369E40 Plastic Urethane
Earloop, beige
5080370E92 Plastic Urethane
Earloop, black
5080371E73 Standard Rubber Eartip, beige, pack of 25
5080371E75 Standard Rubber Eartip, black, pack of 25
5880377E06 Plastic Eartip Adapter, pack of 10
Surveillance Kits with Extended Wear Earpiece
These kits include a comfort earpiece with a rubber ear tip and and a
clear comfortable acoustic tube. Users can hear transmissions
clearly, while the clear tube provides a discreet appearance.
RLN5311A Beige Two-Wire Comfort
Earpiece with Combined Microphone
and Push-to-Talk; requires BDN6676D
audio adapter
RLN5312A Black Two-Wire Comfort
Earpiece with Combined Microphone
and Push-to-Talk; requires BDN6676D
audio adapter
RLN5313A Receive-Only Comfort
Earpiece, black
RLN5314A Receive-Only Comfort
Earpiece, beige
* Intrinsically safe
BDN6667A
BDN6666A
BDN6664A
BDN6668A
5080370E92
5080369E39
RLN5311A
8/03
Portable
Accessories
HT1000 Series
Audio Accessories
Completely Discrete Earpiece
Remain discretely in touch with this miniaturized receiver. All
messages received through the user’s two-way radio are inductively
relayed to the wireless earpiece in the user’s ear. Inductive neckloop
is easily hidden under the user’s clothing for covert operations.
Neckloop attaches to the user’s Motorola Surveillance Kit providing
completely discrete two-way communications. Security operatives,
public safety officials, and private investigators can communicate
with ease without any visible equipment. Small as it is, it offers a
full range of audio functions including automatic squelch, automatic
gain control and noise filtering. Must be used in conjunction with a
Motorola Surveillance Kit. Just remove the earpiece on any standard
2- or 3-wire surveillance kit and plug in the neckloop for completely
discrete communication.
RLN4922A Completely Discrete Earpiece Kit; includes wireless
earpiece, inductive neckloop, 6 spare batteries and 5 spare
ear wax guards
RLN4919A Ear
Wax Guards,
5 per pack
RNN4005A 1.4V
Battery, 6 per pack
Audio Accessories
Noise Kits
Lightweight translucent tube attaches to
Motorola surveillance accessories. Clothing
clip prevents the accessory from being
pulled from the ear due to body movement
or head rotation.
NTN8370A Extreme Noise Kit, includes 2
foam earplugs for loud environments,
provides 24dB noise protection
NTN8371A Low Noise Kit, includes rubber
eartip for low noise environments
5080384F72 Replacement Foam Plugs; pack of 50
(for use with NTN8370A)
5080371E73 Replacement Standard Rubber Eartips; pack of 25
(for use with NTN8371A), beige
Clear Comfortable Earpiece
The clear comfortable
earpiece forms to the inside
of your ear and is perfect
for low noise environments.
Compatible with the
NTN8371A, clear acoustic
tube assembly, and most
surveillance kits (1-, 2- and
3-wire). This earpiece is
made of easy-to-clean
chemically inert,
hypoallergenic
material.There are 3 items
needed to make this
product work:
1. Clear Comfortable
Earpiece
2. Clear Acoustic Tube
Assembly (NTN8371A)
3. Surveillance Kits
RLN4760A Small Custom Earpiece, right ear
RLN4763A Small Custom Earpiece, left ear
RLN4761A Medium Custom Earpiece, right ear
RLN4764A Medium Custom Earpiece, left ear
RLN4762A Large Custom Earpiece, right ear
RLN4922A
NTN8370A
Acoustic Tube)
with Earphone
Optional)
Clear Comfortable Earpiece)
Order Separately
Noise Attenuating Plugs)
NRR24dB Included)
with NTN8370A
Standard Rubber)
Eartip Included with)
NTN8371A
8/03
Portable
Accessories
HT1000 Series
Audio Accessories
Ear Microphone System (EMS)
This compact unit picks up the voice through bone vibrations in the
ear canal. The miniature earpiece leaves the hands free and face
unobscured when worn by rescue and hazard protection personnel,
who still retain the ability for direct hearing and speaking. For
personnel required to wear breathing apparatus, communications
with protective masks are as clear as communications without. And
its high speech clarity under noisy environments makes it ideal for
high noise environments. Available in PTT or Voice Activated (VOX).
Interface Module needs to be ordered separately for EMS
to work.
*BDN6677A Ear Microphone for Standard
Noise Levels (up to 95dB, black)
*BDN6678A Ear Microphone for Standard
Noise Levels (up to 95dB, beige)
*BDN6641A Ear Microphone
for High Noise Levels (up to 105dB)
Interface Module For EMS
*BDN6708B Push-To-Talk Interface Module
*BDN6671B Push-To-Talk or Voice-
Activated Interface Module
Audio Accessories
Optional Accessories For EMS
*0180358B38 Remote Push-
To-Talk Ring Switch
0180300E83 Remote Push-
To-Talk Body Switch
0180300E25 Earguard with
Adjustable Loop; secures ear mic in ear
0180358B32 Earholder, black size small;
secures ear mic in ear
0180358B33 Earholder, black, size medium;
secures ear mic in ear
0180358B34 Earholder, black, size large;
secures ear mic in ear
0180358B35 Earholder, clear, size small;
secures ear mic in ear
0180358B36 Earholder, clear, size medium;
secures ear mic in ear
0180358B37 Earholder, clear, size large;
secures ear mic in ear
4280369E44 Replaceable Belt Clip with Screws
5080358B28 Eartips, black, size medium (10 per pack)
5080358B29 Eartips, black, size large (10 per pack)
5080358B30 Eartips, beige, size medium (10 per pack)
5080358B31 Eartips, beige, size large (10 per pack)
Flexible Ear Receiver
The flexible ear receiver contains a
flexible earloop and speaker, and
rests external to the ear.
BDN6719A Ear Receiver with
3.5 mm Threaded Plug, requires adapter
BDN6676D unless being used with speaker
microphone
7580372E11 Replacement Foam
Ear Cushions for BDN6719A
* Intrinsically safe
BDN6641A
Shown with
interface module
BDN6708B
0180358B38
0180358B33
BDN6719A
8/03
Portable
Accessories
HT1000 Series
Audio Accessories
Pellet Style Earpieces
BDN6780A Single Earbud with
Microphone and Push-To-Talk,
requires adapter BDN6676D, unless
being used with speaker microphone
BDN6781A Single Earbud, receive
only; requires adapter BDN6676D
unless being used w/speaker
microphone
7580372E70 Replacement Foam Ear Cushion for Pellet Earpieces
Lightweight Headsets
Lightweight headsets allow for high clarity, hands-free, discrete
two-way communication, while adding comfort necessary for
extended wear in moderate noise environments. Requires BDN6676D
Audio Adapter.
*NMN6245A Single Muff Adjustable Lightweight Headset with
Boom Microphone and In-line Push-To-Talk Switch (requires
BDN6676D adapter)
*NMN6246B Ultralite Headset with Boom Microphone and
In-line Push-To-Talk Switch; ear bud style receiver (requires
BDN6676B adapter)
*NMN1020A Lightweight Headset with Boom Microphone to be
worn on a helmet or safety glasses. Includes NKN6498A adapter
cable. Requires BDN6676D adapter. FM approved.
*NKN6498A Headset Adapter Cable for use with NMN1020A
REX4648A Replacement Foam Earpad and Windscreen Kit
for NMN6245A
5080574E02 Foam Earpads for use with NMN6245A, 10 per pack
Audio Accessories
Temple Transducer
The Temple Transducer represents a significant achievement in
headset design and functionality. It allows the user to receive audio
without covering the ear. The receiver portion of the accessory rests
on the temples and it is capable of converting the receive audio from
a two-way radio into sound vibration. The sound vibration is
transmitted through the surrounding human tissue and bone directly
into the inner ear where it is received by the user. It features an in-
line PTT and noise canceling
boom microphone. The Temple
Transducer enhances
communications and safety by not
impairing the user's hearing of
external sound environment, such
as from machinery and equipment,
warning and fire alarms, the
intercom, traffic, and even
casual conversations with their
co-workers.
*RMN4049A Temple Transducer
Racing Headset
Motorola is the Official Wireless Equipment supplier of CART, so
whether your customers’ playing field is a racetrack, construction
site or other challenging environment, they can count on this Racing
Headset for superior comfort and dependable operation.
RMN5015A Racing Headset
(Requires radio adapter
cable BDN6673B)
* Intrinsically safe
BDN6780A
RMN4049A
RMN5015A
8/03
Portable
Accessories
HT1000 Series
Audio Accessories
Medium Weight Headsets
Medium Weight Headsets offer high-clarity sound with the
additional hearing protection necessary for providing consistent,
clear two-way radio communications in harsh, noisy situations.
*NMN6258A Medium Weight
Headset, over the head with
In-Line PTT, Noise Reduction
Rating = 24dB
*NMN6259A Medium Weight
Headset, behind the head with
In-Line PTT, Noise Reduction
Rating = 24dB
7580376E34 Replacement Foam
Earseals, 1 pair
1580376E32 Replacement Cloth Covers for Earseals, 1 pair
5080548E02 Replacement Windscreen for Boom Microphone
3280376E35 Replacement “O”-ring for Windscreen
4204004K01 Replacement Adjustable Headstrap for NMN6259A
RMN4051A Hardhat Mount Headset mounts easily to hardhats with
slots and provides 22dB of noise reduction; requires RKN4095A
adapter cable, hardhat not included
RKN4095A Radio Adapter Cable with In-Line PTT for
use with RMN4051A
Tactical Medium Weight Headsets
Same high-clarity sound and additional hearing protection as our
standard medium weight headsets while including two microphones
on the outside of each earcup which reproduces the ambient sound
back into the headset. Harmful
sounds are suppressed to a safe
level and low sounds are amplified
up to 5 times but never more than
82dB. Includes on/off volume control
on ear cups.
RMN4052A Tactical Headband
Style Headset, grey; provides 24dB
of noise reduction and requires
RKN4095A adapter cable
Audio Accessories
RMN4053A Tactical Hardhat Mount Headset mounts easily to
hardhats with slots; provides 22dB of noise reduction and requires
RKN4095A adapter cable, hardhat not included
RKN4095A Radio Adapter Cable with IN-Line PTT for use with
RMN4051A and RMN4053A
RLN4923A Two Replacement Snap-in Earseals; Recommended
replacement interval is once every six months to ensure constant
level of attenuation hygiene and comfort for RMN4051A,
RMN4052A, and RMN4053A.
Heavyduty Headsets
Heavyduty headsets include noise-cancelling boom microphones and
can be worn with or without a hardhat. The Push-To-Talk switch is
located on the earcup. The VOX module is contained within the
headset on voice activated units. Heavyduty headsets require
radio adapter cable BDN6673B, to be ordered separately.
*BDN6645A Push-To-Talk Headset with
Boom Microphone; requires adapter
cable BDN6673B; noise reduction
rating=24dB
*BDN6635B Voice-activated Headset
with Boom Microphone; requires
adapter cable BDN6673B; noise
reduction rating=24dB
*BDN6636B Voice-activated
Headset with Throat Microphone;
requires adapter cable BDN6673B;
noise reduction rating=24dB
*BDN6673B Radio Adapter Cable
* Intrinsically safe
NMN6258A
RMN4052A
BDN6645A
BDN6636B
BDN6635B
8/03
Antennas
HT1000 Series
Portable Antennas
Flexible Whip Antennas
Antenna has a one-piece finish and steel core for optimal strength
and better radiation characteristics. Provides more comfort when
radio is worn on the belt.
8505241U05
Flexible Whip, 403-520MHz, 6˝
8505241U03
Flexible Whip, 806-870MHz, 7˝
8505241U04
Flexible Whip, 896-941MHz, 7˝
Helical Antennas
Helical are sturdy and dependable for
years of failsafe communication. Each
antenna is designed and built to quality
standards. The skirt at the base of the
connector helps to seal out damaging
elements. Connector is made of plated
brass material for long life.
8505644V01
Helical, 136-151MHz, 6˝
8505644V02
Helical, 151-162MHz, 6˝
8505644V03
Helical, 162-174MHz, 6˝
8505644V04
Helical, 403-435MHz, 3˝
8505644V05
Helical, 435-470MHz, 3˝
8505644V06
Helical, 470-520MHz, 3˝
Portable Antennas
Dipole Antennas
Dipole molded antennas are injection molded
in lasting polyurethane. The wide skirt at the
bottom of the connector protects against
damaging environmental elements. The
dipole antenna is ideal when strong and
solid signal clarity is demanded.
NAF4000B
Dipole, 806-869MHz, 8˝
8505884R02
Dipole, 896-941MHz, 8˝
Wideband Antenna
Wideband antenna is ideal when radio is used in different
frequencies since one antenna will cover all ranges.
8505518V01 Wideband, 136-174MHz, 6˝
Stubby Antenna
This quarterwave stubby antenna is ideal
when radio is worn on the belt because the
short antenna is non-obtrusive. This is a
broadband antenna that can be used for
both 800MHz and 900MHz applications.
8505241U06*
Stubby, 806-941MHz, 4˝
*8505241U06 is a broadband antenna that operates in the 800/900 MHz band
8505644V01
8505644V04
8505241U05
8505644V03
8505241U06
NAF4000B
8505884R02
8/03
Miscellaneous
Accessories,
Batteries
HT1000 Series
Miscellaneous Accessories
Replacement Kit
REX4398A 2/8/16 Channel Cosmetic Replacement Kit
Public Safety Tilt Switch
An external emergency switch that is activated when the unit is
tilted at a greater than 60 degree angle. Delay times are factory
programmed for 8 seconds and are not field programmable. The
emergency feature must be programmed into the radio to enable the
tilt switch option. FM approved. Not compatible with the JT1000.
NTN7660A Public Safety Tilt Switch
Portable Batteries
Nickel-Cadmium Premium
Part Number: NTN7143CR
Volts: 7.5
Avg. mAh: 1200
Height: 6˝
Intrinsically Safe: No
Part Number: NTN7144CR
Volts: 7.5
Avg. mAh: 1500
Height: 6˝
Intrinsically Safe: No
Part Number: NTN7146AR
Volts: 7.5
Avg. mAh: 1200
Height: 6˝
Intrinsically Safe: Yes
Part Number: NTN7147AR
Volts: 7.5
Avg. mAh: 1300
Height: 6˝
Intrinsically Safe: Yes
Part Number: NTN7149BR
Volts: 7.5
Avg. mAh: 1300
Height: 6˝
Intrinsically Safe: Yes
CSA: Yes
Part Number: NTN7150AR
Volts: 7.5
Avg. mAh: 1200
Height: 6˝
Intrinsically Safe: Yes
MSHA: Yes
NTN7143CR
NTN7147AR
8/03
Batteries,
Service Aids
HT1000 Series
Portable Batteries
Part Number: NTN7341AR
Volts: 7.5
Avg. mAh: 1400
Height: 6˝
Intrinsically Safe: Yes
Part Number: NTN7372AR
Volts: 7.5
Avg. mAh: 1200
Height: 6˝
Intrinsically Safe: Yes
Nickel Metal Hydride Premium
Part Number: WPNN4013A
Volts: 7.5
Avg. mAh: 2000
Height: 6˝
Intrinsically Safe: No
Part Number: WPNN4037A
Volts: 7.5
Avg. mAh: 1900
Height: 6˝
Intrinsically Safe: Yes
Nickel-Cadmium impres™
Part Number: HNN9028AR
Volts: 7.5
Avg. mAh: 1500
Height: 6˝
Intrinsically Safe: No
Part Number: HNN9029AR
Volts: 7.5
Avg. mAh: 1500
Height: 6˝
Intrinsically Safe: Yes
Service Aids
Cloning Cable
Allows another radio to be duplicated from a master radio by
transferring programmed data from one radio to another.
RKN4036D Cloning Cable
Radio Interface Box
Links radio programming cable and
computer interface together. Provides
required voltage shift to enable
communications between radio and
computer. Requires computer
interface cable, radio test and
programming cable, and 9 volt snap
type battery (6082728J01), order separately.
RLN4008E Radio Interface Box
Computer Interface Cable
Used to connect
computer’s serial adapter
to Radio Interface Box.
3080369B71 Cable, RIB to
25 pin D
3080369B72 Cable, RIB to
9 pin D
Radio Test and Programming Cable
Used with Portable Radio Test Set, RTX4005B, for transmitter,
receiver alignment and performance checks. Also used in
programming radio.
RKN4035D Radio Test and Programming Cable
Wall Mounted Power Supply
Used to supply power to radio
interface box RLN4008E
0180357A57 Wall Mounted Power
Supply, 110 Volts
0180358A56 Wall Mounted Power
Supply, 220 Volts
NTN7372AR
WPNN4013A
RLN4008E
0180357A57
3080369B71
8/03
Service Aids,
Manuals
HT1000 Series
Service Aids
Battery Eliminator
RLN1014A The Battery Eliminator acts
like a battery with a cable to access a DC
external power supply. It is ideal to
inspect transmitters and receivers on
incoming radios. Reverse supply polarity
protection and input fuse protection
are provided.
Programming Software
Utilizing your personal computer, this software enables you to add or
reprogram frequencies as your requirements change. Requires
interface box and appropriate cables, must be ordered separately.
RVN4098H Programming Software
Option Boards
NTN8313A Analog Voice Scrambler Advantage Board, for use
with HT1000 only. NOT APPROVED for installation in FM
approved models.
Manuals
6881200C15 HT1000/JT1000/MT2000 & MTX8000/9000
Radio Theory
6881200C40 HT1000/JT1000 & MT2000 Service Manual
6881200C25 MTX8000/9000 Service Manual
6881079C50 HT1000 Operator’s Manual
6881078C45 JT1000 Operator’s Manual
6881076C65 MT2000 Operator’s Manual
6881072C10 MTX8000/9000 B3 Operator’s Manual
6881072C40 MTX8000/9000 B5/B7 Operator’s Manual
0180305J46 Ear Microphone System and Temple
Transducer CD-ROM
0180305J70 impres™ System CD-ROM
RLN1014A