Book of Full Text

IESKO 2019VI. International Earthquake Symposium Kocaeli 2019

September 25-27, 2019, Kocaeli, Turkey

Paper Title (English)

Name Surname1*, Name Surname 2+ and Name Surname 3

1Department/Research Institute, University, City, Country2Department/Research Institute, University, City, Country3Department/Research Institute, University, City, Country

*Corresponding author: e-posta@xxx.com+Speaker: e-mail@yyy.edu

Presentation Type: Oral / PosterPresentation Language : English

AbstractThis document presents the formatting instructions for the “Full Text” of the “VI. International Earthquake Sympossium Kocaeli 2019” This document can serve as the base template for a Microsoft Word based typesetting system. The abstract of a research paper within the scope of this symposium should be is a succinct summary of the article's purpose, main points, method, findings, and conclusions. The length of the abstract should be a minimum of 200 and a maximum of 400 words. Please carefully check it from the world count option from word processors. The full text could be written in English and Turkish. If you want to write full text in Turkish, you have to add an English abstract. The title of the paper should be 14-point, name-surname 12-point and affiliations 10-point. The text should be single spaced in 12-point Times New Roman. Do not include scientific symbols, tables, lists, figures and photos in the abstract, please add this to the Introduction or Methodology parts. The full text should be confined within a single paragraph. We recommend that you download these directions as a MS Word document and use it as the template for your full text as it contains all necessary formats and styles. Full text papers (min. 3 pages-max 4 pages) should cover one or more of the conference tracks. The full-text should be written in MS Word and should be sent as an attachment to the “https://kongresistemi.com/iesko2019” portal as a "doc" or "docx" file which will be activated from 16 July 2019 to 01 September 2019.

1. IntroductionThis document represents a template for the symposium It could be downloaded from the web site “https://iesko2019.org/” submission section. We recommend that authors have their "full teext" checked by an English language native speaker before submission. In the Introduction part, the theoretical basis of the study in the literature should be discussed. The citations you make from different sources must be given and added in the references. For citations of references in the text we prefer the use of "surname, brackets, and years". For example: Ulutaş and Gürleme (2018). The deadline for submitting of the full texts is 1 September 2019.

2. Materials and MethodYou should describe in detail the materials and methods used Describe in detail the materials and methods used to conduct the study. It is not an obligation for only describe "materials and methods". you can describe the details with your own headings and subheadings.

2.1. Figures and TablesFigures and tables should be embedded and not suplied separately. Figures and tables must be centered in the column. Large figures and tables may span across both columns. Any table or figure that takes up more than 1 column width must be positioned either at the top or at the bottom of the page. The minimum resolution of the figures or photos should be at least 300 dpi.

Fig. 1. A figure caption is always placed below the illustration. Short captions are centered, while long ones are justified (Times New Roman10).

2.2. Page numbersPage numbers, headers and footers must not be used

3. Equations

Displayed equations are left aligned and set on a separate line with equation number in brackets.

(1)

Table 1. Table captions should be placed above the tables (Times New Roman10).

Eq. Parameters Calculations

Mw 7.5

Focal depth (km) 25.0

Strike/Dip/Rake ( 0 ) 310/35/100

Average slip (m) 3.0

Fault Lenght (km) 85

Fault Width (km) 30

4. Results, Conclusions and/or Discussions

You can summarize and discuss your study. You can summarized your study in results, conclusions and discussions or both of them. Results should be clear and concise. In discussion part you should explore the significance of the results of the work, not repeat them.

AcknowledgementYou can thank to some respected persons and point out financial support for doing your work in this section. Appreciativeness may be mentioned in this section due to valuable comment suggestions on your paper which gave you an inspiration to improve the quality of the study. The heading of the acknowledgment must not be numbered.

References

All reference items must be in 10 punto Times New Roman. Any reference to a paper within the text should be made by the last name of the author and the year of the work such as (Sertçelik, 2010) or (Sertçelik et al., 2018). The references should be listed by the last names of the authors. Here is the examples for different type of references,

example of a journal article in

Ulutaş, E., 2013. Comparison of the seafloor displacement from uniform and non-uniform slip models on tsunami simulation of the 2011 Tohoku–Oki earthquake. Journal of Asian Earth Sciences, 62, 568-585, doi:10.1016/j.jseaes.2012.11.007.

Ulutas, E., Inan, A., Annunziato, A., 2012. Web-based Tsunami Early Warning System: a case study of the 2010 Kepulaunan Mentawai Earthquake and Tsunami. Natural Hazards and Earth System Sciences, 12, 1855-1871, doi:10.5194/nhess-12-1-2012.

Example of a Thesis in

Ulutaş, E., 2006. Seismic zonation of Eastern Marmara Region, seismic microzonation of Kocaeli province and Izmit urban area, PhD Thesis, Institute of Science Technology, Kocaeli University, Kocaeli, Turkey, 235p

Example of a book in

Haykin, S., and Van VeenB., 1998. Signals and Systems, New York: Wiley.

Example of a web page in

United States Geological Survey (USGS). Earthquake Hazards Program. Global CMT Project Moment Tensor Solution. <http://earthquake.usgs.gov/earthquakes/eqinthenews/2010 > (accessed in 2011b).

Example of a technical report in Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specification, IEEE Std. 802.11, 1997.