Practical Examination Subject: Geometric Modeling Time: 2.00 Hrs Marks: 50 Class: S.E. (Mechanical) Examination Seat No: _______________________________________________________________________ Instructions:

1. Using suitable geometric modeling software solve the questions. 2. Take printout for question number 1&2. 3. Submit attached (a) Question paper (b) printout pages to the supervisor. 4. Write Examination seat number in printout page as well

_______________________________________________________________________ Q 1 Create the model as per the dimensions given in following figure 1 30 marks

Figure 1

Q 2 Create the model as per the dimensions given in following figure 2 and create the assembly using suitable constrains. 20 marks

figure 2

Practical Examination Subject: Geometric Modeling Time: 2.00 Hrs Marks: 50 Class: S.E. (Mechanical) Examination Seat No: _______________________________________________________________________ Instructions:

1 Using suitable geometric modeling software solve the questions. 2 Take printout for question number 1&2. 3 Submit attached (a) Question paper (b) printout pages to the supervisor. 4 Write Examination seat number in printout page as well

_______________________________________________________________________ Q1 Create the model as per the dimensions given in following figure 1. 30 marks

Figure 1

Q 2 Create the model as per the dimensions given in following figure 2 and create the assembly using suitable constrains. 20 marks

Figure 2

Practical Examination

Subject: Geometric Modeling Time: 2.00 Hrs Marks: 50 Class: S.E. (Mechanical) Examination Seat No: _______________________________________________________________________ Instructions:

1 Using suitable geometric modeling software solve the questions. 2 Take printout for question number 1&2. 3 Submit attached (a) Question paper (b) printout pages to the supervisor. 4 Write Examination seat number in printout page as well

Q1 Create the model as per the dimensions given in following figure 1. 30 marks

Figure 1

Q 2 Create the model as per the dimensions given in following figure 2 and create the assembly using suitable constrains. 20 marks

Figure 2

Practical Examination Subject: Geometric Modeling Time: 2.00 Hrs Marks: 50 Class: S.E. (Mechanical) Examination Seat No: _______________________________________________________________________ Instructions:

5 Using suitable geometric modeling software solve the questions. 6 Take printout for question number 1&2. 7 Submit attached (a) Question paper (b) printout pages to the supervisor. 8 Write Examination seat number in printout page as well

_______________________________________________________________________ Q1 Create the model as per the dimensions given in following figure 1. 30 marks

Figure 1

Q 2 Create the model as per the dimensions given in following figure 2 and create the assembly using suitable constrains. 20 marks

Figure 2

Practical Examination Subject: Geometric Modeling Time: 2.00 Hrs Marks: 50 Class: S.E. (Mechanical) Examination Seat No: _______________________________________________________________________ Instructions:

9 Using suitable geometric modeling software solve the questions. 10 Take printout for question number 1&2. 11 Submit attached (a) Question paper (b) printout pages to the supervisor. 12 Write Examination seat number in printout page as well

_______________________________________________________________________ Q1 Create the model as per the dimensions given in following figure 1. 30 marks

Q 2 Create the model as per the dimensions given in following figure 2 and create the assembly using suitable constrains. 20 marks

Figure 2

Practical Examination Subject: Geometric Modeling Time: 2.00 Hrs Marks: 50 Class: S.E. (Mechanical) Examination Seat No: _______________________________________________________________________ Instructions:

13 Using suitable geometric modeling software solve the questions. 14 Take printout for question number 1&2. 15 Submit attached (a) Question paper (b) printout pages to the supervisor. 16 Write Examination seat number in printout page as well

_______________________________________________________________________ Q1 Create the model as per the dimensions given in following figure 1. 30 marks

Figure 1

Q 2 Create the model as per the dimensions given in following figure 2 and create the assembly using suitable constrains. 20 marks

Figure 2