Panel Mount LED Indicators 2016 - Powell Electronics Inc · Q, QRM,QRM-NV & QS Series Selection...
Transcript of Panel Mount LED Indicators 2016 - Powell Electronics Inc · Q, QRM,QRM-NV & QS Series Selection...
Panel Mount LED Indicators 2016
PANEL SWITCHES PCB SWITCHES JOYSTICKS SWITCH PANELS LED INDICATORSwww.apem.com
www.apem.com
Q, QRM,QRM-NV & QS Series Selection Guide
2APEM
Q6 Series Q8 Series
Q12 Series Q14 Series
Q16 Series Q19 Series
Q22 Series QRM Series
• Panel mount Ø6mm• Red, green, yellow, blue, white & orange LED• Bi-color & super bright LED• Prominent, recessed & flush bezels• Bright/black chrome or satin grey finish• 7 types of termination• Panel sealed to IP67 • Voltage 2VDC to 28VAC/DC
• Panel mount Ø8mm• Red, green, yellow, blue, white & orange LED• Bi/Tri-color & super bright LED• Prominent, recessed & flush bezels• Bright/black chrome or satin grey finish• 8 types of termination• Panel sealed to IP67• Voltage 2VDC to 220VAC
• Panel mount Ø12mm• Red, green, yellow, blue, white & orange LED• Bi/Tri-color & super bright LED• Prominent bezel• Bright/black chrome or satin grey finish• 7 types of termination• Panel sealed to IP67• Voltage 2VDC to 220VAC
• Panel mount Ø14mm• Red, green, yellow, blue, white & orange LED• Bi/Tri-color & super bright LED• Prominent, recessed & flush bezels• Bright/black chrome or satin grey finish• Custom engraving options• Panel sealed to IP67• Voltage 2VDC to 220VAC
• Panel mount Ø16mm• Red, green, yellow, blue, white & orange LED• Bi/Tri-color & super bright LED• Prominent & flush bezels• Bright/black chrome or satin grey finish• Secret until lit & engraving options• Panel sealed to IP67• Voltage 2VDC to 220VAC
• Panel mount Ø19mm• Red, green, yellow, blue, white & orange LED• Bi/Tri-color & super bright LED• Prominent & flush bezels• Bright/black chrome or satin grey finish• Custom engraving options• Panel sealed to IP67• Voltage 2VDC to 220VAC
• Panel mount Ø22mm• Red, green, yellow, blue & white LED• Bi/Tri-color & super bright LED• Prominent & flush bezels• Bright/black chrome or satin grey finish• Custom engraving options• Panel sealed to IP67• Voltage 2VDC to 220VAC
• Rear Panel Mount Ø6 & Ø8mm• Red, green, yellow, blue & white LED• Bi/Tri-color, hyper bright LED• Protected bezel• Black chrome finish• 2 types of termination• Panel sealed to IP67• Voltage 2VDC to 28VAC/DC
• Rear Panel Mount Ø8mm• NVIS Green A & B,Yellow, Red, & White• NVIS compliant to MIL Std 3009• Protected bezel• Black chrome finish• 2 types of termination• Panel sealed to IP67• Voltage 2VDC to 28VAC/DC
QRM-NV Series QS Series
• 6 LED colors• 2VDC to 220VAC• Snap in LED indicators• Push on tab or wire terminals• Panel mount Ø6, Ø8, Ø10 & Ø12mm
For typical replacement of filament and neonindicators, offering long service life & high reliability.
Pages 3 to 7 Pages 8 to 12
Pages 13 to 16 Pages 17 to 21
Pages 28 to 32
Pages 38 to 46
Pages 51 to 54
Pages 22 to 27
Pages 33 to 37
Pages 47 to 50
www.apem.com
Q6 SERIES Ø6mm (.236") Panel Mount LED Indicators
3APEM
Distinctive featuresPanel mount LED indicators with 3mm colored diffused epoxy lensor 3mm water clear super bright LEDs. Bright chrome, black chrome or satin grey bezel finish. Prominent, recessed and flush bezel styles. Voltage: 2VDC - 28VDC.Terminals: 2.0 x 0.5 solder lug/fastons, pins or 200mm long wires.IP67 sealing option (EN60529).Supplied with fixing nut and spring washer.
Typical ApplicationsProcess Controls Professional Electrical Appliances Communications, Radar Civil engineering vehicles, trucks, diggers, crane Trains HVAC, Energy Management Lifts Machine Tools
www.apem.comAPEM
Features
•
6mm panel mounting LED indicator•
3mm colored diffused epoxy lens or 3mm water clear super bright LEDs•
•
Prominent, recessed and flush bezel styles• 2VDC – 28VDC•
(2.0 x 0.5) solder lug terminals, pins or (200mm long) wire terminations•
IP67 sealing option (EN60529)•
Supplied with fixing nut and spring washer
NB: UL Recognized Component
Q SERIES Ø6mm (.236") Panel Mount LED Indicators Distinctive features and specification
PANEL CUTOUT
Ø 6.00 +0.15/-0.0
Standard LED Intensity Prominent and Recessed Flush Forward Voltage HE Red 40mcd 10mcd 2.0V Green 40mcd 8mcd 2.2V Yellow 30mcd 8mcd 2.1V Blue 1,200mcd 100mcd 3.8V White 1,200mcd 220mcd 3.8V Orange 60mcd 10mcd 2.0V Bi-color (Typical) (Red/Green) 20/15mcd 10/8mcd 2.0V/2.2V
The color is changed by reversing the polarity of the supply voltage.
Super Bright LED Prominent and Recessed Flush Forward Voltage HE Red 3,500mcd 500mcd 2.2V Green 2,000mcd 350mcd 3.5V Yellow 900mcd 140mcd 2.3V Blue 2800mcd 200mcd 3.3V White 600mcd 350mcd 3.3V Orange 10,000mcd 500mcd 2.2V
Hyper Bright LED Prominent and Recessed Flush Forward Voltage HE Red 3,700mcd 600mcd 2.2V Green 2,000mcd 350mcd 3.2V Yellow 1,200mcd 140mcd 2.0V
Orange
4,500mcd
400mcd 2.2V
Luminous intensity will be reduced with lower operating current.
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current (Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.8VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA 28VDC 25.2 to 30.8VDC 20mA
Max Reverse Voltage: 5V
Viewing Angle: 30–100° (dependant on model)
Life Expectancy: 100,000 hours
Temperature Range: –40 to +85°C (operating & storage)
Torque: 4cNm8,00 0,315 AF
2,00 0,079
M6 x 0,50 THREAD
4
Plated brass bezel finished in bright chrome, black chrome or satin grey
www.apem.com APEM
Q SERIES Ø6mm (.236") Panel Mount LED Indicators Technical Drawings
PROMINENT BEZEL
RECESSED BEZEL
REAR EPOXY PINS
REAR EPOXY PINS
PINS
PINS
SHORT BODY WIRES
SHORT BODY WIRES
SHORT BODY PINS
SHORT BODY PINS
REAR EPOXY WIRES
REAR EPOXY WIRES
WIRES
WIRES
SOLDER LUG
SOLDER LUG
5
3,50 0,138
7,
00[0
,275
]
2,0x0,5[0,078x0,02]M6x0,5
23,10 0,909
6,00 0,2368,75 0,344
17,10 0,673
3,50 0,138
7,
00 [0
,275
]
M6x0,5
1,25
0,04
91,
250,
049
9,50 0,37411,00 0,4338,75 0,344
0,50
0,02
0
17,10 0,673
3,50 0,138
7,
00[0
,275
]
M6x0,5
200,0+/-10[7,874+/-0,393]
8,75 0,344
7,
00[0
,275
]
3,50 0,1388,75 0,344
10,00 0,39416,60 0,65418,98 0,747
0,50
0,02
01,
250,
049
1,25
0,04
9
7,
00[0
,275
]
3,50 0,1388,75 0,344
10,00 0,394
M6 x0,5
200,00+/-10[7,874+/-0,393]
12,00 0,472
3,50 0,138
7,
00[0
,275
]
9,50 0,37411,00 0,433
1,25
0,04
91,
250,
049
M6x0,5
8,75 0,344
0,50
0,02
0
12,00 0,472
M6x0,5
3,50 0,138
7,
00[0
,275
]
200,0+/-10[7,874+/-0,393]
8,75 0,344
2,25 0,089
7,
00[0
,275
]
6,00 0,236
2,0x0,5[0,078x0,02]M6x0,5
8,75 0,34424,75 0,974 18,75 0,738
2,25 0,089
7,
00[0
,275
]
M6x0,5
9,50 0,37411,00 0,433
1,25
0,04
91,
250,
049
8,75 0,344
0,50
0,02
0
18,75 0,738
2,25 0,089
7,
00[0
,275
]
M6x0,5
200,0+/-10[7,874+/-0,393]8,75 0,344
7,
00[0
,275
]
2,25 0,0898,75 0,344
11,65 0,45916,60 0,65418,10 0,713
0,50
0,02
01,
250,
049
1,25
0,04
9
M6 x0,5
7,
00[0
,275
]
2,25 0,0898,75 0,344
11,65 0,459
M6 x0,5
200,0+/-10[7,874+/-0,393]
13,65 0,537
2,25 0,089
7,
00[0
,275
]
M6x0,5
8,75 0,344 14,60 0,57516,98 0,668
0,50
0,02
01,
250,
049
1,25
0,04
9
7,
00[0
,275
]
2,25 0,089
13,65 0,537
M6x0,5
200,0+/-10[7,874+/-0,393]
8,75 0,345
www.apem.com
FLUSH BEZEL
Q SERIES Ø6mm (.236") Panel Mount LED Indicators Technical Drawings
REAR EPOXY PINS
PINS
SHORT BODY WIRESSHORT BODY PINSREAR EPOXY WIRES
WIRES
SOLDER LUG
6APEM
27,00 1,0631,00 0,039
7,
00[0
,275
]
6,00 0,236
M6x0,52,0x0,5 [0.078x0.02]
8,75 0,344
7,
00 [0
,275
]
21,00 0,827
1,00 0,039
M6x0,5
9,50 0,374
11,00 0,433
1,25
0,04
91,
250,
049
0,50
0,02
0
8,75 0,344
1,00 0,039
7,
00 [0
,275
]M6x0,5
200,0 +/-10[7,874+/-0,393]
8,75 0,34421,00 0,827
7,
00[0
,275
]
1,00 0,0398,75 0,344
13,90 0,547
16,60 0,65418,10 0,713
2,50
0,09
81,
250,
049
M6 x0,5
0,50
0,02
0
7,
00[0
,275
]
1,00 0,0398,75 0,344
13,90 0,547
M6 x0,5
200,0+/-10[7,874+/-0,393]
15,90 0,626
1,00 ,039
7,
00 [0
,275
]
1,25
0,04
91,
250,
049
M6x0,5
0,50
0,02
0
9,50 0,37411,00 0,433
8,75 0,344
7,
00[0
,275
]
15,90 0,626
1,00 0,039 200,0 +/-10[7,874 +/- 0,393]
M6x0,5
8,75 0,344
7 www.apem.com
STANDARD OPTIONS
Q 6 P 1 B XX G 12 E
• Gold solder lug terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 24AWG UL 1061, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternative voltages consult APEM
• Bi-color LEDs, by connecting the gold solder lug (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC
• Take care when soldering to the terminals (recommended solder temperature 270°C - 2 sec)
• Short body options are only available up to 24VDC
• Maximum panel thickness 7mm
Q
Example Q6F3CXXB12EØ6mm, flush bezel, wire terminals bright chrome finish, fixed light, blue, 12VDC LED, IP67 panel sealed
1 = Solder Lug
2 = Pins
3 = Wires
4 = Rear epoxy Pins
5 = Rear epoxy Wires
6 = Short body Pins
7 = Short body Wires
C = Bright Chrome
B = Black Chrome
G = Satin Grey
R = Red
G = Green
Y = Yellow
B = Blue
W = White
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
SO = Super Bright Orange
RG = Red/Green
RY = Red/Yellow
GY = Green/Yellow
02 = no resistor*06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
(Blank) = Unsealed
E = IP67
XX = Fixed Light
KK = Flashing Light (12V – 28VDC)
YY = Bi-color
SERIES MOUNTING HOLE
6 = Ø6mm P = Prominent
R = Recessed
F = Flush
BEZEL STYLE TERMINALS BEZEL FINISH TYPE OF
ILLUMINATION LED COLOR VOLTAGE SEALING
The Q6 Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
Q SERIES Ø6mm (.236") Panel Mount LED Indicators Overview
APEM
* = For resistorless versions (02) please refer to the forward voltage
www.apem.com
Q8 SERIES Ø8mm (.315") Panel Mount LED Indicators
8APEM
Distinctive featuresPanel mount LED indicators with 5mm colored diffused epoxy lensor 5mm water clear super bright LEDs. Bright chrome, black chrome or satin grey bezel finish.Prominent, recessed and flush bezel styles. Voltage: 2VDC - 220VAC. Terminals: 2.8 x 0.8 solder lug/fastons, pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical ApplicationsMedicalTelecommunications EngineeringTransport SystemsSpecial VehiclesAgricultural Vehicles
9www.apem.com
Features
• 8mm panel mounting LED indicator• 5mm colored diffused epoxy lens or 5mm water clear super bright LEDs• • Prominent, recessed and flush bezel styles• 2VDC – 220VAC• (2.8 x 0.8) solder lug/faston terminals, pins or (200mm long) wire terminations
(2.0 x 0.5) solder lug/faston terminals on tricolor versions•
IP67 sealing option (EN60529)•
Supplied with fixing nut and spring washer
NB: UL Recognized Component
Q SERIES Ø8mm (.315") Panel Mount LED Indicators Distinctive features and specification
PANEL CUTOUT
Ø 8.00 +0.15/-0.0
Standard LED Intensity Prominent and Recessed Flush Forward Voltage HE Red 100mcd 12mcd 2.0V Green 60mcd 8mcd 2.2V Yellow 50mcd 6mcd 2.1V Blue 1600mcd 200mcd 3.3V White 1600mcd 500mcd 3.3V Orange 45mcd 110mcd 2.2V Bi-color (Typical) (Red/Green) 30/12mcd 15/10mcd 2.0V/2.2V Tri-color (Typical) (Red/Green/Yellow) 60/15/13mcd 15/10/6mcd 2.0V/2.2V/2.1V
Bi-color - The color is changed by reversing the polarity of the supply voltage.Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Super Bright LED Prominent and Recessed Flush Forward Voltage HE Red 10,000mcd 1300mcd 2.2V Green 10,000mcd 120mcd 3.3V Yellow 3,300mcd 350mcd 2.0V Blue 2,200mcd 280mcd 3.3V White 2,500mcd 350mcd 3.3V Orange 4,000mcd 500mcd 2.2V
Hyper Bright LED Prominent and Recessed Flush Forward Voltage HE Red 6,000mcd 980mcd 2.2V Green 1,900mcd 300mcd 3.3V Yellow 2,100mcd 250mcd 2.0V
Orange
4,500mcd
110mcd 2.2V
Luminous intensity will be reduced with lower operating current.
Max Reverse Voltage: 5V Viewing Angle: 30–100° (dependant on model) Life Expectancy: 100,000 hours Temperature Range: –40 to +85°C
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current(Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.3VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA
28VDC 25.2 to 30.8VDC 20mA 110VAC 99 to 121VAC 6mA 220VAC 207 to 253VAC 3mA
APEM
Torque: 20 to 25cNm(operating & storage)
10,00 0,394 AF2,00 0,079
M8 x 0,75 THREAD
Plated brass bezel finished in bright chrome, black chrome or satin grey
10 www.apem.com
Q SERIES Ø8mm (.315") Panel Mount LED Indicators Technical Drawings
PROMINENT BEZEL
RECESSED BEZEL
REAR EPOXY PINS
REAR EPOXY PINS
PINS
PINS
SHORT BODY WIRES
SHORT BODY WIRES
SHORT BODY PINS
SHORT BODY PINS
REAR EPOXY WIRES
REAR EPOXY WIRES
WIRES
WIRES
SOLDER LUG/FASTONS
SOLDER LUG/FASTONS
SHORT BODY SOLDER LUG/FASTONS
SHORT BODY SOLDER LUG/FASTONS
EXTENDED SHORT BODY SOLDER LUG/FASTONS
EXTENDED SHORT BODY SOLDER LUG/FASTONS
APEM
M8x0,75
28,75 1,132
5,10 0,201
9,50
0,37
4
9,35 0,36810,00 0,394
2,8x0,8[0,11x0,031]
8,75 0,344
1,25
0,04
9
22,50 0,886
5,10 0,2016,50 0,256
8,00 0,315
1,25
0,04
9
9,50
0,37
4
M8x0,75
8,75 0,344
0,50
0,02
0
M8x0,75
22,50 0,886
5,10 0,201
9,50
0,37
4
200,0+/-10[7,874+/-0,393]8,75 0,344
0,50
0,02
01,
250,
049
1,25
0,04
9
19,38 0,76320,88 0,8225,10 0,201
8,75 0,34410,50 0,413
9,50
0,37
4
M8x0,75 9,50
0,37
4
5,10 0,2018,75 0,345
10,50 0,413
M8x0,75
200,0 +/-10[7,874 +/-0,393]
1,25
0,04
9
12,50 0,492
5,10 0,201
9,50
0,37
4
16,50 0,65018,00 0,709
1,25
0,04
9
8,75 0,344
0,50
0,02
0
M8x0,75
12,50 0,492
5,10 0,201
9,50
0,37
4
M8x0,75
200,0 +/-10[7.874+/-0,393]8,75 0,344
2,8x0,8[0,11X0,393]
31,75 1,250
3,00 0,118
9,40
,370
9,35 0,36810,00 0,394
8,75 0,344
M8x0,75
25,50 1,004
3,00 0,118
9,40
0,37
0
6,50 0,2568,00 ,315
1,25
0,04
91,
250,
049
M8x0,75
8,75 0,344
0,50
0,02
0
25,50 1,004
3,00 0,118
9,50
0,37
4
M8x0,75
200,00+/-10[7,874+/-0,393]8,75 0,344
9,50
0,37
4
3,00 0,1188,75 0,344
13,50 0,531
20,00 0,78718,50 0,728
0,50
0,02
01,
250,
049
1,25
0,04
9
M8x0,75
9,50
0,37
4
3,00 0,1188,75 0,344
13,50 0,531
M8x0,75
200,0+/-10[7,874+/-0,393]
15,50 0,610
3,00 0,118
9,50
0,37
4
16,50 0,65018,00 0,709
1,25
0,04
91,
250,
049
M8x0,75
8,75 0,344
0,50
0,02
0
3,00 0,118
15,50 0,610
9,50
0,37
4
200,00 +/-10[7,874+/-0,393]
M8x0,75
8,75 0,3443,00 0,118
15,50 0,6109,35 0,36810,00 0,394
9,50
0,37
4
M8x0,752,8x0,8[0,11x0,031]
8,75 0,344
12,50 0,4929,35 0,00910,00 0,3945,10 0,201
9,50
0,37
4
2,8x0,8 [0,11x0,031]M8x0,75
8,75 0,344
2,8x0,5[0.11x0.019]M8x0,759,
50,3
74
5,10 0,2018,75 0,344
15,50 0,6109,35 0,36810,00 0,394
2,8x0,5[0.11x0.019]M8x0,759,
500,
374
3,00 0,1188,75 0,344
18,50 0,7289,35 0,36810,00 0,394
11www.apem.com
FLUSH BEZEL
Q SERIES Ø8mm (.315") Panel Mount LED Indicators Technical Drawings
REAR EPOXY PINS
PINS
SHORT BODY WIRES
SHORT BODY PINSREAR EPOXY WIRES
WIRESSOLDER LUG/FASTONS
SHORT BODY SOLDER LUG/FASTONS
APEM
1,00 0,039
33,85 1,3339,35 0,36810,00 0,394
9,50
0,37
4
2,8x0,8[0,11x0,031]M8x0,75
8,75 0,34427,60 1,087
1,00 0,0396,50 0,2568,00 0,315
1,25
0,04
91,
250,
049
9,50
0,37
4
M8x0,75
8,75 0,344
0,50
0,02
0
9,50
0,37
4
1,00 0,0398,75 0,344
27,60 1,087
M8x0,75
200,0 +/-10[7.874+/-0,393]
9,50
0,37
4
1,00 0,0398,75 0,344
15,60 0,61418,50 0,72820,00 0,787
0,50
0,02
01,
250,
049
1,25
0,04
9
M8x0,759,
500,
374
1,00 0,0398,75 0,344
15,60 0,614
M8x0,75
200,0+/-10[7,874+/-0,393]
17,60 0,693
1,00 0,03916,50 0,65018,00 0,709
9,50
0,37
4
1,25
0,04
91,
250,
049
M8x0,75
8,75 0,344
0,50
0,02
0
17,60 0,693
1,00 0,039
9,50
0,37
4
M8x0,75
200,0+/-10[7,874+/-0,393]
8,75 0,3441,00 0,039
17,60 0,693
10,00 0,3949,35 0,368
9,50
0,37
4
M8x0,752,8x0,8[0,11x0,031]
8,75 0,344
EXTENDED SHORT BODY SOLDER LUG/FASTONS
M8X0,752,8x0,5[0.11x0.019]
9,50
0,37
4
1,00 0,0399,75 0,384
21,60 0,8509,35 0,36810,00 0,394
12 www.apem.com
STANDARD OPTIONS
Q 8 P 8 G XX Y 12 E
Q 1 = Solder Lug/ Fastons(2.8 x 0.8)
2 = Pins
3 = Wires
4 = Rear epoxy Pins
5 = Rear epoxy Wires
6 = Short body Pins
7 = Short body Wires
C = Bright Chrome
B = Black Chrome
G = Satin Grey
R = Red
G = Green
Y = Yellow
B = Blue
W = White
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
SO = Super Bright Orange
RG = Red/Green
RY = Red/Yellow
GY = Green/Yellow
02 = no resistor*06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
110 = 110VAC
220 = 220VAC
(Blank) = Unsealed
E = IP67
XX = Fixed Light
KK = Flashing Light (12V – 28VDC)
YY = Bi-color
SERIES MOUNTING HOLE
8 = Ø8mm P = Prominent
R = Recessed
F = Flush
BEZEL STYLE TERMINALS BEZEL FINISH TYPE OF
ILLUMINATION LED COLOR VOLTAGE SEALING
The Q8 Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
Q SERIES Ø8mm (.315") Panel Mount LED Indicators Overview
Example Q8P3CXXY02EØ8mm, prominent bezel, 200mm wire termination bright chrome finish, fixed light, yellow2VDC LED, IP67 panel sealed
• Gold Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 24AWG UL1061, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternative voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC. [AC products not available]
• Take care when soldering to the Faston terminals (recommended solder temperature 270°C - 2 sec)
• Terminal options 6,7 & 9 are only available up to 28V (DC Only) tri-color not available with terminal 9
• Terminal code 8 is only available without integral resistor
•
•
Maximum panel thickness 7mm
We recommend using Hyperbright orSuperbright LEDs for use at 110VAC and 220VAC
8 = Short bodyLug/ Fastons(2.8 x 0.8)
ZZ = Tri-color
RYG = Red/Yellow/Green
9 = Extendedshort body solder Lug/ Fastons(2.8 x 0.5)
APEM
* = For resistorless versions (02) please refer to the forward voltage
• The Tri-color LED has red and green LEDs when both are connected yellow is produced
• Standard Tri-color Faston terminals are two Anodes (+) and one Cathode (-)
Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
•
www.apem.com
Q12 SERIES Ø12mm (.472") Panel Mount LED Indicators
13APEM
Distinctive features
Panel mount LED indicators with 8mm colored diffused epoxy lensor 8mm water clear super bright LEDs.Bright chrome, black chrome or satin grey bezel finish.Prominent bezel style. Voltage: 2VDC - 220VAC.Terminals: 2.8 x 0.8 solder lug/faston, pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical Applications
Process Controls Professional Electrical Appliances Communications, Radar Civil engineering vehicles, trucks, diggers, crane Trains HVAC, Energy Management Lifts Machine Tools
14www.apem.com
Q SERIES Ø12mm (.472") Panel Mount LED Indicators Distinctive features and specification
Features
• 12mm panel mounting LED indicator• 8mm colored diffused epoxy lens or 8mm water clear super bright LEDs• • Prominent bezel style• 2VDC – 220VAC• (2.8 x 0.8) solder lug/faston terminals, pins or (200mm long) wire terminations• IP67 sealing option (EN60529)• Supplied with fixing nut and spring washer
NB: UL Recognized Component
Ø 12.00 +0.15/-0.0
PANEL CUTOUT
Standard LED Intensity Prominent Forward Voltage HE Red 350mcd 2.0V Green 60mcd 2.2V Yellow 50mcd 2.1V Blue 800mcd 3.3V White 1100mcd 3.3V Orange 100mcd 2.0V Bi-color (Typical) (Red/Green) 20/10mcd 2.0V/2.2V Tri-color (Typical) (Red/Green/Yellow) 80/15/13mcd 2.0V/2.2V/2.1V
Bi-color - The color is changed by reversing the polarity of the supply voltage.Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Super Bright LED Prominent Forward Voltage HE Red 3,000mcd 2.2V Green 8,000mcd 3.3V Yellow 1,400mcd 2.3V Blue 1,500mcd 3.3V White 1,200mcd 3.3V Orange 2,000mcd 2.2V
Hyper Bright LED Prominent Forward Voltage HE Red 1,200mcd 2.0V Green 2,200mcd 3.3V Yellow 1,600mcd 2.0V
Orange
4,300mcd
2.2V
Luminous intensity will be reduced with lower operating current.
Max Reverse Voltage: 5V Viewing Angle: 30–100° (dependant on model) Life Expectancy: 100,000 hours Temperature Range: –40 to +85°C
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current(Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.3VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA
28VDC 25.2 to 30.8VDC 20mA 110VAC 99 to 121VAC 6mA 220VAC 207 to 253VAC 3mA
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
APEM
Torque: 75cNm
Plated brass bezel finished in bright chrome, black chrome or satin grey
(operating & storage)
15,00 0,591 AF 2,00 0,079
M12 x 0,75 THREAD
15 www.apem.com APEM
Q SERIES Ø12mm (.472") Panel Mount LED Indicators Technical Drawings
PROMINENT BEZEL
REAR EPOXY PINS
PINS
SHORT BODY WIRESSHORT BODY PINSREAR EPOXY WIRES
WIRES
SOLDER LUG/FASTONS
13,5
00,
531
4,50 0,1778,75 0,344
27,50 1,0834,50 0,1776,00 0,236
0,50
0,02
02,
00 [0
,078
]2,
00 [0
,078
]
M12x0,75
13,5
00,
531
4,50 0,1778,75 0,344
27,50 1,083
M12x0,75
200,0+/-10[7,874+/-0,393]
13,5
00,
531
4,50 0,1778,75 0,34413,50 0,531
18,50 0,72820,00 0,787
0,50
0,02
01,
250,
049
1,25
0,04
9
M12x0,75
13,5
00,
531
4,50 0,1778,75 0,344
27,50 1,0834,50 0,1776,00 0,236
0,50
0,02
02,
00 [0
,078
]2,
00 [0
,078
]
M12x0,75
13,5
00,
531
4,50 0,1778,75 0,344
200,0+/-10[7,874+/-0,393]
M12x0,75
13,50 0,531
4,50 0,177
16,00 0,63016,00 0,63017,50 0,689
0,50
0,02
01,
250,
001
1,25
0,04
9
M12x0,7513,5
00,
531
8,75 0,34413
,50
0,53
1
4,50 0,177
16,00 [0,629]
200,0+/-10[7,874+/-0,393]
M12x0,75
8,75 0,344
www.apem.com16 APEM
Q SERIES Ø12mm (.472") Panel Mount LED Indicators Overview
STANDARD OPTIONS
Q 12 P 1 B XX G 12 E
• Gold Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 24AWG UL1061, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternative voltage consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC
• Take care when soldering to the Faston terminals (recommended solder temperature 270°C - 2 sec)
• Max voltage for pins and wires is 28V
• Maximum panel thickness 7mm
• Tri-colors are only available behind panel epoxy sealed with wires (option 1) or pins (option 3)
• 110VAC and 220VAC only available with solder lug/Faston terminals
• We recommend using Hyperbright or Superbright LEDs for use at 110VAC and 220VAC
Q
Example Q12P7GXXG12EØ12mm, prominent bezel, short body wires, satin chrome finish, fixed light, green, 12VDC LED, IP67 panel sealed
1 = Solder Lug/ Fastons(2.8 x 0.8)
2 = Pins
3 = Wires
4 = Rear epoxy Pins
5 = Rear epoxy Wires
6 = Short body Pins
7 = Short body Wires
C = Bright Chrome
B = Black Chrome
G = Satin Grey
R = Red
G = Green
Y = Yellow
B = Blue
W = White
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
SO = Super Bright Orange
RG = Red/Green
RY = Red/Yellow
GY = Green/Yellow
RYG = Red/Yellow/Green
02 = no resistor*06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
110 = 110VAC
220 = 220VAC
(Blank) = Unsealed
E = IP67
XX = Fixed Light
KK = Flashing Light(12 - 28VDC)
YY = Bi-color
ZZ = Tri-color
SERIES MOUNTING HOLE
12 = Ø12mm P = Prominent
BEZEL STYLE TERMINALS BEZEL FINISH TYPE OF
ILLUMINATION LED COLOR VOLTAGE SEALING
The Q12 Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
* = For resistorless versions (02) please refer to the forward voltage
• The Tri-color LED has red and green LEDs when both are connected yellow is produced
• Standard Tri-color Faston terminals are two Anodes (+) and one Cathode (-)
Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
•
www.apem.com
Q14 SERIES Ø14mm (.551") Panel Mount LED Indicators
17APEM
Distinctive featuresPanel mount LED indicators with 10mm colored diffused epoxy lensor 10mm water clear super bright LEDs.Custom engraving availableBright chrome, black chrome or satin grey bezel finish.Prominent and flush bezel styles. voltage: 2VDC - 220VAC.Terminals: 2.8 x 0.8 solder lug/fastons, pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical ApplicationsProcess Controls Professional Electrical Appliances Communications, Radar Civil engineering vehicles, trucks, diggers, crane Trains HVAC, Energy Management Lifts Machine Tools
18www.apem.com
Q SERIES Ø14mm (.551") Panel Mount LED Indicators Distinctive features and specification
Features
• 14mm panel mounting LED indicator• 10mm colored diffused epoxy lens or 10mm water clear super bright LEDs• • Prominent and flush bezel styles•
2VDC – 220VAC• (2.8 x 0.8) solder lug/Faston terminals, pins or (200mm long) wire terminations• IP67 sealing option (EN60529)• Supplied with fixing nut and spring washer
NB: UL Recognized Component
PANEL CUTOUT
Ø 14.00 +0.15/-0.0
Standard LED Intensity Prominent Flush Forward Voltage HE Red 100mcd 10mcd 2.0V Green 60mcd 5mcd 2.2V Yellow 50mcd 4mcd 2.1V Blue 540mcd 100mcd 3.3V White 1000mcd 120mcd 3.3V Orange 100mcd 200mcd 2.0V Bi-color (Typical) (Red/Green) 15/15mcd 14/10mcd 2.0V/2.2V Tri-color (Typical) (Red/Green/Yellow) 80/50/50mcd 180/30/30mcd 2.0V/2.2V/2.1V
Bi-color - The color is changed by reversing the polarity of the supply voltage.Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Super Bright LED Prominent Flush Forward Voltage HE Red 17,000mcd 2000mcd 2.2V Green 4,100mcd 680mcd 3.5V Yellow 2,500mcd 350mcd 2.3V Blue 2,500mcd 300mcd 3.3V White 4,400mcd 200mcd 3.3V Orange 2800mcd 300mcd 2.1V
Hyper Bright LED Prominent Flush Forward Voltage HE Red 2,800mcd 800mcd 2.1V Green 2,200mcd 250mcd 3.2V Yellow 1,300mcd 250mcd 2.0V
Orange
850mcd
200mcd 2.1V
Luminous intensity will be reduced with lower operating current.
Max Reverse Voltage: 5V Viewing Angle: 30–100° (dependant on model) Life Expectancy: 100,000 hours Temperature Range: –40 to +85°C
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current(Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.3VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA
28VDC 25.2 to 30.8VDC 20mA 110VAC 99 to 121VAC 6mA 220VAC 207 to 253VAC 3mA
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
Torque: 75cNm
Plated brass bezel finished in bright chrome, black chrome or satin grey
(operating & storage)
Custom engraving available
•
17,00 0,669 AF 3,00 0,118
M14 x 1,0 THREAD
APEM
VOYC1511US
19 www.apem.com
Q SERIES Ø14mm (.551") Panel Mount LED Indicators Technical Drawings
PROMINENT BEZEL
FLUSH BEZEL
REAR EPOXY PINS
REAR EPOXY PINS
PINS
PINS
SHORT BODY WIRES
SHORT BODY WIRES
SHORT BODY PINS
SHORT BODY PINS
REAR EPOXY WIRES
REAR EPOXY WIRES
WIRES
WIRES
SOLDER LUG/FASTONS
SOLDER LUG/FASTONS
APEM
34,10 1,343
1,50 0,0599,35 0,36810,00 0,394
M14x1,0 2,8x0,8[0,11x0,031]
13,5[0,531]
16,0
00,
630
16,0
00,
630
1,50 0,0595,50 0,2177,00 0,276
1,25
0,04
91,
250,
049
M14x1,00,
500,
020
13,50[0,531]29,10 1,146
M14x1,0
29,10 1,146
16,0
00,
630
1,50 0,05913,50[0,531]
200,0+/-10[7,874+/-0,393]
16,0
00,
630
1,50 0,05913,50[0,531]
17,85 0,703
18,25 0,71916,75 0,659
0,50
0,02
01,
250,
049
1,25
0,04
9
M14x1,0
16,0
00,
630
1,50 0,05913,50[0,531]
17,85 0,703
M14x1,0
200,0+/-10[7,874+/-0,393]
20,10 0,79114,50 0,57116,00 ,6301,50 0,059
16,0
00,
630
1,25
0,04
91,
250,
049
13,50[0,531]
0,50
0,02
0
20,10 0,791
1,50 0,059
M14x1,0
13,50[0,531]
16,0
00,
630
200,0+/-10[7,874+/-0,393]
2,8x0,8[0,11x0,031]M14x1,0
33,75 1,3299,35 0,36810,00 0,3944,75 0,187
13,50 0,531
16,0
00,
630
28,75 1,132
4,75 0,18713,50 0,531
M14x1,016,0
00,
630
200,0+/-10[7,874+/-0,393]
M14x1,0
16,0
00,
630
4,75 0,18713,50 0,531
28,75 1,132
1,25
0,04
91,
250,
049
5,50 0,2177,00 0,276
0,50
0,02
0
16,0
00,
630
4,75 0,18713,50 0,53117,50 0,689
18,25 0,71916,75 0,659
0,50
0,02
01,
250,
049
1,25
0,04
9
M14x1,0
16,0
00,
630
4,75 0,18713,50 0,53217,50 0,689
M14x1,0
200,0+/-10[7,874+/-0,393]
19,75 0,778
4,75 0,18714,50 0,57116,00 0,630
1,25
0,04
91,
250,
049
M14x1,0
13,50 0,531
16,0
00,
630
0,50
0,02
0 M14x1,0
19,75 0,778
4,75 0,18713,50 0,531
16,0
00,
630
200,0+/-10[7,874+/-0,393]
20www.apem.com
Q SERIES Ø14mm (.551") Panel Mount LED Indicators Custom options
CUSTOM ENGRAVING
Code Symbol DescriptionCode Symbol Description Code Symbol Description
-0AJ High Beam
-097 Low Beam
-027 Rear Fog
-026 Front Fog
-021 WindscreenWiper
-022 WindscreenWasher
-023 VentilatorFan
-0AH TurnSignal
-098 Side Lights
-041 Horn
-013 HazardWarning
-018 Heating
-0BU Brake Test
-0K6 Arrow
-0AG Battery
-0GP Oil Can
-020 WindscreenHeating
-086 ABS
-0EL EngineCoil
-0SB Seat Belt
-0UB USBConnection
-0ST Steam
-0EU ECU
-0AD Side Step
-012 Air Con
-040 Engine
-0BR Boot/TrunkRelease
Suffix the part number with legend code (see example on page 4)
APEM
Cable length & connector
For custom cable length andconnectors please contactAPEM
Some common codes are listed above, for your custom requirements please contact APEM.Unless specified standard engraving with white infill will be supplied.
21 www.apem.com
Q SERIES Ø14mm (.551") Panel Mount LED Indicators Order Overview
STANDARD OPTIONS
Q 14 P 1 C XX B 28 E
• Gold Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 22AWG UL1007, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternative voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC
• Take care when soldering to the Faston terminals (recommended solder temperature 270°C - 2 sec)
• Short body pins and wires are only available up to 28VDC
• The Tri-color LED has red and green LEDs when both are connected yellow is produced
• Standard Tri-color Faston terminals are two Anodes (+) and one Cathode (-)
• Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
• Maximum panel thickness 11mm
• We recommend using Hyperbright or Superbright LEDs for use at 110VAC and 220VAC
•
For multi-voltage options please consult APEM
Q
Example Q14F3CXXR12E-0SBØ14mm, Flush bezel, wire termination, red LEDbright chrome finish, fixed light, 12VDC LED, IP67 panel sealed,engraved with seat belt symbol (see page 3)
1 = Solder Lug/ Fastons(2.8 x 0.8)
2 = Pins
3 = Wires
4 = Rear epoxy Pins
5 = Rear epoxy Wires
6 = Short body Pins
7 = Short body Wires
C = Bright Chrome
B = Black Chrome
G = Satin Grey
R = Red
G = Green
Y = Yellow
B = Blue
W = White
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
RG = Red/Green
RY = Red/Yellow
GY = Green/Yellow
RYG = Red/Yellow/Green
02 = no resistor*06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
110 = 110VAC
220 = 220VAC
(Blank) = Unsealed
E = IP67
XX = Fixed Light
KK = Flashing Light(12- 28VDC)
YY = Bi-color
ZZ = Tri-color
SERIES MOUNTING HOLE
14 = Ø14mm P = Prominent
F = Flush
BEZEL STYLE TERMINALS BEZEL FINISH TYPE OF
ILLUMINATION LED COLOR VOLTAGE SEALING
The Q14 Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
* = For resistorless versions (02) please refer to the forward voltage
www.apem.com
Q16 SERIES Ø16mm (.630") Panel Mount LED Indicators
22APEM
Distinctive featuresPanel mount LED indicators with 10mm colored diffused epoxy lensor 10mm water clear super bright LEDs.Custom engraving and secret until lit polycarbonate decals availableBright chrome, black chrome or satin grey bezel finish.Prominent and flush bezel styles. voltage: 2VDC - 220VAC.Terminals: 2.8 x 0.8 solder lug/fastons, pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical ApplicationsProcess Controls Professional Electrical Appliances Communications, Radar Civil engineering vehicles, trucks, diggers, crane Trains HVAC, Energy Management Lifts Machine Tools
23www.apem.com
Q SERIES Ø16mm (.630") Panel Mount LED Indicators Distinctive features and specification
Features
• 16mm panel mounting LED indicator• 10mm colored diffused epoxy lens or 10mm water clear super bright LEDs• • • Prominent and flush bezel styles• 2VDC – 220VAC• (2.8 x 0.8) solder lug/faston terminals, pins or (200mm long) wire terminations• IP67 sealing option (EN60529)• Supplied with fixing nut and spring washer
NB: UL Recognized Component
Ø 16.00 +0.15/-0.0
PANEL CUTOUT
Standard LED Intensity Prominent Flush Forward Voltage HE Red 100mcd 10mcd 2.0V Green 60mcd 5mcd 2.2V Yellow 50mcd 4mcd 2.1V Blue 540mcd 100mcd 3.3V White 1000mcd 120mcd 3.3V Orange 100mcd 200mcd 2.0V Bi-color (Typical) (Red/Green) 15/15mcd 14/10mcd 2.0V/2.2V Tri-color (Typical) (Red/Green/Yellow) 80/50/50mcd 180/30/30mcd 2.0V/2.2V/2.1V
Bi-color - The color is changed by reversing the polarity of the supply voltage.Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Super Bright LED Prominent Flush Forward Voltage HE Red 17,000mcd 2000mcd 2.2V Green 4,100mcd 680mcd 3.5V Yellow 2,500mcd 350mcd 2.3V Blue 2,500mcd 300mcd 3.3V White 4,400mcd 200mcd 3.3V Orange 2,800mcd 300mcd 2.1V
Hyper Bright LED Prominent Flush Forward Voltage HE Red 2,800mcd 800mcd 2.1V Green 2,200mcd 250mcd 3.2V Yellow 1,300mcd 250mcd 2.0V
Orange
850mcd
200mcd 2.1V
Luminous intensity will be reduced with lower operating current.
Max Reverse Voltage: 5V Viewing Angle: 30–100° (dependant on model) Life Expectancy: 100,000 hours Temperature Range: –40 to +85°C
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current(Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.3VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA
28VDC 25.2 to 30.8VDC 20mA 110VAC 99 to 121VAC 6mA 220VAC 207 to 253VAC 3mA
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
Torque: 75cNm(operating & storage)
19,00 0,748 AF 2,40 0,094
M16 x 1,0 THREAD
APEM
Plated brass bezel finished in bright chrome, black chrome or satin grey Secret until lit polycarbonate decals or custom engraving
24 www.apem.com
Q SERIES Ø16mm (.630") Panel Mount LED Indicators Technical Drawings
PROMINENT BEZEL
FLUSH BEZEL
REAR EPOXY PINS
REAR EPOXY PINS
PINS
PINS
SHORT BODY WIRES
SHORT BODY WIRES
SHORT BODY PINS
SHORT BODY PINS
REAR EPOXY WIRES
REAR EPOXY WIRES
WIRES
WIRES
SOLDER LUG/FASTONS
SOLDER LUG/FASTONS
APEM
2,00 0,079
33,60 1,3239,35 0,36810,00 0,394
18,3
00,
720
M16x1,0 2,8x0,8[0,11x0,031]
13,50[0,531]
18,3
00,
720
28,60 1,126
2,00 0,079
1,25
0,04
91,
250,
049
5,50 0,2177,00 0,276
M16x1,00,
500,
020
13,50[0,531]
M16x1,0
2,00 0,079
18,3
00,
720
28,60 1,12613,50[0531]
200,0+/-10[7,874+/-0,393]
18,3
00,
720
2,00 0,07913,50[0,531]
17,35 0,68316,75 0,65918,25 0,719
0,50
0,02
01,
250,
049
1,25
0,04
9
M16x1,0
18,3
00,
720
2,00 0,07913,50[0,531]
17,35 0,683
200,0+/-10[7,874+/-0,393]
M16x1,0
18,3
00,
720
14,50 1,45016,00 0,630
1,25
0,04
91,
250,
049M16x1,0
2,00 0,07913,50[0,531]
19,60 0,772
0,50
0,02
0
2,00 0,079
19,60 0,772
18,3
00,
720
M16x1,0
13,50[0,531]200,0+/-10[7,874+/-0,393]
M16x1,0
4,75 0,187
33,75 1,3299,35 0,36810,00 0,394
18,3
00,
720
2,8x0,8[0,11x0,031]
13,50 0,531
M16x1,0
4,75 0,18713,50 0,531
28,75 1,132
1,25
0,04
91,
250,
049
5,50 ,2177,00 0,276
18,3
00,
720
0,50
0,02
0
18,3
00,
720
4,75 0,18713,50 0,53117,50 0,689
16,75 0,65918,25 0,719
0,50
0,02
01,
250,
049
1,25
0,04
9
M16x1,0M16x1,0
4,75 0,187
18,3
00,
720
13,50 0,531200,0+/-10[7,874+/-0,393]
28,75 1,132
18,3
00,
720
4,75 0,18713,50 0,53117,50 0,689
M16x1,0
200,0+/-10[7,874+/-0,393]
4,75 0,187
19,75 0,77814,50 0,57116,00 0,630
18,3
00,
720
M16x1,0
1,25
0,04
91,
250,
049
13,50 0,531
0,50
0,02
0
18,3
00,
720
19,75 19,750
M16x1,0
13,50 0,5314,75 0,187 200,0+/-10
[7,874+/-0,393]
25www.apem.com
Q SERIES Ø16mm (.630") Panel Mount LED Indicators Custom options
Secret Until Lit Polycarbonate Inserts
Off
On
Code Symbol Description Code Symbol Description
-327 Rear fog
-397 Low beam
-3AH Turn Signal
-313 Hazard
-3BU Brake test
-3K6 Arrow
-3AG Battery
-3GP Oil can
-3AJ High beam
-3PB Park Brake
-398 Side Lights
Suffix the part number with legend code (see example on page 5)
APEM
-3SB Seat Belt
-3TP TyrePressure
CheckEngine-3CE
-3EC EngineTemperature
-3FP Fuel
-3BF Brake Failure
Some common codes are listed above, for your custom requirements please contact APEM.
26 www.apem.com
Q SERIES Ø16mm (.630") Panel Mount LED Indicators
APEM
Custom options
Code Symbol DescriptionCode Symbol Description Code Symbol Description
-0AJ High Beam
-097 Low Beam
-027 Rear Fog
-026 Front Fog
-021 WindscreenWiper
-022 WindscreenWasher
-023 VentilatorFan
-0AH TurnSignal
-098 Side Lights
-041 Horn
-013 HazardWarning
-018 Heating
-0BU Brake Test
-0K6 Arrow
-0AG Battery
-0GP Oil Can
-020 WindscreenHeating
-086 ABS
-0EL EngineCoil
-0SB Seat Belt
-0UB USBConnection
-0ST Steam
-0EU ECU
-0AD Side Step
-012 Air Con
-040 Engine
-0BR Boot/TrunkRelease
Suffix the part number with legend code (see example on page 5)
For custom cable length andconnectors please contactAPEM
Some common codes are listed above, for your custom requirements please contact APEM.Unless specified standard engraving with white infill will be supplied.
Custom Engraving Cable length & connector
27www.apem.com
Q SERIES Ø16mm (.630") Panel Mount LED Indicators Overview
STANDARD OPTIONS
Q 16 F 1 G XX Y 24 E
• Gold Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 22AWG UL1007, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternative voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC
• Take care when soldering to the Faston terminals (recommended solder temperature 270°C - 2 sec)
• Short body pins and wires are only available up to 28VDC
• The Tri-color LED has red and green LEDs when both are connected yellow is produced
• Standard Tri-color Faston terminals are two Anodes (+) and one Cathode (-)
• Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
• Maximum panel thickness 11mm
• We recommend using Hyperbright or Superbright LEDs for use at 110VAC and 220VAC
•
For multi-voltage options please consult APEM
Q
Example Q16F7BXXHR12E-3PBØ16mm, flush metal bezel, wire terminalsMatt black chrome finish, fixed light, Red, 12VDC LED, IP67 panel sealedSecret until lit Park Brake Symbol (see page 3)
1 = Solder Lug/ Fastons(2.8 x 0.8)
2 = Pins
3 = Wires
4 = Rear epoxy Pins
5 = Rear epoxy Wires
6 = Short body Pins
7 = Short body Wires
Metal
C = Bright Chrome
B = Black Chrome
G = Satin Grey
Plastic
CP = Bright
BP = Black
GP = Satin Grey
AU = Gold
R = Red
G = Green
Y = Yellow
B = Blue
W = White
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
RG = Red/Green
RY = Red/Yellow
GY = Green/Yellow
RYG = Red/Yellow/Green
02 = no resistor*06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
110 = 110VAC
220 = 220VAC
(Blank) = Unsealed
E = IP67
XX = Fixed Light
KK = Flashing Light(12 - 28VDC)
YY = Bi-color
ZZ = Tri-color
SERIES MOUNTING HOLE
16 = Ø16mm Metal
P = Prominent
F = Flush
Plastic
PP = Prominent
FP = Flush
BEZEL STYLE TERMINALS BEZEL FINISH TYPE OF
ILLUMINATION LED COLOR VOLTAGE SEALING
The Q16 Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
APEM
* = For resistorless versions (02) please refer to the forward voltage
www.apem.com
Q19 SERIES Ø19mm (.748") Panel Mount LED Indicators
28APEM
Distinctive featuresPanel mount LED indicators with 10mm colored diffused epoxy lensor 10mm water clear super bright LEDs.Bright chrome, black chrome or satin grey bezel finish.Prominent and flush bezel styles. voltage: 2VDC - 220VAC.Terminals: 2.8 x 0.8 solder lug/fastons, pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical ApplicationsProcess Controls Professional Electrical Appliances Communications, Radar Civil engineering vehicles, trucks, diggers, crane Trains HVAC, Energy Management Lifts Machine Tools
29
Q SERIES Ø19mm (.748") Panel Mount LED Indicators Distinctive features and specification
Features
• 19mm panel mounting LED indicator• 10mm colored diffused epoxy lens or 10mm water clear super bright LEDs• • Prominent and flush bezel styles•
2VDC – 220VAC• (2.8 x 0.8) solder lug/faston terminals, pins or (200mm long) wire terminations• IP67 sealing option (EN60529)• Supplied with fixing nut and spring washer
NB: UL Recognized Component
Standard LED Intensity Prominent Forward Voltage HE Red 100mcd 2.0V Green 60mcd 2.2V Yellow 50mcd 2.1V Blue 540mcd 3.3V White 1000mcd 3.3V Orange 100mcd 2.0V Bi-color (Typical) (Red/Green) 15/15mcd 2.0V/2.2V Tri-color (Typical) (Red/Green/Yellow) 80/50/50mcd 2.0V/2.2V/2.1V
Bi-color - The color is changed by reversing the polarity of the supply voltage.Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Super Bright LED Prominent Forward Voltage HE Red 17,000mcd 2.2V Green 4,100mcd 3.5V Yellow 2,500mcd 2.3V Blue 2,500mcd 3.3V White 4,400mcd 3.3V Orange 2,800mcd 2.1V
Hyper Bright LED Prominent Forward Voltage HE Red 2,800mcd 2.1V Green 2,200mcd 3.2V Yellow 1,300mcd 2.0V
Orange
850mcd
2.1V
Luminous intensity will be reduced with lower operating current.
Max Reverse Voltage: 5V Viewing Angle: 30–100° (dependant on model) Life Expectancy: 100,000 hours Temperature Range: –40 to +85°C
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current(Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.3VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA
28VDC 25.2 to 30.8VDC 20mA 110VAC 99 to 121VAC 6mA 220VAC 207 to 253VAC 3mA
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
Torque: 75cNm
Plated brass bezel finished in bright chrome, black chrome or satin grey
Custom engraving available
Flush10mcd
5mcd4mcd
100mcd120mcd200mcd
14/10mcd180/30/30mcd
Flush2000mcd
680mcd350mcd300mcd300mcd300mcd
Flush800mcd250mcd250mcd200mcd
•
Ø 19.00 +0.15/-0.0
PANEL CUTOUT
22,00 0,866 AF 3,00 0,118
M19 x 1,0 THREAD
www.apem.comAPEM
VOYC1511US
(operating & storage)
30 www.apem.com
Q SERIES Ø19mm (.748") Panel Mount LED Indicators Technical Drawings
PROMINENT BEZEL
REAR EPOXY PINS
PINS
SHORT BODY WIRESSHORT BODY PINSREAR EPOXY WIRES
WIRES
SOLDER LUG/FASTONS
FLUSH BEZEL
REAR EPOXY PINS
PINS
SHORT BODY WIRESSHORT BODY PINSREAR EPOXY WIRES
WIRES
SOLDER LUG/FASTONS
APEM
22,0
00,
866
M19x1,02,8x0,8[0,11x0,031]
4,75 0,187
33,75 1,3299,35 0,36810,00 0,394
13,50 0,531
22,0
00,
866
4,75 0,18713,50 0,531
28,75 1,132
1,25
0,00
11,
250,
049
5,50 0,2177,00 0,276
0,50
,020
4,75 0,187
28,75 1,132
22,0
0,8
66
13,50 0,531200,0+/-10[7,874+/-0,393]
M19x1,0
22,0
00,
866
4,75 0,18713,50 0,53117,50 0,689
16,75 0,65918,25 0,719
0,50
0,02
01,
250,
049
1,25
0,04
9
M19x1,0
22,0
00,
866
4,75 0,18713,50 0,53117,50 0,689
M19x1,0
200,0+/-10[7,874+/-0,393]
4,75 0,187
19,75 0,77814,50 0,57116,00 0,630
1,25
0,04
91,
250,
049
22,0
00,
866
13,50 0,531
M19x1,0
0,50
0,02
0
4,75 0,187
19,75 0,778
22,0
00,
866
13,50 0,531
M19x1,0
200,0+/-10[7,874+/-0,393]
22,0
00,
866
M19x1,02,8x0,8[0,11x0,031]
33,75 1,3299,35 0,36810,00 0,394
13,50 0,5311,85 0,073
22,0
00,
866
13,50 0,53128,75 1,132
1,25
0,04
9
7,00 0,2765,50 0,217
0,50
,020
1,85 0,073
1,25
0,04
9
28,75 1,132
22,0
0,8
66
13,50 0,531 200,0+/-10[7,874+/-0,393]
M19x1,0
1,85 0,073
22,0
00,
866
13,50 0,53117,50 0,689
16,75 0,65918,25 0,719
0,50
0,02
01,
250,
049
1,25
0,04
9
M19x1,0
1,85 0,073
22,0
00,
866
13,50 0,53117,50 0,689
M19x1,0
200,0+/-10[7,874+/-0,393]
1,85 0,073
19,75 0,77816,00 0,630
14,50 0,571
1,25
0,04
91,
250,
049
22,0
00,
866
13,50 0,531
M19x1,0
0,50
0,02
0
1,85 0,073
19,75 0,778
22,0
00,
866
13,50 0,531
M19x1,0
200,0+/-10[7,874+/-0,393]
1,85 0,073
31www.apem.com
Q SERIES Ø19mm (.748") Panel Mount LED Indicators Custom options
CUSTOM ENGRAVING
Code Symbol DescriptionCode Symbol Description Code Symbol Description
-0AJ High Beam
-097 Low Beam
-027 Rear Fog
-026 Front Fog
-021 WindscreenWiper
-022 WindscreenWasher
-023 VentilatorFan
-0AH TurnSignal
-098 Side Lights
-041 Horn
-013 HazardWarning
-018 Heating
-0BU Brake Test
-0K6 Arrow
-0AG Battery
-0GP Oil Can
-020 WindscreenHeating
-086 ABS
-0EL EngineCoil
-0SB Seat Belt
-0UB USBConnection
-0ST Steam
-0EU ECU
-0AD Side Step
-012 Air Con
-040 Engine
-0BR Boot/TrunkRelease
Suffix the part number with legend code
APEM
Cable length & connector
For custom cable length andconnectors please contactAPEM
Some common codes are listed above, for your custom requirements please contact APEM.Unless specified standard engraving with white infill will be supplied.
32 www.apem.com
Q SERIES Ø19mm (.748") Panel Mount LED Indicators Overview
STANDARD OPTIONS
Q 19 P 1 B XX G 12 E
• Gold Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 22AWG UL1007, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternate voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC
• Take care when soldering to the Faston terminals (recommended solder temperature 270°C - 2 sec)
• Short body pins and wires are only available up to 28VDC
• The Tri-color LED has red and green LEDs when both are connected yellow is produced
• Standard Tri-color Faston terminals are two Anodes (+) and one Cathode (-)
• Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
• Maximum panel thickness 11mm
• We recommend using Hyperbright orSuperbright LEDs for use at 110VAC and 220VAC
•
For multi-voltage options please consult APEM
Q
Example Q19P1BXXR12EØ19mm, prominent bezel, solder lug terminals, black chrome finish, fixed light, red, 12VDC LED, IP67 panel sealed
1 = Solder Lug/ Fastons(2.8 x 0.8)
2 = Pins
3 = Wires
4 = Rear epoxy Pins
5 = Rear epoxy Wires
6 = Short body Pins
7 = Short body Wires
Metal
C = Bright Chrome
B = Black Chrome
G = Satin Grey
R = Red
G = Green
Y = Yellow
B = Blue
W = White
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
RG = Red/Green
RY = Red/Yellow
GY = Green/Yellow
RYG = Red/Yellow/Green
02 = no resistor*06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
110 = 110VAC
220 = 220VAC
(Blank) = Unsealed
E = IP67
XX = Fixed Light
KK = Flashing Light(12 - 28VDC)
YY = Bi-color
ZZ = Tri-color
SERIES MOUNTING HOLE
19 = Ø19mm Metal
P = Prominent
BEZEL STYLE TERMINALS BEZEL FINISH TYPE OF
ILLUMINATION LED COLOR VOLTAGE SEALING
The Q19 Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
* = For resistorless versions (02) please refer to the forward voltage
F = Flush
APEM
www.apem.com
Q22 SERIES Ø22mm (.866") Panel Mount LED Indicators
33APEM
Distinctive featuresPanel mount LED indicators with 18mm colored diffused epoxy lens.Custom engraving available.Metal bezel finish: bright chrome, black chrome or satin grey.Plastic bezel finished in black.Prominent and flush bezel styles. Voltage: 5.5VDC - 220VAC. Terminals: 2.8 x 0.8 solder lug/fastons, pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical ApplicationsProcess Controls Professional Electrical Appliances Communications, Radar Civil engineering vehicles, trucks, diggers, crane Trains HVAC, Energy Management Lifts Machine Tool
34www.apem.com
Q SERIES Ø22mm (.866") Panel Mount LED Indicators Distinctive features and specification
Features
• 22mm panel mounting LED indicator• 18mm colored diffused epoxy lens or 18mm super bright LEDs• Plated brass bezel finished in bright chrome, black chrome or satin grey • Black ABS Plastic bezel option• Prominent and flush bezel styles• Custom engraving available• (2.8 x 0.8) solder lug/faston terminals, pins or (200mm long) wire terminations• IP67 sealing option (EN60529)• Supplied with fixing nut and spring washer
NB: UL Recognized Component
PANEL CUTOUT
Ø 22.00 +0.15/-0.0
Standard LED Intensity Prominent Flush Forward Voltage HE Red 80mcd 70mcd 5.7V Green 95mcd 33mcd 6.0V Yellow 60mcd 29mcd 5.9V Blue 120mcd 100mcd 9.9V White 350mcd 120mcd 3.3V
Bi-color (Typical) (Red/Green)
80/50mcd
80/50mcd 2.0V/2.2V
Tri-color (Typical) (Red/Green/Yellow)
80/50/50mcd
80/50/50mcd 2.0V/2.2V/2.1V
Bi-color - The color is changed by reversing the polarity of the supply voltage.Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Super bright LED (Diffused) Prominent Flush Forward Voltage
HE Red
930mcd 700mcd 5.7V
Green
1,060mcd 980mcd 9.0V
Yellow
1,780mcd 1,250mcd 6.0V
Luminous intensity will be reduced with lower operating current.
Max Reverse Voltage: 5V Viewing Angle: 30–100° (dependant on model) Life Expectancy: 100,000 hours Temperature Range: –40 to +85°C
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current(Min to Max) (Typical All Types)
05 (No Resistor) 3.3 to 9.9VDC 40mA max*
12VDC 10.8 to 13.2VDC 40mA 24VDC 21.6 to 26.4VDC 40mA
28VDC 25.2 to 30.8VDC 40mA 110VAC 99 to 121VAC 5mA 220VAC 207 to 253VAC 3mA
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
Torque: 100cNm(operating & storage)
27,00 1,063 AF 3,25 0,128
M22 x 1,0 THREAD
APEM
35 www.apem.com
Q SERIES Ø22mm (.866") Panel Mount LED Indicators Technical Drawings
PROMINENT BEZEL
FLUSH BEZEL
REAR EPOXY PINS
REAR EPOXY PINS
SHORT BODY WIRES
SHORT BODY WIRES
SHORT BODY PINS
SHORT BODY PINS
REAR EPOXY WIRES
REAR EPOXY WIRES
SOLDER LUG/FASTONS
SOLDER LUG/FASTONS
APEM
M22x1,02,8x0,8[0,11x0,031]
39,00 1,5359,35 0,36810,00 0,394
25,0
00,
984
11,75 0,4632,50 0,098
25,0
00,
984
2,50 0,098
22,00 0,86616,00 0,630
19,00 0,748
1,25
0,04
91,
250,
049M22x1,0
4,75 0,187
0,70
,028
M22x1,0
25,0
00,
984
2,50 0,09811,75 0,46322,00 0,866
200,0+/-10[7,874+/-0,393]
25,0
00,
984
2,50 0,09811,75 0,463
23,50 0,92514,50 0,571
17,50 0,689
0,70
0,02
81,
250,
049
1,25
0,04
9M22x1,0
25,0
00,
984
2,50 0,09811,75 0,463
24,00 0,945
M22x1,0
200,0+/-10[7,874+/-0,393]
6,50 0,256
35,00 1,3788,65 0,34110,00 0,394
M22x1,0
25,0
00,
984
14,25 0,561
25,0
00,
984
6,50 0,256
18,00 0,709
M22x1,0
14,25 0,561200,0+/-10[7,874+/-0,393]
6,50 0,256
18,00 0,70916,00 0,630
19,00 0,748
1,25
0,04
91,
250,
049
25,0
00,
984
M22x1,0
14,25 0,561
0,70
,028
6,50 0,25614,25 0,56119,50 0,768
14,50 0,57117,50 0,689
0,70
0,02
81,
250,
049
1,25
0,04
9
25,0
00,
984
M22x1,0
25,0
00,
984
6,50 0,25614,25 0,56120,00 0,787
200,0+/-10[7,874+/-0,393]
M22 x 1,0
36www.apem.com
Q SERIES Ø22mm (.866") Panel Mount LED Indicators Custom Options
Code Symbol DescriptionCode Symbol Description Code Symbol Description
-0AJ High Beam
-097 Low Beam
-027 Rear Fog
-026 Front Fog
-021 WindscreenWiper
-022 WindscreenWasher
-023 VentilatorFan
-0AH TurnSignal
-098 Side Lights
-041 Horn
-013 HazardWarning
-018 Heating
-0BU Brake Test
-0K6 Arrow
-0AG Battery
-0GP Oil Can
-020 WindscreenHeating
-086 ABS
-0BD EngineCoil
-0SB Seat Belt
-0UB USBConnection
-0ST Steam
-0EU ECU
-0AD Side Step
-012 Air Con
-040 Engine
-0BR Boot/TrunkRelease
Suffix the part number with legend code (see example on page 4)
Custom Engraving Cable length & connector
Some common codes are listed above, for your custom requirements please contact APEM.Unless specified standard engraving with white infill will be supplied
For custom cable length andconnectors please contactAPEM
APEM
37 www.apem.com
Q SERIES Ø22mm (.866") Panel Mount LED Indicators Overview
STANDARD OPTIONS
Q 22 F 1 BP XX W 28 E DL
• Gold Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 22AWG UL1007, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternative voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC
• Take care when soldering to the Faston terminals (recommended solder temperature 270°C - 2 sec)
• Pin and Wire options are epoxy sealed at the rear of the bezels, termination options 4 and 5
• The Tri-color LED has red and green LEDs when both are connected yellow is produced
• Standard Tri-color Faston terminals are two Anodes (+) and one Cathode (-)
• Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
• Maximum panel thickness: Prominent = 12mm, Flush = 10mm
• Plastic bezel material: ABS
• Daisy chaining option - has negative (Cathode) terminals linked (3 x Fastons), solder lugs only
• Lamp test facility option 4 x solder lug/Faston only
• We recommend using super bright LEDs for use at 110 and 220VAC
Q
Example Q22F5CXXG12E-0AGØ22mm, flush bezel, rear epoxy wire terminals, bright chrome finish, fixed light, green, 12VDC LED, IP67 panel sealed, Battery symbol marking
Metal
C = Bright Chrome
B = Black Chrome
G = Satin Grey
Plastic
BP = Black
R = Red
G = Green
Y = Yellow
B = Blue
W = White
SR = Super bright Red
SG = Super bright Green
SY = Super bright Yellow
RG = Red/GreenRY = Red/Yellow
GY = Green/Yellow
RYG = Red/Yellow/Green
05 = no resistor* 12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
110 = 110VAC
220 = 220VAC
(Blank) = Unsealed
E = IP67
DL = Daisy Chain
LT = Lamp Test
XX = Fixed Light
KK = Flashing Light (only 12VDC)
YY = Bi-color
ZZ = Tri-color
SERIES MOUNTING HOLE
22 = Ø22mm Metal
P = Prominent
F = Flush
Plastic
PP = Prominent
FP = Flush
BEZEL STYLE TERMINALS BEZEL FINISH TYPE OF
ILLUMINATION LED COLOR VOLTAGE SEALING OPTIONS
The Q22 Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
1 = Solder Lug/ Fastons(2.8 x 0.8)
4 = Rear epoxy Pins
5 = Rear epoxy Wires
6 = Short body Pins
7 = Short body Wires
* = For resistorless versions (05) please refer to the forward voltage
Anodised Flush
AR = Red
AG = Green
AY = Yellow
AB = Blue
APEM
www.apem.com
QRM-SERIES Rear Panel Mounting LED IndicatorTechnical Drawings
8mm
10mm
12mm
www.apem.com
QRM6 SERIES Ø6mm (.236") Rear Panel Mount LED Indicators
38APEM
Distinctive featuresRear panel mount LED indicators with 3mm colored diffused epoxy lensor 3mm water clear super bright LEDs. Black chrome finish. Voltage: 2VDC - 28VDC.Terminals: Pins or 200mm long wires.IP67 sealing option (EN60529).Supplied with fixing nut and spring washer.
Typical ApplicationsProcess Controls Professional Electrical Appliances Communications, Radar Civil engineering vehicles, trucks, diggers, crane Trains HVAC, Energy Management Lifts Machine Tools
39www.apem.com
QRM6 SERIES Rear Panel Mount LED Indicators Distinctive features and specifications
Features• Ø6mm rear mounting LED indicator• 3mm flush diffused LED, standard, hyper bright or water clear• Bi-color LED options• • 2VDC – 28VAC.DC• 200mm wires or pin terminations• IP67 sealed (EN60529)•
Supplied with fixing nut, spring washer and O-ring
NB: UL Recognized Component
Black chrome finish
Standard LED Intensity MCD Output Forward Voltage(all voltages)
HE Red
10mcd 2.0V
Green
8mcd 2.2VYellow
2.1V
Blue
100mcd 3.8V
White
220mcd 3.8V
Bi-color (Typical) (Red/Green)
10/8mcd 2.0V/2.2V The color is changed by reversing the polarity of the supply voltage.
Hyper Bright MCD Output Forward Voltage(all voltages)
Luminous intensity will be reduced with lower operating current.Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current (Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.8VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA 28VDC 25.2 to 30.8VDC 20mA
Max Reverse Voltage: 5V Viewing Angle: 60° Life Expectancy: 100,000 hours Operating Temperature Range: –40 to +85°C Storage Temperature Range: –55 to +100°C
Max panel thickness: 3.5mmTorque: 60cNm
6mcd
MaterialsBody: Black chrome plated brassNut: Black chrome plated brassPanel seal: Nitrile O-ring
Lock washer: Spring steelTerminal seal: EpoxyWires: 24AWG to UL1061
Epoxy sealed rear end•
Super BrightHE RedGreenYellowBlueWhiteOrange
MCD Output (all voltages)500mcd350mcd140mcd200mcd350mcd500mcd
2.2V3.5V2.3V3.3V3.3V2.2V
Forward Voltage
HE RedGreenYellow
600mcd350mcd140mcd
2.2V3.2V2.0V
8,00 0,315 AF2,00 0,079
M6 x 0,50 THREAD
APEM
Ø6 +0.15/-0.0
2.80
PANEL CUTOUT
Rear
Pins Wires
QRM6 SERIES Rear Panel Mount LED IndicatorsTechnical Drawings
40 www.apem.com APEM
8,00 0,315
7,00
0,27
68,
250,
325
16,7
70,
660
M6x0,5 THREAD
0,50 0,020 x0,50[0,020] SQ2,50 0,0981,25 0,049
5,50 0,217
M6x0,5 THREAD
8,00 0,3155,50 0,217
7,00
0,27
68,
250,
325
16,7
50,
659
BLACK 24AWG UL1061WIRE..LED CATHODE -
RED 24AWG UL1061WIRE..LED ANODE +
200,
0 +/
-10
[7.8
74 +
/-0.3
93]
41 www.apem.com
QRM6 SERIES Rear Panel Mount LED Indicators Overview
STANDARD OPTIONS
QRM
• Standard wire length is 200mm, 24AWG UL1061, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternate voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one colour is produced, by reversing the supply voltage another colour is produced – Bi-colours are available up to 28VDC
• Take care when soldering (recommended solder temperature 270°C - 2 sec)
•
•
Maximum panel thickness 3.5mm
For multi-voltage options please consult APEM
QRM
Example QRM64BXXR24EØ6mm mounting hole with pin terminations, black chromefinish, fixed light, Red 24VDC, panel sealed to IP67
SERIES
R = Red
G = Green
Y = Yellow
B = Blue
W = White
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
RG = Red/Green
LED COLOR
02 = no resistor*06 = 6VDC
12 = 12VDC
24 = 24VDC
28 = 28VDC
VOLTAGE
The QRM Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
MOUNTING HOLE
TYPE OF ILLUMINATION
XX = Fixed light
YY = Bi-color
TERMINALS
5 = Wires
4 = Pins
BEZEL FINISH
B = Black Chrome
RY = Red/Yellow
GY = Green/Yellow
SEALING
E = IP67 (Standard6 = Ø6mm
6 4 B XX HB 24A E
APEM
* = For resistorless versions (02) please refer to the forward voltage
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
SO = Super Bright Orange
www.apem.com
QRM-SERIES Rear Panel Mounting LED IndicatorTechnical Drawings
8mm
10mm
12mm
www.apem.com
QRM8 SERIES Ø8mm (.315") Rear Panel Mount LED Indicators
42APEM
Distinctive featuresRear panel mount LED indicators with 5mm colored diffused epoxy lensor 5mm water clear super bright LEDs. Black chrome finish.Voltage: 2VDC - 28VAC/DC Pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical ApplicationsMedicalTelecommunications EngineeringTransport SystemsSpecial VehiclesAgricultural Vehicles
43www.apem.com
QRM8 SERIES Rear Panel Mount LED Indicators Distinctive features and specifications
Features• Ø8mm rear mounting LED indicator• 5mm flush diffused LED, standard, hyper bright or water clear• Bi-color and Tri-color LED options• • 2VDC – 28VAC/DC• 200mm wires or pin terminations• IP67 sealed (EN60529)•
Supplied with fixing nut, spring washer and O-ring(Dress nut available as an option - contact APEM)
NB: UL Recognized Component
Black chrome finish
Standard LED Intensity MCD Output Forward Voltage(all voltages)
MCD Output Forward Voltage(all voltages)
HE Red
12mcd 2.0V
Green
8mcd 2.2VYellow
2.1V
Blue
200mcd 3.8V
White
500mcd 3.8V
Bi-color (Typical) (Red/Green)
15/10mcd 2.0V/2.2V
Bi-color - the color is changed by reversing the polarity Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Hyper Bright MCD Output Forward Voltage(all voltages)
Luminous intensity will be reduced with lower operating current.Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice. * Customer to supply resistor for desired operating current.
Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated. Luminous intensities and color shades of white LEDs may vary within a batch.
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current (Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.8VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA 28VDC 25.2 to 30.8VDC 20mA
Max Reverse Voltage: 5V Viewing Angle: 60° Life Expectancy: 100,000 hours Operating Temperature Range: –40 to +85°C Storage Temperature Range: –55 to +100°C
Max panel thickness: 3.5mmTorque: 60cNm
Tri-color (Typical) (Red/Green/Yellow) 15/10/6mcd 2.0V/2.2V/2.1V
6mcd
MaterialsBody: Black chrome plated brassNut: Black chrome plated brassPanel seal: Nitrile O-ring
Lock washer: Spring steelTerminal seal: EpoxyWires: 24AWG to UL1061
.
Epoxy sealed rear end•
Super Bright LEDHE RedGreenYellowBlueWhiteOrange
1300mcd120mcd350mcd280mcd350mcd500mcd
2.2V3.3V2.0V3.3V3.3V2.2V
HE RedGreenYellow
980mcd300mcd250mcd
2.2V3.3V2.0V
10,00 0,394 AF2,00 0,079
M8 x 0,75 THREAD
PANEL CUTOUT
APEM
Ø8 +0.15/-0.0
3.50
Rear
Pins Wires
QRM8 SERIES Rear Panel Mount LED IndicatorsTechnical Drawings
9,30
0,36
615
,30
0,60
2 6,75 0,266
11,00 0,433
M8x0,75 THREAD
1,25 0,0491,25 0,049
0,50 x 0,50 SQ[0.019x0.019]
ADODE +CATHODE -
6,50
0,25
611,00 0,433
6,75 0,266
9,30
0,36
66,
500,
256
15,3
00,
602
200,
0 +/
-10
[7.8
74 +
/-0.3
93]
BLACK 24AWG UL1061WIRE..CATHODE -
RED 24AWG UL1061WIRE..ANODE +
M8x0,75 THREAD
10,00 0,394 3,00 0,118
1,00
0,03
9
1,00 0,039
10,2
00,
401
4,50 0,1772,25 0,089
Dress nuts
44 www.apem.com APEM
Pt.No. AUK0001
Pt.No. AUK0002
45www.apem.com
QRM8 SERIES Rear Panel Mount LED Indicators Custom options
11,00 0,433
6,75 0,266
24,4
0,9
619,
300,
366
6,50
0,25
6
2,50 0,0982,50 0,098
1,00 0,040
SILVER PIN CATHODE -
GOLD PIN RED LED ANODE +GOLD PIN GREEN LED ANODE +
6,75 0,266
11,00 0,433
9,30
0,36
6
6,50
0,25
6
15,3
00,
602
2,50 0,0982,50 0,098
1,00 0,040
GOLD PIN ANODE +SILVER PIN CATHODE -
M8x0,75 THREAD
6,75 0,266
11,00 0,4336,
500,
256
9,30
0,36
624
,40
0,96
1
1,00 0,040
2,50 0,0982,50 0,098
M8x0,75 THREAD
SILVER PIN..CATHODE - GOLD PIN..ANODE +
-X0245
Fixed and Bi-color long body rigid pins Tri-color long body and rigid PCB
-X0246
Long body matches the behind panel depth of APEM 12200X778 PCB mounting military gradde toggle switches
-X0259
Fixed and Bi-color standard body rigid pins
APEM
To apply the above custom option, suffix the part number with the -X reference numberExample QRM84BXXHB24AE-X0245
46 www.apem.com
QRM8 SERIES Rear Panel Mount LED Indicators Overview
STANDARD OPTIONS
QRM
• Standard wire length is 200mm, 24AWG UL1061, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternate voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one colour is produced, by reversing the supply voltage another colour is produced – Bi-colours are available up to 28VDC
• Take care when soldering (recommended solder temperature 270°C - 2 sec)
•
•
The Tri-color LED has red and green LEDs when both are connected yellow is produced
•
Standard Tri-color termination is two Anodes (+) and one Cathode (-)
•
Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
•
Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
•
Maximum panel thickness 3.5mm
For multi-voltage options please consult APEM
QRM
Example QRM84BXXHR24AEØ8mm mounting hole with pin terminations, black chromefinish, fixed light, Red 24VAC, panel sealed to IP67
SERIES
R = Red
G = Green
Y = Yellow
B = Blue
W = White
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
RYG = Red/Yellow/Green
RG = Red/Green
LED COLOR
02 = no resistor*06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
VOLTAGE
The QRM Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
MOUNTING HOLE
TYPE OF ILLUMINATION
XX = Fixed light
YY = Bi-color
ZZ = Tri-color
TERMINALS
5 = Wires
4 = Pins
BEZEL FINISH
B = Black Chrome
RY = Red/YellowGY = Green/Yellow
SEALING
E = IP67 (Standard
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
SO = Super Bright Orange
8 = Ø8mm
8 4 B XX HB 24A E
APEM
* = For resistorless versions (02) please refer to the forward voltage
www.apem.com
QRM-SERIES Rear Panel Mounting LED IndicatorTechnical Drawings
8mm
10mm
12mm
www.apem.com
QRM-NV SERIES Ø8mm (.315") Rear Panel Mount NVIS LED Indicators
47APEM
Distinctive featuresRear panel mount LED indicators with 5mm colored diffused epoxy lenswith NVIS compatible fliters forNVIS Green ANVIS Green BNVIS Yellow ANVIS Yellow BNVIS RedNVIS White Black chrome finish.Voltage: 2VDC - 28VAC/DC Pins or 200mm long wires.IP67 sealing option (EN60529). Supplied with fixing nut and spring washer.
Typical ApplicationsMilitaryMedicalTelecommunications EngineeringTransport SystemsSpecial VehiclesAgricultural Vehicles
48www.apem.com
QRM-NV SERIES NVIS Compatible Rear Panel Mounting LED Indicator
Distinctive features and specifications
Features
• Ø8mm rear mounting LED indicator• NVIS Green A, NVIS Green B, NVIS Yellow, NVIS Red, NVIS White• High temperature NVG filters• • Black chrome finish• 2VDC - 28VDC• 200mm wire or rigid pin (1.00mm) terminations• IP67 sealed (EN60529)
NVIS compliant to MIL Std 3009
Luminous intensity will be reduced with lower operating current.
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.• Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current (Min to Max) (Typical All Types)
02 (No Resistor) 2.1 to 3.3VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA 28VDC 25.2 to 30.8VDC 20mA
Max Reverse Voltage: 5V Viewing Angle: 60° Life Expectancy: 100,000 hours Operating Temperature Range: –40 to +85°C Storage Temperature Range: –55 to +100°C
Max panel thickness: 3.5mmTorque: 60cNm
MaterialsBody: Black chrome plated brassNut: Black chrome plated brassPanel seal: Nitrile O-ring
Lock washer: Spring steelTerminal seal: EpoxyWires: 24AWG to UL1213
Rear end epoxy sealedSupplied with fixing nut, spring washer and O-ring(Optional dress nuts available)
••
LEDColor
NVISRadiance
NVISChromoticity
DominantWavelength
MCDOutput
ForwardVoltage
NW1S Green A NRA ≤ 1.7eE-10 @ 0.1fL r ≤ .037 530nm 150mcd 3.3V
NW1S Yellow Class A 5.0E-8 ≤ NRA ≤ 1.5E-7 @ 15fL r ≤ .083 - 150mcd 3.3V
NW1S Yellow Class B 4.7E-8 ≤ NRB ≤ 1.47E-7 @ 15fL r ≤ 0.83 585nm 150mcd 3.3V
NW1S Red 4.7E-8 ≤ NRB ≤ 1.4E-7 @15 fL r ≤ .060 605nm 110mcd 2.1V
NW1S White NRA ≤ 1.0E-9 @ 0.1fL r ≤ .40 (x).33 (y).33 150mcd 3.3V
NW1S Green A NRA ≤ 1.7eE-10 @ 0.1fL r ≤ .057 555nm 150mcd 3.3V
APEM
Rear
Pins Wires
QRM-NV SERIES
Technical Drawings NVIS Compatible Rear Panel Mounting LED Indicator
49
10,00 0,394 AF2,00 0,079
M8 x 0,75 THREAD
8mm nut (std)
Ø 6,00 ±0,1
8mm
Hardware Panel Cut out Dress nuts for 8mm QRM
10,00 0,394 3,00 0,118
1,00
0,03
91,00 0,039
10,2
00,
401
4,50 0,1772,25 0,089
9,30
,366
6,50
0,25
6
17,0
00,
669
6,75 0,266
11,00 0,433
2,50 0,0982,50 0,098
1,00 0,040
SILVER PIN..CATHODE - GOLD PIN..ANODE +
M8x0,75 THREAD
200,
0 +/
-10
[7.8
74 +
/-0.3
93]
6,50
,256
9,30
0,36
617
,00
0,66
9
6,75 0,266
11,00 0,433
M8x0,75 THREAD
BLACK 24AWG UL1213WIRE..CATHODE -
LED COLOUR 24AWGUL1213 WIRE..ANODE +
www.apem.com APEM
Pt.No. AUK0001
Pt.No. AUK0002
50 www.apem.com
QRM-NV SERIES
Overview
STANDARD OPTIONS
QRM-NV
• Standard wire length is 200mm, 24AWG UL1213, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternate voltages consult APEM
•
•
Take care when soldering (recommended solder temperature 270°C - 2 sec)
•
•
Maximum panel thickness 3.5mm•
For resistorless versions (02) please pay attention to the forward voltage
For multi-voltage options please consult Apem
QRM-NV
Example QRM-NV85BXXNV-GRA24AE
Ø8mm mounting hole with wire terminations,black chrome finish, fixed lightNVIS Green A 24V AC,panel sealed to IP67
SERIES
NV-GRA = NVIS Green A
NV-GRB = NVIS Green B
NV-YWA = NVIS Yellow A
NV-YWB = NVIS Yellow B
NV-RD = NVIS Red
LED COLOR
02 = no resistor* 06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
VOLTAGE
The QRM Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
MOUNTING HOLE
TYPE OF ILLUMINATION
XX = Fixed light
TERMINALS
5 = Wires
4 = Ridgid Pins
BEZEL FINISH
B = Black Chrome
SEALING
E = IP67 (Standard)
NVIS Compatible Rear Panel Mounting LED Indicator
NV-WH = NVIS White
Suitable for the toughest enviroment and compliant to MIL standard specification
8 = Ø8mm
8 5 B XX NV-GRA 24A E
APEM
* = For resistorless versions (02) please refer to the forward voltage
www.apem.com
QS SERIES Snap in Panel Mount LED Indicators
51APEM
Distinctive featuresSnap in panel mount LED indicators with colored diffused flat lens,for typical replacement of filament and neon indicators.
• 6mm, 8mm, 10mm and 12mmØ cut-out sizes • Front panel snap-in mounting requires no additional hardware • Colored diffused flat lenses • Available colours: Red, Green, Yellow, Blue, Orange, White (clear) • Voltage range: 2VDC – 220VAC • Terminations: solder lug/faston, 6mm (2.0 x 0.5mm), 8mm, 10mm, 12mm (2.8 x 0.8mm) or wires (200mm standard length) • Standard intensity diffused LEDs or high brightness LEDs for daylight viewing • Bi-color LED option • UL496 recognised component
Typical ApplicationsDomestic and Commercial white goodsCatering EquipmentFire Alarm panelsPower distribution socketsBattery chargers / Power supplies
52www.apem.com
QS SERIES Snap-in Panel Mount LED Indicators Distinctive features and specifications
Features
• 6mm, 8mm, 10mm and 12mm Ø cut-out sizes• Front panel snap-in mounting requires no additional hardware• Colored diffused flat lenses• • 2VDC – 220VAC• 6mm solder lug (2.0x0.5mm) or 200mm wire terminations•
Standard intensity diffused LED or high brightness LED for daylight viewing• Bi-color and Tri-Color (8 and 10mm only) options
NB: UL Recognized Component
Red, Green, Yellow, Blue, Orange, White (clear)
Standard LED 6mm Intensity
6mm Intensity
Forward Voltage(all voltages)
(all voltages)
HE Red Green Yellow Blue White(clear) Orange Bi-color (Typical) (Red/Green)
Bi-color - The color is changed by reversing the polarity of the supply voltage.
High Brightness Forward Voltage
HE Red
Green
Yellow
Orange
Luminous intensity will be reduced with lower operating current.
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy. The company reserves the right to change specifications without notice.* Customer to supply resistor for desired operating current.Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.Luminous intensities and color shades of white LEDs may vary within a batch.
TECHNICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current (Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 2.5VDC 20mA max* 6VDC 5.4 to 6.6VDC 20mA 12VDC 10.8 to 13.2VDC 20mA 24VDC 21.6 to 26.4VDC 20mA
28VDC 25.2 to 30.8VDC 20mA
Max Reverse Voltage: 5V Viewing Angle: 30–100° (dependant on model) Life Expectancy: 100,000 hours Operating Temperature Range: –40 to +85°C
2.5V
110VAC (not available on QS6)
220VAC (not available on QS6)
99 to 110VAC207 to 253VAC
6mA3mA
8mm, 10mm, 12mm solder lug/Faston (2.8x0.8mm) or 200mm wire terminations
•
8,10 & 12mm Intensity
8,10 & 12mm Intensity
40mcd40mcd30mcd
1,200mcd1,200mcd
60mcd20/15mcd
2.0V2.2V2.1V3.8V3.8V2.0V
2.0V/2.2V
3,700mcd2,000mcd1,200mcd4,500mcd
Tri-color (Typical) (Red/Green/Yellow)
Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
APEM
_
2.2V3.2V2.0V2.2V
100mcd60mcd50mcd
1600mcd1600mcd
45mcd30/12mcd
60/15/13mcd
6,000mcd1,900mcd2,100mcd4,500mcd
53 www.apem.com
QS SERIES Snap-in Panel Mount LED Indicators Technical Drawings
APEM
Ø6mm
Ø8mm
Ø10mm
Ø12mm
Solder lug
Solder lug/Faston
Wires
Wires
Solder lug/Faston
Solder lug/Faston
Wires
Wires
2,0x0,5 FASTON TAB7,20
0,28
3
1,34 0,05319,00 0,748
25,00 0,984
5,90
0,23
2
GOLD TAB ANODE +
SILVER TAB CATHODE -
7,20
0,28
3
1,34 0,05319,00 0,748
5,90
0,23
2
200,0 +/-10[7.874 +/- 0.393]
BLACK WIRE CATHODE -RED WIRE ANODE +
10,0
00,
394
1,50 0,059 26,50 1,04336,50 1,437
9,35 0,368
7,90
0,31
1
SILVER TAB CATHODE -
GOLD TAB ANODE +2,8x0,8 FASTON TAB
RED WIRE ANODE +BLACK WIRE CATHODE -
10,0
00,
394
1,50 0,059 26,50 1,043200,0 +/-10[7.874 +/-0.393]
7,90
0,31
1
12,0
00,
472
1,75 0,069 26,50 1,04336,50 1,437
9,35 0,368
9,85
0,38
8
2,8x0,8 FASTON TABGOLD TAB ANODE +
SILVER TAB CATHODE -
12,0
00,
472
1,75 0,069 26,50 1,043200,0 +/-10[7.874 +/-0.393]
9,85
0,38
8
BLACK WIRE CATHODE -RED WIRE ANODE +
11,8
50,
467
9,35 0,368
36,50 1,437
26,50 1,0432,00 0,079
14,0
00,
551
SILVER TAB CATHODE -
GOLD TAB ANODE +2,8x0,8 FASTON TAB
RED WIRE ANODE +BLACK WIRE CATHODE -
14,0
00,
551
2,00 0,079 26,50 1,043200,0 +/-10[7.874 +/-0.393]
11,8
50,
467
54 www.apem.com
QS SERIES Snap-in Panel Mount LED Indicators Order Overview
STANDARD OPTIONS
QS 8
• Gold solder lug/Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, QS6 & QS8 24AWG UL1061, QS10 & QS12 22AWG UL1061,red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM
• For LEDs with alternate voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced – Bi-colors are available up to 28VDC
• Take care when soldering to the Faston terminals (recommended solder temperature 270°C - 2 sec)
•
•
The Tri-color LED has red and green LEDs when both are connected yellow is produced
•
•
Maximum panel thickness 11mm
We recommend using high brightness LEDs for use at 220VAC
For multi-voltage options please consult APEM
QS
Example QS83XXR220Ø8mm mounting hole with wire terminationsfixed light, Red 220VAC
SERIES TERMINALS
R = Red
G = Green
Y = Yellow
B = Blue
W = White (clear)
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
RYG = Red/Yellow/Green (10mm Only)
RG = Red/Green
LED COLOR
02 = no resistor*06 = 6VDC
12 = 12VDC
24 = 24VDC
28 = 28VDC
110 = 110VAC
220 = 220VAC
VOLTAGE
The QS Series is available with a range of standard options, to specify your LED, simply choose one option from each column. An example is shown below.
TYPE OF ILLUMINATION
MOUNTING HOLE
1 = Solder lug/faston
3 = Wires
XX = Fixed light
YY = Bi-color
ZZ = Tri-color (10mm only)
KK = Flashing light(12 - 28VDC)
XX3 R 220
6 = Ø6mm
8 = Ø8mm
10 = Ø10mm
12 = Ø12mm
APEM
* = For resistorless versions (02) please refer to the forward voltage
www.apem.com
Q SERIES Notations
55APEM
APEM
USA63 Neck Road HAVERHILL, MA 01835 Tel: (+1) 978 372 1602 Fax: (+1) 978 372 3534 [email protected]
USA970 Park Center DriveVISTA, CA 92081 Tel: (+1) 760 598 2518 Fax: (+1) 760 598 [email protected]
BENELUXAvenue Excelsiorlaan 211930 ZAVENTEMBelgiumTel B: (+32) 27 25 05 00Tel NL: (+31) (70) 799 91 51Fax: (+32) 27 25 22 [email protected]
FRANCE55, avenue Edouard HerriotBP182303 CAUSSADE CedexTel: (+33) 5 63 93 14 98Fax: (+33) 5 63 93 19 [email protected]
GERMANYGewerbehof GiesingPaulsdorfferstr. 34, 2. OGD-81549 MUNICHTel: (+49) 89 45 99 11 0Fax: (+49) 89 48 10 [email protected]
ITALYVia Marconi 147G12030 MARENE (CN)Tel: (+39) 0172 74 31 70Fax: (+39) 0172 74 31 [email protected]
SWEDENIsafjordsgatan 35S-16440 KISTATel: (+46) 8 626 38 00Fax: (+46) 8 626 82 [email protected]
UNITED KINGDOMDrakes DriveLONG CRENDON, Bucks HP18 9BAEnglandTel: (+44) 1 844 202400Fax: (+44) 1 844 [email protected]
DENMARKMECIndustriparken 232750 BALLERUPTel: (+45) 44 97 33 66Fax: (+45) 44 68 15 [email protected]
CHINARongGuang Building, 602A11, Changshun Road200051 SHANGHAITel: (+86) 21 6278 8546, (+86) 21 6278 6872Fax: (+86) 21 6208 [email protected]
EMEA
AMERICAS
ASIAPAC
MORE THAN 130 DISTRIBUTORS WORLDWIDE(Complete list available on www.apem.com)
WORLDWIDE SALES & CUSTOMER SUPPORT
APEM SWEDEN
APEM BENELUX APEM GERMANY
MEC DENMARK
APEM CHINA
APEM ITALY
APEM FRANCE
APEM UK
APEM USAAPEM USA
APEM RESERVES TH
E RIGH
T TO AM
END
SPECIFICATIO
NS W
ITHO
UT N
OTIC
E - DESIG
N C
OU
LEUR-C
ITRON
.CO
M - PH
OTO
S: ISTOCK PH
OTO
www.apem.com
VOYG
1512
R1U
S-20
16