PANEL ANTENNAS - Amphenol Africa · PANEL ANTENNAS WITH ONE LOW BAND ARRAY 4 | April 2015. SlimLine...
Transcript of PANEL ANTENNAS - Amphenol Africa · PANEL ANTENNAS WITH ONE LOW BAND ARRAY 4 | April 2015. SlimLine...
PANEL ANTENNASWITH ONE LOW BAND ARRAY
4 | April 2015
SlimLine
SlimLineSeries
April 2015 | 5
Low visual impact multiband antennas. Engineered for very low windload while integrating 2G, 3G and 4G technologies in a compact package.
698-960 / 1695-2690 / 1695-2690 MHz
58803005880300A 5880300G 5880300DG
Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt
• Tri band antenna, dual polarisation, 6 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
SlimLineLTE Ready
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5880300
Remote Electrical Tilt AISG1.1 5880300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5880300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5880300DG
Access Ports Description (Connectors)
The antenna has 6 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Ultra Wide Band Bottom System 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck
Ultra Wide Band Top System 1695-2690 MHz Ports (2x) 7/16-DIN Female Ultra Long Neck
Electrical Characteristics R1 Y1 (Bottom) Y2 (Top)
Frequency Bands (MHz) 700 800 900 1800 2100 2600 1800 2100 2600
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
15.515.515.2
16.516.416.2
17.417.317.0
17.117.117.1
17.517.517.4
18.018.017.8
17.117.117.1
17.517.517.4
18.018.017.8
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.5 < 1.5
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61° 65° 63° 61°
Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 7.0° 6.4° 5.2° 6.5° 5.9° 4.7°
Electrical Downtilt Range 0-10° 0-12° 0-12°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
R1
Y1
Y2
6 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2688 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 27 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 761 N Lateral: 348 N Rear: 747 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
698-960 / 1695-2690 / 1695-2690 MHz
58803005880300A 5880300G 5880300DG
Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt
Packaging
Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 32 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna
Dimensions (in mm)
Installation
RED 698-960 MHz
YELLOW 1695-2690 MHz
April 2015 | 7
790-960 / 1710-2170 / 1710-2170 MHz
58802005880200A 5880200G
Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
• Tri band antenna, dual polarisation, 6 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
SlimLineSeries
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5880200
Remote Electrical Tilt AISG1.1 5880200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5880200G
Access Ports Description (Connectors)
The antenna has 6 colour-coded connectors located at the bottom face. See image on the following page.
RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck
WHITE Rings High Band (Top Array) 1710-2170 MHz Ports (Wide Band)Pattern Optimised for DCS1800 (2x) 7/16-DIN Female Ultra Long Neck
BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports (Wide Band)Pattern Optimised for UMTS2100 (2x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED) High Band (WHITE) High Band (BLUE)
Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170 1710...1880 1900...2170
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
16.5...16.716.3...16.516.0...16.3
16.7...17.216.5...17.016.3...16.5
16.5...16.916.4...16.716.3...16.5
16.9...17.316.7...17.216.5...17.0
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.5 < 1.5
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 72°...68°...65° 65° 62° 65° 62°
Vertical Beamwidth (-3 dB) 7° 7° 7° 7° 7°
Electrical Downtilt Range 0-10° 0-12° 0-12°
Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio > 25 dB > 25 dB > 25 dB
Maximum Power (Per Port) 200 W 160 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5880200A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5880200G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
8 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2690 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 24 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 160 km/h (EN1991-4-1) Frontal: 607 N Lateral: 510 N Rear: 944 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Wall mounting brackets with azimuth pan 0900183/00 1.6 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900885/00 3.3 kg
790-960 / 1710-2170 / 1710-2170 MHz
58802005880200A 5880200G
Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Packaging
Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 35 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 790-960 MHz
WHITE 1710-2170 MHz
BLUE 1710-2170 MHz
April 2015 | 9
698-960 / 1695-2690 MHz
58613005861300A 5861300G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt
• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10° / 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
SlimLineLTE Ready
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5861300
Remote Electrical Tilt AISG1.1 5861300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5861300G
Access Ports Description (Connectors)
The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Ultra Wide Band 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck
Electrical Characteristics R1 Y1
Frequency Bands (MHz) 700 800 900 1800 2100 2600
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
15.515.515.2
16.516.416.2
17.417.317.0
17.717.717.7
18.118.118.0
18.518.518.2
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61°
Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 6.1° 5.3° 4.2°
Electrical Downtilt Range 0-10° 0-10°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5861300A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5861300G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
R1
Y1
10 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2688 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 24 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 761 N Lateral: 348 N Rear: 747 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900393/00 5.1 kg
Brackets for pole 70 to 150 mm 0900501/00 5.8 kg
Kit to add mechanical tilt (0-10°) to above brackets
0900394/00 3.1 kg
Wall mounting brackets with azimuth pan 0900395/00 2.3 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900533/00 4.4 kg
698-960 / 1695-2690 MHz
58613005861300A 5861300G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt
Packaging
Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 28.5 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna
Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 698-960 MHz
YELLOW 1695-2690 MHz
April 2015 | 11
790-960 / 1710-2170 MHz
58612005861200A 5861200G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.9 dBi | Variable Tilt
• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10° / 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
SlimLineSeries
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5861200
Remote Electrical Tilt AISG1.1 5861200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5861200G
Access Ports Description (Connectors)
The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.
RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Long Neck
BLUE Rings High Band 1710-2170 MHz Ports (Wide Band) (2x) 7/16-DIN Long Neck
Electrical Characteristics Low Band (RED) High Band (BLUE)
Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
16.2...16.8...17.516.2...16.8...17.516.0...16.7...17.4
18.2...18.518.0...18.317.8...18.0
18.5...18.918.3...18.718.0...18.1
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 65° 65° 64°
Vertical Beamwidth (-3 dB) 7° 5° 4.5°
Electrical Downtilt Range 0-10° 0-10°
Isolation Between Ports > 25 dB > 30 dB, > 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio > 30 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5861200A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5861200G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
12 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2690 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 25 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 160 km/h Frontal: 580 N Lateral: 480 N Rear: 910 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt (0-10°) to above brackets
0900396/00 1.8 kg
Wall mounting brackets with azimuth pan 0900183/00 1.6 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900885/00 3.3 kg
790-960 / 1710-2170 MHz
58612005861200A 5861200G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.9 dBi | Variable Tilt
Packaging
Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 33 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 790-960 MHz
BLUE 1710-2170 MHz
April 2015 | 13
790-960 MHz
58202005820200A 5820200G
Single Band | Panel Antenna | X-Pol | 65° | 17.5 dBi | Variable Tilt
• Single band antenna, dual polarisation, 2 connectors • Variable electrical tilt 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • RET module fully inserted inside the antenna (field replaceable)
SlimLineSeries
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5820200
Remote Electrical Tilt AISG1.1 5820200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5820200G
Access Ports Description (Connectors)
The antenna has 2 connectors located at the bottom face. See image on the following page.
RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Electrical Characteristics
Frequency Bands (MHz) 790...880...960
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
Input Impedance 50Ω
VSWR < 1.5
Polarisation ±45°
Horizontal Beamwidth (-3 dB) 72°...68°...65°
Vertical Beamwidth (-3 dB) 7°
Electrical Downtilt Range 0-10°
Isolation Between Ports > 25...30...30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical
Front-to-Back Ratio > 30 dB
Maximum Power (Per Port) 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5820200A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5820200G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
14 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2688 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 17 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 160 km/h 600 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900188/00 1.5 kg
Wall mounting brackets with azimuth pan 0900183/00 1.6 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900885/00 3.3 kg
790-960 MHz
58202005820200A 5820200G
Single Band | Panel Antenna | X-Pol | 65° | 17.5 dBi | Variable Tilt
Packaging
Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 25 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 790-960 MHz
April 2015 | 15
698-960 / 1695-2690 MHz
58633005863300A 5863300G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt
• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10° / 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
SlimLineLTE Ready
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5863300
Remote Electrical Tilt AISG1.1 5863300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5863300G
Access Ports Description (Connectors)
The antenna has 6 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Ultra Wide Band 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck
Electrical Characteristics R1 Y1
Frequency Bands (MHz) 700 800 900 1800 2100 2600
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
14.514.514.2
15.515.415.1
16.416.316.0
17.717.717.7
18.118.118.0
18.518.518.2
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61°
Vertical Beamwidth (-3 dB) 12° 10° 9.4° 6.1° 5.3° 4.2°
Electrical Downtilt Range 0-10° 0-10°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5863300A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5863300G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
R1
Y1
16 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 1914 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 17 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 542 N Lateral: 248 N Rear: 532 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900393/00 5.1 kg
Brackets for pole 70 to 150 mm 0900501/00 5.8 kg
Kit to add mechanical tilt (0-10°) to above brackets
0900394/00 3.1 kg
Wall mounting brackets with azimuth pan 0900395/00 2.3 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900533/00 4.4 kg
698-960 / 1695-2690 MHz
58633005863300A 5863300G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt
Packaging
Carton Box 2.12 x 0.35 x 0.24 m 0.178 m3 | 21.5 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCUfor RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna
Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 698-960 MHz
YELLOW 1695-2690 MHz
April 2015 | 17
790-960 MHz
58182005818200A 5818200G
Single Band | Panel Antenna | X-Pol | 65° | 16.5 dBi | Variable Tilt
• Single band antenna, dual polarisation, 2 connectors • Variable electrical tilt 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • RET module fully inserted inside the antenna (field replaceable)
SlimLineSeries
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5818200
Remote Electrical Tilt AISG1.1 5818200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5818200G
Access Ports Description (Connectors)
The antenna has 2 connectors located at the bottom face. See image on the following page.
RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Electrical Characteristics
Frequency Bands (MHz) 790...880...960
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
15.5...16.0...16.515.5...16.0...16.515.4...15.9...16.4
Input Impedance 50Ω
VSWR < 1.5
Polarisation ±45°
Horizontal Beamwidth (-3 dB) 72°...68°...65°
Vertical Beamwidth (-3 dB) 9°
Electrical Downtilt Range 0-10°
Isolation Between Ports > 25...30...30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical
Front-to-Back Ratio > 25 dB
Maximum Power (Per Port) 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5818200A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5818200G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
18 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 1910 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 13 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 413 N Lateral: 347 N Rear: 649 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900188/00 1.5 kg
Wall mounting brackets with azimuth pan 0900183/00 1.6 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900885/00 3.3 kg
790-960 MHz
58182005818200A 5818200G
Single Band | Panel Antenna | X-Pol | 65° | 16.5 dBi | Variable Tilt
Packaging
Carton Box 2.13 x 0.35 x 0.24 m 0.180 m3 | 20 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 790-960 MHz
April 2015 | 19
698-960 / 1695-2690 MHz
58293005829300A 5829300G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 15.0 / 18.0 dBi | Variable Tilt
• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-12° / 0-12°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
SlimLineLTE Ready
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5829300
Remote Electrical Tilt AISG1.1 5829300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5829300G
Access Ports Description (Connectors)
The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Ultra Wide Band 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck
Electrical Characteristics R1 Y1
Frequency Bands (MHz) 700 800 900 1800 2100 2600
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
13.013.012.8
14.013.913.6
14.914.814.5
17.117.117.1
17.517.517.4
18.018.017.8
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61°
Vertical Beamwidth (-3 dB) 16.8° 14.0° 13.2° 7.0° 6.4° 5.2°
Electrical Downtilt Range 0-12° 0-12°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5829300A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5829300G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
R1
Y1
20 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 1358 x 253 x 147 mm
Weight (Excluding Mounting Accessories) 13 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 385 N Lateral: 176 N Rear: 378 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900393/00 5.1 kg
Brackets for pole 70 to 150 mm 0900501/00 5.8 kg
Kit to add mechanical tilt (0-10°) to above brackets
0900394/00 3.1 kg
Wall mounting brackets with azimuth pan 0900395/00 2.3 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900533/00 4.4 kg
698-960 / 1695-2690 MHz
58293005829300A 5829300G
Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 15.0 / 18.0 dBi | Variable Tilt
Packaging
Carton Box 1.57 x 0.35 x 0.24 m 0.132 m3 | 17.5 kg
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna
Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 698-960 MHz
YELLOW 1695-2690 MHz
April 2015 | 21