Palladian Gazebo Assembly Instructions and Owner’s Manual

PC-10053

Assembly Instructi ons andOwner’s Manual

Palladian Gazebo

Agora Outdoor LivingTM

Design and Manufacture byPacifi c Currents Inc.

Gazebo Replacement Canopy


http://www.garden-lawnmower.com/10x10-replacement-gazebo-canopy/



2 PC-10053

***Important*** For missing or defective parts, Do NOT return to the place of purchase. Call the toll free number below or visit www.pacifi ccurrents.com. Please have your sales

receipt ready when you call. 888-474-2770

Part # Qty Description Part # Qty DescriptionA 4 Corner Panel - A J 4 Top Bar (110 cm)B 4 Corner Panel - B K 4 Top Bar (109 cm)C 4 Corner Connector L 16 Bolt (52 mm)D 1 Top Connector M 116 NutE 4 Crossbar Sleeve Connector N 232 Steel WasherF 16 Lawn Stake O 8 Roof Support BarG 4 Top Cross Bar P 116 Plastic Nut CapH 4 Top Cross Bar Q 8 Bolt (42 mm)I1 4 Vent Opening Support Bar R 76 Bolt (32 mm)I2 4 Vent Opening Support Bar S 16 Bolt (25 mm)I3 4 Vent Opening Support Bar

Parts ListGazebo Replacement Canopy



PC-10053 3

First, compare the parts in the box with the parts list on the following pages and make sure that none are missing. If you discover any missing parts, please visit www.pacifi ccurrentsinc.com or call 888-474-2770. Save your sales receipt as you will need this to obtain service.

Choose and measure the fi nal locati on where you would like to place the prod-uct and ensure that it will fi t a 10’ x 10’ rectangle with 11’ height clearance. Then, choose an assembly area as close as possible to this fi nal locati on and large enough to layout and pre-assemble all the parts for this Gazebo.

It is highly recommended that you cover the work surface with a tarp or other fabric to prevent scratches to the fi nish during assembly.

You will need these additi onal tools: a ladder and an adjustable wrench.

You may also need these additi ontal tools (opti onal): work gloves, waterproofi ng spray.

Prepare the work area:

General Notes:

Pre-Assembly Steps

Thank you for choosing a Pacifi c Currents Product. Please make sure you have carefully read and understood

these assembly instructions before you begin.

1. You will need the help of another person to assemble this product. Please ask a friend or neighbor for assistance!

2. Once a unit has been pre-assembled in each step, please set it aside unti l further instructi ons.

3. For all customers, we highly recommend that you remove your canopy top in cases of severe inclement weather such as thunderstorms. Please exercise good judgement.

4. Do not completely ti ghten any bolts or nuts unti l the last step prior to att aching the canvas top as you may need to make adjustments in the positi on of parts.



4 PC-10053

Step 1

A) Attach one Part A to one Part B at the corner to form an L shape.

B) Thread one Part Q bolt through a Part N washer, the aligned holes in the panels, another Part Q washer, and one Part M nut. Loosely tighten.

C) Repeat step B for the other hole in the panels.

D) Repeat steps A through C for the three remaining sets of corner panels.

Parts you will need:

4 Corner Panels A (Part A) 16 Steel Washers (Part N)4 Corner Panels B (Part B) 8 Steel Nuts (Part M)8 40mm Bolts (Part Q)

Assembly Instructi ons

Assemble the Four Gazebo Corner Legs

Step 2Parts you will need:

4 Cross Bar Connectors (Part G) 16 32mm Bolts (Part R)4 Cross Bar Connectors (Part H) 32 Steel Washers (Part N)4 Cross Bar Link Connectors (Part E) 16 Steel Nuts (Part M)

Assemble the Four Cross Bar Connectors



PC-10053 5

Step 4

A) Connect one Part G and one Part H together with one Part E to form a straight bar.

B) Loosely tighten four Part R bolts and Part N washers into Part E, followed by more Part N washers and part M nuts.

C) Repeat steps A through B for the three (3) remaining sets of roof connectors.

A) Connect one Part J to one Part K to form a straight bar.

B) Loosely connect the two bars by tighten-ing two Part R bolts and Part N washers into the aligned holes, followed by more Part N washers and part M nuts.

C) Repeat steps A and B for the seven (3) remaining sets of Roof connectors.

At this point, please put all the gazebo legs in an upright position over the fi nal location you have chosen for the gazebo and gather the remaining assembled pieces from steps 2-4.

*Remember, please do not tighten any of the nuts all the way as this will hinder the fi nal assembly.


4 Top Bars (Part J) 16 Steel Washers (Part N)4 Top Bars (Part K) 8 Steel Nuts (Part M)8 32mm Bolts (Part R)

Assemble Top Roof Bars

Gather the pre-assembled parts



6 PC-10053

A) Connect one Gazebo leg panel with one cross bar connector and one corner connector by threading a Part L bolt and Part N washer into the aligned holes fol-lowed by another Part N washer and loosely tighten a part M nut.

B) Repeat step A for the remaining 7 corner panels.

C) Keep all connections loose to allow for adjustments.


4 Assembled Gazebo Legs (Step 1) 16 52mm Bolts (Part L)4 Assembled Cross Bar Connectors (Step 2) 32 Steel Washers (Part N)4 Top Corner Connectors (Part C) 16 Steel Nuts (Part M)

Attach Gazebo Legs to Cross Bar Connectors




PC-10053 7

A) Connect two corner bars (Step 3) to the Top Connector Part D to form a triangu-lar shape.

B) Insert one end of the assembly from step A to one corner connector Part C, then the other end into the opposite corner connector Part C.

C) Loosely fasten the three parts together and to the Gazebo frame with Part R bolts, Part N washers, and Part M nuts.

D) Repeat step A and B for the remaining 3 connector sides.


8 Assembled Corner Bars (Step 3) 24 Steel Washers (Part N)1 Top Connector (Part D) 12 Steel Nuts (Part M)12 32mm Bolts (Part R)

AttachTop Bars and Top Connectors to Gazebo Frame



8 PC-10053


8 Roof Support Bars (Part O) 24 32mm Bolts (Part R)48 Steel Washers (Part N) 24 Steel Nuts (Part M)

Assemble the Gazebo Vents

A) Connect one roof support bar Part O to the gazebo frame and top connector.

B) Loosely fasten the parts with 3 Part R bolts, 6 Part N washers, and 3 part M nuts per support bar.

C) Repeat Steps A and B for the seven remaining vent support bars.



PC-10053 9

A) Connect one each of Parts I1 and I2 to one Gazebo roof vent as shown, using 4 Part R bolt assemblies.

B) Connect Parts I1 and I2 us-ing 1 part I3 using 4 part S Bolt Assemblies.

C) Repeat steps A and B for the remaining 3 vent support bars.

Your gazebo should now resemble the image to the left. Please check to make sure all parts are in their

respective locations.

Step 8

Parts you will need:

4 Vent Opening Support Bars (Part I1) 16 32mm Bolts (Part R)4 Vent Opening Support Bars (Part I2) 16 25mm Bolts (Part S)4 Vent Opening Support Bars (Part I3) 64 Steel Washers (Part N)1 Assembled Gazebo Roof Top (Step 7) 32 Steel Nuts (Part M)

Attach Vent Support Bars to Gazebo Roof

S

I2

I1I3

R R

RR



10 PC-10053

You may use Part F to help secure the gazebo to fi rm, compacted, earth. Drive the stakes all the way into the ground at opposing angles (see fi g. 9) through pre-drilled holes in each corner panel.

NOTE: the spikes are not intended to permanently mount the gazebo to any surface nor are they meant for use in soft earth. If your gazebo is located on a wood or concrete patio, please visit your local hardware store for an appropriate solution.

Step 9

Step 10

You may tighten all bolts and nuts in the gazebo frame at this time. Tighten just enough so that the parts are no longer loose. Caution! Do not overtighten as this may bend or damage the steel frame. Plastic end caps are also provided to protect the nuts at each con-nection. You may attach those at this time.

Carefully pull the canvas top over the gazebo roof frame and slide the vent bars into each respective vent opening in the canvas. The fi t will be very snug. You may need to reposition the gazebo legs slightly in order to pull the canvas top into position. Use the velcro straps to secure the canvas top to the gazebo frame.

If you purchased a bug screen, you may attach it now using the velcro straps provided.

Tighten all Nuts and Bolts

Attach Canvas Top and/or Bug Screen


16 Lawn Stakes (Part F)

Lawn Stakes




PC-10053 11

FAQ (Frequently Asked Questi ons)

Q: Will the gazebo frame ever rust?

A: The powder coated fi nish of the metal frame prevents rusti ng so long as the metal itself is not exposed. Exposure of the metal may occur due to accidental scratches or long-term wear and tear. Occasional touch ups to aff ected areas with weatherproof paint will ensure many years of conti nued enjoyment from your gazebo.

Q: Can I use grills or barbecues inside the gazebo?

A: No, we do not recommend this. While the canopy top is fabricated using a fi re resistant material, our gazebos are not designed to accomodate an open fl ame. Please refrain from using your grill inside the gazebo.

Q: Will the gazebo move or blow away in strong winds?

A: Several features of our design were considered to allow the gazebo to remain very stable across a range of weather conditi ons. The four vents in the canopy top help to allow low to medium winds to pass through the covering.

However, if you install the gazebo in an area where strong winds are persistent, it is advisable to take further steps to fasten the gazebo to the ground. If the gazebo is installed over a soft natural surface (grass or dirt), you may drive metal stakes (included) through the holes located at the bott om of the panels and into the ground. If the gazebo is installed over a hard surface (wooden decks or concrete pati os) it will be necessary to separately purchase screws or bolts and nuts to affi x the frame to your installati on surface. Please visit your local Mills Fleet Farm Store for more opti ons.

Q: I like being outdoors, but cannot stay for long because of mosquitoes. Are bug screens available for my gazebo?

A: Yes! Bug screens for all gazebo models are available separately for purchase as an accessory.



12 PC-10053

Care Instructions:Canvas Top

The polyester top (Canvas Top) can be machine washed using a small amount of detergent. Do not machine dry or use bleach for the Top. Top may also be spray-rinsed while attached to Gazebo and lightly scrubbed with a soft broom. DO NOT use any hard abrasives to scrub.

The canvas top is not waterproof. However, a waterproofi ng spray (not included) may be used to prevent rain water infi ltration.

The canvas top MUST be removed and stored in a dry location in the event of snow fall. Accumulated snow WILL severely damage your gazebo if the canvas top is not removed.

Gazebo Frame

Any rust on the frame as a result of scratches on the surface can be cleaned with soap and water and wiped down with a soft cloth. DO NOT use any hard abrasives to scrub. Touch-up paint is not available but the colors can be matched at your local Mills Fleet Farm store.

All metal parts may be sprayed with a clear laquer fi nish to maintain the attractiveness of your gazebo over time and allow you to enjoy your gazebo for as long as possible.

IMPORTANT: Winter storage - If you live in an area that experiences snow in the winter, remove the canvas top and store it in a location that is dry and free of moisture.

1 Year Limited Warranty:Purchaser assumes all risk in the assembly and use of this unit.

All components carry a one year limited warranty from date of purchase against defects in material and workmanship arising under normal use. This warranty does not cover wear and tear, nor weathering due to climate and other environmental factors, nor does it cover failure resulting from accident, misuse, neglect , mishandling, modifi cation, or damage that is attributed to acts of nature. This warranty does not cover incidental or consequential damages resulting from use of product, or losses arising out of any breach of this warranty. Fulfi llment of this warrant shall only include direct replacement of or defective allowance with place of purchase of parts damaged inside original packaging while in transit to be arranged at the discretion of Pacifi c Currents Inc.

This warranty only extends to the original purchaser. Proof of purchase (such as sales receipt) will be required before warranty performance is rendered.

Please contact us should you have any questions concerning assembly, care information, warranty coverage, and missing or defective parts.

Customer Service:888-474-2770

Email: info@pacifi ccurrentsinc.com

Website: www.pacifi ccurrentsinc.com

Enjoy your new gazebo and thank you for choosing a Pacifi c Currents Inc. product!



Palladian Gazebo Assembly Instructions and Owner’s Manual

Business

Transcript of Palladian Gazebo Assembly Instructions and Owner’s Manual