Pages 3 from 2014F150 Owners 03_2014-3

8/19/2019 Pages 3 from 2014F150 Owners 03_2014-3

1/21

Integrated Keyhead Transmitter

1. Twist a thin coin in the slot of the

transmitter near the key ring to removethe battery cover.

2. Carefully peel up the rubber gasketfrom the transmitter. It may come offwith the battery cover.

3. Remove the old battery

4. Insert the new battery. Refer to theinstructions inside the transmitter forthe correct orientation of the battery.Press the battery down to make sure

it is fully in the housing.5. Reinstall the rubber gasket.

6. Snap the battery cover back onto thetransmitter.

Memory Feature (If Equipped)

You can use the remote control to recallmemory settings for the driver seat, powermirrors, steering column and power footpedals.

Press the unlock button on the remotecontrol to recall the memory positions. Ifyou enable the easy-entry and exit feature,the seat will move to the easy-entryposition. The seat will move to the drivermemory position when you put the key inthe ignition.

Programming to the Transmitter

1. With the ignition on, move the memoryfeatures to the desired positions using

the associated controls.

2. Press and hold memory button 1 on theside of the driver seat. A tone will soundafter about two seconds. Continue tohold until you hear a second tone.

3. Press the lock button on the remotecontrol within three seconds. A singletone sounds.

Repeat this procedure with button 2 and

a second remote control if desired.

Deactivating from the Transmitter

1. Press and hold the desired memorybutton for five seconds. A tone willsound after about two seconds.Continue to hold until you hear asecond tone.

2. Press the unlock button on the remotecontrol within three seconds.

Repeat this procedure for each additionaltransmitter if desired.

Car Finder

Press the button twice withinthree seconds. The horn willsound and the turn signals will

flash. We recommend you use this methodto locate your vehicle, rather than usingthe panic alarm.

50

F150 (TF6) , enUSA

Keys and Remote Controls


2/21

Sounding a Panic Alarm

Note: The panic alarm will only operatewhen the ignition is off.

Press the button to activate thealarm. Press the button again orturn the ignition on to deactivate

it.

Remote Start (If Equipped)

WARNING

To avoid exhaust fumes, do not useremote start if your vehicle is parked

indoors or areas that are not wellventilated.

Note: Do not use remote start if your vehicleis low on fuel.

The remote start button is on thetransmitter.

This feature allows you to start yourvehicle from outside the vehicle. The

transmitter has an extended operatingrange.

Vehicles with automatic climate controlcan be set to operate when you remotestart the vehicle. See Climate Control(page 106). A manual climate controlsystem will run at the setting it was set towhen you switch the vehicle off.

Many states and provinces haverestrictions for the use of remote start.Check your local and state or provinciallaws for specific requirements regardingremote start systems.

The remote start system will not work ifany of the following occur:

• The ignition is on.

• The alarm system triggers.

• You disable the feature.

• The hood is open.

• The transmission is not in P.

• The vehicle battery voltage is too low.

• The service engine soon indicator is on.

Remote Starting the Vehicle

Note: You must press each button withinthree seconds of each other. Your vehiclewill not remote start and the horn will not sound if you do not follow this sequence.

The label on your transmitter details thestarting procedure.

To remote start your vehicle:

1. Press the lock button to lock all thedoors.

2. Press the remote start button twice.The exterior lamps will flash twice.

The horn will sound if the system fails tostart, unless quiet start is on. Quiet startwill run the blower fan at a slower speedto reduce noise. You can switch it on or offin the information display. See GeneralInformation (page 87).

Note: If you remote start your vehicle with an integrated keyhead transmitter, you must

switch the ignition on before driving your vehicle. If you remote start your vehicle with an intelligent access transmitter, you must press the START/STOP button on theinstrument panel once while applying the brake pedal before driving your vehicle.

The power windows will not work duringthe remote start and the radio will not turnon automatically.

51

F150 (TF6) , enUSA


http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


3/21

The parking lamps will remain on and thevehicle will run for 5, 10, or 15 minutes,depending on the setting.

Extending the Vehicle Run Time

Repeat Steps 1 and 2 with the vehicle stillrunning to extend the run time for anotherremote start duration. If the duration is setto last 10 minutes, the duration will extendby another 10 minutes. For example, if thevehicle had been running from the firstremote start for five minutes, the vehiclewill continue to run now for a total of 20minutes.

Wait at least five seconds before remotestarting after a vehicle shutdown.

Turning the Vehicle Off After Remote Starting

Press the button once. Theparking lamps will turn off.

You may have to be closer to thevehicle than when starting due to groundreflection and the added noise of therunning vehicle.

You can disable or enable the remote startsystem through the information display.See General Information (page 87).

REPLACING A LOST KEY ORREMOTE CONTROL

Replacement keys or remote controls canbe purchased from an authorized dealer.

Authorized dealers can program remotecontrols for your vehicle. See PassiveAnti-Theft System (page 61).

To re-program the passive anti-theftsystem see an authorized dealer.

52

F150 (TF6) , enUSA


http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


4/21

PRINCIPLE OF OPERATION

MyKey allows you to program keys withrestricted driving modes to promote gooddriving habits. All but one of the keysprogrammed to the vehicle can beactivated with these restricted modes.

Any keys that have not been programmedare referred to as administrator keys oradmin keys. They can be used to:

• create a MyKey

• program configurable MyKey settings

• clear all MyKey features.

When you have programmed a MyKey, youcan access the following information usingthe information display:

• How many admin keys and MyKeys areprogrammed to your vehicle.

• The total distance your vehicle hastraveled using a MyKey.

Note: All MyKeys are programmed to the same settings. You cannot program themindividually.

Non-configurable Settings

The following settings cannot be changedby an admin key user:

• Belt-Minder. You cannot disable thisfeature. The audio system will mutewhen the front seat occupants’ safetybelts are not fastened.

• Early low fuel. The low fuel warning isactivated earlier, giving the MyKey user

more time to refuel.• Driver assist features, if equipped on

your vehicle, are forced on: parking aid,blind spot information system (BLIS)with cross traffic alert, lane departurewarning and forward collision warningsystem.

• Satellite radio adult contentrestrictions.

Configurable Settings

With an admin key, you can configurecertain MyKey settings when you first

create a MyKey and before you recycle thekey or restart the vehicle. You can alsochange the settings afterward with anadmin key:

• A vehicle speed limit can be set.Warnings will be shown in the displayfollowed by an audible tone when yourvehicle reaches the set speed. Youcannot override the set speed by fullydepressing the accelerator pedal or bysetting cruise control.

• Vehicle speed minders of 45, 55 or 65mph (75, 90 or 105 km/h). Once youselect a speed, it will be shown in thedisplay, followed by an audible tonewhen the preselected vehicle speed isexceeded.

• Audio system maximum volume of45%. A message will be shown in thedisplay when you attempt to exceedthe limited volume. Also, thespeed-sensitive or compensatedautomatic volume control will bedisabled.

• Always on setting. When this isselected, you will not be able to turnoff Advance Trac (if your vehicle isequipped with this feature).

CREATING A MYKEY

Use the information display to create a

MyKey. There are two types of informationdisplays, and their controls and messagingvary. To determine which type of displayyou have, you will need to referenceanother chapter. See GeneralInformation (page 87).

If You Have a Type 1 InformationDisplay:

53

F150 (TF6) , enUSA

MyKey ™

http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


5/21

1. Insert the key you want to program intothe ignition.

2. Switch the ignition on.

3. Access the main menu on theinformation display controls. PressSETUP using the information displaybuttons until PRESS RESET TOCREATE MYKEY is displayed.

4. Press and release the RESET button.You will see HOLD RESET TOCONFIRM MYKEY in the display.

5. Press and hold the RESET button fortwo seconds until you see the messageMARK THIS AS RESTRICTED in thedisplay. Wait until you see KEYRESTRICTED AT NEXT START in thedisplay.


1. Insert the key you want to program intothe ignition.

2. Switch the ignition on.

3. Access the main menu on the

information display controls, and selectSETTINGS, then MYKEY by pressingOK or the > button.

4. Press OK or the > button to selectCREATE A MYKEY.

5. When prompted, hold the OK buttonuntil you see KEY RESTRICTED ATNEXT START in the display. The keywill be restricted at the next start.

MyKey is successfully created. Make sure

you label it so you can distinguish it fromthe admin keys.

You can also program configurablesettings for the key(s). Refer toProgramming/Changing ConfigurableSettings.

Programming/ChangingConfigurable Settings

Use the information display to program or

change your configurable MyKey settings.There are two types of informationdisplays, and their controls and messagingvary. To determine which type of displayyou have, you will need to referenceanother chapter. See GeneralInformation (page 87).


1. Switch the ignition on using an admin

key.2. Access the main menu on the

information display controls, and pressSETUP until RESET FOR MYKEYSETTINGS displays.

3. Press and release the RESET buttonto display MyKey setup menus.

4. Press the SETUP button to enter yourchoice. Once you make a selection, thenext configurable setting will bedisplayed.

5. Repeat Steps 3 and 4 until you aredone changing the configurablesettings.


1. Switch the ignition on using an adminkey.

2. Access the main menu on theinformation display controls, and select

SETTINGS, then MYKEY by pressingOK or the > button.

3. Use the arrow buttons to get to aconfigurable feature.

4. Press OK or > to make a selection.

54

F150 (TF6) , enUSA

MyKey ™



6/21

Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. Once you have switched the engine off, however, you

will need an admin key to change or clear your MyKey settings.

CLEARING ALL MYKEYS

You can clear all MyKeys within the samekey cycle as you created the MyKey. If youswitch your ignition off, however, you willneed to use an admin key to clear yourMyKeys.

Note: When you clear your MyKeys, you remove all restrictions and return all MyKeysto their original admin key status at once.

To clear all MyKeys of all MyKey settings,use the information display. There are twotypes of information displays, and theircontrols and messaging vary. To determinewhich type of display you have, you willneed to reference another chapter. SeeGeneral Information (page 87).


1. Press SETUP until PRESS RESET TOCLEAR MYKEY displays.

2. Press and release the RESET button.The display will show HOLD RESETTO CONFIRM CLEAR.

3. Press and hold the RESET button fortwo seconds until ALL MYKEYSCLEARED displays.


1. Access the main menu and selectSETTINGS, then MYKEY.

2. Scroll to CLEAR ALL and press the OKbutton.

3. Hold the OK button until ALLMYKEYS CLEARED displays.

CHECKING MYKEY SYSTEMSTATUS

You can find information about yourprogrammed MyKeys by using theinformation display.

MYKEY DISTANCE

Tracks the distance when drivers use aMyKey. The only way to delete theaccumulated distance is by using an admin

key to clear your MyKey. If the distancedoes not accumulate as expected, thenthe intended user is not using the MyKey,or an admin key user recently cleared andthen recreated a MyKey.

NUMBER OF MYKEY(S)

Indicates the number of MyKeysprogrammed to your vehicle. Use thisfeature to detect how many MyKeys youhave for your vehicle and determine when

a MyKey has been deleted.NUMBER OF ADMIN KEY(S)

Indicates how many admin keys areprogrammed to your vehicle. Use thisfeature to determine how manyunrestricted keys you have for your vehicle,and detect if an additional MyKey has beenprogrammed.

USING MYKEY WITH REMOTE

START SYSTEMS

MyKey is not compatible with nonFord-approved, aftermarket remote startsystems. If you choose to install a remotestart system, see an authorized dealer fora Ford-approved remote start system.

55

F150 (TF6) , enUSA

MyKey ™

http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


7/21

MYKEY TROUBLESHOOTING

Potential causesCondition

· The key used to start the vehicle does nothave admin privileges.

I cannot create a MyKey.

· The key used to start the vehicle is the onlyadmin key. There always has to be at leastone admin key.· SecuriLock passive anti-theft system isdisabled or in unlimited mode.

· The key in the ignition does not have adminprivileges.

I cannot program the configurable settings.

· There are no keys programmed to the

vehicle. See Creating a MyKey (page 53).

· The key used to start the vehicle does nothave admin privileges.

I cannot clear the MyKeys.

· No MyKeys are created. See Creating aMyKey (page 53).

· Purchase a new key from your authorizeddealer.

I lost the only admin key.

· Program a spare key. See Passive Anti-Theft System (page 61).

I lost a key.

· The MyKey user is not using the MyKey.MyKey distances do not accumulate.· An admin key holder cleared the MyKeysand created new MyKeys.· The key system has been reset.

56

F150 (TF6) , enUSA

MyKey ™

http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


8/21

LOCKING AND UNLOCKING

You can use the power door lock controlor the remote control to lock and unlockyour vehicle.

Power Door Locks (If Equipped)

The power door lock control is on the driverand front passenger door panels.

UnlockA

LockB

Remote Control (If Equipped)

You can use the remote control at any timeyour vehicle is not running.

Unlocking the Doors (Two-StageUnlock)

Press the button to unlock thedriver door.

Press the button again withinthree seconds to unlock all doors. The turnsignals will flash.

Press and hold both the lock and unlockbuttons on the remote control for fourseconds to disable or enable two-stageunlocking. Disabling two-stage unlockingallows all vehicle doors to unlock with onepress of the button. The turn signals willflash twice to indicate a change to theunlocking mode. The unlocking modeapplies to the remote control and keylessentry keypad.

Locking the Doors

Press the button to lock all thedoors. The turn signals will

illuminate.Press the button again within threeseconds to confirm that all the doors areclosed. The doors will lock again, the hornwill sound and the turn signals willilluminate if all the doors are closed.

Mislock

If any door is open or if the hood is open onvehicles with an anti-theft alarm or remote

start, the horn will sound twice and thelamps will not flash.

Smart Unlocks (If Equipped)

This feature helps to prevent you fromlocking yourself out of your vehicle if yourkey is still in the ignition.

When you open the driver door and lockyour vehicle with the power door lockcontrol, all the doors will lock then unlock

if your key is still in the ignition.Your can still lock your vehicle with the keyin the ignition by:

• using the manual lock on the door

• locking the driver door with a key

• using the keyless entry keypad

• using the lock button on the remotecontrol

Autolock and Autounlock (If Equipped)

The autolock feature will lock all the doorswhen:

• all doors are closed, and

• the ignition is on, and

• you shift into any gear putting yourvehicle in motion, and

• your vehicle attains a speed greaterthan 12 mph (20 km/h).

57

F150 (TF6) , enUSA

Locks


9/21

The autolock feature will unlock all thedoors when:

• autolock has locked the doors

•you stop the vehicle and switch theignition off or to accessory mode, and

• you open the driver door within 10minutes.

Note: The doors will not autounlock if you have electronically locked them beforeopening the driver door.

Enabling or Disabling

You can enable or disable these features

in the information display or yourauthorized dealer can do it for you. SeeGeneral Information (page 87).

Note: You can enable or disable the autolock and autounlock featuresindependently of each other.

Illuminated Entry

The interior lamps and select exteriorlamps will illuminate when you unlock the

doors with the remote entry system.The illuminated entry system will turn offthe lights if:

• the ignition is on

• you press the remote control lockbutton, or

• after 25 seconds of illumination.

The dome lamp will not turn on if thecontrol is set to the off position.

The lights will not turn off if:• you turn them on with the dimmer

control, or

• any door is open.

Battery Saver

The battery saver turns off the interiorlamps 30 minutes after you switch the

ignition off if a door is open and the domelamp switch is on. It turns off the interiorlamps after 10 minutes if the dome lampswitch is off.

KEYLESS ENTRY (IF EQUIPPED)

SECURICODE™ KEYLESS ENTRYKEYPAD

The keypad is located near the driver

window.

Note: If you enter your entry code too faston the keypad, the unlock function may notwork. Re-enter your entry code more slowly.

You can use the keypad to lock or unlockthe doors without using a key.

You can operate the keypad with thefactory-set five-digit entry code. The codeis located on the owner’s wallet card in theglove box and is available from anauthorized dealer. You can also create upto five of your own five-digit personal entrycodes.

Programming a Personal Entry Code

To create your own personal entry code:

1. Enter the factory-set code.

2. Press 1·2 on the keypad within fiveseconds.

58

F150 (TF6) , enUSA

Locks



10/21

3. Enter your personal 5-digit code. Youmust enter each number within fiveseconds of each other.

4. Press 1·2 on the keypad to savepersonal code 1.

The doors will lock then unlock to confirmthat programming was successful.

To program additional personal entrycodes, repeat Steps 1-3, then for Step 4:

• Press 3·4 to save personal code 2.

• Press 5·6, 7·8 or 9·0 to save personalcode 3.

You may also program a personal entrycode through the MyFord Touch system.

Tips:

• Do not set a code that uses five of thesame number.

• Do not use five numbers in sequentialorder.

• The factory-set code will work even ifyou have set your own personal code.

Recalling Memory Positions (If

Equipped)

The programmed entry codes will recalldriver memory positions as follows:

• Entry code 1 will recall driver 1 memorypositions.

• Entry code 2 will recall driver 2 memorypositions.

Note: Personal entry codes 3, 4 and 5 will not recall memory positions.

Erasing a Personal Code

1. Enter the factory-set 5-digit code.

2. Press and release 1·2 on the keypadwithin five seconds.

3. Press and hold 1·2 for two seconds.You must do this within five secondsof completing Step 2.

All personal codes will erase and only thefactory-set 5-digit code will work.

Anti-Scan Feature

The keypad will go into an anti-scan modeif you enter the wrong code seven times(35 consecutive button presses). Thismode disables the keypad for one minuteand the keypad lamp will flash.

The anti-scan feature will turn off after:

• One minute of keypad inactivity.

• Pressing the unlock button on theremote control.

•Switching the ignition on.

Unlocking and Locking the Doors

To Unlock the Driver Door

Enter the factory-set 5-digit code or yourpersonal code. You must press eachnumber within five seconds of each other.The interior lamps will illuminate.

Note: All doors will unlock if you disablethe two-stage unlocking mode. See

Locking and Unlocking (page 57).

To Unlock All Doors

Enter the factory-set code or your personalcode, then press 3·4 within five seconds.

To Lock All Doors

Press and hold 7·8 and 9·0 at the sametime (with the driver door closed). You donot need to enter the keypad code first.

Displaying the Factory Set Code

Note: You will need to have two programmed passive anti-theft keys for this procedure.

To display the factory-set code in theinformation display:

1. Insert a key into the ignition and switchthe ignition on for a few seconds.

59

F150 (TF6) , enUSA

Locks



11/21

2. Switch the ignition off and remove thekey.

3. Within ten seconds, insert the second

key into the ignition and switch theignition on.

The factory-set code will display for a fewseconds.

Note: The code may not display until after any other warning messages first display.

60

F150 (TF6) , enUSA

Locks


12/21

PASSIVE ANTI-THEFTSYSTEM (IF EQUIPPED)

Note: The system is not compatible with non-Ford aftermarket remote start systems.Use of these systems may result in vehicle starting problems and a loss of security protection.

Note: Metallic objects, electronic devicesor a second coded key on the same key chain may cause vehicle starting problemsif they are too close to the key when startingthe engine. Prevent these objects fromtouching the coded key while starting the

engine. Switch the ignition off, move allobjects on the key chain away from thecoded key and restart the engine if a problem occurs.

Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.

SecuriLock™

The system is an engine immobilization

system. It helps prevent the engine fromstarting unless you use a coded keyprogrammed to your vehicle. Using thewrong key may prevent the engine fromstarting. A message may appear in theinformation display.

If you are unable to start the engine with acorrectly coded key, the system hasmalfunctioned. A message may appear inthe information display.

Automatic Arming

The system arms immediately after youswitch the ignition off.

Automatic Disarming

Switching the ignition on with a coded keydisarms the system.

Replacement Keys

Note: Your vehicle may have two integrated keyhead transmitters.

The integrated keyhead transmitterfunctions as a programmed ignition key. Itoperates all the locks, starts the vehicleand acts as a remote control.

If your programmed transmitters orstandard SecuriLock coded keys are lostor stolen and you do not have an extracoded key, you will need to have yourvehicle towed to an authorized dealer. Youneed to erase the key codes from yourvehicle and program new coded keys.

Store an extra programmed key away fromyour vehicle in a safe place to help preventany inconveniences. See an authorizeddealer to purchase additional spare orreplacement keys.

Programming a Spare Key

Note: You can program a maximum of eightcoded keys to your vehicle. Only four of these can be integrated keyhead

transmitters.

You can program your own integratedkeyhead transmitter or standardSecuriLock coded keys to your vehicle. Thisprocedure will program both the engineimmobilizer keycode and the remote entryportion of the remote control to yourvehicle.

Only use integrated keyhead transmittersor standard SecuriLock keys.

You must have two previouslyprogrammed coded keys and the newunprogrammed key readily accessible. Seean authorized dealer to have the spare keyprogrammed if two previouslyprogrammed coded keys are not available.

Read and understand the entire procedurebefore you begin.

61

F150 (TF6) , enUSA

Security


13/21

1. Insert the first previously programmedcoded key into the ignition.

2. Switch the ignition from off to on. Keep

the ignition on for at least threeseconds, but no more than 10 seconds.

3. Switch the ignition off and remove thefirst coded key from the ignition.

4. After three seconds but within 10seconds of switching the ignition off,insert the second previously coded keyinto the ignition.

5. Switch the ignition from off to on. Keepthe ignition on for at least threeseconds, but no more than 10 seconds.

6. Switch the ignition off and remove thesecond previously programmed codedkey from the ignition.

7. After three seconds but within 10seconds of switching the ignition offand removing the previouslyprogrammed coded key, insert the newunprogrammed key into the ignition.

8. Switch the ignition from off to on. Keepthe ignition on for at least six seconds

until you hear the door locks cycle.

9. Remove the newly programmed codedkey from the ignition.

The key will start the engine ifprogramming is successful. You canoperate the remote entry system if the newkey is an integrated keyhead transmitter.

If programming was not successful, wait20 seconds and repeat Steps 1 through 8.If you are still unsuccessful, take your

vehicle to an authorized dealer.

ANTI-THEFT ALARM (IF EQUIPPED)

The system warns you of an unauthorizedentry to your vehicle. It triggers if any dooror the hood opens without using the key,remote control or keyless entry keypad.

The direction indicators flash and the hornsounds if the system triggers while thealarm is armed.

Take all remote controls to an authorizeddealer if there is any potential alarmproblem with your vehicle.

Arming the Alarm

The alarm is ready to arm when there isnot a key in the ignition. Electronically lockthe vehicle to arm the alarm.

The direction indicators flash once afteryou lock the vehicle. This indicates thealarm is in the pre-armed mode. It will fullyarm in 20 seconds.

Disarming the Alarm

Disarm the alarm by any of the followingactions:

• Press the power door unlock buttonwithin the 20-second pre-armed mode.

• Unlock the doors with the remotecontrol or keyless entry keypad.

•Switch the ignition on or start thevehicle.

• Use a key in the driver door to unlockthe vehicle, then switch the ignition onwithin 12 seconds.

Note: Pressing the panic button on the remote control will stop the horn and signalindicators, but will not disarm the system.

62

F150 (TF6) , enUSA

Security


14/21

USING POWER RUNNINGBOARDS

WARNINGSIn extreme climates, excessive icebuildup may occur, causing therunning boards not to deploy. Make

sure that the running boards havedeployed, and have finished moving beforeattempting to step on them. The runningboards will resume normal function oncethe blockage is cleared.

Turn off the running boards beforejacking or placing any object underyour vehicle. Never place your hand

between the extended running board andyour vehicle. A moving running board maycause injury.

Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board underbody mounts to lift your vehicle when jacking. Always use proper jacking points.

Note: The running boards may operate more slowly in cool temperatures.

Note: The running board mechanism may trap debris such as mud, dirt, snow, ice and salt. This may cause unwanted noise. If this happens, manually set the running boardsto the deployed position. Then, wash the system, in particular the front and rear hinge arms, with a high-pressure car wash wand.

Automatic Power Deploy

The running boards automatically extenddown and out when you open the door.This can help you enter and exit yourvehicle.

Automatic Power Stow

When you close the doors, the runningboards return to the stowed position aftera two-second delay.

Manual Power Deploy

You can manually operate the runningboards in the information display. SeeGeneral Information (page 87).

Set the running boards in the deployedposition (OUT) to access the roof.

The running boards return to the stowedposition and enter automatic mode whenthe vehicle speed exceeds 5 mph (8 km/h).

Enabling and Disabling

You can enable and disable the powerrunning board feature in the informationdisplay. See General Information (page87).

63

F150 (TF6) , enUSA

Power Running Boards (If Equipped)

http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


15/21

• When disabled (OFF), the runningboards move to the stowed positionregardless of the door position.

•

When enabled (AUTO), the runningboards move back to the correctpositions based on the door position.

Bounce-back

The running board will reverse directionand move to the end of travel if itencounters an object while moving.

64

F150 (TF6) , enUSA

Power Running Boards (If Equipped)


16/21

ADJUSTING THE STEERINGWHEEL

WARNINGDo not adjust the steering wheelwhen your vehicle is moving.

Note: Make sure that you are sitting in thecorrect position. See Sitting in the Correct

Position (page 114).

1. Unlock the steering column.

Note: The telescopic adjustment is anoptional feature.

2. Adjust the steering wheel to the desiredposition.

3. Lock the steering column.

Power Tilt and Telescope SteeringColumn (If Equipped)

WARNING

Do not adjust the steering wheelwhen your vehicle is moving.

Note: Make sure that you are sitting in thecorrect position. See Sitting in the Correct

Position (page 114).

65

F150 (TF6) , enUSA

Steering Wheel

http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


17/21

Use the control on the side of the steeringcolumn to adjust the position.

To adjust:

• tilt: press the top or bottom of thecontrol

• telescope: press the front or rear of thecontrol.

Memory Feature

You can save and recall the steeringcolumn position with the memory function.See Memory Function (page 118).

Pressing the adjustment control duringmemory recall cancels the operation. Thecolumn responds to the adjustmentcontrol.

Easy Entry and Exit Feature

The column moves to the full up and inposition when you switch the ignition off.It returns to the previous setting when youswitch the ignition on. You can enable ordisable this feature in the informationdisplay.

AUDIO CONTROL (IF EQUIPPED)

You can operate the following functions

with the control:Type 1

Volume upA

Seek up or nextB

MediaC

Seek down or previousD

Volume downE

Type 2

Volume upA

Seek up or nextB

MediaC

66

F150 (TF6) , enUSA

Steering Wheel

http://-/?-http://-/?-http://-/?-http://-/?-


18/21

Seek down or previousD

Volume downE

Media

Press repeatedly to scroll through availableaudio modes.

Seek, Next or Previous

Press the seek button to:

• Tune the radio to the next or previousstored preset.

• Play the next or previous track.

Press and hold the seek button to:

• Tune the radio to the next station upor down the frequency band.

• Seek through a track.

VOICE CONTROL (IF EQUIPPED)

Voice recognitionAPhone modeB

Confirm selectionC

See SYNC™ (page 323). See MyFordTouch™ (page 359).

CRUISE CONTROL (IF EQUIPPED)

See Cruise Control (page 176).

INFORMATION DISPLAYCONTROL

Type 1

Type 2

See Information Displays (page 87).

67

F150 (TF6) , enUSA

Steering Wheel

http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-


19/21

ADJUSTING THE PEDALS (IF

EQUIPPED)

Note: Never use the controls while your feet are on the accelerator and brake pedals and the vehicle is moving.

You can find the control on the left side ofthe steering column. Press and hold theappropriate side of the control to move thepedals.

A. Farther

B. CloserYou can save and recall the pedal positionswith the memory feature. See Memory Function (page 118).

Note: Adjust the pedals only when your vehicle is in P (Park).

68

F150 (TF6) , enUSA

Pedals



20/21

WINDSHIELD WIPERS

Note: Fully defrost the windshield before switching on the windshield wipers.

Note: Make sure you switch off thewindshield wipers before entering a car wash.

Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue,install new wiper blades.

Note: Do not operate the wipers on a dry windshield. This may scratch the glass,

damage the wiper blades or cause the wiper motor to burn out. Always use thewindshield washers before wiping a dry windshield.

Rotate the end of the control:

• Away from you to increase the wiperspeed.

• Toward you to decrease the wiperspeed.

Speed dependent wipers (ifequipped)

When your vehicle speed increases, theinterval between wipes decreases.

AUTOWIPERS (IF EQUIPPED)

Note: Make sure you switch off the wipers

before entering a car wash.Note: Wet or winter driving conditions withice, snow or salty road mist can causeinconsistent and unexpected wiping or smearing.

In these conditions, you can do thefollowing to help keep your windshieldclear:

• Lower the sensitivity of the autowipers.

• Change the wiper speed to normal or

high-speed wipe as necessary.• Switch the autowipers off.

The autowipers feature uses a rain sensor,located in the area around the interiormirror. The rain sensor monitors theamount of moisture on the windshield andautomatically turns on the wipers. It willadjust the wiper speed by the amount ofmoisture that the sensor detects on thewindshield. You can switch this feature onor off in the information display. SeeInformation Displays (page 87).

69

F150 (TF6) , enUSA

Wipers and Washers



21/21

Use the rotary control to adjust thesensitivity of the rain sensor. With lowsensitivity, the wipers will operate whenthe sensor detects a large amount of

moisture on the windshield. With highsensitivity, the wipers will operate whenthe sensor detects a small amount ofmoisture on the windshield.

Keep the outside of the windshield cleanbecause the rain sensor is very sensitive. Ifthe area around the interior mirror is dirty,then the wipers may turn on, for example,if dirt, mist or insects hit the windshield.

WINDSHIELD WASHERS

Note: Do not operate the wipers on a dry windshield. This may scratch the glass,damage the wiper blades or cause the wiper motor to burn out. Always use thewindshield washer before wiping a dry windshield.

Note: Do not operate the washers whenthe washer reservoir is empty. This may cause the washer pump to overheat.

• A brief press causes a single wipewithout washer fluid.

• A brief press and hold causes thewipers to swipe three times withwasher fluid.

• A long press and hold will turn on thewipers and washer fluid for up to 10seconds.

A wipe will occur a few seconds afterwashing to clear any remaining washerfluid. You can switch this feature on or offin the information display. See

Information Displays (page 87).

70

Wipers and Washers

Pages 3 from 2014F150 Owners 03_2014-3

Documents

Transcript of Pages 3 from 2014F150 Owners 03_2014-3