Packaging Vents - Gore...Vent housing: material HDPE HDPE HDPE HDPE PP PP PP Vent housing: color...
4
Concentrated or hazardous chemical formulations need packaging that breathes without leaking, to equalize pressure imbalances that would otherwise deform the container and cause dangerous spills or costly returns. GORE ® Packaging Vents minimize these risks with a breathable barrier membrane that reliably maintains container integrity – and consistently passes DOT and ADR requirements. Plug-In Vents • D38/D17/D15: Our most robust, reliable vents for the most aggressive industrial chemicals and “dangerous goods” packaging. Optimized for ADR Drop Test Specifications. • D15 Converse: For cartridges or other packaging that require exterior vent integration. Ideal for dosing/dispensing applications. • D10/D6: A high-performance, small-footprint vent designed to enhance safety, sustainability and savings in applications like dispensers for household or institutional cleaners. • D3: Equalizes pressure ONLY from the outside to the inside, for specialty applications including the smallest cartridges/ dispensers that don’t off-gas, but need pressure-balancing for product flow. Liners • NEW Foam Liners: Two Series, with full-surface membranes, for all flat-cap designs. Easy drop-in replacements for all single-point or unvented liners, in applications from consumer chemicals to DOT and ADR-regulated packaging. • Pulp Induction Liners: Two Series, for agrochemical bottles (up to 5 l). Weldable installation ensures tamper-evidence; membrane construction provides needed breathability for gas-scavenging chemicals and off-gassing liquids. Benefits of Plug-In Vents: • Meet the demanding needs of nearly all hazardous chemicals and cleaners. • D38/D17/D15 consistently demonstrate compliance with ADR test standards in varied container systems. • Easy to integrate via snap-fit or press-fit. Benefits of Liners: • Developed for fertilizer, pesticides and household chemicals and cleaners. • Easy to integrate without re-design of cap. • All liners are available in single- and multi-up roll goods as well as in various widths. NEW Prevent Leaks and Deformations and Enhance Container Safety for chemicals and cleaners Packaging V ents
Transcript of Packaging Vents - Gore...Vent housing: material HDPE HDPE HDPE HDPE PP PP PP Vent housing: color...
Concentrated or hazardous chemical formulations need packaging that breathes without leaking, to equalize pressure imbalances that would otherwise deform the container and cause dangerous spills or costly returns. GORE® Packaging Vents minimize these risks with a breathable barrier membrane that reliably maintains container integrity – and consistently passes DOT and ADR requirements.
Plug-In Vents
• D38/D17/D15: Our most robust, reliable vents for the most aggressive industrial chemicals and “dangerous goods” packaging. Optimized for ADR Drop Test Specifications.
• D15 Converse: For cartridges or other packaging that require exterior vent integration. Ideal for dosing/dispensing applications.
• D10/D6: A high-performance, small-footprint vent designed to enhance safety, sustainability and savings in applications like dispensers for household or institutional cleaners.
• D3: Equalizes pressure ONLY from the outside to the inside, for specialty applications including the smallest cartridges/dispensers that don’t off-gas, but need pressure-balancing for product flow.
Liners
• NEW Foam Liners: Two Series, with full-surface membranes, for all flat-cap designs. Easy drop-in replacements for all single-point or unvented liners, in applications from consumer chemicals to DOT and ADR-regulated packaging.
• Pulp Induction Liners: Two Series, for agrochemical bottles (up to 5 l). Weldable installation ensures tamper-evidence; membrane construction provides needed breathability for gas-scavenging chemicals and off-gassing liquids.
Benefits of Plug-In Vents:• Meet the demanding needs of nearly all hazardous
chemicals and cleaners.
• D38/D17/D15 consistently demonstrate compliance with ADR test standards in varied container systems.
• Easy to integrate via snap-fit or press-fit.
Benefits of Liners:• Developed for fertilizer, pesticides and household
chemicals and cleaners.
• Easy to integrate without re-design of cap.
• All liners are available in single- and multi-up roll goods as well as in various widths.
NEW
Prevent Leaks and Deformations and Enhance Container Safety
for chemicals and cleaners
Packaging VentsFOR HOUSEHOLD CHEMICALS AND CLEANERS
SERIES: D3, D6, D10
Typical Application IBCs / Drums Drums/Containers Containers/Bottles Cartridges Dispensers/Bottles Trigger Sprayers/Bottles Specialities
Packaging Size 60 – 1500 liters 5 – 60 liters 1 – 30 liters 1 – 5 liters 0.2 – 2 liters 0.2 – 1 liters 0.2 – 1 liters
Product Series D38 D17 D15 D15 Converse D10 D6 D3
Standard Series
Standard Series
High Airflow Series
Standard Series
Standard Series
Standard Series
Standard Series
Standard Series
High Airflow Series
Standard Series
High Airflow Series
Standard Series
Standard Series
Packaging Content Agrochemicals Hazardous Chemicals
Hazardous Chemicals and Agrochemicals
Agrochemicals Hazardous Chemicals
Agrochemicals Hazardous Chemicals
Institutional Cleaners Household Chemicals and Institutional Cleaners
Household Chemicals and Institutional Cleaners
Applications requiring underpressure-compensation
or vacuum-elimination
Order numbers ...
... for Press-Fit Integration CMF300147 CMF300207 CMF300277 CMF300176 CMF300181 CMF300161 CMF300180 CMF300275 CMF300276 CMF300223 CMF300274 CMF300261 CMF300246
... for Snap-Fit Integration – CMF300278 CMF300279 CMF300197 CMF300206 – – – – – – – –
Product Performance Characteristics
Typical Airflow at dp = 12 mbar 9 l/h 27 l/h 80 l/h 1.2l/h 3.6 l/h 1.0 l/h 2.6 l/h 0.7 l/h 2.6 l/h 0.22 l/h 1.2 l/h 0.42 l/h 0.072 l/h
Water Entry Pressure (WEP) > 0.5 bar > 0.6 bar > 0.3 bar > 0.5 bar > 0.6 bar > 0.5 bar > 0.6 bar > 0.5 bar > 0.6 bar > 0.5 bar > 0.3 bar > 0.3 bar > 0.6 bar
Drop-Test Optimized Yes Yes Yes Yes No No No
Traceability Yes: Individually laser-marked Yes: Individually laser-marked Yes: Individually laser-marked On lot level On lot level On lot level On lot level
Membrane Type SE0 SC5 SG5 SE0 SC5 SE0 SC5 SF0 SC5 SF0 SH0 SH0 SC1
Laminate: membrane | backing material ePTFE | – ePTFE | PE/PP ePTFE | PE/PP ePTFE | – ePTFE | PE/PP ePTFE | – ePTFE | PE/PP ePTFE | – ePTFE | PE/PP ePTFE | – ePTFE | – ePTFE | PET
Vent housing: material HDPE HDPE HDPE HDPE PP PP PP
Vent housing: color Natural Natural White Natural Natural Natural White White Grey
Vent Design and Dimensions
Units are in mm
Dimensions without tolerances follow DIN 16742
for chemicals and cleaners
Packaging VentsFOR HOUSEHOLD CHEMICALS AND CLEANERS
SERIES: D3, D6, D10
Liquid side Liquid side Liquid side
Plug-In Vents
PV_gra�cs_D38_Press-Fit__Scale 1:1
O / 37.50
21.4
0
12.0
0
O / 13.00 0.10
GORETM
Membrane
PV_gra�cs_D38_Snap-Fit__Scale 1:1
O / 37.50
15.2
1
5.80
O / 13.00 0.10GORETM
Membrane
PV_gra�cs_D15__Scale 2:1
O / 13.00 0.10
GORETM
Membrane
7.00
O / 15.10
6.00
PV_gra�cs_D17_Snap-Fit__Scale 1:1
GORETM
Membrane
O / 17.20
14.8
0
5.80
O / 13.00 0.10
PV_gra�cs_D17_Press-Fit__Scale 1:1
GORETM
Membrane
O / 17.20
14.8
0
5.80
O / 13.00 0.10
Snap-Fit Integration:
Sca
le o
f 1:1
Press-Fit Integration:
Sca
le o
f 1:1
Snap-Fit Integration:
Press-Fit Integration:
Sca
le o
f 2:1
Press-Fit Integration:
Typical Application IBCs / Drums Drums/Containers Containers/Bottles Cartridges Dispensers/Bottles Trigger Sprayers/Bottles Specialities
Packaging Size 60 – 1500 liters 5 – 60 liters 1 – 30 liters 1 – 5 liters 0.2 – 2 liters 0.2 – 1 liters 0.2 – 1 liters
Product Series D38 D17 D15 D15 Converse D10 D6 D3
Standard Series
Standard Series
High Airflow Series
Standard Series
Standard Series
Standard Series
Standard Series
Standard Series
High Airflow Series
Standard Series
High Airflow Series
Standard Series
Standard Series
Packaging Content Agrochemicals Hazardous Chemicals
Hazardous Chemicals and Agrochemicals
Agrochemicals Hazardous Chemicals
Agrochemicals Hazardous Chemicals
Institutional Cleaners Household Chemicals and Institutional Cleaners
Household Chemicals and Institutional Cleaners
Applications requiring underpressure-compensation
or vacuum-elimination
Order numbers ...
... for Press-Fit Integration CMF300147 CMF300207 CMF300277 CMF300176 CMF300181 CMF300161 CMF300180 CMF300275 CMF300276 CMF300223 CMF300274 CMF300261 CMF300246
... for Snap-Fit Integration – CMF300278 CMF300279 CMF300197 CMF300206 – – – – – – – –
Product Performance Characteristics
Typical Airflow at dp = 12 mbar 9 l/h 27 l/h 80 l/h 1.2l/h 3.6 l/h 1.0 l/h 2.6 l/h 0.7 l/h 2.6 l/h 0.22 l/h 1.2 l/h 0.42 l/h 0.072 l/h
Water Entry Pressure (WEP) > 0.5 bar > 0.6 bar > 0.3 bar > 0.5 bar > 0.6 bar > 0.5 bar > 0.6 bar > 0.5 bar > 0.6 bar > 0.5 bar > 0.3 bar > 0.3 bar > 0.6 bar
Drop-Test Optimized Yes Yes Yes Yes No No No
Traceability Yes: Individually laser-marked Yes: Individually laser-marked Yes: Individually laser-marked On lot level On lot level On lot level On lot level
Membrane Type SE0 SC5 SG5 SE0 SC5 SE0 SC5 SF0 SC5 SF0 SH0 SH0 SC1
Laminate: membrane | backing material ePTFE | – ePTFE | PE/PP ePTFE | PE/PP ePTFE | – ePTFE | PE/PP ePTFE | – ePTFE | PE/PP ePTFE | – ePTFE | PE/PP ePTFE | – ePTFE | – ePTFE | PET
Vent housing: material HDPE HDPE HDPE HDPE PP PP PP
Vent housing: color Natural Natural White Natural Natural Natural White White Grey
Vent Design and Dimensions
Units are in mm
Dimensions without tolerances follow DIN 16742
Liquid side Liquid side Liquid side Liquid side
PV_gra�cs_D15_Converse__Scale 2:1
GORETM
Membrane
O / 13.00 0.10
7.00
O / 15.10
6.00
PV_graphics_D10__Scale 2:1
GORETM
Membrane
7.00
4.50
O / 9.90
O / 8.53 4.04
PV_graphics_D6__Scale 4:1
O / 5.00 0.05
GORETM
Membrane
6.50
3.00 25
°
O / 6.20
PV_graphics_D3__Scale 4:1
GORETM
Membrane
1.80
3.30
O / 2.50 0.03
O / 3.10
Sca
le o
f 2:1
Press-Fit Integration:
Sca
le o
f 2:1
Press-Fit Integration:
Sca
le o
f 4:1
Press-Fit Integration:
Sca
le o
f 4:1
Press-Fit Integration:
In-line airflow test (Not applicable to D10, D6 and D3)
100 % of the vents are airflow- inspected during production. This ensures that every part meets the specified airflow requirements.
In-line camera test (Not applicable to D6)
100 % optical testing ensures that the membrane is integrated properly and is free of defects.
Water entry pressure test
WEP testing allows more control of the membrane integration process and also verifies the membrane’s water entry pressure resistance.
Drop Test (Not applicable to D10, D6 and D3)
Compliant with European ADR standard 6.1
Do not wash or re-use. For single use only.
Tracking
Each D38, D17 and D15 vent is laser- marked with an individual tracking code. This enables Gore to reference the actual production data at any time.
Quality Assurance for Plug-In Vents
Typical Application Bottles Bottles
Packaging Content Hazardous Chemicals, Institutional Cleaners and
Liquid Fertilizer
Household Chemicals and Agrochemicals
Agrochemicals
Product Family Foam Liner Pulp Induction Liner
Product Series High Roll-Off Series Standard Series Low Diffusion Series Standard Series
Order Numbers CM700363G CM700323G CM6B CM6C
Product Performance Characteristics
Typical Airflow at dp = 12 mbar 0.4 l/h/cm2 0.4 l/h/cm2 0.03 l/h 0.04 l/h
Water Entry Pressure (WEP) > 2.7 bar > 1.4 bar > 0.5 bar > 0.5 bar
Drop-Test Optimized* Yes No No
Traceability On lot level On lot level
Membrane | Liner Construction ePTFE | PE foam ePTFE | PE + aluminium + PET + wax + pulp
Thickness [mm] 1.1 1.0
Venting Hole Diameter [mm] the whole liner surface is breathable 0.6 2.0
Venting Method cap thread venting (venting through hole in cap also possible)
cap thread venting (venting through hole in cap also possible)
New
PV-1
09-D
SH
-EN
-MA
R17
International ContactsAustralia +61 2 9473 6800Benelux +49 89 4612 2211China +86 21 5172 8299France +33 1 5695 6565Germany +49 89 4612 2211India +91 22 6768 7000Italy +39 045 6209 240Japan +81 3 6746 2570Korea +82 2 393 3411Mexico +52 81 8288 1281
Scandinavia +46 31 706 7800Singapore +65 6733 2882South Africa +39 045 6209 240South America/ Brazil +55 11 5502 7800Spain +34 93 480 6900Taiwan +886 2 2173 7799 Turkey +90 216 3935749United Kingdom +44 1506 460123USA +1 410 506 7812
W. L. Gore & Associates GmbH Hermann-Oberth-Str. 26 • 85640 Putzbrunn • Germany Tel.: +49 89 4612 2211 • Fax: +49 89 4612 2302E-mail: [email protected]
gore.com/packvents
FOR INDUSTRIAL USE ONLY. Not for use in food, drug, cosmetic or medical device manufacturing, processing, or packaging operations.All technical information and advice given here are based on Gore’s previous experiences and/or test results. Gore gives this information to the best of its knowledge, but assumes no legal responsibility. Customers are asked to check the suitability and usability in the specific application, since the perform- ance of the product can only be judged when all necessary operating data are available. The above information is subject to change and is not to be used for specification purposes. Gore’s terms and conditions of sale apply to the sale of the products by Gore.
GORE and designs are trademarks of W. L. Gore & Associates.© 2017 W. L. Gore & Associates GmbH
* Drop Test: compliant with European ADR standard 6.1
All liners are available in single- and multi-up roll goods as well as in various widths. Cut parts can also be offered.
Liners
for chemicals and cleaners
Packaging VentsFOR HOUSEHOLD CHEMICALS AND CLEANERS
SERIES: D3, D6, D10
