Pack 17 - US website
Transcript of Pack 17 - US website
PackPack
1717
STAGE PAGE81 Ceiling lining 275
82 The headlights 278
83 The fuse box 281
84 Left rear inner body panel 284
85 Right rear inner body panel 287
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ. Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.All rights reserved © 2020
Warning: Not suitable for children under the age of 14. This product is not a toy and is not designed or intended for use in play. Items may vary from those shown.
275
Your parts: 81A. Ceiling lining 81B. Interior light 81C. Caravan reflector holder 81D. Caravan reflector 81E. Stickers NP. 2 x 2.5 x 5mm screws CP. 1.7 x 4mm screws EM. 2 x 3mm screws
Stage 81: Ceiling lining
276
2 Turn the par ts over and sec ure with four NP screws.1 Connec t the cei l ing l in ing (81A) to the roof inner (78A), inser t ing the posts into the corresponding holes.
4 Run the cable a long the groove in the roof inner.3 Prepare the inter ior l ight (81B) and gently bend the wire just under the LED bulb to a 90– degree angle.
6 Remove the crossbars f rom the bottom of the body.5 S ec ure the cable with three st ickers (81E) , as shown.
277
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
7 Place the roof inner ins ide the body, a l igning the holes of both. When in posit ion, sec ure with four EM screws.
278
Your parts: 82A. Headlights 82B. Tabs 82C. Caravan reflector holder 82D. Caravan reflector AM. 1.7 x 3mm screws CP. 1.7 x 4mm screws
Stage 82: The headlights
279
2 Posit ion the cable as shown and place the t wo tabs over i t, a l igning them with the holes in the panel, as shown.1 Inser t the headl ights (82A) into the housings in the f ront panel.
3 S ec ure with t wo AM screws. 4 Now combine the caravan ref lec tors (81D and 82D) with the holders (81C and 82C )
280
6 S ec ure the holders f rom ins ide the caravan with t wo CP screws.5 Inser t the backs of the holders into the t wo indicated holes in the f ront of the caravan
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
281
Your parts: 83A. Fuse box 83B. Boot lid lock 83C. Caravan front lights AP. 1.7 x 3mm screws BM. 2 x 4mm screws IP. 2 x 4mm screws
Stage 83: The fuse box
282
2 S ec ure f rom underneath with t wo IP screws.1 P lace the fuse box (83A) on the lef t s ide of the body. Inser t the pin into the centre hole.
3 Place the boot l id lock (83B) into the indicated posit ion on the body. Al ign the holes of both par ts. 4 S ec ure the lock with t wo BM screws.
283
6 S ec ure the l ights f rom the ins ide with t wo AP screws.5 Instal l the caravan f ront l ights (83C ) in the indicated posit ions in the f ront wal l.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
284
Your parts: 84A. Left rear inner body panel 84B. Caravan front light lenses CM. 2.3 x 4mm screws
Stage 84: Left rear inner body panel
285
2 Make sure that the l ight ing cable doesn’t get p inched bet ween the t wo par ts. Then sec ure the panel with a CM screw.1 Turn the body over and al ign the lef t rear inner body panel (84A)
with the ins ide of the body. Match the screw holes to each other.
3 Mount one of the caravan f ront l ight lenses (84B) into one of the l ights. 4 Fix the second lens into place.
286
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
287
Your parts: 85A. Right rear inner body panel 85B. Front inner caravan wall CM. 2.3 x 4mm screws IP. 2 x 4mm screws
Stage 85: Right rear inner body panel
288
2 S ec ure the panel with a CM screw.1 Instal l the r ight rear inner body panel (85A) on the ins ide of the body, in the same way as the lef t panel.
3 Now mount the f ront inner caravan wal l (85B) on the ins ide of the outer wal l, a l igning the holes of both par ts. 4 Fix the f ront wal l in posit ion with four IP screws.
289
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.