P4M800-M7v31 motherboad

Preface

PrefaceCopyright

This publication, including all photographs, illustrations and software, is protected underinternational copyright laws, with all rights reserved. Neither this manual, nor any of thematerial contained herein, may be reproduced without written consent of the author.

Version 3.1

DisclaimerThe information in this document is subject to change without notice. The manufacturermakes no representations or warranties with respect to the contents hereof and specificallydisclaims any implied warranties of merchantability or fitness for any particular purpose.The manufacturer reserves the right to revise this publication and to make changes fromtime to time in the content hereof without obligation of the manufacturer to notify anyperson of such revision or changes.

Trademark RecognitionMicrosoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Cor-poration.

Other product names used in this manual are the properties of their respective owners andare acknowledged.

Federal Communications Commission (FCC)This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmful interference in a residential installation. This equipmentgenerates, uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna• Increase the separation between the equipment and the receiver• Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with thisequipment to ensure compliance with the pertinent RF emission limits governing thisdevice. Changes or modifications not expressly approved by the system’s manufacturercould void the user’s authority to operate the equipment.

ii

Preface

Declaration of ConformityThis device complies with part 15 of the FCC rules. Operation is subject to the followingconditions:

• This device may not cause harmful interference, and• This device must accept any interference received, including interference

that may cause undesired operation

Canadian Department of CommunicationsThis class B digital apparatus meets all requirements of the Canadian Interference-causingEquipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur lematériel brouilieur du Canada.

About the ManualThe manual consists of the following:

Chapter 1

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

Describes features of the motherboard.

Go to page 1

Describes installation of motherboardcomponents.

Go to page 7

Provides information on using the BIOSSetup Utility.

Go to page 25

Describes the motherboard software

Go to page 37

iii

TTTTTABLE OF CONTENTSABLE OF CONTENTSABLE OF CONTENTSABLE OF CONTENTSABLE OF CONTENTS

Preface i

Chapter 1 1Introducing the Motherboard 1

Introduction.................................................................................................1Feature..........................................................................................................2Motherboard Components........................................................................4

Chapter 2 7 7 7 7 7Installing the Motherboard 7

Safety Precautions......................................................................................7Choosing a Computer Case.......................................................................7Installing the Motherboard in a Case......................................................7Checking Jumper Settings.........................................................................8

Setting Jumpers..............................................................................8Checking Jumper Settings..............................................................9Jumper Settings..............................................................................9

Connecting Case Components...............................................................10Front Panel Header.....................................................................11

Installing Hardware...................................................................................13Installing the Processor...............................................................13Installing Memory Modules.........................................................15Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........16Installing a Floppy Diskette Drive...............................................18Installing Add-on Cards..............................................................19Connecting Optional Devices......................................................20

Connecting I/O Devices..........................................................................23

Chapter 3 25 25 25 25 25Using BIOS 25

About the Setup Utility............................................................................25The Standard Configuration........................................................25Entering the Setup Utility..............................................................25Updating the BIOS.......................................................................26

Using BIOS................................................................................................27Standard CMOS Setup.................................................................28Advanced Setup............................................................................29Features Setup.............................................................................31

iv

Power Management Setup...........................................................32PCI / Plug and Play Setup Page...................................................33BIOS Security Features Setup Page.............................................34CPU PnP Setup Page...................................................................34Hardware Monitor Page.............................................................35Load Optimal Defaults................................................................36Set Changes and Exit...................................................................36Discard Changes and Exit...........................................................36

Chapter 4 37 37 37 37 37Using the Motherboard Software 37

About the Software CD-ROM................................................................37Auto-installing under Windows 98/ME/2000/XP................................37

Running Setup..............................................................................39Manual Installation..................................................................................40Utility Software Reference.......................................................................40

Multi-Language Translation

1


Chapter 1Introducing the Motherboard

IntroductionThis motherboard has a LGA775 socket for latest Intel Pentium 4/Pentium D/Celeron Dprocessors with Hyper-Threading Technology and Front-Side Bus (FSB) speeds up to 800MHz. Hyper-Threading Technology, designed to take advantage of the multitasking fea-tures in Windows XP, gives you the power to do more things at once.

It integrates the VIA P4M800 Northbridge and VT8237 Southbridge that supports the SerialATA interface for high-performance and maiinstream desktop PCs; the built-in USB 2.0providing higher bandwidth, implementing Universal Serial Bus Specification Revision 2.0and is compliant with UHCI 1.1 and EHCI 0.95. It supports AC’ 97 Audio Codec andprovides Ultra DMA 133/100/66 function. It has one 8X AGP, one CNR and three 32-bitPCI slots. There is a full set of I/O ports including two PS/2 ports for mouse and keyboard,one serial port, one parallel port, one LAN port(optional), one VGA port, three audio jacksfor Line-in, Line-out and Microphone, four back-panel USB2.0 ports and onboard USBheaders providing extra ports by connecting the Extended USB Module to the motherboard.

It is a Micro ATX motherboard and has power connectors for an ATX power supply.

2


• High Performance UMA North Bridge: Integrated Pentium 4North Bridge with 800 MHz FSB support and UniChromePro 3D / 2D Graphics & Video Controllers in a single chip

• Supports Intel 800/533 MHz FSB Pentium 4 and Pentium Mprocessors and Hyper Threading Technology

• AGP v3.0 compliant 8x / 4x transfer modes with Fast Writesupport

• Supports DDR400 / 333 / 266 memory types with 2.5VSSTL-2 DRAM interface

• Supports 66 MHz, 4X and 8X transfer modes, V-Link inter-face with 533 MB/sec total bandwidth

• ACPI 2.0 and PCI Bus Power Management 1.1 compliant• Graphics engine clocks up to 133 MHz decoupled from

memory clock

VIA P4M800(NB)

• PCI to system memory data streaming up to 132Mbyte/sec(data sent to north bridge via high speed Ultra V-Link inter-face)

• PCI-2.2 compliant, 32-bit 3.3V PCI interface with 5V tolerantinputs

• Support three PCI slots of arbitration and decoding for allintegrated functions and LPC bus.

• Dual Channel Serial ATA/RAID Controller—Complies withSerial ATA Specification Revision 1.0

VT8237 (SB)

Memory• Two 184-pin 2.5V DIMM sockets for DDR SDRAM memory modules• Supports DDR400/333/266 memory bus• Maximum installed memory is 2GB

Expansion Slots• Three 32-bit PCI slots• One 8X AGP slot• One CNR slot

Feature

• Accommodates Intel Pentium 4/ Pentium D/Celeron D processors• Supports a system bus (FSB) of 800MHz• Supports “Hyper-Threading” technology CPU

“Hyper-Threading” technology enables the operating system into thinking it’s hookedup to two processors, allowing two threads to be run in parallel, both on separate“logical” processors within the same physical processor.

This motherboard uses a LGA775 type of Pentium 4/ Pentium D/ Celeron D seriesprocessors:

Processor

ChipsetThe VIA P4M800 Northbridge (NB) and VT8237 Southbridge (SB) chipset are based onan innovative and scalable architecture with proven reliability and performance.

3


Onboard IDE Channels• Supports PIO (Programmable Input/Output) and DMA (Direct Memory Ac-

cess) modes• Supports IDE Ultra DMA bus mastering with transfer rates of 133/100/66

MB/secSerial ATA• Two Serial ATA Connectors• Transfer rate exceeding best ATA (~150 MB/s) with scalability to higher

rates• Low pin count for both host and devicesAC’97 Audio Codec• Compliant with AC’97(Rev 2.3) CODEC.• Front-Out,Surround-Out,MIC-In and Line-In Jack Sensing• Three analog line-level stereo inputs with 5-bit volume control:

LINE_IN,CD,AUX• Two analog line-level mono input• 48-pins LQFP.• Built-in earphone buffer and internal PLL.Onboard I/O Ports• Two PS/2 ports for mouse and keyboard• One serial port• One parallel port• One VGA port• One LAN port (optional)• Four back-panel USB2.0 ports• Audio jacks for microphone, line-in and line-outFast Ethernet LAN (optional)• Single Chip 100Base-TX / 10Base-T Physical Layer Solution• Dual Speed – 100/10 Mbps• Half and Full Duplex• MII Interface to Ethernet Controller• MII Interface to Configuration & Status• Auto Power Saving Mode.• Auto Negotiation: 10 / 100, Full / Half Duplex• Meet All Applicable IEEE 802.3, 10Base-T and 100Base-Tx Standards.• On Chip Wave Shaping – No External Filters Required.• Adaptive Equalizer.• Baseline wander Correction.• LED OutputsBIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many system featuresincluding the following:

• Power management• Wake-up alarms• CPU parameters and memory timing• CPU and memory timing

The firmware can also be used to set parameters for different processor clock speeds.

4


Motherboard Components

Some hardware specifications and software items are subject to changewith out prior notice.

5


Table of Motherboard Components

ITEM LABEL COMPONENTS

1 CPU Socket LGA775 Socket for Intel Pentium 4/Pentium D/Celeron D processors

2 CPU_FAN CPU fan connector3 DDR1/2 Two 184-pin DDR SDRAM Sockets

4 IDE 1 Primary IDE channel5 IDE 2 Secondary IDE channel6 SATA1/2 Serial ATA connectors7 CLR_CMOS1 Clear CMOS jumper8 PANEL1 Front panel switches and LED header

9 SPK1 Speaker header10 SYS_FAN1 System fan connector11 FDD1 Floppy disk drive connector12 F_USB1/2 Front panel USB headers

13 CNR1 Communications Networking Riser slot14 PCI1 ~ PCI3 Three 32-bit PCI slots15 IR1 Infrared header16 CD_IN1 Analog Audio Input header17 AGP1 AGP slot18 AUDIO1 Front Panel Audio header19 PWR1 Standard 20-pin ATX power connector20 PWR2 Standard 4-Pin ATX Power connector

This concludes Chapter 1. The next chapter explains how to install the motherboard.

*Stands for optional components

6


Memo

7


Chapter 2Installing the Motherboard

Safety Precautions• Follow these safety precautions when installing the motherboard• Wear a grounding strap attached to a grounded device to avoid damage from

static electricity• Discharge static electricity by touching the metal case of a safely grounded

object before working on the motherboard• Leave components in the static-proof bags they came in• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer CaseThere are many types of computer cases on the market. The motherboard complies withthe specifications for the Micro ATX system case. First, some features on the motherboardare implemented by cabling connectors on the motherboard to indicators and switches onthe system case. Make sure that your case supports all the features required. Secondly, itsupports one floppy diskette drive and one enhanced IDE drive. Make sure that your casehas sufficient power and space for all drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/Otemplate in the case matches the I/O ports installed on the rear edge of the motherboard.

This motherboard carries a Micro ATX form factor of 244 x 220 mm. Choose a case thataccommodates this form factor.

Installing the Motherboard in a CaseRefer to the following illustration and instructions for installing the motherboard in a case.

Most system cases have mounting brackets installed in the case, which correspond the holesin the motherboard. Place the motherboard over the mounting brackets and secure themotherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion slotson your motherboard.

8


Checking Jumper SettingsThis section explains how to set jumpers for correct configuration of the motherboard.

Setting JumpersUse the motherboard jumpers to set system configuration options. Jumpers with more thanone pin are numbered. When setting the jumpers, ensure that the jumper caps are placed onthe correct pins.

The illustrations show a 2-pin jumper. Whenthe jumper cap is placed on both pins, thejumper is SHORT. If you remove the jumpercap, or place the jumper cap on just one pin,the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins1 and 2 are SHORT

SHORT OPEN

Do not over-tighten the screws as this can stress the motherboard.

9


Checking Jumper SettingsThe following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

Jumper Settings

Jumper Type Description Setting (default)

CLR_CMOS1 3-pin Clear CMOS 1-2: NORMAL

2-3: CLEAR CMOSBefore clearing theCMOS, make sure toturn off the system. CLR_CMOS1

1

10


Connecting Case ComponentsAfter you have installed the motherboard into a case, you can begin connecting themotherboard components. Refer to the following:

1 Connect the CPU cooling fan cable to CPU_FAN.2 Connect the case cooling fan connector to SYS_FAN1.3 Connect the case switches and indicator LEDs to the PANEL1.4 Connect the standard power supply connector to PWR1.5 Connect the auxiliary case power supply connector to PWR2.6 Connect the case speaker cable to SPK1.

CPU_FAN: FAN Power Connector

1 GND System Ground2 +12V Power +12V3 Sense Sensor4 Control FAN Speed control

Pin Signal Name Function

Users please note that the fan connector supports the CPU cooling fan of1.1A~2.2A (26.4W max) at +12V.

SYS_FAN1: FAN Power Connector

Pin Signal Name Function1 GND System Ground2 +12V Power +12V3 Sense Sensor

11


PWR2: ATX 12V Power Connector

Pin Signal Name

4 +12V

3 +12V

2 GND

1 GND

PWR1: ATX 20-pin Power ConnectorPin Signal Name Pin Signal Name1 +3.3V 11 +3.3V

2 +3.3V 12 -12V

3 Ground 13 GND

4 +5V 14 PS_ON

5 Ground 15 GND

6 +5V 16 GND

7 Ground 17 GND

8 PWRGD 18 -5V

9 +5VSB 19 +5V

10 +12V 20 +5V

Front Panel HeaderThe front panel header (PANEL1) provides a standard set of switch and LED headerscommonly found on ATX or Micro ATX cases. Refer to the table below for information:

Pin Signal Function Pin Signal Function1 HDD_LED_P Hard disk LED+ 2 FP PWR/SLP *MSG LED+

3 HDD_LED_N Hard disk LED-

5 RST_SW_N Reset Switch-

7 RST_SW_P Reset Switch+

9 RSVD Reserved

4 FP PWR/SLP *MSG LED-

6 PWR_SW_P Power Switch+

8 PWR_SW_N Power Switch-

10 Key No pin

* MSG LED (dual color or single color)

12


Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that datais being read from or written to the hard drive. For the LED to function properly, an IDEdrive should be connected to the onboard IDE interface. The LED will also show activityfor devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides poweron/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentary-contactswitch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 msto signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses beforethe power supply recognizes another on/off signal.

13


Installing HardwareInstalling the Processor

Caution: When installing a CPU heatsink and cooling fan make sure thatyou DO NOT scratch the motherboard or any of the surface-mountresistors with the clip of the cooling fan. If the clip of the cooling fanscrapes across the motherboard, you may cause serious damage to themotherboard or its components.

On most motherboards, there are small surface-mount resistors near theprocessor socket, which may be damaged if the cooling fan is carelesslyinstalled.

Avoid using cooling fans with sharp edges on the fan casing and theclips.Also, install the cooling fan in a well-lit work area so that you canclearly see the motherboard and processor socket.

Before installing the ProcessorThis motherboard automatically determines the CPU clock frequency and system busfrequency for the processor. You may be able to change these settings by making changesto jumpers on the motherboard, or changing the settings in the system Setup Utility. Westrongly recommend that you do not over-clock processors or other components to runfaster than their rated speed.

Warning: Over-clocking components can adversely affect the reliability ofthe system and introduce errors into your system. Over-clocking canpermanently damage the motherboard by generating excess heat incomponents that are run beyond the rated limits.

This motherboard has a LGA775 socket. When choosing a processor, consider the perfor-mance requirements of the system. Performance is based on the processor design, the clockspeed and system bus frequency of the processor, and the quantity of internal cache memoryand external cache memory.

14


A. Unload the cap· Use thumb & forefinger to hold the lifting tab of the cap.· Lift the cap up and remove the cap completely from the socket.

B. Open the load plate· Use thumb & forefinger to hold the hook of the lever, pushing down and pulling aside unlock it.· Lift up the lever.· Use thumb to open the load plate. Be careful not to touch the contacts.

C. Install the CPU on the socket· Orientate CPU package to the socket. Make sure you match triangle marker to pin 1 location.

D. Close the load plate· Slightly push down the load plate onto the tongue side, and hook the lever.· CPU is locked completely.

E. Apply thermal grease on top of the CPU.

F. Fasten the cooling fan supporting base onto the CPU socket on the motherboard.

G. Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan user’s manual for more detail installation procedure.

CPU Installation ProcedureThe following illustration shows CPU installation components.

1.To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.2.The fan connector supports the CPU cooling fan of 1.1A~2.2A (26.4W max.) at +12V.3.DO NOT remove the CPU cap from the socket before installing a CPU.

15


Installation ProcedureRefer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR SDRAM .2 Push the latches on each side of the DIMM slot down.3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only beinstalled correctly.

4 Check that the cutouts on the DIMM module edge connector match the notchesin the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it seatscorrectly. The slot latches are levered upwards and latch on to the edges ofthe DIMM.

6 Install any remaining DIMM modules.

Installing Memory ModulesThis motherboard accommodates two 184-pin 2.5V DIMM sockets (Dual Inline MemoryModule) for unbuffered DDR400/333/266 (Double Data Rate SDRAM), and maximum 2.0GB installed memory.

DDR SDRAM is a type of SDRAM that supports data transfers on both edges of each clockcycle (the rising and falling edges), effectively doubling the memory chip’s data throughput.DDR DIMMs can synchronously work with 400/333/266 MHz memory and provide 3.2GB/s, 2.7 GB/s, 2.1 GB/s and 1.6 GB/s data transfer rate.

16


Table: DDR (memory module) QVL (Qualified Vendor List)The following DDR400 memory modules have been tested and qualified for use with thismotherboard.

Size Vendor Module Name

SAMSUNG K4H560838D-TCC4

TwinMOS TMD7608F8E50D

KingMax KDL684T4AA-50

KingMax KDL388P4EA-50A

Winbond W942508BH-5

A-DATA ADD8608A8A-5B

A-DATA ADD8608A8A-4.5B

Kingston 9905192-012.A01

Hynix HY5DU5656822BT-D43

Hynix HY5DU56822BT-D43

GEIL GE08L3264D1WL5NKT3H71

GEIL G208L364D1TG5NKT3C

Apacer AM3A568ACT-5A

Ramaxel MT-46V32M8 TG-5BC

SAMSUNG K4H560838D-TCC4

SAMSUNG K4H560838E-TCCC

Infineon HYB25D256800BT-5

Elixir N2DS25680BT-5T

Kingston D3208DL1T-5

PSC A2S56D30BTP

Transcend V58C2256804SAT5B

ValueSelect VS32MB-5 2B0402

CORSAIR CMX512-3200C2PT

UNIFOSA USI 64M8B8-WB200-0431

GEIL GE1GB3200BDC

G.SKILL F1-3200PHU2-1 GVZX

AENEON AED93T500

AENEON AED83T500

A-DATA VIESTA

CORSAIR CMX1024-3200PT1GB

512MB

256MB

17


Installing a Hard Dish Drive/CD-ROM/SATA Hard DriveThis section describes how to install IDE devices such as a hard disk drive and a CD-ROMdrive.

About IDE DevicesYour motherboard has two IDE channel interfaces (IDE1 & IDE2). Two IDE ribbon cablessupporting four IDE devices is bundled with the motherboard.

IDE1: Primary IDE ConnectorThe first hard drive should always be connected to IDE1.

IDE2: Secondary IDE ConnectorThe second drive on this controller must be set to slave mode. The configuration is thesame as IDE1.

IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE.Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure thatone device is set to MASTER and the other device is set to SLAVE. The documentation ofyour IDE device explains how to do this.

You must orient the cable connector so that the pin1 (color) edge of thecable correspoinds to the pin 1 of the I/O port connector.

18


Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard.2 Attach the other cable end to the SATA hard drive.3 Attach the SATA power cable to the SATA hard drive and connect the other

end to the power supply.

SATA cable (optional) SATA power cable (optional)

This motherboard does not support the “Hot-Plug” function.

About SATA ConnectorsYour motherboard features two SATA connectors supporting a total of two drives. SATA , orSerial ATA (Advanced Technology Attachment) is the standard interface for the IDE harddrives which are currently used in most PCs. These connectors are well designed and willonly fit in one orientation. Locate the SATA connectors on the motherboard and follow theillustration below to install the SATA hard drives.

Installing Serial ATA Hard DrivesTo install the Serial ATA (SATA) hard drives, use the SATA cable that supports the SerialATA protocol. This SATA cable comes with an SATA power cable. You can connect eitherend of the SATA cable to the SATA hard drive or the connector on the motherboard.

19


Installing a Floppy Diskette DriveThe motherboard has a floppy diskette drive (FDD1) interface and ships with a diskettedrive ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable hasone type of connector for a 5.25-inch drive and another type of connector for a 3.5-inchdrive.

You must orient the cable connector so that the pin 1 (color) edge of thecable corresponds to the pin 1 of the I/O port connector.

FDD1: Floppy Disk ConnectorThis connector supports the provided floppy drive ribbon cable. After connecting the singleend to the onboard floppy connector, connect the remaining plugs on the other end to thefloppy drives correspondingly.

20


Installing Add-on CardsThe slots on this motherboard are designed to hold expansion cards and connect them to thesystem bus. Expansion slots are a means of adding or enhancing the motherboard’s featuresand capabilities. With these efficient facilities, you can increase the motherboard’s capabili-ties by adding hardware that performs tasks that are not part of the basic system.

Before installing an add-on card, check the documentation for the cardcarefully. If the card is not Plug and Play, you may have to manuallyconfigure the card before installation.

Follow these instructions to install an add-on card:1 Remove a blanking plate from the system case corresponding to the slot you

are going to use.2 Install the edge connector of the add-on card into the expansion slot. Ensure

that the edge connector is correctly seated in the slot.

This motherboard is equipped with three standard PCI slots. You can installthe 32-bit PCI interface expansion cards in the slots.

PCI Slots

CNR Slot You can install the CNR (Communications and Networking Riser) cards inthis slot, including LAN, Modem, and Audio functions.

8X AGPSlot

You can install a graphics adapter that supports the 8X AGP specificationand has a 8X AGP edge connector in the AGP slot.

21


3 Secure the metal bracket of the card to the system case with a screw.

Connecting Optional DevicesRefer to the following for information on connecting the motherboard’s optional devices:

For some add-on cards, for example graphics adapters and networkadapters, you have to install drivers and software before you can beginusing the add-on card.

22


AUDIO1: Front Panel Audio headerThis header allows the user to install auxiliary front-oriented microphone and line-out portsfor easier access.

F_USB1/F_USB2: Front Panel USB headersThe motherboard has four USB ports installed on the rear edge I/O port array. Additionally,some computer cases have USB ports at the front of the case. If you have this kind of case,use auxiliary USB connector to connect the front-mounted ports to the motherboard.

CD_IN1: Analog Audio Input header

1 CD IN L

2 GND

3 GND

4 CD IN R

Pin Signal Name

1 VERG_FP_USBPWR0

2 VERG_FP_USBPWR0

3 USB_FP_P0 (-)

4 USB_FP_P1 (-)

5 USB_FP_P0 (+)

6 USB_FP_P1 (+)

7 GROUND

8 GROUND

9 KEY

10 USB_FP_OC0

Please make sure that the USB cable has the same pin assignment asindicated above. A different pin assignment may cause damage orsystem hand-up.

1 AUD_MIC

2 AUD_GND

3 AUD_MIC_BIAS

4 AUD_VCC

5 AUD_FPOUT_R

6 AUD_RET_R

7 HP_ON

8 KEY

9 AUD_FPOUT_L

10 AUD_RET_L

Pin Signal Name

Pin Signal Name

23


SATA1/2: Serial ATA connectorsThese connectors are use to support the new Serial ATA devices for the highest date transferrates (150 MB/s), simpler disk drive cabling and easier PC assembly. It eliminates limitationsof the current Parallel ATA interface. But maintains register compatibility and softwarecompatibility with Parallel ATA.

Pin Signal Name Function1 GROUND 2 TX+

3 TX- 4 GROUND

5 RX- 6 RX+

7 GROUND - -

Pin Signal Name Pin Signal Name

IR1: Infrared headerThis motherboard supports an Infrared (IRDA) data port. Infrared ports allow the wirelessexchange of information between your computer and similarly equippped devices such asprinters, laptops, Personal Digital Assistants (PDAs), and other computers.

1 NC

2 KEY

3 +5V

4 GND

Pin Signal Name

5 IRTX

6 IRRX

24


Connecting I/O DevicesThe backplane of the motherboard has the following I/O ports:

This concludes Chapter 2. The next chapter covers the BIOS.

PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.

PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.

Parallel Port (LPT1) Use LPT1 to connect printers or other parallel communicationsdevices.

Serial Port Use the COM port to connect serial devices such as mice or(COM1) fax/modems. COM1 is identified by the system as COM1/3.

VGA Port Connect your monitor to the VGA port.

LAN Port (optional) Connect an RJ-45 jack to the LAN port to connect your computerto the Network.

USB Ports Use the USB ports to connect USB devices.

Audio Ports Use the three audio ports to connect audio devices. The first jackis for stereo line-in signal. The second jack is for stereo line-outsignal. The third jack is for microphone.

25

Using BIOS

Chapter 3

Using BIOS

About the Setup UtilityThe computer uses the latest American Megatrends BIOS with support for Windows Plugand Play. The CMOS chip on the motherboard contains the ROM setup instructions forconfiguring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configura-tion status and provides you with options to set system parameters. The parameters arestored in battery-backed-up CMOS RAM that saves this information when the power isturned off. When the system is turned back on, the system is configured with the values youstored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals• Video display type and display options• Password protection from unauthorized use• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using theSetup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard ConfigurationA standard configuration has already been set in the Setup Utility. However, we recommendthat you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:• when changing the system configuration• when a configuration error is detected and you are prompted to make changes

to the Setup Utility• when trying to resolve IRQ conflicts• when making changes to the Power Management configuration• when changing the password or making other changes to the Security Setup

Entering the Setup UtilityWhen you power on the system, BIOS enters the Power-On Self Test (POST) routines.POST is a series of built-in diagnostics performed by the BIOS. After the POST routines arecompleted, the following message appears:

26

Using BIOS

Press DEL to enter SETUPPress the delete key to access the BIOS Setup Utility:

Updating the BIOSYou can download and install updated BIOS for this motherboard from the manufacturer’sWeb site. New BIOS provides support for new peripherals, improvements in performance,or fixes for known bugs. Install new BIOS as follows:

1 If your motherboard has a BIOS protection jumper, change the setting to allowBIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in AdvancedBIOS features, disable it. (Firmware Write Protect prevents BIOS from beingoverwritten.

3 Create a bootable system disk. (Refer to Windows online help for informationon creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s Website. Copy these files to the system diskette you created in Step 3.

5 Turn off your computer and insert the system diskette in your computer’sdiskette drive. (You might need to run the Setup Utility and change the bootpriority items on the Boot Configuration Features, to force your computer toboot from the floppy diskette drive first.)

BIOS Navigation KeysThe BIOS navigation keys are listed below:

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc

Standards COMOS setup for changing time, date, hard disk type, etc.V02.54 (C) 1985-2003, American Megatrends, Inc.

: Move Enter: Select +/-/: Value F10: Save Esc: Exit F1: General Help F9: Optimized Settings

Standard CMOS SetupAdvanced SetupFeatures SetupPower Management SetupPCI / Plug and Play SetupBIOS Security Features

CPU PnP SetupHardware MonitorLoad Optimal DefaultsSave Changes and ExitDiscard Changes and Exit

KEY FUNCTION

ESC Exits the current menu

Scrolls through the items on a menu

+/- Modifies the selected field’s values

F10 Saves the current configuration and exits setup

F1 Displays a screen that describes all key functionsF9 Loads an optimized setting for better performance

ESC Exits the current menu

27

Using BIOS

Using BIOSWhen you start the Setup Utility, the main menu appears. The main menu of the SetupUtility displays a list of the options that are available. A highlight indicates which option iscurrently selected. Use the cursor arrow keys to move the highlight to other options. Whenan option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish toexecute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with a triangle ) lead to submenus that enable you to change thevalues for the option. Use the cursor arrow keys to scroll through the items in the submenu.

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by atriangle .

6 At the A:\ prompt, type the Flash Utility program name and the file name of thenew BIOS, then press <Enter>, example:AMINF340.EXE 0470706.ROM

7 When the installation is complete, remove the floppy diskette from the diskettedrive and restart your computer. If your motherboard has a Flash BIOS jumper,reset the jumper to protect the newly installed BIOS from being overwritten.The computer will restart automatically.

28

Using BIOS

Standard CMOS SetupThis option displays basic information about your system.

Press <Esc> to return to the main menu setting page.

System Time & System DateThese items set up system date and time.

Primary IDE Master/Primary IDE Slave/Secondary IDE Master/Secondary IDESlaveYour computer has two IDE channels and each channel can be installed with one or twodevices (Master and Slave). In addition, this motherboard supports two SATA channels andeach channel allows one SATA device to be installed. Use these items to configure eachdevice on the IDE channel.

Floppy A/BThese items set up size and capacity of the floppy diskette drive(s) installed in the system.

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.Standard CMOS Setup

System Time 00:01:25System Date Fri 10/24/2003

Primary IDE Master Hard DiskPrimary IDE Slave Not DetectedSecondary IDE Master Not DetectedSecondary IDE Slave CD/DVD ROM

Floppy A 1.44 MB 3 1/2”Floppy B Disabled

Help Item

User [Enter], [TAB] or [SHIFT-TAB] toselect a field.Use [+] or [-] to configure system time.

29

Using BIOS

Advanced SetupThis page sets up more advanced information about your system. Handle this page withcaution. Any changes can affect the operation of your computer.

Quick Boot1st Boot Device2nd Boot Device3rd Boot DeviceTry Other Boot DeviceBootup Num-LockBoot To OS/2 > 64 MBAGP Aperture SizeDRAM TimingDRAM CAS# LatencyDRAM Bank InterleaveHyper Threading FunctionAuto Detect DIMM/PCI ClkSpread SpectrumMax CPUID Value LimitExecute Disable BitCPU TM FunctionC1E SupportIntel (R) SpeedStep (tm) tech.Venderpool TechnologyDRAM Driving

EnabledPM-IC35L040AVVN07SS-Pioneer DVD-R01st Floppy DriveYesOnNo64 MBManualBy SPD4-wayEnsabledEnabledDisabledDisabledEnabledTM1DisabledDisabledEnabledNormal

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.Advanced Setup

Help Item

Allows BIOS to skip certaintests while booting. This willdecrease the time needed toboot the system.

Quick BootIf you enable this item, the system starts up more quickly be elimination some of the poweron test routines.

1st Boot Device/2nd Boot Device/3rd Boot DeviceUse these items to determine the device order the computer uses to look for an operatingsystem to load at start-up time.

Try Other Boot DeviceIf you enable this item, the system will also search for other boot devices if it fails to findan operating system from the first two locations.

BootUp Num-LockThis item determines if the Num Lock key is active or inactive at system start-up time.

Boot To OS/2> 64MBEnable this item if you are booting the OS/2 operating system and you have more than64MB of system memory installed.

AGP Aperture SizeThis item defines the size of aperture if you use a graphic adapter.

DRAM TimingThis item allows you to enable or disable the DRAM timing defined by the Serial PresenceDetect electrical.

DRAM CAS# LatencyThis item determines the operation of SDRAM memory CAS (column address strobe). It isrecommended that you leave this item at the default value. The 2T setting requires fastermemory that specifically supports this mode.

30

Using BIOS


DRAM Bank InterleaveEnable this item to increase DRAM memory speed. When enabled, separate memory banksare set for odd and even addresses and the next byte of memory can be accessed while thecurrent byte is being refreshed.

Hyper Threading FunctionYou can set “Disabled” or “Enabled” to control HT CPU support in O.S. Set“Enabled” to test HT CPU function.Auto detect DIMM/PCI ClockWhen this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.

Spread SpectrumIf you enable spread spectrum, it can significantly reduce the EMI (Electro-MagneticInterference) generated by the system.

Max CPUID Value LimitWhen this item is enabled, you can use Prescott CPU and LGA-775 CPU and there will bea normal NT4.0 installation; otherwise, the automatically restarting will occur while install-ing.

Execute Disable BitIt allows the processor to classify areas in memory by where application code can executeand where it cannot. When a malicious worm attempts to insert code in the buffer, theprocessor disables code execution, preventing damage or worm propagation. Replacingolder computers with Execute Disable Bit-enabled systems can halt worm attacks, reducingthe need for virus related repairs.

CPU TM FunctionFor some specific brands of CPU, you can use this item to control the CPU frequency andvoltage according to its temperature.

C1E SupportUse this item to decrease the bus ratio that reduces the consumption of CPU electricity andpower.

Intel (R) SpeedStep (tm) tech.Use this item to enable or disable the Intel SpeedStep Technology, which is only for the IntelCPU supporting the SpeedStep Technology function.

Venderpool TechnologyUse this item to enable or disable the Venderpool Technology, which is only for the CPUsupporting the VT function.

DRAM DrivingWhen this item is defaulted at “Normal”, some DDRs might cause the problem of bootingor system stability; in that case, please set it at “High”.

31

Using BIOS

Features SetupThis page sets up some parameters for peripheral devices connected to the system.

OnBoard Floppy ControllerUse this item to enable or disable the onboard floppy disk drive interface.

OnBoard Serial PortUse this item to enable or disable the onboard COM1 serial port, and to assign a port address.

OnBoard IR PortUse this item to enable or disable the onboard infrared port, and to assign a port address.

Onboard Parallel PortThis item enables or disables the onboard LPT1 parallel port, and assigns a port address.The Auto setting will detect and available address.

Parallel Port ModeUse this item to set the parallel port mode. You can select Normal (Standard Parallel Port),ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or EPP & ECP.

Parallel Port IRQUse this item to assign IRQ to the parallel port.

Parallel Port DMAUse this item to assign a DMA channel to the parallel port.

OnBoard PCI IDEUse this item to enable or disable the onboard PCI IDE channel.

OnBoard SATA-IDEUse this item to select RAID mode, IDE mode or Disabled for onboard SATA-IDE.

Audio DeviceThis item enables or disables the AC’97 audio chip.

MODEM DeviceThis item enables or disables the MC’97 modem chip.

Ethernet DeviceThis item enables or disables the onboard Ethernet LAN.

OnBoard LAN Boot ROMUse this item to enable or disable the LAN Boot ROM function.

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.Features Setup

Help Item

Allows BIOS to Enable orDisable Floppy Controller.

OnBoard Floppy ControllerSerial Port1 AddressOnBoard IR PortParallel Port Address Parallel Port Mode ECP Mode DMA Channel Parallel Port IRQOnBoard PCI IDE ControllerOnboard SATA-IDEAudio DeviceMODEM DeviceEthernet DeviceOnBoard LAN Boot RomOnBoard USB FunctionUSB Function For DOS

Enabled3F8/IRQ4Disabled378ECPDMA3IRQ7BothIDEEnabledAutoEnabledDisabledEnabledDisabled

32

Using BIOSPress <Esc> to return to the main menu setting page.

OnBoard USB FunctionEnable this item if you plan to use the USB ports on this motherboard.


Power Mangement SetupThis page sets up some parameters for system power management operation.

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.Power Management Setup

ACPI Aware O/S YesPower Management EnabledACPI Enhanced Efficiency DisabledSuspend Time Out DisabledResume on RTC Alarm DisabledLAN/Ring Power On DisabledKeyboard Power On Disabled Wake-Up Key Any Key

Help Item

Yes / NoACPI support for OperatingSystem.Yes: If OS supports ACPI.No: If OS does not supportACPI.

ACPI Aware O/SThis itme supports ACPI (Advanced Configuraion and Power Management Interface). Usethis item to enable or disable the ACPI feature.

Power ManagementUse this item to enable or disable a power management scheme. If you enable powermanagement, you can use this item below to set the power management operation. BothAPM and ACPI are supported.

ACPI Enhanced EfficiencyUse this item to enable or disable the function of ACPI enhanced efficiency.

Suspend Time OutThis item sets up the timeout for Suspend mode in minutes. If the time selected passeswithout any system activity, the computer will enter power-saving Suspend mode.

Resume on RTC AlarmThe system can be turned off with a software command. If you enable this item, the systemcan automatically resume at a fixed time based on the system’s RTC (realtime clock). Usethe items below this one to set the date and time of the wake-up alarm. You must use an ATXpower supply in order to use this feature.

LAN/Ring Power OnThe system can be turned off with a software command. If you enable this item, the systemcan automatically resume if there is an incoming call on the Modem/

Ring, or traffic on the network adapter. You must use an ATX power supply in orderto use this feature.Keyboard Power On/Wake-Up KeyIf you enable this item, the system can automatically resume by pressing any keys, hot key,power key on the keyboard, or typing in the password. You must use an ATX power supplyin order to use this feature.

33

Using BIOS

PCI / Plug and Play Setup PageThis page sets up some parameters for devices installed on the PCI bus and those utilizingthe system plug and play capability.


CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.PCI / Plug and Play Setup

Help ItemPrimary Graphics Adapter PCIShare Memory Size 32 MBAllocate IRQ to PCI VGA YesPCI IDE BusMaster Disabled

Select which graphics controllerto use as the primary boot device.

Primary Graphics AdapterThis item indicates if the primary graphics adapter uses the PCI or the AGP bus. The defaultPCI setting still lets the onboard display work and allows the use of a second display cardinstalled in an AGP slot.

Share Memory SizeThis item lets you allocate a portion of the main memory for theonbaord VGA displayapplication with several options.

Allocate IRQ to PCI VGAIf this item is enabled, an IRQ will be assigned to the PCI VGA graphics system. You set thisvalue to No to free up an IRQ.

PCI IDE BusMasterThis item enables or disables the DMA under DOS mode. We recommend you to leave thisitem at the default value.

34

Using BIOS

BIOS Security Features Setup PageThis page helps you install or change a password.

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.BIOS Security Features Setup

Security Settings

Supervisor Password : Not InstalledChange Supervisor Password Press Enter

Help Item

Install or Change the password.

Supervisor PasswordThis item indicates whether a supervisor password has been set. If the password has beeninstalled, Installed displays. If not, Not Installed displays.

Change Supervisor PasswordYou can select this option and press <Enter> to access the sub menu. You can use the submenu to change the supervisor password.

CPU PnP Setup PageThis page helps you manually configure the mainboard for the CPU. The system willautomatically detect the type of installed CPU and make the appropriate adjustments to theitems on this page.

ManufacturerThese items show the brand of the CPU installed in your system.

Ratio StatusThis item shows the Locked/Unlocked ratio status of CPU installed in your system.

CPU Over-clocking Func.This item decides the CPU over-clocking function installed in your system. If the over-clocking fails, please turn off the system power. And then, hold the PageUp key (similar tothe Clear CMOS function) and turn on the power, the BIOS will recover the safe default.

CPU FrequencyThis item shows the frequency of the CPU installed in your system.

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.CPU PnP Setup

Help ItemManufacturer: IntelRatio Status LockedCPU Over-clocking Func. DisabledCPU Frequency 200 MHzDRAM Frequency Auto

35

Using BIOS


DRAM FrequencyThis item shows the frequency of the DRAM in your system.

Hardware Monitor PageThis page sets up some parameters for the hardware monitoring function of this motherboard.

CMOS SETUP UTILITY – Copyright (C) 1985-2003, American Megatrends, Inc.Hardware Monitor Setup

Help Item ***System Hardware Monitor***

Vcore 1.504 VVdimm 2.496 VVivdd 2.608 VVcc5V 5.107 VSB3V 3.296 VVBAT 3.264 VCPU Temperature 41oC/105oFSYSTEM Temperature 32oC/89oFCPU FAN Speed 4560 RPMSYSTEM FAN Speed 0 RPMSmart FAN Temp. Limit of Full Disabled

CPU/System TemperatureThese items display CPU and system temperature measurement.

FANs & Voltage MeasurementsThese items indicate cooling fan speeds in RPM and the various system voltage measure-ments.


36

Using BIOS

If you have made settings that you do not want to save, use the “DiscardChanges and Exit” item and press <OK> to discard any changes you havemade.

Load Optimal DefaultsThis option opens a dialog box to ask if you are sure to install optimized defaults or not. Youselect [OK], and then press <Enter>, the Setup Utility loads all default values; or select[Cancel], and then press <Enter>, the Setup Utility does not load default values.

Save Changes and ExitHighlight this item and press <Enter> to save the changes that you have made in the SetupUtility configuration. When the Save Changes and Exit dialog box appears, select [OK] tosave and exit, or select [Cancel] to return to the main menu.

Discard Changes and ExitHighlight this item and press <Enter> to discard any changes that you have made in theSetup Utility and exit the Setup Utility. When the Discard Changes and Exit dialog boxappears, select [OK] to discard changes and exit, or select [Cancel] to return to the mainmenu.

37


Chapter 4


About the Software CD-ROMThe support software CD-ROM that is included in the motherboard package contains all thedrivers and utility programs needed to properly run the bundled products. Below you can finda brief description of each software program, and the location for your motherboardversion. More information on some programs is available in a README file, located in thesame directory as the software.

Never try to install all software from folfer that is not specified for use with yourmotherboard.

Before installing any software, always inspect the folder for files named README.TXT,INSTALL.TXT, or something similar. These files may contain important information thatis not included in this manual.

Auto-installing under Windows 98/ME/2000/XPThe Auto-install CD-ROM makes it easy for you to install the drivers and software for yourmotherboard.

If the Auto-install CD-ROM does not work on your system, you can still installdrivers through the file manager for your OS (for example, Windows Ex-plorer). Refer to the Utility Folder Installation Notes later in this chapter.

The support software CD-ROM disc loads automatically under Windows 98/ME/2000/XP.When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automati-cally bring up the install screen. The screen has three buttons on it, Setup, Browse CD andExit.

If the opening screen does not appear; double-click the file “setup.exe” in theroot directory.

38


Setup Tab

Setup Click the Setup button to run the software installation program. Selectfrom the menu which software you want to install.

Browse CD The Browse CD button is the standard Windows command that allowsyou to open Windows Explorer and show the contents of the supportCD.

Before installing the software from Windows Explorer, look for a filenamed README.TXT, INSTALL.TXT or something similar. This filemay contain important information to help you install the softwarecorrectly.

Some software is installed in separate folders for different operatingsystems, such as DOS, WIN NT, or WIN98/95. Always go to the correctfolder for the kind of OS you are using.

In install the software, execute a file named SETUP.EXE or INSTALL.EXEby double-clicking the file and then following the instructions on thescreen.

Exit The EXIT button closes the Auto Setup window.

Application TabLists the software utilities that are available on the CD.

Read Me TabDisplays the path for all software and drivers available on the CD.

Users please note for models with Azalia Audio, the Intel High Definitionaudio functionality unexpectedly quits working in Windows Server 2003 Ser-vice Pack 1 or Windows XP Professional x64 Edition.

RESOLUTION:Download and install the update packages from the Microsoft DownloadCenter. The download pages for each respective OS are listed as below—Windows Server 2003, 32-Bit Editionshttp://www.microsoft.com/downloads/details.aspx?FamilyId=D0934D06-15B3-4A65-8C52-746BEB24E86C&displaylang=en

Windows Server 2003, x64 Editionshttp://www.microsoft.com/downloads/details.aspx?FamilyId=0E850506-50EE-4458-902F-F9FC59201B04&displaylang=en

Microsoft Windows XP Professional x64 Editionhttp://www.microsoft.com/downloads/details.aspx?FamilyId=DAB139F1-065C-41E8-A148-9D79BD9D24F9&displaylang=en

For more detailed information about how to fix the regarding problem,please log on to http://support.microsoft.com/default.aspx?scid=kb;en-us;901105#appliesto for help and support.

39


The following screens are examples only. The screens and driver lists willbe different according to the motherboard you are installing.

The motherboard identification is located in the upper left-hand corner.

Running SetupFollow these instructions to install device drivers and software for the motherboard:

1. Click Setup. The installation program begins:

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default optionsare recommended.

40


5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the onscreen instruc-tions, confirm commands and allow the computer to restart a few times to complete theinstallation.

4. Click Next run the Installation Wizard. An item installation screen appears:

Manual InstallationInsert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory.This file contains the information needed to locate the drivers for your motherboard.

Look for the chipset and motherboard model; then browse to the directory and path tobegin installing the drivers. Most drivers have a setup program (SETUP.EXE) that auto-matically detects your operating system before installation. Other drivers have the setupprogram located in the operating system subfolder.

If the driver you want to install does not have a setup program, browse to the operatingsystem subfolder and locate the readme text file (README.TXT or README.DOC) forinformation on installing the driver or software for your operating system.

Utility Software Reference

All the utility software available from this page is Windows compliant. They are providedonly for the convenience of the customer. The following software is furnished under licenseand may only be used or copied in accordance with the terms of the license.

These software(s) are subject to change at anytime without prior notice.Please refer to the support CD for available software.

41


AMI/AWARD Flash UtilityThis utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard,and lets you copy an updated version of the BIOS to the chip. Proceed with caution whenusing this program. If you erase the current BIOS and fail to write a new BIOS, or write anew BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS formore information.

WinFlash UtilityThe Award WinFlash utility is a Windows version of the DOS Award BIOS flash writer utility.The utility enables you to flash the system BIOS stored on a Flash Memory chip on themotherboard while in a Windows environment. This utility is currently available forWINXP\ME\2000\98SE. To install the WinFlash utility, run WINFLASH.EXE from thefollowing directory: \UTILITY\WINFLASH 1.51

This concludes Chapter 4.

42


Memo


Français

Les chipsets P4M800 Northbridge (NB) et VT8237 Southbridge (SB) sont basés sur une architecture novatrice et dimensionnable avec une fiabilité et des performances prouvées.

Chipset

• North Bridge UMA de haute-performance : Pentium 4 North Bridge intégré avec support FSB 800 MHz et Contrôleurs Graphiques & Vidéo UniChrome Pro 3D / 2D dans une simple puce

• Prend en charge les processeurs Pentium 4 et Pentium M FSB Intel 800/533 MHz et la technologie Hyper Threading

• Conforme AGP v3.0 avec mode de transfert en 8x/4x avec prise en charge de Fast Write

• Prend en charge les types de mémoire DDR400/333/266 avec interface DRAM 2.5V SSTL-2

• Prend en charge les modes de transfert 66 MHz, 4X et 8X, interface V-Link avec bande passante totale de 533 Mo/s

• Bus ACPI 2.0 et PCI conformes à Power Management 1.1• Moteur graphique avec horloge allant jusqu’à 133 MHz

découplé de l’horloge mémoire

CaractéristiquesProcesseurLa carte mère utilise un type LGA775 de Pentium 4/Pentium D/Celeron D présentant les fonctionnalités suivantes :

• Reçoit des processeurs Intel Pentium 4/Pentium D/Celeron D• Prend en charge un bus système (FSB) de 800 MHz• Prend en charge le CPU de technologie " Hyper-Threading"

La technologie “Hyper-Threading” permet au système d’exploitation de penser qu’il est connecté à deux processeurs, permettant d’exécuter deux threads en parallèle, à la fois sur des processeurs «logiques» séparés dans le même processeur physique.

VIA P4M800 (NB)

VT8237 (SB) • Transit de données PCI vers mémoire système jusqu’à 132 Mo/sec(données envoyées au north bridge via Interface Ultra V-Link haute vitesse)

• Conforme PCI-2.2, interface PCI 3.3V 32 bits avec entrée à tolérance 5V

• Prend en charge trois logements PCI d’arbitrage et de décodage pour toutes les fonctions intégrées et bus LPC.

• Contrôleur ATA/RAID Série Double Canal —Conforme aux Spécifications ATA Série Révision 1.0

Mémoire• Deux sockets DIMM de 2,5V 184 broches pour module mémoire DDR

SDRAM• Supporte le bus mémoire DDR 400/333/266 • La mémoire maximum installée est 2Go

• Trois logements PCI 32 bits• Un logement 8X AGP• Un logement CNR

Logements d’Extension


Français

• Solution à couche physique 100Base-TX/10Base-T à simple puce • Double Vitesse – 100/10 Mbps• Half et Full Duplex• Interface MII vers Contrôleur Ethernet• Interface MII pour Configuration & Etat• Mode Economie d’énergie automatique• Négociation automatique : 10/100, Full/Half Duplex • Conforme à tous les Standards IEEE802.3, 10Base-T et 100Base-TX

Applicables• Forme d’onde sur puce – Pas de filtre externe requis.• Egaliseur adaptatif.• Correction de déviation de base• Sorties LED

AC’97 CODEC• Conforme au CODEC AC’97 (Rev 2.3).• Détection de prise de Sortie Avant, Sortie Contour, Entrée MIC et Entré

Ligne• Trois entrées stéréo de niveau de ligne analogique avec contrôle de

volume 5 bits : LINE_IN, CD, AUX• Deux entrées mono de niveau de ligne analogique• LQFP 48 broches• Tampon d’écouteurs intégré et PLL interne.

• Prend en Charge les modes PIO (Entrée/Sortie Programmable) et DMA (Accès Direct à la Mémoire)

• Supporte maîtrise de bus Ultra DMA IDE avec vitesse de transfert de 133/100/66 Mo/sec

• Deux ATA Série connecteurs• Vitesse de transfert supérieure au meilleur ATA (~150 Mo/s) avec extensi-

bilité aux vitesses supérieures • Comptage de broche faible pour l’hôte et les périphériques

Canaux IDE internes

ATA Série

• Deux ports PS/2 pour souris et clavier• Un port série• Un port parallèle• Un port VGA• Quatre USB 2.0 ports fond de panier• Un port LAN (optionnel)• Prises audio pour microphone, ligne d’entrée et ligne de sortie

Ports E/S Internes

Fast Ethernet LAN (optionnel)


Français Microprogramme BIOS

La carte mère utilise AMI BIOS qui permet aux utilisateurs de configurer de nombreuses caractéristiques du système comprenant les suivantes:

• Gestion de l’alimentation• Alarmes de réveil• Paramètres de CPU• Synchronisation du CPU et de la mémoire

Le microprogramme peut aussi être utilisé pour définir les paramètres pour les vitesses d’horloges de différents processeurs.

Certaines spécifications matérielles et éléments de logiciels peuvent être modifiés sans avertissement.


Deutsche

Die P4M800 Northbridge (NB) und VT8237 Southbridge (SB) Chipsätze basieren auf einer innovativen und skalierbaren Architektur mit bewiesener Zuverlässigkeit und Leistung.

Chipsatz

• Hochleistungsfähiger UMA-North Bridge: Integrierter Pen-tium 4 North Bridge mit Unterstützung für 800 MHz FSB und UniChrome Pro 3D-/ 2D-Grafik & Videocontroller in einem einzelnen Chip

• Unterstützt Intel 800/533 MHz FSB Pentium 4 und Pentium M Prozessoren und Hyper-Threading-Technologie

• Gemäß AGP v3.0 mit einem Transfermodus von 8x/4x und Fast Write-Unterstützung

• Er unterstützt DDR400/333/266 Speichertypen mit einer 2.5V SSTL-2 DRAM Schnittstelle

• Unterstützt 66 MHz, 4X und 8X Transfermodi, V-Link-Interface mit einer Bandbreite von insgesamt 533 MB/s

• Entspricht ACPI 2.0 und PCI-Bus Power Management 1.1• Grafik-Engine taktet bis zu 133 MHz entkoppelt vom

Speichertakt

FeatureProzessorDieses Mainboard verwendet einen LGA775 Typ Intel Pentium 4/Pentium D/Celeron D mit den folgenden Eigenschaften:

• Nimmt Intel Pentium 4/Pentium D/Celeron D Prozessoren auf• Unterstützt einen Systembus (FSB) mit 800 MHz• Unterstützt eine CPU mit „Hyper-Threading“ Technologie

VIA P4M800 (NB)

VT8237 (SB)

Bei der „Hyper-Threading” Technologie „denkt” das Betriebssystem, dass es an zwei Prozessoren angeschlossen ist. Dadurch können im selben physikalischen Prozessor zwei Threads parallel auf separaten „logischen“ Prozessoren laufen.

• PCI-to-System Memory Data Streaming mit bis zu 132MB/sek. (Daten werden über das Hochgeschwindigkeits Ultra V-Link-Interface zur Northbridge gesendet)

• Kompatibel mit PCI-2.2. 32-Bit 3.3 Volt PCI-Interface mit 5 Volt-toleranten Eingängen

• Unterstützt drei PCI-Steckplätze mit Vermittlung und Dekodierung für alle integrierten Funktionen sowie den LPC-Bus

• Dualkanal-Serial ATA/RAID-Controller—Entspricht der Serial ATA-Spezifikationsrevision 1.0

Speicher• Zwei 184-pin 2.5V DIMM Steckplätze für DDR SDRAM• Unterstützung für DDR 400/333/266 Speicherbus• Maximal auf 2GB Speicher erweiterbar

• Drei 32-Bit PCI-Steckplätze • Ein 8X AGP-Steckplatz• Ein CNR-Steckplatz

Erweiterungssteckplätze


Deutsche

• Single-Chip 100Base-TX/10Base-T Bitübertragunsschicht-Lösung• Duale Geschwindigkeit – 100/10 Mbps.• Halb- und Vollduplex• MII Interface-zu-Ethernet Controller• MII-Interface zu Konfiguration & Status• Automatischer Energiesparmodus• Auto-Negotiation: 10/100, Voll/Halfduplex• Entspricht allen anwendbaren Standards: IEEE802.3, 10Base-T und

100Base-TX• On-Chip Waveshaping – Keine externen Filter notwendig.• Adaptiver Equalizer.• Baseline-Wander-Korrektur• LED-Ausgänge

AC’97 CODEC• Entspricht AC’97(Rev 2.3) CODEC • Front-Out, Surround-Out, MIC-In und LINE-In-Jack Sensing • Drei analoggleiche Stereo-Eingänge mit einer 5-Bit Lautstärkenkontrolle:

LINE_IN, CD, AUX• Zwei analoge Line-Level Mono-Eingänge• 48-Pin LQFP• Integrierter Kopfhörerpuffer und interne PLL

Onboard IDE-Kanäle• Unterstützt die Modi PIO (Programmable Input/Output) und DMA (Direct

Memory Access)• Unterstützung für IDE Ultra DMA-Busmastering mit Transferraten von

133/100/66 MB/Sek

• Zwei Serial ATA-Anschlüssen• Datentransferrate übertrifft beste ATA-Werte (~150 MB/Sek.); höhere Trans-

ferraten möglich• Low Pin Count (LPC) für Host und Geräte

Serial ATA

• Zwei PS/2-Steckplätze für Maus und Tastatur yboard • Ein serieller Steckplatz• Ein paralleler Steckplatz• Ein VGA Steckplatz• Vier USB 2.0 Ports auf der Rückseite • Ein LAN Steckplatz (optional)• Audioanschlüsse für Mikrofon, line-in und line-out

Onboard I/O Schnittstellen

Fast Ethernet LAN (optional)


Deutsche

BIOS FirmwareDieses Motherboard setzt das AMI BIOS ein, mit dem der Anwender viele Systemeigenschaften selbst konfigurieren kann, einschließlich der folgenden:

• Energieverwaltung• Wake-up Alarm• CPU-Parameter • CPU- und Speichertiming

Mit der Firmware können auch Parameter für verschiedene Prozessortaktgeschwindigkeiten eingestellt werden.

Einige Hardware- und Software-Spezifikationen können jederzeit und ohne vorherige Ankündigung geändert werden.


Italiano

I chipset P4M800 Northbridge (NB) e VT8237 Southbridge (SB) sono basati su un’innovativa architettura scalabile e offrono collaudata affidabilità e prestazioni comprovate.

Chipset

• North Bridge UMA a elevate prestazioni: North Bridge Pentium 4 integrato con supporto di FSB a 800 MHz e controller Video e Grafica 3D / 2D UniChrome Pro in un unico chip

• Supporto di processori Intel Pentium M e Pentium 4 FSB a 800/533 MHz, nonché di tecnologia Hyper-Threading.

• Conforme allo standard AGP v3.0 8x/4x con supporto Fast Write

• Supporta tipi di memoria DDR400/333/266 con interfaccia 2.5V SSTL-2 DRAM

• Supporto di interfaccia Ultra V-Link a 66 MHz, modalità di trasferimento 4X e 8X, con larghezza di banda totale di 533 MB/sec.

• Conforme ad ACPI 2.0 e PCI Bus Power Management 1.1• Clock del motore grafico fino a 133 MHz indipendenti dal clock

della memoria

CaratteristicheProcessoreP4M800-M7 si avvale di un tipo LGA775 di Pentium 4 /Celeron D che offre le seguenti caratteristiche:

• Alloggia processori Intel Pentium 4/Pentium D/Celeron D• Supporto di un bus di sistema (FSB) da 800/533 MHz• Supporto di CPU con tecnologia “Hyper-Threading”

P4M800 (NB)

VT8237 (SB)

La tecnologia “Hyper-Threading” simula per il sistema operativo una sorta di doppio processore e consente a due processi di essere eseguiti in parallelo, ciascuno su un diverso processore “logico” all’interno del medesimo processore fisico.

• Velocità di Trasmissione Data da PCI a memoria di sistema fino a 132Mbyte/sec (dati spediti al north bridge tramite inter-faccia ad alta velocità Ultra V Link)

• Supporto Stardard PCI 2.2, Interfaccia PCI 3.3V a 32 bit con tolleranza in input di 5V

• Supporto di tre slots PCI con arbitrato e decoding per tutte le funzioni integrate ed il bus LPC.

• Controller seriale ATA/RAID a Doppio Canale— Compatibile con le specifiche “Serial ATA Specification Revision 1.0”

Memoria• Due prese DIMM da 2,5 V a 184 pin per moduli memoria SDRAM DDR• Supporta bus di memoria DDR 400/333/266 • Quantità massima di memoria installabile, 2GB

Slot di espansione• Tre slot PCI a 32 bit • Una slot AGP 8X• Uno slot CNR


Italiano

• Soluzione livello fisico 100Base-TX/10Base-T a chip unico• Doppia velocità – 100/10 Mbps• Half/Full Duplex• Interfaccia MII su Ethernet Controller• Interfaccia MII per funzionalità di configurazione e stato• Modalità risparmio di energia automatica.• Negoziazione Automatica: 10/100, Full/Half Duplex• Supporto di tutti gli standard esistenti IEEE802.3, 10Base-T e 100Base-

TX• Elaborazione onda su chip - nessuna necessità di filtri esterni.• Equalizzatore adattabile.• Correzione mobile su baseline• Uscite LED

AC’97 CODEC • Conforme a AC’97 (Rev 2.3) CODEC.• Rilevazione dei jack Front-Out, Surround-Out, MIC-In e LINE-In• Tre input stereo line-level analogici con controllo volume a 5 bit: LINE_IN,

CD, AUX• Due ingressi di linea analogica-mono• LQFP a 48 pin • Buffer auricolare integrato e PLL interno.

• Due porte PS/2 per tastiera e mouse• Una porta seriale• Una porta parallela• Una porta VGA• Quattro porte USB2.0 presenti nella parte posteriore• Una porta LAN (opzionale)• Jack audio per microfono, ingresso linea e uscita linea

• Supporto della modalità PIO (Programmable Input/Output) e DMA (Direct Memory Access)

• Supporto per le modalità Bus Mastering e Ultra DMA ATA 133/100/66 MB/sec

Canali IDE Integrati

Onboard I/O Porte

• Due connettori Serial ATA• Altissima velocità di trasferimento dati ATA (~150 MB/s) con la possibilità

di scalabilità della velocità stessa verso valori piú alti• Pin Count ridotto sia per l’host sia per le periferich

ATA Seriale

Fast Ethernet LAN (opzionale)


Italiano

Firmware BIOS La scheda madre si avvale del BIOS AMI che consente la configurazione personalizzata di molte funzionalità del sistema, tra cui:

• Gestione dell’alimentazione• Allarmi di attivazione• Parametri CPU• Sincronizzazione di CPU e memoria

Il firmware consente inoltre di impostare i parametri per diverse velocità di clock del processore.

Alcune specifiche hardware e voci di software possono essere modificate senza preavviso.


Español

El chipset P4M800 Northbridge (NB) y VT8237 Southbridge (SB) se basan de una arquitectura innovadora y escalable con fiabilidad y rendimiento comprobados.

Chipset

• UMA North Bridge de Alto Rendimiento: Pentium 4 North Bridge integrado con soporte FSB de 800 MHz y Contro-ladores de Gráficas & Vídeo 3D/2D UniChrome Pro en un solo chip

• Soporta procesadores Intel 800/533 MHz FSB Pentium 4 y Pentium M y la Hyper Threading Technology

• Conformidad AGP v3.0 con modo de transferencia 8X/4X con soporte Fast Write

• Soporta los tipos de memoria DDR400/333/266 con interfaz 2.5V SSTL-2 DRAM\

• Soporta los modos de transferencia 66 MHz, 4X y 8X, interfaz V-Link con banda ancha total de 533 MB/seg

• Conformidad de Administración de Suministro 1.1 de Bus PCI de ACPI 2.0 1.1

• Relojes de motor de gráficas hasta 133 MHz desacoplado del reloj de memoria

CaracterísticaProcesadorLa placa principal usa un tipo LGA775 de Intel Pentium 4/Celeron que lleva las sigtes. características:

• Acomoda procesadores Intel Pentium 4/Pentium D/Celeron D• Soporta un bus de sistema (FSB) de 800MHz• Soporta la CPU con tecnología "Hyper-Threading"

La tecnología “Hyper-Threading” habilita el sistema operativo en pensar que está conectado a dos procesadores, que permite dos hilos a correr en paralelo, ambos en procesadores "lógicos" separados dentro de un mismo procesador físico.

P4M800 (NB)

VT8237 (SB) • PCI para datos de la memoria del sistema que corren hasta 132 Mb/por segundo(datos enviados a north bridge mediante Interfaz de alta velocidad Ultra V-Link)

• Conformidad PCI-2.2, interfaz PCI 32-bit 3.3V con entradas tolerantes de 5V

• Soporta tres ranuras PCI de arbitración y decoficación para todas las funciones integradas y bus LPC.

• Controlador ATA/RAID Serial de Canal Dual—Conformi-dad con la Especificación ATA Serial Revisión 1.0

Memoria• Dos zócalos DIMM de 184-pin 2.5V para los módulos de memoria DDR

SDRAM• Soporta el bus de memoria DDR 400/333/266 • Memoria máxima instalada es 2GB


Español

• Solución de capa física de 100Base-TX/10Base-T de un solo chip• Velocidad Dual – 100/10 Mbps• Duplex Medio y Completo • Interfaz MII para el Controlador de Ethernet• Interfaz MII a Configuración & Estado• Modo Ahorro de Energía Automático• Autonegociación: 10/100, Duplex Completo/Medio

• Tres ranuras 32-bit PCI • Una ranura 8X AGP• Una ranura CNR

Ranuras de Expansión

AC’97 Audio Codec• Conforme con el CODEC AC’97(Rev 2.3)• Deteccion de Clavija de Salida de Frente, Salida Surround, Entrada de

Microfono y Entrada de Linea• Tres entradas de estéreo a nivel de línea analógica con control de volumen

de 5-bit: LINE_IN, CD, AUX• Dos entradas mono a nivel de linea analogica • 48-Pin LQFP estandar• Buffer de audífono incorporado y PLL interno.

• Dos puertos PS/2 para ratón y teclado• Un puerto serial • Un puerto paralelo• Un puerto VGA• Cuatro puertos USB2.0 de panel trasero• Un puerto LAN (optativo)• Clavijas de sonido para micrófono, entrada y salida de línea

• Soporta modos PIO (Entrada/Salida Programable/Programmable Input/Out-put) y modos DMA (Acceso de Memoria Directo/Direct Memory Access).

• Soporta mastering de bus IDE Ultra DMA con índices de transferencia de 133/100/66 MB/seg

Canales IDE abordo

Puertos I/O Abordos

• Dos conectores Serial ATA• Índice de transferencia que excede el mejor ATA (~150 MB/s) con escalabili-

dad a índices superiores• Cuenta de pin baja para ambos anfitrión y dispositivos

ATA Serial

Ethernet LAN Rápido (optativo)


Español

BIOS FirmwareLa placa principal usa AMI BIOS que habilita usuarios para configurar muchas características de sistema que incluyen las sigtes:

• Administración de Alimentación • Alarmas para despertar • Parámetros de CPU • Cronometraje de CPU y de memoria

También se lo puede usar el firmware para configurar los parámetros para diferentes velocidades de reloj de procesador.

Algunas especificaciones de hardware e ítems de software son sujetos a cambio sin aviso previo.

• Satisface Todas las Normas Aplicables IEEE802.3, 10Base-T y 100Base-TX • Forma de Onda En Chip – Sin Necesitar Filtros Externos• Ecualizador Adaptivo.• Corrección de desvío de línea base• Salidas de LED


PortuguêsO conjunto de chips P4M800 Northbridge (NB) e VT8237 Southbridge (SB) é baseado numa

arquitectura inovadora e escalável com fiabilidade e performance provadas.

Conjunto de Chips

• North Bridge UMA de Elevada Performance: North Bridge Pentinum 4 integrada com suporte 800 MHz FSB e Gráficos 2D / 3 D UniChrome e Controladores de Vídeo num único chip

• Suporta Intel 800/533 MHz FSB Pentium 4 e Processadores Pentium M e Tecnologia Hyper-Entrelaçamento

• AGP v3.0 em conformidade com 8x/4x modulo de transferência com apoio Fast Write (Escrita Rápida)

• Suporte para tipos de memória DDR333/266 com interface 2.5V SSTL-2 DRAM

• Suporta modos de transferência 66 MHz, 4X e 8X, V-Link interface com banda total de 533 MB/seg

• Compatível com Gestão 1.1. de Potência de Bus PCI e ACPI 2.0

• O Engenho gráfico cronometra até 133 MHz decopulado da memório do relógio

CaracterísticasProcessadorEsta motherboard usa um tipo LGA775 de Intel Pentium 4/Pentium D/Celeron D que possui as seguintes características:

• Acomoda processadores Intel Pentium 4/Pentium D/Celeron D• Suporta um bus de sistema (FSB) de 800MHz• Suporta CPU de tecnologia “Hyper Threading”

Tecnologia “Hyper Threading” que permite ao sistema funcionar de forma interligada até dois processadores, permitindo que os dois fios possam funcionar em paralelo, ambos em processadores “lógicos” separados dentro do mesmo processador físico.

VIA P4M800 (NB)

VT8237 (SB) • PCI para corrente do sistema de memória de dados até 132Mbyte/seg (dados enviados à ponte norte via interface Ultra V-Link de alta velocidade)

• PCI-2.2 complacente , 32-bit 3.3V PCI interface com inputs tolerantes 5V

• Suporta três encaixes PCI de arbitração e decodificação para todas as funções integradas e LPC bus.

• Controlador do Canal Duplo Serial ATA/RAID—Compatível com a Revisão de Especificação em Série ATA 1.0

Memória• Duas fichas DIMM 2.5V com 184 pinos para módulos de memória DDR

SDRAM• Suporta bus de memória DDR 400/333/266 • A memória máxima instalada é de 2GB

Slots de expansão• Três slots PCI de 32 bit• Um slot AGP 8X• Um slot CNR


Português

AC’97 Audio Codec• Complacente ao AC’97(Rev 2.3) CODEC. • Saída Frontal, Saída Surround, Sensor de Tomada MIC-In e LINE-In • Três entradas estéreo de nível de linha e analógicas com controlo de volume

5-bit: LINE_IN, CD, AUX• Duas entradas mono nível de linha analógicas• LQFP de 48 pinos standard• Fones de ouvido embutidos e PLL interno

• Suporta modos PIO (Input/Output Programável) e DMA (Direct Memory Access)

• Suporta IDE Ultra DMA bus mastering com razão de transferência de 133/100/66 MB/seg

• Duas portas PS/2 para o rato e teclado• Uma porta série• Uma porta paralela• Uma porta VGA• Quatro portes USB2.0 traseiros• Uma porta LAN (opcional)• Jacks audio para microfone, line-in e line-out

Canais IDE na placa

Portas I/O na placa

• Duas conectores Série ATA • Razão de transferência excedendo o melhor ATA (~150 MB/s) com escal-

abili dade para razões mais altas• Contagem baixa de pin para ambos os dispositivos e host

Série ATA

• Solução de passagem 100Base-TX/10Base-T física com um único chip• Velocidade Dupla – 100/10 Mbps• Duplex Completo e Parcial• Suporta interface MII para controlador Ethernet• MII Interface à Configuração & Status• Modo de Economia de Energia Automática.• Auto Negociação: 10/100, Full/Half Duplex• Satisfaz todos os Padrões IEEE802.3, 10Base-T e 100Base-TX Aplicáveis• Chip Wave Shaping embutido – Nenhum Filtro Externo é exigido.• Equalizador Adaptativo.• Saídas de Correção Básica • LED

Fast Ethernet LAN (opcional)


Português

Microprogramação BIOSEsta motherboard usa AMI BIOS que permitem aos utilizadores configurar muitas características do sistema incluindo as seguintes:

• Gestão de corrente• Alarmes de despertar• Parâmetros CPU• Temporização de memória e CPU

A microprogramação poderá ser também usada para estabelecer parâmetros para diferentes velocidades de relógio do processador.

Algumas especificações de hardware e itens de software poderão ser sujeitos a alteraçõessem aviso prévio.


日本

語

チップセットP4M800 Northbridge (NB)と VT8237 Southbridge (SB)チップセットは、実証された信頼性と性能を持つ革新的で拡張性のあるアーキテクチャに基づいています。

• 高性能UMA North Bridge：統合型Pentium 4 North Bridgeで、800 MHz のFSB をサポートし、UniChrome Pro 3D / 2D グラフィック&ビデオコントローラを一つのチップに統合

• Intel 800/533 MHz FSB のPentium 4 とPentium M のプロセッサに対応し、ハイパー・スレッディング・テクノロジをもサポート

• AGP v3.0 でFast Write対応の8x/4x 転送モードを提供• 2.5V SSTL-2 DRAM インターフェース付のDDR400/333/266 メ

モリをサポート• 66 MHzでの 4X と 8X の転送モードをサポートし、V-Linkインター

フェースで最大合計533 MB/秒の帯域幅を提供• ACPI 2.0 and PCI Bus Power Management 1.1に準拠• グラフィック・エンジンのクロック数がメモリのクロック数に規定され

ず最大133 MHz まで可能

機能

プロセッサ本マザーボードは LGA775タイプのIntel Pentium 4/Pentium D/Celeron D に対応したもので、次の特徴があります：

• Intel Pentium 4/Pentium D/Celeron Dプロセッサに対応

• 800 MHzのシステムバス(FSB)をサポート

• “ハイパースレッド” 技術をサポートハイパースレッド（HT）技術というのは、オペレーションシステムに2つのプロセッサが存在すると認識させることで、実際には2つのスレッドを1つのプロセッサで同時に執行させ、平行利用を可能とする技術です。

VIA P4M800 (NB)

VT8237 (SB) • PCIからシステムメモリへのデータストリームが最大132Mbyte/秒まで可能 (ノースブリッジへのデータの転送は高速のUltra V-Linkインターフェースを介する)

• PCI-2.2対応の32ビット3.3V PCIインターフェースを採用で、5V許容入力を提供

• 3つのPCIスロットを有し、統合機能やLPCバスに対する調停管理やデコードをサポート.

• デュアルチャネルSATA/RAID コントローラ-Serial ATA Specifi-cation Revision 1.0に対応

メモリ• DDR SDRAM メモリモジュール用の184ピン2.5V DIMM ソケットが2つ

• DDR400/333/266 のメモリバスをサポート

• 合計で最大2GBまでの容量に対応可能

拡張スロット• 32ビットPCI 互換性スロットが3つ

• 1つのAGP 8X スロット• 1つのCNR スロット


日本

語• シングルチップ100Base-TX/10Base-T 物理層ソリューションを採用• デュアル100/10 Mbpsをサポート• 半/全二重の動作可能• イーサーネットコントローラのMII インターフェースに対応• MIIインターフェース: 構成と状態を表示• 自動省電力モード• 自動折衝機能：10 / 100、全 /半二重• 適用可能のIEEE 802.3、10Base-T、および100Base-Tx 基準にすべて対応• オンチップのウェーブシェイピング機能 : これで外付けフィルタが不要に• 適応イコライザ• ベースライン・ワンダー・コレクタ• LED 出力

AC’97 オーディオ・コーデック• AC’97(Rev 2.3) CODECに準拠.• Front-Out、Surround-Out、 MIC-In およびLine-In ジャックの検出機能を搭

載• 3つのアナログ式の Lineレベルステレオ入力（5ビットボリュームコントロール可

能）： LINE_IN、CD、AUX• 2つのアナログ式Lineレベルもの入力• 48ピンLQFP.• 内蔵式イヤホンバッファおよび内部 PLL

オンボード入出力ポート

オンボードIDEチャネル• PIO (Programmable Input/Output) と DMA (Direct Memory Access)と

の転送モードをサポート• 100/66/33 MB/秒における IDE Ultra DMA バスマスタ機能をサポート

シリアル ATA• Serial ATA コネクタが2つ• 転送率が現存のATA (~150 MB/秒)の最高転送率よりも高く、将来においてさ

ならる向上が可能• ホスト側や装置側の連結端のピン数が従来よりも削減

• マウスとキーボード用のPS/2ポートが2つ• シリアルポートが1つ• パラレルポートが1つ• VGAポートが1つ• バックパネル USB2.0 ポートが4つ• LANポートが1つ(オプション)• マイク、ラインイン、ラインアウト用オーディオジャック

高速イーサーネット LAN 機能(オプション)


日本

語

BIOSファームウェア本マザーボードはAMI BIOSを採用し、次の機能を含む多様なシステムの構成ををサポートします。

• 電源管理• ウェークアップアラーム• CPUパラメータ• CPUとメモリとのタイミング

さらに、所定のパラメータを設定することによって、プロセッサのクロック速度を変更することもできます。

一部のハードウェア仕様とソフトウェアアイテムは、予告なしに変更することがあります。


한국

어

P4M800 Northbridge (NB) 및 VT8237 Southbridge (SB) 칩셋은 혁신적이고 범위성을 지닌 아키텍쳐를 기반으로 인정된 신뢰성과 성능을 지닌다.

칩셋

• 고성능 UMA North Bridge: 통합 팬티엄 4 North Bridge, 800 MHz FSB, 싱글 칩에 UniChrome Pro 3D / 2D 그래픽 및 비디오 컨트롤러 지원.

• 인텔 800/533 MHz FSB 팬티엄 4 및 팬티엄 M 프로세서 및

Hyper Threading 기술 지원 • AGP v3.0 부합, 8x/4x 전송 모드, Fast Write 지원• 2.5V SSTL-2 DRAM 인터페이스를 지닌 DDR333/266 메

모리 타입 지원

• 66MHz 지원, 4X 및 8X 전송 모드, 총 대역폭533 MB/sec의

Ultra V-Link 호스 트 인터페이스 • ACPI 2.0 및 PCI 버스 전원 관리 1.1 부합

• 메모리 클록에서 디커플된 최대 그래픽 엔진 클록 133

MHz

특성

프로세서본 마더보드는 LGA775 타입의 인텔 팬티엄 4/팬티엄 D/셀러론을 D 사용하여 다음과 같은 특성을 지닌다:

• Intel 팬티엄 4/팬티엄 D/셀러론을 D 프로세서 사용• 800MHz 의 시스템 버스 (FSB) 지원• "Hyper-Threading" 기술의 CPU 지원

"Hyper-Threading" 기술은 운영 체제가 두개의 프로세서에 연결되어 있는 것처럼, 두 트래드가 동일한 물리적 프로세서 안에 있으면서도 각기 다른 "논리적" 프로세서에서 패러럴로 실행되게 한다.

VIA P4M800 (NB)

VT8237 (SB) • PCI 에서 시스템 메모리로의 데이터 스트리밍 최대

132Mbyte/ sec (고속 울트라 V-Link 인터페이스를 통해

north bridge 로 보 내진 데이터)

• PCI-2.2 부합, 32-bit 3.3V PCI 인터페이스, 5V 입력

• PCI 슬롯 3 개 , 모든 통합 기능 및 LPC 버스를 위한 디코

딩 지원

• 듀얼 채널 시리얼 ATA/RAID 컨트롤러-시리얼 ATA 1.0

사양 부 합

메모리• DDR SDRAM 메모리 모듈을 위한 2 개의 184 핀 2.5V DIMM 소켓• DDR400/333/266 메모리 버스 지원 • 최대 설치 메모리 2GB

확장 슬롯• 32-bit PCI 슬롯 3 개• AGP 8X 슬롯 1 개• CNR 슬롯 1 개


한국

어

AC’97 오디오 코덱• AC’97(Rev 2.3) 코덱 호환• 프론트 출력, 서라운드 출력, 마이크 입력 및 라인 입력 잭 센싱. • 아날로그 라인 레벨 스테레오 입력 3 개, 5 비트 볼륨 제어: 라인 입력, CD,

AUX• 아날로그 라인 레벨 모노 입력 2 개• 표준 48 핀 LQFP• 내장 이어폰 버퍼 및 내부 PLL

• PIO (Programmable Input/Output) 및 DMA (Direct Memory Access) 모드 지원

• 전송 속도 33/66/100 MB/sec의 IDE Ultra DMA 버스 마스터링 지원

보드 내장 IDE

• 시리얼 ATA 커넥터 4 개 • 범위성을 지닌 최대 ATA (~150 MB/s) 를 능가하는 전송 속도• 호스트 및 장치의 적은 핀 수

시리얼 ATA

• 마우스 및 키보드 용 PS/2 포트 2 개• 시리얼 포트 1개• 패러럴 포트 1 개• VGA포트 1개• 후면 USB 2.0 포트 4 개

• LAN포트 1개(선택 사항)• 마이크의 라인 입력 및 라인 출력을 위한 오디오 잭

보드 내장 I/O 포트

패스트 이더넷 LAN (선택 사항)

• 싱글 칩 100Base-TX/10Base-T 물리적 계층 솔루션• 듀얼 스피드 100/10 Mbps• Half/Full Duplex• 이더넷 컨트롤러를 위한 MII 인터페이스• 구성 및 상태 MII 인터페이스• 자동 절전 모드• Auto Negotiation: 10 / 100, Full / Half Duplex• IEEE 802.3, 10Base-T 및 100Base-Tx 표준 모두 부합• 칩 내장 Wave Shaping - 외부 필터 필요 없음• Adaptive Equalizer.• Baseline wander Correction.• LED 출력


한국

어

BIOS 펌웨어본 마더보드는 다음과 같은 시스템 특성을 구성할 수 있는 AMI BIOS 를 사용한다:

• 전원 관리• Wake-up 알람• CPU 파라미터• CPU 및 메모리 타이밍

펌웨어로 다른 프로세서 클록 속도의 파라미터를 설정할 수도 있다.

몇 하드웨어 사양 및 소프트웨어 아이템은 사전 통보 없이 변경될 수 있습니다.


繁體中文

P4M800 北橋(NB)及VT8237 南橋(SB)晶片組在研發設計上採用了創新且具擴充性之架構，具備優良的可靠性及性能。

功能

處理器本主機板適用單顆 LGA775型Intel Pentium 4/Pentium D/Celeron D，且具有如下功能：

‧ 支援 Intel Pentium 4/Pentium D/Celeron D 處理器‧ 支援高達800MHz之系統匯流排(FSB)‧ 支援使用超執行緒(Hyper-Threading)技術之CPU

利用“超執行緒(HT)＂技術，可使作業系統在相當於裝上了兩具處理器的狀態下運作：利用一個＂實體＂處理器模擬出兩個獨立的＂邏輯＂處理器，同時執行兩個工作緒。

晶片組

‧ 配備高效能UMA North Bridge：內建Pentium 4 North Bridge，提供800 MHz 前端匯流排支援，並將UniChrome Pro 3D / 2D 繪圖&視訊控制器整合於單一晶片內

‧ 支援 Intel 800/533 MHz FSB Pentium 4 及 Pentium M 處理器，並支援超執行緒技術

‧ AGP v3.0 相容於支援快寫功能之8x/4x 傳輸模式‧ 支援2.5V SSTL-2 DRAM 介面之DDR400/333/266 記憶體‧ 支援66 MHz的 4X 及 8X 傳送模式，並支援 V-Link介面，提供

533 MB/秒的總頻寬‧ 相容於ACPI 2.0 及 PCI 匯流排電源管理 1.1規格‧ 繪圖引擎時脈高達133 MHz，不受記憶體時脈之限制

VIAP4M800 (NB)

VT8237 (SB) • PCI至系統記憶體的資料串流速度高達132Mbyte/秒 (資料經由高速V-Link介面傳送到北橋晶片。)

• PCI-2.2相容之 32位元3.3V PCI介面，輸入容限電壓5V• 支援3個PCI插槽，提供支援所有整合功能及LPC匯流排之仲裁

及解碼功能• 雙通道 SATA/RAID 控制器—相容於SATA 規格1.0版

‧ 2個 2.5V 184針DDR SDRAM DIMM記憶模組用插槽‧ 支援 DDR400/333/266 記憶體匯流排‧ 最大容量 2 GB

記憶體

擴充槽‧ 3個32位元 PCI 槽‧ 1個 8X AGP 槽‧ 1個 CNR 槽


繁體中文

內建區域網路 (選購)

‧ 採用單晶片100Base-TX/10Base-T 實體層解決方案‧ 採用100/10 Mbps雙速‧ 全 / 半雙工‧ 乙太網路控制器之MII介面 ‧ MII 介面，便於組態調整及顯示狀態‧ 自動省電模式‧ 自動協商功能：10 / 100、及全 / 半雙工‧ 符合所有適用之IEEE 802.3, 10Base-T 及100Base-Tx 規格‧ 晶片整波功能 – 無需外接的濾波器‧ 調適性等化器‧ 基線漂移修正功能‧ LED輸出

AC’97 音訊編解碼器‧ 相容於AC’97(2.3版) CODEC.‧ Front-Out、Surround-Out、MIC-In 及 Line-In 插頭感應功能‧ 3個具5位元音量控制功能之類比 line級立體聲輸入： LINE_IN、CD、及AUX‧ 2個類比line級單聲道輸入‧ 48針LQFP.‧ 內建耳機緩衝器及內部 PLL.

‧ 2個序列ATA連接器‧ 傳輸率超過現有頂級的 ATA (~150 MB/秒)，並且未來還可進一步提高‧ 主控端及裝置端之連接針的支數少

機載IDE通道‧ 支援PIO (可程式輸出入) 模式及DMA (直接記憶體存取)模式‧ 支援IDE Ultra DMA 匯流排主控功能，提供133/100/66 MB/秒傳輸率

序列ATA

機載輸出入埠‧ 2 個 PS/2 埠，供滑鼠與鍵盤使用‧ 1 個串列埠‧ 1 個平行埠‧ 1 個VGA埠‧ 4 個背板USB2.0 埠‧ 1 個區域網路埠(選購)‧ 麥克風音頻插座、線級輸入及線級輸出


繁體中文

BIOS 韌體本主機板使用AMI BIOS，使用者可以組態設定許多系統功能，包括如下：

• 電源管理• 喚醒警鈴• CPU參數• CPU及記憶體的時脈定時

此外，也可藉由參數的設定，調整處理器的時脈速度。

部份硬體規格和軟體內容可能會在未經通知的情況下更動，敬請見諒。


简体中文

P4M800 北桥 (NB) 和 VT8237 南桥 (SB) 芯片组是基于一种新型的、可扩展的架构，能提供已经证明的可靠性和高性能。

芯片组

• 高性能 UMA 北桥：在单个芯片中集成支持 800 MHz FSB 的

Pentium 4 北桥和 UniChrome 3D/2D 图形 & 视频控制器

• 支持 Intel 800/533 MHz FSB Pentium 4 和 Pentium M 处理

器及超线程技术

• 符合 AGP v3.0 标准，8x/4x 传输模式，支持快写

• 支持带 2.5V SSTL-2 DRAM 接口的 DDR400/333/266 内存

• 支持 66 MHz 4X 和 8X 传输模式，支持 V-Link 接口，总带

宽可达 533 MB/sec

• 符合 ACPI 2.0 和 PCI 总线电源管理 1.1 规格

• 由存储器时钟分离出的、最高 133 MHz 的图形引擎时钟

功能

处理器此主板使用 LGA775 型 Intel Pentium 4/Pentium D/Celeron D CPU，具备以下特点：

• 支持 Intel Pentium 4/Pentium D/Celeron D 处理器• 支持 800 MHz 系统总线 (FSB)• 支持“多线程”技术 CPU

“多线程”技术可以让操作系统认为自己连接了两个处理器，允许两个线程并行运行，每个线程位于同一处理器中的单独“逻辑”处理器中。

P4M800 (NB)

VT8237 (SB) • PCI 到系统内存数据传输速率可到 132 Mbyte/sec(数据通过高速 Ultra V-Link 接口发送到北桥）

• 符合 PCI-2.2 标准，带 5V 输入的 32 位 3.3V PCI 接口• 支持 3 个 PCI 插槽，用于所有整合功能和 LPC 总线的仲裁

和解码• 双通道串行 ATA/RAID 控制器—符合串行 ATA 规格 1.0

内存• 2 个用于 DDR SDRAM 内存条的 184-pin 2.5V DIMM 插槽• 支持 DDR 400/333/266 存储总线• 内存最多可达 2GB

• 3 个 32 位 PCI 插槽 • 1 个 8X AGP 插槽• 1 个通信网络转接 (CNR) 插槽

扩展槽


简体中文

AC’97 音频编解码器• 符合 AC’97(Rev 2.3) 的音频编解码器• 前置输出、环绕输出、麦克风输入和线入插孔检测 • 3 路带 5 位音量控制的模拟线路电平立体声输入：LINE_IN, CD, AUX• 2 路线路电平单声道输入• 48-Pin LQFP• 内置耳机缓冲和内部 PLL.

• 单芯片 100Base-TX/10Base-T 物理层解决方案• 双速-100/10 Mbps• 半双工和全双工• 以太网控制器的 MII 接口• 到配置&状态的 MII 接口• 自动节电模式• 自动协商：10/100，全双工/半双工• 符合所有相应的 IEEE 802.3、10Base-T 和 100Base-Tx 标准• 芯片波形成形 - 无需外部滤波器• 自适应均衡器• 基线游离校正• LED 输出

• 2 个用于连接鼠标和键盘的 PS/2 端口• 1 个串口• 1 个并口• 1 个VGA• 4 个后面板 USB2.0 端口• 1 个LAN (可选)• 麦克风、线入和线出声音插孔

集成 I/O端口

• 2 个Serial ATA 接口• 传输速率超过 ATA (~150 MB/s)，可扩展到更高速率• 主机和设备管脚数量少

Serial ATA

Onboard IDE 通道• 支持 PIO (程控输入/输出) 和 DMA (直接存储器存取) 模式• 支持 IDE Ultra DMA 总线控制，传输速率可达 133/100/66 MB/sec

快速以太网 LAN(可选)


简体中文

BIOS此主板使用 AMI BIOS，可以让用户自己配置以下系统功能：

• 电源管理• 唤醒报警• CPU 参数• CPU 和记忆定时

还可用于设置不同处理器时钟速度的参数。.

某些硬件规格和软件项目若有更改恕不另行通知。


Русский

Чипсеты P4M800 «Северный мост» (Northbridge, NB) и VT8237 «Южный мост» (Southbridge, SB) построены с использованием инновационной масштабируемой архитектуры, обеспечивающей высокую надежность и производительность.

Чипсет

• Скоростной северный мостик UMA: интегрированный северный мостик Pentium 4 с поддержкой 800 MHz FSB, графикой UniChrome Pro 3D / 2D и видео-контроллером в одном чипе

• Поддерживает процессоры Intel 800/533 MHz FSB Pen-tium 4 и Pentium M и технологию Hyper Threading

• AGP v3.0 совместимая с режимом передачи данных 8X/4X с поддержкой технологии Fast Write

• Поддержка памяти типа DDR400/333/266 с интерфейсом 2.5V SSTL-2 DRAM

• Поддерживает режимы передачи данных 66 MHz, 4X и 8X, интерфейс V-Link с общей скоростью передачи данных 533 MБ/сек

• Совместимость с управлением энергопотреблением ACPI 2.0 и PCI вер. 1.1

• Тактовая частота графического движка до 133 MГц, независимая от частоты памяти

ХарактеристикиПроцессорМатеринская плата использует процессоры Intel Pentium 4/Pentium D/CeleronD типа LGA775 и обладает следющими характеристиками:

• Размещает процессоры Intel Pentium 4/Pentium D/Celeron D• Поддерживает системные шины (FSB) с частотой 800MHz• Поддерживает технологию CPU “Hyper-Threading”

VIAP4M800 (NB)

VT8237 (SB)

Технология “Hyper-Threading” «убеждает» операционную систему в том, что в машине имеется два процессора; это позволяет параллельно обслуживать два процесса, причем каждый из процессов обслуживается отдельным «логическим» процессором в пределах одного физического процессора.

• Стриминг данных с шины PCI к системной памяти до 132 MБ/сек (пересылка данных к северному мостику по высокоскоростному интерфейсу Ultra V-Link)

• Совместимость с PCI-2.2, 32-битным интерфейсом 3.3V PCI, допустимый входной сигнал 5V

• Поддерживает три слота PCI с арбитражем и декодированием для всех интегрированных функций и шины LPC.

• Двухканальный контроллер Serial ATA/RAID, совместимый со спецификацией Serial ATA Rev. 1.0

Память• Два 184-штырьковых сокета 2.5V DIMM для модулей памяти DDR

SDRAM • Поддержка шины памяти DDR400/333/266• Максимальный объем памяти 2 Гб


Русский

• Одночипное решение физического слоя 100Base-TX/10Base-T• Двускоростная передача данных - 100/10 Mbps• половинный и полный дуплекс• Интерфейс MII для Еthernet-контроллера• Интерфейс MII для конфигурирования и определения статуса• Энергосберегающий режим.• Режим автовыбора: 10 / 100, полный / половинный дуплекс• Соответствует всем требованиям стандартов IEEE 802.3, 10Base-T и

100Base-Tx• Технология On Chip Wave Shaping – без потребности внешних

фильтров.

Интегрированные порты входа/выхода

Аудио КОДЕК AC’97• Совместимость с КОДЕКом AC’97(Rev 2.3).• Выходы/входы Front-Out, Surround-Out, MIC-In, Line-In с технологией

Jack Sensing• Три аналоговые линии стереовхода с 5-битовой регуляцией громкости:

LINE_IN,CD,AUX• Две аналоговые линии входа моно• 48-штырьковый LQFP.• Встроенный буфер наушников и внутренний PLL.

• Два коннектора Serial ATA• Скорость трансфера данных превышающая самые скоростные ATA

(~150 MБ/с) с возможностью дальнейшего повышения• Низко-пиновые интерфейсы хоста и устройств

• Поддержка режимов PIO (программируемый вход/выход) и DMA (Di-rect Memory Access)

• Поддержка захвата шины IDE Ultra DMA со скоростью трансфера данных 100/66/33 MБ/cек

Интегрированные каналы IDE

Serial ATA

• Два порта PS/2 для подключения мыши и клавиатуры• Один серийный порт• Один параллельный порт• Один порт VGA• Четыре порта USB 2.0 на тыльной панели• Один порт LAN (опционально)• Гнездо для подключения микрофона, гнезда аудио-входа и выхода

Встроенный сетевой адаптер LAN (опционально)

• Три 32-битных слота PCI • Один слот 8X AGP• Один слот CNR

Возможности расширения


Русский

BIOS Плата работает под AMI BIOS, который позволяет пользователю конфигурировать различные характеристики системы:

• Управление питанием• Сигналы пробуждения системы• Параметры CPU• Время доступа для CPU и памяти

BIOS допускает также установку параметров для различных частот процессора.

Некоторые параметры платы и характеристики ее программного обеспечения могут быть изменены без предварительного уведомления.

• Адаптивный эквалайзер.• Корректировка плавающей базовой линии• Выход LED


Polski

Mostek północny (NB) P4M800 i mostek południowy (SB) VT8237 chipsetu oparty jest na nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i funkcjonalnoœci.

Chipset

• Wysokowydajny mostek północny High Performance UMA: zintegrowany mostek północny Pentium 4 z obsługą 800 MHz FSB i procesorem grafiki i video UniChrome Pro 3D / 2D w jednym chipie

• Obsługuje procesory Intel Pentium 4 i Pentium M z FSB 800/533 MHz oraz technologię Hyper Threading

• AGP w wersji 3.0 zgodny ze standardem przesyłu 8X/4X zapewniający tryb Fast Write.

• Obsługuje pamięci DDR400/333/266 typu 2.5V SSTL-2 DRAM

• Obsługuje tryby przesyłania danych 66 MHz, 4X i 8X, kon-troler V-Link o szybkości 533 MB/sek.

• ACPI 2.0 zgodne z zarządzaniem energią szyny PCI wer. 1.1

• Zegar kontrolera graficznego do 133 MHz rozłączny z zegarem pamięci

CechyProcesorPłyta główna obsługuje procesory Intel Pentium 4/Pentium D/Celeron D typu LGA775 i posiada następujące właściwości:

• Przystosowana do obsługi procesorów Intel Pentium 4/Pentium D/Celeron D

• Obsługuje szynę systemowa (FSB) 800MHz• Zabezpiecza technologię CPU “Hyper-Threading”

VIA P4M800 (NB)

VT8237 (SB)

Technologia “Hyper-Threading” powoduje, że system "myśli”, że posiada dwa procesory i wykonuje równolegle dwa procesy; za wykonanie każdego procesu odpowiedzialny jest jeden z dwuch "logicznych" procesorów w ramach jednego fizycznego procesora

• Przesyłanie danych od PCI do pamięci o szybkości do 132 MB/sec (dane przesyłane są do mostka północnego z wysoką szybkością za pomocą kontrolera Ultra V-Link)

• 32-bitowy kontroler PCI 3.3V, tolerujący wejście 5V, zgodny ze specyfikacją PCI w wersji 2.2.

• Obsługuje 3 gniazda PCI z arbitrażem i dekodowaniem dla wszystkich funkcji oraz szynę LPC.

• Dwu kanałowy kontroler Serial ATA/RAID - zgodny ze specyfikacją Serial ATA w wersji 1.0.

Pamięć• Dwa 184 nóżkowe, 2.5V DIMM gniazda pamięci dla banków DDR SDRAM • Obsługuje szynę pamięci DDR400/333/266 • Maksymalnie można zainstalować do 2GB pamięci


Polski

• Jednochipowe rozwiązanie warstwy fizycznej 100Base-TX/10Base-T • Podwójna prędkość przesyłu 100/10 Mbps • Half i Full Duplex • Interfejs MII w kontrolerze ethernetu• Kontroler MII do konfiguracji i kontroli stanu.• System automatycznego oszczędzania energii.• Automatyczne wybieranie trybów 10/100, Full/Half Duplex• Zgodność ze wszystkimi standardami IEEE 802.3, 10Base-T i 100Base-Tx• Technologia “On Chip Wave Shaping” – bez potrzeby stosowania zewnętrznych

filtrów.• Adaptacyjny korektor poprzeczny • Korekcja poziomu linii bazowej • Wyjścia na świetlne diody sygnałowe LED.

• Trzy 32-bitowych gniazda zgodnych z PCI• Jedno gniazdo AGP 8X• Jedno gniazdo CNR

Możliwości rozbudowy

Gniazda We/Wy zintegrowane z płytą

Audio AC’97 CODEC

• Obsługuje tryby PIO (Programowalne Wejście/Wyjście) i DMA (Pamięć bezpośredniego dostępu)

• Obsługuje szynę IDE Ultra DMA z szybkościami przesyłu 133/100/66 MB/s

Wbudowane złącza IDE

Serial ATA• Dwa gniazda Serial ATA• Niezmiernie wysoka szybkość przesyłania (~150 MB/s) z możliwością jej

zwiększania• Mała liczba nóżek zarówno dla gniazda jak i dla stacji (urządzenia)

• Zgodne z AC’97 (w wersji 2.3) CODEC• Wyjścia Front i Surround, wejścia MIC-IN i LINE-IN rozpoznające wtyki. • Trzy analogowe linie wejściowe stereo z 5 bitową kontrolą głośności:

LINE_IN, CD, AUX.• Dwie analogowe linie wejściowe mono.• 48-nóżkowy LQFP• Wbudowany bufor słuchawkowy oraz wewnętrzny PLL.

• Dwa gniazda PS/2 dla myszy i klawiatury • Jedno gniazdo szeregowe • Jedno gniazdo równoległe • Jedno gniazdo VGA• Cztery gniazda USB 2.0 na tylnej ścianie• Jedno gniazdo LAN (opcjonalnie)• Gniazdo wejściowe mikrofonowe, gniazdo wejściowe i wyjściowe dzwięku

(audio)

Zintegrowana obsługa sieci LAN (opcjonalnie)


Polski

Firmowy BIOSPłyta głwna wyposażona jest w BIOS firmy AMI, który pozwala użytkownikowi konfigurować wiele cech systemu włączając w to następujące właściwości:

• Zarządzanie poborem mocy • Alarmy typu Wake-up • Parametry pracy procesora • Ustalenia szybkoœci pracy procesora i pamiêci

BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara procesora.

Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie bez uprzedniego powiadomienia.


Česky

Čipy northbridge (NB) P4M800 a southbridge (SB) VT8237 jsou založeny na inovativní a škálovatelné architektuře s ověřenou spolehlivostí a výkonností.

Čipová sada

• Vysoce výkonný řadič UMA North Bridge: Integratolvaný řadič North Bridge pro Pentium 4 s podporou 800 MHz FSB a video řadičem UniChrome Pro 3D / 2D v jediném čipu

• Podpora procesorů Intel 800/533 MHz FSB Pentium 4 a Pentium M a technologie Hyper Threading

• Splňuje specifikace standardu AGP v3.0 s přenosovou rychlostí 8X/4X s podporou rychlého zápisu

• Podpora typů paměti DDR400/333/266 s rozhraním 2,5 V SSTL-2 DRAM

• Podpora hostitelského rozhraní 66 MHz, přenosové režimy 8x/4x, rozhraní V-Link s celkovou šířkou pásma 533 GB/s

• Splňuje požadavky standardu ACPI 2.0 a PCI Bus Power Man-agement 1.1

• Taktování grafického jádra 133 MHz, nezávislé na taktování paměti

VlastnostiProcesorTato základní deska je určena pro procesory Intel Pentium 4/Pentium D/Celeron D LGA775 a může nabídnout následující vlastnosti:

• Použití pro procesory Intel Pentium 4/Pentium D/Celeron D s jádrem• Podporuje taktování systémové sběrnice (FSB) na frekvenci 800MHz• Podporuje technologii CPU „Hyper-Threading“

Technologie „Hyper-Threading“ umožňuje operačnímu systému pracovat tak, jako by byl připojen ke dvěma procesorům, protože je možné pracovat se dvěma toky programového kódu (vlákny) paralelně najednou, přičemž jsou k dispozici samostatné „logické“ procesory umístěné v rámci jednoho fyzického procesoru.

VIA P4M800 (NB)

VT8237(SB) • Přenos dat mezi sběrnicí PCI a systémovou paměti až 132 Mbps (data odesílaná ze severního můstku prostřednictvím vysokorychlostního rozhraní Ultra V-Link)

• Splňuje standard PCI -2,2, 32bitová sběrnice s napájením 3,3 V a s tolerancí vstupů 5 V

• Podpora tří slotů PCI pro rozhodování a dekódování pro všechny integrované funkce a sběrnici LPC.

• Dvoukanálový řadič Serial ATA/RAID - splňuje požadavky standardu Serial ATA verze 1.0

Paměť• Dvě patice 184kolíkové 2,5 V DIMM pro paměťové moduly DDR SDRAM • Podpora paměťové sběrnice DDR400/333/266• Maximální instalovaná paměť 2 GB

Rozšiřující sloty• Tři 32bitové patice PCI • Jeden slot 8X AGP• Jeden slot CNR


Česky

Vestavění síťové rozhraní LAN (volitelně)• Jeden čip fyzické síťové vrstvy 100Base-TX/10Base-T• Dvourychlostní 100/10 Mbps• Poloviční a Plný duplex• Rozhranní MII s řadičem Ethernet• Rozhraní MII pro konfiguraci a status• Automatický úsporný režim.• Automatické přepínání provozu: Provoz 10/100 Mb/s, plný/poloviční duplex• Splňuje všechny příslušné standardy IEEE 802.3, 10BASE-T a 100BASE-Tx• Tvarování vlny na čipu - nejsou vyžadovány žádné externí filtry.• Adaptivní ekvalizér.• Základní korekce kolísání.• Výstupy LED

I/O porty na desce

Zvukový kodek AC’97• Splňuje požadavky kodeku standardu AC’97, verze 2.3• Přední výstup, výstup prostorového zvuku, vstup mikrofonu a linkový vstup• Tři analogové linkové stereo vstupy s 5bitovým ovládáním hlasitosti LINE_IN,

CD, AUX• Dva analogové linkové mono vstupy• 48kolíkové LQFP.• Vestavěná vyrovnávací paměť sluchátek a vnitřní PLL.

Integrované kanály IDE• Podpora režimů PIO (programovatelný vstup/výstup) a DMA (přímý přístup

do paměti)• Podpora řízení sběrnice IDE Ultra DMA s přenosovými rychlostmi

133/100/66 MB/s

Serial ATA• Dva konektory Serial ATA• Přenosové rychlosti přesahující specifikace ATA (asi 150 MB/s) se

škálovatelností na vyšší hodnoty• Nízký počet kolíků hostitelského rozhraní i zařízení

• Dva porty PS/2 pro myš a klávesnici• Jeden sériový port• Jeden paralelní port• Jeden port VGA • Čtyři portu USB 2.0 na zadním panelu• Jeden port LAN (volitelně) • Zvukové konektory pro mikrofon, zvukový vstup a výstup


Česky

Firmware BIOSZákladní deska využívá BIOS formy AMI, který uživateli umožňuje nakonfigurovat mnoho systémových parametrů, včetně následujících:

• Řízení spotřeby• Alarmy při spouštění systému• Parametry CPU • Časování CPU a paměti

Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence procesoru.

Některé technické parametry hardware a software se mohou měnit bez předchozího upozornění.


Română

Seturile de chipuri P4M800 Northbridge (NB) şi VT8237 Southbridge (SB) se bazează pe o arhitectură inovatoare şi scalabilă, care s-a impus deja prin fiabilitate şi performanţă.

Setul de chipuri

• Dispozitiv de interconectare de înaltă performantă High Perfor-mance UMA North Bridge: Pentium 4 North Bridge integrat com-patibil cu 800 MHz FSB şi controler grafică si video UniChrome Pro 3D / 2D într-un cip

• compatibil cu procesoare Intel 800/533 MHz FSB Pentium 4 şi Pentium M şi Tehnologie Hyper Threading

• Compatibilă cu AGP, versiunea 3.0, cu moduri de transfer 8x/4x şi suport Fast Write (operaţie de scriere rapidă)

• Compatibil cu tipuri de memorie DDR400/333/266 cu interfaţă 2.5V SSTL-2 DRAM

• compatibil cu moduri de transfer 66 MHz, 4X şi 8X, interfaţă V-Link cu lăţime de bandă totală de 533 MB/sec

• Compatibil cu sisteme de gestiune a energiei busului ACPI 2.0 şi PCI Bus Power Management 1.1

• motorul de grafică se sincronizează până la 133 MHz decuplat de temporizatorul memoriei

CaracteristiciProcesorulPlaca de bază utilizează Intel Pentium 4/Pentium D/Celeron D tip LGA775 care are următoarele caracteristici:

• Funcţionează cu procesoare Intel Pentium 4/Pentium D/Celeron D• Funcţionează cu bus sistem (FSB) de 800 MHz• Este compatibilă cu unităţi centrale dotate cu tehnologia „Hyper-

Threading”

VIA P4M800 (NB)

VT8237 (SB)

Tehnologia „Hyper-Threading” permite sistemului de operare să funcţioneze ca şi cum ar exista două procesoare, putând fi rulate în paralel două fire, fiecare pe câte un procesor „logic” separat, aflate pe acelaşi procesor fizic.

• flux date PCI la sistem de până la 132Mbyte/sec (date trimise la north bridge prin interfaţă Ultra V-Link de mare viteză)

• compatibil cu interfaţă PCI-2.2, 32-bit 3.3V PCI cu input suport 5V

• compatibil cu trei sloturi PCI de arbitrare şi decodare pentru toate funcţiunile integrate şi bus LPC.

• Dual Channel Serial ATA/RAID Controller— compatibil cu Serial ATA cu Serial ATA Specification Revision 1.0

Memoria• Două socketuri DIMM 184-pin 2.5V pentru modul de memorie DDR

SDRAM • Compatibil cu memorie bus DDR400/333/266• Memoria maximă instalată este de 2 Gb


Română

• Soluţie cu start fizic cu un singur cip 100Base-TX/10Base-T physical layer solution

• Viteză duală 100/10 Mbps• Half şi Full Duplex• Interfaţă MII pentru controler ethernet• interfaţă MII la Configuraţie & Status• Mod de economisire energie automat• negociere automată: 10 / 100, Full / Half Duplex• Corespunde tuturor standardelor IEEE 802.3, 10Base-T and 100Base-Tx• Fasonare undă On Chip – nu sunt necesare filtre externe.• egalizator adaptiv• Corectare Deviere de la punct plecare• Ieşiri LED

Porturi I/O Onboard

Codec Audio AC’97• compatibil cu CODEC AC’97(Rev 2.3)• Ieşire-Faţă, Ieşire Surround, Intrare MIC şi senzor jack Line-in• trei intrări stereo analoage line-level cu control volum de 5-bit: LINE_IN, CD,

AUX• două intrări mono analoage line-level• LQFP cu 48 ace de conectare• tampon căşti încorporate şi PLL intern

• Trei sloturi de 32 biţi compatibile PCI• un slot 8X AGP• un slot CNR

• Compatibil cu modurile PIO (Programmable Input/Output – Input/Output programabil) şi DMA (Direct Memory Access – Acces Memorie Direct)

• Compatibil cu IDE Ultra DMA bus mastering cu rata de transfer de of 100/66/33 MB/sec

Canale IDE Onboard

• două conectoare Serial ATA• Rata de transfer depăşind cel mai bun ATA (~150 MB/s) cu reglabilitate la

rate mai mari• Numărătoare Low pin pentru host si pentru dispozitive

Serial ATA

Sloturi de expansiune

• Două porturi PS/2, pentru mouse şi tastatură• Un port serial• Un port paralel• Un port VGA• Patru porturi USB2.0 pe panoul din spate• Un port LAN (opţional)• Mufe audio pentru microfon, intrare şi ieşire audio

Fast Ethernet LAN (opţional)


Română

Firmware BIOS Placa de bază utilizează AMI BIOS, care permite utilizatorului să configureze mai mulţi parametri ai sistemului, cum ar fi:

• Gestionarea energiei• Alarme de trezire• Parametri CPU• Temporizare CPU şi memorie

Acest firmware poate fi utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă ale procesorului.

Anumite specificaţii hardware şi elemente de software pot fi modificate fără înştiinţare prealabilă.


Български

Чипсетът със северен мост VIA P4M800 (NB) и южен мост VT8237 (SB) е изграден на базата на оригинална архитектура с възможност за надстройка с доказана надеждност и производителност.

Памет

Чипсет

• Високопроизводителен UMA северен мост с поддръжка на процесори Pentium 4, процесорна шина 800 MHz и UniChrome Pro 3D / 2D Графични и Видео контролери на един чип.

• Поддръжка на процесори Intel Pentium 4 и Pentium M с процесорна шина 800/533 MHz и технология Hyper Threading

• Контролер AGP v3.0 съвместим с трансфер 8X/4X с поддръжка на Fast Write

• поддръжка на модули памет DDR400/333/266 с интерфейс 2.5V SSTL-2 DRAM

• Поддръжка на скорости на трансфер 66 MHz, 4X и 8X, V-Link интерфейс с обща честотна лента 533 MB/sec

• Съвместимост със спецификациите ACPI 2.0 и PCI Bus Power Management 1.1

• Графично ядро със скорост до 133 MHz отделна от скоростта на паметта

СпецификацияПроцесорТази дънна платка използва сокет LGA775 за Intel Pentium 4/Pentium D/Celeron D със следните спецификации:

• поддръжка на процесори Intel Pentium 4/Pentium D/Celeron D• поддръжка на системна шина със скорост 800MHz• поддръжка на процесори с технология “Hyper-Threading"

Технологията “Hyper-Threading" позволява да се “излъже” операционната система, че работи на два процесора, което дава възможност за паралелното изпълнение на две задачи на два отделни “логически” процесора в един и същ физически процесор.

VIA P4M800 (NB)

VT8237 (SB)

• Две гнезда 184-pin 2.5V DIMM за модули памет DDR SDRAM Графика• Поддръжка на шина за памет DDR400/333/266• Общ максимален капацитет 2 GB

• Скорост на обмен между PCI и системната памет до 132Mbyte/sec (данните се изпращат до северния мост чрез високоскоростния Ultra V-Link интерфейс)

• съвместимост с PCI-2.2, 32-битов 3.3V PCI интерфейс с толеранс 5V

• Три PCI слота за арбитраж и декодиране на всички интегрирани функции и LPC шината.

• Двуканален Serial ATA/RAID контролер – съвместим със спецификациите Serial ATA Revision 1.0

• три слота 32-bit PCI • Един слот AGP 8X• Един слот CNR

Разширителни слотове


Български

AC’97 аудио кодек• съвместим със спецификацията AC’97(Rev 2.3).• разпознаване на изходите Front-Out, Surround-Out, MIC-In и Line-In • Три аналогови линейни стерео входа с 5-битов контрол на силата на звука:

LINE_IN,CD,AUX• Два аналогови линейни моно входа• 48-pins LQFP.• Вграден буфер за слушалки и вътрешен PLL.

Интегрирани IDE канала• Поддръжка на режими PIO (Programmable Input/Output) и DMA (Direct

Memory Access)• Поддръжка на IDE Ultra DMA със скорост на трансфер 100/66/33 MB/sec

Serial ATA• Два Serial ATA конектора• Скорост на трансфер по-голяма от най-добрата при ATA (~150 MB/s) с

възможност за увеличение до по-високи скорости• Шина Low pin count за контролера и устройствата

Вградени I/O портове• два PS/2 порта за мишка и клавиатура• един сериен порт• един паралелен порт• един VGA порт• един LAN порт (опция)• Четири порта USB2.0 на задния панел• Аудио жакове за микрофон, линеен вход и линеен изход

Мрежов контролер Fast Ethernet (опция)• Интегриран едночипов LAN контролер на физическо ниво за Ethernet

100Base-TX/10Base-T• Поддръжка на режими 100/10 Mbps• Half / Full Duplex• Интерфейс MII към ethernet контролера• MII интерфейс към настройки и статус (Configuration & Status)• Автоматичен режим за намалено потребление на енергия.• Автоматично съгласуване: 10 / 100, Full / Half Duplex• Съвместимост с всички приложими стандарти IEEE 802.3, 10Base-T и

100Base-Tx• Вградено формиране на импулсите (Wave Shaping) – без нужда от

външни филтри.• Адаптивен еквалайзер.• Baseline wander Correction.• LED изходи


Български

BIOS FirmwareДънната платка използва AMI BIOS с възможност за различни системни настройки, включително

• управление на захранването• Wake-up аларми• параметри на процесора• синхронизиране на процесора и паметта

настройка на скоростта на часовника на процесора

Хардуерните и софтуерни спецификации и параметри могат да бъдат изменени без предупреждение.


Magyar

A P4M800 Northbridge (NB) és VT8237 Southbridge (SB) lapkakészletek egy új és méretezhető, nagy megbízhatóságú és teljesítőképességű architektúrára épülnek.

Lapkakészlet

• nagy teljesítményű UMA North Bridge híd: integrált Pentium 4 North Bridge 800 MHz FSB biztosítással és UniChrome Pro 3D / 2D egy chipes grafika és video vezérlővel

• megfelel Intel 800/533 MHz FSB Pentium 4 és Pentium M pro-cesszoroknak és Hyper Threading Technológiának

• Az AGP 3.0 változata, amely a 8-szoros/4-szeres átvitellel és Fast Write (gyors írás) művelettel kompatibilis

• Kompatibilis DDR400/333/266 memória típusokkal 2.5V SSTL-2 DRAM interfésszel

• megfelel 66 MHz, 4X és 8X átvitel módnak, V-Link interfésznek 533MB/s teljes sávszélességggel

• kompatibilis ACPI 2.0 és PCI Bus Power Management 1.1 busz áramszabályozóval

• a grafikai motor elér egészen 133 MHz sebességig a memória óráról lekapcsolva

JellemzőProcesszorAz alaplap LGA755 típusú Intel Pentium 4/Pentium D/Celeront D használ, amely a következő tulajdonságokkal rendelkezik:

• Intel Pentium 4/Pentium D/Celeron D processzorokkal működik• 800 MHz sebességű rendszerbuszt (FSB) támogat• Támogatja a „Hyper-Threading” technológiát használó központi

egységeketA „Hyper-Threading” technológia által az operációs rendszer úgy működik, mintha két processzorral rendelkezne, ami két szál párhuzamos futását teszi lehetővé két független, ugyanazon fizikai processzoron található „logikai” processzoron.

VIAP4M800 (NB)

VT8237 (SB) • PCI-rendszer adatáramlás egészen 132MB/sec sebességig (north bridge-hez küldött adatok nagy sebességű Ultra V-Link interfészen keresztül)

• kompatibilis PCI-2.2, 32-bit 3.3V PCI interfésszel 5V toleráns bemenettel

• megfelel három PCI kiválasztó és dekódoló nyílásnak az összes integrált funkcióhoz és LPC buszhoz.

• kétcsatornás Serial ATA/RAID vezérlő — kompatibilis Serial ATA Specification Revision 1.0- val

Memória• Két 184-pin 2.5V DIMM foglalalt DDR SDRAM memória modulokhoz • Kompatibilis DDR400/333/266 memóriabusszal• Maximális telepített memória 2GB

• Három 32 bites PCI foglalat• egy 8X AGP nyílás• egy CNR nyílás

Expanziós nyílások


Magyar

Gyors Ethernet LAN (opcionális)• Egylapkás 100Base-TX/10Base-T fizikai réteges megoldás• Duál sebességű 100/10 Mbps• Half /Full Duplex• MII interfész ethernet vezérlőnek• MII Interfész a Konfiguráció & Állapothoz• automatikus energiagazdálkodási mód.• automatikus egyeztetés: 10 / 100, Full / Half Duplex• Megfelel az összes vonatkozó IEEE 802.3, 10Base-T és 100Base-Tx szab-

ványnak • On Chip hullámformálás – nem szükséges külső szűrő.• Adaptív Equalizer.• Nullapont eltérés igazítás.• LED kimenetek

AC’97 Audio Codec• kompatibilis AC’97(Rev 2.3) CODEC-kel• Első-kimenet, környezeti-kimenet, MIC bemenet és Line-in jack érzékelés• három analóg line-level sztereo bemenet 5-bit hangerősség vezérléssel:

LINE_IN, CD, AUX• két analóg line-level mono bemenet• 48-tűs LQFP.• beépített fülhallgató puffer és belső PLL.

• Kompatibilis PIO (Programmable Input/Output – programozható bemenet/kimenet) és DMA (Direct Memory Access – közvetlen memória hozzá-férés) módokkal

• Kompatibilis IDE Ultra DMA busz vezérléssel, 100/66/33 MB/sec átviteli sebességgel

Onboard IDE csatornák

• két sorozatos ATA csatlakozó• Átviteli sbesség meghaladja a legjobb ATA (~150 MB/s) sebességet,

felgyrsítható nagyobb sebességre• Alacsony pin számlálás mind a host, mind a berendezések esetén

Sorozatos ATA

Onboard I/O portok• Két PS/2 port az egér és a billentyűzet számára• Egy soros port• Egy párhuzamos port• Egy VGA port• Négy hátsó panel USB2.0 port• Egy LAN port (választható)• Audio csatlakozók mikrofon, bemenet és kimenet számára


Magyar

BIOS FirmwareAz alaplapon levő AMI BIOS segítségével a felhasználó a rendszer sok paraméterét állíthatja be, például:

• Energiagazdálkodás• Ébresztési riasztások• CPU paraméterek• CPU és memória időzítés

A firmware segítségével a processzor órajel-frekvenciáinak paramétereit is beállíthatják.

Bizonyos hardverjellemzők és szoftverelemek előzetes bejelentés nélkül módosulhatnak.

P4M800-M7v31 motherboad

Documents

Transcript of P4M800-M7v31 motherboad