P-61A with gun turret S.A. 49 609 - Eduard
Transcript of P-61A with gun turret S.A. 49 609 - Eduard
P-61A with gun turret S.A.49 6091/48 scale detail set for GREAT WALL HOBBY kit L-4806 • sada detailů pro model 1/48 GREAT WALL HOBBY L-4806
ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PŘED SLEPENÍM
1/6 49 609
ball penA1
9pcs
F23
F23
A1
632
14
19 20
36
47
48
101
73
89
70
105
105
G5
2/6 49 609
A116
86
34
13
9
F55
26
15
A1
34
29
30
4
3
G5 F30
7
24
45
31
25
23
27
51
I3
52
5251
88 108106
3/6 49 609
F6
F52
F11
21
22
42
43
14
35
38
A2
9pcs
69
F34
A2
F11
103
6766
65
58
57
59
78
74
102
64
56
81
80
84
104
83
96
95
98
4/6 49 609
F30
41
44
37
28
40
A2
A2
A2
71 72
92
99
75
94
91
97
90
93
109 110
114 113
plastic
112
111
1,2x8,0mm
5/6 49 609
1
11
2
33
10
12
17
18
F12, F13, F59, F62
2 sets
F53
5
F17
39
8
F17
107
79
I12, I13, I15, I17, I18
53
53
63
60
61
62
49
54
33
55
50
© EDUARD M.A. 2012 Made in Czech Republicwww.eduard.com
6/6 49 609
J3 J1
J5
J5
76
85
100
77
87
68
82
46
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem přilepíte, při pokusu o odlepení dojde k poškození dílu.
1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovém papíře. Po oddělení je sejměte z krycího papíru.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na části dílů, na kterých je naneseno lepidlo.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za části, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will be permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte přesnou pozici a přimáčkněte. Díl dokonale přilne až po přimáčknutí, před přimáčknutím lze dílem opatrně manipulovat.
PARTS WITH GLUE DÍLY OPATŘENÉ LEPIDLEM