OWNER’S MANUAL - · PDF fileImportant manual information EMU31283 To the owner Thank you...
Transcript of OWNER’S MANUAL - · PDF fileImportant manual information EMU31283 To the owner Thank you...
VZ200RVZ225HVZ250FVZ300B
OWNER’S MANUAL
6C9-28199-18
U.S.A.EditionLIT-18626-08-44
6C9-9-18 Hyoshi 09.3.31 3:28 PM ページ 1
EMU25073
ZMU01690
Read this manual carefully before operating this outboard motor. Keep this manualonboard in a waterproof bag when boating. This manual should stay with the outboardmotor if it is sold.
6C9-9-18 Hyoshi 09.3.31 3:28 PM ページ 2
Important manual information
EMU31283
To the owner
Thank you for choosing a Yamaha outboardmotor. This Owner’s Manual contains infor-mation needed for proper operation, mainte-nance and care. A thorough understandingof these simple instructions will help you ob-tain maximum enjoyment from your newYamaha. If you have any question about theoperation or maintenance of your outboardmotor, please consult a Yamaha dealer.In this Owner’s Manual particularly importantinformation is distinguished in the followingways.
: This is the safety alert symbol. It isused to alert you to potential personal injuryhazards. Obey all safety messages that fol-low this symbol to avoid possible injury ordeath.
WARNING
EWM00781
A WARNING indicates a hazardous situa-tion which, if not avoided, could result in
death or serious injury.
NOTICE
ECM00701
A NOTICE indicates special precautionsthat must be taken to avoid damage to the
outboard motor or other property.
TIP:
A TIP provides key information to make pro-cedures easier or clearer.
Yamaha continually seeks advancements inproduct design and quality. Therefore, whilethis manual contains the most current prod-uct information available at the time of print-ing, there may be minor discrepanciesbetween your machine and this manual. If
there is any question concerning this manu-al, please consult your Yamaha dealer.
TIP:
The VZ200RTR, VZ225HTR, VZ250FTR,VZ300BTR and the standard accessoriesare used as a base for the explanations andillustrations in this manual. Therefore someitems may not apply to every model.
EMU25111
VZ200R, VZ225H, VZ250F, VZ300BOWNER’S MANUAL
©2009 by Yamaha Motor Corporation, USA1st edition, April 2009
All rights reserved.Any reprinting or unauthorized usewithout the written permission ofYamaha Motor Corporation, USA
is expressly prohibited.Printed in Japan
P/N LIT-18626-08-44
Table of contents
Safety information............................. 1
Outboard motor safety .................... 1
Propeller............................................ 1Rotating parts.................................... 1Hot parts ........................................... 1Electric shock.................................... 1Power trim and tilt ............................. 1Engine shut-off cord (lanyard)........... 1Gasoline............................................ 1Gasoline exposure and spills ............ 2Carbon monoxide.............................. 2Modifications ..................................... 2
Boating safety ................................. 2
Alcohol and drugs ............................. 2Personal flotation devices ................. 2People in the water ........................... 2Passengers ....................................... 2Overloading....................................... 2Avoid collisions ................................. 3Weather ............................................ 3Accident reporting ............................. 3Boat education and training .............. 3Passenger training ............................ 4Boating safety publications ............... 4Laws and regulations ........................ 4
Boating organizations...................... 4Basic boating rules (Rules of the
road) .............................................. 4
Steering and sailing rules and sound signals.................................. 5
Rules when encountering vessels .... 5Other special situations..................... 6
General information .......................... 9
Identification numbers record.......... 9
Outboard motor serial number .......... 9Key number....................................... 9
Read manuals and labels.............. 10
Warning labels ................................ 10
Specifications and requirements...13
Specifications ................................ 13Installation requirements ............... 14
Boat horsepower rating................... 14Mounting motor ............................... 14
Remote control requirements........ 14Battery requirements..................... 14
Specifications of Battery..................14Mounting battery .............................15Multiple batteries .............................15
Propeller selection ........................ 15Start-in-gear protection ................. 15Engine oil requirements ................ 16Fuel requirements ......................... 16
Gasoline ..........................................16Ring Free Fuel Additive...................17
Muddy or acidic water ................... 17Anti-fouling paint ........................... 17Motor disposal requirements......... 17Emergency equipment .................. 17Emission control information......... 17
North American models...................17Star labels .......................................18
Components .................................... 20
Components diagram.................... 20
Remote control box .........................21Remote control lever .......................22Neutral interlock trigger ...................22Neutral throttle lever ........................22Throttle friction adjuster...................22Engine shut-off cord (lanyard) and
clip.................................................23Main switch .....................................23Power trim and tilt switch on remote
control ...........................................24Power trim and tilt switch on bottom
engine cowling ..............................24Trim tab with anode.........................24Tilt support lever for power trim and
tilt model........................................25Cowling lock levers .........................25Flushing device ...............................26Fuel filter/Water separator...............26
Instruments and indicators............ 28
Digital tachometer ......................... 28
Tachometer .....................................28Trim meter .......................................28Hour meter ......................................28Oil level indicator (digital type) ........29Overheat-alert indicator...................29
Digital speedometer ...................... 29
Speedometer...................................29
Table of contents
Fuel gauge ...................................... 30Trip meter / Clock / Voltmeter ......... 30Fuel level-alert indicator .................. 31Low battery voltage-alert
indicator ........................................ 31
Analog tachometer ........................ 31
Oil level indicators (three indicators) ..................................... 31
Analog trim meter.......................... 32Command link multifunction
meters ......................................... 32Command link multifunction
tachometers ................................ 32
Start-up checks ............................... 33Oil level alert ................................... 33Overheat alert ................................. 34Water separator alert ...................... 34Engine trouble alert ......................... 35Low battery voltage-alert................. 35
Command link multifunction speed & fuel meters ............................... 36
Command link multifunction speedometers ............................. 37
Command link multifunction fuel management meters ................... 38
Engine control system.................... 39
Alert system .................................. 39
Overheat alert ................................. 39Oil level alert and oil filter clogging
alert............................................... 39
Installation ....................................... 41
Installation ..................................... 41
Mounting the outboard motor .......... 41
Operation ......................................... 43
First-time operation ....................... 43
Breaking in engine .......................... 43Getting to know your boat ............... 43
Checks before starting engine ...... 43
Fuel level......................................... 43Remove cowling.............................. 43Fuel system..................................... 44Controls........................................... 44Engine shut-off cord (lanyard)......... 44Oil.................................................... 45Engine............................................. 45
Operation after a long period of storage ..........................................45
Flushing device ...............................46Install cowling..................................46Checking power trim and tilt
system...........................................47Battery.............................................48
Filling fuel and engine oil .............. 48
Filling fuel for models without a fuel joint.........................................48
Filling oil for oil injection models......49Oil level indicator operation.............50
Operating engine .......................... 51
Sending fuel ....................................51Starting engine ................................51
Checks after starting engine ......... 52
Cooling water ..................................52
Warming up engine....................... 53
Electric start and prime start models ..........................................53
Checks after engine warm-up....... 53
Shifting ............................................53Stop switches ..................................53
Shifting.......................................... 53Stopping boat................................ 54Stopping engine............................ 54
Procedure........................................55
Trimming outboard motor.............. 55
Adjusting trim angle (Power trim and tilt) ..........................................55
Adjusting boat trim ..........................56
Tilting up and down....................... 57
Procedure for tilting up (power trim and tilt models)..............................57
Procedure for tilting down (power trim and tilt models).......................58
Shallow water................................ 59
Power trim and tilt models...............59
Cruising in other conditions........... 60
Maintenance .................................... 61
Transporting and storing outboard motor ........................................... 61
Storing outboard motor ...................61Procedure........................................61Lubrication (oil injection models) .....62
Table of contents
Cleaning and anticorrosion measures ...................................... 62
Flushing power unit ......................... 62Cleaning the outboard motor .......... 63Checking painted surface of
motor............................................. 63
Periodic maintenance.................... 63
Replacement parts .......................... 64Maintenance interval guidelines...... 64Maintenance chart 1 ....................... 65Maintenance chart 2 ....................... 67Greasing ......................................... 68Cleaning and adjusting spark
plug ............................................... 68Inspecting idling speed ................... 69Checking water in engine oil tank ... 70Checking wiring and connectors ..... 70Checking propeller .......................... 70Removing propeller ......................... 71Installing propeller ........................... 71Changing gear oil ............................ 72Inspecting and replacing
anode(s)........................................ 73Checking battery (for electric start
models) ......................................... 74Connecting the battery .................... 74Disconnecting the battery ............... 75
Trouble Recovery............................ 76
Troubleshooting ............................ 76Temporary action in emergency.... 79
Impact damage ............................... 79Replacing fuse ................................ 79Power trim and tilt will not
operate.......................................... 80Water separator-alert indicator
blinks while cruising ...................... 80
Engine fails to operate .................. 82
Low oil level alert activates ............. 82
Treatment of submerged motor..... 83
Consumer information.................... 84
YAMAHA MOTOR CORPORATION, U.S.A. V MAX SERIES 2 TWO-STROKE OUTBOARD MOTOR THREE YEAR LIMITED
WARRANTY ............................... 84IMPORTANT WARRANTY
INFORMATION IF YOU USE YOUR YAMAHA OUTSIDE THE USA OR CANADA ...................... 87
1
Safety information
EMU33622
Outboard motor safety
Observe these precautions at all times.
EMU36501
Propeller
People can be injured or killed if they comein contact with the propeller. The propellercan keep moving even when the motor is inneutral, and sharp edges of the propeller cancut even when stationary.
�
Stop the engine when a person is in thewater near you.
�
Keep people out of reach of the propeller,even when the engine is off.
EMU33630
Rotating parts
Hands, feet, hair, jewelry, clothing, PFDstraps, etc. can become entangled with inter-nal rotating parts of the engine, resulting inserious injury or death.Keep the top cowling in place whenever pos-sible. Do not remove or replace the cowlingwith the engine running.Only operate the engine with the cowling re-moved according to the specific instructionsin the manual. Keep hands, feet, hair, jewel-ry, clothing, PFD straps, etc. away from anyexposed moving parts.
EMU33640
Hot parts
During and after operation, engine parts arehot enough to cause burns. Avoid touchingany parts under the top cowling until the en-gine has cooled.
EMU33650
Electric shock
Do not touch any electrical parts while start-ing or operating the engine. They can causeshock or electrocution.
EMU33660
Power trim and tilt
Body parts can be crushed between the mo-
tor and the clamp bracket when the motor istrimmed or tilted. Keep body parts out of thisarea at all times. Be sure no one is in thisarea before operating the power trim and tiltmechanism.The power trim and tilt switches operateeven when the main switch is off. Keep peo-ple be away from the switches wheneverworking around the motor.Never get under the lower unit while it is tilt-ed, even when the tilt support lever is locked.Severe injury could occur if the outboard mo-tor accidentally falls.
EMU33671
Engine shut-off cord (lanyard)
Attach the engine shut-off cord so that theengine stops if the operator falls overboardor leaves the helm. This prevents the boatfrom running away under power and leavingpeople stranded, or running over people orobjects.Always attach the engine shut-off cord to asecure place on your clothing or your arm orleg while operating. Do not remove it to leavethe helm while the boat is moving. Do not at-tach the cord to clothing that could tearloose, or route the cord where it could be-come entangled, preventing it from function-ing.Do not route the cord where it is likely to beaccidentally pulled out. If the cord is pulledduring operation, the engine will shut off andyou will lose most steering control. The boatcould slow rapidly, throwing people and ob-jects forward.
EMU33810
Gasoline
Gasoline and its vapors are highly flam-mable and explosive.
Always, refuel ac-cording to the procedure on page 51 toreduce the risk of fire and explosion.
Safety information
2
EMU33820
Gasoline exposure and spills
Take care not to spill gasoline. If gasolinespills, wipe it up immediately with dry rags.Dispose of rags properly.If any gasoline spills onto your skin, immedi-ately wash with soap and water. Changeclothing if gasoline spills on it.If you swallow gasoline, inhale a lot of gaso-line vapor, or get gasoline in your eyes, getimmediate medical attention. Never siphonfuel by mouth.
EMU33900
Carbon monoxide
This product emits exhaust gases whichcontain carbon monoxide, a colorless, odor-less gas which may cause brain damage ordeath when inhaled. Symptoms include nau-sea, dizziness, and drowsiness. Keep cock-pit and cabin areas well ventilated. Avoidblocking exhaust outlets.
EMU33780
Modifications
Do not attempt to modify this outboard mo-tor. Modifications to your outboard motormay reduce safety and reliability, and renderthe outboard unsafe or illegal to use.
EMU33740
Boating safety
This section includes a few of the many im-portant safety precautions that you shouldfollow when boating.
EMU33710
Alcohol and drugs
Never operate after drinking alcohol or tak-ing drugs. Intoxication is one of the mostcommon factors contributing to boating fatal-ities.
EMU33720
Personal flotation devices
Have an approved personal flotation device(PFD) on board for every occupant. Yamaha
recommends that you must wear a PFDwhenever boating. At a minimum, childrenand non-swimmers should always wearPFDs, and everyone should wear PFDswhen there are potentially hazardous boat-ing conditions.
EMU33731
People in the water
Always watch carefully for people in the wa-ter, such as swimmers, skiers, or divers,whenever the engine is running. Whensomeone is in the water near the boat, shiftinto neutral and stop the engine.Stay away from swimming areas. Swimmerscan be hard to see.The propeller can keep moving even whenthe motor is in neutral. Stop the engine whena person is in the water near you.
EMU33751
Passengers
Consult your boat manufacturer’s instruc-tions for details about appropriate passengerlocations in your boat and be sure all pas-sengers are positioned properly before ac-celerating and when operating above an idlespeed. Standing or sitting in non-designatedlocations may result in being thrown eitheroverboard or within the boat due to waves,wakes, or sudden changes in speed or direc-tion. Even when people are positioned prop-erly, alert your passengers if you must makeany unusual maneuver. Always avoid jump-ing waves or wakes.
EMU33760
Overloading
Do not overload the boat. Consult the boatcapacity plate or boat manufacturer for max-imum weight and number of passengers. Besure that weight is properly distributed ac-cording to the boat manufacturers instruc-tions. Overloading or incorrect weightdistribution can compromise the boats han-
Safety information
3
dling and lead to an accident, capsizing orswamping.
EMU33772
Avoid collisions
Scan constantly for people, objects, and oth-er boats. Be alert for conditions that limit yourvisibility or block your vision of others.
Operate defensively at safe speeds andkeep a safe distance away from people, ob-jects, and other boats.
�
Do not follow directly behind other boats orwaterskiers.
�
Avoid sharp turns or other maneuvers thatmake it hard for others to avoid you or un-derstand where you are going.
�
Avoid areas with submerged objects orshallow water.
�
Ride within your limits and avoid aggres-sive maneuvers to reduce the risk of lossof control, ejection, and collision.
�
Take early action to avoid collisions. Re-member, boats do not have brakes, andstopping the engine or reducing throttlecan reduce the ability to steer. If you arenot sure that you can stop in time beforehitting an obstacle, apply throttle and turnin another direction.
EMU33790
Weather
Stay informed about the weather. Checkweather forecasts before boating. Avoid
boating in hazardous weather.
EMU33800
Accident reporting
Boat operators are required by law to file aBoating Accident Report with their stateboating law enforcement agency if their boatis involved in any of the following accidents:1. There is loss of life or probable loss of
life.2. There is personal injury that requires
medical attention beyond first aid.3. There is property damage to boats or
other property over a certain amount.4. There is complete loss of a boat.Contact local law enforcement personnel if areport is necessary.
EMU33870
Boat education and training
Operators should take a boating safetycourse. This may be required in your state.Many of the organizations listed in the nextsection can provide information about cours-es in your area.You may also want to consider an Internet-based program for basic boater education.The Online Boating Safety Course providedby the BoatU.S. Foundation, is approved bythe National Association of State BoatingLaw Administrators (NASBLA) and recog-nized by the United States Coast Guard.Most, but not all, states accept this course tomeet their minimum requirements. While itcannot replace an in-depth course such asone offered by the U.S. Coast Guard, U.S.Power Squadron, or other organization, thisonline course does provide a general over-view of the basics in boating safety, require-ments, navigation, and operation. Uponsuccessful completion of the course, theuser can download a certificate of comple-tion immediately or, for a small charge, re-quest one by mail. To take this free course,
ZMU06025
Safety information
4
go to boatus.org.
EMU33880
Passenger training
Make sure at least one other passenger istrained to operate the boat in the event of anemergency.
EMU33890
Boating safety publications
Be informed about boating safety. Additionalpublications and information can be obtainedfrom many boating organizations.
EMU33590
Laws and regulations
Know the marine laws and regulations whereyou will be boating- and obey them. Severalsets of rules prevail according to geographiclocation, but all are basically the same as theInternational Rules of the Road. The rulespresented in the following section are con-densed- and have been provided for yourconvenience only.Contact the U.S. Coast Guard, the NationalAssociation of State Boating Law Adminis-trators, or your local Power Squadron for acomplete set of rules governing the waters inwhich you will be using your boat.
EMU33681
Boating organizations
The following organizations provide boatingsafety training and information about boatingsafety and laws.
United States Coast Guard
Consumer Affairs Staff (G-BC)Office of Boating, Public, and Consumer Af-fairsU.S. Coast Guard HeadquartersWashington, D.C. 20593-0001Boating Safety Hotline: 1-800-368-5647www.uscgboating.org
United States Power Squadrons
1-888-FOR-USPS (1-888-367-8777)www.usps.org
Boat Owners Association of The UnitedStates
1-800-336-BOAT (1-800-336-2628)www.boatus.com
National Association of State BoatingLaw Administrators (NASBLA)
1500 Leestown Road, Suite 330Lexington, KY 40511 859-225-9497www.nasbla.org
National Marine Manufacturers Associa-tion (NMMA)
200 East Randolph DriveSuite 5100Chicago, IL 60601www.nmma.org
Marine Retailers Association of America
155 N. Michigan Ave. Chicago,IL 60304www.mraa.com
EMU33690
Basic boating rules (Rules of the road)
Just as there are rules that apply when youare driving on streets and highways, thereare waterway rules that apply when you aredriving your boat. These rules are used inter-nationally. (For USA: and are also enforcedby the United States Coast Guard and localagencies.) You should be aware of theserules, and follow them whenever you en-counter another vessel on the water.
Safety information
5
EMU33700
Steering and sailing rules and sound signals
Whenever two vessels on the water meetone another, one vessel has the right-of-way; it is called the “stand-on” vessel. Thevessel that does not have the right-of-way iscalled the “give-way” or “burdened”vessel.These rules determine which vessel has theright-of-way, and what each vessel shoulddo.
Stand-on vessel
The vessel with the right-of-way has the dutyto continue its course and speed, except toavoid an immediate collision. When youmaintain your direction and speed, the othervessel will be able to determine how best toavoid you.
Give-way vessel
The vessel that does not have the right-of-way has the duty to take positive and timelyaction to stay out of the way of the Stand-Onvessel. Normally, you should not cross infront of the vessel with the right-of-way. Youshould slow down or change directions brief-ly and pass behind the other vessel. Youshould always move in such a way that theoperator of the other vessel can see whatyou are doing.
“ The general prudential rule ”
This rule is called Rule 2 in the InternationalRules and says,“ In obeying and construing these rules dueregard shall be had to all dangers of naviga-tion and collision, and to any special circum-stances, which may render a departure fromthe above rules necessary in order to avoidimmediate danger.”In other words, follow the standard rules ex-cept when a collision will occur unless both
vessels try to avoid each other. If that is thecase, both vessels become “ Give-Way ”vessels.
EMU25521
Rules when encountering vessels
There are three main situations that you mayencounter with other vessels which couldlead to a collision unless the Steering Rulesare followed:
Meeting:
(you are approaching another ves-sel head-on)
Crossing:
(you are traveling across the oth-er vessel’s path)
Overtaking:
(you are passing or beingpassed by another vessel)In the following illustration, your boat is in thecenter. You should give the right-of-way toany vessels shown in white area (you are theGive-Way vessel). Any vessels in the shad-ed area must yield to you (they are the Give-Way vessels). Both you and the meetingvessel must alter course to avoid each other.
Meeting
If you are meeting another power vesselhead on, and are close enough to run the riskof collision, neither of you has the right-of-way Both of you should alter course to avoidan accident. You should keep the other ves-sel on your port (left) side. This rule doesn’tapply if both of you will clear one another ifyou continue on your set course and speed.
Safety information
6
Crossing
When two power driven vessels are crossingeach other’s path close enough to run therisk of collision, the vessel which has the oth-er on the starboard (right) side must keep outof the way of the other. If the other vessel ison your right, you must keep out of its way;you are the Give-Way vessel. If the othervessel is on your port (left) side, rememberthat you should maintain course and direc-tion, provided the other vessel gives you theright-of-way as it should.
Overtaking
If you are passing another vessel, you arethe “Give-Way” vessel. This means that theother vessel is expected to maintain itscourse and speed. You must stay out of itsway until you are clear of it. Likewise, if an-other vessel is passing you, you shouldmaintain your speed and direction so that theother vessel can steer itself around you.
EMU25531
Other special situations
There are three other rules you should beaware of when driving your boat around oth-er vessels.
Narrow channels and bends
When navigating in narrow channels, youshould keep to the right when it is safe andpractical to do so. If the operator of a power-driven vessel is preparing to go around abend that may obstruct the view of other wa-ter vessels, the operator should sound a pro-longed blast on the whistle (4 to 6 seconds).If another vessel is around the bend, it tooshould sound the whistle. Even if no reply isheard, however, the vessel should still pro-ceed around the bend with caution. If younavigate such waters with your boat, you willneed to carry a portable air horn, availablefrom local marine supply stores.
Fishing vessel right-of-way
All vessels that are fishing with nets, lines ortrawls are considered to be “fishing vessels”under the International Rules. Vessels withtrolling lines are not considered fishing ves-sels. Fishing vessels have the right-of-wayregardless of position. Fishing vessels can-not, however, impede the passage of othervessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given theright-of-way. The exceptions to this are:1. When the sailing vessel is overtaking
the power-driven vessel, the power-driv-en vessel has the right-of-way.
2. Sailing vessels should keep clear of anyfishing vessel.
3. In a narrow channel, a sailing vesselshould not hamper the safe passage ofa power-driven vessel that can navigateonly in such a channel.
Safety information
7
Reading buoys and other markers
The waters of the United States are markedfor safe navigation by the lateral system ofbuoyage. Simply put, buoys and markershave an arrangement of shapes, colors,numbers and lights to show which side of thebuoy a boater should pass on when navigat-ing in a particular direction. The markings onthese buoys are oriented from the perspec-tive of being entered from seaward (the boat-er is going towards the port). This means thatred buoys are passed on the starboard(right) side when proceeding from open wa-ter into port, and black buoys are to port (left)side. When navigating out of port, your posi-tion with respect to the buoys should be re-versed; red buoys should be to port andblack buoys to starboard.Many bodies of water used by boaters areentirely within the boundaries of a particularstate. The Uniform State Waterway MarkingSystem has been devised for these waters.This system uses buoys and signs with dis-tinctive shapes and colors to show regulato-ry or advisory information. These markersare white with black letters and orangeboarders. They signify speed zones, restrict-ed areas, danger areas, and general infor-mation.Remember, markings may vary by geo-graphic location. Always consult local boat-ing authorities before driving your boat inunfamiliar waters.
Safety information
8
ZMU01708
9
General information
EMU25171
Identification numbers record
EMU25183
Outboard motor serial number
The outboard motor serial number isstamped on the label attached to the portside of the clamp bracket.Record your outboard motor serial number inthe spaces provided to assist you in orderingspare parts from your Yamaha dealer or forreference in case your outboard motor is sto-len.
EMU25190
Key number
If a main key switch is equipped with the mo-tor, the key identification number is stampedon your key as shown in the illustration.Record this number in the space provided forreference in case you need a new key.
1. Outboard motor serial number location
1
ZMU01854
1. Key number
General information
10
EMU33520
Read manuals and labels
Before operating or working on this motor:
�
Read this manual.
�
Read any manuals supplied with the boat.
�
Read all labels on the outboard motor and the boat.If you need any additional information, contact your Yamaha dealer.
EMU33831
Warning labels
If these labels are damaged or missing, contact your Yamaha dealer for replacements.
VZ200R, VZ225H, VZ250F, VZ300B
ZMU06253
3
2
1
General information
11
EMU33850
Other labels
1
2
ZMU05741
3
ZMU05710
General information
12
EMU35132
Symbols
The following symbols mean as follows.
Notice/Warning
Read Owner’s Manual
Hazard caused by continuous rotation
Electrical hazard
ZMU05696
ZMU05664
ZMU05665
ZMU05666
13
Specifications and requirements
EMU31480
SpecificationsTIP:
“(AL)” stated in the specification data belowrepresents the numerical value for the alumi-num propeller installed.Likewise, “(SUS)” represents the value forstainless steel propeller installed and “(PL)”for plastic propeller installed.
EMU2821E
Dimension:
Overall length: 906 mm (35.7 in)
Overall width: 568 mm (22.4 in)
Overall height L: 1714 mm (67.5 in)
Transom height L: 493 mm (19.4 in)
Weight (without propeller) L: 238.0 kg (525 lb)
Performance:
Full throttle operating range: VZ200RTR 5000–6000 r/minVZ225HTR 5000–6000 r/minVZ250FTR 5000–6000 r/minVZ300BTR 4500–6000 r/min
Maximum output: VZ200RTR 147.1 kW@5500 r/min (200 HP@5500 r/min)VZ225HTR 165.5 kW@5500 r/min (225 HP@5500 r/min)VZ250FTR 183.9 kW@5500 r/min (250 HP@5500 r/min)VZ300BTR 220.7 kW@5250 r/min (300 HP@5250 r/min)
Idling speed (in neutral): VZ200RTR 700
±
30 r/minVZ225HTR 700
±
30 r/minVZ250FTR 700
±
30 r/min
VZ300BTR 730
±
30 r/min
Engine:
Type: 2-stroke V
Displacement: 3342.0 cm
3
Bore
×
stroke: 93.0
×
82.0 mm (3.66
×
3.23 in)Ignition system:
TCISpark plug with resistor (NGK):
BKR6EKUSpark plug gap:
1.5–1.6 mm (0.059–0.063 in)Control system:
Remote controlStarting system:
ElectricStarting carburetion system:
Electronic fuel injectionMin. cold cranking amps (CCA/SAE):
512.0 AMin. marine cranking amps (MCA/ABYC):
675.0 AMin. reserve capacity (RC/SAE):
182 minutesMaximum generator output:
50 A
Drive unit:
Gear positions: Forward-neutral-reverse
Gear ratio: VZ200RTR 1.81 (29/16)VZ225HTR 1.75 (28/16)VZ250FTR 1.75 (28/16)VZ300BTR 1.75 (28/16)
Trim and tilt system: Power trim and tilt
Propeller mark: T
Specifications and requirements
14
Fuel and oil:
Recommended fuel: Regular unleaded gasoline
Min. pump octane: 86
Recommended engine oil: YAMALUBE 2-stroke outboard motor oil
Lubrication: Oil injection
Engine oil tank capacity: 1.2 L (1.27 US qt, 1.06 Imp.qt)
Remote oil tank capacity: 10.5 L (11.10 US qt, 9.24 Imp.qt)
Recommended gear oil: Hypoid gear oil SAE#90
Gear oil quantity: 1.050 L (1.110 US qt, 0.924 Imp.qt)
Tightening torque for engine:
Spark plug: 25.0 Nm (2.55 kgf-m, 18.4 ft-lb)
Propeller nut: 55.0 Nm (5.61 kgf-m, 40.6 ft-lb)
EMU33554
Installation requirements
EMU33563
Boat horsepower rating
WARNING
EWM01560
Overpowering a boat can cause severe
instability.
Before installing the outboard motor(s), con-firm that the total horsepower of your mo-tor(s) does not exceed the boats maximumhorsepower rating. See the boat’s capacityplate or contact the manufacturer.
EMU33571
Mounting motor
WARNING
EWM01570
�
Improper mounting of the outboard mo-
tor could result in hazardous condi-tions such as poor handling, loss ofcontrol, or fire hazards.
�
Because the motor is very heavy, spe-cial equipment and training is required
to mount it safely.
Your dealer or other person experienced inproper rigging should mount the motor usingcorrect equipment and complete rigging in-structions. For further information, see page41.
EMU33581
Remote control requirements
WARNING
EWM01580
�
If the engine starts in gear, the boat canmove suddenly and unexpectedly, pos-sibly causing a collision or throwingpassengers overboard.
�
If the engine ever starts in gear, thestart-in-gear protection device is notworking correctly and you should dis-continue using the outboard. Contact
your Yamaha dealer.
The remote control unit must be equippedwith a start-in-gear protection device(s). Thisdevice prevents the engine from starting un-less it is in neutral.
EMU25694
Battery requirements
EMU25713
Specifications of Battery
Use a fully charged battery that meets thefollowing specifications. The engine cannot
Specifications and requirements
15
be started if battery voltage is too low.
NOTICE
ECM01061
Do not use a battery that does not meetthe specified capacity. If a battery thatdoes not meet specifications is used, theelectric system could perform poorly orbe overloaded, causing electric system
damage.
EMU36290
Mounting battery
Mount the battery holder securely in a dry,well-ventilated, vibration-free location in theboat.
WARNING! Do not put flammableitems, or loose heavy or metal objects inthe same compartment as the battery.Fire, explosion or sparks could result.
[EWM01820]
EMU36300
Multiple batteries
To connect multiple batteries, such as formultiple engine configurations or for an ac-cessory battery, consult your Yamaha dealerabout battery selection and correct wiring.
EMU34192
Propeller selection
Next to selecting an outboard, choosing theright propeller is one of the most importantpurchasing decisions a boater can make.The type, size, and design of your propellerhave a direct impact on acceleration, topspeed, fuel economy, and even engine life.
Yamaha designs and manufactures propel-lers for every Yamaha outboard motor andevery application.Your outboard motor came with a Yamahapropeller chosen to perform well over arange of applications, but there may be useswhere a different propeller would be moreappropriate.Your Yamaha dealer can help you select theright propeller for your boating needs. Selecta propeller that will allow the engine to reachthe middle or upper half of the operatingrange at full throttle with the maximum boat-load. Generally, chose a larger pitch propel-ler for a smaller operating load and a smallerpitch propeller for a heavier load. If you carryloads that vary widely, chose the propellerthat lets the engine run in the proper rangefor your maximum load but remember thatyou may need to reduce your throttle settingto stay within the recommended enginespeed range when carrying lighter loads.For instructions on propeller removal and in-stallation, see page 70.
EMU25770
Start-in-gear protection
Yamaha outboard motors or Yamaha-ap-
Minimum cold cranking amps (CCA/SAE):
512.0 AMinimum marine cranking amps (MCA/ABYC):
675.0 AMinimum reserve capacity (RC/SAE):
182 minutes
1. Propeller diameter in inches2. Propeller pitch in inches3. Type of propeller (propeller mark)
ZMU04607
-x1 2 3
Specifications and requirements
16
proved remote control units are equippedwith start-in-gear protection device(s). Thisfeature permits the engine to be started onlywhen it is in neutral. Always select neutralbefore starting the engine.
EMU25661
Engine oil requirements
Use Yamalube 2-M outboard oil. If Ya-malube 2-M is not available, use only anoth-er outboard motor manufacturer’s factory-brand oil with TC-W3 rating.
NOTICE
ECM01290
Serious engine damage can result fromthe use of lower quality oil, includingsome commonly available oil brands with“TC-W3” on their label. To avoid the risk,use only Yamalube 2-M or, if necessary,another outboard motor manufacturer’s
factory-brand TC-W3 oil.
EMU36360
Fuel requirements
EMU36781
Gasoline
Use a good quality gasoline that meets theminimum octane rating. If knocking or ping-ing occurs, use a different brand of gasolineor premium unleaded fuel. Yamaha re-comends that you use alcohol-free (see
Gasohol) gasoline whenever possible.
NOTICE
ECM01981
�
Do not use leaded gasoline. Leadedgasoline can seriously damage the en-gine.
�
Avoid getting water and contaminantsin the fuel tank. Contaminated fuel cancause poor performance or enginedamage. Use only fresh gasoline that
has been stored in clean containers.
Gasohol
There are two types of gasohol: gasohol con-taining ethanol (E10) and that containingmethanol. Ethanol can be used if the ethanolcontent does not exceed 10% and the fuelmeets the minimum octane ratings. E85 is afuel containing 85% ethanol and must not beused in your outboard motor. All ethanolblends containing more than 10% ethanolcan cause fuel system damage or cause en-gine starting and running problems. Yamahadoes not recommend gasohol containingmethanol because it can cause fuel systemdamage or engine performance problems.It is recommended that you install a water-separating marine fuel filter assembly (10micron minimum) between your boat’s fueltank and outboard motor when using etha-nol. Ethanol is known to allow moisture to beabsorbed into boat fuel tanks and systems.Moisture in the fuel can cause corrosion ofmetallic fuel system components, startingand running complaints and require addition-al fuel system maintenance.
Recommended engine oil:YAMALUBE 2 STROKE OUTBOARD OIL
Recommended gasoline:Regular unleaded gasoline with a min-imum Octane rating of 86 (Pump Oc-tane Number) = (R+M)/2
Specifications and requirements
17
EMU27270
Ring Free Fuel Additive
Gasoline is a precise blend of many differentsubstances, each chosen to give certaincharacteristics. Gasoline blends have beenchanging in recent years in response to con-cerns about pollution and resulting emis-sions regulations. One of the most obviouschanges has been the elimination of leadfrom most fuels.As gasoline has changed, the amount of ad-ditives such as aromatics and oxygenateshas increased. These additives are impor-tant for the engines in passenger cars, butthey can have detrimental effects in marineengines, because of increased deposits inthe combustion chamber. When enough de-posits collect, piston rings begin sticking.Performance drops and engine wear in-creases dramatically.While many additives available may reducedeposits, Yamaha recommends the use of
Ring Free Fuel Additive
, available fromyour Yamaha dealer.
Ring Free Fuel Addi-tive
has repeatedly proven its ability to cleancombustion deposits from inside the engine,notably the critical piston-ring-land area, andfuel system components. Follow product la-beling for use instructions.
EMU36880
Muddy or acidic water
Yamaha strongly recommends that you haveyour dealer install the optional chromium-plated water pump kit if you use the outboardmotor in muddy or acidic water conditions.However, depending on the model it mightnot be required.
EMU36330
Anti-fouling paint
A clean hull improves boat performance. Theboat bottom should be kept as clean of ma-rine growth as possible. If necessary, the
boat bottom can be coated with an anti-foul-ing paint approved for your area to inhibitmarine growth.Do not use anti-fouling paint which includescopper or graphite. These paints can causemore rapid engine corrosion.
EMU36341
Motor disposal requirements
Never illegally discard (dump) the motor.Yamaha recommends consulting the dealerabout discarding the motor.
EMU36351
Emergency equipment
Keep the following items onboard in casethere is trouble with the motor.
�
A tool kit with assorted screwdrivers, pli-ers, wrenches (including metric sizes), andelectrical tape.
�
Waterproof flashlight with extra batteries.
�
An extra engine shut-off cord (lanyard)with clip.
�
Spare parts, such as an extra set of sparkplugs.
Consult your Yamaha dealer for details.
EMU25221
Emission control information
EMU25230
North American models
This engine conforms to U.S. EnvironmentalProtection Agency (EPA) regulations for ma-rine SI engines. See the label affixed to your
Specifications and requirements
18
engine for details.
EMU25252
Approval label of emission control certif-icate
This label is attached to the bottom cowling.New Technology ; (4-stroke/HPDI) DFI
EMU25262
Manufactured date label
This label is attached to the clamp bracket orthe swivel bracket.
EMU25273
Star labels
Your outboard motor is labeled with a Cali-fornia Air Resources Board (CARB) star la-bel. See below for a description of yourparticular label.
1. Approval label location
1ZMU04842
ZMU05236
1. Manufactured date label location
1. Star labels location
ZMU048431
Manufactured:
ZMU04346
1
ZMU04844
Specifications and requirements
19
EMU25280
One Star—Low Emission
The one-star label identifies engines thatmeet the Air Resources Board’s 2001 ex-haust emission standards. Engines meetingthese standards have 75% lower emissionsthan conventional carbureted two-stroke en-gines. These engines are equivalent to theU.S. EPA’s 2006 standards for marine en-gines.
EMU25290
Two Stars—Very Low Emission
The two-star label identifies engines thatmeet the Air Resources Board’s 2004 ex-haust emission standards. Engines meetingthese standards have 20% lower emissionsthan One Star-Low-Emission engines.
EMU25300
Three Stars—Ultra Low Emission
The three-star label identifies engines thatmeet the Air Resources Board’s 2008 ex-haust emission standards. Engines meeting
these standards have 65% lower emissionsthan One Star-Low-Emission engines.
EMU33861
Four Stars—Super Ultra Low Emission
The four-star label identifies engines thatmeet the Air Resources Board’s Sterndriveand Inboard marine engine 2009 exhaustemission standards. Personal Watercraftand Outboard marine engines may alsocomply with these standards. Engines meet-ing these standards have 90% lower emis-sions than One Star-Low-Emission engines.
ZMU01702
ZMU01703
ZMU01704
ZMU05663
20
Components
EMU2579M
Components diagramTIP:
* May not be exactly as shown; also may not be included as standard equipment on all mod-els.
VZ200R, VZ225H, VZ250F, VZ300B
TRIPTRIP TIMETIME BATTBATT
Km/hKm/hknotknotmphmph
kmkmmilemile
SPEEDSPEED
YAMAHAYAMAHA
set mode
18
14
19
15
16 17
1
2
13
12
9
10
8
7
6
5
3
4
2
ZMU04845
11
1. Top cowling2. Cowling lock lever(s)3. Trim tab (anode)4. Propeller*5. Cooling water inlet6. Anti-cavitation plate7. Anode8. Clamp bracket9. Tilt support lever10. Flushing device11. Water separator12. Power trim and tilt switch13. Cooling water pilot hole14. Digital tachometer*15. Digital speedometer*
16. Tachometer*17. Trim meter*18. Remote control box (side mount type)*19. Remote oil tank*
Components
21
EMU26181
Remote control box
The remote control lever actuates both theshifter and the throttle. The electrical switch-es are mounted on the remote control box.
1
4 6
32
5
ZMU05429
1. Tachometer unit (Square type)*2. Tachometer unit (Round type)*3. Speedometer unit (Square type)*4. Speed & fuel meter unit (Square type)*5. Speed & fuel meter unit (Round type)*6. Fuel management meter (Square type)*
1. Power trim and tilt switch2. Remote control lever3. Neutral interlock trigger4. Neutral throttle lever5. Main switch6. Engine shut-off switch7. Throttle friction adjuster
Components
22
EMU26190
Remote control lever
Moving the lever forward from the neutral po-sition engages forward gear. Pulling the le-ver back from neutral engages reverse. Theengine will continue to run at idle until the le-ver is moved about 35° (a detent can be felt).Moving the lever farther opens the throttle,and the engine will begin to accelerate.
EMU26201
Neutral interlock trigger
To shift out of neutral, first pull the neutral in-terlock trigger up.
EMU26212
Neutral throttle lever
To open the throttle without shifting into ei-ther forward or reverse, put the remote con-trol lever in the neutral position and lift theneutral throttle lever.
TIP:
The neutral throttle lever will operate onlywhen the remote control lever is in neutral.The remote control lever will operate onlywhen the neutral throttle lever is in the closedposition.
EMU25976
Throttle friction adjuster
A friction device provides adjustable resis-tance to movement of the throttle grip or theremote control lever, and can be set accord-
1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”4. Shift5. Fully closed6. Throttle7. Fully open
1. Neutral interlock trigger
1. Fully open2. Fully closed
Components
23
ing to operator preference.To increase resistance, turn the adjusterclockwise. To decrease resistance, turn theadjuster counterclockwise.
WARNING! Donot overtighten the friction adjuster. Ifthere is too much resistance, it could bedifficult to move the remote control leveror throttle grip, which could result in anaccident.
[EWM00032]
When constant speed is desired, tighten theadjuster to maintain the desired throttle set-ting.
EMU25994
Engine shut-off cord (lanyard) and clip
The clip must be attached to the engine shut-off switch for the engine to run. The cordshould be attached to a secure place on theoperator’s clothing, or arm or leg. Should theoperator fall overboard or leave the helm, thecord will pull out the clip, stopping ignition tothe engine. This will prevent the boat fromrunning away under power.
WARNING! At-tach the engine shut-off cord to a secureplace on your clothing, or your arm or legwhile operating. Do not attach the cord toclothing that could tear loose. Do notroute the cord where it could become en-tangled, preventing it from functioning.Avoid accidentally pulling the cord dur-ing normal operation. Loss of engine
power means the loss of most steeringcontrol. Also, without engine power, theboat could slow rapidly. This could causepeople and objects in the boat to bethrown forward.
[EWM00122]
EMU26091
Main switch
The main switch controls the ignition system;its operation is described below.
�
“ ”
(off)
With the main switch in the “ ” (off) posi-tion, the electrical circuits are off, and the keycan be removed.
�
“ ”
(on)
With the main switch in the “ ” (on) posi-tion, the electrical circuits are on, and the keycannot be removed.
�
“ ”
(start)
With the main switch in the “ ” (start) po-sition, the starter motor turns to start the en-gine. When the key is released, it returnsautomatically to the “ ” (on) position.
1. Cord2. Clip3. Engine shut-off switch
Components
24
EMU32052
Power trim and tilt switch on remote control
The power trim and tilt system adjusts theoutboard motor angle in relation to the tran-som. Pressing the switch “ ” (up) trims theoutboard motor up, and then tilts it up. Press-ing the switch “ ” (down) tilts the outboardmotor down and trims it down. When theswitch is released, the outboard motor willstop in its current position. For instructionson using the power trim and tilt switch, seepages 55 and 57.
EMU26153
Power trim and tilt switch on bottom engine cowling
The power trim and tilt switch is located onthe side of the bottom engine cowling. Press-ing the switch “ ” (up) trims the outboardmotor up, and then tilts it up. Pressing theswitch “ ” (down) tilts the outboard motor
down and trims it down. When the switch isreleased, the outboard motor will stop in itscurrent position.For instructions on using the power trim andtilt switch, see page 57.
WARNING
EWM01030
Use the power trim and tilt switch locatedon the bottom engine cowling only whenthe boat is at a complete stop with the en-gine off. Attempting to use this switchwhile the boat is moving could increasethe risk of falling overboard and coulddistract the operator, increasing the riskof collision with another boat or an obsta-
cle.
EMU26244
Trim tab with anode
WARNING
EWM00840
An improperly adjusted trim tab couldcause difficult steering. Always test runafter the trim tab has been installed or re-placed to be sure steering is correct. Besure you have tightened the bolt after ad-
justing the trim tab.
The trim tab should be adjusted so that thesteering control can be turned to either theright or left by applying the same amount offorce.
UP
DN
ZMU01862
Components
25
If the boat tends to veer to the left (port side),turn the trim tab rear end to the port side “A”in the figure. If the boat tends to veer to theright (starboard side), turn the trim tab end tothe starboard side “B” in the figure.
NOTICE
ECM00840
The trim tab also serves as an anode toprotect the engine from electrochemicalcorrosion. Never paint the trim tab as it
will become ineffective as an anode.
EMU26341
Tilt support lever for power trim and tilt model
To keep the outboard motor in the tilted upposition, lock the tilt support lever to theclamp bracket.
NOTICE
ECM00660
Do not use the tilt support lever or knobwhen trailering the boat. The outboardmotor could shake loose from the tilt sup-port and fall. If the motor cannot be trail-ered in the normal running position, usean additional support device to secure it
in the tilt position.
EMU26392
Cowling lock levers
To remove the outboard motor top cowling,
1. Trim tab2. Bolt3. Cap
Bolt tightening torque:42.0 Nm (4.2 kgf-m, 31 ft-lb)
AB
ZMU01863
ZMU01864
Components
26
pull up the front and rear cowling lock levers.Then lift off the cowling. When the cowling,check to be sure it fits properly in the rubberseal. Then lock the cowling again by movingthe cowling lock levers downward.
NOTICE
ECM00550
The air intake grille on the top cowling isnot designed as a handle and could break
if used as such.
EMU26461
Flushing device
This device is used to clean the cooling wa-ter passages of the motor using a gardenhose and tap water.
TIP:
For details on usage, see page 62.
EMU33462
Fuel filter/Water separator
This engine has a combination fuel filter/wa-ter separator and associated alert system. Ifwater separated from the fuel exceeds aspecific volume, the alert device of Com-mand Link Tachometer will activate.
Activation of alert device
�
The water separator-alert indicator ofCommand Link Tachometer will blink.
�
The buzzer will sound intermittently onlywhen the gear shift is in neutral.
�
If the alert system has activated, stop theengine and consult a Yamaha dealer im-mediately.
TIP:
Adding an in-line 10-micron fuel filter has
1. Cowling lock lever(s)
1. Air intake grille2. Cowling lock lever(s)
ZMU04840
1
1 1
2 2
ZMU04841
1. Flushing device
1
ZMU01866
ZMU05499
Components
27
been show to greatly reduce the chance offuel contamination problems. Consult yourdealer for information about Yamaha 10-mi-cron fuel filters if your boat does not haveone.
28
Instruments and indicators
EMU26493
Digital tachometer
The tachometer shows the engine speedand has the following functions.All segments of the display will light momen-tarily after the main switch is turned on andwill return to normal thereafter.
TIP:
The water separator and engine trouble-alertindicators only operate when the engine isequipped with the appropriate functions.
EMU36050
Tachometer
The tachometer displays engine speed inhundreds of revolutions per minute (r/min).For example, if the tachometer display reads“22” then the engine speed is 2200 r/min.
EMU26621
Trim meter
This meter shows the trim angle of your out-board motor.
�
Memorize the trim angles that work bestfor your boat under different conditions.Adjust the trim angle to the desired using
the power trim and tilt switch.
�
If the trim angle of your motor exceeds thetrim operating range, the top segment onthe trim meter display will blink.
EMU26651
Hour meter
This meter shows the number of hours theengine has been run. It can be set to showthe total number of hours or the number ofhours for the current trip. The display canalso be turned on and off.
To change the display format, press the“ ” (mode) button. The display can showtotal hours or trip hours, or turn off.To reset the trip hours, simultaneously pressthe “ ” (set) and “ ” (mode) buttons formore than 1 second while the trip hours aredisplayed. This resets the trip counter to 0(zero).The total number of hours the engine hasbeen run cannot be reset.
1. Tachometer2. Trim meter3. Hour meter4. Oil level indicator5. Overheat-alert indicator6. Set button7. Mode button
1
3
56 7
4
2
ZMU01891
ZMU01869
ZMU01870
Instruments and indicators
29
EMU26551
Oil level indicator (digital type)
This indicator shows the engine oil level. Ifthe oil level falls below the lower limit, thealert indicator will start to blink. For further in-formation, see page 39.
NOTICE
ECM00030
Do not operate the engine without oil. Se-
rious engine damage will occur.
EMU26583
Overheat-alert indicator
If the engine temperature rises too high, thealert indicator will start to blink. For further in-formation on reading the indicator, see page39.
NOTICE
ECM00052
Do not continue to run the engine if theoverheat-alert indicator is on. Serious en-
gine damage will occur.
EMU26602
Digital speedometer
This gauge shows the boat speed and otherinformation.
All segments of the display will light momen-tarily after the main switch is turned on andwill return to normal thereafter.
EMU36061
Speedometer
The speedometer displays km/h, mph, orknots, according to operator preference. Se-lect the desired units of measurement by set-ting the selector switch on the back of thegauge. See the illustration for settings.
1. Oil level indicator
1ZMU01867
1. Overheat-alert indicator
1. Speedometer2. Fuel gauge3. Trip meter/clock/voltmeter4. Alert indicator(s)
1
ZMU01868
Instruments and indicators
30
EMU26712
Fuel gauge
Eight segments indicate the fuel level. Whenall segments are showing, the fuel tank isfull.
The fuel level reading can be inaccurate dueto by the position of the sensor in the fueltank and the attitude of the boat in the water.Operation with bow-up trim or continuousturning can give false readings.Do not adjust the selector switch for fuel sen-sor. Incorrectly setting the selector switch onthe gauge will give false readings. Consultyour Yamaha dealer on how to correctly setthe selector switch.
NOTICE:
Running outof fuel can damage the engine.
[ECM01770]
EMU36071
Trip meter / Clock / Voltmeter
The display shows either the trip meter, theclock, or the voltmeter.To change the display, press the “ ”(mode) button repeatedly until the indicatoron the face of the gauge points to “ ” (tripmeter), “ ” (clock), or “ ” (voltmeter).
EMU26691
Trip meter
This gauge displays the distance the boathas traveled since the gauge was last reset.The trip distance is shown in kilometers ormiles depending upon the unit of measure-ment selected for the speedometer.To reset the trip meter to zero, press the “ ”(set) and “ ” (mode) buttons at the sametime.The trip distance is kept in memory by bat-tery power. The stored data will be lost if thebattery is disconnected.
EMU26701
Clock
To set the clock:1. Be sure the gauge is in the “ ” (time)
mode.2. Press the “ ” (set) button; the hour dis-
play will begin blinking.3. Press the “ ” (mode) button until the
desired hour is displayed.4. Press the “ ” (set) button again, the
minute display will begin blinking.
1. Cap2. Selector switch (for speed unit)3. Selector switch (for fuel sensor)
ZMU01745
Instruments and indicators
31
5. Press the “ ” (mode) button until thedesired minute is displayed.
6. Press the “ ” (set) button again to startthe clock.
The clock operates on battery power. Dis-connecting the battery will stop the clock.Reset the clock after connecting the battery.
EMU36080
Voltmeter
The voltmeter displays the charge of the bat-tery in volts(V).
EMU26721
Fuel level-alert indicator
If the fuel level decreases to one segment,the fuel level alert segment will blink.Do not continue to operate the engine withfull throttle if an alert device has activated.Get back to the port within trolling enginespeed.
NOTICE:
Running out of fuel candamage the engine.
[ECM01770]
EMU26732
Low battery voltage-alert indicator
If battery voltage drops, the display will auto-matically turn on and blink.Get back to the port soon if an alert devicehas activated. For charging the battery, con-sult your Yamaha dealer.
EMU26471
Analog tachometer
This gauge shows the engine speed and hasthe following functions.
EMU26541
Oil level indicators (three indicators)
The indicators on the gauge show the statusof the oil level. For details on how to read the
1. Fuel level-alert segment
1. Low battery indicator
1. Tachometer2. Alert indicator(s)
ZMU04577
1
2
Instruments and indicators
32
indicators, see page 50.
NOTICE
ECM00030
Do not operate the engine without oil. Se-
rious engine damage will occur.
EMU26611
Analog trim meter
This gauge shows the trim angle of your out-board motor.
Memorize the trim angles that work best foryour boat under different conditions. Adjustthe trim angle to the desired setting with thepower trim and tilt switch.
EMU31642
Command link multifunction meters
Command link multifunction meters have 6kinds of meter units; tachometer unit (square
or round types), speedometer unit (squaretype), speed & fuel meter unit (square orround types), and fuel management meter(square type). The indicator system is slight-ly different between the round and squaretypes. Check the model and type of your unitcarefully. This manual describes mainly thealert indicators. For more details on settingmeters or changing indicator systems, seethe attached operation manual.
EMU36103
Command link multifunction tachometers
The tachometer shows the engine revolu-tions per minute. It has functions of trimmeter, adjusting trolling speed, cooling wa-ter/engine temperature display, battery volt-age display, total hour/trip hour display, oilpressure display, water detection alert, en-gine trouble alert, and periodic maintenancenotification. If the cooling water pressuresensor is installed, the unit can also show thecooling water pressure display. However,even if the cooling water pressure sensor isnot installed, the cooling water pressure dis-play can be shown by connecting an optionalsensor to the unit. For the optional sensor,consult your Yamaha dealer. The tachome-ter unit is available in round or square types.Check your tachometer unit type.
1. Oil level indicators
ZMU04580
1
ZMU04581
1. Set button
21
ZMU05415
Instruments and indicators
33
EMU36110
Start-up checks
Place the remote control lever in neutral andturn the main switch to “ ” (on). After all thedisplays come on and the total hour displaycomes on, the gauge will change to normaloperation. If the buzzer sounds and the wa-ter separator-alert indicator blinks, consultyour Yamaha dealer immediately.
TIP:
To stop the buzzer, press the “ ” (set) or“ ” (mode) button.
EMU36260
Oil level alert
When the oil level is low while cruising, theoil level-alert indicator will start to blink. Theengine speed will automatically decrease toabout 2000 r/min.
2. Mode button
1. Tachometer2. Trim meter3. Multifunction display4. Cooling water pressure5. Cooling water/engine temperature6. Water detection-alert indicator7. Battery voltage8. Oil level (2-stroke models)
1. Set button2. Mode button
2
3
1
4
5
6
7
8ZMU05452
21
ZMU05417
1. Tachometer2. Trim meter3. Multifunction display4. Water detection-alert indicator5. Engine trouble alert/maintenance indicator6. Cooling water pressure7. Oil level (2-stroke models)8. Cooling water/engine temperature9. Battery voltage
1 4 5 2
3
6 97 8 ZMU05453
Instruments and indicators
34
When the buzzer sounds and the oil level-alert indicator blinks, check the oil level andadd the oil if necessary. If the alert devicehas activated while the appropriate engineoil level is maintained, consult your Yamahadealer.
NOTICE
ECM01581
Do not continue to run the engine if the oillevel alert device has activated. Serious
engine damage will occur.
EMU36221
Overheat alert
If the engine temperature rises too high whilecruising, the overheat-alert indicator will startto blink. The engine speed will automaticallydecrease to about 2000 r/min.
Stop the engine immediately if the buzzersounds and the overheat alert device has ac-tivated. Check the cooling water inlet forclogging.
NOTICE
ECM01592
�
Do not continue to run the engine if theoverheat-alert indicator blinks. Seriousengine damage will occur.
�
Do not continue to operate the engine ifa alert device has activated. Consultyour Yamaha dealer if the problem can-
not be located and corrected.
EMU36150
Water separator alert
This indicator will blink if water has accumu-lated in the water separator (fuel filter) whilecruising. In such an event, stop the engineimmediately and see page 79 of this manualto drain the water from the fuel filter. Getback to the port soon and consult a Yamaha
ZMU05419
ZMU05420
ZMU05421
ZMU05422
Instruments and indicators
35
dealer immediately.
NOTICE
ECM00910
Gasoline mixed with water could cause
damage to the engine.
EMU36160
Engine trouble alert
This indicator will blink if the engine malfunc-tions while cruising. Get back to the portsoon and consult a Yamaha dealer immedi-ately.
NOTICE
ECM00920
In such an event, the engine will not oper-ate properly. Consult a Yamaha dealer
immediately.
EMU36170
Low battery voltage-alert
If the battery voltage drops, the low batteryvoltage-alert indicator and the battery volt-age value will start to blink. Get back to theport soon if the low battery voltage-alert de-vice has activated. For charging the battery,consult your Yamaha dealer.
ZMU05423
ZMU05424
ZMU05425
ZMU05426
Instruments and indicators
36
EMU31613
Command link multifunction speed & fuel meters
The speed & fuel meter unit shows the boatspeed and has the functions of fuel meter, to-tal fuel consumption display, fuel economydisplay, fuel flow display, and system voltagedisplay. The chosen display is selected byusing the “ ” (set) and “ ” (mode) but-tons as described in this section. If the speedsensor is installed, the unit can also show thetrip display. However, even if the speed sen-sor is not installed, the trip display can beshown by connecting an optional sensor tothe unit. In addition, if optional sensors areconnected to the unit, water surface temper-ature display, depth display, and clock willalso be available. For the optional sensors,consult your Yamaha dealer.The speed & fuel meter unit is available inround or square types. Check your speed &
fuel meter unit type for operation information.After the main switch is first turned on, all thedisplays come on as a test. After a few sec-onds, the gauge will change to normal oper-ation.For more information, see the operationmanual originally supplied with the meter.
ZMU05427
ZMU05428
1. Set button2. Mode button
1. Speedometer2. Fuel meter3. Multifunction display
21
ZMU05432
1
23
ZMU05433
Instruments and indicators
37
EMU31622
Command link multifunction speedometers
The speedometer unit shows the boat speedand has functions of fuel meter and systemvoltage display. The chosen display is se-lected by using the “ ” (set) and “ ”(mode) buttons as described in this section.In addition, the speedometer can show thedesired unit of measurement such as km/h,mph, or knots. If the speed sensor is in-stalled, the unit can also show the trip dis-play. However, even if the speed sensor isnot installed, the trip display can be shown
by connecting an optional sensor to the unit.In addition, if optional sensors are connectedto the unit, water surface temperature dis-play, depth display, and clock will also beavailable. For the optional sensors, consultyour Yamaha dealer.After the main switch is first turned on, all thedisplays come on as a test. After a few sec-onds, the gauge will change to normal oper-ation.For more information, see the operationmanual originally supplied with the meter.
1. Set button2. Mode button
1. Speedometer2. Fuel meter3. Multifunction display
21
ZMU05434
1 2
3 ZMU05435
1. Set button2. Mode button
1. Speedometer2. Fuel meter3. Multifunction display
21
ZMU05436
1
23
ZMU05437
Instruments and indicators
38
EMU31632
Command link multifunction fuel management meters
The fuel management meter has the func-tions of fuel flow meter, total consumptiondisplay, fuel economy display, and remain-ing fuel display. The chosen display is select-ed by using the “ ” (set) and “ ” (mode)buttons as described in this section. Formore information, see the operation manualoriginally supplied with the meter.After the main switch is first turned on, all thedisplays come on as a test. After a few sec-onds, the gauge will change to normal oper-ation.For more information, see the operationmanual originally supplied with the meter.
1. Set button2. Mode button
1. Fuel flow meter
21
ZMU05438
1
2
ZMU05439
2. Multifunction display
39
Engine control system
EMU26803
Alert system
NOTICE
ECM00091
Do not continue to operate the engine if aalert device has activated. Consult yourYamaha dealer if the problem cannot be
located and corrected.
EMU2681A
Overheat alert
This engine has an overheat-alert device. Ifthe engine temperature rises too high, thealert device will activate.
�
The engine speed will automatically de-crease to about 2000 r/min.
�
The overheat-alert indicator will light orblink.
�
The buzzer will sound (if equipped on thetiller handle, remote control box, or mainswitch panel).
If the alert system has activated, stop the en-gine and check the cooling water inlets:
�
Check trim angle to be sure that the cool-ing water inlet is submerged.
�
Check the cooling water inlet for clogging.
EMU26848
Oil level alert and oil filter clogging alert
Oil injection models
This engine has an oil level alert system. Ifthe oil level falls below the lower limit, thealert system will activate.
Activation of alert device
�
Engine speed will automatically decreaseto about 2000 r/min.
�
The oil level-alert indicator will light orblink.
ZMU01757
ZMU04766
ZMU02373
Engine control system
40
�
The buzzer will sound (if equipped on thetiller handle, remote control box, or mainswitch panel).
If the alert system has been activated, stopthe engine and check for the cause.
TIP:
The alert for oil filter clogging is similar to thealerts for low oil level and overheating. Tomake troubleshooting easier, check for en-gine overheating first, then oil level, and fi-
nally oil filter clogging.
ZMU03942
ZMU04586
ZMU03025
1. Oil filter
1. Oil filter
1
ZMU01872
1ZMU01952
41
Installation
EMU26902
Installation
The information presented in this section isintended as reference only. It is not possibleto provide complete instructions for everypossible boat and motor combination. Prop-er mounting depends in part on experienceand the specific boat and motor combination.
WARNING
EWM01590
�
Overpowering a boat could cause se-vere instability. Do not install an out-board motor with more horsepowerthan the maximum rating on the capac-ity plate of the boat. If the boat does nothave a capacity plate, consult the boatmanufacturer.
�
Improper mounting of the outboard mo-tor could result in hazardous condi-tions such as poor handling, loss ofcontrol, or fire hazards. For permanent-ly mounted models, your dealer or oth-er person experienced in proper
rigging should mount the motor.
EMU33470
Mounting the outboard motor
The outboard motor should be mounted sothat the boat is well balanced. Otherwise, theboat could be hard to steer. For single-en-gine boats, mount the outboard motor on thecenterline (keel line) of the boat.
EMU26953
Mounting height
To run your boat at optimum efficiency, thewater resistance (drag) of the boat and out-board motor must be made as little as possi-ble. The mounting height of the outboardmotor greatly affects the water resistance. Ifthe mounting height is too high, cavitationtends to occur, thus reducing the propulsionand causing the engine to overheat. If themounting height is too low, the water resis-tance will increase and thereby reduce en-gine efficiency. Mount the outboard motor sothat the anti-cavitation plate is about 130 mm(5 in) above the bottom of the boat.
NOTICE
ECM01631
�
Check that the idle hole stays highenough to keep out water getting inside
1. Center line (keel line)
1 ZMU01873
ZMU02098
130 mm (5 in)
Installation
42
engine even if the boat is in stationarywith maximum load.
�
Incorrect engine height or obstructionsto the smooth flow of water (such as thedesign or condition of the boat, or ac-cessories such as transom ladders ordepth finder transducers) can createairborne water spray while the boat iscruising. If the motor is operated con-tinuously in the presence of airbornewater spray, enough water could enterthe engine through the intake openingon the cowling to cause severe enginedamage. Eliminate the cause of the air-
borne water spray.
TIP:
�
The optimum mounting height of the out-board motor is affected by the boat andmotor combination and the desired use.Test runs at different heights can help de-termine the optimum mounting height.Consult your Yamaha dealer or boat man-ufacturer for further information on deter-mining the proper mounting height.
�
For instructions on setting the trim angle ofthe outboard motor, see page 55.
43
Operation
EMU36381
First-time operation
EMU27042
Breaking in engine
Your new engine requires a period of break-in to allow mating surfaces of moving parts towear in evenly. Correct break-in will help en-sure proper performance and longer enginelife.
NOTICE
ECM00750
�
Failure to follow the break-in procedurecould result in reduced engine life oreven severe engine damage.
�
Do not use premixed fuel in this enginebecause it could cause carbon depos-its on the fuel injector and engine trou-ble.
�
Follow the instructions for break-in
carefully.
EMU27092
Procedure for HPDI models
Run the engine under load (in gear with apropeller installed) for 10 hours as follows.1. First 10 minutes:
Run the engine at the lowest possiblespeed. A fast idle in neutral is best.
2. Next 50 minutes:Do not exceed half throttle (approxi-mately 3000 r/min). Vary engine speedoccasionally. If you have an easy-plan-ing boat, accelerate at full throttle ontoplane, then immediately reduce thethrottle to 3000 r/min or less.
3. Next 2 hours:Accelerate at full throttle onto plane,then reduce engine speed to three-quar-ter throttle (approximately 4000 r/min).Vary engine speed occasionally. Run atfull throttle for 1 minute, then allow about10 minutes of operation at three-quarter
throttle or less to let the engine cool.4. Remaining 7 hours:
Run the engine at any speed. However,avoid operating at full throttle for morethan 5 minutes at a time.
5. After the first 10 hours:Operate the engine normally.
EMU36400
Getting to know your boat
Different boats handle differently. Operatecautiously while you learn how your boathandles under different conditions and withdifferent trim angles (see page 55).
EMU36412
Checks before starting engine
WARNING
EWM01920
If any item in the checks before startingengine is not working properly, have it in-spected and repaired before operatingthe outboard motor. Otherwise an acci-
dent could occur.
NOTICE
ECM00120
Do not start the engine out of water. Over-heating and serious engine damage can
occur.
EMU37151
Fuel level
Be sure you have plenty of fuel for your trip.A good rule is to use 1/3 of your fuel to get tothe destination, 1/3 to return, and to keep 1/3 as an emergency reserve. With the boatlevel on a trailer or in the water, turn the keyto “ ” (on) and check the fuel level. For fuelfilling instructions, see page 48.
EMU36431
Remove cowling
For the following checks, remove the topcowling from the engine. To remove the en-gine cowling, release all the lock levers and
Operation
44
lift off the cowling.
EMU36442
Fuel system
WARNING
EWM00060
Gasoline and its vapors are highly flam-mable and explosive. Keep away fromsparks, cigarettes, flames, or other
sources of ignition.
WARNING
EWM00910
Leaking fuel can result in fire or explo-sion.
�
Check for fuel leakage regularly.
�
If any fuel leakage is found, the fuelsystem must be repaired by a qualifiedmechanic. Improper repairs can make
the outboard unsafe to operate.
EMU36451
Check for fuel leaks
�
Check for fuel leaks or gasoline fumes in
the boat.
�
Check for fuel leakage from the fuel sys-tem.
�
Check the fuel tank and fuel lines forcracks, swellings, or other damages.
EMU36470
Check the fuel filter
Check that the fuel filter is clean and free ofwater. If enough water to raise the float ringis found in the fuel, or if a significant amountof debris is found, the fuel tank should bechecked and cleaned by a Yamaha dealer.
EMU36461
Controls
�
Turn the steering wheel full-right and full-left. Make sure operation is smooth andunrestricted throughout the whole rangewith no binding or excessive free play.
�
Operate the throttle levers several times tomake sure there is no hesitation in theirtravel. Operation should be smooth overthe complete range of motion, and each le-ver should return completely to the idle po-sition.
�
Look for loose or damaged connections ofthe throttle and shift cables.
EMU36482
Engine shut-off cord (lanyard)
Inspect the engine shut-off cord for damage,such as cuts, breaks, and wear.
ZMU06106
ZMU06102ZMU05499
Operation
45
EMU27120
Oil
�
Check to be sure you have plenty of oil foryour trip.
EMU27153
Engine
�
Check the engine and engine mounting.
�
Look for loose or damaged fasteners.
�
Check the propeller for damage.
�
Check for engine oil leaks.
EMU27222
Operation after a long period of storage
When operating the engine after a long peri-od (12 months) of storage, proceed as fol-lows:1. Start the engine. Leave it idling.
WARNING! Do not touch or removeelectrical parts when starting or dur-ing operation. Keep hands, hair, andclothes away from the flywheel andother rotating parts while the engineis running.
[EWM00091]
2. Watch for oil flowing through the oil feed
pipes. After any air in the oil lines hasbeen expelled, the oil injection systemshould supply oil normally. If no oil isflowing after 10 minutes of idling, consult
your Yamaha dealer.
NOTICE:
Be sureto take the above steps when operat-ing the engine after a long period ofstorage. Otherwise engine seizurecould occur. Use straight gasolineonly. If premix fuel is used, the fuel in-jector could be damaged.
[ECM00561]
1. Cord2. Clip3. Engine shut-off switch
ZMU01875
Operation
46
EMU36490
Flushing device
Check that flushing device’s garden hoseconnector is securely screwed on to the fit-ting on the bottom cowling.
NOTICE:
If theflushing device is not properly connect-ed, cooling water can leak out and the en-gine can overheat during operation.
[ECM01800]
EMU36940
Install cowling
1. Be sure that all cowling lock levers arereleased.
2. Be sure that the rubber seal is seated allthe way around the engine.
3. Place the cowling on top of the seal.4. Check to be sure it fits properly in the
rubber seal.5. Move the levers to lock the cowling as
shown.
NOTICE:
If the cowling is notinstalled correctly, water spray underthe cowling can damage the engine,or the cowling can blow off at highspeeds.
[ECM01990]
After installing, check the fitting of the topcowling by pushing it with both hands. If thetop cowling is loose, have it repaired by yourYamaha dealer.
1. Fitting2. Flushing device
ZMU01876
2
1
ZMU06049
ZMU06131
ZMU06127
Operation
47
EMU29158
Checking power trim and tilt system
WARNING
EWM01930
�
Never get under the lower unit while itis tilted, even when the tilt support leveris locked. Severe injury could occur ifthe outboard motor accidentally falls.
�
Body parts can be crushed between themotor and the clamp bracket when themotor is trimmed or tilted.
�
Be sure no one is near the outboard
motor before performing this check.
1. Check the power trim and tilt unit for anysign of oil leaks.
2. Operate each of the power trim and tiltswitches on the remote control and en-gine bottom cowling to check that allswitches work.
3. Tilt the outboard motor up and checkthat the tilt rod and trim rods are extend-ed completely.
4. Use the tilt support lever to lock the mo-tor in the up position. Operate the tiltdown switch briefly so the motor is sup-ported by the tilt support lever.
5. Check that the tilt rod and trim rods arefree of corrosion or other flaws.
6. Activate the tilt-down switch until the trimrods have retracted completely into thecylinders.
1. Tilt rod2. Trim rods
1. Tilt support lever
ZMU03458
1
2
ZMU04155
1
Operation
48
7. Activate the trim-up switch until the tiltrod is fully extended. Unlock the tilt sup-port lever.
8. Tilt the outboard motor down. Checkthat the tilt rod and trim rods operatesmoothly.
EMU36582
Battery
Check that the battery is in good condition,and fully charged. Check that the batteryconnections are clean, secure and coveredby insulating covers. The electrical contactsof the battery and cables must be clean andproperly connected or the battery will notstart the engine.Refer to the battery manufacturer’s instruc-tions for checks for your particular battery.
EMU27234
Filling fuel and engine oil
EMU30321
Filling fuel for models without a fuel joint
WARNING
EWM01830
�
Gasoline and its vapors are highly flam-mable and explosive. Always refuel ac-cording to this procedure to reduce therisk of fire and explosion.
�
Gasoline is poisonous and can causeinjury or death. Handle gasoline withcare. Never siphon gasoline by mouth.If you should swallow some gasoline orinhale a lot of gasoline vapor, or getsome gasoline in your eyes, see yourdoctor immediately. If gasoline spillson your skin, wash with soap and wa-ter. If gasoline spills on your clothing,
change your clothes.
1. Stop the engine.2. Be sure you are in a well-ventilated out-
door area, either securely moored ortrailered.
3. Make sure no one is in the boat.4. Do not smoke and keep away from
sparks, flames, static electric discharge,or other sources of ignition.
5. If you use a portable container to storeand dispense fuel, only use a locally ap-proved GASOLINE container.
6. Touch the fuel nozzle to the filler open-ing or funnel to help prevent electrostaticsparks.
7. Fill the fuel tank, but do not overfill. Fuelcan expand and overflow if the tempera-ture increases.
8. Tighten the filler cap securely.9. Wipe up any spilled gasoline immediate-
ly with dry rags. Dispose rags properly.
ZMU04156
ZMU03460
Operation
49
According to local laws or regulations.
EMU27292
Filling oil for oil injection models
WARNING
EWM00530
Do not add gasoline into the oil tank. Fire
or explosion could result.
This engine uses the Yamaha oil injectionsystem, which provides superior lubricationby ensuring the proper oil ratio for all operat-ing conditions. No fuel premixing is needed.Simply pour gasoline into the fuel tank andoil into the oil tank. Convenient indicatorsshow the status of the oil supply. For detailson how to read the indicators, see page 50.To fill the engine oil tank, proceed as follows:1. Pour engine oil into the remote oil tank.
TIP:
The oil level lines on the remote oil tank indi-cate the amount of additional oil that can beadded to the tank. The top oil level line indi-cates approximately 1.9 L (0.5 US gal, 0.4Imp gal) can be added, and the bottom oillevel line indicates approximately 3.8 L (1 USgal, 0.8 Imp gal) can be added.2. Turn on the main switch. The Yamaha
oil injection system will automatically
feed oil from the remote oil tank to theengine oil tank.
3. Operate the engine normally.
NOTICE
ECM00570
When the engine is operated for the firsttime or stored for a period of time, a min-imum of 5 liters (5.3 US qt, 4.4 Imp qt) ofoil should be kept in the remote oil tank.Otherwise the oil-feed pump chamber willnot be filled with oil, and no oil will be
supplied.
Remote oil tank capacity:10.5 L (11.10 US qt, 9.24 Imp.qt)
ZMU01877
Operation
50
EMU27321
Oil level indicator operation
The various functions of the oil level system are as follows:
EMU27383
Oil level indicator
Electric start models
Oil level-alert indicator (digital
tachometer)
Oil level-alert indicator (analog
tachometer)
Engine oil tank
Remote oil tank
Remarks
Green
more than 300
cm
3
(0.32 US qt, 0.26 Imp
qt)
more than
1500 cm
3
(1.6 US qt, 1.31
Imp qt)
�
No refilling necessary.
Yellow
more than 300
cm
3
(0.32 US qt, 0.26 Imp
qt)
1500 cm
3
(1.6 US qt, 1.31 Imp qt) or less
�
Add oil; see page 49.
Red–Yellow–Green
300 cm
3
(0.32 US qt, 0.26
Imp qt) or less
more than
1500 cm
3
(1.6 US qt, 1.31 Imp qt)
�
Check oil filter for clog-ging.
�
Check battery cable connection. Buzzer will sound.
�
Engine speed is auto-matically reduced to about 2000 r/min.
Red
300 cm
3
(0.32 US qt, 0.26
Imp qt) or less
1500 cm
3
(1.6 US qt, 1.31 Imp qt) or less
�
Oil has not been added.
�
Buzzer will sound.
�
Engine speed is auto-matically reduced to about 2000 r/min.
�
Buzzer sounds in remote control box and engine speed is limited to about 2000 r/min to help conserve oil.
Operation
51
EMU27451
Operating engine
EMU27483
Sending fuel
WARNING
EWM00420
�
Before starting the engine, make surethat the boat is tightly moored and thatyou can steer clear of any obstructions.Be sure there are no swimmers in thewater near you.
�
When the air vent screw is loosened,gasoline vapor will be released. Gaso-line is highly flammable, and its vaporsare flammable and explosive. Refrainfrom smoking, and keep away fromopen flames and sparks while loosen-ing the air vent screw.
�
This product emits exhaust gaseswhich contain carbon monoxide, a col-orless, odorless gas which could causebrain damage or death when inhaled.Symptoms include nausea, dizziness,and drowsiness. Keep cockpit and cab-in areas well ventilated. Avoid blocking
exhaust outlets.
1. If there is an air vent screw on the fueltank cap, loosen it 2 or 3 turns.
2. If there is a fuel joint or a fuel cock on theboat, firmly connect the fuel line to thejoint or open the fuel cock.
3. Squeeze the primer pump, with the ar-row pointing up, until you feel it becomefirm.
EMU27493
Starting engine
WARNING
EWM01600
Before starting the engine, make surethat the boat is tightly moored and thatyou can steer clear of any obstructions.Be sure there are no swimmers in the wa-
ter near you.
EMU27664
Electric start and remote control models
WARNING
EWM01840
�
Failure to attached engine shut-off cordcould result in a runaway boat if opera-tor is ejected. Attach the engine shut-off cord to a secure place on your cloth-ing, or your arm or leg while operating.Do not attach the cord to clothing thatcould tear loose. Do not route the cordwhere it could become entangled, pre-venting it from functioning.
�
Avoid accidentally pulling the cord dur-ing normal operation. Loss of enginepower means the loss of most steeringcontrol. Also, without engine power,the boat could slow rapidly. This couldcause people and objects in the boat to
be thrown forward.
1. Arrow
Operation
52
1. Place the remote control lever in neutral.
TIP:
The start-in-gear protection device preventsthe engine from starting except when in neu-tral.2. Attach the engine shut-off cord to a se-
cure place on your clothing, or your armor leg. Then install the clip on the otherend of the cord into the engine shut-offswitch.
3. Turn the main switch to “ ” (on).4. Turn the main switch to “ ” (start),
and hold it for a maximum of 5 seconds.
5. Immediately after the engine starts, re-lease the main switch and allow it to re-turn to “ ” (on).
NOTICE:
Never turnthe main switch to “ ” (start)while the engine is running. Do notkeep the starter motor turning formore than 5 seconds. If the startermotor is turned continuously formore than 5 seconds, the battery willbe quickly discharged, thus making itimpossible to start the engine. Thestarter can also be damaged. If theengine will not start after 5 secondsof cranking, return the main switch to“ ” (on), wait 10 seconds, thencrank the engine again.
[ECM00192]
TIP:
�
When the engine is cold, it needs to bewarmed up. For further information, seepage 53.
�
If the engine is warm and fails to start,open the throttle slightly and try to start theengine again. If the engine still fails tostart, see page 76.
EMU36510
Checks after starting engine
EMU36520
Cooling water
Check for a steady flow of water from thecooling water pilot hole. A continuous flow ofwater from the pilot hole shows that the wa-
ZMU03239
Operation
53
ter pump is pumping water through the cool-ing passages. If the cooling passages arefrozen, it may take a while for water to startflowing out of the pilot hole.
NOTICE
ECM01810
If water is not flowing out of the pilot holeat all times while the engine is running,overheating and serious damage couldoccur. Stop the engine and check wheth-er the cooling water inlet on the lowercase or the cooling water pilot hole isblocked. Consult your Yamaha dealer ifthe problem cannot be located and cor-
rected.
Check that no water leaks from the joints be-tween the exhaust cover, cylinder head, andbody cylinder.
EMU27670
Warming up engine
EMU27704
Electric start and prime start models
After starting the engine, allow it to idle for 3minutes to warm up. Failure to do so willshorten engine life.
EMU36530
Checks after engine warm-up
EMU36540
Shifting
While tightly moored, and without applyingthrottle, confirm that the engine shifts
smoothly into forward and reverse, and backto neutral.
EMU31721
Stop switches
�
Confirm that turning the main switch to the“ ” (off) position stops the engine.
�
Confirm that removing the clip from the en-gine shut-off switch stops the engine.
�
Confirm that the engine cannot be startedwith the clip removed from the engineshut-off switch.
EMU31730
Shifting
WARNING
EWM00180
Before shifting, make sure there are noswimmers or obstacles in the water near
you.
NOTICE
ECM01610
Warm up the engine before shifting intogear. Until the engine is warm, the idlespeed may be higher than normal. Highidle speed can prevent you from shiftingback to neutral. If this occurs, stop theengine, shift to neutral, then restart the
engine and allow it to warm up.
To shift out of neutral1. Pull the neutral interlock trigger up (if
equipped).
ZMU01882
Operation
54
2. Move the remote control lever firmly andcrisply forward (for forward gear) orbackward (for reverse gear) about 35° (adetent can felt).
To shift from in gear (forward/reverse) toneutral1. Close the throttle so that the engine
slows to idle speed.
2. After the engine is at idle speed in gear
move the remote control lever firmly andcrisply into the neutral position.
EMU31742
Stopping boat
WARNING
EWM01510
�
Do not use the reverse function to slowdown or stop the boat as it could causeyou to lose control, be ejected, or im-pact the steering wheel or other parts ofthe boat. This could increase the risk ofserious injury. It could also damage theshift mechanism.
�
Do not shift into reverse while travelingat planing speeds. Loss of control, boatswamping, or damage to the boat could
occur.
The boat is not equipped with a separatebraking system. Water resistance stops it af-ter the throttle lever is moved back to idle.The stopping distance varies depending ongross weight, water surface conditions, andwind direction.
EMU27821
Stopping engine
Before stopping the engine, first let it cool offfor a few minutes at idle or low speed. Stop-ping the engine immediately after operatingat high speed is not recommended.
1. Neutral interlock trigger
Operation
55
EMU31831
Procedure
1. Turn the main switch to “ ” (off).
2. Remove the key if the boat will be leftunattended.
TIP:
The engine can also be stopped by pullingthe cord and removing the clip from the en-gine shut-off switch, then turning the mainswitch to “ ” (off).
EMU27862
Trimming outboard motor
WARNING
EWM00740
Excessive trim for the operating condi-tions (either trim up or trim down) cancause boat instability and can makesteering the boat more difficult. This in-creases the possibility of an accident. Ifthe boat begins to feel unstable or is hardto steer, slow down and/or readjust the
trim angle.
The trim angle of the outboard motor helpsdetermine the position of the bow of the boatin the water. Correct trim angle will help im-prove performance and fuel economy whilereducing strain on the engine. Correct trimangle depends upon the combination ofboat, engine, and propeller. Correct trim isalso affected by variables such as the load inthe boat, sea conditions, and running speed.
EMU27885
Adjusting trim angle (Power trim and tilt)
WARNING
EWM00753
�
Be sure all people are clear of the out-board motor when adjusting the trimangle. Body parts can be crushed be-tween the motor and the clamp bracketwhen the motor is trimmed or tilted.
�
Use caution when trying a trim positionfor the first time. Increase speed gradu-ally and watch for any signs of instabil-ity or control problems. Improper trimangle can cause loss of control.
�
If equipped with a power trim and tiltswitch located on the bottom cowling,use the switch only when the boat is ata complete stop with the engine off. Donot adjust the trim angle with this
1. Trim operating angle
1ZMU01983
Operation
56
switch while the boat is moving.
Adjust the outboard motor trim angle usingthe power trim and tilt switch.
To raise the bow (trim-out), press the switch“ ” (up).To lower the bow (trim-in), press the switch“ ” (down).Make test runs with the trim set to differentangles to find the position that works best foryour boat and operating conditions.
EMU27912
Adjusting boat trim
When the boat is on plane, a bow-up attituderesults in less drag, greater stability and effi-ciency. This is generally when the keel line ofthe boat is up about 3 to 5 degrees. With thebow up, the boat may have a greater tenden-
cy to steer to one side or the other. Compen-sate for this as you steer. When the bow ofthe boat is down, it is easier to acceleratefrom a standing start onto plane.
Bow Up
Too much trim-out puts the bow of the boattoo high in the water. Performance and econ-omy are decreased because the hull of theboat is pushing the water and there is moreair drag. Excessive trim-out can also causethe propeller to ventilate, which reduces per-formance further, and the boat may “por-poise” (hop in the water), which could throwthe operator and passengers overboard.
Bow Down
Too much trim-in causes the boat to “plow”through the water, decreasing fuel economyand making it hard to increase speed. Oper-ating with excessive trim-in at higher speedsalso makes the boat unstable. Resistance atthe bow is greatly increased, heightening the
1. Power trim and tilt switch
1. Power trim and tilt switch
UP
DN
ZMU01944
1
Operation
57
danger of “bow steering” and making opera-tion difficult and dangerous.
TIP:
Depending on the type of boat, the outboardmotor trim angle may have little effect on thetrim of the boat when operating.
EMU27934
Tilting up and down
If the engine will be stopped for some time orif the boat is moored in shallows, the out-board motor should be tilted up to protect thepropeller and lower casing from damage bycollision with obstructions, and also to re-duce salt corrosion.
WARNING
EWM00221
Be sure all people are clear of the out-board motor when tilting up and down.Body parts can be crushed between themotor and the clamp bracket when the
motor is trimmed or tilted.
WARNING
EWM00250
Leaking fuel is a fire hazard. If there is afuel joint on the outboard motor, discon-nect the fuel line or close the fuel cock ifthe engine will be tilted for more than a
few minutes. Otherwise fuel may leak.
NOTICE
ECM00241
�
Before tilting the outboard motor, stopthe engine by following the procedureon page 54. Never tilt the outboard mo-tor while the engine is running. Severedamage from overheating can result.
�
Do not tilt up the engine by pushing thetiller handle (if equipped) because this
could break the handle.
EMU32724
Procedure for tilting up (power trim and tilt models)
1. Place the remote control lever in neutral.
2. Press the power trim and tilt switch “ ”(up) until the outboard motor has tiltedup completely.
N
ZMU03196
Operation
58
3. Pull the tilt support lever toward you tosupport the engine.
WARNING! Aftertilting the outboard motor, be sure tosupport it with the tilt support knob ortilt support lever. Otherwise the out-board motor could fall back downsuddenly if oil in the power trim andtilt unit or in the power tilt unit losespressure.
[EWM00262]
NOTICE:
Do not usethe tilt support lever or knob whentrailering the boat. The outboard mo-tor could shake loose from the tiltsupport and fall. If the motor cannotbe trailered in the normal running po-sition, use an additional support de-vice to secure it in the tilt position.For more detailed information, seepage 61.
[ECM01641]
4. Models equipped with trim rods: Oncethe outboard motor is supported with thetilt support lever, press the power trim
and tilt switch “ ” (down) to retract thetrim rods.
NOTICE:
Be sure to retractthe trim rods completely duringmooring. This protects the rods frommarine growth and corrosion whichcould damage the power trim and tiltmechanism.
[ECM00251]
EMU33121
Procedure for tilting down (power trim and tilt models)
1. Push the power trim and tilt switch “ ”(up) until the outboard motor is support-ed by the tilt rod and the tilt support leverbecomes free.
2. Release the tilt support lever.
3. Push the power trim and tilt switch “ ”(down) to lower the outboard motor tothe desired position.
UP
ZMU01954
ZMU01886
ZMU03997
ZMU03998
Operation
59
EMU28061
Shallow water
EMU32851
Power trim and tilt models
The outboard motor can be tilted up partiallyto allow operation in shallow water.
NOTICE
ECM00260
Do not tilt the outboard motor up so thatthe cooling water inlet on the lower unit isabove the surface of the water when set-ting up for and cruising in shallow water.Otherwise severe damage from overheat-
ing can result.
EMU32922
Procedure for power trim and tilt models
1. Place the remote control lever in neutral.
2. Slightly tilt the outboard motor up to thedesired position using the power trimand tilt switch.
WARNING! Using thepower trim and tilt switch on the bot-tom cowling while the boat is movingor engine is on could increase therisk of falling overboard and coulddistract the operator, increasing therisk of collision with another boat oran obstacle.
[EWM01850]
DN
ZMU01936
UP
DN
DN
ZMU01979
UP
ZMU01935
UP
DN
UP
ZMU01954
Operation
60
3. To return the outboard motor to the nor-mal running position, press the powertrim and tilt switch and slowly tilt the out-board motor down.
EMU28195
Cruising in other conditions
Cruising in salt water
After operating in salt water, flush the coolingwater passages with fresh water to preventthem from becoming clogged. Also rinse theoutside of the outboard motor with fresh wa-ter.
Cruising in muddy, turbid, or acidic water
Yamaha strongly recommends that you usethe optional chromium-plated water pump kit(see page 17) if you use the outboard motorin acidic water or water with a lot of sedimentin it, such as muddy or turbid (cloudy) water.After operating in such water, flush the cool-ing passages with fresh water to prevent cor-rosion. Also rinse the outside of the outboardmotor with fresh water.
61
Maintenance
EMU31841
Transporting and storing outboard motor
WARNING
EWM01860
Leaking fuel is a fire hazard. When trans-porting and storing the outboard motor,close the fuel cock to prevent fuel fromleaking. Never get under the engine whileit is tilted. Severe injury could occur if the
outboard motor accidentally falls.
NOTICE
ECM00660
Do not use the tilt support lever or knobwhen trailering the boat. The outboardmotor could shake loose from the tilt sup-port and fall. If the motor cannot be trail-ered in the normal running position, usean additional support device to secure it
in the tilt position.
The outboard motor should be trailered andstored in the normal running position. If thereis insufficient road clearance in this position,then trailer the outboard motor in the tilt po-sition using a motor support device such asa transom saver bar. Consult your Yamahadealer for further details.
EMU30250
Storing outboard motor
When storing your Yamaha outboard motor
for prolonged periods of time (2 months orlonger), several important procedures mustbe performed to prevent excessive damage.This is especially important for your oil injec-tion equipped outboard motor due to the leanoil ratios used at idle prior to shutting the en-gine off for the season. It is advisable to haveyour outboard motor serviced by an autho-rized Yamaha dealer prior to storage. How-ever, you, the owner, with a minimum oftools, can perform the following procedures.
NOTICE
ECM01390
Do not use any chemical goods contain-ing Silicon, Phosphorus, or Lead. Con-sult your Yamaha dealer for details on the
use of chemical goods for storage.
EMU28304
Procedure
EMU31921
Conditioning and stabilizing fuel
Fill the fuel tank with fresh fuel and add oneounce of “Yamaha Fuel Conditioner and Sta-bilizer” to each gallon of fuel.
TIP:
The use of “Yamaha Fuel Conditioner andStabilizer” eliminates the need to drain thefuel system. Consult your Yamaha dealer orother qualified mechanic if the fuel system isto be drained instead.
EMU31900
Engine anti-rust measure
NOTICE
ECM01530
Do not perform this procedure while theengine is running. The water pump maybe damaged and severe damage from
overheating can result.
TIP:
This procedure is performed while the topcowling is removed.
ZMU03659
Maintenance
62
1. Remove the spark plug(s).2. Pour a teaspoonful of clean engine oil
into each cylinder.3. Crank the engine several times manual-
ly.4. Reinstall the spark plug(s).
EMU31392
Washing the outboard motorTIP:
This procedure is performed while the topcowling is installed.1. Wash the outboard motor body using
fresh water.
NOTICE:
Do not spray wa-ter into the air intake.
[ECM01840]
2. Drain the cooling water completely out
of the motor. Clean the body thoroughly.
EMU28411
Lubrication (oil injection models)
1. Install the spark plug(s) and torque toproper specification. For information onspark plug installation, see page 68.
2. Fill the oil tanks. This prevents the for-mation of condensation. For models witha remote oil tank, it may be necessary tomanually override the control unit tocompletely fill the engine oil tank.
3. Change the gear oil. For instructions,see page 72. Inspect the oil for the pres-ence of water which indicates a leakyseal. Seal replacement should be per-formed by an authorized Yamaha dealerprior to use.
4. Grease all grease fittings. For further de-tails, see page 68.
TIP:
For long-term storage, fogging the enginewith oil is recommended. Contact yourYamaha dealer for information about foggingoil and procedures for your engine.
EMU30266
Cleaning and anticorrosion measures
1. Wash down the exterior of the outboardmotor with fresh water and dry off com-pletely.
NOTICE:
Do not spray waterinto the air intake.
[ECM01840]
2. Spray the outboard motor exterior with
“Yamaha Silicone Protectant”.
NOTICE:
Do not spray when the engine is run-ning. Also, do not spray near the si-lencer or into the engine. Otherwisethe engine could be damaged.
[ECM01402]
3. Wax the cowling with a non-abrasive
wax such as “Yamaha Silicone Wax”.
EMU28443
Flushing power unit
Perform this procedure right after operationfor the most thorough flushing.
NOTICE
ECM01530
Do not perform this procedure while theengine is running. The water pump maybe damaged and severe damage from
overheating can result.
1. After shutting off the engine, unscrewthe garden hose connector from the fit-ting on the bottom cowling.
Maintenance
63
2. Screw the garden hose adapter onto agarden hose, which is connected to afresh water supply, and then connect itto the garden hose connector.
3. With the engine off, turn on the water tapand let the water flush through the cool-ing passages for about 15 minutes. Turnoff the water and disconnect the gardenhose adapter from the garden hose con-nector.
4. Reinstall the garden hose connectoronto the fitting on the bottom cowling.Tighten the connector securely.
NO-TICE:
Do not leave the garden hoseconnector loose on the bottom cowl-ing fitting or let the hose hang freeduring normal operation. Water willleak out of the connector instead of
cooling the engine, which can causeserious overheating. Be sure the con-nector is tightened securely on thefitting after flushing the engine.
[ECM00541]
TIP:
�
When flushing the engine with the boat inthe water, tilting up the outboard motor un-til it is completely out of the water willachieve better results.
�
For cooling system flushing instructions,see page 61.
EMU28451
Cleaning the outboard motor
After use, wash the exterior of the outboardmotor with fresh water. Flush the coolingsystem with fresh water.
EMU28460
Checking painted surface of motor
Check the motor for scratches, nicks, or flak-ing paint. Areas with damaged paint aremore likely to corrode. If necessary, cleanand paint the areas. A touch-up paint is avail-able from your Yamaha dealer.
EMU2848A
Periodic maintenance
WARNING
EWM01871
These procedures require mechanicalskills, tools, and supplies. If you do nothave the proper skills, tools, or supplies
1. Fitting2. Garden hose connector3. Garden hose adapter
12 3
ZMU01984
ZMU01985
Maintenance
64
to perform a maintenance procedure,have a Yamaha dealer or other qualifiedmechanic do the work.The procedures involve disassemblingthe motor and exposing dangerous parts.To reduce the risk of injury from moving,hot, or electrical parts:
�
Turn off the engine and keep the key(s)and engine shut-off cord (lanyard) withyou when you perform maintenanceunless otherwise specified.
�
The power trim and tilt switches oper-ate even when the ignition key is off.Keep people away from the switcheswhenever working around the motor.When the motor is tilted, keep awayfrom the area under it or between it andthe clamp bracket. Be sure no one is inthis area before operating the powertrim and tilt mechanism.
�
Allow the engine to cool before han-dling hot parts or fluids.
�
Always completely reassemble the mo-
tor before operation.
Maintenance, replacement, or repair ofthe emission control devices and sys-tems may be performed by any marineengine repair establishment or individual.All warranty repairs, however, includingthose to the emission control system,must be performed by an authorizedYamaha marine dealership.
A service manual is available for purchasethrough your Yamaha dealer for owners whohave the mechanical skills, tools, and otherequipment necessary to perform mainte-nance not covered by this owner’s manual.
EMU28511
Replacement parts
If replacement parts are necessary, use onlygenuine Yamaha parts or parts of equivalent
design and quality. Any part of inferior qualitymay malfunction, and the resulting loss ofcontrol could endanger the operator andpassengers. Yamaha genuine parts and ac-cessories are available from your Yamahadealer.
EMU35520
Maintenance interval guidelines
The service intervals provided in the Mainte-nance Chart were developed based upon“typical” use that includes operating at variedspeeds, with sufficient time for engine warmup and cool-down, a medium to light load,and an average cruising speed near the3000 to 4000 rpm range. As with any engine,however, if your normal operating conditionsare different, you should consider servicemore often than shown, especially how oftenyou change your engine and gear oil. Exam-ples might include extended wide-open-throttle use or long periods of trolling oridling, carrying heavy loads, or frequentstarting and stopping or shifting. More fre-quent maintenance will often pay off manytimes over in increased engine life and great-er owner satisfaction. Consult your Yamahadealer for additional maintenance recom-mendations.
Maintenance
65
EMU34445
Maintenance chart 1TIP:
�
Refer to the sections in this chapter for explanations of each owner-specific action.
�
The maintenance cycle on these charts assume usage of 100 hours per year and regularflushing of the cooling water passages. Maintenance frequency should be adjusted whenoperating the engine under adverse conditions such as extended trolling.
�
Disassembly or repairs may be necessary depending on the outcome of maintenancechecks.
�
Expendable or consumable parts and lubricants will lose their effectiveness over time andthrough normal usage regardless of the warranty period.
�
When operating in salt water, muddy, other turbid (cloudy), acidic water, the engine shouldbe flushed with clean water after each use.
The “ ” symbol indicates the check-ups which you may carry out yourself.The “ ” symbol indicates work to be carried out by your Yamaha dealer.
Item Actions
Initial Every
20 hours (3
months)
100 hours (1
year)
300 hours (3 years)
500 hours (5 years)
Anode(s) (external)Inspection or replace-ment as necessary
Anode(s) (cylinder head, thermostat cover)
Inspection or replace-ment as necessary
Anodes (exhaust cover, cooling water passage cover, Rectifier Regula-tor cover)
Replacement
Battery (electrolyte level, terminal)
Inspection
Battery (electrolyte level, terminal)
Fill, charging or replac-ing as necessary
Cooling water leakageInspection or replace-ment as necessary
Cowling lock lever Inspection
Engine starting condi-tion/noise
Inspection
Engine idling speed/noise
Inspection
Fuel filter (can be dis-assembled)
Inspection or replace-ment as necessary
Fuel line(High pres-sure)
Inspection
Maintenance
66
Fuel line(High pres-sure)
Inspection or replace-ment as necessary
Fuel line(Low pres-sure)
Inspection
Fuel line(Low pres-sure)
Inspection or replace-ment as necessary
Fuel pumpInspection or replace-ment as necessary
Fuel/engine oil leakage Inspection
Gear oil Replacement
Greasing points Greasing
Impeller/water pump housing
Inspection or replace-ment as necessary
Impeller/water pump housing
Replacement
Oil tank water drain Inspection or cleaning
Oil injection pump/oil feed pump
Inspection or Adjust-ment
Power trim and tilt unit/Operation, noise and oil leakage
Inspection
Propeller/propeller nut/cotter pin
Inspection or replace-ment as necessary
PCV (Pressure Con-trol Valve)
Inspection or replace-ment as necessary
Shift link/shift cableInspection, adjustment or replacement as nec-essary
Spark plug(s)Inspection or replace-ment as necessary
Spark plug caps/spark plug wires
Inspection or replace-ment as necessary
Water from the cooling water pilot hole
Inspection
Throttle link/throttle cable/throttle pick-up timing
Inspection, adjustment or replacement as nec-essary
ThermostatInspection or replace-ment as necessary
Item Actions
Initial Every
20 hours (3
months)
100 hours (1
year)
300 hours (3 years)
500 hours (5 years)
Maintenance
67
EMU34451
Maintenance chart 2
Water inlet Inspection
Main switch/stop switch/choke switch
Inspection or replace-ment as necessary
Wire harness connec-tions/wire coupler con-nections
Inspection or replace-ment as necessary
(Yamaha) Meter/gauge Inspection
Item ActionsEvery
1000 hours
Fuel Filter (Vapor sep-arator tank) (HPDI models)
Replacement
High pressure fuel pump drive belt (HPDI models)
Replacement
Exhaust guide/exhaust manifold
Inspection or replace-ment as necessary
Item Actions
Initial Every
20 hours (3
months)
100 hours (1
year)
300 hours (3 years)
500 hours (5 years)
Maintenance
68
EMU28932
Greasing
Yamaha marine grease (Water resistant grease)
VZ200R, VZ225H, VZ250F, VZ300B
EMU28956
Cleaning and adjusting spark plug
The spark plug is an important engine com-ponent and is easy to inspect. The conditionof the spark plug can indicate somethingabout the condition of the engine. For exam-ple, if the center electrode porcelain is very
white, this could indicate an intake air leak orcarburetion problem in that cylinder. Do notattempt to diagnose any problems yourself.Instead, take the outboard motor to aYamaha dealer. You should periodically re-move and inspect the spark plug becauseheat and deposits will cause the spark plug
ZMU01986
Maintenance
69
to slowly break down and erode.1. Remove the spark plug caps from the
spark plugs.2. Remove the spark plug. If electrode ero-
sion becomes excessive, or if carbonand other deposits are excessive, youshould replace the spark plug with an-other of the correct type.
WARNING!When removing or installing a sparkplug, be careful not to damage the in-sulator. A damaged insulator couldallow external sparks, which couldlead to explosion or fire.
[EWM00561]
3. Be sure to use the specified spark plug,otherwise the engine may not operateproperly. Before fitting the spark plug,measure the electrode gap with a wirethickness gauge; replace it if out of spec-ification.
4. When fitting the plug, wipe off any dirtfrom the threads, and then screw it in to
the correct torque.
TIP:
If a torque-wrench is not available when youare fitting a spark plug, a good estimate ofthe correct torque is 1/4 to 1/2 a turn past fin-ger-tight. Have the spark plug adjusted to thecorrect torque as soon as possible with atorque-wrench.
EMU29043
Inspecting idling speed
WARNING
EWM00451
�
Do not touch or remove electrical partswhen starting or during operation.
�
Keep hands, hair, and clothes awayfrom the flywheel and other rotating
parts while the engine is running.
NOTICE
ECM00490
This procedure must be performed whilethe outboard motor is in the water. Aflushing attachment or test tank can be
used.
If the boat is not equipped with a tachometerfor the outboard motor, use a diagnostic ta-chometer for this procedure. Results mayvary depending on whether testing is con-ducted with the flushing attachment, in a testtank, or with the outboard motor in the water.1. Start the engine and allow it to warm up
fully in neutral until it is running smooth-ly.
2. Once the engine has warmed up, verifywhether the idle speed is set to specifi-cation. For idle speed specifications,see page 13. If you have difficulty verify-ing the idle speed, or the idle speed re-
Standard spark plug:BKR6EKU
1. Spark plug gap2. Spark plug part number3. Spark plug I.D. mark (NGK)
Spark plug gap:1.5–1.6 mm (0.059–0.063 in)
1
12
3
ZMU01892
Spark plug torque:25.0 Nm (2.55 kgf-m, 18.4 ft-lb)
Maintenance
70
quires adjustment, consult a Yamahadealer or other qualified mechanic.
EMU29050
Checking water in engine oil tank
Oil injection models
There is a water trap at the bottom of the en-gine oil tank. If water or foreign matter is vis-ible in this trap, consult your Yamaha dealer.
EMU29113
Checking wiring and connectors
�
Check that each connector is engaged se-curely.
�
Check that each ground lead is properlysecured.
EMU32112
Checking propeller
WARNING
EWM01881
You could be seriously injured if the en-gine accidentally starts when you arenear the propeller. Before inspecting, re-moving, or installing the propeller, placethe shift control in neutral, turn the mainswitch to “ ” (off) and remove the key,and remove the clip from the engine shut-off switch. Turn off the battery cut-off
switch if your boat has one.
Do not use your hand to hold the propellerwhen loosening or tightening the propellernut. Put a wood block between the anti-cavi-tation plate and the propeller to prevent thepropeller from turning.
1. Water trap2. Engine oil tank
21
ZMU01895
Maintenance
71
Checkpoints
�
Check each of the propeller blades for ero-sion from cavitation or ventilation, or otherdamage.
�
Check the propeller shaft for damage.
�
Check the splines for wear or damage.
�
Check for fish line tangled around the pro-peller shaft.
�
Check the propeller shaft oil seal for dam-age.
EMU30662
Removing propeller
EMU29197
Spline models
1. Straighten the cotter pin and pull it outusing a pair of pliers.
2. Remove the propeller nut, washer, andspacer (if equipped).
WARNING! Donot use your hand to hold the propel-ler when loosening the propeller nut.
[EWM01890]
3. Remove the propeller, washer (ifequipped), and thrust washer.
EMU30672
Installing propeller
EMU29233
Spline models
NOTICE
ECM00500
Be sure to use a new cotter pin and bendthe ends over securely. Otherwise thepropeller could come off during opera-
tion and be lost.
1. Apply Yamaha marine grease or a cor-rosion resistant grease to the propellershaft.
2. Install the spacer (if equipped), thrustwasher, washer (if equipped), and pro-peller on the propeller shaft.
NOTICE:
Be sure to install the thrust washerbefore installing the propeller, other-wise the lower case and propellerboss could be damaged.
[ECM01880]
3. Install the spacer (if equipped) and the
washer. Tighten the propeller nut to the
ZMU01897
1. Cotter pin2. Propeller nut3. Washer4. Spacer5. Propeller6. Thrust washer
1
6 54
32
ZMU01898
Maintenance
72
specified torque.
4. Align the propeller nut with the propellershaft hole. Insert a new cotter pin in thehole and bend the cotter pin ends.
NO-TICE:
Do not reuse the cotter pin in-stalled. Otherwise the propeller cancome off during operation.
[ECM01890]
TIP:
If the propeller nut does not align with thepropeller shaft hole after tightening to thespecified torque, tighten the nut further toalign it with the hole.
EMU31913
Changing gear oil
WARNING
EWM00800
�
Be sure the outboard motor is securelyfastened to the transom or a stablestand. You could be severely injured ifthe outboard motor falls on you.
�
Never get under the lower unit while itis tilted, even when the tilt support leveror knob is locked. Severe injury couldoccur if the outboard motor accidental-
ly falls.
1. Tilt the outboard motor so that the gearoil drain screw is at the lowest point pos-
sible.2. Place a suitable container under the
gear case.3. Remove the cooling water inlet covers
on both sides of the gear case. Be care-ful not to lose the bolt and nut.
4. Remove the gear oil drain screw andgasket. The screw is magnetic so asmall quantity of metal particles on theend of the screw is normal. Simply re-move them.
NOTICE:
If there is an ex-cessive quantity of metal particles onthe magnetic gear oil drain screw,this can indicate lower unit problem.Consult your Yamaha dealer.
[ECM01900]
5. Remove the oil level plug and gasket toallow the oil to drain completely.
NO-TICE:
Inspect the used oil after it hasbeen drained. If the oil is milky, wateris getting into the gear case whichcan cause gear damage. Consult aYamaha dealer for repair of the lowerunit seals.
[ECM00711]
TIP:
For disposal of used oil, consult yourYamaha dealer.6. Put the outboard motor in a vertical po-
sition. Using a flexible or pressurized fill-
Propeller nut tightening torque:55.0 Nm (5.61 kgf-m, 40.6 ft-lb)
ZMU02063
1. Gear oil drain screw2. Oil level plug
ZMU020961
2
Maintenance
73
ing device, inject the gear oil into thegear oil drain screw hole.
7. Put a new gasket on the oil level plug.When the oil begins to flow out of the oillevel plug hole, insert and tighten the oillevel plug.
8. Put a new gasket on the gear oil drainscrew. Insert and tighten the gear oildrain screw.
9. Securely install the cooling water inletcovers on both sides of the gear caseusing the bolt and nut removed earlier.
EMU29313
Inspecting and replacing anode(s)
Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect theexternal anodes periodically. Remove scalesfrom the surfaces of the anodes. Consult aYamaha dealer for replacement of externalanodes.
NOTICE
ECM00720
Do not paint anodes, as this would render
them ineffective.
TIP:
Inspect ground leads attached to externalanodes on equipped models. Consult aYamaha dealer for inspection and replace-ment of internal anodes attached to the pow-er unit.
Recommended gear oil:Hypoid gear oil SAE#90
Gear oil quantity:1.050 L (1.110 US qt, 0.924 Imp.qt)
Tightening torque:9 Nm (0.9 kgf-m, 6.6 ft-lb)
Tightening torque:9 Nm (0.9 kgf-m, 6.6 ft-lb)
Tightening torque:5 Nm (0.5 kgf-m, 3.6 ft-lb)
ZMU02364
ZMU01901
ZMU01902
Maintenance
74
EMU29322
Checking battery (for electric start models)
WARNING
EWM01900
Battery electrolytic fluid is poisonousand caustic, and batteries generate ex-plosive hydrogen gas. When workingnear the battery:
�
Wear protective eye gear and rubbergloves.
�
Do not smoke or bring any other sourceof ignition near the battery.
Refer to page 14 for detailed safety infor-
mation about batteries.
The procedure for checking the battery var-ies for different batteries. This procedurecontains typical checks that apply to manybatteries, but you should always refer to thebattery manufacturer’s instructions.
NOTICE
ECM01920
A poorly maintained battery will quickly
deteriorate.
1. Check the electrolyte level.
2. Check the battery’s charge. If your boatis equipped with the digital speedome-ter, the voltmeter and low battery alertfunctions will help you monitor the bat-tery’s charge. If the battery needs charg-
ing, consult your Yamaha dealer.3. Check the battery connections. They
should be clean, secure, and covered byan insulating cover.
WARNING! Badconnections can produce shorting orarcing and cause an explosion.
[EWM01910]
EMU35493
Connecting the battery
WARNING
EWM00570
Mount the battery holder securely in adry, well-ventilated, vibration-free loca-tion in the boat. Install a fully charged bat-
tery in the holder.
NOTICE
ECM01123
Reversal of the battery cables will dam-
age the electrical parts.
1. Make sure the main switch (on applica-ble models) is “ ” (off) before workingon the battery.
2. Connect the red battery cable to thePOSITIVE (+) terminal first. Then con-nect the black battery cable to the NEG-ATIVE (-) terminal.
3. The electrical contacts of the battery and
1. Red cable2. Black cable3. Battery
Maintenance
75
cables must be clean and properly con-nected, or the battery will not start theengine.
Connecting an accessory battery (optional)1. If connecting an accessory battery, con-
sult your Yamaha dealer about correctwiring. For the fuse size, see ABYC (E-11).
Single engine
EMU29371
Disconnecting the battery
1. Turn off the battery cut-off switch (ifequipped) and main switch.
NOTICE:
Ifthey are left on, the electrical systemcan be damaged.
[ECM01930]
2. Disconnect the negative cable(s) fromthe negative (-) terminal.
NOTICE:
Al-ways disconnect all negative (-) ca-bles first to avoid a short circuit anddamage to the electrical system.
[ECM01940]
3. Disconnect the positive cable(s) and re-
move the battery from the boat.4. Clean, maintain, and store the battery
according to the manufacturer’s instruc-tions.
1. Isolator lead with circuit protection2. Red cable3. Black cable4. Fuse5. Battery for accessories6. Battery for starting7. Negative connecting cable
2 1
7
6 5
3
4
ZMU05939
76
Trouble Recovery
EMU29427
Troubleshooting
A problem in the fuel, compression, or igni-tion systems can cause poor starting, loss ofpower, or other problems. This section de-scribes basic checks and possible remedies,and covers all Yamaha outboard motors.Therefore some items may not apply to yourmodel.If your outboard motor requires repair, bringit to your Yamaha dealer.If the engine trouble-alert indicator is flash-ing, consult your Yamaha dealer.
Starter will not operate.
Q. Is battery capacity weak or low?A. Check battery condition. Use battery ofrecommended capacity.
Q. Are battery connections loose or corrod-ed?A. Tighten battery cables and clean batteryterminals.
Q. Is fuse for electric start relay or electric cir-cuit blown?A. Check for cause of electric overload andrepair. Replace fuse with one of correct am-perage.
Q. Are starter components faulty?A. Have serviced by a Yamaha dealer.
Q. Is shift lever in gear?A. Shift to neutral.
Engine will not start (starter operates).
Q. Is fuel tank empty?A. Fill tank with clean, fresh fuel.
Q. Is fuel contaminated or stale?
A. Fill tank with clean, fresh fuel.
Q. Is fuel filter clogged?A. Clean or replace filter.
Q. Is starting procedure incorrect?A. See page 51.
Q. Has fuel pump malfunctioned?A. Have serviced by a Yamaha dealer.
Q. Are spark plug(s) fouled or of incorrecttype?A. Inspect spark plug(s). Clean or replacewith recommended type.
Q. Are spark plug cap(s) fitted incorrectly?A. Check and re-fit cap(s).
Q. Is ignition wiring damaged or poorly con-nected?A. Check wires for wear or breaks. Tightenall loose connections. Replace worn or bro-ken wires.
Q. Are ignition parts faulty?A. Have serviced by a Yamaha dealer.
Q. Is engine shut-off cord (lanyard) not at-tached?A. Attach cord.
Q. Are engine inner parts damaged?A. Have serviced by a Yamaha dealer.
Engine idles irregularly or stalls.
Q. Are spark plug(s) fouled or of incorrecttype?A. Inspect spark plug(s). Clean or replacewith recommended type.
Trouble Recovery
77
Q. Is fuel system obstructed?A. Check for pinched or kinked fuel line orother obstructions in fuel system.
Q. Is fuel contaminated or stale?A. Fill tank with clean, fresh fuel.
Q. Is fuel filter clogged?A. Clean or replace filter.
Q. Have ignition parts failed?A. Have serviced by a Yamaha dealer.
Q. Has alert system activated?A. Find and correct cause of alert.
Q. Is spark plug gap incorrect?A. Inspect and adjust as specified.
Q. Is ignition wiring damaged or poorly con-nected?A. Check wires for wear or breaks. Tightenall loose connections. Replace worn or bro-ken wires.
Q. Is specified engine oil not being used?A. Check and replace oil as specified.
Q. Is thermostat faulty or clogged?A. Have serviced by a Yamaha dealer.
Q. Are carburetor adjustments incorrect?A. Have serviced by a Yamaha dealer.
Q. Is fuel pump damaged?A. Have serviced by a Yamaha dealer.
Q. Is air vent screw on fuel tank closed?A. Open air vent screw.
Q. Is choke knob pulled out?
A. Return to home position.
Q. Is motor angle too high?A. Return to normal operating position. Q. Is carburetor clogged?A. Have serviced by a Yamaha dealer.
Q. Is fuel joint connection incorrect?A. Connect correctly.
Q. Is throttle valve adjustment incorrect?A. Have serviced by a Yamaha dealer.
Q. Is battery cable disconnected?A. Connect securely.
Alert buzzer sounds or indicator lights.
Q. Is cooling system clogged?A. Check water intake for restriction.
Q. Is engine oil level low?A. Fill oil tank with specified engine oil.
Q. Is heat range of spark plug incorrect?A. Inspect spark plug and replace it with rec-ommended type.
Q. Is specified engine oil not being used?A. Check and replace oil with specified type.
Q. Is engine oil contaminated or deteriorat-ed?A. Replace oil with fresh, specified type.
Q. Is oil filter clogged?A. Have serviced by a Yamaha dealer.
Q. Has oil feed/injection pump malfunc-tioned?A. Have serviced by a Yamaha dealer.
Trouble Recovery
78
Q. Is load on boat improperly distributed?A. Distribute load to place boat on an evenplane.
Q. Is water pump or thermostat faulty?A. Have serviced by a Yamaha dealer.
Q. Is there excess water in fuel filter cup?A. Drain filter cup.
Engine power loss.
Q. Is propeller damaged?A. Have propeller repaired or replaced.
Q. Is propeller pitch or diameter incorrect?A. Install correct propeller to operate out-board at its recommended speed (r/min)range.
Q. Is trim angle incorrect?A. Adjust trim angle to achieve most efficientoperation.
Q. Is motor mounted at incorrect height ontransom?A. Have motor adjusted to proper transomheight.
Q. Has alert system activated?A. Find and correct cause of alert.
Q. Is boat bottom fouled with marine growth?A. Clean boat bottom.
Q. Are spark plug(s) fouled or of incorrecttype?A. Inspect spark plug(s). Clean or replacewith recommended type.
Q. Are weeds or other foreign matter tangled
on gear housing?A. Remove foreign matter and clean lowerunit.
Q. Is fuel system obstructed?A. Check for pinched or kinked fuel line orother obstructions in fuel system.
Q. Is fuel filter clogged?A. Clean or replace filter.
Q. Is fuel contaminated or stale?A. Fill tank with clean, fresh fuel.
Q. Is spark plug gap incorrect?A. Inspect and adjust as specified.
Q. Is ignition wiring damaged or poorly con-nected?A. Check wires for wear or breaks. Tightenall loose connections. Replace worn or bro-ken wires.
Q. Have electrical parts failed?A. Have serviced by a Yamaha dealer.
Q. Is specified fuel not being used?A. Replace fuel with specified type.
Q. Is specified engine oil not being used?A. Check and replace oil with specified type.
Q. Is thermostat faulty or clogged?A. Have serviced by a Yamaha dealer.
Q. Is air vent screw closed?A. Open the air vent screw.
Q. Is fuel pump damaged?A. Have serviced by a Yamaha dealer.
Trouble Recovery
79
Q. Is fuel joint connection incorrect?A. Connect correctly.
Q. Is heat range of spark plug incorrect?A. Inspect spark plug and replace it with rec-ommended type.
Q. Is high pressure fuel pump drive belt bro-ken?A. Have serviced by a Yamaha dealer.
Q. Is engine not responding properly to shiftlever position?A. Have serviced by a Yamaha dealer.
Engine vibrates excessively.
Q. Is propeller damaged?A. Have propeller repaired or replaced.
Q. Is propeller shaft damaged?A. Have serviced by a Yamaha dealer.
Q. Are weeds or other foreign matter tangledon propeller?A. Remove and clean propeller.
Q. Is motor mounting bolt loose?A. Tighten bolt.
Q. Is steering pivot loose or damaged?A. Tighten or have serviced by a Yamahadealer.
EMU29433
Temporary action in emergency
EMU29440
Impact damage
WARNING
EWM00870
The outboard motor can be seriouslydamaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.
If the outboard motor hits an object in the wa-ter, follow the procedure below.
1. Stop the engine immediately.2. Inspect the control system and all com-
ponents for damage. Also inspect theboat for damage.
3. Whether damage is found or not, returnto the nearest harbor slowly and careful-ly.
4. Have a Yamaha dealer inspect the out-board motor before operating it again.
EMU30681
Replacing fuse
If a fuse has blown, open the fuse holder andremove the fuse with a fuse puller. Replaceit with a spare one of the proper amperage.
WARNING
EWM00631
Substituting an incorrect fuse or a pieceof wire could allow excessive currentflow. This could cause electric system
damage and a fire hazard.
Consult your Yamaha dealer if the new fuseimmediately blows again.
Trouble Recovery
80
EMU29524
Power trim and tilt will not operate
If the engine cannot be tilted up or down withthe power trim and tilt because of a dis-charged battery or a failure with the powertrim and tilt unit, the engine can be tiltedmanually.1. Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.
2. Put the engine in the desired position,then tighten the manual valve screw byturning it clockwise.
EMU31783
Water separator-alert indicator blinks while cruising
WARNING
EWM01500
Gasoline is highly flammable, and its va-pors are flammable and explosive.
�
Do not perform this procedure on a hotor running engine. Allow the engine tocool.
�
There will be fuel in the fuel filter. Keepaway from sparks, cigarettes, flames orother sources of ignition.
�
This procedure will allow some fuel tospill. Catch fuel in a rag. Wipe up anyspilled fuel immediately.
�
The fuel filter must be reassembledcarefully with the O-ring, filter cup, andhoses in place. Improper assembly orreplacement could result in a fuel leak,which could result in a fire or explosion
hazard.
If the water separator-alert indicator on theCommand Link tachometer blinks, performthe following procedure.
1. Electrical cover2. Fuse holder3. Fuse (20 A
×
3, 30 A, 60 A
×
2)4. Spare fuse (20 A, 30 A, 60 A)5. Fuse puller
1. Fuse (20 A
×
3, 30 A, 60 A
×
2)2. Fuse puller
3 5
4
1
3
4
3
2
ZMU01903
1 2
ZMU01904
1. Manual valve screw
ZMU02403
1
Trouble Recovery
81
1. Stop the engine.2. Remove the top cowling.3. Disconnect the water detection switch
coupler.
NOTICE:
Be careful not to getany water on the water detectionswitch coupler, otherwise a malfunc-tion could occur.
[ECM01950]
4. Unscrew the filter cup from the filterhousing.
NOTICE:
Be careful not totwist the water detection switch leadwhen unscrewing the filter cup.
[ECM01960]
5. Drain the water in the filter cup by soak-ing it up with a rag.
6. Firmly screw the filter cup onto the filterhousing.
NOTICE:
Be careful not totwist the water detection switch leadwhen screwing the filter cup onto thefilter housing.
[ECM01970]
7. Connect the water detection switch cou-
pler securely until a click is heard.
8. Install the top cowling.9. Start the engine and make sure that the
water separator-alert indicator remainsoff. Have a Yamaha dealer inspect theoutboard motor after returning to port.
1. Water separator-alert indicator
1. Water detection switch coupler
1
ZMU05502
1. Filter cup2. Water detection switch lead
1. Water detection switch coupler
1
2
ZMU05501
1
ZMU05500
Trouble Recovery
82
EMU29671
Engine fails to operate
EMU29742
Low oil level alert activates
If the oil level is allowed to drop too low, thered segment will appear on the oil level indi-cator, the buzzer will sound, and enginespeed will be limited to about 2000 r/min. Ifthis happens, a reserve amount of oil can bepumped from the remote oil tank to the en-gine oil tank using the emergency switch.
WARNING
EWM01050
Be sure to stop the engine before per-
forming this procedure.
NOTICE
ECM00901
�
If the emergency switch is held up toolong, too much oil will be pumped intothe engine oil tank, overflowing it. Re-lease the switch when oil reaches theupper level line on the engine oil tank.
�
Do not use this emergency procedureunless the oil level-alert indicators are
working.
1. Remove the top cowling.2. Turn on the main switch.
3. Lift the emergency switch to pump re-serve oil into the engine oil tank from theremote oil tank.
4. After using the emergency switch, turnoff the main switch, then turn it back on.This resets the alert system to normaloperation. The yellow segment will con-tinue to be displayed on the oil level indi-cator.
5. Start the engine and return to the near-est port for more oil.
TIP:
�
The maximum reserve oil capacity is 1500cm
3
(1.6 US qt, 1.31 Imp qt).
�
The oil-feed pump will not operate if theengine is tilted up more than 35°. Put theengine in the upright position (not tilted)before using the emergency switch.
OFF
ON
ZMU01880
1. Emergency switch
1. Engine oil tank2. Remote oil tank
1
ZMU01907
1 2ZMU01908
Trouble Recovery
83
EMU33501
Treatment of submerged motor
If the outboard motor is submerged, immedi-ately take it to a Yamaha dealer. Otherwisesome corrosion may begin almost immedi-ately.
NOTICE:
Do not attempt to run theoutboard motor until it has been com-pletely inspected.
[ECM00401]
84
Consumer information
EMU35661
YAMAHA MOTOR CORPORATION, U.S.A. V MAX SERIES 2 TWO-STROKE OUTBOARD MOTOR
THREE YEAR LIMITED WARRANTY
Consumer information
85
Consumer information
86
Consumer information
87
EMU29841
IMPORTANT WARRANTY INFORMATION IF YOU USE YOUR YAMAHA OUTSIDE THE USA OR CANADA
6C9-9-18 Hyoshi 09.3.31 3:28 PM ページ 3
Printed in JapanApril 2009–0.1 × 1 ! Printed on recycled paper
6C9-9-18 Hyoshi 09.3.31 3:28 PM ページ 4