Owner’s/Installation Manual

Model: MV1055

For operational or technical assistance, after reading this manual, please call us toll free at (800) 638-3600 or visit www.magnadyne.com

10.2” Flip-down WidescreenMultimedia System

2

Driving: Be aware of road and traffic conditions. Keep the volume at a low level.

Moisture: Do not expose the product to water or excessive moisture. This could cause electrical shorts, fire or other damage.

Parking: Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the car interior a chance to cool down before starting playback.

Proper Power Supply: This product is designed to oper-ate with a 12 Volt DC, negative ground battery system.

Protecting the Disc Mechanism: Avoid inserting any for-eign objects into the slot of this player. Failure to observe this precaution may cause malfunction of this unit.

Repairs: Contact our customer service representa-tives. Do not attempt to disassemble or adjust this product yourself.

Installation: The unit should be installed in a horizontal position.

Cleaning: Use a soft cloth with some purified water to clean the screen. Do not use any cleaner or chemi-cal to clean the screen. Usually, a dry cloth will do.

Warnings:

Be careful not to drop or apply undue pressure to the front panel of monitor. If the screen cracks due to mis-use, the warranty will be voided!

The driver should neither watch the display nor operate the system while driving. Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents. Always stop the vehicle in a safe location and use the parking brake before watching the display or operating the system. In some states and countries, passengers are also pro-hibited from watching the display.

Never install the product in a location where it inter-feres with your field of vision.

Safety Information

CAUTION:THIS MOBILE DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER, THIS MOBILE DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE MOBILE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.CAUTION: FCC REGULATIONS STATE THAT ANY UNAUTHORIZED CHANGES OR MODIFICATIONS TO THIS EQUIPMENT MAY VOID THE USER’S AUTHORITY TO OPERATE IT.WARNING:• TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

• THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

This product incorporates copyright protection technol-ogy that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Magnadyne Corporation and other rights owners. Use of this copyright protection technology must be authorized by Magnadyne Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Magnadyne Corporation. Reverse engi-neering or disassembly is prohibited.

Region Management Information:This Mobile DVD Player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this Mobile DVD Player, this Mobile DVD Player cannot play this disc.

Entertainment Center Functions and Locations . . . 3-4 Remote Control Functions and Locations . . . . . . . 4System Menu Setup . . . . . . . . . . . . . . . . . . . . . 5 TFT Menu Setup . . . . . . . . . . . . . . . . . . . . . . . 6 Audio Control . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Playing a Movie Disc. . . . . . . . . . . . . . . . . . . . . 8-10Playing a MP3 File . . . . . . . . . . . . . . . . . . . . . 10-12

Auxiliary Audio/Video Inputs . . . . . . . . . . . . . . . . 12Dome Light Operation . . . . . . . . . . . . . . . . . . . . 13Headphone Operation . . . . . . . . . . . . . . . . . . 13Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Index

Use this Product Safely

3

Entertainment Center Functions and Locations

1. USB Slot: Insert a USB drive to play videos, view pictures or listen to music. Use the controls on the MV1055 or remote control to access the files on the drive.

2. SD Card Slot: Insert a SD card with the contacts facing towards the roof to play videos, view pic-tures or listen to music. Use the controls on the MV1055 or remote control to access the files on the SD card.

3. 3.5mm Auxiliary Audio/Video Input Jack: Plug-in a device with a 3.5mm audio/video input plug to play videos, view pictures or listen to music. The MV1055 will not control the device so use the con-trols on the input device to access files.

4. 3.5mm Headphone Jack: Plug-in headphones with a 3.5mm jack to hear the audio. Note: Headphone will only work when the internal speakers are activated. (see page 7)

5. Disc Slot: Insert a disc into the slot with label facing up.

6. Dome Lights

7. IR Repeater: The audio signal is converted to an infrared light and transmitted to the headphones.

8. Mode Button: Press to select between sources: DVD, AV1 (internal audio/video RCA inputs) or AV2 (external 3.5mm audio/video input jack).

9. Dome Light Door Button: When the vehicle’s door is open the dome lights automatically turn on. To turn off the dome lights when the vehicle’s door is open press the button.

10. System Menu Button: Press the button to access the TFT Menu Setup features.

11. Remote Control Sensor: Point the remote control at this area to remotely control the MV1055.

12. Dome Light Button: Press the button to turn on or off the dome light.

13. Disc Eject/TFT Menu Adjustment Button: Press the button to eject the disc from the unit. Note: For TFT Menu Setup button function refer to the TFT Menu Setup section of this manual for more information. (Page 6)

1 2 3 4

6

7

MODE

5

118 13

9 10 12

141516

4

Entertainment Center Functions and Locations (continued)

14. Disc Stop/TFT Menu Adjustment Button: Press the button to pre-stop disc play. Press the play button to resume play where the disc play was stopped. Press the button twice to stop disc play then press the play button to start play from the beginning of the disc. Note: For TFT Menu Setup button function refer to the TFT Menu Setup section of this manual for more information. (Page 6)

15. Power Button: Press this button to turn the entertainment center on or off.

16. Play/Pause Button: Press the button to pause play, press again to resume play.

Remote Control Functions and Locations

Note: Install the battery before operating the remote.

1. Power Button: Press this button to turn the entertainment center on or off.

2. TFT Menu Button: Press to access the TFT Menu Setup features of the MV1055.

3. Channel - and + Buttons: No function.

4. Mode Button (AV/TV DVD): Press to select between sources: DVD, AV1 (internal audio/video RCA inputs) or AV2 (external 3.5mm audio/video input jack).

5. Auto Button: No function.

6. Numeric Key Pad

7. Eject Button : Press to eject the disc.

8. Play/Pause Button: Press the button to pause play, press again to resume play.

9. Backwards and Forward Play Buttons: Use these buttons to change the play speed to x2, x4, x8 or x20 either backwards ( ) or forwards ( ).

10. DVD Menu Button: Press to access the DVD’s menu features.

11. Navigation Buttons: Press to navigate in menus up, down, left or right.

12. Enter Button: Confirms the selected item.

13. Return Button: Returns to previous menu in MP3 mode.

14. Disc, SD Card and USB Mode Selector: Press to select between DISC (DVD/CD), CARD (SD card) or USB (USB drive) mode.

15. DVD Audio Button (R/L): Changes the language on multi-language movie disc.

16. Volume Buttons: Press the VOL + to increase the volume or press the VOL - to decrease the volume.

17. Mute Button: Mutes the volume.

18. Repeat Button: Press to repeat chapters, titles, tracks and discs.

19. Stop Button: Press to pre-stop disc play. Press the play button to resume play where the disc play was stopped. Press the button twice to stop disc play then press the play button to resume play from the beginning of the disc.

20. Next and Previous Selection: In the movie mode pressing these buttons will select the next or pre-vious chapter. In the music mode pressing these buttons will select next or previous track/file.

21. Setup Button: Access the System Setup menus.

22. Display Button (DISP): Displays source information.

23. Program Button: Programs play sequence.

24. Subtitle Button: Accesses movie disc’s subtitle languages.

25. Title Button: Displays title information if available.

26. Zoom Button: Enlarges or reduces the size of picture.

27. A-B Button: Record a selected section of a movie or music to play repeatedly.

TFTMENU CH+ CH-

AV/TVDVD

AUTO

1 2 3 4

5 6 7 8

9 0 +10

STOP REPEAT

DVDMENU DISP SETUP

ENTER PROGRAM

RETURN TITL E SUBTITLE

SDUSB

R/L A-B ZOOM

VOL+ VOL-

1 2 3

45

6

78

9

10

11

13

1514

12

16

17

1819

20

2122

2425

23

2627

5

System Menu Setup

System Menu Setup:

1. Press the SETUP button on remote control to enter the system menu setup screen.

2. Use the , , and buttons to select the menu item you want to change.

3. Once the menu item is selected, press the but-ton to activate options for that menu item.

4. Use the and buttons to select the option you want then press the ENTER button.

5. Press the SETUP button to exit the system menu setup screen.

System Menu Setup Items:

TV SYSTEM PAL NTSC AUTO

POWER RESUME (The disc play will resume play-ing when the power was turned off )

ON OFF

AUTO PLAY SETTING (Disc auto play) ON OFF

TV TYPE 4:3 PS 4:3 LB 16:9

PASSWORD (Password to lock Ratings menu) _ _ _ _

1. Enter the password “0000” and press the ENTER button. The unlock symbol will appear next to _ _ _ _.

2. Go to the Rating sub-menu and make the neces-sary change.

3. Return to the Password sub-menu and enter “0000” password and press the ENTER button. The lock symbol will appear next to _ _ _ _. The system is now password protected.

RATING (For movies) 1 KID SAFE 2 G 3 PG 4 PG13 5 PG-R 6 R 7 NC-17 8 ADULT

DEFAULT (Return all setting to default settings) RESTORE

Language Setup Items:

OSD LANGUAGE (On Screen Display language) ENGLISH CHINESE GERMAN SPANISH FRENCH PORTUGUESE RUSSIAN

AUDIO LANG CHINESE ENGLISH RUSSIAN SPANISH GERMAN PORTUGUESE

SUBTITLE LANG CHINESE ENGLISH RUSSIAN SPANISH GERMAN PORTUGUESE

MENU LANG CHINESE ENGLISH RUSSIAN SPANISH GERMAN PORTUGUESE

DVDMENU DISP SETUP

ENTER PROGRAM

RETURN TITL E SUBTITLE

TV SYSTEMPOWER RESUMEAUTO PLAYTV TYPEPASSWORDRATINGDEFAULT

6

TFT Menu Setup

TFT Menu Setup:

1. Press the button on the MV1055 to enter the TFT Menu Setup screen.

2. When the menu appears on the screen press the button to select the menu item: Picture, Volume, Option, System and Clock.

3. Press the MODE button to select the sub-menu items.

4. Use the and buttons to adjust the sub-menu item.

5. After approximately 10 seconds of no button activ-ity the TFT Menu Setup screen will disappear.

Menu Item

Sub-menuItems

TFT Menu Setup Items:

PICTURE (Adjust the picture quality) BRIGHTNESS CONTRAST COLOR RESET

VOLUME VOLUME IR (Infrared audio signal to wireless headphones) (Select IR-A when using MovieVision headphones)

FM (Transmits audio over a FM radio station to vehicle’s radio)Note: For MV1055 internal speakers and 3.5mm headphone jack to operate both IR and FM sub-menus need to be set in the OFF position.

OPTION ENGLISH (Menu Language) ZOOM 16:9 or 4:3

SYSTEM S-COLOR (No selection available)

CLOCK Note: Clock is a 24 hour clock. SLEEP (Select a time for the sleep timer) TIME (Use the to adjust the hours) (Use the to adjust the minutes) OFF-TIME: (Use to turn OFF the system at a predetermined time) ON-TIME: (Use to turn ON the system at a predetermined time)

Selecting Menu Items

Selecting Sub-Menu Items

Adjusting Sub-Menu Items

MODE

7

Audio Control

Playing Audio Through IR Headphones:

In the TFT Menu under the Volume sub-menu make sure the IR setting is IR-A. (IR-A setting is for MovieVision wireless headphone, HP-400)

Note: Audio will not play through the MV1055 internal speakers or the 3.5mm headphone jack.

IR-A

Playing Audio Through the Vehicle’s Radio:

1. In the TFT Menu under the Volume sub-menu make sure the FM setting is on one of the avail-able radio frequencies not presently being used by a radio station. (87.7, 87.9, 88.1, 88.3, 88.5, 88.7,88.9, 106.7, 107.1 or 107.5MHz)

2. Tune in the vehicle’s FM radio to the frequency selected in the FM settings sub-menu.

Note: Audio will not play through the MV1055 internal speakers or the 3.5mm headphone jack.

RadioFrequency

Set toOff

Internal Speakers

3.5mmHeadphone Jack

Playing Audio Through the System’s Internal Speakers or 3.5mm Headphone Jack:

1. In the TFT Menu under the Volume sub-menu make sure the IR and FM setting are set to OFF.

2. Use the volume control on the remote to adjust the volume level.

Note 1: When a headphone is plugged into the 3.5mm jack the internal speakers will be muted.

Note 2: Audio will not play through the vehicle’s radio or through the wireless headphones.

8

Playing a Movie Disc

Inserting a Disc:

1. Press the power button to turn the unit on.

2. Insert a disc into the player with the label on the disc facing upward.

3. The disc will automatically load and start playing.

Ejecting the Disc:

Press the eject button on the system to eject the disc. You can also use the eject button on the remote control to eject the disc.

Pausing the Disc:

Press the pause button on the system pause disc play. Press the button again to resume disc play. You can also use the pause button on the remote control

MODE

Stopping the Disc:

Press the button to pre-stop disc play. Press the play button to resume play where the disc play was stopped. Press the button twice to stop disc play then press the play button to start play from the beginning of the disc.

Accessing the DVD Menu Screen:

Press the DVD/MENU button to access the DVD menu screen. Use the navigation buttons , , and to select the desired menu option. Press the ENTER button to confirm your selection.

DVDMENU DISP SETUP

ENTER PROGRAM

Label Facing Up

Mode Selection:

To select the DVD source press the MODE button until “DVD” appears on the screen. The system will automatically start to play the DVD. MODE

9

Backward and Forward Play Buttons:

To play the disc backwards press the button and the disc will play in reverse at 2 times normal playback (x2), continually press the button to select x4, x8 or x20 reverse play. To play the disc fast forward press the button and the disc will play at 2 times normal playback (x2), continually press the button to select x4, x8 or x20 fast forward play. Press the pause button at any time to stop fast reverse or fast forward play.

STOP REPEAT

DVDMENU DISP SETUP

Playing a Movie Disc (continued)

Next or Previous Chapter Selection:

To select the next chapter of the movie press the button. To select the previous chapter press

the button.

STOP REPEAT

DVDMENU DISP SETUP

Display Button:

Press the DISP button during movie play to display the following information in this order for most discs:Title Elapse, Title Remain, Chapter Elapse, Chapter Remain and Display Off.

Subtitle Language:Press the SUBTITLE button during playback. Each time the button is pressed, the subtitle language changes. The selection of subtitle appears at the top of the screen. Notes:1. Some discs may contain only one subtitle language.2. Depending on the disc, the number of subtitle

languages may be different.

DVDMENU DISP SETUP

ENTER PROGRAM

ENTER PROGRAM

RETURN TITL E SUBTITLE

SDUSB

R/L A-B ZOOM

Audio Language:Press the R/L button during playback. Each time the button is pressed, the audio language changes. The selection of audio appears at the top of the screen.

RETURN TITL E SUBTITLE

SDUSB

R/L A-B ZOOM

Direct Chapter Selection:

To directly select a chapter use the numeric pad on the remote control to enter the number of the chapter you want to select. For example: If you want to go to chapter 7 press the number 7 on the remote control the unit will automatically switch to chapter 7.

1 2 3 4

5 6 7 8

9 0 +10

10

Playing a MP3 File

Inserting a Disc:

1. Press the power button to turn the unit on.

2. Insert a disc into the player with the label on the disc facing upward.

3. The disc will automatically load and start playing.Note: To remove the disc press the eject button.

Inserting a USB Drive:

1. Press the power button to turn the unit on.

2. Insert a USB drive into the USB slot. Note: If the USB drive does not fit, flip it over and try again.

3. The USB drive will automatically load and start playing.

Note: To remove the USB drive pull the drive out of the slot.

Inserting a USB Drive:

1. Press the power button to turn the unit on.

2. Insert a SD Card into the USB card slot with the notch facing to the left until it clicks into place. Note: If the SD card does not fit, flip it over and try again.

3. The SD card will automatically load and start playing.

Note: To remove the SD card press on the card until it clicks, then remove the card.

Playing a Movie Disc (continued)

Repeat Play Selection:To record a section of the movie to play repeatedly press the A-B button once, “Repeat A-” appears on the screen. Press the A-B button again to con-cluded your selection. The section of the movie will play continually. Press the A-B button again to cancel this feature.

Zoom Selection:1. Press the ZOOM button during playback. Each

time the button is pressed, the magnification increment changes in the following order: 2X, 3X, 4X, 1/2, 1/3, 1/4 then Off.

2. Use the navigation buttons , , and to move the image on the screen.

RETURN TITL E SUBTITLE

SDUSB

R/L A-B ZOOM

RETURN TITL E SUBTITLE

SDUSB

R/L A-B ZOOM

Label Facing Up

Notch

11

Playing a MP3 File (continued)

MP3 Interface Screen:

The MP3 media (Disc, USB drive or SD card) con-tains folder(s) with files inside the folders. These files can include music tracks, photos and/or videos (compatible MPEG1, MPEG2 and DivX files). Use the icons at the bottom of the screen to select which type of files you want to access. Note: If an icon can not be select the unit has deter-mine that kind of files is not accessible.

Mode Selection:1. Select the DVD source by pressing the MODE

button until “DVD” appears on the screen.2. Press the SD/USB button on the remote control.

A screen will appear with 3 selections: DISC, CARD and USB.

3. Use the or button on the remote control to select the desired mode.

4. Press the ENTER button to confirm your selection.

MODE

Folders Files

Music Photos Video

File Selection:1. Use the , , and buttons to navigate

both the folders and file menus.2. When the correct file has been located press the

ENTER button on the remote control.

Pausing Play:

Press the pause button on the system pause play. Press the button again to resume play. You can also use the pause button on the remote control

MODE

Stopping Play:

Press the button to pre-stop play. Press the play button to resume play where the play was stopped. Press the button twice to stop play then press the play button to start play from the beginning of the file.

Next or Previous File Selection:

To select the next file of the movie press the button. To select the previous file press the button.

DVDMENU DISP SETUP

ENTER PROGRAM

RETURN TITL E SUBTITLE

STOP REPEAT

DVDMENU DISP SETUP

12

Playing a MP3 File (continued)

File Repeat Function:

Press the REPEAT button to select from the follow-ing repeat functions: REP 1 = Repeat one file continuously. REP DIR = Repeat every file in the directory continuously. REP ALL = Continuously repeat every file. REP OFF = Repeat function is off.

Direct File Selection:

To directly select a file use the numeric pad on the remote control to enter the number of the file you want to select. For example: If you want to go to file 7 press the number 7 on the remote control the unit will automatically switch to file 7.

1 2 3 4

5 6 7 8

9 0 +10

9 0 +10

STOP REPEAT

Program Function:1. Press the PROGRAM button on the remote control

to enter the programming screen. 2. Under the “T” column enter the folder number. 3. Under the “C” column enter the file number. 4. When you have finish programming your play list

use the navigation buttons , , and to highlight the “PLAY” button at the bottom of the screen. Then press the ENTER button to start your programmed play list .

DVDMENU DISP SETUP

ENTER PROGRAM

RETURN TITL E SUBTITLE

Auxiliary Audio/Video Inputs

Internal Auxiliary RCA Inputs (AV1):1. A device must be connected to the RCA connectors

coming from the MV1055. 2. Press the MODE button until “AV1” appears on the

screen. 3. Use the controls on the connected device to control

the playback.

3.5mm Auxiliary Input (AV2):1. Plug in a device with a 3.5mm audio/video output

into the MV1055. 2. Press the MODE button until “AV2” appears on the

screen. 3. Use the controls on the connected device to control

the playback.

MODE

MODE

13

Dome Lights Operation

Dome Light Switch:Press the dome light button to turn on and off the dome lights in the MV1055.

MODE

Dome Light Door Switch:When the vehicle’s door is open the dome light comes on automatically. To turn off the dome lights when the door is open press the dome light door button to turn the dome lights off.

IR RepeaterThe audio signal is converted to an infrared light and transmitted to the headphones (purchased separately). Refer to the owner’s manual included with the headphone on how to adjust the volume to suit the listener’s taste.Note: For optimal performance a clear line of sight is required between the MV1055 IR repeater and the headphones.

Headphone Operation

IR Repeater

HP-400 Headphones(Purchased Separately)

Wiring

14

Wire Harness:Red Wire: Connect the red wire to a +12 volt power wire that is turned on and off by the position of the ignition key.

Black Wire: Connect the black wire to the chassis of the vehicle using a ring terminal and self-tapping screw or bolt.

Audio/Video RCA Connectors:Audio/Video Output: Connect to an external monitor. Audio/Video Input: Connect to an external source, for example a DVD player, video camera, video game, etc.

Wire Leads:Yellow Wire: Connect the yellow wire to a constant +12 volt wire that is NOT turned on and off by the position of the ignition key.

Black Wire [Negative Door Lock Trigger (-)]: Connect the black wire to the common trigger wire coming from all door pin switches.Note: If the blue wire (positive door lock trigger) is connected the black wire has no connection.

Blue Wire [Positive Door Lock Trigger (+)]: Connect the blue wire to the common trigger wire coming from all door pin switches.Note: If the black wire (negaitve door lock trigger) is connected the blue wire has no connection.

Green Wire (FM Transmitter Antenna): Do not connect this wire. Lay this wire across the of the roof making sure is does not come into contact with any metal parts of the roof.

2A Fuse

Filter &Fuse Box

Installation

15

1. Mount the Bracket:Carefully plan exactly where to mount the bracket. Also plan where the wires are going to run once the bracket is mounted to the ceiling of the vehicle.

2. Mount the Main Unit:Feed the wires through the opening in the bracket. When attaching the main unit to the bracket with the supplied screws make sure no wires or connec-tors get trapped between the mounting bracket and main unit. Note: Damage may occur if connectors are force up into the main unit.

3. Install the Trim Cover:Snap the trim cover on to the main unit.

Bracket

BracketMountingScrews(not supplied)

Main Unit

Main UnitScrewsand Washers(supplied)

TrimCover

Vehicle’s RoofSupports

MV1055-UM Rev. C 10-3-15© Copyright 2015 Magnadyne Corporation

ONE (1) YEAR LIMITED WARRANTY

Magnadyne Corporation or its authorized agents will within 1 year from the date of sale to you, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materi-als or workmanship, when properly connected and operating on the correct power requirements designated for the specific product. This warranty and Magnadyne Corporation or its authorized agents obligations hereunder do not apply where the product was; damaged while in the posses-sion of the consumer, subjected to unreasonable or This warranty does not cover the cabinet appearance items or accessories used in connection with this product, or any damage to recording or recording tape, or any damage to the products resulting from improper installation, alteration, accident, misuse, abuse or acts of nature. MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND 1 YEAR FROM THE DATE OF SALE. This warranty extends only to the original purchaser of the product and is not transferable.Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights and you may have other rights that vary from state to state.Defective merchandise should be returned to the original point of purchase or secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220. Return Authorization must be obtained before sending, or merchandise may be refused.

Warranty