OUR QUALITY PACKAGE - Entrepot
Transcript of OUR QUALITY PACKAGE - Entrepot
We make our products work harder for you
OUR QUALITY PACKAGEEM-2020
Our Quality Package
Ratchet Wrench 3Impact Wrench 3-5Screw Driver and Drill 6Light & Handy Die Grinder 7Die Grinder & Straight Grinder 7Angle Grinder 8-9Sander 10Baby Hammer 11Scaling Hammer 11Needle Scaler & Flux Chipper 11
Chipping Hammer 12Sand Rammer and Tamper 12Digger and Breaker 13Concrete Breaker 14Rock Drill & Accessories 15Earth Auger Drill & Accessories 16Air Winch / Air Mucking Winch 17Air Chain Hoist 18-19Air Powered Balancer 18Air Operated Trolley 18
TOKU Air Tools
Product Highlights 1
Air Saw & File 20Air Plate Shears 20
Needle Scaler 30Chisel Scaler 31Pole Scabbler 31Scaling Hammer 32Multi Heads Scaling Machine 33Trident Neptune 34Floor Planer 35Hand-held scarifier 36Hydraflex - Water Jet 37Long Reach Scaler 37
EM2 PRODUCTSBelt Sander 22Hybrid Ratchet Wrench 22Needle/Chisel Scaler 22 Industrial Air Tools 23Abrasives 44Industrial Brushes 45
Operations & Maintenance Instructions for Air Tools 2
Hydraulic Drilling Mast 25SAN-EI
Air Winch 26
MORATH
MUROMOTO
STAR LIFTKET Electric Winch 27Electric Chain Hoist 28-29
TRELAWNY ATA
Turbine & Pencil Grinder 38Angle Head Die Grinder & Sander 38Die Grinder 39Angle Sander & Grinder 40Belt Sander 40New Products 41
Cut Selection Guide 42Handy Burr Set 42Tungsten Carbide Burr 43
PROCUT
Baby Electric Winch 25
TKK
LESSMANN 46
ZECA Air Hose Reel 48Cable Reel with Lamp 49Retractable Cable Reel 49Valve Grinder 50Rechargeable LED Lamp 50 Spring Balancers 50Garage Tools 51
JOPLA 52
YOSHIDA 53
AMPLA 47
ALFRA 54-55
EISENBLATTER 56-57
FAR 58 AERSERVICE 59
DARDA 68-69HYCON 66-67
Chisels & Moil Points 60 SMC & DIXON 61
AIRBOSS 62 APAC 63
DU-PAS 65 TORERO 64
BIG STONEPneumatic Leg Drill 24
NKS 21
Highlights
1
AIR VACUUM GUN KIT - 32NV043• Comfortable Composite Gun Body with Vacuum/Blow 2-way function• Light-weight design, easy for operation• Designed to get in tight quarters as it consists of a 12” long flexible
hose and extension tube for clearing dust at corners
• AT-4337A - 1/2” ANGLE IMPACT WRENCH• Powerful Torque - 312Nm• Easy Access in confined areas - 88mm width• Lightweight - only 1.4kg
AT-4337ASquare Drive 1/2”
Speed 9,000 rpm
Length 247 mm
Max Torque 312 Nm
Working Torque 224 Nm
Avg. Air Cons 0.11 m3/min
Weight 1.4 kg
Air Inlet 1/4”
CONCRETE CRUSHER - CC340
Specifications I Concrete Crusher CC340 Length x Width x Height 877 x 715 x 334 mm
Jaw opening 343 mm
Total weight 150kg
Recommended carrier weight 1.5-2.7 t
Minimum Connection pressure 16.5MPa (165bar)
Maximum Connection pressure 25MPa (250bar)
Operating pressure 47MPa (470bar)
Maximum Oil flow 100 I/min
Maximum Crushing force 360kN (36.7t)
Maximum Cutting force 950kN (97t)
Maximum Cutting capacity ø 30 mm
• Rapid demolition in confined areas• Low noise• Low dust• Low vibration
2
OPERATION & MAINTENANCE INSTRUCTION FOR AIR TOOLS
Proper operating procedure and regular maintenance greatly affect the performance, safety and durability of air tools. The following instruction must be complied before operating the air tools to ensure proper performance, durability and safety.
Thank you for your support.
Air tools are designed to be operated at air pressure of 5 to 7 kg/cm2 at the air inlet during operation.
Air compressor distribution capacity should be 20% more than the recommended air consumption of the tool specification to compensate for air loss through piping system. In general, a 10HP compressor can deliver 1m3/min of air at 6kg/cm2
AIR COMPRESSORLubrication is very important for operation of air tools. All air tools that are sold by TOKU are tested before delivery.
However, if an inoperable situation or poor performance is experienced, please be sure to clean off the anti-corrosive oil by putting a small volume of the lubricant (SAE#10) in the tool. Restart at slow speed gradually.
LUBRICATION
Dust and moisture will affect the performance of air tools, therefore, an air treatment system, Filter-Regulator Lubricator (see page 61) should always be equipped in the piping.
The oil in the lubricator should also be checked regularly.
DUST-PROOF & ANTI-CORROSION
Air tool parts are precision-machined items. Throwing, dropping or rough handling is strictly prohibited. Periodical inspection will increase the durability performance and efficiency of the air tool. Check air line regularly to ensure clean air is supplied to the air tools.
MAINTENANCE & PERIODICAL INSPECTION
Before storing your air tools for an extended period of time, carefully clean, lubricate and place them in an area where they would not collect dust or moisture.
It is generally a good idea to save the original packaging for such a situation.
Take the necessary precautions to protect yourself from possible injury.
ALWAYS USE SAFETY GOGGLES or face shield. Be mindful of loose clothing – ties, short sleeves, jackets, etc –that could become entangled with a tool
Our Quality PackageAll products in our Quality Package are warranted to be free from defects in material and workmanship for twelve (12) months from the date of purchase. The warranty applies only to the products purchased from us or other authorized distributors and will also not apply to products that have been abused, misused, modified or repaired by unauthorized Service Centres.
There are no warranties expressed or implied, and when we shall not be liable for any damages, costs or expenses resulting from the use of our product except only the cost or expenses of repair or replacement as described above.
LIMITED WARRANTY
DisclaimerThe information displayed in this catalogue were from suppliers and other relevant sources. Any reproduction whether in part or whole is not allowed, unless with our prior written consent. We shall not be liable for all and/or any loss (whether suffered directly or indirectly) arising from any reliance upon information displayed in this catalogue. As products are constantly improved, designs and specifications are subjected to change without prior notice or any obligations.
RATCHET WRENCH
IMPACT WRENCH
• Compact and powerful• Rubber covered ratchet head• Durable ratchet head for long life• Forward and reverse switch• Ideal for confined work space
MR-2207C - 1⁄4” MR-2209C - 3⁄8”
MR-2310B - 3⁄8” MR-2410B - 1⁄2”
MI-1310S - 3⁄8” MI-1311B - 3⁄8”
ModelSquare Drive (in)
Bolt Size (mm)
Torque Range (kg.m)
Max Torque (kg.m)
Net Weight
(kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons (m3/min)
Air Inlet (pt)
Hose Size (in)
MR-2207C 1⁄4 8 0.6-2.8 5.5 0.53 165 250 0.35 1⁄4 1⁄4
MR-2209C 3⁄8 8 0.6-2.8 5.6 0.53 165 250 0.35 1⁄4 1⁄4
MR-2310B 3⁄8 10 1.4-7.0 8.3 1.13 254 180 0.45 1⁄4 1⁄4
MR-2410B 1⁄2 10 1.4-7.0 8.3 1.13 254 180 0.45 1⁄4 1⁄4
ModelSquare Drive (in)
Bolt Size (mm)
Torque Range (kg.m)
Max Torque (kg.m)
Net Weight
(kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
MI-1310S 3⁄8 10 1.0 - 9.0 12.0 0.91 177 12,500 0.30 1⁄4 3⁄8
MI-1311B 3⁄8 10 3.0 - 7.0 10.0 1.30 150 7,000 0.40 1⁄4 1⁄4
TW-6S 3⁄8 8 4.0-13.0 17.0 1.31 207 8,000 0.19 1⁄4 3⁄8
• Small body for easy grip handle and yet powerful• Quick run down capacity• Durable ratchet head for long life• Forward and reverse switch• Ideal for confined work space
• One-hammer clutch mechanism• Butterfly throttle valve system allows easy
forward and reverse rotation with one hand• 360° air inlet swivel for flexibility• Vibration Level: 2.8m/s2
• Sound Pressure Level: 87dBA• Pressure: 85 PSI
• One-hammer clutch mechanism• Light weight & well-balanced weight
distribution for easy handling• 4-Position regulator• Ideal for general repair on light
vehicle, e.g. Motorcycle.
1/4” to 1/2” square drive
3/8” square drive
Specifications: Air Pressure 6kg/cm2 Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
Specifications: Air Pressure 6kg/cm2 Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
http://www.toku-net.co.jp/enMade in Japan
83
35mm 35mm
45mm 45mm
All Ratchet Wrench, Impact Wrench and Screw Driver are Forward and Reverse Actions.
Please refer to page 11 for Hybrid Ratchet Wrench
TOKU’s Pin-Less Clutch Mechanism
Pin-less clutch requires less parts and greatly reduces vibration, and generates constantly higher power
TOKU’s Twin Hammer Clutch Mechanism• Toku twin hammer provides maximum performance,
balance impacts and power output. • Less wasted energy and simplified maintenance. • Cold forged hammer for high durability.
TW-6S - 3⁄8”• Double Hammer mechanism• Built-in torque regulator• Low vibration
L
L
L L
IMPACT WRENCH 1/2” to 1” square drive
MI-16M - 1⁄2” MI-17M - 1⁄2” • Twin-hammer clutch mechanism• Elastomer handle grip• 4-Position regulator• Ideal for car repair and assembly work
• Twin-hammer clutch mechanism• Tease throttle for precise control• Balance-body weight distribution• 4-Position regulator with high reverse power
MI-17C - 1⁄2”
MI-20P - 3⁄4”
MI-2500P - 3⁄4” & 1”
• Twin Hammer Clutch : Lighter weight & higher power
• Tease throttle for precise control• 360° free rotating exhaust• Ergonomic design : Reduced operator’s fatigue• 4-Position regulator• One hand easy reverse switch
• Pin-less clutch mechanism• 2-step throttle for precise control• Elastomer side handle grip• 360° free rotating exhaust• 4-Position regulator
MI-1625B 3⁄4”
MI-3800P - 1” MI-5000P - 1”
• Pin-clutch mechanism• Balance-body weight distribution• Twin power regulator
• Pin-less clutch mechanism• 2-step throttle for precise control• Elastomer side handle grip• 360° free rotating exhaust• 4-Position regulator
ModelSquare Drive (in)
Bolt Size (mm)
Torque Range (kg.m)
Max Torque (kg.m)
Net Weight
(kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
Shank Size Length - L
(mm)MI-16M 1⁄2 16 15-25 33 1.5 170 7,200 0.4 1⁄4 3⁄8 -
MI-17M 1⁄2 16 25-45 R55 L60 2.5 179 5,500 0.5 1⁄4 3⁄8 -
MI-17ML 1⁄2 16 25-45 R55 L60 2.6 232 5,500 0.5 1⁄4 3⁄8 73
MI-17C 1⁄2 16 26-56 R65 L70 1.8 181 R8500 L8800 1.0 1⁄4 3⁄8 50.8
MI-20P 3⁄4 22 40-80 100 3.9 220 5,000 0.7 3⁄8 3⁄8 -
MI-20PL 3⁄4 22 40-80 100 4.6 340 5,000 0.7 3⁄8 3⁄8 150
MI-1625B 3⁄4 22 28-117 129 5.6 245 5,000 0.7 1⁄4 1⁄2 -
MI-2500P 3⁄4 25 50-110 130 8.2 265 5,300 0.7 3⁄8 1⁄2 -
MI-2500PL 3⁄4 25 50-110 130 9.3 386 5,300 0.7 3⁄8 1⁄2 150
MI-2500P 1 25 50-110 130 8.2 265 5,300 0.7 3⁄8 1⁄2 -
MI-2500PL 1 25 50-110 130 9.3 386 5,300 0.7 3⁄8 1⁄2 150
MI-3800P 1 38 50-150 200 9.5 276 4,700 1.0 1⁄2 1⁄2 -
MI-3800PL 1 38 50-150 200 10.8 430 4,700 1.0 1⁄2 1⁄2 200
MI-5000P 1 50 50-220 270 13.9 310 3,700 1.0 1⁄2 1⁄2 -
MI-5000PL 1 50 50-220 270 16.2 520 3,700 1.0 1⁄2 1⁄2 230
Specifications: Air Pressure 6kg/cm2 Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
http://www.toku-net.co.jp/enMade in Japan
4
MI-2500PL MI-3800PL MI-5000PL
MI-20PL
Long shank
MI-17ML
Long shank
Long shank Long shank
• Twin-hammer clutch mechanism• Lightweight for comfortable work• Balance-body weight distribution• 3-step forward, 2 steps reverse regulator
LL
L
IMPACT WRENCH 3/4” to 1½” square drive
• Pin-clutch mechanism• Balance-body weight distribution• Twin power regulator
MI-2500GSMI-3800GS
MI-2500GL - 3⁄4” & 1”MI-3800GL - 1”• Pin-less clutch mechanism• 2-step throttle for precise control• Elastomer side handle grip• 4-Position regulator• Available in ¾” and 1”
MI-5000GL - 1”• Pin-less clutch mechanism• 2-step throttle for precise control• Elastomer side handle grip• 4-Position regulator
ModelSquare Drive (in)
Bolt Size (mm)
Torque Range (kg.m)
Max Torque (kg.m)
Net Weight
(kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
Shank Size - L (mm)
MI-2500GS 3⁄4 25 50-110 130 8.2 341 5,300 0.7 3⁄8 1⁄2 -
MI-2500GL 3⁄4 25 50-110 130 9.3 459 5,300 0.7 3⁄8 1⁄2 150
MI-2500GS 1 25 50-110 130 8.5 341 5,300 0.7 3⁄8 1⁄2 -
MI-2500GL 1 25 50-110 130 8.2 341 5,300 0.7 3⁄8 1⁄2 150
MI-3800GS 1 38 50-150 200 9.5 335 4,700 1.0 1⁄2 1⁄2 -
MI-3800GL 1 38 50-150 200 10.2 504 4,700 1.0 1⁄2 1⁄2 200
MI-38GL 1 38 50-110 180 7.9 498 3,700 0.7 1⁄2 1⁄2 200
MI-42GS 1 42 50-180 260 10.2 370 3,900 1.0 1⁄2 1⁄2 -
MI-42GL 1 42 50-180 260 10.6 519 3,900 1.0 1⁄2 1⁄2 200
MI-5000GS 1 50 50-220 270 14.3 460 3,700 1.0 1⁄2 1⁄2 -
MI-5000GL 1 50 50-220 270 16.0 594 3,700 1.0 1⁄2 1⁄2 230
MI-5500 11⁄2 55 150-428 560 18.1 520 2,800 0.9 1⁄2 1⁄2 -
MI-38GL - 1” MI-42GL - 1”• Twin-hammer clutch mechanism• 2-step throttle for precise control• Elastomer side handle grip• 4-Position regulator
MI-5500 - 1 1⁄2” • Pin-clutch mechanism• Powerful for extra heavy duty work
Specifications: Air Pressure 6kg/cm2 Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
http://www.toku-net.co.jp/enMade in Japan
5
Short shank
Short shank MI-5000GS
L
Short shank
MI-42GS
SCREW DRIVER Compact & Powerful
DRILL
MV-6216B MV-6226B - Pistol Grip MI-12D• Compact and easy to use• Adjustable torque – clutch type• Ideal for light assembly industries
• Twin-hammer clutch mechanism• Tease throttle for precise control• Balance-body weight distribution• 4-Position regulator with high reverse power
• Twin-Hammer Clutch• Tease Throttle for precise control• One handed easy reverse switch
TW-6SD MID-60• Double Hammer mechanism• Built-in torque regulator• Low vibration
• Compact, light weight & powerful• Double-Dog Hammer mechanism for power
vs weight• Ideal for all kinds of assembly jobs
Model Driver Chuck Hex. (in)
Bolt Size (mm)
Max Torque (kg.m)
Net Weight (kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
MV-6216B 1⁄4 6 0.9 1.20 250 1,800 0.42 1⁄4 1⁄4MV-6226B 1⁄4 6 1.2 1.30 205 1,800 0.60 1⁄4 1⁄4TW-6SD 1⁄4 8 17.0 1.50 215 6,750 0.20 1⁄4 3⁄8MID-60 1⁄4 6 9.8 0.80 181 10,800 0.32 1⁄4 3⁄8MI-12D 1⁄4 12 12.0 1.20 154 9,500 0.40 1⁄4 1⁄4
Model Driver Chuck (mm)
Driver chuck (in)
Net Weight (kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons (m3/min)
Air Inlet (pt)
Hose Size (in)
MD-10L 10 3⁄8 0.9 130 2,300 0.50 1⁄4 1⁄4MD-3310B 10 3⁄8 1.0 165 2,400 0.47 1⁄4 1⁄4MD-3311B 10 3⁄8 1.1 200 2,000 0.58 1⁄4 1⁄4MD-3312B 10 3⁄8 1.2 208 1,200 0.36 1⁄4 1⁄4MD-3413B 13 1⁄2 1.6 220 500 0.47 1⁄4 1⁄4
Specifications: Air Pressure 6kg/cm2 Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
MD-10L MD-3310B MD-3311B• Industrial tool – high torque• Tease throttle for better control• Handle exhaust • Forward action
• Handle exhaust• Forward action
• Handle exhaust• Reversible-forward and reverse
MD-3413B
MD-3312B
• Side support handle for better control• Double gear reduction system for high cutting torque -
can be used as a paint mixer• Reversible-forward and reverse
• Compact and light weight• Tease throttle for precise control• Rear exhaust• Forward and reverse action
Specifications: Air Pressure 6kg/cm2
http://www.toku-net.co.jp/enMade in Japan
6
13 6.35
90mm
80mm
Optional: MD-3413B can be used as a mixer
LIGHT & HANDY DIE GRINDER
DIE GRINDER & STRAIGHT GRINDER
General Maintenance
Industrial Duty
MG-7206B - rear exhaust MG-7236B - front exhaust
MG-7204B - front exhaust MG-20 - front exhaust
• Safety Lever Throttle• High Speed, low vibration• Compact, light and handy• Ideal for grinding and deburring• 6mm Collet (Standard)• Optional ¼”or 3mm collect on request
Model Collet Size (mm) Wheel Size (mm)
Net Weight (kg)
OA Length (mm)
Free Speed (rpm)
Avg. Air Cons (m3/min) Air Inlet (pt) Hose
Size (in)MG-7206B 6 (3 & 1⁄4" Optional) 25 0.6 146 22,000 0.5 1⁄4 3⁄8MG-20 6 (3 & 1⁄4” Optional) 25 0.6 139 22,000 0.6 1⁄4 3⁄8MG-7236B 6 (3 & 1⁄4" Optional) 25 0.4 123 18,000 0.38 1⁄4 3⁄8MG-7204B 6 (3 & 1⁄4” Optional) 25 0.4 120 25,000 0.38 1⁄4 3⁄8
Specifications: Air Pressure 6kg/cm2
Model Wheel Size (mm)
Collet Size (mm)
Max Cut Speed
(m/min)
Net Weight (kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
Power (HP)
TG-25ZII 25 6 - 0.56 150 18,000 0.50 1⁄4 3⁄8 0.4
TG-38Z 25 6 - 0.70 178 23,000 0.45 1⁄4 3⁄8 0.4
TG-38ZL 25 6 - 0.63 163 23,000 0.50 1⁄4 3⁄8 -
TSG-3C 38 6 - 1.60 340 12,700 0.80 1⁄4 3⁄8 0.7
TSG-3CL 38 6 - 1.67 402 12,700 0.50 3⁄8 3⁄8 0.7
TSG-3F/3L 75 x 13 x 9.5 - 3,000 1.6 / 1.78 305 / 367 12,700 0.80 / 0.50 1⁄4 / 3⁄8 3⁄8 0.7
TSG-5L/5S 125 x 19 x 12.7 - 3,000 3.03 / 3.0 457 / 400 7,600 0.60 / 1.10 3⁄8 1⁄2 1.4
TSG-6L/6S 150 x 25 x 15.9 - 3,000 4.2 430 6,000 / 6,300 1.20 3⁄8 1⁄2 2.1
Specifications: Air Pressure 6kg/cm2
TSG-3F - 3” Straight GrinderTSG-3L - Lever Type
TG-25ZII - 6mm Collet Die Grinder
Straight grinders are Industrial Heavy Duty for general Grinding, Sanding and Wire Brushing Applications.
TSG-3C - 6mm Collet Die GrinderTSG-3CL - Lever Type
TG-38Z - 6mm Collet Die Grinder TG-38ZL - Lever Type
TSG-5S - 5” Straight Grinder/Wire BrushingTSG-5L - Lever Type
TSG-6S - 6” Straight Grinder/Wire BrushingTSG-6L - Lever Type
http://www.toku-net.co.jp/enMade in Japan
7
120mm
33mm
123mm
33mm
74mm
Motor cap Ø: 35mm
*Lever Type (L) Grinders are available upon request.
For more options on the Carbide Burrs, please refer to page 43 on Carbide Burrs
For more options on the wire brushes, please refer to Page 45 and 46 on Industrial Wire Brushes.
Recommended
SE-140 End Brush Ø 16mm
(Made in Japan)
TAG ANGLE GRINDER Heavy Industrial Duty
Specifications: Air Pressure 6kg/cm2
TAG-40FR - 4” Angle Grinder Roll Throttle (Female Thread)TAG-40MR - 4” Angle Grinder Roll Throttle (Male Thread)
TOKU Air Angle Grinders are designed with high power motor and speed control governor to deliver that continuous high cutting torque for maximum metal removal. Quality parts are used to ensure long durability under very heavy usage and minimum vibration to reduce operator’s fatigue. Diffuse exhaust silencer lower operator’s stress and prevent dusty particles blowing into other operator.
Choice of TAG40 - __ __ __
TAG-40SA - 4” Angle Grinder Roll Throttle TAG-40SML - Safety Lever Throttle (M10 Male Thread)TAG-40SAL - Safety Lever Throttle (Female Thread)
TAG-40FRH - Side Handle & Roll ThrottleTAG-40-FLH - Side Handle & Lever Throttle
http://www.toku-net.co.jp/enMade in Japan
8
FR - Female Type MR - Male Type
TAG-400 - 4” Angle Grinder Safety Roll ThrottleTAG-400QJL - 4” Angle Grinder Safety Lever Throttle
Legend:F - 5/8” Spindle Bore M - M10 male ThreadR- Roll ThrottleL - Lever Throttle
}}
H - Side Handle
TAG-20NR - 2” Angle Grinder Safety Roll Throttle
ModelWheel Size (mm)
Bore Size (mm)
Throttle Net Weight (kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
Power (HP)
TAG-20NR 58 9.5 Roll 0.55 162 12,500 0.5 1⁄4 3⁄8 0.4
TAG-40SA 100 16 Roll 1.4 204 12,000 0.6 1⁄4 1⁄2 0.7
TAG-40SAL 100 16 Safety Lever 1.4 204 12,000 0.6 1⁄4 1⁄2 0.7
TAG-40SML 100 M10 Safety Lever 1.4 210 12,000 0.6 1⁄4 1⁄2 0.7
TAG-40MR 100 M10 Roll 1.4 195 12,000 1.0 1⁄4 3⁄8 0.9
TAG-40FR 100 16 Roll 1.4 195 12,000 1.0 1⁄4 3⁄8 0.9
TAG-40FRH 100 16 Roll 1.8 217.5 12,000 1.0 1⁄4 3⁄8 0.9
TAG-40FLH 100 16 Safety Lever 1.6 213.5 12,000 1.0 1⁄4 3⁄8 0.9
TAG-400 100 16 Roll 1.7 220 12,000 0.5 3⁄8 1⁄2 0.7
TAG-400QJL 100 16 Safety Lever 1.8 266 12,000 0.5 3⁄8 1⁄2 0.7
TAG 7” & 9” ANGLE GRINDER Heavy Industrial Duty
TAG-700 - 7” Angle Grinder Roll Throttle
TAG-700QJL - 7” Angle Grinder Safety Lever Throttle
TAG-900 - 9” Angle Grinder Standard Roll ThrottleTAG-900QJL - 9” Angle Grinder Safety Lever Throttle
ModelWheel Size (mm)
Bore Size (mm)
Throttle Net Weight (kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
Power (HP)
TAG-700 180 22 Roll 3.1 274 7,500 0.8 3⁄8 1⁄2 1.3
TAG-700QJL 180 22 Safety Lever 3.1 304 8,400 0.8 3⁄8 1⁄2 1.3
TAG-900QJL 230 22 Safety Lever 3.4 304 6,500 0.8 3⁄8 1⁄2 1.3
OPTIONS
http://www.toku-net.co.jp/enMade in Japan
9
Specifications: Air Pressure 6kg/cm2
Cup Wire Brush*please refer to page 43 on industrial wire brushes
Grinding Disc
Diamond Cutting Wheel(Optional: Wheel Adaptor)
Ideal for operations such as cutting, grinding, deburring and wire brushing
SANDER Circular & Orbital Action
MS-4125B High Speed Sander
ES-680N5ES-680N6Standard Type
ES-680G5ES-680G6Dust Control - Self Vacuum Type
ES-730Orbital Sander
Model Paper/Disc Plate Size (in)
Paper/Disc Plate Size (mm)
Net Weight (kg)
Overall Length (mm)
Free Speed (rpm)
Avg. Air Cons (m3/min)
Air Inlet (pt)
Hose Size (in)
MS-4125B 5 75-115 1.0 115 14,000 0.38 1⁄4 3⁄8ES-680N5 5 125 0.68 140 12,000 0.40 1⁄4 3⁄8ES-680G5 5 125 0.77 210 12,000 0.40 1⁄4 3⁄8ES-680N6 6 150 0.73 140 12,000 0.40 1⁄4 3⁄8ES-680G6 6 150 0.82 225 12,000 0.40 1⁄4 3⁄8ES-730 7 x 31⁄2 90 X 180 0.95 220 10,000 0.40 1⁄4 3⁄8
10
Specifications: Air Pressure 6kg/cm2
Sanding Disc (For ES-680)• Available in 5” or 6”• 5 holes or 6 holes• Velcro or stick-on• Grit P16-P400
http://www.toku-net.co.jp/enMade in Japan
11
http://www.toku-net.co.jp/enMade in Japan
BABY HAMMER
MH-5111 - 1.6kg BRH-3 - 1.4kg
• Compact, light, handy and durable• Spool valve for fine control of
impacting speed• Built-in air regulator controls impact
power output
SCALING HAMMER / NEEDLE SCALER / FLUX CHIPPER
TS-2- Scaling Hammer TJN-200 - Needle Scaler
TFC-200 - Flux Chipper TFC-200F - Flux Chipper
Model Piston Dia x Stroke (mm)
Piston Dia x Stroke (in)
Stroke/Blow Per Min (bpm)
Net Weight (kg)
Overall Length (mm)
Avg. Air Cons (m3/min)
Air Inlet (pt)
Hose Size (in)
MH-5111 19 x 66 3⁄4 x 2 5⁄8 3,500 1.6 200 0.2 1⁄4 1⁄4BRH-3 10 x 76 3⁄8 x 3 1,800 1.4 200 0.32 1⁄4 1⁄4TS-2 30 x 30 13⁄16 x 13⁄16 8,000 2.2 500 0.3 3⁄8 1⁄2TJN-200 20 x 15 3⁄4 x 9⁄16 12,000 1.12 225 0.25 1⁄4 1⁄4TFC-200 20 x 12 3⁄4 x 7⁄16 12,000 0.89 182 0.25 1⁄4 1⁄4TFC-200F 20 x 12 3⁄4 x 7⁄16 12,000 1.06 187 0.25 1⁄4 1⁄4
Specifications: Air Pressure 6kg/cm2
• Designed for long life• Easy maintenance
• Handy and effective• No. of needles (3mm x 125mm): 12 pc
Accessories:o C15 – Chisel end (Width 10mm)o C15L – Chisel end (250mm)o M15 – Point endo B15 – Blank (flat end) Chisel
Accessories:o C20 – Width 19mm (185mm)o C20L – Width 19mm (250mm)
Accessories optional for MH-5111 and BRH-3Model Description Length (mm)
M5N Moil Point 200
C5N Chisel Point 200
Shank Size 10mm diameter
Applications: Effective in removing old paint & rust in difficult corner
Spare Piston P/No. 110102
Automotive ChiselsProduct Code
Description Blade width x Length
StyleShank size ø10mm
5202/5203 Fork 21/32 152
5204 Bushing Remover ø35 x 152
5207 Rivet & Body Cutter 19 x 152
5208 Blank ø13 x 178
5209 Spot Weld Breaker 146
5210 Sheet Metal(B) 143
5211 Bushing Tool 127
5214 Smoothing Hammer ø30 x 102
5216 Paint Scraper* 60 x 178
5217 Moil Point* 178
* Shank size ø12mm
• Heavy duty air hammer• Lightweight and durable• Ideal for general chiselling and cutting
jobs
12
AA SERIES & THA SERIES
SAND RAMMER & TAMPER
TOKU Chipping Hammers are proven reliable and durable, meeting all demand at any construction worksites.
• Easy to handle – Good weight balance• Least vibration at handle to reduce fatigue• Precision spool valve design system to ensure
maximum power against light body weight
AA-0B - 2.0kg AA-1.3B - 4.5kg AA-3B - 5.8kg THA-4S RV - 7.0kg
TOKU Tampers are ideal for compacting backfill for trenches. They are also commonly used in sand casting foundry.
Model Piston Diameter (mm)
Piston Stroke (mm)
Blow Per Min (bpm)
Net Weight (kg)
Overall Length (mm)
Avg. Air Cons Air Inlet Hose Sizem3/min cfm mm pt mm in
AA-0B 20.00 50 3,600 2.0 254 0.35 12.4 9.5 3⁄8 12.7 1⁄2AA-1.3B 24.00 58 2,800 4.5 320 0.45 15.9 9.5 3⁄8 12.7 1⁄2AA-3B 28.00 79 2,400 5.8 330 0.45 15.9 9.5 3⁄8 12.7 1⁄2THA-4S RV 28.54 102 1,800 7.0 480 0.95 33.5 9.5 3⁄8 12.7 1⁄2
Specifications: Air Pressure 6kg/cm2
Model Piston Diameter (mm)
Piston Stroke (mm)
Blow Per Min (bpm)
Net Weight (kg)
Overall Length (mm)
Avg. Air Cons Air Inlet Hose Size
m3/min cfm mm pt mm inTB-00G 18.0 50 1,600 1.7 280 0.25 8.0 9.5 3⁄8 12.7 1⁄2TB-0G 22.0 65 1,000 2.7 395 0.30 9.6 9.5 3⁄8 12.7 1⁄2TB-1N 25.4 100 800 5.4 510 0.70 22.4 9.5 3⁄8 12.7 1⁄2TF-1N 25.4 100 800 6.8 1,070 0.70 22.4 12.7 1⁄2 12.7 1⁄2TF-2N 32.0 125 700 9.0 1,105 0.85 27.2 12.7 1⁄2 12.7 1⁄2T-6 38.0 140 750 18.0 1,240 1.10 35.2 12.7 1⁄2 12.7 1⁄2
Specifications: Air Pressure 6kg/cm2
TF-1NTF-2N
T-6
TB-1NTB-00GTB-0G
Optional Accessories for AA-0BModel Description Length
(mm)Shank Size 12 x 53mm
M8N / M8L Moil Point 220 / 300
C8N Chisel 220
C8NL Long Chisel 300
Optional Accessories for AA-1.3B, AA-3B & THA-4S RVModel Description Length
(mm) Shank Size 15 x 60mm
M3N Moil Point 300
M3NL Long Moil Point 600
C3N Chisel 300
C3NL Long Chisel 586
D3 Asphalt Cutter 290
Claw coupling
Quick coupling Supply Hose
Supply Hose
Air HoseHoseStem
1mLead Hose
Note: To prevent hose stem breakage, suspend air hose to reduce stress to it
http://www.toku-net.co.jp/enMade in Japan
13
TB-1N
http://www.toku-net.co.jp/enMade in Japan
Model Description Length (mm)
Shank Size 7⁄8"Hex x 31⁄4"
M9 Moil Point 480
M9L Long Moil Point 710
M9LL Long Moil Point 1100
C9 Chisel 475
S9 Spade 4" 475
DEMOLITION TOOL
TCD-TRENCHER & CLAY DIGGER
TCB-CONCRETE BREAKER
Optional accessories for TCA-7 & G-9SModel Description Length (mm) Shank Size 26ø x 80mm
M7 Moil Point 400
M7N Moil Point 450
M7L Long Moil Point 600
M7LL Long Moil Point 1200
C7 Chisel 400
D7 Asphalt Cutter 450G-9S - 9.0kg TCA-7 - 7.2kg
Optional Accessories for TCD-20
TCD-20 - 10kg TCD-30 - 13.6kg (Optional Accessories Pg. 14)
Optional Accessories for TCB-200 & TCB-300Model Tools Type
M23 TCB-200
M33 TCB-300
C23 TCB-200
C33 TCB-300TCB-200 - 21kg TCB-300 - 30kg
ModelPiston
Diameter (mm)
Piston Stroke (mm)
Blow Per Min
(bpm)
Net Weight
(kg)
Overall Length (mm)
Avg. Air Cons. Air Inlet (pt)
Hose Size (mm) Shank Size
(m3/min) (cfm)G-9S 36.00 97 1,800 9.0 470 1.20 42.0 1 19.0 R26 x 80mmTCA-7 35.00 120 1,250 7.2 465 1.00 35.3 3⁄4 19.0 R26 x 80mmTCD-20 42.85 60 2,000 10.0 520 1.10 38.8 1⁄2 12.7 7/8" Hex x 3 1⁄4"TCD-30 44.45 85 1,550 13.6 559 1.40 49.4 1⁄2 12.7 1"Hex x 4 1⁄4"TCB-200 40.00 165 1,100 21.0 556 1.40 49.4 1 19.0 R30 x 87mmTCB-300 45.00 180 950 30.0 610 1.70 60.0 1 19.0 R35 x 87mm
Specifications: Air Pressure 6kg/cm2
• Simple Structure• Compact and light weight• Less maintenance• Powerful and durable
• Light-weight and high power• Automatic push throttle valve• Few parts for easy maintenance• Durable forged body• With chisel bush for long life
• Latch retainer for quick chisel change
• Optional Muffler available on request
Moil Point
Chisel Point
http://www.toku-net.co.jp/enMade in Japan
14
TPB SERIES - Concrete Breaker
TPB-30 - 15.0kg TPB-40 - 18.0kg TPB-90 - 42.0kgTPB-73 - 31.0kgTPB-60 - 30.0kg
• Forged steel body for maximum durability• 4-Bolt head design - rugged handling• Latch Retainer - quick chisel changing
Optional Accessories for TCD-30, TPB-30, TPB-40 (for more accessories please see Pg. 60)
Model Description OA Length (mm)
Shank Size 1"Hex x 41⁄4"
M4 Moil Point 580
M4L Long Moil Point
1330
C4S Chisel 500
Muffler - Optional for all breakers
Optional Accessories for TPB-60, TPB-73, TPB-90 (for more accessories please see Pg. 60)
Model Description OA Length (mm)
Shank Size 11⁄4"Hex x 61⁄4"
M1S Moil Point 550M1 Moil Point 620M1L Moil Point 760C1 Chisel 610
D1 Digger 3" 570
Model Description OA Length (mm)
Shank Size 11⁄4"Hex x 61⁄4"
DW1 Digger 5" 545
A1 Asphalt Cutter 540
ModelPiston
Diameter (mm)
Piston Stroke (mm)
Blow Per Min (bpm)
Net Weight
(kg)
Overall Length (mm)
Avg. Air Cons. Air Inlet (pt)
Hose Size (mm) Shank Size
(m3/min) (cfm)
TPB-30 44.45 85 1,550 15 564 1.4 49.4 1⁄2 12.7 1"Hex x 41⁄4"TPB-40 44.00 146 1,100 18 660 1.6 56.5 3⁄4 19.0 1"Hex x 41⁄4"TPB-60 57.15 100 1,400 30 645 2.0 70.6 3⁄4 19.0 11⁄4"Hex x 6"TPB-73 57.15 144 1,200 31 690 1.8 63.6 3⁄4 19.0 11⁄4"Hex x 6"TPB-90 66.67 152 1,250 42 723 2.2 77.7 3⁄4 19.0 11⁄4"Hex x 6"
Model Description OA Length (mm)
Shank Size 1"Hex x 41⁄4"
D4 Digger 3" 500
DW4 Digger 5" 490
A4 Asphalt Cutter 505
Specifications: Air Pressure 6kg/cm2
http://www.toku-net.co.jp/enMade in Japan
15
ROCK DRILL- Hand Held (5.8kg)
ROCK DRILL - Hand Held (14kg - 27kg)
TH-5S - 5.8kg
Mini Concrete and Rock Drill
Taper Rod T-15 (OAL)
400mm600mm900mm
Carr Bit T-15 (Dia)
20mm22mm
TJ-15LBS - 14.0kg TJ-20LBS - 18.5kg TS-55 - 27.0kgSpecifications: Air Pressure 6kg/cm2
ModelPiston
Diameter (mm)
Piston Stroke (mm)
Blow Per Min (bpm)
Rotary Speed (rpm)
Net Weight (kg)
Overall Length (mm)
Avg. Air Cons.
(m3/min)
Hose Size (mm)
TH-5S 38.0 35 3,400 420 5.8 425 0.85 12.7TJ-15LBS 54.0 45 2,450 250 14.0 507 1.60 19.0TJ-20LBS 68.0 49 2,400 200 18.5 610 2.50 19.0TS-55 66.6 65 1,800 200 27.0 568 2.60 19.0
Taper Rod T-22 (OAL)600mm900mm
1,200mm1,500mm2,400mm3,000mm4,000mm
Insert Bit (TH-5S) Taper Rod Drill Bit
Other sizes available on request
Taper RodDrill Bit
Optional Muffler
TJ-15 TJ-20
Button Bit: Higher drilling speed suitable for all kinds of rock or sand formation. Re-sharpening of bit is not necessary
Carr Bit: Suitable for rock formation without cracks
Insert Bit - Diameter x Length
13mm x 250mm13mm x 400mm16mm x 400mm16mm x 600mm19mm x 400mm19mm x 600mm22mm x 280mm22mm x 400mm22mm x 600mm
Taper Rod T-19 (OAL)
400mm600mm900mm
1,200mm
Carr Bit T-19 (Dia)
24mm26mm28mm30mm32mm34mm36mm38mm
Button Bit T-22 (Dia)
28mm
30mm32mm34mm36mm38mm40mm42mm45mm
Button Bit T-22 (Dia)48mm50mm55mm
Carr Bit T-22 (Dia)36mm44mm46mm
T-22 Taper Rod and Drill Bit
http://www.toku-net.co.jp/enMade in Japan
16
Water Swivel
Dry Shank
Wet Shank
Spiral Rod Spiral RodRodConnector
Auger BitStd Diameter:
42mm48mm65mm
Spiral RodStd Length:
0.5m1.2m
TAA-400
EARTH AUGER DRILL & DRILL ACCESSORIES
TAA-400 - Drilling Accessories
Female ThreadFT-3 : 3⁄8”FT-4 : 1⁄2“FT-6 : 3⁄4“
Male ThreadMT-3 : 3⁄8”MT-4 : 1⁄2“MT-6 : 3⁄4“
Air Hose End HE-3 : 3⁄8”HE-4 : 1⁄2“HE-6 : 3⁄4“
Rubber Seal R-6
• Most suitable for drilling holes for anchoring in tunnel and hill slope. • Optional - Air Leg support and water swivel attachment
Model Power (HP)
Speed:no load (rpm)
Speed: loaded (rpm)
Net Weight (kg) OA Length (mm) Air Cons.
(m3/min) Air Inlet (in) Air Hose (mm)
TAA-400 4 1,200 600-950 10.2 275 3.4 3⁄4 19
Carbide Auger Bit
TAA-400
WHIP HOSES
WIRE ARRESTOR / WHIP CHECK
Available in 1⁄4”, 3⁄8”, 1⁄2”, 3⁄4” in various connectionsUNIVERSAL AIR LINE CLAW COUPLING (Malleable Cast Iron)
Wire Arrestor / Whip Check Code: 9001SC ( 3 mm x 520 mm )The whip check is a safety device to prevent risk of hose whipping in the event of two hoses become uncoupled while under pressure
A
B
C
D
E
http://www.toku-net.co.jp/enMade in Japan
17
AIR WINCH - TAW Series Capacity - 300 kg to 2,000 kg
ADVANTAGES• Compact and light weight: Easy to handle• Two brakes (auto and manual): For operational safety• Spool valve allows speed control• Free drum disengaging lever: Operational flexibility• Hardy, reliable and durable: Reduce cost.
Specifications: Air Pressure 6kg/cm2
AIR MUCKING WINCH Capacity - 150kg & 300kg
ADVANTAGES• Built-in automatic brake: Operational safety• Totally oil enclosed gear selection: low maintenance• Light weight and compact size: Easy to handle and carry• High speed lifting: High productivity, lower cost.
STANDARD ACCESSORIES• Oil Lubricator• 40m wire rope and hook• Mill test cert. -125% loading
TMW-150
Optional:Filter Regulator Lubricator (F.R.L) & Remote Control (2 metre)
TAW winches are designed for lifting and pulling jobs, covering a wide range of application for the mining, construction, shipping and chemical industries.
Model Capacity(kg)
Speed(m/min)
Drum Capacity
(Wire Rope)
Air Data (cfm)
Winch with leg frame (kg)
Air Inlet / Hose size
(in)IMPA Code
TMW-150 150 45 5mm x 40m 66 56 1⁄2 59 06 04TMW-300 300 27 6mm x 40m 118 109 3⁄4 59 06 05
Model SWL (kg)
Wire Rope Rope Speed Air Cons (m3/min)
Net Weight
(kg)
Length (mm)
Width (mm)
Height (mm)
Drum Dia. (mm)
Air Inlet (pt)
Hose Size (mm)
Mounting Bolt -
Size x Qty(mm x m) (m/min)
TAW-300B 300 6 x 37 27 3.4 42.0 375 282 377 162 3⁄4 19 M10 x 4TAW-500 500 8 x 61 20 3.4 75.0 475 350 447 180 3⁄4 19 M12 x 4TAW-1000 1,000 10 x 91 11.5 3.9 90.0 581 350 448 200 3⁄4 19 M12 x 6TAW-1500A 1,500 12 x 60 8.5 4.1 90.0 581 350 448 200 3⁄4 19 M12 x 6TAW-2000 2,000 16 x 45 5.7 4.9 130.0 581 460 583 300 3⁄4 19 M12 x 6
18
http://www.toku-net.co.jp/enMade in Japan
AIR CHAIN HOIST CAPACITY - 250 kg to 25 ton
AIR BALANCER CAPACITY - 140 kg & 250 kg
AIR TROLLEY CAPACITY - 500 kg to 6.0 ton
Advantages in using TOKU Air Chain Hoist1. Steel alloy housing for durability and safety.2. Automatic built-in positive air disc brake. 3. Spring assisted rotor blades for variable speed operations:- i.e. smooth start and stop for lowering and lifting operations. 4. Built-in silencer for low noise -75 or 85 dBA at 1.0 m distance.5. Upper and lower limit switches6. Built-in load limiters for 500 kg to 6,000 kg7. Continuous duty air motor. 8. Both Pull Cord & Pilot Pendant controls9. Compact design (low head room) and light weight.10. ATEX certified II 2 GD IIAc T4 (135°C)
TCR-250C TCR-500PETCS-500PE
TNC-10TWALPETMH-25TP2E
TMM-140AE puts that 140 kg lifting power into your hand for greater flexibility and controlAdvantages:• One hand operation: freedom to adjust and align load• Flexible and easy to control: high productivity• Low noise level (80 dBA): user friendly• Auto brake: hold load securely when air supply is cut
off• Excellent INCHING operation: for
precise lowering and lifting jobs• Change from right-handed to left-
handed operation: suit operator’s choice
• Explosion proof motor: can be used near hazardous area.
Other optionsa. Trolley-Air operated or manual available to meet your needs. b. Chain Bag (optional) – available on request. c. Spark proof design (optional) – available on request. d. ATEX specification IIB & IIC - available on request.
Specifications: Air Pressure 6kg/cm2
Model TCR-250ME TMM-140AELifting Capacity (kg) 250 140
Standard Lift (m) 2.0 2.0Lifting Speed (m/min) 8.0 11.0
Net Weight (kg) 10.0 10.0Air Consumption (m3/min) 0.7 0.6
Specifications: Air Pressure 6kg/cm2
Model Capacity (kg)
Travel Speed
(m/min)
I-Beam Width (mm)
Min. Turn Radius
(m)
Air Supply
(m3/min)
Net Weight
(kg)
Air Inlet (in)
TMTNC-1 500 20 75-125 1.0 1.5 45 3⁄4TMTNC-1 1,000 20 75-125 1.0 1.5 45 3⁄4TMTNC-3 2,000 18 100-150 1.5 1.5 63 3⁄4TMTNC-3 3,000 18 100-150 1.5 1.5 63 3⁄4TMTNC-6 6,000 16 125-175 2.0 1.5 95 3⁄4
TOKU air chain hoist (TCR) is mounted onto the air trolley (TMTNC) via a bracket link, to form the combinedmodel: TMTCR-They are designed with adjustments for different I-Beam sizes. All are equipped with automatic brakes for added safety. Air Trolley of bigger capacity i.e. above 6 tons capacity are available on request.
Hook up package and push “UP” Button
Operator feels that he has the power to lift package effortlessly
Maximum flexibility and control in positioning the package
1
2
3
TMTCR-6000P2 (SWL - 6,000kg)
19
http://www.toku-net.co.jp/enMade in Japan
AIR CHAIN HOISTTOKU air chain hoists are widely used both onshore and offshore, throughout the world; typically in marine, ship building and repair yards, chemical and petrochemical plants, paint and paper making industries. You can always rely on TOKU hoist for its performance and safety that meets international quality standards.
Model ControlSWL Chain
Fall
Lifting Speed up (m/min)
Lifting Speed down (m/min)
Avg. Air Cons. Net Weight 3m HOL
(kg)
Hook to Hook(mm)
Hose Size
kg lb m3/min cfm mm in
TCR-250DPE Pendant 250 550 1 8.1 16.5 0.7 24.5 8.6 305 9.5 3⁄8TCR-250C Cord 250 550 1 9.0 17.4 0.8 28.0 7.0 305 9.5 3⁄8TCR-500C Cord 500 1,100 1 10.5 17.9 1.5 52.5 30.1 462 12.7 1⁄2TCR-500PE Pendant 500 1,100 1 10.5 17.9 1.5 52.5 31.1 462 12.7 1⁄2TCR-1000C2 Cord 1,000 2,200 2 5.3 9.0 1.5 52.5 34.2 519 12.7 1⁄2TCR-1000P2E Pendant 1,000 2,200 2 5.3 9.0 1.5 52.5 35.2 519 12.7 1⁄2TCR-1000C Cord 1,000 2,200 1 6.0 10.3 1.5 52.5 32.9 466 12.7 1⁄2TCR-1000PE Pendant 1,000 2,200 1 6.0 10.3 1.5 52.5 33.9 466 12.7 1⁄2TCR-2000C2 Cord 2,000 4,400 2 3.0 5.2 1.5 52.5 38.7 580 12.7 1⁄2TCR-2000P2E Pendant 2,000 4,400 2 3.0 5.2 1.5 52.5 39.7 580 12.7 1⁄2TMH-3000C Cord 3,000 6,600 1 5.4 10.5 3.9 136.5 97.4 537 19.0 3⁄4TMH-3000PE Pendant 3,000 6,600 1 5.4 10.5 3.9 136.5 98.4 537 19.0 3⁄4TMH-6000C2 Cord 6,000 13,200 2 2.7 5.2 3.9 136.5 115.4 742 19.0 3⁄4TMH-6000P2E Pendant 6,000 13,200 2 2.7 5.2 3.9 136.5 119.7 742 19.0 3⁄4TNC-10TWALC Cord 10,000 22,000 2 1.5 2.3 5.0 175.0 215.0 890 25.4 3⁄4TNC-10TWALPE Pendant 10,000 22,000 2 1.5 2.3 5.0 175.0 216.0 890 25.4 3⁄4TMH-25TC2 Cord 25,000 55,000 2 1.4 3.0 8.7 302.8 507.6 1290 38.1 11⁄2TMH-25TP2E Pendant 25,000 55,000 2 1.4 3.0 8.7 302.8 509.6 1290 38.1 11⁄2
HIGH SPEED TYPEModel Control
SWL Chain Fall
Lifting Speed up (m/min)
Lifting Speed down (m/min)
Avg. Air Cons. Net Weight 3m HOL
(kg)
Hook to Hook(mm)
Hose Size
kg lb m3/min cfm mm in
TCS-250PE Pendant 250 550 1 34.0 63.0 1.7 59.5 21.0 414 12.7 1⁄2TCS-250C Cord 250 550 1 34.0 63.0 1.7 59.5 18.0 414 12.7 1⁄2TCS-500PE Pendant 490 1,100 1 17.0 34.0 1.7 59.5 21.0 414 12.7 1⁄2TCS-500C Cord 490 1,100 1 17.0 34.0 1.7 59.5 18.0 414 12.7 1⁄2TCS-1000P2E Pendant 990 2,200 2 8.5 17.0 1.7 59.5 27.0 456 12.7 1⁄2TCS-1000C2 Cord 990 2,200 2 8.5 17.0 1.7 59.5 24.0 456 12.7 1⁄2
Note: Recommended operating air pressure 5 – 7 kg/cm2
Standard lifting height is 3.0m (additional lifting height by request is optional) except for TMM-140A & TCR-250M are 2.0mChain container available on request (optional)Pendant Control with Emergency Button (PE) available on request. For more detailed information, please contact your local distributor
TYPE OF CONTROL
You may already know…It is important to install an air treatment system such as FRL-filter, regulator, and lubricator – of suitable size and capacity. Good quality air supply means trouble-free operation of your air tools and hoists. Please see page 61 for details.
Periodically check your hoists for excessive wear and tear, especially the load chain. Report any unusual operational noise and have the problem corrected immediately by an authorised technician.
In some countries, hoists are inspected and load tested at specific intervals by Professional Engineers to ensure work safety requirement.
Specifications: Air Pressure 6kg/cm2
C Type - Cord Control P Type - Pendant Control
20
Made in Japan
AIR SAW & FILESaw Blade & File For AF-5A
Saw Blade & File For AF-10S
Part No. Description Remarks
SB-36S Saw Blade 36 tpi Steel Plate and Pipe - straight cut
AFF-50 File - Flat Steel Plate and Pipe, etc
AFR-50 File - Round Steel Plate and Pipe, etc
AFT-50 File - Triangle Steel Plate and Pipe, etc
Part No. Description Remarks
SB-14 Saw Blade 14 tpi Wood, Soft Plastic, Aluminium, etc
SB-24 Saw Blade 24 tpi Hard Plastic, etc
SB-32C Saw Blade 32 tpi Steel plate & Pipe - curve cut
SB-32S Saw Blade 32 tpi Steel plate & Pipe - straight cut
AFF-50 File - Flat Steel Plate and Pipe, etc
AFR-50 File - Round Steel Plate and Pipe, etc
AFT-50 File - Triangle Steel Plate and Pipe, etc
AF-5A - Air File
AF-10S - Air File / Air Saw
IMPA Code 590421ISSA Code 55.160.00
IMPA Code 590421ISSA Code 55.160.00
Model Stroke(mm) Stroke/min Overall
Length (mm)
Net Weight
(kg)
Avg. Air Cons
(m3/min)
Cutting Speed on 1mm Steel Plate Standard Accessories
AF-5A 5 3,500 158 0.38 0.20 500 mm/min 2 pcs - saw blade, 3 pcs - files
AF-10S 10 5,500 201 0.75 0.28 1,000 mm/min 3 pcs ea-saw blade & files
Specifications: Air Pressure 6kg/cm2
http://www.muromoto.co.jp/english/
Model Overall Length (mm)
Net Weight (kg)
Cutting Speed
Avg. Air Cons (m3/min) Max. Cutting Capacity (sheet)
PSH-10 225 1.23 1,900 /min 0.45 Metal - 1.5mm / Alu 2-mm / Resin - 2.5mm / Rubber - 3.0mm
Specifications: Air Pressure 6kg/cm2
AIR PLATE SHEARS (PSH TYPE)
PSH-10 - Best in cutting metal plate, rubber plate, resin plate, carpetwith E300S Standard Blade
E300S Standard Blade
E300 Long Blade (optional)For straight Cutting
E300H High Speed Steel Blade (optional)
21
Made in Japanhttp://nks-nakatani.co.jp
Model Collet Size (mm)Wheel Size (mm)
Free Speed (rpm)
Net Weight
(kg)
Overall Length (mm)
Avg. Air Cons
(m3/min)
Air Inlet (pt)
Hose Size (in)
Length (a)
Length (b)
NG-65L CR6mm or 1⁄4" optional
38 16,000 1.35 370 0.5 3⁄8 1⁄2 75 130
NG-65L CS 38 16,000 1.40 425 0.5 3⁄8 1⁄2 75 130
NG-65LL CR 38 16,000 1.60 515 0.5 3⁄8 1⁄2 75 255
NG-65L CS - Long Die Grinder (Lever Throttle)
NG-65L CR - Long Die Grinder
NG-65LL CR - Long Die Grinder
For more options, please refer to page 37 - ATA professional Air ToolsSpecifications: Air Pressure 6kg/cm2
EXTENDED BODY FOR SPECIAL GRINDING OPERATION
a b
a b
a b
ø30mm
ø30mm
ø30mm
OPTIONAL ACCESSORIES
For more options on the Carbide Burrs, please refer to page 43 on Carbide Burrs
For more options on the wire brushes, please refer to Page 45 & 46 on Industrial Wire Brushes.
FLAP WHEEL with SHANK Grit: P40 to P320For more options on abrasivesplease refer to page 44 on abrasives
WIRE BRUSH WITH SHANKFor more options on the wire brushes, please refer to Page 45 & 46 on Industrial Wire Brushes.
22
Made in Japan
HYBRID RATCHET WRENCH
SCALER-Needle & Chisel / Flux Chippers
KE-HR135
Hybrid Ratchet Wrench with its HYBRID MECHANISM allow the work to be torque without twisting the wrist and with two times more power.
Note: Good power to unscrew cap of 44 Gal. Drum
Model Square Drive (mm)
Bolt Capacity (mm)
Wrkg Torque Range (kg.m)
Free Speed (rpm)
Overall Length (mm)
Net Weight (kg)
KE-HR135 12.7 10 1 to 14 (10-140Nm) 180 340 1.7
• Straight or pistol grip handle to suit your application
• Option: Change to needle scaler from chisel scaler & vice versa
• AFC-20CN and AFC-30CN set is available. (comes with chisel and needle attachment)
AFC-30C - Chisel Scaler
AFC-20C - Chisel Scaler AFC-20N - Needle Scaler
AFC-30N - Needle Scaler
Model Piston dia. X Stroke (mm)
Number of Needle
Free Speed (bpm)
Net Weight (kg)
Overall Length (mm)
Avg. Air Cons (m3/min)
Air Inlet (pt)
Hose Size (in)
AFC-20N 20 x 20 3mm x 13pcs 4,000 2.5 395 0.19 1⁄4 3⁄8AFC-30N 25 x 22 3mm x 19pcs 4,000 2.8 410 0.20 1⁄4 3⁄8AFC-20C 20 x 20 C25 Chisel 4,000 1.8 180 0.19 1⁄4 3⁄8AFC-30C 25 x 22 C25 Chisel 4,000 1.7 210 0.20 1⁄4 3⁄8
Code DescriptionF-25 12mm width narrow chisel
S-25 35mm width straight flat chisel
C-25 35mm width bent chisel
D-25 60mm width straight chisel
Needles 3mm needles (100pcs/box)
Specifications: Air Pressure 6kg/cm2
Model Belt Size (mm)
Belt Speed (m/min)
Free Speed (rpm)
Overall Length (mm)
Net Weight (kg)
Avg. Air Cons (m3/min) Air Inlet (pt)
KE-370 10x330 1,100 16,000 290 0.8 0.1 1⁄4KE-380 20x520 2,000 17,000 360 1.4 0.3 1⁄4
Specifications: Air Pressure 6kg/cm2
KE-370 KE-380
BELT SANDER
48mm
AFC-30CN
Low Vibration
INDUSTRIAL AIR TOOLS
Made in Taiwan
23
Standard Accessories : • Patented Universal Swivel Joint • Carrying Box • Oil Bottle • 3mm Hex Wrench • Side Handle • Bi-Metal Saw Blades (300mm) (1 pc each - 14 TPI & 8/12 TPI)
Model Stroke/min
Stroke Length(mm)
Air Cons (m3/min)
Vibration (m/s2)
Noise Level (dBA) Weight (kg) Length
(mm) Air Inlet (in)
CCS-350D 1,200 45 0.13 5 85 2.80 470 1⁄4
ModelBlow
Per Min (BPM)
Air Cons (m3/min) Weight (kg) Length (mm) Needle
Type Air Inlet (in)
EP-100 13,000 0.02 0.22 140 Standard 1⁄4EP-100A 13,000 0.02 0.22 140 Professional 1⁄4
Model SQ Dr (in)
Collet / Chuck (mm)
Spindle Thread
Air Cons (m3/min)
Torque Range (Nm)
Free Speed (rpm)
Weight (kg)
Length (mm)
Air Inlet (in)
SM-40-7500 1⁄4” - - 0.11 34-95 12,000 1.0 170 1⁄4SM-55-5229 - 6 - 0.11 - 20,000 0.5 197 1⁄4SM-67-6661/58 - - 5⁄8” 0.09 - 4,500 1.9 307 1⁄4SM-6N-6661/58 - 5⁄8” 0.09 - 2,500 1.9 307 1⁄4SM-7H-7538 - 16 - 0.14 - 800 3.6 328 3⁄8
SM-40-7500 - 1/4” Mini Impact Wrench
SM-55-5229 - 115° Angle Grinder
SM-7H-7538 - 16mm Industrial Air Drill
SM-67-6661/58 - 7” Angle Sander SM-6N-6661/58 - 7” Angle Polisher
CCS-350D - Air Hacksaw
EP-100/100A - Engravepen76mm
24
Made in Korea
Pneumatic Leg Drillhttp://www.bigstonekorea.co.kr/
Model Piston ø (mm)
Piston Stroke (mm)
Blow Per Min (bpm)
Speed (rpm)
Weight (kg)
OAL (mm)
Shank Size (mm)
Air Cons (m3/min)
Hose Size (mm)
BRD-24LD 66.7 68 1,800 200 26 660 H22 X 106 2.7 19
Low VibrationLow MaintenanceHigh Productivity
Model Weight (kg) Length (mm) Extended Length (mm)
Feed Length (mm)
Feed Cylinder ø (mm)
Remarks
BL24 12 1,395 2,360 965 57 For BRD24LD
BRD-24LD Rock Drill with BL24 Support Leg
Pneumatic Jackleg Rock Drill
Support Leg
25
Hydraulic Drilling Mast
http://www.morath.euMade in Germany
• Photo shows AK12/80 coupled with TOKU TS-55 rock drill• Optional - can also coupled with Down-the-hole (DTH) hammer
Model AK12/80 AK14/80
Max drilling capacity Ø 115 115
Dimension L x H x B (mm) 1,817 x 225 x 290 2.057 x 225 x 290
Feed Length (mm) 1,200 1,400
Weight (kg) 40 43
Max feed force at 80 bar 3,800N 3,800N
Max retraction force at 180 bar 7,200N 7,200N
Max operating pressure (bar) 200 200
Oil requirement Approx 15l/min Approx 15l/min
Founded in 1967, Morath has evolved from a small family set-up to a globally recognised company in providing solutions on drilling - portable drilling, slope drilling, drilling unit attachments,etc.
AK 14/80 drilling mast complete with Rotary Head and Down-the-hole (DTH) Hammer with 76mm drill bit
26
Made in Japan
AIR WINCH – Capacity 500kg to 5,000kg
Founded in 1925, San-ei Seiki Seisakusho Co Ltd is a specialized manufacturer for pneumatic winches used mainly in heavy industries such as petrochemical, marine and offshore etc.
SANEI Air Winch are sturdy and compact in design, incorporating work safety features and ability to operate at difficult environment with minimum maintenance.
Model Capacity (kg)
Rope Speed (m/min)
Power (kw)
Wire Rope Capactiy(mm x m)
Weight w/o rope(kg)
Air Cons. (m3/min)
Mount Bolt - Size x Qty
W05-3 LAC-AB 500 19 1.73 8 x 90 64 2.0 M16 x 4W10-220 LAC-AB 1,000 37 7.15 10 x 350 288 5.4 M22 x 4W20-220 LAC-AB 2,000 19 7.15 12.5 x 230 297 5.4 M22 x 4W30-36 LAC-AB 3,000 19 12.0 16 x 320 527 9.0 M25 x 8W50-36 LAC-AB 5,000 11 12.0 22 x 230 873 9.0 M25 x 8
Specifications: Air Pressure 6kg/cm2
Please call our Customer Service for detailed catalogue
SAN-EI SEIKI SEISAKUSHO CO LTD
ADVANTAGES
• Easy Operation - Lever control
• Continuous Operation - 100% duty cycle
• Low maintenance
• Sturdy and compact in design
• Safe Mechanism - Manual or Automatic Band Brake
• No sparks generated
• Large drum diameter - Prolong wire rope life
• Optional - ABS Certification
BABY ELECTRIC WINCH Capacity - 150kg
ADVANTAGES
• Double Brake System: Electro-magnetic and anti-acceleration brakes
• Gears: Oil Submerged and totally enclosed for almost maintenance free operation
• Two buttons: Up and down operation plus E-Stop button
• Compact: lightweight and easy to carry around at work site
• Quick change replaceable motor: Reduce downtime
ModelSWL
Capacity (kg)
Dimensions:L x W x H(cm)
Voltage Motor (Watt)
Speed (m/min)
Net Weight
(kg)
Wire Rope
Hook Pendant Cord (m)
Supply Cord (m)
Max Rope Capacity (optional)
MA-650MB 150 49 x 29 x 29 220v 1ph 50/60 Hz
650 24 25 5mm x 40m
1pc 2.5 2 4mm x 60m
MA-650M 150 49 x 29 x 29 100v 1ph 50/60 Hz
650 24 25 5mm x 40m
1pc 2.5 2 4mm x 60m
MA-650MB - Small and Handy
TOYO KOKEN K. K.Made in Japan
ELECTRIC WINCH Capacity 200kg
http://www.liftket.deMade in Germany
27
Model LSF-200
Weight 60 kg
SWL Capacity 200 kg
Dimensions: L x W x H 741 x 640 x 334 mm
Voltage 400V/50Hz/3ph with 24V control
Power 0.55 kW
Drum/Rope Diameter 5mm x 80m
Lifting Speed 15m/min
Base to Hook 640 mm
ADVANTAGES
• Easy operation - Up/down with Emergency stop button
• Low voltage control - 24v
• Easy Installation - with angle bracket for ceiling fixing
• Compact: Light weight and easy to carry around
• Option: Wireless remote control
• IP 54
Optional: Hanger Mount
ELECTRIC CHAIN HOIST 0.25 TON to 25 TON
3 Simple Steps to select your STAR Liftket Hoists
to meet your requirements.
Step 1:
Step 2:
Step 3:
Determine your actual maximum load requirement and select from the first column. There is no need to give any extra load allowance as hoists capacity is the actual Safe Working Load (SWL) i.e. tested with the 25% overloading.
Confirm whether you need one or two speeds operation for lifting and lowering. Two speed hoists are recommended for handling of impact sensitive loads.
What type of suspension method is required, e.g. Top Hook, suspension, eye (bracket), electric trolley, etc…
HOOK SUSPENSION TROLLEY SUSPENSIONWe can design, build, supply, install, PE Testing and MOM Certification to meet your hoisting requirements. Call us for estimates without any obligation.
Types of Electric Hoist1. 2-speed: Lifting and Lowering2. 1-speed: Lifting and Lowering
Types of Hoist Suspension1. 2-Speed Electric Trolley2. 1-Speed Electric Trolley3. Push Trolley (Manual)4. Top Hook5. Eye Bracket
STAR Liftket Hoist
STAR Liftket is part of the continuous development of Hoffmann Fordertechnik GmbH to further improve the performance of Liftket Hoist.
STAR Liftket incorporates a modular motor system which is fan-cooled and very suitable for hot tropical climate, providing that longer working duty cycle.
http://www.liftket.deMade in Germany
28
415V 3ph 50Hz440V 3ph 60Hz (on request)Other voltage on request
HOOK SUSPENSION TROLLEY SUSPENSION
Hook to Hook (G1) Trolley Wheel to Hook (G2)
G2G1
*Refer to page 29 on actual G1/G2 dimensions
ELECTRIC CHAIN HOIST 415V 3ph 50Hz (440V 3ph 60Hz on request)STAR LIFTKET - One Speed & Two Speed Hoist
LIFTKET - Two Speed Hoist
STAR LIFTKET - 220V 1ph 50Hz (220V 1ph 60Hz on request)
SWL Capacity
(kg)
STAR Model
Lifting Speed
(m/min)
No. of LoadFalls
Lifting Motor (kW)
Duty Cycle ED %
Basic Hoist (kg)
Hook to Hook G1
(mm)
TrolleyWheel to Hook - G2
Trolley 2 SpeedTrolley Motors
(kW)
Trolley Weight
(kg)
250 021/51 8 / 2 1 0.32/0.08 40/25 17 432 4105 / 20 m/min 0.12 or
0.04 / 0.18 15 or 18500 021/51 4 / 1 2 0.32/0.08 40/25 19 485 454
500 030/52 8 1 0.7 40 18 432 4105 / 20 m/min 0.12 or
0.04 / 0.18 17 or 191,000 030/52 4 2 0.7 40 20 485 463
Trolley Type
Flange Width F
(mm)
N 50-106S1 110-200S2 210-300
N 66-135S1 137-215S2 220-300
500 071/53 10 / 2.5 1 0.9 / 0.2 60/25 42 492 4605 / 20 m/min 0.12 or
0.04 / 0.18 17 or 191,000 071/53 5 / 1.25 2 0.9 / 0.2 60/25 47 602 570
N 66-135S1 137-215S2 220-300
1,000 070/53 10 1 1.7 60 42 492 4605 / 20 m/min 0.12 or
0.04 / 0.18 17 or 192,000 070/53 5 2 1.7 60 47 602 570
N 66-135S1 137-215S2 220-300
1,000 071/55 6 / 1.5 1 1.1/0.2 60/25 42 492 4605 / 20 m/min
0.12 or 0.04 / 0.18
17 or 19
2,000 071/55 3 / 0.75 2 1.1/0.2 60/25 47 602 570
N 66-135S1 137-215S2 220-300
1,250 070/56 8 1 1.7 60 42 492 4805 / 20 m/min 0.04 / 0.18 29 or 30
2,500 070/56 4 2 1.7 60 47 602 590
N 66-135S1 137-215S2 220-300
1,600 091/56 10 / 2.5 1 3.0 / 0.75 60/25 88 616 5505 / 20 m/min 0.04 / 0.18 29 or 30
3,200 091/56 5 / 1.25 2 3.0 / 0.75 60/25 98 725 659
N 82-155S1 137-215S2 220-300
2,500 110/52 10 1 4.0 60 90 728 6764 / 16 m/min 0.04 / 0.18 63
5,000 110/52 5 2 4.0 60 107 858 806
N 90-155S1 160-226S2 240-310
3,200 111/54 8 / 2 1 4.4 / 1.1 25/25 118 728 6764 / 16 m/min 0.06 / 0.25 63
6,300 111/54 4 / 1 2 4.4 / 1.1 25/25 135 858 806
N 90-155S1 160-226S2 240-310
SWL Capacity
(kg)Model
Lifting Speed
(m/min)
No. of LoadFalls
Lifting Motor (kW)
Duty Cycle ED %
Basic Hoist (kg)
Hook to Hook G1
(mm)
Trolley Wheel to Hook - G2
(mm)
Trolley 2 SpeedTrolley Motors
(kW)
Trolley Weight
(kg)
6,300 B13 5.6 / 1.4 1 6.4/1.6 60/40 224 995 9034 / 16 m/min 0.12 / 0.55 137
12,500 B13 2.8 / 0.7 2 6.4/1.6 60/40 254 1089 997
Trolley Type
Flange Width F
(mm)
N 140-230
S1 220-310
SWL Capacity
(kg)
STAR Model
Lifting Speed
(m/min)
No. of LoadFalls
Lifting Motor (kW)
Duty Cycle ED %
Basic Hoist (kg)
Hook to Hook G1
(mm)
500 050/02 8 1 0.7 40 33 462
1,000 050/02 4 2 0.7 40 35 515
Curve RadiusTrolley Capacity Model Min. Curve radius
up to 1,000 kg Up to 070 1.0 m
up to 3,200 kg 091 1.5 m
up to 6,300 kg 110 / 111 2.0 mManual Push Trolley available on request
http://www.liftket.deMade in Germany
29
Remark : Model 13/00X, only for straight beam
POWER LIFTKET - Two Speed Hoist
SWL Capacity
(kg)
STAR Model
Lifting Speed
(m/min)
No. of LoadFalls
Lifting Motor (kW)
Duty Cycle ED %
Basic Hoist (kg)
Trolley Wheel to
Hook - G2 (mm)
Trolley 2 Speed
Trolley Motors
(kW)Trolley Weight (kg)
16000 235/50 3.2 / 0.8 2 12.5/3.1 25/10 668 1,700
4 / 16 m/min 0.12 / 0.55 27420,000 235/50 3.2 / 0.8 2 12.5/3.1 25/10 668 1,700
25,000 235/50 3.2 / 0.8 2 12.5/3.1 25/10 668 1,700
Trolley Type
Flange Width F
(mm)
N 140-230
S1 220-310
250 051/55 18 / 4.5 1 0.9 / 0.2 60/25 33 462 4365 / 20 m/min 0.12 or
0.04 / 0.18 15 or 18500 051/55 9 / 2.25 2 0.9 / 0.2 60/25 35 515 489
N 66-135S1 137-215S2 220-300
Trolley Turning Radius
Remark : Max lifting height for B13 6,300= 110 metre, B13 12,500 = 55 metre
NEEDLE SCALERTrelawny Surface Preparation Technology is a market leader in the design, manufacture and supply of a comprehensive range of critical surface preparation tools and equipment. Specially designed for efficient removal of paint, rust and coating from steel and concrete surfaces. An ISO-9001 accredited company established for over 60 years.
Reduce the risk of vibration-related injuries, always look for the “Vibro-Lo” Label.
• Extremely low vibration greatly reduces operator fatigue – increase productivity and eliminate sickness caused by long hour using a high vibrating tool. Try one and know the difference instantly.
• Call now for a FREE – No Obligation DemonstrationVL-303 - Vibro-Lo Needle Scaler• Noise Level: 109.5 dBA• Vibration Level Aeq: 2.3m/s2
• Very Low Vibration, greatly reduce worker’s hand fatigue.
Needle Scaler - In-Line Needle Scaler - Pistol Grip
Model ISSA Code
IMPA Code
Design Type
Piston Dia. X Stroke (mm) BPM Weight
(kg)Length (mm)
Air Cons. (m3/min)
Air Inlet (pt)
No. of needle
2mm 3mm 4mm
VL-303 55.091.40 59 05 10 Pistol Grip 34.4 x 20 3,000 3.5 370 0.13 1⁄4 - 28 19
1B-N 55.091.01 59 04 81 In-Line 18 x 30 3,800 1.7 343 0.08 1⁄4 29 12 -
2B-N 55.091.05 59 04 62 In-Line 23.5 x 35.6 3,000 2.6 375 0.17 1⁄4 51 19 -
2BPG-N 55.091.10 59 04 82 Pistol Grip 23.5 x 35.6 3,000 2.6 315 0.17 1⁄4 51 19 -
3BPG-N 55.091.20 59 04 83 Pistol Grip 28.6 x 39 2,200 3.8 342 0.25 1⁄4 65 28 19
4B-N 55.091.20 59 04 84 Pistol Grip 33 x 49.2 2,200 5.9 482 0.26 1⁄4 - 49 35
http://www.trelawnyspt.co.ukMade in England
30
Specifications: Air Pressure 6kg/cm2
Needles HDiameter x Length : -2 mm x 180 mm (100 pc / box)3 mm x 180 mm (100 pc / box)4 mm x 180 mm (50 pc / box)
Spark Proof Needle (Copper)3 mm x 180 mm (100 pc / box)BS – 2873 & ATEX – CE Standards
Code For Needle/ Chisel Scaler Part No.
59 05 98 VL203/VL223 720.2003
59 05 99 VL303 720.3003
FALL ARRESTER
Non-sparking and non-magnetic material suitable for use in potentially explosive atmospheres
Flat Tip: reduce marking on the surface (2mm needles used on welds give a shot peening effect reducing stress in the weld)
Chisel Tip: feature a sharpened chisel tip for aggressive removal of material while minimising indentation to the surface.
Pointed Tip: feature a sharpened conical point. These are the most aggressive needles for breaking hard coatings & scale.They leave heavy indentations in the surface where a keying of the surface is required
Spark Proof Needle (Copper)3 mm x 180 mm (100 pc / box)BS – 2873 & ATEX – CE Standards
Chisel Scaler - Pistol Grip
Chisel Scaler - In-Line
CHISEL SCALER
POLE SCABBLER
LPS-55 Pole Scabbler with tungsten carbide headWeight: 13.4 kgLength: 1,392 mmB.P.M: 1,100Air Consumption: 0.33m3/minDesigned specifically for effective roughening of hard concrete floor and confined space.
http://www.trelawnyspt.co.ukMade in England
31
TCT 5 point bush headPart No 441.5359
Model ISSA Code IMPA Code Design Type Piston Dia. X Stroke (mm) BPM Weight
(kg)Length (mm)
Air Cons. (m3/min) Air Inlet (pt)
1B-C 55.091.02 59 05 81 In-Line 18.0 x 30.0 3,800 1.6 313 0.08 1⁄4
2B-C 55.091.06 - In-Line 23.5 x 35.6 3,000 2.0 343 0.17 1⁄4
2BPG-C 55.091.11 59 05 82 Pistol Grip 23.5 x 35.6 3,000 2.1 260 0.17 1⁄4
3BPG-C 55.091.21 59 05 83 Pistol Grip 28.6 x 39.0 2,200 2.6 339 0.25 1⁄4
4B-C 55.091.21 59 05 84 Pistol Grip 33.0 x 49.2 2,200 4.0 440 0.26 1⁄4
VL-303C - - Pistol Grip 34.4 x 20.0 3,000 4.25 370 0.13 1⁄4
Specifications: Air Pressure 6kg/cm2
H
Chisel - 1⁄2” square shank
(Aluminum Bronze) T704.1110 - 50mm width Straight Wide Chisel - T704.1103 (64mm width)
Straight Flat Chisel - T704.1101 Bent Wide Chisel - T704.2105 (35mm width)
Spark Resistant Chisel
ATEX APPROVED LOW VIBRATION NEEDLE SCALERSVL EX series supplied in a heavy duty plastic case.
The case consists of :
• VL203/223/303 Low Vibration ATEX Needle Scaler• Spare set of Beryllium Copper Needles• TVS Vacuum Shroud• Fall Arrestor• Corner Cuff• Edge Cuff• Operator Guide
Model Part No. Type Needle Quantity
Weight (kg)
Blows per Min (BPM)
Air Cons. (m3/min)
Air Inlet Size (in)
Noise Level (dBa)
Vibration level Aeq (m/s2)
V223Ex 139.2423 In-Line 19 x 3mm 2.35 2,400 0.11 1/4 90.7 2.56
V203Ex 139.2403 Pistol Grip 19 x 3mm 2.70 2,400 0.11 1/4 90.7 2.75
V303Ex 139.2433 Pistol Grip 28 x 3mm 3.51 3,000 0.16 1/4 109.5 2.30
ATEXLow Vibration
Needle Scaler Kit
Noise Level: 92.5dBAVibration Level: 3.7m/s2
http://www.trelawnyspt.co.ukMade in England
32
SCALING HAMMER-Single & Triple Heads
SF-3 - Integral Steel Piston (153.5380) SF-3- Taper TCT Piston (153.5300)SH-3H - Integral TCT Piston (153.5200)
SF-1 - Integral Steel Piston (151.5180)SF-1 -Taper TCT Piston (151.5100)VL SF-1 - Low Vibration, Taper TCT Piston (196.5095)
SCALING HAMMER-Integral Piston Type
Taper Piston - SF-1, SF-3 & SF-11 (piston with removable head)
Integral Piston Standard Hard Steel Part No. 612.5305
Model Part No. ISSA Code IMPA Code B.P.M Weight (kg)
Length (mm)
Air Cons. (m3/min)
Air Inlet (pt)
Spare PistonUsed
SF-1 151.5180 55.093.01 59 03 82 3,800 2.5 485 0.13 1⁄4 612.5305, 5320,5325
SF-3 153.5380 55.093.03 59 03 83 3,000 x 3 3.7 485 0.31 1⁄4 612.5305, 5320,5325
SH-3H 153.5200 55.093.04 59 03 83 2,400 x 3 5.3 460 0.41 1⁄4 612.5320, 5305, 5325
Model Part No. ISSA Code
IMPA Code B.P.M Weight
(kg)Length (mm)
Air Cons.
(m3/min)
Air Inlet (pt)
Taper Piston
X-Form Head
Bush Head
Beryllium Copper
SF-1 151.5100 55.093.01 59 03 82 3,800 2.5 460 0.14 1⁄4 612.5301 426.5351 426.5352 606.5303
SF-3 153.5300 55.093.03 59 03 83 3,000 x 3 3.7 460 0.31 1⁄4 612.5301 426.5351 426.5352 606.5303
VL SF-1 196.5095 55.093.01 59 03 82 3,000 2.5 465 0.31 1⁄4 612.5301 426.5351 426.5352 606.5303
SPARE HEADS
Spark Resistant HeadBeryllium CopperPart No. 606.5303
Cruciform HeadTungsten Carbide Tipped
Part No. 426.5351
Bush headTungsten Carbide Tipped
Part No. 426.5352
Taper PistonPart No. 612.5301
Integral Piston (Cruciform Head)Tungsten Carbide TippedPart No. 612.5320
Integral Piston (Bush Head)Tungsten Carbide TippedPart No. 612.5325
H
SCALING HAMMER-Taper Piston Type
Model Part No. ISSA Code IMPA Code B.P.M Weight
(kg)Height (mm)
Air Cons. (m3/min)
Air Inlet (pt)
MHS-5 159.5050 - - 1,300 x 5 114.0 970 2.25 3⁄4
MHS-11 159.6000 - - 2,200 x 11 70.0 1,290 1.98 3⁄4
SF-11 159.5910 55.095.01 59 04 05 3,000 x 11 36.0 1,210 1.98 3⁄4
http://www.trelawnyspt.co.ukMade in England
33
MULTI HEADS SCALING MACHINE - For Construction
Features:• Built in dead man’s handle• Large Wheels for rough terrain• Vibration reduced to combat operator’s fatigue
MHS-11 - Multi Head ScalerFor Concrete and Hard Surfaces
SF-11 - Multi Head ScalerFor quick rust removal on steel surface
Features:• Effective in removal of road marking, ship deck paint and
rust
5 pcs bush hammer scabbler head
FAST CONCRETE REMOVAL
Features:• Eleven pieces of Carbide
Bush Heads for faster removal rate
• Heavy Design Head Block for effective roughening of concrete surface
MULTI HEADS SCALING MACHINE - For Marine
TCT 5 point bush headPart No 441.5359
Spark Proof HeadPart No. 606.5303
X-Form HeadPart No. 426.5351
Bush headPart No. 426.5352
Taper PistonPart No. 612.5301
Integral PistonTungsten Carbide Tipped
Part No. 612.0125
MHS-5 - Multi Head ScalerFor Concrete and Hard SurfacesWeight: 114 kg5 pistons x 1,300 BPM
MULTI-HEADS SCALING MACHINE
H
HEAVY DUTY SCALING HEAD6” Power Brush 6” Twisted Knot Brush Crimped Wire Cup Brush Twisted Knot Cup Brush
Part No: 340.160 ISSA: 55 084 03 IMPA: 59 12 93
Part No: 340.163 ISSA: 55 084 01IMPA: 59 12 91
Part No: 340.166 ISSA: 55 084 07 IMPA: 59 12 97
Part No: 340.167 ISSA: 55 084 05 IMPA: 59 12 95
Centre Bolt for 6” Power Brush Centre Bolt for6” Twisted Knot Brush
Centre Bolt for Crimped Cup Brush Centre Bolt for Twisted Cup Brush
Part No: 340.558 ISSA: 55 084 04 IMPA: 59 12 94
Part No: 340.559 ISSA: 55 084 02 IMPA: 59 12 92
Part No: 340.557 ISSA: 55 084 08 IMPA: 59 12 96
Part No: 340.557 ISSA: 55 084 06 IMPA: 59 12 96
FLEXIBLE SHAFT complete with Hand piece and Coupling
http://www.trelawnyspt.co.ukMade in England
34
TRIDENT NEPTUNE - Deck De-Scaler
Accessories
Model Power Type Voltage RPM Power (kw)
Weight (kg) ISSA Code IMPA
Code340.TN/S/110 Elect Motor 110V 1ph 50/60Hz 3,000 0.55 34 55.077.00 59 12 41
340.TN/S/220 Elect Motor 220V 1ph 50/60Hz 3,000 0.55 34 55.077.00 59 12 42
340.490/S Air Motor Air Pressure - 6kg/cm2 3,200 0.75 34 55.077.00 59 12 81
Part No: 340.285 ISSA: 55 077 01 IMPA: 59 12 99
The machines will rapidly remove scale, rust, paint and other unwanted deposits, leaving a good surface suitable for priming/painting or coating application.FEATURES• Greater portability : 25% lighter• Automatic thermal protection on
electric models - protects motor from overheating
• Skid design base - stops the machine rolling around on decks
All machines supplied with:• Flexible shaft 3 m x 16 mm (9ft x 5/8”)• Heavy duty leaf scaling head• 6 cutter scaling head• 150mm dia (6”) power brush• Spanner set• Hand guard TRIDENT NEPTUNE
Electric 110V 1ph 50/60HzElectric 220V 1ph 50/60Hz
6 CUTTER SCALING HEADSix Cutter Scaling Head Cutter Wheel Side Plate Cutter Pin Centre Bolt
Part No: 340.581 ISSA: 55 082 01 IMPA: 59 12 86
Part No: 340.332 ISSA: 55 082 04 IMPA: 59 12 89
Part No: 340.575/2 ISSA: 55 082 02 IMPA: 59 12 87
Part No: 340.583 ISSA: 55 082 05 IMPA: 59 12 90
Part No: 340.581/A ISSA: 55 082 03 IMPA: 59 12 88
HEAVY DUTY SCALING HEADHeavy Duty Scaling Head Chipping Leaf Side Plates (Set of 2) Cutter Pin Centre Bolt Spacing Washer (Set of 50)
Part No: 340.550 ISSA: 55 078 01 IMPA: 59 12 75
Part No: 340.347 ISSA: 55 078 06 IMPA: 59 12 79
Part No: 340.551/2 ISSA: 55 078 02 IMPA: 59 12 76
Part No: 340.553 ISSA: 55 078 05 IMPA: 59 12 80
Part No: 340.552 ISSA: 55 078 03 IMPA: 59 12 77
Part No: 340.584/50 ISSA: 55 078 04 IMPA: 59 12 78
TRIDENT NEPTUNEAir Motor Type: Air Pressure - 6kg/cm2
MULTI PLANER - TFP MACHINE - FLOOR SCALING MACHINE
REFILLS:Tungsten Carbide Tipped Cutter (T320.5500)• Inserted with tungsten carbide tips• Effective for concrete planing, removal of road
markings & floor coatings
Beam Cutter (T320.5120)• Hardened alloy steel cutter• Effective for removal of old paint, coatings and
deposits from concrete and steel floors
Star Cutter (T320.3658)• Heat treated steel cutters • Effective for removal paint coatings and laitance from new coatings.• Can be used for removal of built-up of grease, dirt, sticky coatings
and ice deposits
Model Power Type IMPA Code ISSA Code Weight (kg)
Speed (rpm)
TFP-200E 110V 1ph 60Hz 59 22 35 55.096.02 72 1,753
TFP-200E1 220V 1ph 50/60Hz 59 22 36 55.096.02 71 1,753
TFP-200E2 415V-440V 3ph 50/60Hz 59 22 37 55.096.02 68 1,753
TFP-200P Petrol Engine - 55.096.01 59 1,833
TFP-200D Diesel Engine - - 56 1,750
TFP-200A Air Motor (Air Cons.5m3/min) 59 22 31 - 63 1,810
TFP-200 Floor Planer• Working Width: 195 mm• Cut up to 3 mm concrete per run• Options: Electric Motor or Petrol Engines• Noise level: 90 dBA• Vibration level: 10.3 m/s2
• Side Clearance: 50mm• Depth control adjuster - Improves performance and cutter durability
Twisted Wire Brush (T320.9622)• Effective in removal of floor stains or coatings and rust on flat steel
surface
http://www.trelawnyspt.co.ukMade in England
35
Accessories
Crimped Wire Brush (T320.9612)• For general cleaning and removal of light surface rust
Model Power Type IMPA Code ISSA Code Weight (kg)
Speed (rpm)
TFP-250E2 5.5Hp / 4kw Electric Motor(415-440V 3ph 50/60Hz)
- - 127 1,750
TFP-200
TFP-250
OPTIONS:T320-1020ST Tungsten Carbide Drum AssemblyT320.1020SB Beam Cutter Drum AssemblyT320.1020SS Star Cutter Drum Assembly
OPTIONS:T320.9620 Twisted Wire Brush Drum Assembly T320.9610 Crimped Wire Brush Drum Assembly
PEENING PREPARATION TOOLS - Handheld Scarifiers
http://www.trelawnyspt.co.ukMade in England
36
The PPT range of hand scarifiers utilise the 3MTM brand of RotopeenTM ‘ C ’ flaps to offer a captive shot method of surface preparation. Used with the range of Trelawny TVS dust collectors, the PPT will remove hazardous materials such as lead based paints and contaminated particles rapidly and dust free.
ApplicationsA range of steel and concrete substrates can be cleaned and prepared to provide a keyed surface using these high production tools.
Ideal for the removal of:• Alkyds• Mastics• Epoxies• Adhesives• Lead based paints• Coatings corrosion
• Abatement projects
Accessories
Pneumatic model 194.C405 100mm cutting width with star
cutters
Star cutter
Aggressive removal of thick coatings
Part No. 312.S200
Beam cutter
Removal of hard coatings, less aggressive than starPart No. 312.R200
3MTM Heavy Duty RotopeenTM
‘C’ Type Flap
Removal of light paint and rust to a bare metal finish
Part No. 312.MRPC
Part No.Cutting Width Cutting Media
Power Weight (kg) RPM Air Cons.
(m3/min)Vibration level
Aeq (m/s2)50mm 100mm ‘C’ Flaps Star Cutters194.0405 √ √ Air 4.10 2,700 0.85 3.10
194.C405 √ √ Air 6.47 2,700 0.85 4.60
Pneumatic model 194.0405 100mm cutting width with “C’ Flaps
Air/Electric Vacuum SystemSeries K is ATEX approved for Gas Zone 1 & Dust Zone 21 under Category 2 of the ATEX Directive.
Electric options available : 220v/110v 1ph 50 Hz
HYDRAFLEX - WATER JET
http://www.trelawnyspt.co.ukMade in England
37
SpecificationsWater Pressure 85 psi
Air Pressure 100 psi
Air Consumption 2 m3/min
Air Hose 3/4”
Water Hose 2”
Total Weight 15 kg
Gun (weight / length) 5.6kg / 740mm
Tripod (weight / length) 9.4kg / 1400mm
Water Consumption 485 L/min or 110 gal/min
Hydraflex GunEffective Range: 30 metreSolid Stainless Steel Nozzle designed for durability that increases power of water jetting.
Standard kit includes:-1. Gun 342.HY012. Tripod 342.HY023. Water Hose Coupling 2” 342.HY044. Instantaneous Water Hose Adapter 342.HY05
ISSA Code: 55.085.01IMPA Code: 59 07 42
Applications:One-man operation to clean residue, loose paint, flaking rust and other substances from ships holds.
Features:• Specially designed as a means of washing ship’s cargo holds
between cargo & differing commodities.• Compressed air forces water into a powerful jet. • Produces a jet of up to 30 meters sufficient for most large bulk
carriers.• Simple to set-up and easy to operate.• Tripod base kit for operator stability.
LR-2LR-5
Model ISSA Code IMPA Code B.P.M Weight (kg) Length (mm) Air Cons. (m3/min) Air Inlet (pt)LR-2 55.094.01 59 04 51 2,200 4.8 740 0.13 1⁄4
LR-5 55.094.03 59 04 53 2,200 6.25 1,400 0.13 1⁄4
LLR-5 LITE - Light Weight 2,200 4.05 1,400 0.13 1⁄4
LRS-55 - - 1,100 13.4 1,392 0.7 male 1⁄2"
Trelawny Part No. Chisel Blade Width ISSA Code IMPA CodeT705.1106 50 mm 55.094.11 59 04 55
T705.1102 100 mm 55.094.13 59 04 56
T431.3504 102 mm 55.094.09 59 04 56
T431.3508 203 mm 55.094.10 59 04 57
T431.3512 305 mm 55.094.12 59 04 58
Optional Accessories
LONG REACH SCALER - Chisel and Needle Attachment
Optional: LR Long Reach Scaler can be installed with a needle attachment, i.e. 3 mm Needle x 28 pcs
ADH2020 mm - 3⁄4”
ADH2525 mm - 1”
ADH3838 mm - 1 1⁄2”
ADH5050 mm - 2”
ADH7575 mm - 3”
SPM-45RSPM-60R- Pencil Grinder ST-100 - Turbine Grinder
TURBINE GRINDER AND PENCIL GRINDER
Model RPM Power (HP)
Dimension Weight (kg)
dBA Air Cons (m3/min)
Exhaust Outlet
Inlet (in)
Collet size Hose Included (m)
SD-45R-CC 45,000 0.20 ø 26 x 140 0.24 64 0.23 Rear 1⁄4 3mm 2
SD-45R-CE 45,000 0.20 ø 26 x 160 0.24 64 0.23 Rear 1⁄4 1 ⁄8" 2
SPM-45R 45,000 0.20 ø 20 x 132 0.15 60 0.20 Rear 1⁄4 3mm 2
SPM-60R 60,000 0.15 ø 20 x 132 0.15 63 0.20 Rear 1⁄4 3mm 2
ST-100 100,000 0.06 ø 31 x 150 0.24 62 0.17 Front 1⁄4 3mm 2
http://www.atagroup.coMade in Ireland
38
RAM-20LR RPM-25R
Angle Head Die Grinder with Collet and ATA Disc Adaptors (both accessories included) for fine sanding and polishing job
ANGLE HEAD DIE GRINDER & SANDER
Model RPM Power (HP)
Dimension D x L x H (mm)
Weight (kg)
dBA Air Cons (m3/min)
Exhaust Outlet
Inlet (in)
Collet size (mm)
Hose Included (m)
RAM-20LR 20,000 0.40 ø 36 x 167 x 70 0.52 74 0.57 Rear 1⁄4 6 3
RPM-25R 25,000 0.15 ø 20 x 140 x 33 0.23 68 0.20 Rear SF 3 2
ATA Unique Replacement MotorATA - Abrasives & AccessoriesATA Discs
Qty Dia. (mm) Part No.2 75 AD75-60 GRIT2 75 AD75-120 GRIT1 75 AD75-180 GRIT1 50 AD50-60 GRIT1 50 AD50-80 GRIT
Scrulok DiscsQty Dia. (mm) Part No.
2 75 SLD75-36 GRIT2 75 SLD75-50 GRIT1 50 SLD50-50 GRIT1 50 SLD50-80 GRIT
Backing PadsQty Dia. (mm) Part No.1 50 ABDP50 Black1 75 ABDP75 Blue
SD-45R-CCSD-45R-CE (extended collet holder)
General Features• High power and proven durability• Ergonomic and low vibration design - Operator’s comfort and
reduced fatigue• Extended Narrow Spindle for better access• Wide Options on Speed, Throttle and Exhaust• Wide range of Collet Sizes Available
Instant ATA Unique Replacement MotorLoosen and dissemble grinder:Fig. 1 & 2, Remove old motor and replace with new motor as shown. Fig. 3 - Assemble, tighten and back to work. Fig. 4 - Completion
DIE GRINDER
*Collet size: 6mm Optional Collet sizes: 3mm, 1/8” and 8mm L= Lever Throttle R= Rear Exhaust
Push-Pull Throttle - S-25Front Exhaust and Roll Throttle
Lever Throttle - S-22L
DIE GRINDER - Restricted Access
Model RPM Power (HP)
Dimension (mm)
Weight (kg)
dBA Air Cons (m3/min)
Exhaust Outlet
Inlet (in)
Collet size (mm)
Hose Included (m)
SDM-26LRES 25,000 0.40 ø 36 x 232 0.45 72 0.57 Rear 1⁄4 3 3
SDHM-30LR-150 30,000 0.40 ø 36 x 288 0.82 73 0.57 Rear 1⁄4 6 3
DIE GRINDER - Extended Body
Model RPM Power (HP)
Dimension (mm)
Weight (kg)
dBA Air Cons (m3/min)
Exhaust Outlet
Inlet (in)
Collet size (mm)
Hose Included (m)
STX-10L 10,000 0.85 ø 43.0 x 316 1.4 65 0.85 Front 1⁄4 6 No
SMX-10LR 10,000 1.1 ø 42.0 x 345 1.3 74 0.62 Rear 1⁄4 6 No
SMX-16LR 16,000 1.1 ø 42.0 x 345 1.3 77 0.62 Rear 1⁄4 6 No
STX-10L
Suitable for heavy duty deburring, sanding and polishing, in the most demanding environment and shock loading jobs
39
SDM-26L
http://www.atagroup.coMade in Ireland
SDHM-30LR-150 - Heavy-duty deburring with extended Spindle Ø 21mm x Length 150mm
SDM-26LRES- Deburring with extended chuck body Ø 9.5mm x Length 80mm
SMX-10LR / SMX-16LR
SDM-26LR P-25A SM-25LRModel RPM Power
(HP)Dimension
(mm)Weight
(kg)dBA Air Cons
(m3/min)Exhaust Outlet
Inlet (in)
Collet size (mm)
Hose Included (m)
S-22L 22,000 0.85 ø 42 x 184 0.93 71 0.85 Front 1⁄4 6 No
SM-25LR 25,000 1.10 ø 40 x 213 1.00 74 0.62 Rear 1⁄4 6 Included
S-25 25,000 0.30 ø 34 x 163 0.36 67 0.21-0.49 Front 1⁄4 3 No
SDM-26L 25,000 0.40 ø 36 x 167 0.46 73 0.57 Front 1⁄4 6 No
SDM-26LR 25,000 0.40 ø 36 x 167 0.46 72 0.57 Rear 1⁄4 6 No
P-25A 25,000 0.44 ø 35 x 160 0.40 84 0.63 Front 1⁄4 6 No
http://www.atagroup.coMade in Ireland
40
ANGLE SANDER
ModelRPM Power
(HP)Dimension:
D x L X H (mm)Weight
(kg)dBA Air Cons
(m3/min)Disc : mm (in) Inlet (in) Hose
Included (m)Dia Bore
RA-2 2,700 1.10 ø 40 x 279 x 95 2.75 68 0.92 178 (7) 22 (7⁄8) 1⁄4 No
RA-5 5,500 1.10 ø 40 x 279 x 95 2.75 69 0.92 178 (7) 22 (7⁄8) 1⁄4 No
RA-2 - 2,700RPM RA-5 - 5,500RPM
ANGLE GRINDER
ModelRPM Power
(HP)Dimension: H x L (mm)
Weight (kg)
dBA Air Cons (m3/min)
Disc : mm (in) Inlet (in) Hose Included (m)Dia Bore
RA-14-100-PA1 15,000 1.50 85 x 261 1.9 79 1.13 100 (4) 16 (5⁄8) 1⁄2 No
RA-8 8,500 2.00 120 x 326 3.5 79 1.90 178 (7) 22 (7⁄8) 3⁄4 No
RA-14-100PA4 - 15,000RPM RA-8 - 8,500RPM
Model RPM Power (HP)
Head Height (mm)
Weight (kg)
Length (mm)
Sanding belt (mm)
dBA Air Cons (m3/min)
Exhaust Outlet
Inlet (in)
Hose Included (m)
BLM-16L 16,000 0.50 120 1.30 350 20 x 480 73 0.60 Front 1⁄4 No
RALM-20L 20,000 0.40 75 0.85 278 12 x 305 74 0.57 Rear 1⁄4 3
BLM-16L RALM-20L
BELT SANDER
41
Made in Irelandhttp://www.atagroup.co
Engravepen
SMD Series Anti-Vibration GrindersFeatures:• Ergonomically designed safety trigger improves levels of operator comfort• Improved air motor design for greater efficiency and power• Anti-vibration design for greater operator’s comfort
MODEL RPM Power (HP)
Dimension Weight (kg)
dBA Air Cons (m3/min)
Exhaust Outlet
SMD-25LR 25,000 1.1 ø 44 x 206 0.80 77 0.62 Rear
radiusburr CombiBurr
Design: Unique inverted curve which is ideal for creating smooth radius on sharp corners
Design: Bringing together an inverted cone and a ball shape onto one carbide burr
Radius Burr - CMN61225-2Head Diameter 12.7 mm
Head Length 25.0 mm
Cutting Length 16.0mm
Radius 20°
Shank 6.0 mm
Overall Length 70.0 mm
CombiBurr-DN61220-2Head Diameter 12.7 mm
Head Length 20.0 mm
Shank Diameter 6.0m
Overall Length 63.0m
SMD-25LR
Corner Radius Burr
The features of the Corner Radius Burr’s unique geometry provide the following benefits:
• Improves flute strength at the head of the burr• Improves burr control• Prevents digging into work piece at the intersecting point• Produces radius finish on the work piece• Reduces flute chipping at the intersection points
Design: A standard double cut (Cut 6) for general purpose use, which improves operator control and reduces the size of chips.
Corner Radius Burr A61225-6RAD
Head Diameter 12.7mm
Head Length 25.0mm
Shank Diameter 6.0mm
Overall Length 70.0mm
The Air Pen with solid carbide tip that writes on any hardened steel, glass and other hard surfaces. The Engravepen comes with a 2.5 metre hose.
Model EP400-1
Frequency (stroke/sec) 540
Dimension (mm) ø 17 x 140
Weight (kg) 0.15
dBA 65
Air Cons (m3/min) 0.02
Exhaust Outlet Rear
TUNGSTEN CARBIDE BURR
http://www.atagroup.coMade in Ireland
42
is an internationally renowed brand of high quality carbide burrs, and
forms a key part of the ATA Group, a privately owned organisation with over 50
years experience in the supply of metal working solutions to all major industrial
sectors
We are committed to provide our customers with high performance products
that maximise productivity and reduce costs. ATA’s headquarters and global
production centre is based in Cavan, Ireland, is accredited to ISO9001:2008
and equipped with the latest CNC technology delivering product of unrivalled
quality and consistency.
Cut Selection Guide1 2 3 4 5 6 8 9 10
Coarse cut for metal removal and finishing applications
on non-ferrous metal alloys
Standard cut for general application
Fast Mill cut for rapid
stock removal of softer
non-ferrous materials including plastics
Fine cut for improved finish on all ferrous
metals.
Foundry cut for stock
removal, rough edges suitable
for shipyard & foundry
applications
Double cut for general
purpose use. Improves control &
reduces chips.
Diamond cut for hardest materials &
best finishes
Chipbreaker cut for fast
stock removal. Improves
control and surface finish
Fast Mill cut with chipbreak-
er for rapid stock removal
Aluminum, Plastic
Brass, Copper, Cast Iron, Bronze
Unhardened Steel
Hardened Steel, Stainless Steel, Nimonic Alloys, TitaniumRecommended Highly recommended
Burr Set
BS2 - 8 Piece Burr Set (6mm Shank / Cut 6)
BS1A - 10 Piece Burr Set (3mm Shank / Cut 6)
BS1 - 20 Piece Burr Set (3mm Shank / Cut 2 and Cut 4)
BS1A - 10 Piece Burr Set (3mm Shank / Cut 6)
RimA6122.6-2 12.0 2.6 6A62006-6 19.0 6.0 6A62505-6 25.0 5.0 6
43
http://www.atagroup.coMade in Ireland
Whatever your concerns, offers the solution. e.g. extended shank are available upon request.
Part No. Head Dia
(mm)
Head Length (mm)
Shank Dia. (mm)
Sketch
FlameH30306 3.0 6.0 3 HH30612 6.0 10.0 3H60820 8.0 19.0 6H61020 9.6 19.0 6H61232* 12.7 32.0 6H61535* 16.0 36.0 6H62042* 19.0 41.0 6
60°/90° CountersinkJ60606 6.0 4.0 6 J/KJ61008 9.6 8.0 6J61210* 12.7 11.0 6J61512* 16.0 14.5 6J62018* 19.0 17.5 6K30303 3.0 1.5 3K60603 6.0 3.0 6K61004 9.6 4.7 6K61206* 12.7 6.3 6K61508* 16.0 8.0 6K62012* 19.0 9.5 6
Ball Nose ConeL30310 3.0 10.0 3 LL30312 3.0 14.0 3L60618 6.0 18.0 6L60822 8.0 25.4 6L61026 9.6 30.0 6L61228* 12.7 32.0 6L61533* 16.0 33.0 6L62038* 19.0 41.0 6
ConeM30311 3.0 11.0 3 MM30315 3.0 15.0 3M30612 6.3 12.7 3M60620 6.0 20.0 6M61020 9.6 16.0 6M61222* 12.7 22.0 6M61525* 16.0 25.0 6
Inverted ConeN30304 3.0 4.0 3 NN30606 6.3 6.0 3N60606 6.0 8.0 6N61010 9.6 9.5 6N61212* 12.7 12.7 6N61520* 16.0 19.0 6N62015* 19.0 16.0 6
Part No. Head Dia
(mm)
Head Length (mm)
Shank Dia. (mm)
Sketch
CylinderA30211 2.0 11.0 3 AA30314 3.0 14.0 3A30605 6.3 4.7 3A30612 6.3 12.7 3A60618 6.0 18.0 6A60820 8.0 19.0 6A61020 9.6 19.0 6A61220 12.7 19.0 6A61225* 12.7 25.0 6A61525* 16.0 25.0 6A62025* 19.0 25.0 6A62525* 25.0 25.0 6
Cylinder with EndcutB30211 2.0 11.0 3 BB30314 3.0 14.0 3B30605 6.3 4.7 3B30612 6.3 12.7 3B60618 6.0 18.0 6B60820 8.0 19.0 6B61020 9.6 19.0 6B61225* 12.7 25.0 6B61525* 16.0 25.0 6B62025* 19.0 25.0 6B62525* 25.0 25.0 6
Ball Nosed CylinderC30211 2.0 11.0 3 CC30312 3.0 14.0 3C30612 6.3 12.7 3C60618 6.0 18.0 6C60820 8.0 19.0 6C61020 9.6 19.0 6C61125 11.0 25.0 6C61225* 12.7 25.0 6C61525* 16.0 25.0 6C62025* 19.0 25.0 6
Part No. Head Dia
(mm)
Head Length (mm)
Shank Dia. (mm)
Sketch
BallD30202 2.0 1.8 3 DD30303 3.0 2.5 3D30404 4.0 3.4 3D30505 5.0 4.7 3D30606 6.3 5.0 3D60606 6.0 4.7 6D60808 8.0 6.0 6D61010 9.6 8.0 6D61111 11.0 9.5 6D61212* 12.7 11.0 6D61515* 16.0 14.0 6D62020* 19.0 16.5 6D62525* 25.0 22.0 6
OvalE30306 3.0 6.0 3 EE30610 6.3 9.5 3E60610 6.0 10.0 6E60815 8.0 15.0 6E61015 9.6 16.0 6E61220* 12.7 22.0 6E61525* 16.0 25.0 6E62025* 19.0 25.0 6
Ball Nosed TreeF30308 3.0 8.0 3 FF30312 3.0 14.0 3F30612 6.3 12.7 3F60618 6.0 18.0 6F60820 8.0 20.0 6F61020 9.6 19.0 6F61220 12.7 19.0 6F61225* 12.7 25.0 6F61525* 16.0 25.0 6F62025* 19.0 25.0 6F62032* 19.0 32.0 6
Pointed TreeG30312 3.0 14.0 3 GG30612 6.3 12.7 3G60618 6.0 18.0 6G60820 8.0 19.0 6G61020 9.6 19.0 6G61220 12.7 19.0 6G61225* 12.7 25.0 6G61525* 16.0 25.0 6G62025* 19.0 25.0 6
* Options: 8mm shank available upon request
ABRASIVES
44
Diameter x Width x Shaft (mm)
Speed (rpm)
15 x 15 x 625,00020 x 10 x 6
20 x 15 x 625 x 25 x 6
25,00030 x 05 x 630 x 10 x 630 x 15 x 630 x 30 x 640 x 05 x 6
19,00040 x 10 x 640 x 15 x 640 x 20 x 6
Diameter x Width x Shaft (mm)
Speed (rpm)
50 x 05 x 6
15,00050 x 10 x 650 x 20 x 650 x 30 x 660 x 10 x 6
12,60060 x 15 x 660 x 30 x 660 x 40 x 680 x 10 x 6
9,50080 x 20 x 680 x 30 x 680 x 40 x 6
Diameter x Width x Shaft (mm)
Speed (rpm)
30 x 15 x 615,000
40 x 25 x 650 x 30 x 6 12,000
Diameter x Width x Shaft (mm)
Speed (rpm)
60 x 30 x 6 10,00075 x 45 x 6
7,00080 x 40 x 6
Diameter x Width x Shaft (mm)
Speed (rpm)
100 x 25 x 12
5,400
115 x 25 x 12125 x 25 x 12150 x 25 x 12150 x 50 x 12
150 x 50 x 25.4
Diameter x Width x Shaft (mm)
Speed (rpm)
165 x 25 x 125,000
165 x 50 x 12165 x 50 x 25.4200 x 25 x 12
4,500200 x 50 x 12200 x 50 x 25.4
Grit: P40 to P320FLAP WHEEL with SHANK
**Other sizes can be made on request
FINISHING WHEEL
FLAP WHEEL
• Fan shaped abrasives for contoured metal surface grinding or finishing
• Full nylon flaps or with abrasive cloth combination for buffing and surface finishing
CNS BLACK DISC
SANDING DISC
FLAP DISC
SANDING BELT CLOTH
• For stainless steel grinding, polishing for hairline or after welding
For removal of rust, grinding of metal surface prior seams weldingSizes (mm) : ø 100 x 10 (height) x 16 (ID)Max RPM: 13,700*Available in threaded lock
Sanding Paper disc of excellent performance on most surface with consistent quality finishingGrits : P16 to P400Diameter Sizes (in) : 5, 6, 7Available in : 5 holes, 6 holes, stick it/pressure sensitive adhesive or Velcro backing types
Cloth backed abrasive belt for different contours, materials and surface preparationGrits : P24 to P600Available in : Alum Oxide & ZirconiaSizes (mm) : 10 x 330, 12 x 305, 20 x 460, 20 x 520
Constant stock removal, grinding of stainless steel, mild steel, aluminium, copper after weldingSizes (mm) : ø 100 x 16 (ID)Max RPM : 13,700Available in : Alum Oxide Grits: P40 to P400 Zirconia Grits: P60 to P120 Premium Grits: P60 to P120*Other sizes can be made on request
Grit: P40 to P320
Grit: P40 to P320
Grit: Med, Fine, Very Fine
**Other sizes can be made on request
**Other sizes can be made on request
Others : Nylon Polishing Roll (Sizes : 6” x 46 mtr, 6” x 120 mtr), Hand pads (6” x 9”) & Disc (4”, 5” & 6”)Abrasive Non woven roll or pad forms for hairline finishing or cleaning
INDUSTRIAL BRUSHES
45
STEEL WIRE WHEEL BRUSH (Flexible Type)
CUP BRUSH (Flexible Type)
DISH BRUSH
WIRE BRUSH WITH SHANK
END BRUSH
CUP BRUSH WITH SHANK
Item No.
Diameter: mm(in)
Width (mm)
Length (mm)
Thread Hole: mm(in) Max RPM Remark
WW-15 38 (11⁄2) 10 8 13 (1⁄2) 6,000Medium face.
Material: Steel, Brass Coated or Stainless
Steel Type
WW-20 50 (2) 10 12 13 (1⁄2) 6,000WW-25 65 (21⁄2) 10 15 13 (1⁄2) 6,000WW-30 75 (3) 12 20 13 (1⁄2) 6,000WW-40 100 (4) 15 25 13 (1⁄2) 6,000
Item No. Diameter: mm(in)
Length (mm)
Thread Hole: mm(in) Max RPM Remark
CC-31 75 (3) 25 M10 x 1.5 12,500 CC-Type Air/Electric ToolsCCO-35 75 (3) 25 16 (5⁄8) 12,500 CCO-Type : Air ToolsCCO-45 100 (4) 30 16 (5⁄8) 9,000 CCO-Type : Air Tools
Item No. Diameter: mm(in)
Length (mm)
Thread Hole: mm(in) Max RPM Remark
VO-45 100 (4) 20 16 (5⁄8) 12,500 For Air Tools
Item No. Diameter: mm(in)
Width (mm)
Length (mm)
Shank (mm) Max RPM Remark
SWA-12 30 (11⁄4) 8 6 6 18,000For use on drills and high speed
electric tools
SWA-15 40 (11⁄2) 10 10 6 18,000SWA-20 50 (2) 12 12 6 15,000SWA-25 65 (21⁄2) 12 18 6 15,000SWA-30 75 (3) 13 20 6 12,000SWA-40 100 (4) 13 25 6 12,000
Item No. Diameter: mm(in)
Length (mm)
Overall Length
Shank (mm) Max RPM Remark
SE-02 6 (1⁄4) 20 70 6 20,000
For use on drills and high speed
electric tools
SE-03 10 (3⁄8) 20 70 6 20,000SE-04 12 (1⁄2) 25 75 6 20,000SE-05 16 (5⁄8) 25 75 6 20,000SE-06 20 (3⁄4) 25 75 6 20,000SE-10 25 (1) 25 75 6 20,000SE-140 20 (3⁄4) 25 75 6 20,000
Item No. Diameter: mm(in)
Length (mm)
Arbor Hole/Shank (mm)
Max RPM Remark
SC-15 40 (11⁄2) 20 6 4,500 For do it yourself typeSC-20 50 (2) 20 6 4,500
SC-25 65 (21⁄2) 25 6 4,500SC-30 75 (3) 25 6 4,500
CC-31 CCO-35CCO-45
46
INDUSTRIAL BRUSHES
http://lessmann.comMade in Germany
CUP BRUSH WITH SHANK
Model Diameter (mm)
Length (mm)
OAL (mm)
Shank (mm) Max RPM Material Length
(mm) Product Code
SE-05 17 22 65 6 20,000 Brass Coated 313 51LM452751
SE-10 23 25 68 6 18,000 Brass Coated 343 51LM453751
SES-10 23 25 68 6 18,000 Stainless Steel 260 51LM453361
KE-10 29 28 72 6 20,000 Twist Knot / Steel Wire 339 51LM456258
Model Diameter (mm)
Length (mm)
OAL (mm)
Shank (mm) Max RPM Material Product Code
SWA-20 50 12 10 - 12 6 15,000 Brass Coated 51LM415752
KSW-30 75 15 9 6 25,000 Twist Knot / Steel Wire 51LM417198
SWAS-20 50 12 10 6 15,000 Stainless Steel 51LM415362
SWAS-30 75 17.5 14 6 15,000 Stainless Steel 51LMM21833
Model Diameter (mm) Length (mm) Shank (mm) Max RPM Material Product Code
SC-15 40 20 6 10,500 Steel Wire 51LM434162
SC-20 50 20 6 4,500 Brass Coated, For DIY 51LMM22044
SCS-15 40 20 6 10,500 Stainless Steel 51LM434362
WHEEL BRUSH WITH SHANK
END BRUSH
Since 1948, Lessmann has been producing “Made in Germany” wire brushes at the production site in Oettingen/Bavaria.With Ultra-modern industrial facilities, permanent quality controls and high-skilled staff, Lessmann assures high brush quality with a large portfolio of more than 10,000 products.
* Other Industrial Brushes available upon request.
47
Standard Air Duster
AIRSET® AIR DUSTERThe “WORLD CLASS” Air Duster - Airset RSA 301003AIRSET by AMPLA air blow guns are designed and manufactured to satisfy the needs of compressed air cleaning.
Features:• Ergonomics Design comfortable for both left and right hand users• Soft-Touch Design suitable for long term uses• Low noise level: 73.4dB (with silencer)
TUCANO AIR DUSTER
Option: Silencer- Stock Code: 3903
Made in Italy
PRESSURE REDUCER
NOISE REDUCTION
- 40%
To ensure Workplace Safety and Health• Ergonomics Design for user comfort• Reliable and equip with energy savings feature• Built-in pressure reducer ensures constant
supply of low air pressure at 30psi• Silent operation with a noise output of 66.1dB• Suitable for enclosed workplace• Produce low noise when blow on any object• Nozzle length: 108mm
IMPROVED SAFETY
ENERGY SAVING- 50%
= + +
Nozzle - 100mmL130S- with silencer (3901)L130 - without silencer (3902)
Nozzle - 482mmL520S- with silencer (3905)L520 - without silencer (3904)
Nozzle - 1,000mmL1000- without silencer (3906)
Air Duster nozzle 100mm(32NV040)
Air Duster nozzle 270mm(32NV041)
Coil Hose Assembly(2m, 4m, 6m and 8m)-id 5mm x od 8mm-id 6.5mm x od 10mm-Max operating pressure: 10bar
Air Water Cleaning Gun with aluminium body and 1.2metre PVC hose (OD: 0.75cm)(320NV042)
Stock Code: 3907
AIR HOSE REEL
http://www.zeca.itMade in Italy
48
ZECA products are well known all over the world for the quality and technology, due to strict comformity to the EEC rules, and are CE-marked.
Model Hose ID(mm)
Hose Length (m)
Max Pressure (Bar)
Colour Temp. (°C) End Pipe Fitting
Weight (kg)
Casing
9100/6 6.0 5.5 + 1 12 Black/Yellow -5 to +40 1⁄4” M 2 PlasticAM80/8 8.0 9 + 1 15 Yellow/Grey -5 to +40 1⁄4" M 4.5 PlasticAM85/10 10.0 15 + 1 15 Yellow/Grey -5 to +40 3⁄8" M 8.0 PlasticAM86/10 10.0 24 + 1 15 Yellow/Dark Grey -5 to +50 3⁄8” M 10.0 PlasticAM86/13 12.5 15 + 1 15 Yellow/Dark Grey -5 to +50 1⁄2”M 10.0 Plastic813/8 8.0 10 + 2 12 Yellow -5 to +50 1⁄4" M 10.5 Aluminium813/10 10.0 7 + 2 12 Yellow -5 to +40 3⁄8" M 10.5 Aluminium8804 12.5 15 + 1 20 Black -5 to +50 1⁄2" 20.0 Aluminium
9100/6 AM80/8AM85/10
AM86/10AM86/13
813/8813/10
8804
Features• Suitable for transmission of air and cool water - up to 20 bar pressure• Compact, Modern and rugged design - high impact resistant plastic and aluminium casing• Factory durability testing for spring retraction• Easy to install - wall mount - bracket with pivot• Rachet stop device at every 50cm• High Quality Polyurethane Hose• Maintain and tidy working places with bright and matt finish yellow colour (optional grey)• All hose reels come complete with quick couplers and one metre incoming hose.
CABLE REEL WITH LAMP
RETRACTABLE CABLE REEL
Model Description Metres of Coiled Cable
Max Watt bulb
Lamp Protection Degree
Weight(kg)
Reel protection Degree
5907/328 230 V Cable reel with fluo lamp 328 230 Volt
14 + 1.5 11 IP 55 4.5 IP 42
5907/329 230 V Cable reel with LED lamp 329 230 Volt
14 + 1.5 30 Led IP 55 4.5 IP 42
5907/370 Cable Reel with lamp 370 14 + 1.5 60 IP 65 4.5 IP 425908/308 24V Cable reel with Transfo +
Fluo Lamp 308 24Volt14 + 1.5 11 IP 55 4.5 IP 42
Model No. of Conductor Voltage (V) Amperage (A)
Conductors section (mm2)
Weight (kg) Meters of Coiled Cable
4315 3 230/110 16 1.5 5.0 14 + 15822/XF 4 400 20 2.5 4.0 5.5 + 1.55825/XF 3 230/110 25 2.5 4.0 7 + 1.55834/XF 1 - 43 6.0 4.0 12.5 + 1.55838/XF 8 - 10 1.0 4.0 5.5 + 1.57315 3 230/110 16 1.5 10.0 25 + 27325 3 230/110 25 2.5 10.0 20 + 27525RNF 5 400 20 2.5 10.0 10 + 2
49
http://www.zeca.itMade in Italy
43155822/XF5825/XF5834/XF5838/XF
731573257525RNF
5907/328 5907/329
5907/370 5908/308
http://www.zeca.itMade in Italy
50
VALVE GRINDER Art. 209 RECHARGEABLE LAMP Art.345
LED RECHARGEABLE LAMP Art.342RECHARGEABLE LED LAMP Art.KB 140
An essential air grinder in any workshop for a quick valve grinding. • Robustly made• Light, practical and easy to handle• Able to control speed by adjusting air flow• Weighs 1.5kg only• Comes with ø22, 33 and 40 rubber suction pads
COB LED Rechargeable Lamp• Shock resistant (IK09)• Water and Dust resistant (IP 64)• 430 Lumen• 2.5hr operating time• Comes with 100/240 V charger
Portable Rechargeable Powerful LED Lamp
Handy & Rugged for Inspection jobs in dark and wet places (IP64)
Other Features:• Shock resistant (IK09)• Water and Dust resistant (IP 64)• 160 Lumen• 9.0hr operating time• Comes with 100/240 V charger
SMB Rechargeable LED Lamp
Features:• Compact and Easy to Handle• Adjustable body up to 150º• Magnetic base and body• Battery Indicator Display• Integrated extractable hook• Comes with 100/240 V USB charger
SPRING BALANCERS
Model Capacity (kg) Travel (mm) Weight (g) Packing Weight (kg)
630 0.4-1 1,600 630 0.7631 1-2 1,600 670 0.8632 2-3 1,600 790 0.9633 2-4 2,500 2,850 3.2634 4-6 2,500 3,000 3.3635 6-8 2,500 3,100 3.4636 8-10 2,500 3,200 3.5637 10-14 2,500 3,500 3.8
Manufactured according to Directive 2006/42/CE, and to International Standards DIN 15112ISO EN 12100-1ISO EN 12100-2
Features:• Die-cast aluminium case• Continuous capacity adjustment from max value to min. value• Cable travel easily adjusted for fitting every need• Two suspension points to guarantee max. safety
Dual light source Magnetic base & hook
USB charger Adjustable body
51
http://www.zeca.itMade in Italy
JUMBOZECA Portable Exhaust Gas Extractor Art . 673
BATTERY & ALTERNATOR TESTER Art. 210
Allow the mechanic to work on the vehicle with the engine running without causing air pollution.
Powered by: 220 Volt Engine (50Hz)Protection Degree: IP54Supplied with: 1.5m Power Cable (3 x 1.5mm2)Delivered with: 6m plasticized heat-resistant (130ºC) ducting hose (120mm diameter)Capacity: 410m3/hLength Outlet Hose: 18m (max)Height Outlet Hose: 12m (max)
Special Features:• Easy to adjust height and suction setting• Its quick fit collar allows easy disconnection when moving from one location to
another.
Art. 678 - Additional Ducting Hose (6 metres)
Modern microprocessor tester for batteries and alternators. Simple, fast, intuitive and accurate to use.
Features:• 12V Test• Test Time: 15 seconds• Suitable for standard batteries and with Gel
technology• Temperature Compensation• The test doesn’t run down the battery• Characters (2 x 16) display at high visibility,
with LED backlighting. • Weighs 1.5kg only
RADIATOR TESTER Art.415
• Pressure testing the cooling system of cars• Detects any leaks in the cooling system• Can be used on most Continental and
Japanese cars• weighs 2.0kg only
PETROL RECORDING COMPRESSOR TESTER Art. 362
DIESEL RECORDING COMPRESSOR TESTER Art. 363
• Include 50 spare cards, 5 spare rubbers and 1 adaptor
• Recording card with wide scale approximate 50mm of coated surface provides clear, accurate print out of test
• Possibility of recording 8 tests on the card (+2 optional ones)
• Quick connection system locates into the spark-plug hole and expands due to pressure in cylinder
• Tester incorporates an engine rotation control mechanism
• Weighs 2.4kg only
• Include 50 spare cards, 3 connectors, without dummy injectors
• Provides quick and accurate written information on compression and indicates the condition of the cylinder bores, pistons, rings, etc, before dismantling the engine
• Recording card with wide scale
• Possibility of recording on the card 8 tests (+2 optional ones)
• Quick connector system on dummy injectors, no spanners necessary
• Weighs 2.5kg only
Made in Japan
52
QUICK COUPLERSPart No. I.D. O.D.TN-5NR 5mm 8mmTN-6.5NR 6.5mm 10mmTN-8N 8mm 12mmTN-8.5N 8.5mm 12.5mmTN-9N 9mm 15mmSocket - TNTube Connection
Part No. I.D. O.D.JN-5N 5mm 8mmJN-6.5N 6.5mm 10mmJN-8N 8mm 12mmJN-8.5N 8.5mm 12.5mmJN-9N 9mm 15mmPlug - JNTube Connection
Part No. SizeTS-2NR 1/4"TS-3NR 3/8"TS-4NR 1/2"Socket - TSMale Thread
TT-2NR 1/4"TT-3NR 3/8"TT-4NR 1/2"
Socket - TTHose End
Part No. SizeJSL-02 1/4"JSL-03 3/8"JSL-04 1/2"Elbow Plug - JSLMale Thread
Part No. SizeJS-02 1/4"JS-03 3/8"JS-04 1/2"Plug - JSMale Thread
JT-02 1/4"JT-03 3/8"JT-04 1/2"
Plug - JTHose End
Part No. SizeJTL-02 1/4"JTL-03 3/8"JTL-04 1/2"Elbow Plug - JTLHose End
TL-1NR One to two socket connector(Twin socket)
JF-02 1/4"Plug - JFFemale Thread
TD-30HN - JoplaStar Air Duster is suitable for many applications such as blow drying, cooling and cleaning by air flow.
Why Jopla plastic couplers are better?
1. Weight is about 1⁄3 of metal type - greatly reduce
operator’s tiredness
2. NO RUST - Corrosion resistant
3. Easy Operation - One touch - connect & disconnect
4. Impact resistant - strong as metal couplers. Very high
durability plastic material used.
5. Can be used on other Japanese metal couplers.
6. Maximum Air Flow - Valve design system
7. Plastic prevent sparks in flammable atmosphere
Jopla couplers are about 1⁄3 the weight of metal couplers lighter weight will reduce operator’s tiredness and increase productivity.
Once touch - Jopla couplers coupled and uncoupled easily - higher productivity
JOPLASTAR AIR DUSTER & ACCESSORIES
Jopla couplerLighter & better
Metal coupler
Reasons why we choose JoplaStar• Full Trigger reduces
operator’s fingers fatigue• Flow controller knob• Complete with 140mm nozzle
for precise flow direction
Optional
Jet NozzleHollow fiber filter
TF-10N
FL-600R
FL-600E
Std Code Hose Size(in) SH (Hose Nipple)
22SH 1⁄4
23SH SS 3⁄8
24SH SS 1⁄2
44SH 1⁄2
46SH 3⁄4
Std Code Thread Size (in) SM (Male Thread)
22SM 1⁄4
23SM 3⁄8
24SM SS 1⁄2
44SM 1⁄2
Std Code Thread Size (in) SF (Female Thread)
22SF 1⁄4
23SF 3⁄8
24SF 1⁄2
Std Code Hose Size(in) PH (Hose Nipple)
22PH 1⁄4
23PH 3⁄8
24PH 1⁄2
44PH 1⁄2
46PH 3⁄4
Std Code Thread Size (in) PM (Male Thread)22PM 1⁄423PM 3⁄824PM 1⁄244PM 1⁄2
Std Code Thread Size (in) PF (Female Thread)22PF 1⁄423PF 3⁄824PF 1⁄2
Socket PLUG
NL-P-2One to Two Line Connector
53
YOSHIDA AIR TOOLS
http://www.yoshida-mfg.co.jpMade in Japan
NKC QUICK COUPLERS (Stainless steel option) Made in Japan
YA-4C-12F - Angle Grinder (Safety Lever)
YA-5K-20 - 120° Power Brush/Grinder ( Roll Throttle)
SS: Stainless steel option
YGT-6 - Mini Palm Grinder
YA-5K-2F - 120° Power Brush/Grinder (Safety Lever)
ModelType RPM Wheel Size
(mm)OAL (mm)
Height (mm)
Weight (kg)
Max. Air Cons(m3/
min)
Hose Size (mm)
Air Inlet (in)
YA-4C-12F Lever 12,500 100 x 6 x 16 246 77.0 2.01 0.68 9.5 3/8
YA-5K-20 Roll 8,400 125 x 16 233 (200) 81.5 1.50 0.95 12.7 3/8
YA-5K-2F Lever 8,400 125 x 16 261 (227) 81.5 1.63 0.95 12.7 3/8
YGT-6 Lever 20,000 - 76 - 0.40 0.25 9.5 1/4
METAL CORE DRILLING MACHINE - ALFRA ROTABEST
http://www.alfra.deMade in Germany
54
Good reasons to decide on ALFRA Rotabest
• Magnetic Base Clamp has 3 coils (other standard 2 coils) and coupled with new M.P.I. Magnet System (MPI), which electronically increases magnetic adhesion at the start of the drilling operation, where strongest adhesion is required (for an even higher protection of user and tool).
• Powerful Motors with high torques and a range from 1,100 to 2,500W ergonomic design, perfect technology.
• Oil-bath Gearbox
• Soft-touch Grip, Low-vibration - with optimum secure grip (even with oil-coated gloves).
• Pressed-in brass rings for an improved protection of the magnet coils.
• Continuously adjustable motor on the slide for a maximum stroke enlargement, when using twist drills, drill chucks and tapping attachments.
• Durable keyboard with flat cable. Panel slopingly arranged, directly in sight of the user. To feel for the ON/OFF-switch has come to an end. Easy access to keyboard, even in narrow U-beams and H-beams.
• Newly designed gear housing with integrated motor support. With built-in height adjustment by means of clamping jaws - there is no better fixing device.
• Trouble with ordinary dovetail or pillar guides? Solid brass guide rails guarantee an optimum slide guidance
• The heart of the Magnetic Drilling Machines: Robust electronic switch units, interchangeable between Model RB 35SP, RB 50SP, 40 RL-E, 60 RL-E and 100 RL-E.
ROTABEST SERIES OVERVIEWType RB 35SP RB 50SP 40 RL-E 60 RL-E 100 RL-E 130 V32
Input (watt) 1,100 1,200 1,200 1,800 2,500 2,500 900
Speed (rpm) 450 250/450 100-250 180-450
50-110/75-175/105-245/
165-385
50-110/75-175105-245/165-385
30-80 / 50-120130-350 / 210-550 450
Max ø of cutter (mm) 35 50 50 80 100 130 32
Max Cutting Depth (mm) 50 50 50 50/110 50/110 50/110 30
Magnetic Adhesion(N) 8,000 8,000 16,000 20,000
30° swiveling20,000
30° swiveling 32,000 16,000
Min. Material Thickness (mm) 2 2 10 10 10 10 6
Size of Magnetic Foot: L x B (mm) 70 x 220 70 x 220 80 x 230 80 x 230 80 x 230 90 x 400 80 x 230
Stroke(mm) 105 100 170 190 245 230 45
Motor adjustable in Height(mm) 80 47 100 60 116 100 N.A.
Weight (kg) 9.9 11.5 16 22 28 34.5 12.5
Voltage 230v, 50/60Hz 230v, 50/60Hz 230v, 50/60Hz 110v 50/60Hz230v, 50/60Hz 230v, 50/60Hz 230v, 50/60Hz 230v, 50/60Hz
227.5MM
Rotabest 60 RL-ERotabest 100 RL-E
Rotabest V32
Rotabest RB35SP
ALFRA ROTABEST® - HSS-Co-Eco Cutters with Weldon Shank 19.0mm
55
ALFRA ROTABEST® - TCT Cutters with Weldon Shank 19.0mm
ACCESSORIES
Ejector Pin (mm) 2890A 2890B 2890C 2890D 2891A 2892A 2892B 2892CDimension ø 6.35 x 77 6.35 x 87 6.35 x 102 6.35 x 130 7.98 x 130 8 x 87 8 x 102 8 x 160
HSS Cutter ø 12 - 60 12 - 40 12-60 20 - 50
HSS Cutting Depth 25 35 50 110
TCT Cutter ø 12 - 17 12 - 17 14 - 17 18 - 100 18 - 100 18 - 100 18 - 100
TCT Cutting Depth 35 50 75 75 35 50 110
• With Weldon Shank 19.0 mm, 2 clamping surfaces• Available in cutting depths of 30mm, 35mm, 50mm, 75mm and 110mm• Available in cutting diameters from 12mm to 60mm• Internal bore: 6.35mm• Steel quality: Special high-capacity speed steel, cobalt• Ground section: High performance toothing with pre-cutter and post cutter
• With Weldon Shank 19.0mm• Internal bore: ø 14-17mm = 6.35mm, ø18-50mm = 8.0mm• Perfectly suitable for wear intensive applications• Available in cutting depths of 35mm and 50mm• Available in cutting diameter from 14mm to 100mm
High cutting performance toothing with 1. Pre-cutter2. Post-cutter
ALFRA “Chip-breaker system”1. Pre-cutter2. Middle-cutter3. Post-cutter
Description Product No. RB 35SP RB 50SP 40 RL-E 60 RL-E 100 RL-EDrill Chuck with weldon shank for twist drills
ø1-13mm2822
Quick-clamp chuck with Morse taper 2 & 3 for twist drills ø1-16mm
MT-2(2820) MT-3(2821)
MT-2 MT-2 MT-3 MT-3
Tool Holder AMK-2 - Morse Taper 2 for ø12-60mm 2808
Tool Holder AMK-3 - Morse Taper 3 for ø12-60mm. 2809
Tool Holder - Morse Taper 3 for ø61mm and above 2810
Tool Holder - Morse Taper 3 for ø12-50mm, Cutting depth 110mm
2810L
Quick change tapping adaptor MT-2 for Tap Collets M4-M14
(Optional)2818
Quick change tapping adaptor MT-3 for Tap Collets M6-M30
(Optional)2819
1
2
1
2
3
Suitable for
http://www.alfra.deMade in Germany
Optional: Do not come with the Tool
Prod.-No. 2822 Prod.-No. 2820/2821 Prod.-No. 2818/2819Prod.-No. 2808/2809/2810/2810L
Ejector Pins
(Optional) Tapping Adaptor
Quick Change Tapping Adaptor
Individual Tap Collet Size
POLY-PTX® 800 PROFESSIONAL COMPLETE SET (5801B)
http://www.www.eisenblaetter.de/Made in Germany
56
First class high-tech grinding and polishing equipmentFeatures:
• Mirror Finish in just 3 steps• Grinds from rough to very fine finishes• Hairline finishing in 1 simple step• Polishes stainless Steel Pipe• Variable Speed Control
SpecificationGrinding Speed (rpm) 1,000 - 3,500
Motor (Watt) 1,750Voltage 220V, 50/60Hz
Grinding Width (mm) 100Weight (kg) 3.3
ACCESSORIESAccessories Applications Dimensions
Eco Flap Wheel For removing rust, oxide layers, scratches and paint for regraining and burnishing metals
ø 105mm x 100mm (Grit: 40, 50, 60, 80, 120, 180, 240)
Eco Fleece Wheel For the shadow-free completion of industrial grinding finishes (matt and satin), pre-polishing, removing oxide layers and for smoothing "preground" sheets
ø 105mm x 100mm (Grit: 60, 80, 180, 280, 400, 600, 900)
Zirconium Grinding Sleeve
Removal of deep scratches, rust, scale and welds. Far less rework is required as a result of using the time-saving linear grinding technique.
ø 90mm x 100mm (Grit: 36, 40, 60, 80, 120, 150, 180)
Trizact Pyramid Sleeve Very high material removal whilst producing a very fine finish. Ideal for removing scratches and for pregrinding for polishing to a mirror finish
ø 90mm x 100mm A160 - Grit 120 A45 - Grit 600A100 - Grit 220 A10 - Grit 1200A65 - Grit 280 A06 - Grit 2000A45 - Grit 400
SC Fleece For removing minor scratches and oxide layers, matt and satin finishes, deburring and final grinding
ø 90mm x 100mm Coarse - Grit 80 Medium - Grit 180Fine - Grit 280Super Fine - Grit 400
Super Polish Sleeve For perfect brilliant, shadow-free mirror finishes. Super Polish fleece is absorbent, does not smear and save a lot of time. Only for use with polishing pastes or cream
ø 90mm x 100mm
Mirror Finishing Ring soft For the final polish - ideal mirror finish effect. Only for the use with polishing pastes or cream.
ø 100mm x 10mm
Adaptor for Eco Smart Abrasives
Adaptor for using Eco Smart abrasive with the POLY-PTX 800 ø 45 mm, internal ø 19mm with two keyways; width 100mm
Expansion Roller For use with Zirconium, Trizact TM, SC Fleece, Felt and SuperPolish sleeves. Highly elastic due to patented segment design. This ensuring perfect work-place adjustment and very simple sleeve changing
ø 90mm x 100mm
POLY-PTX® 800 Basic Machine (5801A)
57
SpecificationGrinding Speed (rpm) 1,000-3,500
Motor (Watt) 1,750Voltage 230V, 50/60Hz
Grinding Width (mm) 100Weight (kg) 3.3
Completes with ECO adaptor and Fleece wheel Grit 80.
Quintuple Swiveling handle for right and left handers. Vibration Reduction Handle for fatigue-
free work.
Rubberised handle for optimum and anti-slip handling.
Convenient Speed regulation during operation with
speedometer generator for constant speed under load.
QUICK-LOCK Cable quick connection for fast convenient
change.
Dustproof field coil through special coating
VARILEX® WSF 1800 Professional (5802)
PIPE-MAX 802 HT (5803A)
Specification
Grinding Speed (rpm) 2,000 - 7,600
Wheel Diameter (mm) Ø115 - 180
Thread M14
Motor (watt) 1,750
Voltage 230V 50/60Hz
Weight (kg) 2.8
Features:
• Ideal for grinding and polishing application• Can be used with flap discs, grinding and
cutting discs• Simple and fast changing of discs• Variable speed control
Specification
Grinding Speed (rpm) 820-3,000
Motor (watt) 1,750
Voltage 230V 50/60Hz
Weight (kg) 4.8
Belt Dimensions (mm) 40 x 780
Features:
• Perfect grinding and polishing on closed and open pipes• Fast, easy belt changing• Homogenous and uniform grinding• Adjustable Handle for both right or left handed operator
http://www.www.eisenblaetter.de/Made in Germany
Accessories
Special Zirconium Belt For grinding spot welds, eliminates deep scatches and rust - G40/60/80/120
SC Fleece Belt For removing minor scatches & oxide layers to produce matt and satin finish - Coarse G80, Medium G180, Fine G280, Superfine G400
Special Zirconium Belt
SC Fleece Belt
PNEUMATIC RIVETER AND NUT INSERT TOOL
http://www.far.bo.itMade in Italy
58
RAC-83/95 RAC-210 RAC-181• Rivet Capacity : 2.4mm to 4.8mm• Max Power : 535kg• Complete with 4 nozzles (2.4/3.2/4.0/4.8)• Weight: 1.4kg• IMPA: 61 52 51
• Rivet Capacity : 2.4mm to 4.8mm• Max Power : 725kg• 2-way nail ejection - front and rear• Complete with 4 nozzles (2.4/3.2/4.0/4.8)• Weight: 1.7kg • IMPA: 61 52 51
• Rivet Capacity : 2.4mm to 6.0mm (aluminium)• Max Power : 1,100kg• 2-way nail ejection - front and rear• Complete with 6 nozzles (2.4/3.2/4.0/4.8/5.0/5.8)• Weight: 1.6kg • Can use for Stainless Steel Rivets (3.0mm-4.8mm)
RAC-230Angular Head (Optional Accessory)• Rivet Capacity : 2.4mm to 4.8mm
• Max Power : 960kg• Complete with 4 nozzles (2.4/3.2/4.0/4.8)• Weight: 1.6kg
• Rivet Capacity : 2.4mm to 4.0mm• To be used in confined area
RAC-171 KJ-60 KJ-45/S• Rivet Capacity : 4.8mm to 7.8mm** (**Aluminium Only)• Max Power : 1,750kg• 2-way nail ejection - front and rear• Complete with 4 nozzles (4.8/5.0/6.4/7.8)• Magna Lok/Monobolt rivet: 3⁄16” to 1⁄4”• Weight: 2.93kg• Can use for Stainless Steel Rivets
(4.8mm-6.4mm)
• Capacity : M3 / M4 / M5 / M6 / M8 • Max Power : 1,450kg• Weight: 2.1kg
• Capacity : M4 / M5 / M6 / M8 / M10 / M12• Max Power : 2,798kg• Weight: 2.86kg
K-1 Manual (Hand Riveter)• Rivet Capacity : 2.4mm to 4.8mm• IMPA: 61 52 33
PORTABLE AIR CLEANER - UNI Series
59
Model Suction Airflow (m3/h)
Flitration Surface
(m2)
Filtration Efficiency
(%)
Motor Power
(kW/HP)
Power Supply (Volt)
Noise Level (dBA)
Dimension: L x W x H
(mm)
Total Weight (kg)
UNI 2.0 1,480 14.5 99.5 1.1 /1.5 230 / 50 70 800 x 600 x 1,200
105
Replacement Filter for UNI 2.0FILTRATION STAGE TYPE AND NAME PRODUCT CODE
A
Metal Filter Cell
3971CP(Consists of A, B and C)
B
Corrugated Filter Cell
C
Glass Microfibre Rigid Pocket Bag Filter
D (Optional)
Carbon Filter 3971CP-1
http://www.aerservice.itMade in Italy
The perfect solution for fume extraction.Features:
• High Filter Efficiency (<99.5%)
• Portability (Trolley Mounted)
• Low Noise Level (70dBA) : Like office condition
• Easy Maintenance: Reduce downtime and save cost
• Large Operating Area: 3 metre articulated arm of diameter 160mm to reach tight corner
60
S/No. Part No. TOKU Tools Model Shank Size (mm) Overall Length (mm)
Description Sketch
1 M1S TPB-60 / 73/ 90 11⁄4"H x 61⁄4" 550
Moil Point
2 M1 TPB-60 / 73/ 90 11⁄4”H x 61⁄4” 6203 M1L TPB-60 / 73/ 90 11⁄4”H x 61⁄4” 7604 M4 TPB-30/40 & TCD-30 1"H x 41⁄4" 5805 M4L TPB-30/40 & TCD-30 1”H x 41⁄4” 1,3306 M9 TCD-20 & PLA-10 22H x 83 4807 M9L TCD-20 & PLA-10 22H x 83 7108 M9LL TCD-20 & PLA-10 22H x 83 1,1009 C1 TPB-60 / 73/ 90 11⁄4”H x 61⁄4” 610
Chisel - Narrow10 C2 TPB-50N / 230N 11⁄8”H x 61⁄4” 61011 C4S TPB-30/40 & TCD-30 1” H x 41⁄4” 50012 C9 TCD-20 & PLA-10 22H x 83 47513 D1 TPB-60 / 73/ 90 11⁄4”H x 61⁄4” 570
Digger Chisel14 D2 TPB-50N / 230N 11⁄8”H x 61⁄4” 580
15 D4 TPB-30/40 & TCD-30 1” H x 41⁄4” 500
16 DW1 TPB-60 / 73/ 90 11⁄4”H x 61⁄4” 545Digger Spade
17 DW4 TPB-30/40 & TCD-30 1” H x 41⁄4” 490
18 S9 TCD-20 7⁄8”H x 31⁄4” 475 Spade 4”
19 A1 TPB-60 / 73/ 90 1 1/4"H x 6" 540
Asphalt Cutter20 A4 TPB-30/40 & TCD-30 1" H x 4 1/4" 505
CHISELS & MOIL POINTS
Made in Japan and Taiwan
S/No. Part No. TOKU Tools Model Shank Size (mm) Overall Length (mm) Description Sketch
22 M3N AA-3B, AA-1.3B & THA-4SRV 15H x 60 300
Moil Point23 M3NL AA-3B, AA-1.3B & THA-4SRV 15H x 60 600
24 M8N / M8L AA-0B 12H x 53 220 / 300
25 C3N AA-3B, AA-1.3B & THA-4SRV 15H x 60 300Chisel- Narrow26 C3NL AA-3B, AA-1.3B & THA-4SRV 15H x 60 600
27 C8N/C8L AA-0B 12H x 53 220/310
28 M5N MH-5111/5115 & BRH-3 10R x 40 200
Moil Point29 M7/M7N TCA-7 & G-9S 26R x 80 400/450
30 M7L TCA-7 & G-9S 26R x 80 600
31 M7LL TCA-7 & G-9S 26R x 80 1,200
32 C5N MH-5111/5115 & BRH-3 10R x 40 200 Chisel - Narrow33 C7 TCA-7 & G-9S 26R x 80 400
34 D3 AA-3B, AA-1.3B & THA-4SRV 15H x 60 290Asphalt Cutter
35 D7 TCA-7 & G-9S 26R x 80 450
36 M23 TCB-200 30R x 87mm 400Moil Point
37 M33 TCB-300 35R x 87mm 465
38 C23 TCB-200 30R x 87mm 400Chisel-Narrow
39 C33 TCB-300 35R x 87mm 455
Chisel Accessories in our Quality Package have been carefully selected from international manufacturers to ensure that you get the best value for your orders.
Note: Overall Length (OA) may vary about 5% due to manufacturing process H : Hexagon R : Round
CHISELS & MOIL POINTS
Made in England
http://thomas-turton.co.ukMade in England
SMC-AIR TREATMENT SYSTEM - Filter Regulator Lubricator (F.R.L)
AIR LINE LUBRICATOR
AIR HOSES BARREL PUMP
If you have not installed a FRL (Air Treatment System) in your air supply system, we like to recommend that you install one to protect your air tools and other air-powered equipment. Air Treatment System can ensure longer and trouble-free operations for air products.
Filter Regulator Lubricator (FRL)
Filter (F) Regulator (R) Lubricator (L) - Also available in 11⁄2” and 2” inlet
SR-3- Adjustable 1/4”Air RegulatorTo regulate air flow and control air tool speed and power
Filter-Regulator & Lubricator (FR+L)
Size Code 20 30 40 50 60Air Inlet Size (Inch) BSP thread 1⁄4 3⁄8 1⁄2 3⁄4 1
Max. Flow Rate (L/min) 800 1,500 3,000 6,000 7,000
Operating Temp. Range (°C) Temperature Range - 5°C to 50°C
Max. Operating Pressure 1.0MPA / 10 Bar
Weight (kg ) FRL Set 0.73 1.00 1.34 4.20 4.34
Model PL-400 PL-400LIn & Out 3/4” NPT 3/4” NPT
Oil Capacity (ml) 110 320
Air Flow (cfm) 70 70
Weight (kg) 0.63 1.08
Model EMLL 13In & Out 1” NPT
Oil Capacity (ml) 1,300
Air Flow (cfm) 100
Weight (kg) 2.52
These In-Line Lubricators are:-• Simple to install• Light and rugged in construction• Require minimum or no maintenance• For correct lubrication, in line lubricator should not
be more than 3.0m from the air tools
Yellow Hoses:• Flexible PVC Hose plasticised with interlaced polyester
thread reinforce• Resistant to weather agents and to most chemicals
Model BDP 10Net Weight (kg) 5.3
Overall Length (mm) 1,175
Min Opening Pump will enter (mm) 54
Air Inlet hose size (mm) 6.3
Air Consumption (m3/min) 0.34
Fluid Outlet Hose size (mm) 19
BDP 10
61
Made in USA
32NV050 - 1⁄4” PT- Mini Line Oiler
32NV051 - 3⁄8” PT- Mini Line Oiler
ID (mm) OD (mm) Length (m)
WP (PSI)
BP (PSI)
6.3 ( 1⁄4”) 12.0 100 250 1,000
10.0 ( 3⁄8”) 16.0 100 250 1,000
12.5 ( 1⁄2”) 19.0 100 250 1,000
19.0 ( 3⁄4”) 26.5 100 250 1,000
INDUSTRIAL AIR TOOLS
http://www.twairboss.comMade in Taiwan
62
Model Capacity (Grinding Wheel)
Collet size (mm)
Free speed (rpm)
Overall length (mm)
Net weight (kg) Air inlet (in) Air consumption
(m3/min)AG-50C-3 38 x 13 6 15,000 157 0.6 1⁄4 0.4
DG-26L-1 25 x 13 6 24,000 297 0.8 1⁄4 0.4
DG-26L-1BF 25 x 13 6 24,000 306 0.9 1⁄4 0.4
SG-65HL-1 65 x 13 x 9.6 - 12,000 522 1.9 3⁄8 0.6
SG-125HL-2 100 x 19 x 12.7 - 9,000 953 5.3 3⁄8 1.0
AB-10 Impact Screwdriver
DR-65Straight Drill
SG-65HL-1Extended Straight Grinder
SG-125HL-2 Extended Straight Grinder
AB-1700PShort Body Impact Wrench
129mm
AIRBOSS AIR TOOLS CO., LTD established in 2000, is a multi-award winning manufacturer in manufacturing professional pneumatic tools. The company has adopted modern CNC machines and newest, world-wide leading super vacuum-foundry technology in their manufacturing process.
Specifications: Air Pressure 6kg/cm2
Specifications: Air Pressure 6kg/cm2
295mm 585mm
AG-50C-3Angle Die Grinder
DG-26L-1Extended Die Grinder
DG-26L-1BFExtended Die Grinder (Safety Lever)
90m
m ø20x149mm
Model Capacity (mm)
Torque (Nm)
Free speed (rpm)
Overall length (mm)
Net weight (kg) Air inlet (in) Air consumption
(m3/min)AB-10 8-10 30-70 8,000 215 1.1 1⁄4 0.3
AB-1700P 15 34-306 7,600 129 1.5 1⁄4 0.3
DR-65 9.6 (3⁄8”) - 2,600 210 0.9 1⁄4 0.6
Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
ø20x148mm
APAC - Air Tools
63
http://www.masapac.com.twMade in Taiwan
Model Length (mm)
Net Weight (kg)
Free Speed (rpm)
Operating air pressure (psi)
Air Consumption (cfm)
Inlet (in)
Noise Level (dBA) Capacity
A11-E2927 240 0.7 22,000 90 3.1 1⁄4 79 1⁄4” or 6mm collet
A16-K0102 200 1.86 150 90 2 1⁄4 82Tapping: Aluminium
2-12mm, Copper 3-12mmm, Iron 3-8mm
A16-B0520 250 0.8 5,000 90 4 1⁄4 73.9 Cutting size-1.6mm
Model Length (mm)
Net Weight (kg)
Torque Range(Nm)
Free Speed(rpm) Drive size Inlet (in) Noise Level
(dBA) Type
AP-180 244 0.59 0.3 ~ 1.8 900 1⁄4 F/HEX 1⁄4 68 LeverAP-450 263 0.84 1.0 ~ 4.5 700 1⁄4 F/HEX 1⁄4 72 LeverAP1000 309 0.93 3.5 ~ 10.0 550 1⁄4 F/HEX 1⁄4 72 LeverAP180A 298 0.88 0.3 ~ 1.8 900 1⁄4 F/HEX 1⁄4 68 Angle HeadAP-450A 314 1.02 1.0 ~ 4.5 700 1⁄4 F/HEX 1⁄4 72 Angle HeadAP-1000A 350 1.36 3.5 ~ 10.0 550 1⁄4 F/HEX 1⁄4 72 Angle HeadAP-180P 198 0.77 0.3 ~ 1.8 900 1⁄4 F/HEX 1⁄4 68 PistolAP-450P 209 0.98 1.0 ~ 4.5 700 1⁄4 F/HEX 1⁄4 72 PistolAP-1000P 238 1.10 3.5 ~ 10.0 550 1⁄4 F/HEX 1⁄4 72 PistolAP-180PS 228 0.54 0.3 ~ 1.8 900 1⁄4 F/HEX 1⁄4 68 Push-startAP-450PS 244 0.77 1.0 ~ 4.5 700 1⁄4 F/HEX 1⁄4 72 Push-startAP-1000PS 276 0.89 3.5 ~ 10.0 550 1⁄4 F/HEX 1⁄4 72 Push-start
A16-K0102Air Tapper
A16-B0520Air Saw and File
Model a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
AP-180A 298 32 29.5 18 14.5
AP-450A 314 39 29.5 18 14.5
AP1000A 350 39 31.0 18 14.5
Model a (mm)
b (mm)
c (mm)
d (mm)
AP-180 244 32 10.4 16
AP-450 263 39 10.4 16
AP1000 309 39 10.4 16
Model a (mm)
b (mm)
c (mm)
d (mm)
AP-180PS 228 32 10.4 16
AP-450PS 244 39 10.4 16
AP1000PS 276 39 10.4 16
Model a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
AP-180P 198 161 144 10.4 16
AP-450P 209 167 147 10.4 16
AP1000P 238 167 147 10.4 16Push-start Type Pistol Type
Angle Head Type Lever Type
APAC - Shut-off Screw Driver
Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
A11-E29273” Die Grinder
64
SHUT OFF AIR OIL PULSE WRENCH-PISTOL TYPE
http://en.torerotool.comMade in Taiwan
NON SHUT-OFF OIL PULSE WRENCH-PISTOL TYPE
Model Bolt
Capacity (mm)
Torque Range (Nm)
Drive size (in)
Free speed (rpm)
Length (mm)
Net weight
(kg)
Air inlet (in)
Air hose size (mm)
Air consumption
(m3/min)
Noise level (dBA)
OBT-50PD 5-6 7-16 3⁄8 4,800 160.5 0.92 1⁄4 6.5 0.25 78OBT-60PD 8 20-32 3⁄8 6,000 170 0.95 1⁄4 8.0 0.35 80OBT-70PD 8-10 30-50 3⁄8 5,800 183 1.05 1⁄4 8.0 0.40 80OBT-80PD 8-10 42-60 3⁄8 6,000 187 1.25 1⁄4 8.0 0.48 80OBT-81PD 10 50-65 1⁄2 6,000 192 1.25 1⁄4 8.0 0.48 80OBT-90PD 10-12 55-85 1⁄2 4,800 192 1.45 1⁄4 8.0 0.53 82OBT-100PD 12 75-115 1⁄2 4,500 198 1.70 1⁄4 8.0 0.55 82OBT-130PD 12-14 90-145 1⁄2 3,800 215 2.30 1⁄4 12.7 0.70 82OBT-150PD 14-16 130-205 3⁄4 3,400 243.5 2.90 1⁄4 12.7 0.70 82
Model Bolt
Capacity (mm)
Torque Range (Nm)
Drive size (in)
Free speed (rpm)
Length (mm)
Net weight
(kg)
Air inlet (in)
Air hose size (mm)
Air consumption
(m3/min)
Noise level (dBA)
OBN-30PD 5-6 6-12 3⁄8 4,000 133 0.70 1⁄4 6.5 0.20 75OBN-40PD 6 13-22 3⁄8 4,000 133 0.70 1⁄4 6.5 0.20 75OBN-50PD 6-8 20-35 3⁄8 7,000 140 0.77 1⁄4 6.5 0.30 78OBN-60PD 8-10 35-50 3⁄8 6,500 140 0.82 1⁄4 8.0 0.40 80OBN-70PD 10 40-60 3⁄8 6,000 153 0.95 1⁄4 8.0 0.45 80OBN-90PD 12 80-100 1⁄2 5,200 170 1.30 1⁄4 8.0 0.53 82OBN-100PD 12-14 90-125 1⁄2 4,600 177 1.66 1⁄4 8.0 0.58 80
Features:1. Reliable torque precision and rapid shut-off effect2. Improvement of efficiency and reduction of cost3. Reduce labour intensity of operators4. Contribution to environmental protection - Low noise, low
vibration and small reaction force
OBN-50PD
OBT-50PDTorque: 1.0kg.m = 9.807Nm = 7.233ft.lb
Torque: 1.0kg.m = 9.807Nm = 7.233ft.lb
65
INDUSTRIAL CORDLESS SHUT OFF TOOLS
Made in Taiwan
Model SQ Dr (mm)
Hex Dr (mm)
Volt (V)
Screw Size (mm)
Torque Range (Nm)
FreeSpeed (rpm)
Weight (kg)
Length (mm)
Noise Level (dBA)
PW-35S3 9.5 (3⁄8") - 18 - 22.0 - 35.0 3500 1.74 242.8 <72SCT-6 - 6.0 (1⁄4") 18 M3 - M5 1.0 - 6.0 400 - 900 0.95 238.0 <75SCT-9 - 6.0 (1⁄4") 18 M3 - M5 1.5 - 9.0 300 - 800 0.95 238.0 <75SCT-12 - 6.0 (1⁄4") 18 M4 - M6 2.0 - 12.0 250 - 600 0.95 238.0 <75WRTBA-50S3 9.5 (3⁄8") - 18 M6 - M10 22.0 - 50.0 200 2.0 579.1 <75
AIR IMPULSE TOOLS
Model SQ Dr (mm)
Screw Size (mm)
Bolt Cap
Air Consumption (m3/min)
Torque Range (Nm)
FreeSpeed (rpm)
Weight (kg)
Length (mm)
Noise Level (dBA)
TDCS-30SL07 - M5 - 0.51 3.0 - 8.0 700 0.97 274 78TDCS-30SL17 - M4 - 0.51 2.0 - 4.5 1700 0.97 274 78TDIS-30 9.5 (3⁄8") - M6 0.25 6.5 - 13 4600 0.89 167 78TDIS-30S 9.5 (3⁄8") - M6 0.25 6.5 - 13 4200 0.8 221 78TDIS-50S 9.5 (3⁄8") - M8 0.35 14.0 - 28.0 6800 0.8 221 80
PW-35S3 - Shut off Wrench SCT 6/9/12 - Shut off Screwdriver WRTBA-50S3 - Shut off Screwdriver
TDCS-30SL07/17 - Air Screwdriver TDIS-30 - Shut off Wrench TDIS -30S/50S- Shut off Wrench
http://tranmax.com
Since established in 1985, Tranmax Machinery Co., Ltd. has devoted itself to manufacture and export high quality pneumatic tools for professional applications.New innovations and improvements are persistently made to meet market trends and demands. Tranmax has successfully earned popularity and has a sound reputation in world-wide markets due to their belief in manufacturing reliable products and delivering customer satisfaction.
66
HYDRAULIC POWER PACK
HYDRAULIC BREAKER
http://www.hycon.dkMade in Denmark
MODEL Oil Flow (l.p.m) Max. Pressure (bar)
Engine/Motor Starter Weight(kg)
Noise Level (dBA)
No. of Tools
HPP06 1x18 110 Honda 6.5 HP Petrol Recoil 54 88 1
HPP09 1x20 150 Honda 9.0HP Petrol Recoil 68 88 1
HPP13 FLEX 1x 20-30 150 Honda 13.0 HP Petrol Recoil 81 89 1
HPP18V FLEX 1x20-30-40 160 Vanguard 18.0HP Petrol Recoil & electric 105 89 1
HPP18VMF 2 x 10-15-20 160 Vanguard 18.0HP Petrol Recoil & electric 112 89 2
HPP13D FLEX 1x 20-30 150 Lombardini 11.0 HP Diesel Recoil & electric 114 93 1
HPP09E 1x20 150 5.5kW 16A/3x400V 50Hz Electric 80 85 1
HPP18E 1x30 or 1x40 160 11kW 25A, 35A/ 3x400V 50Hz Electric 128 86 1
HPP18E FLEX 1x20-30-40 160 11kW 35A / 3x400V 50Hz Electric 128 86 1
The hydraulic Hycon HPP-powerpacks are the power source of the hycon hydraulic system. the series of powerpacks complies with any demand on an efficient power source - irrespective of the size, the nature and the difficulty of the jobs. the HPP-powerpacks are characterised by a simple and sturdy modular construction with few wearing parts and an easily-accessible and user-friendly design.
The individual components of the powerpacks have been carefully selected after thorough tests on our testing facilities, and the entire HPP-series has a unique mounting quality and therefore a high reliability.
No instructions are required for the very simple operation of the powerpacks - this is one of the features that make this solution very suitable for the rental business. the hycon hydraulic system ensures flexibility, more power - and fuel consumption much lower than a compressor!
MODEL Oil Flow (l.p.m)
WorkingPressure
(bar)
Max.Pressure
(bar)
Blow frequency,
1/min
Tool Size(mm hex)
Weight(kg)
Noise Level (dBA)
HH10RV 20 100 160 2,100 19 x 50 9.9 93
HH15 20 100 160 1,830 22 x 82 15.3 93
HH20 / HH20RV 20 110 160 1,560 25 x 108 / 32 x 160 22.0 / 23.9 94
HH23 20 / 30 120 160 1,380 25 x 108 23.4 / 23.5 96
HH25 20 / 30 120 160 1,380 32 x 160 25.3 / 25.8 108
HH27 30 130 160 1,260 32 x 160 27.4 98
HH35 30 / 40 130 160 1,440 32 x 160 29.4 99
The Hycon HH-Series is the result of the strongest and most modern design on the market. our hydraulic quality breakers have practically only two moving parts, and this ensures minimum wear and consequently much lower operating costs.
The Hycon HH-Series is equipped with the world’s best vibration-dampening system as standard, the Hycon Proline handle. This handle gives unique operator comfort with a vibration level as low as 4.8 m/s2 (HH20RV), and the breaker can therefore be used efficiently 8 hours per day (ec-directive of 1 July 2005).
The reliability, the sturdy design and the supreme component quality of the Hycon HH-Series means long life under extreme working conditions!
67
http://www.hycon.dkMade in Denmark
• More powerful - against electric and Pneumatic Breakers• Lighter in weight - Ease of Handling• Low Noise - Reduce Noise Pollution• Moving parts are self-lubricated - Low maintenance cost• Save money and manpower - Higher productivity• Can be used in harsh conditions - e.g. In the rain
Why using Hydraulic Breaker can increase your PRODUCTIVITY? - Reduce Cost & your Manpower
HYDRAULIC RING SAWThe HYCON hydraulic ring saw offers you the most overall efficient and productive 300 mm deep cutting. All parts run in oil - no down time and service is next to nothing.
The HYCON ring saw has a unique design and state of the art drive mechanism that will give you many hours of use and long lasting wearing parts that will ensure you low operating cost. Investing in a ring saw is investing in more work because it will cut 300 mm deep compared to common petrol or hydraulic circular hand saws that only cut up to 187 mm. It is also investing in higher efficiency because it will cut 300 mm deep resulting in less work afterwards (e.g. a doorway) and less after work means job done faster and much cheaper!
FEATURES• Cut any concrete, bricks, stone, etc.also with rebar in 300 mm depth• Cutting of openings for doors and windows, cutting of pipes, etc.• Under water jobs• Very powerful - up to 18 HP• ASCO Safety System• Long lifetime - all parts run in oil• Ergonomic design - operator comfort• Easy change of discs• Lower vibrations and weight
MODEL Oil Flow (l.p.m) Cutting Depth (mm)
Diamond Disc Dia.
(mm)
Max. Pres-sure (bar)
Cutting speed (m/s)
Rotation Weight(kg)
Noise Level (dBA)
HRS400 30-40 300 400 160 37-49 1,750-2,350 10.9 109
68
CARRIER-MOUNTED SPLITTER - C20
Reasons to use Darda Splitters• Easy to operate
• Safe & Quiet Demolition
• Vibration & Dust Free
• Splitting Force of 358 ton per Split
• Cut Noise at work sites
http://www.darda.deMade in Germany
Type Wedge set
Required drill hole diameter
(mm)
Minimum drill hole
depth (mm)
Splitting Distance
(mm)
Splitting Force theoretical
Effective Splitting Force
Weight (kg)
Length of splitting
Cylinder (mm)
Length of wedge set
(mm)kN ton kN tonC9 N 45-48 410 18 - 53 2,995 305 1,962 200 22 1,020 230
C12 N 45-48 610 19 - 60 6,061 618 3,507 358 31 1,290 380C20C N / L 76 750 / 950 22 - 25 14,760/17,660 1,500/1,800 14,760 1,500 285 2,343 500/700C20V N / L 76 750 / 950 22 - 25 14,760/17,660 1,500/1,800 14,760 1,500 390 2,411 500/700C20H N / L 76 750 / 950 22 - 25 14,760/17,660 1,500/1,800 14,760 1,500 395 2,434 500/700C20J N / L 76 750 / 950 22 - 25 14,760/17,660 1,500/1,800 14,760 1,500 375 2,549 500/700
Optional Enlarging Wedge Set for a wider split.Use only Darda Special Grease to greatly reduce damage and breakage of wedge set - reduce down time and save money.
Cut Noise at work sites
HANDHELD ROCK SPLITTER - C9 and C12
C20V - Vertical type
C20C - Chain type
C20J - Joint Type
C20H - Horizontal type
Cut Noise at work sites
Features• Various mounting options
• Easy Insertion
• Rotatable and Versatile
• For Carries between 5-7tons
69
http://www.darda.deMade in Germany
HYDRAULIC POWER UNIT
HCS 8 Combi Shear:• High Power, Light-weight - only 15kg• Crushing Force: 8.6 ton• Cutting Force: 26.8 ton
Application:• Cut Metal bar and plate• Break concrete and masonry• Separate a wide range of materials
• AP-2: Air Motor• BP-2 Gasoline Engine• EP-2 Electric Motor (220v 1ph 50Hz)
(415v 3ph 50Hz)• D4 Diesel Engine
Features:• Two-stage pump (low and high pressure)
• Low pressure: 85Bar, High pressure: 500Bar
• Easy to transport with wheels and pull out handle
• Connection for up to 3 splitters
CRUSHER & SHEAR
Type Type of motor Supply Weight(kg)
Dimension (mm) Pump Capacity (l/min) Tank Vol. (litre)Length Width Height Low Pr High Pr
AP2 Air motor 6kg/cm2 40 600 398 426 5.0 1.6 5.0BP2 Gasoline engine Petrol 40 600 398 426 5.0 1.6 5.0EP2 Electric motor 400V 415V 40 600 398 426 5.0 1.6 5.0EP2 Electric motor 230V 220V 50 600 398 426 5.0 1.6 5.0D4 Diesel engine Diesel 137 1,180 720 730 5.4 5.4 10.0
Type of Jaw and Blade Cutting Force Breaking Force Separating Force Expanding Width (mm)
Depth of break
Weight approx (kg)
Overall Length (mm)kN ton kN ton kN ton
HCS 8 J - Concrete Jaw - - 86 8.6 - - 170 100 16.5 715HCS 8 B - Brick Jaw - - 41 4.1 27 2.7 320 105 15.5 795HCS 8 S - Sickle Blade 267 26.8 - - - - 90 80 14.5 660HCS 8 C - Shears 267 26.8 - - 70 7.0 250 - 15.0 720
HCS 8 J can crush concrete wall up to 15cm thick.
HCS 8 S cuts steel bar of Ø 16mm, and pipe of Ø 50mm x 1.5mm
HCS 8 B replaces the sledge hammer to break down brick wall 32cm
HCS 8 C cuts steel bar of Ø 20mm, and has a separating force 5.8 ton
HCS 8 with 4 types of Cutter
AP-2 Air Motor D4 Diesel Engine
For more information, Please check with your local distributor
Our Quality Package
We make our products work harder for you
EM-2020
Japan
Japan
Japan
JapanJapan
IrelandIrelandGermanyEngland
Germany Italy Italy Italy Germany
Germany Italy USADenmark
Singapore
JapanTaiwan Taiwan TaiwanGermany Germany
TaiwanEngland South KoreaJapan
ENTREPOT