OSD User Manual - CCTV Camera Pros (Open) ex BULLET (OSD cap) bottom type back type ex OSD control...
-
Upload
vuongkhanh -
Category
Documents
-
view
229 -
download
6
Transcript of OSD User Manual - CCTV Camera Pros (Open) ex BULLET (OSD cap) bottom type back type ex OSD control...
1080p AHD CCTV Camera
OSD User Manual
The 1080p CCTV cameras (AHD CCTV) that this manual applies to can be found on this page.
http://www.cctvcamerapros.com/1080p-HD-Security-Cameras-s/986.htm
1. You need to select the CVBS / AHD mode according to the specifications of DVT.
2. Before selecting the CVBS / AHD mode, please check the direction and position of the OSD operation buttons of the product.
3. CVBS / AHD mode cannot be selected in a state in which to turn on the OSD setting screen. So, you need to set them afte
closing the OSD setting screen.
If pressing the OSD button for 3 seconds to the left, it is set up (CVBS) output mode of the Analog.
If pressing the OSD button for 3 seconds to the right, it is set for n, it is set up output mode of the AHD.
OSD control buttons
AHD modeCVBS mode
Methods of operation by Product Type (Please check the position and direction of the OSD operation buttons)
PLASTIC DOME ex
VANDAL DOME ex
UP
DOWN
RIGHTLEFT
OSD control buttons
AHD modeCVBS mode
UP
DOWN
RIGHTLEFT
CVBS, AHD mode selection
BULLET (Open) ex
BULLET (OSD cap)
bottom type back type
ex
OSD control buttons are located inside of the product.
OSD control buttons
AHD modeCVBS mode
UP
DOWN
RIGHTLEFT
OSD control buttons
AHD modeCVBS mode
UP
DOWN
RIGHTLEFT
CVBS, AHD mode selection
Methods of operation by Product Type (Please check the position and direction of the OSD operation buttons)
1. You need to select the CVBS / AHD mode according to the specifications of DVT. 2. Before selecting the CVBS / AHD mode, please check the direction and position of the OSD operation buttons of the product. 3. CVBS / AHD mode cannot be selected in a state in which to turn on the OSD setting screen. So, you need to set them after closing the OSD setting screen.※There are two types of controlling OSD. One is control button type in product, the other type is to control the OSD after opening the CAP of OSD.
If pressing the OSD button for 3 seconds to the left, it is set up (CVBS) output mode of the Analog. If pressing the OSD button for 3 seconds to the right, it is set for n, it is set up output mode of the AHD.
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
NR
SPECIAL
ADJUST
EXIT
MANUAL DC
SHUTTER AGC SENS-UP BRIGHTNESS D-WDR
DEFOG RETURN
CAM TITLE D-EFFECT MOTION PRIVACY LANGUAGE
DEFECT RS485 RETURN
SHARPNESS MONITOR LSC VIDEO. OUT
DATA VER OUTPUT SIZE RETURN
SAVE&END NOT SAVE RESET
OFF BLC HSBLC
ATW AWC → SET INDOOR OUTDOOR MANUAL AWB
COLOR B/W EXT AUTO
2DNR 3DNR RETURN
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
LENS, EXPOSURE, BACKLIGHT, WHITE BAL, DAY&NIGHT, NR, SPECIAL, ADJUST,EXIT
MANUAL
OFFATWAUTO
SAVE&END
1. LENS
2. EXPOSURE
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
DC
OFFATWAUTO
SAVE&END
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
1. SHUTTER2. AGC3. SENS-UP4. BRIGHTNESS5. D-WDR6. DEFOG7. RETURN
EXPOSURE
AUTO 15OFF 40OFFOFFRET
0~15
Auto level control (x2 ~ x30)
AHD ( 1/30(25) ~ 1/50,000, x2, ~ x30 ) / CVBS ( 1/60(50) ~ 1/50,000, x2, ~ x30 )
1. SHUTTER2. AGC3. SENS-UP4. BRIGHTNESS5. D-WDR6. DEFOG7. RETURN
EXPOSURE
AUTO 15AUTO 40OFFOFFRET
1. SENS-UP2. RETURN
SENS-UP
x4RET
DEFOG :
D-WDR (Digital Wide Dynamic Range)
BRIGHTNESS : Brightness level control (0~100)
Brighten the image when it is foggy or cloudy
1. SHUTTER2. AGC3. SENS-UP4. BRIGHTNESS5. D-WDR6. DEFOG7. RETURN
EXPOSURE
AUTO 15OFF 40ONOFFRET
1. LEVEL2. RETURN
D-WDR
5RET
1. SHUTTER2. AGC3. SENS-UP4. BRIGHTNESS5. D-WDR6. DEFOG7. RETURN
EXPOSURE
AUTO 15OFF 40OFFAUTORET
1. POS/SIZE2. GRADATION3. DEFAULT4. RETURN
1. POS/SIZE : Select the region to apply DEFOG.2. GRADATION : You can set the level of DEFOG from 0 to 23. DEFAULT : The set point in PRIVACY TAB gets initialized.
DEFOG
0
RETPOSITION
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
BLCATWAUTO
SAVE&END
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
HSBLCATWAUTO
SAVE&END
POSITION
1. LEVEL2. AREA3. DEFAULT4. EXIT
BLC
MIDDLE
RET
1. SELECT2. DISPLAY3. BLACK MASK4. LEVEL5. MODE6. DEFAULT7. RETURN
1. SELECT : You can adjust 4 direction2. DISPLAY : You can select (ON, OFF)
3. BLACK MASK : The transmission range of light in HSBLC is shown in Black.
4. LEVEL : You can set the level of Black Mask from 0 to 100.
5. MODE : You can select. (ALL DAY, NIGHT)
6. DEFAULT : The set point in HSBLC TAB gets initialized.
HSBLC
AREA1ONON 20NIGHT
RET
POSITION
3. BACKLIGHT
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFMANUALAUTO
SAVE&END
1. BLUE2. RED3. RETURN
MANUAL WB
50 50RET
4. WHITE BAL
INDOOR : Select this when the color temperature is between 4500 K and 8500 KOUTDOOR : Select this when the color temperature is between 1800 K and 10500 K (sodium light inclusion)
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
1. D→N (AGC)2. D→N (DELAY)3. N→D (AGC)4. N→D (DELAY)5. RETURN
D&N AUTO
230 5 120 10RET
1. D→N (DELAY)2. N→D (DELAY)3. RETURN
D&N EXT
3 3RET
1. BURST2. IR SMART3. RETURN
B/W
OFFOFFRET
5. DAY&NIGHT
- IR PWM : Can adjust the display saturation as 0 to 100
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
1. 2DNR2. 3DNR3. RETURN
- 2DNR / 3DNR
NR
LOWMIDDLERET
6. NR
7. SPECIAL
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
CAM TITLE, D-EFFECT, MOTION, PRIVACY, LANGUAGE, DEFECT, RS485, RETURNcontrol can be selscted.
1. CAM TITLE2. D-EFFECT3. MOTION4. PRIVACY5. LANGUAGE6. DEFECT7. RS4858. RETURN
SPECIAL CAM TITLE
0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶ ()
/=&:~,.
CLR POS END
EAGLET
ON
OFFOFFENG
RET
1. CAM TITLE2. D-EFFECT3. MOTION4. PRIVACY5. LANGUAGE6. DEFECT7. RS4858. RETURN
SPECIAL
OFF
OFFOFFENG
RET
1. FREEZE2. MIRROR3. NEG.IMAGE4. RETURN
NEG.IMAGE
D-EFFECT
OFFOFFOFFRET
1. CAM TITLE
2. D-EFFECT
OFF MIRROR V-FLIP ROTATE
1. CAM TITLE2. D-EFFECT3. MOTION4. PRIVACY5. LANGUAGE6. DEFECT7. RS4858. RETURN
SPECIAL
OFF
ONOFFENG
RET
1. SELECT2. DISPLAY3. SENSITIVITY4. COLOR5. TRANS6. ALARAM7. DEFAULT8. RETURN
1. SELECT : Select the region to apply Privacy
2. DISPLAY : You can select (OFF / ON)3. SENSITIVITY : The available range of level is 0~1004. COLOR : You can change color of motion range in SELECT(green, blue, white, red)
5. TRANS : You can set the color lever of motion region selected in SELECT
6. ALARAM : Set the output system
7. DEFAULT : The set point in MOTION TAB gets initialized.
4
MOTION
AREA1ON 64GREEN1.00
RET
3. MOTION (Detects a moving odject)
1. SELECT2. DISPLAY3. COLOR4. TRANS5. DEFAULT6. RETURN
PRIVACY
AREA1COLORWHITE1.00
RET
1. CAM TITLE2. D-EFFECT3. MOTION4. PRIVACY5. LANGUAGE6. DEFECT7. RS4858. RETURN
SPECIAL
OFF
OFFONENG
RET
4. PRIVACY
1. SELECT : Select the region to apply Privacy
2. DISPLAY : You can apply 4 types (MOSAIC, INV., COLOR, OFF) in PRIVACY selected
3. SENSITIVITY : The available range of level is 0~1004. COLOR : You can change color of Privacy range in SELECT(green, blue, white, red)
5. TRANS : You can set the level of Privacy range in SELECT
6. DEFAULT : The set point in PRIVACY TAB gets initialized.
1. CAM TITLE2. D-EFFECT3. MOTION4. PRIVACY5. LANGUAGE6. DEFECT7. RS4858. RETURN
SPECIAL
OFF
OFFOFFENG
RET
1. LIVE DPC2. WHITE DPC3. BLACK DPC4. RETURN
DEFECT
ONONOFFRET
1. CAM TITLE2. D-EFFECT3. MOTION4. PRIVACY5. LANGUAGE6. DEFECT7. RS4858. RETURN
SPECIAL
OFF
OFFOFFENG
RET
1. CAM ID2. ID DISPLAY3. BAUDRATE4. RETURN
1. CAM ID : You can select camera ID from 0 to 255 when using remote control2. ID DISPLAY : You can move title by using UP, DOWN, LEFT, RIGHT button3. BAUDRATE : You can select 2400 / 4800 / 9600 / 19200 / 38400 bps.
RS485
0OFF38400RET
5. LANGUAGE
6. DEFECT
7. RS485
- DPC control modeYou can set the level point of DPC. (LIVE DPC / WHITE DPC / BLACK DPC)
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
1. LENS2. EXPOSURE3. BACKLIGHT4. WHITE BAL5. DAY&NIGHT6. NR7. SPECIAL8. ADJUST9. EXIT
MAIN MENU
MANUAL
OFFATWAUTO
SAVE&END
1. SHARPNESS2. MONITOR3. LSC4. VIDEO. OUT5. DATA VER6. OUTPUT SIZE7. RETURN
- SHARPNESS : Sharpness level control (LEVEL / START AGC / END AGC)- MONITOR : You can select (CRT / LCD)- LSC : When using wide angle, you can compensate darkness of corner on the screen- VIDEO. OUT : You can select (NTSC / PAL)- OUTPUT SIZE : 1080P / 720P
1. SAVE&END : Save the set of OSD
2. RESET : Factory initialize3. NOT SAVE : Do not save the set of OSD
ADJUST
AUTOLCDONNTSC0101011080PRET
8. ADJUST
9. EXIT
SHARPNESS, MONITOR, LSC, VIDEO. OUT, COMET, RETURN control can be selscted.