optrel e1100

No entry for smoke, particles and dust

Welders are put under a lot of stress during their work. The production of smoke, dust, vapour and gas is unavoidable during welding and other related work. These can pass via the larynx, wind pipes and bronchial system to the finest of bronchi-oles and alveoli which may result in a variety of respiratory diseases or even lung cancer. The breathing protection solutions from optrel’s expert range reliably protect against these dangers. A particle filtration system and a combined particle and gas filtration unit eliminate these dangers without restricting welder comfort. All optrel blower units are designed to be combined with the optrel e600 helmet shell. Thanks to a special inner mask to regulate airflow, the welder is permanently protected from harmful substances and at the same time benefits from a pleasant cooling effect. Maximum protection and comfort are guaranteed.

Automatically better weldingswiss made

optrel e1100optrel e1100 was developed especially for professional welders and offers ideal protection from the weld smoke, flying particles and dust which are released during welding and associated work. The filter used in this unit is a special, fine mesh filter for ideally filtering particles. optrel e1100 is supplied along with all helmets in the optrel e600 range.

optrel ag industriestrasse 2 9630 wattwil switzerland

p +41 71 987 42 00 f +41 71 987 42 99

info@optrel.com www.optrel.com

Features

Nominal protection factor TH2P classification (Europe) In accordance with BGR190, can be used for up to 20 times the workplace limit valueBlower unit Speed of airflow: at least 150 l/min, controlledMaterial Polyamide (PA-GF)Blower High-quality, ball bearing-mounted fan motorFusing Electronic fuseNoise level Max. 70 dB(A)Alarm signals Acoustic and visual alarms when battery

charge and airflow are low and filter is not fitted or is blocked

Battery (standard) Li-Ion, 4400 mAh, weight: 420 gBattery life Typically 11h (standard) / 16h (longlife)Charge time 7 hours for the standard batteryFilter 1 x TH3P type for TH2P systemHose Length: 1160 mm, weight: 185 gWeight 1205 g (blower including filter and belt)Dimensions (L x W x H): 249 x 213 x 87 mmGuarantee 2 years (not including battery)Certificates CE, AS/NZS, GOST-R

on off

Designation Article no.e1100 with 4240.003 e680 dark blue e1100 with 4260.001 e670 cosmic green e1100 with 4270.000 e650 black unpainted e1100 with 4280.000 e640 black unpainted

Optrel e1100 with e670

Technical data (blower)

Part No 4260.001 (Optrel e1100 + e670 cosmic green)

Type Powered Air Purifying Respirator (PAPR), battery powered Protection level: TH2 (EN12941), NPF 50 (EN529), APF 20 (BS4275), GW 20 (BGR190) TH3 (AS/NZS 1716)

Blower unit Flow rate: min. 150 l/min controlled Material: polyamid (PA-GF) Fan: high quality ball beared fan motor Fuse: electronic fuse Noise: max. 70dB Alarm: optical and audible alarm for low power and low air flow Dimensions (L x W x H): 249 x 213 x 87 mm Weight: 1205g / 42,505 oz (incl. filter and belt) Colour: blue / orange

Filter Quantity: 1 (Part No: 4088.000) Type TH3P R SL filter for TH2P system (EU) / TH3P system (AUS)

Hose Length: 1160 mm (elastic upto 1300mm with protective sleeve) (Part No: 4155.022) Diameter: 31 mm (inside) Weight: 185g / 6.526 oz (without protective sleeve) Colour: black

Type (Part No) Standard (4255.006) Long Life (4255.007) Type: Li-Ion rechargeable Li-Ion rechargeable Voltage / capacity: 11.1V / 4.8Ah 11.1V / 7.2Ah Charging cycles: > 1000 > 1000 Operating time*: minimum 6h, typical 11h minimum 9h, typical 16h Charging time: approx. 5h approx. 8h Weight: 420g / 14,815 oz 565g / 19,930 oz Colour: orange orange

*min. operating time is with dirty filter at room temperature

Charger Type: Microprocessor controlled, fully automatic (Part No. EU: 4255.001) Plug: EU-plug, UK-plug and US-plug (for Europe), AUS-plug (for AUS) (Part No. AUS: 4255.002) Primary voltage: 100 - 240 Volt @ 50 Hz/60Hz

Operating temperature -5°C to +55°C (without condensation)

Battery charging temp. +5°C to +25°C (without condensation)

Standards EN 12941:1998 TH2, AS/NZS 1716:2003 TH3

Notified body / Lic. No. CE 1024, 2824 SAI Global

EMV directive 89/336 /EEC, 92/31/EEC in succession 93/68/EEC

Scope of delivery Blower unit with hose, protective sleeve, TH3P R SL filter, battery, fabric belt, back support, charger, flow meter, user instructions.

Warranty (blower) 2 years from date of sales for manufacturing and material defects, no warranty for battery

Note! The Optrel e1100 respiratory system may NOT be used in environments where there is an immediate danger to health or life (IDLH), in atmospheres containing less than 17% (Europe) or 19% (Australia) oxygen or where the concentration of toxins is so high that a protection class in excess of TH2 (EU) / TH3 (AUS) is required. It is NOT evaluated as an ignition source in flammable or explosive atmospheres. The e1100 may NOT be worn as protection against gases or vapours. against gases or vapours.

Battery

Optrel e1100 with e670

Technical data (helmet)

Type description Welding helmet with true colour filter and colour fidelity, automatic darkening shade cartridge DIN 9-13 with 2 different modes, adjustable with a sliding switch: 1.: Automatic mode with manual finetuning 1 shade level. 2.: Manual selection of shade level 9-13 with potentiometer knob; grinding mode, sensitivity control knob; off-delay switch: dark to ligth (“fast”) or (“slow”)

Cartridge dimensions 90 x 110 x 7mm / 3,55 x 4,33 x 0,28" 50 x 100mm / 1,97 x 3,94" (Viewing area)

Power supply solar cells, 2pcs LI-batteries 3V exchangeable (CR2032)

Operating time batteries approx. 2500 houres (operating)

Sensors thre above the eyes variable detection angle with movable sensor slide

Light transmittance ultraviolet/infrared protection (maximum at any shade setting) visible range activated shade level DIN9 - 13 visible range not activated shade level 4

Switching time light to dark 175 μs (0,175 ms) at room temperature 120 μs (0,120 ms) at 55°C / 131°F dark to light position (“fast”) 0,1 - 0,35 s position (“slow”) > 0,35 s

Classification Optical class = 1 Scattered light = 1 Homogeneity = 1 Angular dependence = 2

Shape stability welding mask up to 220°C / 428°F front cover lens up to 137°C / 279°F

Protection for ADF reflection free front cover lens and inside cover lens

Mask material PA6.6

Mask colour Cosmic green

Operating temperature -10°C to + 70°C / 14°F to 158°F

Storage temperature -20°C to + 80°C / -4°F to 176°F

Weight Helmet cpl. 685 g / 24,163 oz Weight Cartridge cpl. 133g / 4,691 oz

Application ranges all electric arc welding processes Electrode Welding (Stick Welding, SMAW) / MIG / MAG (GMAW) / GMAW High melting

rate process / Flux Cored Wire Welding / TIG welding (GTAW) / Plasma Arc Welding / Micro Plasma Arc Welding / Plasmacutting / Grinding

prohibited for oxy gas and laser welding!

Scope of delivery Welding helmet and instruction manual

Standards EN 12941:1998 TH2, AS/NZS 1716:2003 TH3

Notified body CE 1024, 2824 SAI Global

Warranty (helmet) 2 years from date of sales for manufacturing and material defects (except batteries)

Subject to change without prior notice Status 2010-10-07 Optrel AG, Switzerland