OptoElectronic Instrumentation-Intrusion Sensor
Transcript of OptoElectronic Instrumentation-Intrusion Sensor
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 1/15
Click to edit Master subtitle style
4/13/12
BORDER SECURITY USINGFIBER OPTICS INTRUSION
SENSOR
SUBMITTED BY –
MITESH GOLCHHA(08BEI044)
VINEET JESWANI08BEI080
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 2/15
4/13/12
INTRODUCTION
A distributed FOS offers a low cost approach tomonitor the border for intruders.
It monitors long distances by analyzing the
RAYLEIGH Backscattered Signal.
A phase sensitive OTDR senses changes in theoptical phase of the back scattered light.
Intruder in the vicinity of the buried fiber producespressure and seismic waves which produces a
change in the optical path length and detected byOTDR. Monitorin can be extended to hundreds of
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 3/15
4/13/12FIG : Rayleigh backscattered signal with and withoutan intruder
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 4/15
4/13/12
INTRUSION DETECTION
Light pulses from semiconductor laser areinjected into the fiber and backscatteredlight is detected by a photo detector.
Laser with a narrow line width is necessaryfor OTDR.
Disturbances along the fiber are detectedby comparing the consecutive pulses.
Distance is proportional to the time delay.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 5/15
4/13/12
Ø – OTDR SYSTEM
FIG : Block diagram for -OTDR based intrusionφ
detection system.
EDFA = erbium doped fiber amplifierBPF = band pass filter
PBS = polarization beam splitterPD = photo detector
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 6/15
4/13/12
A highly coherent laser is used to introducepulses of light in the fiber.
The pulse period should be longer than time forthe optical pulse to propagate the length of thefiber and backscattered light to be completelydetected to avoid overlap of data.
Circulator is used for separation of the signals.
PBS is used for optimizing the probability of
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 7/15
4/13/12
INTRUSION LOCALIZATION
It is possible by knowing the difference inconsecutive pulses.
FIG : Plot showing two consecutive pulses of the backreflected signal, and the difference between them.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 8/15
4/13/12
If the speed of the light in the fiber is known,
time differences in the consecutive pulsescan be converted to distance, using relation-
d=(v*t)/2
½ factor is necessary because the pulse must
travel the fiber twice , i.e., to that location,and the Rayleigh backscattered light back tothe detector.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 9/15
4/13/12
DATA ACQUISITION AND
PROCESSING
The FPGA is programmed through LabVIEW tohandle data acquisition and processing.
The FPGA constantly acquires data over twochannels at 1.5 MS/sec and processes it inreal-time.
The data is filtered to remove noise and iscompared against a preprogrammed intrusioncriterion.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 10/15
4/13/12
The FPGA is programmed to maintain a 10second buffer of data.
When an intrusion criterion is met, intrusion
signal is triggered.
After creating the file, the software resets itself
and waits for another intrusion.
Buffer and recording times are fully adjustable.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 11/15
4/13/12
INTRUSION ANALYSIS
The intrusion
file created bythe software asshown in fig.
Contain bothraw andfiltered data
over twochannels.
FIG: An intrusion file triggeredby a single human intruder on
foot.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 12/15
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 13/15
4/13/12
For a single intruder in (a), individualfootsteps are clearly identifiable.
For the automobile intruder in (b),there iscontinuous disturbance while it is in the rangeof the buried fiber.
The amplitude of the disturbance isproportional to the distance from the fiber asthe car drives by.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 14/15
4/13/12
CONCLUSION
The scalability of real-time signalprocessing is limited by the amount of memory available on the FPGA unit.
This system allows for detection alongthe length of buried optical fiber while
localizing intrusion to a specific point.
The exact location of the intrusion can bedetected without the knowledge of intruder.
8/4/2019 OptoElectronic Instrumentation-Intrusion Sensor
http://slidepdf.com/reader/full/optoelectronic-instrumentation-intrusion-sensor 15/15
4/13/12
THANK YOU