Option Manual: LT70 DCS Laser Sight (Master)

Laser SightSafety, Operation, Maintenance

& Parts Manual

LS LT70DCS rev. A.00 - E.00 (LT70DCS & LT70Super)

Safety is our #1 concern! Read and understandall safety information and instructions before oper-ating, setting up or maintaining this machine.

February 2012

Form #1786

TOC

©2019

Printed in the United States of America, all rights reserved. No part of this man-ual may be reproduced in any form by any photographic, electronic, mechanicalor other means or used in any information storage and retrieval system withoutwritten permission from

Wood-Mizer 8180 West 10th Street

Indianapolis, Indiana 46214

CaliforniaProposition 65 Warning

WARNING: Breathing gas/diesel engine exhaust exposes you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Always start and operate the engine in a well-ventilated area.If in an enclosed area, vent the exhaust to the outside.Do not modify or tamper with the exhaust system.Do not idle the engine except as necessary.

For more information go to www.P65warnings.ca.gov.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection.

For more information go to www.P65Warnings.ca.gov/wood.

Table of Contents Section-Page

SECTION 1 LASER INSTALLATION 1-1

1.1 Laser Installation ....................................................................................1-11.2 Laser Activation (LT70DCS Only) ........................................................1-41.3 Laser Activation (LT70Super Only) ......................................................1-6

SECTION 2 OPERATION & ALIGNMENT 2-1

2.1 Laser Operation (LT70DCS Only).........................................................2-12.2 Laser Operation (LT70Super Only) .......................................................2-22.3 Laser Alignment .....................................................................................2-3

SECTION 3 REPLACEMENT PARTS 2-6

3.1 Laser Assembly ......................................................................................2-6Rev. E.00+

3.2 Laser Assembly ......................................................................................2-8Rev. A.00 - D.01

INDEX I

Table of Contents 60LS02doc032619 iii

Laser InstallationLaser Installation1

SECTION 1 LASER INSTALLATION

Before installing the laser option, be aware that the laser beam can not be seen in directsunlight. The laser option is best for indoor cutting applications.

1.1 Laser Installation

1. Locate the four square mounting holes on the saw head near the bottom of the drive-sideblade housing. Mount the laser/bracket assembly to the saw head using the four carriagehead bolts, flat washers and lock nuts. Rev. A.00 - D.01 Only: Place the star lock wash-ers between the laser bracket and the saw head to ensure proper grounding of the unit.

See Figure 1-1.

FIG. 1-1 REV. E.00+

FIG. 1-1 REV. A.00 - D.01

Laser/BracketAssembly

Carriage Head Bolts (4)

Flat Washers (4) Lock Nuts (4)600475-1

Laser/BracketAssembly

Carriage Head Bolts (4)

Star Lock Washers (4)

Flat Washers (4)

Lock Nuts (4)

600029-1B

1-1 60LS02doc032619 Laser Installation

Laser InstallationLaser Installation 1

2. Remove the drive belt guard.

3. Route the cable from the laser assembly as shown:

See Figure 1-2.

Route the laser cable under the saw head along the brace plate and secure thecable with the three provided wire clamps. Bolt the wire clamps to the brace platewith the three 1/4-20 x 1/2” hex head bolts, flat washers and self-locking nuts pro-vided.

Continue routing the laser cable as shown below and connect the laser cable plugto the laser harness plug.

Use the two provided wire ties to secure the laser cable to the saw head frame (andup/down motor wire harness for LT70DCS only).

Reinstall the drive belt guard.

FIG. 1-2 REV. E.00+ (LT70DCS SHOWN)

Wire Clamp (3)

Up/Down Motor(LT70DCS Only)

Laser Cable

600476BLaser Harness

Plug

Wire Tie

Up/Down MotorWire Harness

(LT70DCS Only)

Laser Installation 60LS02doc032619 1-2

Laser InstallationLaser Installation1

FIG. 1-2 REV. A.00 - D.01 (LT70DCS SHOWN)

Wire Clamp (3)

Laser Cable

600368B

Laser HarnessPlug

Wire Tie

Up/Down MotorWire Harness

(LT70DCS Only)Up/Down Motor(LT70DCS Only)


Laser InstallationLaser Activation (LT70DCS Only) 1

1.2 Laser Activation (LT70DCS Only)

The laser option needs to be activated in the control panel after installation. Use the fol-lowing steps to activate the laser option.

See Figure 1-3. Enter the User Configuration screen by pushing the UP button while inManual Mode. Select the System Options menu and push the CHECK button to enter.

FIG. 1-3

DC

SDC

Sistributedontrol

ystem

istributedontrol

ystem

DC

SDC

S

istributedontrol

ystem

istributedontrol

ystem

Auto-Down

212 40 120 0 0

21

A A

Auto-Up PatternManual

600369

Push UP button to enterConfiguration Menu

Push UP or DOWNarrow to select

Push CHECKbutton to accept

Auto-Mode Settings

DiagnosticsError Log

User Configuration

Engine TypeDashboard Settings

System Options

Regional Settings/Head Calibration


Laser InstallationLaser Activation (LT70DCS Only)1

Use the UP/DOWN arrows at the bottom to select the Laser Installed option. Use the sideUP/DOWN buttons to change the Laser Installed to Yes. Push the SAVE button to savethe changes and exit.

See Figure 1-4.

FIG. 1-4

DC

SDC

Sistributedontrol

ystem

istributedontrol

ystem

600370

System Options

Debarker Installed: YesLog Deck Installed: No

Laser Inactivity Timeout: 120 secHydraulic Offset: 82 %

Pull-Down Clamps: None

Laser Installed: Yes

Push SAVEbutton to save

changes and exit

Push UP/DOWNbutton to

change setting

Push UP or DOWNarrow to choose setting

Invert Joystick Controls: No


Laser InstallationLaser Activation (LT70Super Only) 1

1.3 Laser Activation (LT70Super Only)

The laser option does not need to be activated in the control panel after installation. Thelaser button is always available on the Main screen as shown below.

See Figure 1-5. Enter the Main screen to see the laser button.

FIG. 1-5

14.3 118 1542 0

n/minft/min

2

600419-17


Operation & AlignmentLaser Operation (LT70DCS Only)2

SECTION 2 OPERATION & ALIGNMENT

2.1 Laser Operation (LT70DCS Only)

When properly installed, the laser option will guide you in making cuts.

To turn on the laser, press the laser button on the control panel. The button LED will lightup.

To turn off the laser, press the laser button on the control panel. The button LED will goout.

NOTE: If the forward/reverse joystick is not used for 2 minutes, the laser will automati-cally turn off. Use of the forward/reverse joystick again will turn the laser back on.

See Figure 2-1.

FIG. 2-1

DC

SDC

Sistributedontrol

ystem

istributedontrol

ystem

Auto-Down

212 40 120 0 0

21

A A

Auto-Up PatternManual

600371

2-1 60LS02doc032619 Operation & Alignment

Operation & AlignmentLaser Operation (LT70Super Only) 2

2.2 Laser Operation (LT70Super Only)

When properly installed, the laser option will guide you in making cuts.

To turn on the laser, press the laser button on the Main screen. The laser icon will lightup.

To turn off the laser, press the laser button on the Main screen. The laser icon will go out.

NOTE: If the forward/reverse joystick is not used for 2 minutes, the laser will automati-cally turn off. Use of the forward/reverse joystick again will turn the laser back on.

See Figure 2-2.

FIG. 2-2

14.3 118 1542 0

n/minft/min

2

600419-17

Operation & Alignment 60LS02doc032619 2-2

Operation & AlignmentLaser Alignment2

2.3 Laser Alignment

1. Stationary sawmills should be setup on firm, level ground before proceeding with align-ment. Shim the feet so the weight of the sawmill is evenly supported.

Portable sawmills should also be setup on firm, level ground:

Adjust the two end outriggers on the main frame tube down just enough to lift weight fromthe trailer tire.

Adjust the two outer outriggers down just so they touch the ground but do not bearweight.

2. Make sure the sawmill is properly aligned (see the Alignment Section of your SawmillOperator’s Manual.)

3. Load a cant onto the bed of the sawmill.

4. Make a cut. Without raising the carriage head, return it to the front of the sawmill so thatblade remains level with the top of the cant and the carriage head is 1’ behind the front ofthe cant.

5. Align the laser. When the laser is properly aligned, approximately 10” of beam will showacross the front of the cant.

To adjust the laser vertically, loosen the assembly mounting fasteners. Move the entirelaser assembly up or down as necessary. Retighten the fasteners to secure the assemblyin position.

FIG. 2-2 REV. E.00+

Mounting Bolts (4)

600475-3


Operation & AlignmentLaser Alignment 2

See Figure 2-3. If the laser beam is adjusted too low, it will show against the side of thecant. But, in order to see a beam that is adjusted too high, it may be necessary to extendthe edge of the cant upward. To do this, fold pieces of paper in half and position them sothat the folds align with the outside edge of the cant as shown. Use a thumbtack tosecure the bottom half of the papers to the cant.

See Figure 2-4. To adjust the laser horizontally, loosen the laser pivot screws. Pivot thelaser diode side to side, or up and down, as necessary. Retighten the pivot screws tosecure the diode in place.

FIG. 2-2 REV. A.00 - D.01

FIG. 2-3

Mounting Bolts (4)

600029-3

Use tack to secure in place

Align fold of paper tooutside edge of cant

Operation & Alignment 60LS02doc032619 2-4

Operation & AlignmentLaser Alignment2

FIG. 2-4 REV. E.00+

FIG. 2-4 REV. A.00 - D.01

Pivot Screws

Laser Diode

600475-4

Pivot Screw

Laser Diode

Pivot Screw

600029-4


Replacement PartsLaser Assembly 2

SECTION 3 REPLACEMENT PARTS

3.1 Laser Assembly

Rev. E.00+

REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.

LASER KIT, COMPLETE FOR LT60/70 LS LT70DCS 1

Laser Assembly, 20 mW 638nm 90 Deg RED Line 073701 1

1 Mount Weldment, LT70 Laser 073863 1

2 Bolt, 5/16-18 x 1” Carriage Head F05006-9 4

3 Washer, #10 SAE Flat F05011-18 2

4 Washer, 5/16” SAE Flat F05011-17 4

1

2

4

5

3

7

6

8

9

10

11 12

13

14

600477

Replacement Parts 60LS02doc032619 2-6

Replacement PartsLaser Assembly2

5 Nut, 5/16-18 Hex Nylon Lock F05010-58 4

6 Laser, 20mW 638nm 90 Deg RED Line Z Laser 073700 1

7 Bracket, 18mm Swivel 074051 1

Tie Wrap, .100 x 4 Black F05089-6 2

8 Bolt, 10-24 x 3/4” Unslotted Hex Head F05004-167 2

9 Nut, 10-24 Hex Nylon Lock F05010-160 2

Bag Assembly, LT70 DCS Laser Parts 025935 1

10 Clamp, 1/4" Wire 9/32” Mounting Hole 025671 3

11 Tie Wrap, 1/4” x 6” F05089-1 2

12 Bolt, 1/4-20 x 1/2” Hex Head F05005-15 3

13 Washer, 1/4” SAE Flat F05011-11 3

14 Nut, 1/4-20 Hex Self-Locking F05010-9 3

Adapter, Lsr M12 4P Fml to Deutsch 2P Ml 078255 1

2-7 60LS02doc032619 Replacement Parts

Replacement PartsLaser Assembly 2

3.2 Laser Assembly

Rev. A.00 - D.01

REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.

LASER KIT, COMPLETE FOR LT70 DCS LS LT70DCS 1

Bracket Assembly, LT70 DCS Laser 053433 1

1 Mount Weldment, LT60/LT70 Laser 034863 1

2 Bolt, 5/16-18 x 1” Carriage Head F05006-9 4

3 Washer, 5/16” Exterior Star Lock F05011-33 4

4 Washer, 5/16” SAE Flat F05011-17 4

5 Nut, 5/16-18 Hex Nylon Lock F05010-58 4

1

2

34

5

6

7

8

9

8

9

12

13

10

11

14

15

16

600372

Replacement Parts 60LS02doc032619 2-8

Replacement PartsLaser Assembly2

6 Laser, 60deg Line w/Std Bkt & Connector 050367 1

Bracket, Laser Mount (Plastic) 045250 1

7 Power Supply, DCS Laser Sight 053432 1

8 Screw, #8-32 X 5/8” Socket Button Head Stainless Steel F05004-98 4

9 Nut, #8-32 Self Locking F05010-41 4

10 Decal, Revision 016187-LS 1

11 Overlayment, Revision Decal 016200 1

Bag Assembly, LT70 DCS Laser Parts 025935 1

12 Clamp, 1/4" Wire 9/32” Mounting Hole 025671 3

13 Tie Wrap, 1/4” x 6” F05089-1 2

14 Bolt, 1/4-20 x 1/2” Hex Head F05005-15 3

15 Washer, 1/4” SAE Flat F05011-11 3

16 Nut, 1/4-20 Hex Self-Locking F05010-9 3

2-9 60LS02doc032619 Replacement Parts

Index 60LS02doc032619 i

A

alignment 2-3

I

installation 1-1laser 1-1switch 1-4, 1-6

O

operation 2-1

R

replacement parts 2-6

INDEX

Option Manual: LT70 DCS Laser Sight (Master)

Documents

Transcript of Option Manual: LT70 DCS Laser Sight (Master)