OPERATION MANUAL - AIPHONE · 2018-08-07 · OPERATION MANUAL Thank you for selecting Aiphone for...

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S

WIDE ADJUST

ZOOM

Entrance station (modular type) Guard station

Entrance station (all-in-one type)

GT SYSTEM

OPERATION MANUAL

Thank you for selecting Aiphone for your communication needs. Please read this manual carefully before installation, and keep this in a safe place for future reference.

Please note that images and illustrations depicted in this manual may differ from the actual product.

Entrance station (modular type)Entrance station (all-in-one type)

Guard station

- 2 -

PRECAUTIONS

Prohibited Do not dismantle unit Keep unit away from water Be sure to follow the instruction

WARNING(Negligence could result in death or serious injury.)

1. Do not dismantle or alter the unit. Fire or electric shock could result. 2. Do not put any metal and fl ammable material into the unit through the

openings. Fire, electric shock, or unit trouble could result. 3. Keep the unit away from water or any other liquid. Fire or electric

shock could result. 4. During an electrical storm, do not touch the unit. Electric shock could

result. 5. If there is any smoke, unusual odor, or abnormal sound, or if you drop

or damage the unit, turn off the system power breaker immediately. Fire or electric shock could result.

6. Do not use power supply with a voltage other than specifi ed. Fire or electric shock could result

7. Do not use the unit in/under following locations/conditions. If not observed, it may result in noises or malfunctions. • Where use of the unit is prohibited, such as in a hospital • Near an electric medical equipment (e.g. operating rooms, ICU, or

CCU)• Near automatic control equipment such as auto doors or fi re-alarm

boxes• In the area within 15cm from a cardiac pacemaker

CAUTION(Negligence could result in injury to people or damage to property.)

1. Do not put anything on or cover the unit with cloth, etc. Fire or unit trouble could result.

2. Do not apply high pressure on the screen. If fractured, injury could result.

3. If the LCD is punctured, do not touch the liquid crystal inside. Infl ammation could result. If contact should occur, fl ush or rinse area with water thoroughly and consult your doctor.

4. Be sure to perform a call test with the handset on the hook. If you operate the hook switch with the handset on your ear, a sudden call etc. may arrive causing damage to your ear.

5. Do not place your ear near the speaker during use. An unexpected loud sound could cause hearing damage.

6. When cleaning the wall with a high-pressure water sprayer, be careful not to spray on the entrance station. If not observed, it may result in fi re or electric shock.

General Precautions1. Keep the unit more than 1 m (3.3') away from radio or TV set.2. Keep more than 20 cm (7-7/8") away from other radio equipment, for

example fl oor heating controller, wireless router or cordless telephone, etc. It may cause unwanted noise and video distortion.

3. Talk within 30 cm (12'') from this unit. If you are too far away, it may be diffi cult to hear audio.

4. When installing and using this unit, protect subject's privacy, portrait rights, etc. on your own responsibility.

5. As to other manufacturer's devices (such as sensor, detectors, door releases) used with this system, comply with the Specifi cations and Warranty conditions that the manufacturers or venders present.

6. Avoid using this unit in places under direct sunlight. If it is unavoidable, block out light during use.

7. When putting a hearing aid into T-mode and approaching the unit, the intercom system may be affected by radio frequency interference etc., depending on the installation environment.

8. Please receive and retain all confi guration data from the supplier. If you lose the confi guration data, there are cases where maintenance and after-sales service calls may incur additional setup fees.

9. The area to be monitored by the sensor should be free of obstacles such as ornamental plants.

Notice• We will under no conditions be liable for any damages or losses resulting

from this product's contents or specifi cations.• We will under no conditions be liable for damage occurring due to the

inability to communicate due to malfunctions, problems, or operational errors in this product.

• The unit is inoperative during power failure.• This system is not intended for life support or crime prevention. It is just a

supplementary means of conveying information. Aiphone will under no conditions be liable for loss of life or property which occurs while the system is being operated.

• In areas where broadcasting station antennas are close by, this system may be affected by radio frequency interference.

• Please note the LCD panel, though manufactured with very high precision techniques, inevitably will have a very small portion of its image elements always lit or not lit at all. This is not considered a unit malfunction.

• The unit may get slightly warm, but this is not a malfunction.• During communication, if you speak before the other person has fi nished

talking, your voice may not come through clearly. Conversation will proceed smoothly if you speak when the other person has fi nished talking.

• The entrance station is intended to be mounted on a wall only. It cannot be used on a desktop.

• Available functions and services are limited according to the specifi cations of the installed system.

• If you speak in a fi xed tone, the noise-cut function may judge it to be a noise and cut the transmission, but this is not a malfunction.

• Using a mobile phone or professional-use radio equipment such as walkie-talkie close to the system may cause a malfunction.

• Warm-color lighting shining on the camera may change the tint of the image on the screen.

• The outline of video images displayed may differ from that of the actual person(s) or background, but this is not a malfunction.

• When the unit’s screen is illuminated with strong light, the image looks white or silhouetted. But this is not a unit trouble.

• When outside temperature lowers sharply after rainfall, etc., the inside of the camera may fog up slightly, causing a blurry images, but this is not a malfunction. Normal operation will be restored when moisture evaporates.

• When using a fl uorescent light that shines around the camera, the screen colors may variously change (color rolling), but it is not a malfunction.

• If the entrance station freezes during winter time, the picture may become diffi cult to see or the buttons of the entrance station may not operate.

- 3 -

PRECAUTIONS ........................................................... 2

READ THIS BEFORE USING THE STATIONS

1 SYSTEM CONFIGURATION ........................................ 4

2 NOTES ABOUT USING THIS MANUAL .................... 5

ENTRANCE STATION

1 PART NAMES AND FUNCTIONS ............................... 61-1 Entrance station (modular type) ................................. 61-2 Entrance station (all-in-one type) ............................... 71-3 Indicators .................................................................... 8

2 OPERATIONS ................................................................. 92-1 Calling a resident/tenant or guard station .................. 9

Calling with the call switch module....................... 9Calling with the name scrolling module ................ 9Calling with the 10 key module ........................... 10Calling with the all-in-one type entrance station (GT-DMB-LVN/GT-DMB-N) .............................. 12

2-2 Door release ............................................................. 162-3 Other ........................................................................ 16

GUARD STATION

1 PART NAMES AND FUNCTIONS ............................. 171-1 Operation panel ........................................................ 171-2 Indicators .................................................................. 181-3 LCD (display) .......................................................... 191-4 Button operations ..................................................... 20

2 RECEIVING A CALL ................................................... 222-1 Receiving a call ........................................................ 22

3 CALLING (from a tenant building) ......................... 233-1 How to search for a unit to call

(from a tenant building) ........................................... 233-2 Calling a unit (residential/tenant station)

or guard station ........................................................ 243-3 Calling an entrance station ....................................... 29

4 CALLING (from a main building) ............................ 314-1 How to select a unit to call

(from a main building) ............................................. 314-2 Calling a room (residential/tenant station)

or guard station ........................................................ 324-3 Calling an entrance station ....................................... 37

5 OPERATIONS DURING COMMUNICATION .......... 395-1 Transferring a call .................................................... 395-2 Door release ............................................................. 395-3 Operating an optional device ................................... 405-4 Viewing and adjusting video at an entrance

station ....................................................................... 41

6 MONITORING ............................................................... 43

7 OTHER OPERATIONS ................................................ 457-1 Checking for missed calls and calling back ............. 457-2 Receiving an emergency call ................................... 46

8 SETTING........................................................................ 488-1 Adjusting display brightness and volumes ............... 488-2 Switching to reception mode ................................... 508-3 Switching to program mode ..................................... 51

9 UPDATING RESIDENT INFORMATION .................. 52

FOR PROPER USE OF THIS STATION

1 TECHNICAL PRECAUTIONS .................................... 53

2 SPECIFICATIONS ........................................................ 54

3 SOFTWARE LICENSE ................................................ 56

4 REGULATIONS ............................................................ 57

5 WARRANTY .................................................................. 58

Table of Contents

- 4 -

Example : A system (site) consisting of 1 main and 3 tenant buildings

The GT system consists of up to 8 main buildings and 24 tenant buildings.

Main building: A control section that functions as a main entrance, guard station, security center, administration offi ce, etc. A main building includes no residential/tenant stations. You can call up all of the residential/tenant stations and guard stations from an entrance station or guard station in the same system (site).* A station that is not programmed cannot be called.* Modular type entrance stations cannot be installed in a main building. Only all-in-one type can be used.

Tenant building: A section of collective housing. A tenant building includes residential/tenant stations, entrance stations and guard stations. You can call up all of the residential/tenant stations and guard stations from an entrance station in the same tenant building. However, you cannot call stations in another tenant building.

2B

A

C 3E

D

F

5K

J

L

8U

T

V

4H

G I 6N

M

O

1

0

9YX

W

Z

7RQ

P

S

Tenant buildingTenant building

Tenant building

Main building (administration offi ce)

Residential/tenant stations

Entrance station (all-in-one type only)


Entrance station (modular type)

Guard station

Guard station

GT-2C-L/GT-2C(GT-2H-L/GT-2H)

GT-1A GT-1DGT-1C7-L/GT-1C7

GT-1M3-L/GT-1M3

GT-DMB-LVN/GT-DMB-N

GT-DMB-LVN/GT-DMB-N

GT-MKB-N

GT-MKB-N


1 SYSTEM CONFIGURATION

- 5 -

Coverage of calling, communication and monitoringThe following table shows the coverage of calling, communication, and monitoring from a tenant building and a main building.

NOTE: Performance depends on the settings. If you cannot call even when ✓ is indicated, its setting is not confi gured.

Incoming callSame tenant building Other tenant buildings Same main

buildingOther main buildings

Entrance st.

Guard st.

Residential/tenant st.

Entrance st.

Guard st.


Entrance st.

Guard st.

Entrance st.

Guard st.

Tenant building

Entrance st. Calling/communication - ✓ ✓ - - - - - - -

Guard st. Calling/communication ✓ ✓ ✓ - - - ✓ ✓ ✓ ✓

Monitoring ✓ - - - - - - - - -

Main building

Entrance st. Calling/communication - ✓ ✓ - ✓ ✓ - ✓ - ✓

Guard st. Calling/communication ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

Monitoring ✓ - - ✓ - - ✓ - ✓ -

✓ : Possible — : Impossible

About the term "building" and "section": The term "section" is used on the setting screens of entrance stations and guard stations instead of "building". "Section" and "building" have the same meaning in this manual.

Out

goin

g ca

ll

This manual describes how to use the entrance stations and guard stations. The use of them differs depending on the building/section (main or tenant) where they belong. This manual uses the following icons to separate descriptions for the main and tenant buildings.

Icon Meaning

Main building/section

Tenant building/section

BUILDING #

01

UNIT #

1

CALLING METHOD

NAME / # SEARCHSECT LIST+UNIT #UNIT NUMBERSECT # + UNIT #

Setting screen of guard station

Standby screen of guard station

e.g. e.g.


2 NOTES ABOUT USING THIS MANUAL

- 6 -

2BA C

3ED F

5KJ L

8UT V

4HG I

6N

M O

1

0

9YX

W

Z

7RQ

P S

Camera module GT-VB

Name scrolling module GT-NSB

10 key module GT-10K

Call switch moduleGT-SW

Back search button (or move the cursor to the left)

Cancel button (or back)

Forward search button (or move the cursor to the right)

Call button (or set and move forward)

Display

10-key (0 to 9, , #)

Directory card

Call button

Audio module

GT-DB-VN (VIGIK and NFC capable)

GT-DB-V (VIGIK capable)

GT-DB

Camera

Microphone

IN USE LED (orange)

Call indicator (orange)

Talk indicator (orange)

Door release indicator (green)

NFC reader

Speaker

Illuminator LED

ENTRANCE STATION

Entrance station (modular type)1-1

[Combination examples]

GT-DB(-V, -VN) + GT-DBP

GT-SW + GF-4P

GF-BP

GT-SW + GF-4P


GT-VB + GT-VP

Audio only, Direct select type (8 stations)

Audio only, 10 key type

Audio/video, Direct select type (8 stations)

Audio/video, Direct select typeAudio/video, 10 key type

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S

GT-DB(-V,-VN) + GT-DBP

GT-VB + GT-VP

GT-NSB +GT-NSP-L

GT-10K + GF-10KP

GT-SW + GF-4P


GT-VB + GT-VP

GT-NSB + GT-NSP-L

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S


GT-NSB +GT-NSP-LGT-10K +

GF-10KP

1 PART NAMES AND FUNCTIONS

- 7 -

ENTRANCE STATION

All-in-one entrance stationGT-DMB-N

(NFC capable)

All-in-one entrance stationGT-DMB-LVN

(VIGIK and NFC capable, Hearing aid compatible)

Each part and indicator are the same as GT-DMB-N except as shown below (VIGIK).

Camera Microphone

Illuminator LED

Display

IN USE LED (orange)

Back search button (or move cursor to the left)

Forward search button (or move cursor to the right)

Cancel button (or back)

Call button (or set and move forward)

Sensor (If the sensor detects an object, the display will be illuminated.)

Speaker

Call indicator (orange)

Door release indicator (green)

Talk indicator (orange)

10-key (0 to 9, , #)

VIGIK (available in France)

Entrance station (all-in-one type)1-2

NFC reader

- 8 -

ENTRANCE STATION

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S

Indication patterns

1 IN USE LED (orange)

2 Call indicator

3 Talk indicator

4 Door release indicator

5 Display

Standby Off Off Off Off W E L C O M E (*3)

System in use Lit Off Off Off I N U S E

Call Off Lit Off Off (*1)C A L L I N GS M I T H

(*3)

Communication Off Off Lit Off (*2)I N C O M M U N I C A T I O N

Releasing a door Off Off (*1) Off (*2) Lit D O O R O P E N

Monitoring Off Off Off Off W E L C O M E

Communication is on hold Lit Off Off Off O N H O L D

(*1): Lit when door release is activated during call.

(*2): Lit when door release is activated during communication.

(*3): The display differs depending on the settings.

5

1

4

1

2

2

3 4

3

Indicator

Status

Entrance station (modular type) Entrance station (all-in-one type)

Indicators1-3

- 9 -

ENTRANCE STATION

Calling a resident/tenant or guard station2-1

Calling with the call switch module

1 Press the call button for the unit to be called.

The call indicator will light up and you will hear a call tone. * Audio guidance will be heard depending on

the settings.

When the call is answeredCommunication starts and the talk indicator lights up. * Audio guidance will be heard depending on the settings.

When the door is releasedThe door release indicator lights up. * Audio guidance will be heard depending on the settings.

Calling with the name scrolling module

■ Searching for a unit by scrolling the list

1 In standby mode, press and to display the target unit # and resident name.

2BA C

3ED F

5KJ L

4HG I

6NM O

1

101SMITH

* Depending on the settings, only the resident name may be displayed.

* The list is displayed in order of either unit # or resident name.

2 Press .

2BA C

3ED F

5KJ L

4HG I

6NM O

1


the settings.



: Main building/section : Tenant building/section

2 OPERATIONS

- 10 -

ENTRANCE STATION

Calling with the 10 key module

■ Searching for a unit by entering the unit #

1 In standby mode, enter the numbers using [0] to [9] on the 10-key to display the target unit # and resident name.

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S

101SMITH

2 When the target unit # and resident name is displayed, press .


the settings.

* If there is no relevant unit #, "NO ENTRY" is displayed.

NO ENTRY

* When the residential/tenant station that has been called is in use, the IN USE LED lights up to indicate that the residential/tenant station cannot be called. (In an expanded system, there may be a case that a residential/tenant station cannot be called even if the IN USE LED is off.)



■ Searching for a unit by entering resident name

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S

1 In standby mode, press on the 10-key.

2 When "ENTER A LETTER" is displayed, enter a letter using the 10-key to display the target unit # and resident name.

The number and resident name for the unit whose initial corresponds to the entered letter will be displayed.

(e.g.) Enter "S".

101SMITH

* Pressing or searches for the next unit # and resident name.


* When the unit # is set to not be displayed, a letter can be entered without pressing .

* If there is no relevant resident name, "NO ENTRY" is displayed.

NO ENTRY: S

NOTES:

• Pressing or for approximately 2 seconds will display resident names in succession.

• If both unit # 111 and 1111 exist, the resident name for unit 111 will be displayed when 1, 1, 1 is entered, and the resident name for unit 1111 will be displayed if 1 is entered one more time.

• Stations can be set to display in order by unit #. (The order starts with the lowest digit from 0 to 9 and then the order goes by letter.) In cases where unit # such as A101, A201, A901, A1001, and B101 exist, the order starts with the lowest digit and goes in the order A101, A201, A901, B101, A1001.

10-key

- 11 -

ENTRANCE STATION

3 When the target unit # or resident name is displayed, press .

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S

The call indicator will light up and you will hear a call tone. * Audio guidance will be heard depending on the

settings.



- 12 -

ENTRANCE STATION

Calling with the all-in-one type entrance station GT-DMB-LVN/GT-DMB-N

The following diagram shows the screen transitions starting from the standby screen. One of the standby screens shown below is preset to this

station. Find the standby screen of this station from A to E below and confi rm the transition from it, and refer to the designated page for the calling operation.

NOTE: If "NO ENTRY" is displayed on the screen, press .

WELCOME

Greeting message Picture

Call operation screen

Display OFF (black)

10-key/ / Turned on automatically

10-key/

A QUICK LIST

To the next page B or C

1. ENTER UNIT #

2. CALL

HOW TO CALL1. BUILDING LIST2. SELECT3. ENTER UNIT #4. CALL

HOW TO CALL1. ENTER BLDG. #2. SELECT3. ENTER UNIT #4. CALL

HOW TO CALL

NAME / # SEARCH UNIT NUMBER SECT LIST + UNIT#

SECT# + UNIT#

Standby screen

To the next page B To the next page C To the next page D To the next page E

101SMITH

UNIT LIST

CALL CANCEL

01CENTRAL TOWER

BUILDING LIST

SELECT CANCEL

* Depending on the setting, the screen turns on automatically when you get closer to this station.

10-key/

B C D E

10-key 10-key

10-key

101 SMITH102 AIPHONE103 DENTIST201 LAINE

INFORMATION

NUMBER ALPHA

BUILDING #

ALPHA

ENTER BUILDING #

ENTER CANCEL

UNIT #

ALPHA

ENTER UNIT #

CALL CANCEL

1. SELECT UNIT

2. CALL

HOW TO CALL

NUMBER ALPHA

( C is available in a tenant building/section only.)

- 13 -

ENTRANCE STATION

A Confi rming the target unit in the quick list

Unit # and resident names frequently called are preset to be displayed in the quick list.

* Up to 4 units can be displayed.

ALPHA

101 SMITH102 AIPHONE103 DENTIST201 LAINE

INFORMATION

NUMBER

1 In standby mode, press and to display the target unit, or 10-key to change the standby screen.

The "UNIT LIST" screen B or "ENTER UNIT #" screen C is displayed.

2 Follow the operating procedure of either B or C depending on the displayed screen.

* C is available in a tenant building/section only.

B Searching for a unit in the unit list

ALPHA

1. SELECT UNIT

2. CALL

HOW TO CALL

NUMBER

1 In standby mode, press and or 10-key to display the target unit # and resident name.

101SMITH

UNIT LIST

CALL CANCEL

The 10-key can be used to enter unit #, or by pressing , then the 10-key can be used to enter letters (resident name).


* The list is displayed in order of either unit # or resident name. * If you have entered a wrong number, press to return to

standby mode.

2 When the target unit is displayed, press .

The target unit is called. * Refer to "When the target unit is successfully called"

at the end of 2-1 for details.

C Entering unit #

NOTE: Entering unit # can only be performed on this screen. Entering resident name is not possible.

1. ENTER UNIT #

2. CALL

HOW TO CALL

When the target unit number is numerals only

1 In standby mode, enter numbers using [0] to [9] on the 10-key to display the target unit #.

* The 10-key can be used even after pressing or .

UNIT #

ALPHA

ENTER UNIT #

CALL CANCEL

* Depending on the system, only the resident name may be displayed.

* If you have entered a wrong number, press to return to standby mode.

2 When the target unit # is displayed, press .



When the target unit number is alphanumeric

1 In standby mode, press on the 10-key.

* The 10-key can be used even after pressing or .

UNIT #

NUMBER

ENTER UNIT #

CALL CANCEL

2 Enter letters using the 10-key to display the target unit #.

* Refer to the next page for how to enter letters.


The target unit is called.

* Refer to "When the target unit is successfully called" at the end of 2-1 for details.

Unit #

Resident name

or

or

- 14 -

ENTRANCE STATION

How to enter letters

(e.g.) Entering "CATHY"

1. To enter "C", press three times.

2. Press once. (*1)

3. To enter "A", press once.

4. To enter "T", press once.

5. To enter "H", press twice.

6. To enter "Y", press three times.

(*1): This step is needed for entering different letters with the same key sequentially.

To enter a special character

, : Press once.

- : Press twice.

. : Press three times.

/ : Press four times.

Space : Press fi ve times.

Æ : Press six times.

Ø : Press seven times.

Å : Press eight times.

* If you have entered a wrong letter, press to return to standby mode.

D Searching for a building in the building list and entering unit #

1.BUILDING LIST2.SELECT3.ENTER UNIT #4.CALL

HOW TO CALL

1 In standby mode, press and to display the target building number and name.

01CENTRAL TOWER

BUILDING LIST

SELECT CANCEL

2 When the target building is displayed, press .

3 Enter numbers or letters using the 10-key to display the target unit #.

* For entering numbers or letters, follow steps 1 and 2 of

C - "When the target unit number is numerals only"

or "When the target unit number is alphanumeric".

01CENTRAL TOWERUNIT #101

ENTER UNIT #

CALL ALPHA




- 15 -

ENTRANCE STATION

E Entering a building # and unit #

1.ENTER BLDG#2.SELECT3.ENTER UNIT #4.CALL

HOW TO CALL

1 In standby mode, enter numbers or letters using the 10-key to display the target building.




BUILDING #01

ALPHA

ENTER BUILDING #

ENTER CANCEL

2 When the target building number is displayed, press .

3 Enter numbers or letters using the 10-key to display the target unit #.




BUILDING # 01UNIT # 101

ENTER UNIT #

CALL ALPHA




When the target unit is successfully called

The call indicator will light up and you will hear a call tone. * Audio guidance will be heard depending on the settings.



NOTES: • If "DENIED" is displayed or returns to standby mode,

the entered unit #/resident name is not registered.• Enter the target unit # exactly. Otherwise, "DENIED" is

displayed or returns to standby mode.• If both unit # 111 and 1111 exist, the resident name for

unit 111 will be displayed when 1, 1, 1 is entered, and the resident name for unit 1111 will be displayed if 1 is entered one more time.

• Stations can be set to be displayed in order by unit #. (The order starts with the lowest digit from 0 to 9 and then the order goes by letter.) In cases where unit # such as A101, A201, A901, A1001, and B101 exist, the order starts with the lowest digit and goes in the order A101, A201, A901, B101, A1001.

- 16 -

ENTRANCE STATION

Door release2-2

Other2-3

■ Door release by using the access code

* The access code is preset by the system installer or administrator.

1 In standby mode, enter [#] and then the access code (4 to 6 digits) using [0] to [9] on the 10-key.

2BA C

3ED F

5KJ L

8UT V

4HG I

6NM O

1

0

9YX

W

Z

7RQ

P S

(e.g.)When the access code is "4567", enter "#", "4", "5", "6", "7".

The door is released.

• The door release indicator lights up.

• Audio guidance will be heard depending on the settings.

* If there is no relevant number, "DENIED" is displayed.* Door release is enabled even while the IN USE LED is lit.

■ Door release by an NFC-compliant IC card, etc.

A card incorporated with an NFC tag can be used to release a door. To use, the ID of the NFC tag must be registered as a door release code.

1 Pass an NFC-compliant IC card over the NFC reader.

* Put the card within 10 mm of the NFC reader. Otherwise, the

code may not be read correctly.

The door is released.

• The door release indicator lights up.

• Audio guidance will be heard depending on the settings.

* Door release is enabled even while the IN USE LED is lit.

NOTE: Do not overlap IC cards when passing them over the NFC reader. The code may not be read correctly.

[Modular type] [All-in-one-type]

NFC reader

[Modular type] [All-in-one-type]

* Calling from an entrance station is disabled while the IN USE LED is lit. Wait until the IN USE LED turns off.

NOTE: For a multi building system with lift control, if you unlock from a room and terminate call at the same time, the entrance station may not unlock properly.

- 17 -

WIDE ADJUST

ZOOM

Operation panel1-1

Handset Speaker

Color LCD monitor (Display)

Status LED (orange)

Indicates the current status of this station by lighting up or fl ashing on/off in orange (while initializing the system, being called, communicating, etc.).

Multi-function buttons

• LIGHT

• VIDEO CALL

• LIST

• SETTING

Option button

Door release ( ) button

ZOOM/WIDE button

ADJUST button

10-key (0 to 9, , #)

MONITOR button

TALK button

OFF button

Microphone

NFC reader

Reset button, USB terminal

GUARD STATION

1 PART NAMES AND FUNCTIONS

(up)

(right)(left)

(down)

- 18 -

GUARD STATION

Indication patterns

6 Status LED (orange)

Standby Off

Standby (Call tone volume: off)

Long interval flashing

(0.5 sec.) (5.5 sec.)

Standby (Reception mode: on)

Slow flashing

(0.5 sec.) (2.5 sec.)

This station is in use by another station (this station is inoperable)

Off

Being called by an entrance station Fast flashing

(0.5 sec.) (0.5 sec.)

Being called by a door station Normal flashing

(1 sec.) (1 sec.)

Being called by a door bell Fast flashing

(0.5 sec.) (1 sec.)

Monitoring an entrance station Lit

Communicating with an entrance station Lit

Calling another guard station or residential/tenant station (including in reception mode)

Fast flashing

(0.5 sec.) (0.5 sec.)

Sounding an emergency alarm Fast flashing

(0.5 sec.) (0.5 sec.)

A new list of missed calls from residential/tenant stations has arrived

Slow flashing

(0.5 sec.) (2.5 sec.)

Error indication Off (An error message is displayed.)

Communication is on hold Off

WIDE ADJUST

ZOOM

6

IndicatorStatus

Indicators1-2

- 19 -

GUARD STATION

ZOOM

WIDE

NAME SEARCH

EMERGENCY

NAME SEARCH

MISSED CALLS

NAME SEARCH

101102103201202

SMITHAIPHONEDENTISTLAINEMENIN

1 /8

The following are samples of typical screens and icons.

In standby mode* When nothing is displayed (black) on the screen, the screen below can be displayed by pressing

any key other than , 0-9, , or lifting the handset.

Information display

Displays the unit # or resident name of selected station, operation method, etc.

List page number

When the list of units or setting items consists of two or more pages, the current page number is shown here.

List of units

The list of units you searched for is shown here by their unit # and resident names. Nothing appears in the list when no corresponding unit is detected.

Status display iconsThe following icons are displayed here depending on the status of this station.

Icon The status when the icon appears

Appears when this station is in reception mode.

Appears while searching for a unit.

Appears while the number or letter entry screen is displayed.

Appears while receiving a call.

Appears when a record of missed calls is displayed.

Appears while in communication.

Appears while transferring.

Appears while this station is in communication with a residential/tenant station after transferring a call from an entrance station to the residential/tenant station.

Appears when a record of emergency calls is displayed.

Appears while monitoring.

Appears while a wide video at the entrance or a video at the door station is displayed.Appears while a zoom video at the entrance station is displayed.Appears when the setting screen is displayed.

LCD (display)1-3

NAME SEARCH screenThe screen for searching for a unit by its name.

NOTE: The above display example may differ from the actual one.

- 20 -

GUARD STATION

Button operations1-4

Multi-function buttons

Functions shown by icons here can be performed by pressing the buttons just below the icons. The icons vary depending on the status of this station.

When the same icon as the icon above a button is displayed, the button performs the function shown by the button name.

Turns on the light at an entrance station.

Starts communication with the preset entrance station, or displays video from a surveillance camera.

Displays the setting screen.

Displays the search item list.

(e.g.)

Pressing adjusts receive volume ( ).

(e.g.)

Pressing restores the previous screen ( ).

Icon Function

1Determines the choice.

Turns the entrance light on (when light is installed in common area).Adjusts brightness.

Turns off the emergency alarm.

2Calls the selected unit.

Transfers a call from entrance station to residential/tenant station.Adjusts call tone volume.

Turns off overlay.

Calls the preset entrance station directly.

Deletes the selected item.

Icons and their functionsIcons and their functions for each multi-function button are as follows.

1 4

2 3

Icon Function

3Changes the 10-key to the letter entry mode.

Changes the 10-key to the number entry mode.

Displays the search item list.

Adjusts receive volume.

4Restores the previous screen.

Displays the setting screen.

Cancels the choice.

■ Multi-function buttons and icons

The functions to be performed by the multi-function buttons are displayed by icons just above the buttons.

- 21 -

GUARD STATION

■ How to enter numbers and letters by using the 10-key (0 to 9, , #)

Use the 10-key in the number or letter entry mode.

The number and letter entry modes can be switched by pressing ( / ).

WIDE ADJUST

ZOOM

UNIT #

1

UNIT #

1

Number entry mode

Letter entry mode

Entered numbers are displayed.

How to enter letters

(e.g.) Entering "CATHY"

1. To enter "C", press three times.

2. Press WIDE

ZOOM

once. (*1)

3. To enter "A", press once.

4. To enter "T", press once.

5. To enter "H", press twice.

6. To enter "Y", press three times.

(*1): This step is needed for entering different letters with the same key sequentially.

To enter a special character

, : Press once.

- : Press twice.

. : Press three times.

/ : Press four times.

Space : Press fi ve times.

Æ : Press six times.

Ø : Press seven times.

Å : Press eight times.

* If you have entered a wrong letter, press to return to standby mode.

- 22 -

GUARD STATION

To answer a call

1 Press or lift handset.

WIDE ADJUST

ZOOM

or

2 Begin communication with the caller.

* Lift handset at any time for privacy.

* While communicating with the caller, unlock the door or use the other features by pressing the following buttons.

WIDE ADJUST

ZOOM

1011 PARKING GATE

To end communication

Press or hang up handset.

Communication ends automatically after 3 minutes.

* Communication with a residential/tenant station in hands-free mode ends automatically after 1 minute in hands-free mode.

WIDE ADJUST

ZOOM

101 DR.DOUIEB,PATRI

10 ENTRANCE1

1011 PARKING GATE

DOOR STATION

Receiving a call2-1

2 RECEIVING A CALL

: Main building/section : Tenant building/section

Caller

A call from a residential/tenant station or another guard station

A call from an entrance station with a camera

A call from an entrance station without a camera

A call from a door station

The unit # and station nameThe number and entrance name

The number and entrance name

The video at the entrance The video at the door station

The caller can be confi rmed on the display.

When receiving a call, the call tone sounds and the number and name of the caller (station) are displayed in the screen.

Answering a call

Door release (→ 5-2 )

Adjusting receive volume (→ 8-1 )

Adjusting call tone volume (→ 8-1 )

Operating an optional device (→ 5-3 )

Pan/tilt (→ 5-4 )

Zoom/wide (→ 5-4 )

Adjusting screen view (→ 5-4 )

Adjusting display brightness (→ 8-1 )

NOTE: When receiving a call from a door bell, nothing is displayed on the screen and answering is not possible.

- 23 -

GUARD STATION

3 CALLING (from a tenant building)

WIDE ADJUST

ZOOM

UNIT BY NUMBER

UNIT BY NUMBERUNIT BY NAMEGUARD STATIONENTRANCE

ZOOM

WIDE

NUMBER SEARCH

101102103104105

SMITHAIPHONEDENTISTYOKOIYABE

1 / 4

1

101102103201202


1 / 1

101 SMITH

NAME SEARCH

EMERGENCY

NAME SEARCH

MISSED CALLS

The following methods are available in standby mode to search for a unit (residential/tenant station) or guard station to call.

A Searching by number

B Searching by name

C Using the search item list

* When nothing is displayed (black) on the screen, press any key other than , 0-9, , or lift handset to enter standby mode.

* An entrance station can be searched for by using method C only.

Standby mode

How to search for a unit to call (from a tenant building) 3-1

A Searching by number (→ 3-2 )

B Searching by name (→ 3-2 )

C Using the search item list (→ 3-2 )

• Searching by number (UNIT BY NUMBER) (→ 3-2 )

• Searching by name (UNIT BY NAME) (→ 3-2 )

• Searching a guard station from the guard station list (GUARD STATION) (→ 3-2 )

• Searching an entrance station from the entrance station list (ENTRANCE) (→ 3-3 )

- 24 -

GUARD STATION

A Searching for a unit by number

1 In standby mode, enter numbers using [0] to [9] on the 10-key to display the target unit # and resident name.

NUMBER SEARCH

101102103104105


1 / 4

1

* The list is displayed in order of unit #.* This station is not displayed.

2 Select the target unit by pressing

WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUST

ZOOM

* Press WIDE

ZOOM

or WIDE

ZOOM

to turn the page of the list.

3 Press ( ), or lift handset.

When the call is answeredCommunication starts and " " is displayed.

4 To end communication, press or hang up handset.

NOTES:• Communication will end automatically after approximately 3

minutes. Communication with a residential/tenant station in hands-free mode ends automatically after 1 minute in hands-free mode.



Calling a unit (residential/tenant station) or guard station3-2

Entered number(s)

Unit # whose initial number matches the entered number are displayed in the list.

Incoming callSame tenant building Other tenant buildings Main building

Entrance st. Guard st.


Entrance st.

Guard st.


Entrance st. Guard st.

Tenant building

Guard st. Calling/communication

✓ ✓ ✓ - - - ✓ ✓

✓ : Possible — : Impossible

Coverage of calling from a guard station in a tenant building


Out

goin

g ca

ll

- 25 -

GUARD STATION

B Searching for a unit by name

1 In standby mode, press WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.The search screen is displayed.

2 Select the target unit by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

101102103201202


1 / 1

101 SMITH

* Press WIDE

ZOOM

or WIDE

ZOOM


* The list is displayed in order of either unit # or name.* This station is not displayed.







Selected unit # and resident name

Unit # and resident names are displayed in alphabetical or numerical order.* The arranging method differs depending on

the setting.

- 26 -

GUARD STATION

Searching for a unit by unit #

1 Select "UNIT BY NUMBER" by pressing WIDE

ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

UNIT BY NUMBER


2 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.The "NUMBER SEARCH" screen is displayed.

3 Enter numbers using [0] to [9] on the 10-key to display the target unit # and resident name.

NUMBER SEARCH

101102103104105


1 / 4

1


4 Select the target unit by pressing

WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

* Press WIDE

ZOOM

or WIDE

ZOOM





Entered unit #


C Searching for a unit by using the search item list

Press ( ).The search item list is displayed.

UNIT BY NUMBER


- 27 -

GUARD STATION

Searching for a unit by resident name

1 Select "UNIT BY NAME" by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

UNIT BY NAME


2 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.The "NAME SEARCH" screen is displayed.

3 Enter an alphabetical character using [0] to [9] on the 10-key to display the target resident name.

NAME SEARCH

102 AIPHONE1 /1

A

* The list is displayed in order of name.* This station is not displayed.


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

* Press WIDE

ZOOM

or WIDE

ZOOM





Entered character

The unit # and resident names whose initial letter matches the entered letter are displayed in the list.(e.g.) When "A" is entered, 301A, 1003ABC,

ABC, etc. are displayed in the list.* The arranging method differs depending on the

setting.

- 28 -

GUARD STATION

Searching for a guard station from the guard station list

1 Select "GUARD STATION" by pressing WIDE

ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

GUARD STATION


2 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.The guard station list is displayed.

3 Select the target guard station by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

001002003

GUARD1GUARD2GUARD3

1 / 1

001 GUARD1

* Press WIDE

ZOOM

or WIDE

ZOOM


* The list is displayed in order of either station number or name.* This station is not displayed.




Searching for an entrance station(→ 3-3 )





Guard station numbers and names are displayed in alphabetical or numerical order.* The arranging method differs depending on

the setting.

- 29 -

GUARD STATION

Calling an entrance station3-3

1 Press ( ).The search item list is displayed.

WIDE ADJUST

ZOOM

2 Select "ENTRANCE" by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

ENTRANCE


3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.The entrance station list is displayed.

4 Select the target entrance station by pressing

WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUST

ZOOM

00010002000300040005

ENTRANCE1ENTRANCE2ENTRANCE3ENTRANCE4ENTRANCE5

1 / 1

0001 ENTRANCE1

* Press WIDE

ZOOM

or WIDE

ZOOM


* The list is displayed in order of either station number or name.


Communication starts and " " is displayed.


NOTE: Communication will end automatically after approximately 3 minutes.

Direct calling an entrance station

(only when is displayed in standby

mode)

1 When is displayed, press ( ).

The preset entrance station is called, and then communication is enabled.

2 Talk hands-free or lift the handset.


Entrance station numbers and names are displayed in alphabetical or numerical order.* The arranging method differs depending on

the setting.

Selected entrance station number and name

- 30 -

GUARD STATION

Transferring video image taken by an entrance station camera or surveillance camera to a residential/tenant station


mode)

1 Press ( ).

2 Select a residential/tenant station by one of the following methods A - C .

A Press ( ) and then WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

to

select the target residential/tenant station.

B 1 Enter a number by using the 10-key to display the list of residential/tenant stations that include the number.

2 Press WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

to select the target

residential/tenant station.

3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.

C 1 Press and enter a letter by using the

10-key to display the list of residential/

tenant stations that include the letter.

2 Press WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM



3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.

3 Press ( ).

4 When the resident/tenant station answers and

accepts the visitor, press or hang up handset.

* Step 2 differs depending on the settings.

- 31 -

GUARD STATION

4 CALLING (from a main building)

WIDE ADJUST

ZOOM

1

2

34

BUILDING

BUILDINGGUARD STATIONENTRANCE

ZOOM

WIDE

ZOOM

WIDE

ZOOM

WIDE

NAME SEARCH

EMERGENCY

NAME SEARCH

MISSED CALLS

UNIT #

EMERGENCY

UNIT #

MISSED CALLS

BUILDING

EMERGENCY

BUILDING

MISSED CALLS

NUMBER SEARCH

101102103104105


1 / 4

1

The following methods are available in standby mode to select a room (residential/tenant station) or guard station to call.

A Searching by number

B 1 Searching for a unit in the list2 Entering unit # 3 Searching for a building in the list + entering unit #4 Entering a building # + unit #

C Using the search item list

* When nothing is displayed (black) on the screen, press any key other than , 0-9, , or lift handset to enter standby mode.

* To return to the standby screen, press .

* An entrance station can be searched for by using the method C only.

Standby mode

How to select a unit to call (from a main building) 4-1

A Searching by number (→ 4-2 )

B-1 Searching for a unit in the list (→ 4-2 )

B-2 Entering unit # (→ 4-2 )

B-3 Searching for a building in the list + unit # (→ 4-2 )

B-4 Entering a building # + unit # (→ 4-2 )

C Using the search item list (→ 4-2 )

• Searching for a building in the list + entering unit # or Entering a building # + unit # (→ 4-2 )

• Searching a guard station from the guard station list (GUARD STATION) (→ 4-2 )

• Searching an entrance station from the entrance station list (ENTRANCE) (→ 4-3 )

* Any of 1 to 4 are available by default.

- 32 -

GUARD STATION

Coverage of calling from a guard station in a main building


Incoming callTenant building Same main building Other main buildings

Entrance st.

Guard st.


Entrance st. Guard st. Entrance st. Guard st.

Main building

Guard st. Calling/communication

✓ ✓ ✓ ✓ ✓ ✓ ✓

✓ : Possible

Out

goin

g ca

ll

A Searching for a unit by number

1 In standby mode, enter numbers using [0] to [9] on the 10-key to display the target unit # and name.

NUMBER SEARCH

101102103104105


1 / 4

1



ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUST

ZOOM

* Press WIDE

ZOOM

or WIDE

ZOOM









Calling a room (residential/tenant station) or guard station4-2

Entered number(s)


- 33 -

GUARD STATION

B-1 Searching for a unit in the list


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.The unit list is displayed.

2 Select the target unit, by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

101102103201202


1 / 1

101 SMITH

* Press WIDE

ZOOM

or WIDE

ZOOM


* The list is displayed in order of either unit # or name.* This station is not displayed.


When the call is answeredCommunication starts and " " is displayed. * Audio guidance will be heard depending on the settings.


NOTE: Communication will end automatically after approximately 3 minutes. Communication with a residential/tenant station in hands-free mode ends automatically after 1 minute in hands-free mode.

B-2 Entering unit #


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

."UNIT #" screen is displayed.

2 [When the target unit number is numerals only] Enter the unit # using [0] to [9] on the 10-key.

[When the target unit number is alphanumeric]

1 Press ( ).

2 Enter the resident name using [0] to [9] on the 10-key.

* How to enter letters (→P. 21).

UNIT #

10








Selected unit # and name

Unit # and names are displayed in alphabetical or numerical order.* The arranging method differs depending on

the setting.

Entered number is displayed.

- 34 -

GUARD STATION

B-3 Searching for a building in the list + entering unit #


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.The building list is displayed.

2 Select the target building by pressing WIDE

ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

0102030405

CENTRAL TOWEREAST TOWERWEST TOWERNORTH TOWERSOUTH TOWER

1 / 1

01 CENTRAL TOWER

* Press WIDE

ZOOM

or WIDE

ZOOM


* The list is displayed in order of either building number or name.

3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

."UNIT #" is displayed.



1 Press ( ).



UNIT #

1

01 CENTRAL TOWER




B-4 Entering a building # + unit #


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

."BUILDING #" screen is displayed.

2 [When the target building number is numerals only] Enter the building number using [0] to [9] on the 10-key.

[When the target building number is alphanumeric]

1 Press ( ).

2 Enter the building name using [0] to [9] on the 10-key.


BUILDING #

0

3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

."UNIT #" is displayed.



1 Press ( ).



BUILDING #

01

UNIT #

1




Selected building number and name

Building numbers and names are displayed in alphabetical or numerical order.* The arranging method differs depending on

the setting.

Selected building is displayed.




- 35 -

GUARD STATION

C Searching for a unit by using the search item list

Searching for a building in the list + entering unit #


2 Select "BUILDING" by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

BUILDING


3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM


4 Follow steps 2 to 6 of B-3 .

Entering a building # + unit #


2 Select "BUILDING" by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

BUILDING


3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

."BUILDING #" screen is displayed.

4 Follow steps 2 to 6 of B-4 .





- 36 -

GUARD STATION

Searching for a guard station from the guard station list


2 Select "GUARD STATION" by pressing WIDE

ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

GUARD STATION


3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM



ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

0102030405


1 / 1

01 CENTRAL TOWER

* Press WIDE

ZOOM

or WIDE

ZOOM



5 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.The guard station list is displayed.

6 Select the target guard station by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

001002003

GUARD1GUARD2GUARD3

1 / 1

01 CENTRAL TOWER001 GUARD1

* Press WIDE

ZOOM

or WIDE

ZOOM


* The list is displayed in order of either station number or name.* This station is not displayed.










the setting.

Guard station numbers and names are displayed in alphabetical or numerical order.* The arranging method differs depending on

the setting.

- 37 -

GUARD STATION

Calling an entrance station4-3


WIDE ADJUST

ZOOM


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

ENTRANCE


3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM



ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

0102030405


1 / 1

01 CENTRAL TOWER

* Press WIDE

ZOOM

or WIDE

ZOOM



5 Press ( ) or WIDE

ZOOM

WIDE

ZOOM


6 Select the target entrance station.

WIDE ADJUS

ZOOM

00010002000300040005


1 / 1

0001 ENTRANCE1

* Press WIDE

ZOOM

or WIDE

ZOOM




When the call is answeredCommunication starts and " " is displayed. * Audio guidance will be heard depending on the settings.


NOTE: Communication will end automatically after approximately 3 minutes.


the setting.




the setting.

- 38 -

GUARD STATION

Direct calling an entrance station


mode)

1 When is displayed, press ( ).

The preset entrance station is called, and then communication is enabled.

2 Talk hands-free or lift the handset.


Transferring video image taken by an entrance station camera or surveillance camera to a residential/tenant station


mode)

1 Press ( ).

2 Select a residential/tenant station by one of the following methods A - C .

A Press ( ) and then WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

to

select the target residential/tenant station.

B 1 Enter a number by using the 10-key to display the list of residential/tenant stations that include the number.

2 Press WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM



3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.

C 1 Press and enter a letter by using the

10-key to display the list of residential/

tenant stations that include the letter.

2 Press WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM



3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.

3 Press ( ).

4 When the resident/tenant station answers and

accepts the visitor, press or hang up handset.


- 39 -

GUARD STATION

5 OPERATIONS DURING COMMUNICATION

A call from an entrance station can be transferred to a residential/tenant station via a guard station

1 After the guard station is called from an entrance

station, press or lift handset to answer the call.

WIDE

ZOOM1011PARKING GATE

2 Press ( ) or enter the unit # by using [0] to [9] on the 10-key.The list of residential/tenant stations is displayed.

3 Select the target residential/tenant station, then

press ( ).

The call is transferred to the residential/tenant station.

* "ON HOLD" is displayed on the entrance station and no sound is heard at the entrance station.

4 When the residential/tenant station answers and

accepts the visitor, press or hang up handset to establish communication between the entrance station and the residential/tenant station.

* When there is no answer from the residential/tenant station,

hang up handset and pick it up again, or press and

then to communicate with the entrance station.


Reference: Reception mode (→ 8-2 )When there is a call from an entrance station to a residential/tenant station, it is fi rst transferred to the guard station, so a call tone sounds and the video at the entrance station is displayed on the guard station.

1 While receiving a call or communicating with an

entrance station, press .

WIDE ADJUST

ZOOM

Door release is activated at the entrance station.

* Audio guidance will be heard depending on the settings.

NOTES:• For an all-in-one type entrance station:

The door lock is released for the preset time. If the preset release time is “0”, it can be released while the button is pressed and held.

For a modular type entrance station: If the VR1 dial (inside the cover) is set to “M (Momentary)”, it can be released while the button is pressed and held.

• Depending on the electric door release system that you use, door release may be active only while the door release button is pressed.

CAUTION: Be sure to confi rm the visitor securely before releasing the door if the entrance station has no camera.

The number and name of calling entrance station

Door releaseTransferring a call 5-25-1

- 40 -

GUARD STATION

You can operate an optional device such as a light on this station.

1 Press .

WIDE ADJUST

ZOOM

The optional device turns on.

NOTES:• A signal is sent to the device installed in the site. Please refer to

the specifi cations of the device.• If no optional device is installed, nothing happens when the

button is pressed.

Operating an optional device5-3

- 41 -

GUARD STATION

Viewing and adjusting video at an entrance station5-4

You can view video at the target station when receiving a call from or communicating with an entrance station with a camera, or monitoring it. The video can be adjusted as desired by using the following functions.

* These functions are not available for a door station.

Switching Zoom/WideThe display mode can be switched between zoom and wide by each

press of WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUST

ZOOM

NOTES:• The preset position of zoom image depends on the setting.• When the display mode switches from wide to zoom, the zoom

image is displayed at the preset position.• Depending on the properties of the camera, the wide image may

appear more distorted than the zoom image but this is not a malfunction.

• The image range of the zoom mode and wide mode differs. The edge of wide image will not be displayed with the zoom mode.

Pan & Tilt

When a zoom image is displayed, pressing WIDE

ZOOM

, WIDE

ZOOM

, WIDE

ZOOM

,

WIDE

ZOOM

WIDE

ZOOM

, moves the image as shown below.

WIDE ADJUST

ZOOM

NOTES: • At night, the object image may be blurred and less-visible when

moving the image from right to left or up and down because illumination to the object is reduced. The same applies to a moving object.

• The pan & tilt function is not available for a video door station (JO-DV) .

Wide

Zoom

- 42 -

GUARD STATION

Adjusting screen viewIf the video on the screen is diffi cult to see, you can adjust the screen view.

1 Press ADJUST when the video is diffi cult to see.

WIDE ADJUST

ZOOM

The backlight or night sensitivity is automatically adjusted.

* The discrimination between day and night is performed automatically by this station.

* The adjustment result may vary depending on the setting.

To restore the screen view before adjustment

Press ADJUST again.The icon is cleared and the screen view before adjustment is restored.

NOTES:• Pressing ADJUST at night may make visitors' faces easier to see, but

may also make moving objects more diffi cult to see. • The screen view adjusting function is not available for a video

door station (JO-DV).

<Day> <Night>

[Before adjustment]

[After adjustment] [After adjustment]

[Before adjustment]

- 43 -

GUARD STATION

6 MONITORINGYou can monitor an entrance station or door station.

* When monitoring an entrance station or door station with a camera, you can view the video at the station and hear the sound.

* The monitoring function is not available for an entrance station or door station without a camera.

Monitoring from a tenant building

* For monitoring a door station, start from step 5.

1 In standby mode, press ( ).

WIDE ADJUST

ZOOM

The search item list is displayed.


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

ENTRANCE


3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM


4 Select the target entrance station by pressing

WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUST

ZOOM

00010002000300040005


1 / 1

0001 ENTRANCE1

* Press WIDE

ZOOM

or WIDE

ZOOM



5 Press .

The sound at the station is heard, and the video is displayed on the screen.

1011 PARKING GATE

* While monitoring, you can switch zoom/wide, pan & tilt, and adjust the screen view. (→ 5-4 )

6 [To communicate with the station]

Press or lift handset.

WIDE ADJUST

ZOOM

or

Communication with the station starts and " " is displayed.

* Until this step, the monitored stations cannot hear any sound from the guard station.

7 To end monitoring or communication,


NOTES:• Monitoring ends automatically after about 30 seconds.• Only entrance stations that can be selected by the guard station

can be monitored.• When no door station is installed, pressing has no

effect on the display.


the setting.


Selected station number and name

- 44 -

GUARD STATION

Monitoring from a main building

* For monitoring a door station, start from step 7.

1 In standby mode, press ( ).The search item list is displayed.

WIDE ADJUST

ZOOM


ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

ENTRANCE


3 Press ( ) or WIDE

ZOOM

WIDE

ZOOM


4 Select the target building.

WIDE ADJUS

ZOOM

0102030405


1 / 1

01 CENTRAL TOWER

* Press WIDE

ZOOM

or WIDE

ZOOM



5 Press ( ) or WIDE

ZOOM

WIDE

ZOOM


6 Select the target entrance station.

WIDE ADJUS

ZOOM

00010002000300040005


1 / 1

0001 ENTRANCE1

* Press WIDE

ZOOM

or WIDE

ZOOM



7 Press .

The sound at the station is heard, and the video is displayed on the screen.

1011 PARKING GATE

* While monitoring, you can switch zoom/wide, pan & tilt, and adjust the screen view. (→ 5-4 )

8 [To communicate with the station]

Press or lift handset.

WIDE ADJUST

ZOOM

or

Communication with the entrance station side starts and " " is displayed.

* Until this step, the monitored stations cannot hear any sound from the guard station.

9 To end monitoring or communication,


NOTES:• Monitoring ends automatically after about 30 seconds.• Only entrance stations that can be selected by the guard station

can be monitored.• When no door station is installed, pressing has no

effect on the display.


the setting.




the setting.

Selected station number and name

- 45 -

GUARD STATION

Checking for missed calls and calling back7-1

If this station fails to respond to a call from a residential/tenant station, "MISSED CALLS" fl ashes continuously on the display in standby mode, and the status LED on the unit fl ashes. Check the missed calls and call back if necessary.

ZOOM

1 To check for missed calls, press WIDE

ZOOM

in standby mode.A record of missed calls is displayed.

WIDE ADJUST

ZOOM

101102103201202


1 / 1

101 SMITH

MISSED CALLS

2 To call back, select the target unit by pressing

WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUST

ZOOM

101102103201202


1 / 1

102 AIPHONE

MISSED CALLS

* Press WIDE

ZOOM

or WIDE

ZOOM


* Depending on the settings, only the unit # may be displayed.



4 To end communication,

press or hang up handset.

NOTES:• The guard station can hold up to 20 missed calls.• A record of answered calls is not kept.• While a record of missed calls are displayed, this station cannot

enter program mode.

Selected unit # and name* On a guard station in a main section, the

building #, building name, and unit # of the selected unit are displayed.

When there are two or more missed calls, they are listed in reverse chronological order.* On a guard station in a main section, building

#, building names, and unit # are displayed.

7 OTHER OPERATIONS

ZOOM

WIDE

NAME SEARCH

EMERGENCY

NAME SEARCH

MISSED CALLS

Flashes.

Flashes.

- 46 -

GUARD STATION

Receiving an emergency call7-2

When an emergency alarm switch is locked (or when a wire disconnection occurs), an alarm sounds and an "EMERGENCY" screen is displayed on this station. Check for the unit that sent the emergency call, and take the necessary action.

EMERGENCY101 SMITH

1 To stop the alarm sound, press ( ).

WIDE ADJU

ZOOM

EMERGENCY101 SMITH

101 SMITH1 / 1

The alarm stops and a record of emergency calls is displayed.* On a guard station in a main section, building #, building

names, and unit # are displayed. * When linked with multiple guard stations, stopping the alarm

on any guard station will stop the alarm of all the guard stations.

2 To communicate with the unit, press ( ),

or lift handset.

WIDE ADJU

ZOOM

EMERGENCY101 SMITH

101 SMITH1 / 1

* When there are two or more emergency calls, select one by

pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

, then press ( ),

or lift handset.

* Press WIDE

ZOOM

or WIDE

ZOOM


* The list is displayed in chronological order.



To delete an emergency call from the list.

Select the target call by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

,

then press ( ).

WIDE ADJUST

ZOOM

EMERGENCY101 SMITH

101201

SMITHLAINE

1 / 1

NOTE: While a record of emergency calls are displayed, this station cannot enter program mode.

The unit # and name of the unit that sent the emergency call* On a guard station in

a main section, the building #, building name, and unit # are displayed.

- 47 -

GUARD STATION

To display a record of emergency calls

ZOOM

WIDE

NAME SEARCH

EMERGENCY

NAME SEARCH

MISSED CALLS

1 Press WIDE

ZOOM

In standby mode.A record of emergency calls is displayed.

To call a room that sent the emergency call

Select the target record by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

, and

then press ( ), or lift handset.

NOTE: The emergency alarm keeps fl ashing until the target record is deleted from the list. To delete it, select it on the list and

then press ( ).

The residential/tenant station keeps sounding the alarm until the emergency alarm switch is restored at the room. In such case, the record of emergency calls cannot be deleted with the guard station. Unless the alarm is restored at the room, no call can be made from the guard station to the room. Please make sure the alarm is restored at the room.

NOTES:• If an emergency call is already active on this station and this

station is in communication, another guard station cannot interrupt. (An in-use tone will be heard from handset or speaker of the guard station.)

• The emergency alarm is given priority even when the system is in use. (Alarms can be activated at the same time for up to 5 units. This excludes GT-2C-L and GT-2C.)

• Emergency calls can be made while the system is in use.• With the GT-2C-L and GT-2C, it is possible to transfer to a guard

station even when there is a security alarm, depending on the settings.

• Even when the call tone volume is set to mute on the guard station, an alarm goes off at the maximum volume.

Flashes when there is one or more unchecked emergency calls.

- 48 -

GUARD STATION

8 SETTING

Adjusting display brightness and volumes8-1

Adjusting brightness of the display

1 In standby mode, press .

WIDE ADJUST

ZOOM

The SETTINGS screen is displayed.

2 Select "BRIGHTNESS" by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS

3 Adjust the brightness by pressing WIDE

ZOOM

or WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS

Adjustment can be made in 10 levels.

To return to the previous screen

Press ( ).

To adjust brightness of the display while being called or in communication

1 While being called or in communication,

press .

2 Press ( ).

3 Adjust the brightness by pressing WIDE

ZOOM

or WIDE

ZOOM

.

Adjusting the call tone volumeYou can adjust the call tone volume at this station.

1 In standby mode, press .The SETTINGS screen is displayed.

2 Select "TONE VOLUME" by pressing WIDE

ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS

3 Adjust the volume by pressing WIDE

ZOOM

or WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS

Adjustment can be made in 4 levels. ("Mute" is available.)* If set to "mute”, the status LED will fl ash with

long intervals. (→ 1-2 )


Press ( ).

To adjust the call tone volume while being called or in communication


press .

2 Press .


ZOOM

or WIDE

ZOOM

.

- 49 -

GUARD STATION

Adjusting the receive volumeYou can adjust the speaker volume of this station.


2 Select "RECEIVE VOLUME" by pressing WIDE

ZOOM

or

WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS


ZOOM

or WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS

Adjustment can be made in 3 levels.


Press ( ).

To adjust the receive volume while being called or in communication


press .

2 Press ( ).


ZOOM

or WIDE

ZOOM

.

- 50 -

GUARD STATION

* This section describes the reception mode and how to confi gure it. Refer to steps 2 to 3 of " 5-1 Transferring a call" for the operating procedure.

What is reception mode?

In reception mode, all of the calls from entrance stations to residential/tenant stations are fi rst transferred to guard stations. You can transfer the calls to residential/tenant stations after confi rming they are not unwanted calls to the target residents.

[Normal mode]

NOTES:• In a main building: Calls from an entrance station are transferred to all guard stations

in the building. The call tone sounds on all guard stations at the same time.

In a tenant building: Calls from an entrance station are transferred to all guard stations

in the tenant building that are linked to the corresponding residential/tenant station. The call tone sounds on all guard stations at the same time.

• A call to a residential/tenant station that is not linked to a guard station will result in a call to the residential/tenant station directly.

Switching this station between normal mode and reception mode


2 Select "ADVANCED SETTINGS"

by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS

3 Select "RECEPTION MODE"

by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

ADVANCED SETTINGS

RECEPTION MODE OFFPROGRAM MODE

4 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.

5 Change reception mode to "ON" or "OFF" by

pressing WIDE

ZOOM

or WIDE

ZOOM

.

WIDE ADJUS

ZOOM

ADVANCED SETTINGS


ON: Reception mode is active. OFF: Normal mode is active.

6 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.

* When this station is in reception mode, the status LED will fl ash slowly. (→ 1-2 )


Press ( ).

Switching to reception mode8-2

Residential/tenant station

Residential/tenant station

Entrance station

Call

Call Transfer

Entrance station

[Reception mode]

Guard station (this station)

Guard station (this station)

- 51 -

GUARD STATION

* This operation is for Administrators and Managers only

Entering a passcord is needed to switch this station into program mode. Ask the system installer for the passcord.

* A registered NFC-compliant IC card can be used instead of a passcord.

1 In standby mode, press (or pass an registered NFC-compliant IC card over the NFC reader).The SETTINGS screen is displayed.

2 Select "ADVANCED SETTINGS"

by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

SETTINGS

BRIGHTNESS

TONE VOLUME

RECEIVE VOLUME

ADVANCED SETTINGS

3 Select "PROGRAM MODE"

by pressing WIDE

ZOOM

or WIDE

ZOOM

WIDE

ZOOM

.

WIDE ADJUS

ZOOM

ADVANCED SETTINGS


4 Press ( ) or WIDE

ZOOM

WIDE

ZOOM

.The passcord entry screen is displayed.

5 Enter the passcord.

* Refer to the GT SYSTEM SETTING MANUAL/Standard & Expanded System for details about the settings.

NOTE: An NFC card can be used with either "Admin" or "Manager" authority. (→ GT SYSTEM SETTING MANUAL/Standard & Expanded System)

Switching to program mode8-3

- 52 -

GUARD STATION

9 UPDATING RESIDENT INFORMATIONRefer to the GT SYSTEM/SETTING MANUAL.

• For single building system (→ GT SYSTEM SETTING MANUAL/Standard & Expanded System)

• For multi building system (→ GT SYSTEM SETTING MANUAL/Multi Building System)

When using an Android device(→ GT SYSTEM SETTING MANUAL/Aiphone GT Setup Tool for Android)

Android is a trademark of Google Inc. in the United States and/or other countries.

- 53 -

[For guard station only]• The video image may distort when door release is activated. This

is not a station malfunction.• If a zoom/wide, pan/tilt, door release operation or brightness

adjustment is performed during communication with the entrance station, noise will be produced at the entrance station. This is not a malfunction.

[General]• If there is a system malfunction, contact a qualifi ed technician for

service.

• Cleaning: Clean the units with a soft cloth dampened with a neutral

household cleanser. Do not use any abrasive cleaner or cloth. CAUTION: Do not use chemicals such as thinner or benzine. In

addition, do not use a scrub brush, sandpaper, etc. Otherwise the unit surface could be damaged or discolored.

1 TECHNICAL PRECAUTIONS


- 54 -


2 SPECIFICATIONS

Entrance station (modular type)

Camera module (GT-VB)Power source Supplied from GT-VBCAmbient temperature - 10°C - +60°C (+14°F - +140°F)Material Self-extinguishing PC+ABS resin

Dimensions108 (W) x 93 (H) x 55 (D) mm4-1/4" (W) x 3-11/16" (H) x 2-3/16" (D)

Mass Approx. 130g (0.29 lbs.)

Camera module panel (GT-VP)Material Zinc die castColor Metallic beige

Dimensions110 (W) x 95 (H) x 8 (D) mm4-5/16" (W) x 3-3/4" (H) x 5/16" (D)


Audio module (GT-DB/GT-DB-V/GT-DB-VN)Power source Supplied from GT-BCAmbient temperature - 10°C - +60°C (+14°F - +140°F)Material Self-extinguishing ABS resin

Dimensions108 (W) x 93 (H) x 53.4 (D) mm4-1/4" (W) x 3-11/16" (H) x 2-1/8" (D)

MassGT-DB, GT-DB-V: Approx. 210g (0.47 lbs)GT-DB-VN: Approx. 220g (0.49 lbs)

Audio panel (GT-DBP)Material Zinc die castColor Metallic beige

Dimensions109.7 (W) x 94.9 (H) x 7.9 (D) mm4-5/16" (W) x 3-3/4" (H) x 5/16" (D)

Mass Approx. 95g (0.21 lbs)

Name scrolling module (GT-NSB)

Power sourceDC 24V supplied from a power supply unit (PS-2420 etc.)

Ambient temperature - 10°C - +60°C (+14°F - +140°F)Material Self-extinguishing ABS resin

Dimensions104.6 (W) x 88.3 (H) x 49.1 (D) mm4-1/8" (W) x 3-1/2" (H) x 1-15/16" (D)

Mass Approx. 140g (0.31 lbs)

Name scrolling module panel (GT-NSP-L)

MaterialPanel: Zinc die castWindow: PolycarbonateBottom: Chrome plated zinc die cast

Color Metallic beige

Dimensions110 (W) x 96 (H) x 31.2 (D) mm4-5/16" (W) x 3-3/4" (H) x 1-3/4" (D)


Call switch module (GT-SW)Power source Supplied from GT-DB/GT-DB-V/GT-DB-VNAmbient temperature - 10°C - +60°C (+14°F - +140°F)Material Self-extinguishing ABS plastic

Dimensions90.5 (W) x 106 (H) x 42.5 (D) mm3-9/16" (W) x 4-3/16" (H) x 1-11/16" (D)


1-call button panel (GF-1P)/2-call button panel (GF-2P)/3-call button panel (GF-3P)/4-call button panel (GF-4P)

MaterialPanel: Zinc die castWindow: PolycarbonateBottom: Chrome plated zinc die cast


Dimensions110 (W) x 95.2 (H) x 15.8 (D) mm4-5/16" (W) x 3-3/4" (H) x 5/8" (D)

Mass

GF-1P: Approx. 180g (0.40 lbs.)GF-2P: Approx. 190g (0.42 lbs.)GF-3P: Approx. 190g (0.42 lbs.)GF-4P: Approx. 200g (0.45 lbs.)

10-key module panel (GF-10KP)

MaterialPanel: Zinc die castBox: Chrome plated steel




Address module (GF-AD)

Power source Supplied from GT-DB/GT-DB-V/GT-DB-VNAmbient temperature - 10°C - +60°C (+14°F - +140°F)Material Self-extinguishing ABS plastic

Dimensions105.6 (W) x 88.3 (H) x 42.5 (D) mm4-3/16" (W) x 3-1/2" (H) x1-11/16" (D)


Address module panel (GF-AP)

MaterialPanel: Zinc die castWindow: Polycarbonate




Blank panel (GF-BP)

Material Zinc die castColor Metallic beige



4-module front frame (GF-4F)/3-module front frame (GF-3F)/2-module front frame (GF-2F)

MaterialFront frame: Zinc die castMounting bracket: Stainless steel


Dimensions

GF-2F: 135 (W) x 225 (H) x 16 (D) mm5-5/16" (W) x 8-7/8" (H) x 5/8" (D)



Mass

GF-2F: Front frame: Approx. 400g (0.89 lbs.)Mounting bracket: Approx. 200g (0.45 lbs.)

GF-3F: Front frame: Approx. 490g (1.09 lbs.)Mounting bracket: Approx. 250g (0.56 lbs.)

GF-4F:Front frame: Approx. 660g (1.46 lbs.)Mounting bracket: Approx. 290g (0.64 lbs.)

- 55 -



All-in-one entrance station (GT-DMB-N/GT-DMB-LVN)


Ambient temperature - 10°C - +60°C (+14°F - +140°F)

MaterialPanel: Stainless steelCase: Self-extinguishing ABS resin

ColorPanel: Stainless steel with hairline fi nishingCase: Black

Dimensions

GT-DMB-N: 150 (W) x 320 (H) x 38.2 (D) mm5-7/8" (W) x 12-5/8" (H) x 1-1/2" (D)

GT-DMB-LVN: 150 (W) x 425 (H) x 38.2 (D) mm5-7/8" (W) x 16-3/4" (H) x 1-1/2" (D)

MassGT-DMB-N: Approx. 1,200g (2.70 lbs)GT-DMB-LVN: Approx. 1,500g (3.3 lbs)

Guard station

Guard station (GT-MKB-N)


Communication

Open voice: Voice-actuatedHandset: Voice-actuated/Full-duplex (only when the other side is talking using the handset of GT-MKB-N or GT-1D)

Ambient temperature 0 - 40°C (+32°F - +104°F)Monitor 3.5 inch TFT color LCD

MountingDesktop use (with desktop stand) or surface wall-mount

Material Self-extinguishing ABS resinColor Black

Dimensions250 (W) x 189 (H) x 59 (D) mm 9-13/16" (W) x 7-7/16" (H) x 2-5/16" (D)

MassApprox. 820g (1.81 lbs)

When used with desk stand: Approx. 1,200g (2.70 lbs)

Door station

Vandal-resistant video door station (surface-mount) (JO-DV)Power source Supplied from guard stationCommunication Open voice hands-free communicationAmbient temperature - 20°C - +60°C (- 4°F - +140°F)

MaterialFront panel: Zinc die cast Main unit: Self-extinguishing

Color Front panel: Silver

Dimensions98 (W) x 173 (H) x 27 (D) mm3-7/8" (W) x 6-13/16" (H) x 1-1/16" (D)

Mass Approx. 650g (1.44 lbs.)Remarks IP54, IK08

- 56 -


3 SOFTWARE LICENSENotice regarding softwareUse of the software installed on this product has received direct or indirect authorization from third parties.

(1) GPL/LGPLThis product includes software components subject to the GPL/LGPL.Customers can obtain, modify, and re-distribute the source code of the software components according to the GPL/LGPL.

Open source codeThis product includes software components subject to the GPL/LGPL, and customers can obtain, modify, and re-distribute the source code of the software components according to the GPL/LGPL. In addition, you can fi nd details on the GPL/LGPL through the following links.

http://www.gnu.org/licenses/gpl.html

http://www.gnu.org/licenses/lgpl.html

Please confi rm the following contents when downloading.

<<Please confi rm>>

■ According to GPL/LGPL, the source code of the software components is not guaranteed, including warranty on “merchantability” or “suitability for a particular purpose.”

■ The source code of the software components are according to the “status quo,” and are provided based on the GPL/LGPL.

■ Please understand that we cannot answer questions regarding the content of the source code of the software components.

BSD License

Copyright (c) 2017, AIPHONE CO.,LTDAll rights reserved.

Redistribution and use in source and binary forms, with or without modifi cation, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The views and conclusions contained in the software and documentation are those of the authors and should not be interpreted as representing offi cial policies, either expressed or implied, of the FreeBSD Project.

Hereafter referred to as the link

- 57 -


4 REGULATIONS

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician

for help.

INDUSTRY CANADA

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

RED

Hereby, Aiphone Co., Ltd. declares that the radio equipment type [GT-DB-VN, GT-DMB-N, GT-DMB-LVN, GT-MKB-N, GT-BCXB-N] is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: http://www.aiphone.net/

GT-MKB-N: 13.56MHz / Max. 20.0 dBm

GT-DMB-N: 13.56MHz / Max. 20.0 dBm

GT-DMB-LVN: 13.56MHz / Max. 20.0 dBm

GT-DB-VN: 13.56MHz / Max. 20.0 dBm

GT-BCXB-N: 13.56MHz / Max. 20.0 dBm

NCC

電信法第48條

低功率電波輻射性電機管理辦法

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或

使用者均不得擅自變更頻率、加大功率或變更原設計之特性及

功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經

發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續

使用。

前項合法通信，指依電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻

射性電機設備之干擾。

WEEE

The object area of is the EU.

- 58 -


5 WARRANTYAiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of 2 years after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the fi nal decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, power surge, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. This warranty is limited to the standard specifi cations listed in the operation manual. This warranty does not cover any supplementary function of a third party product that is added by users or suppliers. Please note that any damage or other issues caused by failure of function or interconnection with Aiphone products is also not covered by this warranty. Aiphone will not be responsible for any costs incurred involving on site service calls. Aiphone will not provide compensation for any loss or damage incurred by the breakdown or malfunction of its products during use, or for any consequent inconvenience or losses that may result.

Issue Date: Jun. 2017B P0617 SZ 59038 AIPHONE CO., LTD., NAGOYA, JAPAN

http://www.aiphone.net/

OPERATION MANUAL - AIPHONE · 2018-08-07 · OPERATION MANUAL Thank you for selecting Aiphone for...

Documents

Transcript of OPERATION MANUAL - AIPHONE · 2018-08-07 · OPERATION MANUAL Thank you for selecting Aiphone for...