Operating Instructions

GSM Alarm Device with GPS Tracking „GX111“ Item No. 1168681

2

Table of ContentsPage

1. Introduction ..........................................................................................................................................................42. Explanation of Symbols .......................................................................................................................................43. Intended Use .......................................................................................................................................................54. Scope of Delivery .................................................................................................................................................55. Safety Information ................................................................................................................................................66. Notes on Rechargeable Batteries ........................................................................................................................77. General Information .............................................................................................................................................8 a) General Descriptions .....................................................................................................................................8 b) Operating Mode .............................................................................................................................................9 c) Alarm Mode .................................................................................................................................................10 d) Housing/Operating Elements ....................................................................................................................... 11 e) Description of the Connections ....................................................................................................................13 f) Notes on Use ...............................................................................................................................................13 g) Notes on Connection ...................................................................................................................................138. Commissioning - First Steps ..............................................................................................................................14 a) Assembly and Charging of the Product .......................................................................................................14 b) Changing the PIN Code to „1513“ ...............................................................................................................15 c) Micro SIM Card Insertion .............................................................................................................................159. ConfigurationviaTextMessage .........................................................................................................................1610. Functional Descriptions .....................................................................................................................................18 a) Determining„STATUS“ ................................................................................................................................18 b) GeneralConfigurationCommands ..............................................................................................................19 1. Changing the PIN Code („PIN“) ...............................................................................................................19 2. Changing the Device Name („NAME“) ....................................................................................................19 3. Setting the Language (Function „LANGUAGE“) ......................................................................................20 4.AdministrationofthePhoneBook(Functions„TEL“,„TEL1“,…) .............................................................20 c) ConfigurationoftheSensors .......................................................................................................................22 1. Setting Support („DIAGNOSE“) ...............................................................................................................22 2. Shock („SHOCK“) ....................................................................................................................................23 3. Position Change („SLOPE“) ....................................................................................................................25 4.BrightnessChange(„LIGHT“) ..................................................................................................................26

(

3

Page 5.TemperatureLimits(„TEMP“) ..................................................................................................................27 6. Panic Alarm („S1“) ...................................................................................................................................28 d) Additional Functions ....................................................................................................................................2811. Location Determination ......................................................................................................................................29 a) General GPS Localisation („GPS“) ..............................................................................................................29 b) Submission of a Web Link with GPS Position („GPSMAP“) ........................................................................30 c) ReadingDate/TimeandSynchronisingclock(„GPSDATE“) .......................................................................30 d) ActivatePositionTracking(„TRACK“) .........................................................................................................31 e) Programming the GPS Zone („GPSZONE“) ................................................................................................3212. EmailDispatchoftheTrackingData ..................................................................................................................34 a) ConfigurationoftheSMTPAccessData(„SMTP“) .....................................................................................35 b) ConfigurationoftheGPRSAccessData(„GPRS“) .....................................................................................36 c) TransmissionoftheTrackingData(„TRACKDATA“) ...................................................................................3713. System Functions ..............................................................................................................................................39 a) TimebetweenTwoAlarmMessages(„IDLEALARM“) .................................................................................39 b) Online/OfflineTimesofGSM(„TIMEOUT“) .................................................................................................4014. ERROR and LED Flashing Sequences .............................................................................................................42 a) „ERR“ LED ...................................................................................................................................................42 b) „GSM“ LED ..................................................................................................................................................43 c) „AKKU“ LED ................................................................................................................................................43 d) „GPS“ LED ...................................................................................................................................................4315. Reset to Default .................................................................................................................................................4416. Maintenance and Cleaning ................................................................................................................................4417. Declaration of Conformity (DOC) .......................................................................................................................4518. Disposal .............................................................................................................................................................45 a) General Information .....................................................................................................................................45 b) Batteries and Rechargeable Batteries .........................................................................................................4519. TechnicalData ...................................................................................................................................................46

4

1. IntroductionDearCustomer,thank you for purchasing this product.ThisproductcomplieswiththestatutorynationalandEuropeanrequirements.Tomaintainthisstatusandtoensuresafeoperation,youastheusermustobservetheseoperatinginstructions!

Theseoperatinginstructionsarepartofthisproduct.Theycontainimportantnotesoncommissioningandhandling.Alsoconsiderthisifyoupassontheproducttoanythirdparty.Therefore,retaintheseoperatinginstructionsforreference!

All company names and product names are trademarks of their respective owners. All rights reserved.If there are any technical questions, please contact:International: www.conrad.com/contact

United Kingdom: www.conrad-electronic.co.uk/contact

2. Explanation of Symbols An exclamation mark in a triangle indicates important notes in these operating instructions that must be

strictly observed.

Thearrowsymbolindicatesthatspecialadviceandnotesonoperationareprovidedhere.

5

3. Intended UseTheproductservestomonitoryourproperty.Itmustnotbeusedtomonitorpersons.Sensorsforshock,positionchange,brightnessmeasurement,andtemperaturemeasurementarebuilt-in.The integratedGPS receiver serves precise determination of the position,GeoFencemonitoring and tracking ofposition data.All functions can be controlled remotely by text message.Any use other than that described above can damage the product and may involve additional risks such as short circuit,fire,electricshock,etc.Nopartofthisproductmustbemodifiedorconverted.Thesafetyinformationmustbeobservedatalltimes!ThisproductcomplieswiththestatutorynationalandEuropeanrequirements.Allcompanynamesandproductnamesare trademarks of their respective owners. All rights reserved.

4. Scope of Delivery• GX111withrechargeablebattery• MiniUSBcable• Briefinstructions

Themainmanualfortheproductisavailableviadownload.

Up-to-date operating instructions Todownload the latest operating instructions, visitwww.conrad.com/downloads or scan the QR code on this page. Follow the instructions on the website.

The following accessories are needed for operation. They are not enclosed:• Micro-SIMcard(eitheraprepaidcardoraconventionalcontractcard)

Important! SetthePINofthiscardto1513beforeinsertingitintotheGX111.• Phillipsscrewdriver(sizetomatchM2screws)toopenthecoverflaps

6

5. Safety Information The guarantee/warranty will expire if damage is incurred resulting from non-compliance with these

operating instructions. We do not assume any liability for consequential damage! Nor do we assume any liability for damage to property or personal injury caused by improper use

or failure to observe the safety information. The warranty/guarantee will expire in such cases!

• For safetyandapproval reasons,unauthorisedconversionand/ormodificationof thedevicearenotpermitted. Never dismantle the product.

• Theproductisnotatoyandmustbekeptoutofreachofchildren.Theproductcontainssmallpartsanda rechargeable battery. Operate the product in a way that it is out of reach of children.

• Donotusethisproductinhospitalsormedicalfacilities.TheGSMradiosignalsmaycausefunctionalimpairmentinlife-maintainingsystems.Thesamemayapplyinotherareas.

• Handletheproductwithcare;impacts,shockorfallevenfromlowheightswilldamageit. • Theproductonlyservestotriggeralarmsbutdoesnotrelievetheuserfromhisdiligenceobligation. TheGPSfunctionsonlyservetomonitorproperty.Youarepersonallyresponsibleforcompliancewith

the statutory requirements for further monitoring. • Ifyoufindanydamageattheproduct,stopoperatingitandtakeittoaspecialistworkshop. It can be assumed that safe operation is no longer possible if: - the product is visibly damaged - the product no longer functions - the product was stored under unfavourable conditions for an extended period of time - if it was subjected to heavy stress during transport • Iftheproductisbroughtfromacoldintoawarmroom(e.g.intransport),itispossiblethatcondensation

develops. Therefore,firstlettheproductreachroomtemperaturebeforeconnectingittothepowersupply.This

may take several hours. • Donotleavethepackagingmateriallyingaroundcarelesslyasitcanbecomeadangeroustoyforchild-

ren. • Ifthereareanyquestionsthatarenotansweredinthisoperatingmanual,contactourtechnicalsupport

or another expert.

7

6. Notes on Rechargeable Batteries• Batteriesdonotbelonginthehandsofchildren.• Donotleaverechargeablebatterieslyingaroundopenly.Childrenorpetsmayswallowthem.Ifswallowed,consult

a doctor immediately.• Leakingordamagedrechargeablebatteriesmaycausecausticburnsiftheycomeintocontactwithskin.Therefore

you should use suitable protective gloves for this. • Liquidsleakingfromrechargeablebatteriesarechemicallyhighlyaggressive.Objectsorsurfacesthatcomeintocontactwiththemmaytakeseveredamage.Therefore,keeprechargeablebatteriesinasuitablelocation.

• Makesurethatrechargeablebatteriesarenotshort-circuited,dismantledorthrownintofire.Thereisadangerofexplosion!

• Alwaysobservecorrectpolarity (observeplus/+andminus/-)whenconnecting the rechargeablebattery to theGX111.

• UseonlytheenclosedrechargeablebatteriesoraccessoryrechargeablebatteriesofthesamebuildtosupplytheGX111withpower.

• Ifnotusedforalongerperiod(e.g.incaseofstorage),removetheinsertedrechargeablebatteryfromtheGX111.Iftherechargeablebatteryistooold,itmayleakandcausedamagetotheproduct,whichleadstothecancellationofthewarranty/guarantee!

• Adamagedrechargeablebatterymustnolongerbeused.Disposeofitinanenvironmentallycompatiblemanner.• Readchapter„Disposal“abouttheenvironmentallyfriendlydisposalofbatteries.

8

7. General InformationTheseoperatinginstructionsdescribethefunctionandoperationatthetimeofprinting(27January2014).Changesthatserveproductimprovementcanbeperformedbythemanufactureratanytime.Themostrecentoperatinginst-ructions will be provided on the associated product page on www.conrad.com in a timely manner.TheGX111hasanupdatefunction.However,anupdateshouldonlybeperformedtosolvewrongbehaviour.Everyupdateprocesshasrisks(e.g.cancellationduringtheupdate,etc.).Itmustbeassumedthattheproductmustbesentto the manufacturer after a defective update process. Inthefollowing,themostimportantitemsthatyoumustobservewhenusingtheproductarenoted.

Alltextmessageanswerexamplesaretobeunderstoodsymbolically.Actualimplementationmayvary.Theexamples should only show the information on the format and writing to be expected.

Priortocommissioningoftheproduct,checkwhetheritisgenerallysuitedfortheintendedapplication!Ifindoubt,askasuitablespecialist.

a) General DescriptionsThisproductistobeusedtomonitorthecustomer‘sproperty.Incaseofalarm,itstaskistoinformthecustomerofitby text message as quickly as possible. Itmaymonitorshock,positionchanges,brightnessdifferencesandtemperature.Incaseofalarm,theGX111sendsan alarm text message to up to 4 stored phone numbers.TheGPSreceiverisusedtodetermineandmonitorGPSzones(„GeoFence“),i.e.aplaceorareawheretheproductmay be present. Theproductisdesignedformaximumbatterylife.Theregularconditionissleepmode,whereonlytheconfiguredsensorsareactive.Theywakeupthemoduletosendtextmessagealarmsifathresholdisexceeded.Apartfromthis,themodulewillwakeupevery24h,e.g.for15minutes(default)andwillcheckforanytextmessagesreceived.Uponreceiptofatextmessage,the„ONLINE“timeoutisresetandcanbeconsideredfurther.Duringthistime,e.g.thecurrentpositioncanbedetermined.ForthisitispossibletohavealinktoOpenStreetMap.org(open-source map provider) sent by text message command. Furthermore,theproductmayalsorecordandsave(track)thecurrentGPSposition.Thesesaveddatacanbereadby USB.

9

b) Operating ModeTheproduct isoptimised for the longestbattery life.This isachievedby targeteddeactivationof theGSM-/GPS-module („OFFLINE“ mode). Fortheproducttocontinuetobeavailable,theGSMmodulewillwakeupautomaticallyafteraspecifictime(„ONLINE“mode)andcheckwhetherthereareanynewtextmessages.Thestandardsettingsare15minutesforthe„ONLINE“modeand1425minutesforthe„OFFLINE“mode(15+1425=1440minutes=24h).The„TIMEOUT“commandcanbe used to change these settings on demand (described farther towards the back of these instructions).

A sensor alarm or push on the external button „S1“ will wake up the module at once.Eachuseractivity (textmessage,USBdata)willalsoreset theactive timeout;youwillhave15minutes‘ time(bydefault) again after each action.

10

c) Alarm ModeThereistheimportantalarmmodeinparalleltoandindependentoftheoperatingmode.ThismodedefineswhethertheGX111is„armed“asanalarmdeviceandmaysendtextmessagealarmswhensensorsaretriggeredandoptio-nally issue an alarm sound. Theconditionsareasfollows: ENABLE ALARM #1513 Thealarmmodeisswitchedon. DISABLE ALARM #1513 Thealarmmodeisswitchedoff.

Alarm mode on:Thismodeisenteredviathecommand„ENABLEALARM#<PIN>“.Whetherthealarmmodeisactiveornotcanonlyberequestedviathecommand„TESTSTATUS#1513“.Ifthealarmmodeisonandrecognisesanalarmincidentviaanactivatedalarmsource(shock,position,…),allphonenumbersinthephonebookoftheGX111(nottheSIMcard!)will receive the corresponding alarm text message and an optional alarm sound can be issued. Alarm mode off:Inthismode,GSMcostsariseonlywhenanactionperformedbyyoucausesareactionoftheGX111.TheGX111onlysendsanswertextmessageswhenatextmessagewiththecorrectPINhasbeenreceived.TheGX111doesnotsendout any alarm text messages on its own.

Thealarmmodeis(deliberately)offbydefault. Observethathighcostsmayarisefromsendingtextmessages(particularlyabroad),dependingonhowthe

GX111isconfigured.

11

d) Housing/Operating Elements TheGX111hasnofurtherlabelsorLEDsontheoutsidebecauseitistobeasunobtrusiveandmergewith

its environment as well as possible. Thefigureshowsthehousingwithoutthefrontcap.

1 Lightsensor„LIGHT“2 USB-socket (charging rechargeable battery)3 Button„RESET“forresetting4 Button „S1“ (wake up)5 „GSM“ LED (green)6 „AKKU“ LED (yellow)7 Micro-SIMcardholder(setthecard‘sPINto1513!)8 „ERR“ LED (red)9 „GPS“ LED (blue)10 Screw connection11 Position of the GPS receiver in the housing

Find the description of the operating elements below:1 Lightsensor„LIGHT“ Thelightsensormeasurestheambiencebrightness.Thealarmvalueissetfrom1(bright)to10(dark).Whenthe

setbrightnessvalueisexceeded,analarmmessageissent.Thismaybeusedtodetect,e.g.,openingofacabinetorgate(lightingression)(command„LIGHT“).

Asaspecialproduct feature, the lightsensor reacts to theentirevisibleand invisible lightspectrum fromUV(ultraviolet,e.g.UV-lamps)toIR(infrared,e.g.IR-remotecontrols).

Therefore,placetheGX111correctlybeforeassumingincorrecttriggering.

1 2 3 11

910

8 7 6

4510

12

2 USB-socket (charging rechargeable battery) TherechargeablebatteryoftheGX111ischargedviatheUSBsocketandaninterfaceisprovidedforcontrol/

configurationoftheGX111.Permanentoperation(powersupply)viaUSBispossibleaswell. ConnectedtothePC,adriverisneededforthe„virtualCOMport“sothattheGX111canbeconfigured/controlled

viaUSBandafirmwareupdateperformed.Therequiredsoftwareandfirmwarefilesareavailableonlineatwww.conrad.com,inthedownloadsectionfortheproduct.

TheGX111mustonlybeusedwiththeofficiallyprovidedsoftware(downloadareaontheproductwebsite).3 Button„RESET“forresetting ThisbuttonisusedtorestarttheGX111. Incombinationwith thebutton„S1“, theGX111 is reset to factorysettings.Formore information,seechapter

„Factory settings“ farther back in these operating instructions.4 Button „S1“ (wake up) ThisbuttonwakesuptheGX111sothatitcanbeconfiguredinthe„ONLINE“modeviatextmessage.USBcon-

figurationisonlypossiblein„ONLINE“modeeither. Thebuttonforpanicalarmcanbeconfiguredaswell.Oncethebuttonispushed,atextmessagealarmissent

when the alarm mode is activated (command „S1“).5 „GSM“ LED ThisLEDisusedtorecognisetheactivityandstatusoftheGPSmoduleintheGX111.Inthe„ONLINE“mode,this

LEDwillalwaysflashorbelit. AmoredetaileddescriptionofthisLEDisfoundinthechapterondescriptionoftheerrorcodesandLEDflashing

sequences.6 „AKKU“ LED (yellow) TheinternalrechargeablebatteryischargedandmonitoredviaachargingelectronicsystemintheGX111.For

moreinformation,seethechapterondescriptionoftheerrorcodesand‎LEDflashingsequences.7 Micro SIM card holder ThemicroSIMcardholderisusedtoholdanymicroSIMcard.

TheGX111canonlybeactivatedwiththemicroSIMcardinserted.TheSIMcardholderrecognisesinser-tionofthecardandreleasestheremaininghardwareoftheGX111.

WithouttheinsertedSIMcard,onlychargingoftherechargeablebatteryviaUSBisavailable,butnootherfunctions!

ObservethatconsiderablecostsmayarisefrommobilephonedataconsumptionwhenusingtheSMTPand GPRS functions.

13

8 „ERR“ LED (red) ThisLEDisusedas„Error“LEDandwillinformofactivitiesorerrorsaccordingtothechapterondescriptionof

theerrorcodesandLEDflashingsequences.9 „GPS“ LED (blue) ThisLEDindicatesactivitiesoftheGPSmodule.Alsoobservethechapterondescriptionoftheerrorcodesand

LEDflashingsequences.10 Screw connection Thecovercapisattachedhere.11 Position of the GPS receiver in the housing TowarrantbestGPSreception,theGX111musthaveafreeviewoftheGPSsatellitesinthesky.

e) Description of the USB socketThisconnectionisusedtochargetherechargeablebatteryofthedevicewithachargingcurrentof100mA.Thisdoesnot require drivers and any commercial USB plug-in mains unit can be used. A higher charging current (500 mA) requires release from a USB host (e.g. PC with USB-port). Only then will the charging times described in the technical data be available. Data communication takes place via a standard USB chip that signs on to the Windows-PC as a virtual COM port. Thecorrespondingdrivercanbeprocuredeitherfromwww.conrad.comordirectlyfromthemanufacturer‘swebsite:http://www.ftdichip.com/Drivers/VCP.html

f) Notes on Use• Thereisnoprescribedusageposition.• WhenusingtheUSBsocket,observethatthereisenoughroomfortheplug.Lateralforcesontheplugged-inplugcanleverthesocketfromthePCBandthuscauseirreparabledamage,lossofwarranty/guarantee!

• Towarrantthedevicefunction,chooseasiteofusewheretheGMSnetworkreceptionisasgoodaspossibleandthe GPS signal can be received.

• Theproductshouldbetakentoasitewhereobjectshockcanbemeasured(„SHOCK“alarm).

g) Notes on Connection• Theexternalcablesmustbekeptasshortaspossibleandremaininglinelengthsmustnotbecoiled.Themaximum

line length is 3 m.• Too-strongtemperaturefluctuationsmayleadtotemporaryimpairmentandrequiremanualresetinextremecases.• Theproductisnotintendedforthe„Safety“areaandalsodoesnotcorrespondtoanySIL/ASILlevel.

14

8. Commissioning - First StepsThefollowingisneededforoperationandconfigurationofthedevice:• AconventionalmobilephonethatpermitsinsertionofamicroSIMcardforconfigurationoftheGX111.

Ifyourmobilephoneisnotequippedforusewithamicro-SIMcard,youwillneedthecorrespondingadap-ter.

• AnadditionalmicroSIMcardfortheGX111• AUSBport(PC,notebookorincludedmainsadapter)withUSBcable• AsmallPhillipsscrewdriverforM2screwstoremovethecoversoftheGX111

a) Assembly and Charging of the ProductTheproductisdeliveredwiththerechargeablebatteryinserted.However,itisnotconnectedtopreventdeepdischar-ge.Therefore,thehousingoftheGX111mustbeopenedandthePCBremovedforfirstcommissioning.Thentherechar-geablebatterycanbeconnectedandtheGX111assembledagain.Particularly observe the following items during assembly:Rechargeable battery connection:ThereisaconnectionfortherechargeablebatteryonthePCBsidewiththeSIMholderrightnexttoit.Theplugispushedontotheholderfromthetop.Theplugisprotectedagainstpolarityreversal.

Rear cover (without opening for light sensor)ThecoverisfirmlyscrewedtothehousingandcoversthelargeopeningwiththePCBandtherechargeablebattery.Thecovermustberemovedtoreplacetherechargeablebattery.ThenthePCBwiththerechargeablebatterycanbepulled from the housing. Whenputtingittogether,observethatthesealonthecoverinsideisplacedcleanlyandhasnodamage.Therubberwashersalsomustbeusedforscrewingtoensurebestweatherresistance.Front coverThiscovercoversallconnectionsandstatusLEDsandhasonlyatransparentopeningforthelightsensor.Onlythiscoverneedstobeunscrewedforregularaccesstotheproduct(USB,SIM,etc…).Therequirementstoassemblyofthefrontcoverarethesameasfortheinternalcover.However,observethatthetransparent opening should be checked for contamination so that the light sensor can work properly.

15

b) Changing the PIN Code to „1513“EverySIMcardhasaPINcode.BecausethisGSMproductusesitsownPINprocessingforreasonsofsafety,theSIM card PIN code must be changed to that of the product.The following steps are required for this:• ThemicroSIMcardintendedfortheproductmustbeinsertedinamobilephone.Ifyourmobilephoneisnotequip-pedforusewithamicro-SIMcard,youwillneedthecorrespondingadapter.

• Accordingtotheoperatinginstructionsofthemobilephone,thePINcodemustbechangedto1513.• ThemicroSIMcardwiththechangedPINcodemustberemovedfromthemobilephone.• ThemicroSIMcardwiththechangedPINcodecannowbeinsertedintotheGX111(seenextchapter).

We urgently advise against deactivating the SIM card PIN query. In addition to the risk at theft and con-nectedillegaluse,deactivationofthePINfunctionmeansthatthedeviceisusedinanon-intendedmode.Theremaybefunctionalerrors!

c) Micro SIM Card InsertionThemicroSIMcardwiththePINnumber„1513“mustbeinsertedintheintendedSIMcardholderoftheGX111.AfterinsertionofthemicroSIMcard,theGX111isswitchedon.DuringstartingoftheGX111,the„ERR“LEDflashesatanintervalofonesecond.Afterashorttime,the„GSM“LEDwillflashgreen(inintervalsof½second)(networkscanning)andafterafewseconds,the„GSM“LEDshouldchangeitsflashingpattern.Ifthe„GSM“LEDdoesnotchangeitsflashingpattern,thereisnoconnectiontotheGSMnetwork.Inthiscase,thenetworkqualityandfunctionofthemicroSIMcardatthesiteoftheGX111mustbeinspectedwithaseparatemobilephone.Use a mobile phone to check if the SIM card is activated at all. If the mobile phone cannot log into the GSM network withthesetPIN1513,thereisaproblemwiththeSIMcard.Inthiscase,contacttheprovideroftheSIMcard.IfanerroroccurswhileconnectiontotheGSMnetworkisestablished,itissignalledwiththe„ERR“LED.Inthiscase,pushthe„RESET“buttonattheGX111.

IftheGX111usedtobeusedwithanotherSIMcard,thereistheoptionofthePINnumberintheproductbeingchangedandnownolongermatchingthedefaultsetting„1513“.Inthiscase,theGX111mustberesettofactorysettings(seecorrespondingchapterfartherbackintheseoperatinginstructions),thenthePIN of the micro SIM card must be set to „1513“ in the mobile phone.

ThemicroSIMcardmayhavebeenlockedinthemeantimeandmustbeunlockedwiththePUK.Inthiscase,useaseparatemobilephoneandunlockthemicroSIMcard.

16

9. Configuration via Text MessageToreceivethefullfunctionalscopeoftheGX111,itmustfirstbeconfigured.TheentireconfigurationisperformedbysimpletextmessagecommandsyousendtotheGX111(thephonenumberofthemicroSIMcardintheGX111)fromyour mobile phone.Thismethodmakesitpossibletoactivate,deactivateorchangethesettingsoftheGX111fromanywhere.Alternatively,theGX111canbeconfiguredviatheUSBinterfaceusingPCsoftware(availableviawww.conrad.com).

TheseoperatinginstructionsdonotdealwithconfigurationviaPCsoftware.Thisonlydescribeshowtheproductcanbecontrolledviaamobilephone,withoutanyotheraids.

Toprotectagainstunauthorisedaccess,theGX111generallyreactstoauthenticatedmessagesonly.Inatextmessage,youauthenticateyourselfbyincludingthecorrectSIMPINoftheGX111(nottheoneofthemobilephoneonwhichthetextmessagehasbeenwritten!).

Foryourownsafety,theSIMPINnumbermustbechangedunderallcircumstancesaftercommissioningoftheproduct.Thisisdescribedinthecorrespondingchapter.

IftheGX111isin„OFFLINE“mode(controlcommandsviatextmessagearenotpossible),theGX111canbeputinto„ONLINE“modebypushingthebutton„S1“onitsside.Thestandardsettingsare15minutesforthe„ONLINE“modeand1425minutesforthe„OFFLINE“mode(15+1425=1440minutes=24h).

Introduction into the command formatThetextmessagestoprogramtheGX111aresetupaccordingtothefollowingchart: <ACTION> <FUNCTION> <PARAMETER1> <…> <#PIN>Examples: SET TEL1 +49177556644221 #1513 (phonebook) RESET TEMP #1513 (alarmoff) TEST TEMP #1513 (query) ENABLE ALARM #1513 (alarmon) DISABLE ALARM #1513 (alarmoff)

Important! EverytextmessagesenttotheGX111mustendwiththePINsetasprotection.Without„#<PIN>“atthe

endofthetextmessage,itisdiscardedandnoansweringtextmessagewillbegenerated! Thecommandsandparametersmustbeseparatedbyasinglespaceeach. IftheGX111doesnotreact,itmaybein„OFFLINE“mode.Pushthelateralbutton„S1“towakeitup.

17

„ACTION“The„ACTION“commandspermitthefollowing:SET =switchon/activate/configureRESET =switchoff/deactivate/factorysettingsTEST =test/check/requestENABLE =activatethealarmsystem(onlyforthefunction„ALARM“)DISABLE =deactivatethealarmsystem(onlyforthefunction„ALARM“)

Noteonthe„RESET“command: Ifafunctionistobeswitchedofforresetduetoanerror,thecorresponding„RESET“actionmustbeused

with thecorresponding functionword!Thisaction isuniversallyapplicable toall functions/textmessagecommands and resets the corresponding function to the default settings.

„FUNCTION“Thisisusedtoselectthefunctionyouwanttochangeorperform:TEL1 =phonebookentryno.1NAME =NameoftheGX111

„PARAMETER“Boththepresenceandthenumberofparametersdependonthefunctionandactionused.Therefore,most„RESET“actionshavenoparameterswhile „SET“actionswithoutparametersare rather rare (whatshouldbeset towhichvalue). A parameter may be the following:List: Youmaychooseaparameterfromapre-definedlist. e.g.:DE,EN Writing:<DE/EN>Number: An integer without decimal digits. e.g.:60=time[seconds](SETIDLEALARM60#1513)

More information:• Capitalisationisnotrelevant;youmayusecapitalandsmalllettersasyouwish.• Everynewcommandofthesamefunctionwilloverwritetheprevioussettings.• Aftereveryvalidtextmessagecommand,theGX111willsendatextmessageanswertoconfirmprogrammingto

your mobile phone (if the PIN in the text message command was correct).

18

10. Functional Descriptions ThefollowingexamplesassumethatthePINis„1513“.

Theaction„TEST“ALWAYScontainsansweringwiththecorrectparametersforthefunctionandthusisnotindicated. Several functions share one answer text message to use the maximum of a text message.

Theaction„RESET“isALWAYSresettingofafunctiontothefactorysettings(allparameters).Deviationsare indicated separately below.

a) Determining „STATUS“Thecommand„STATUS“returnsasummaryofthemostimportantsettingsandconditionsoftheGX111. TEST STATUS #1513ThentheGX111sendsananswertextmessage.Example(therightcolumnshowsonlyadescription;itisnotcontainedinthetextmessage): GX11101.XX NameoftheGX111,firmwareversion GSM: 59% GSM signal strength GPS: on GPS receiver is on TEMP:28CCurrentlymeasuredtemperature Accu: 75% Current charge condition of the rechargeable battery Slope: 0 degree Measured position angle 0° or no reference angle set Diagnose: off Diagnosis mode off Alarm: Disabled Alarm treatment via text message deactivated

19

b) General Configuration CommandsThissub-chapterdescribesallgeneralconfigurationcommands.

1. Changing the PIN Code („PIN“)TosecuretheGX111fromunauthorisedaccess,thestandardPIN„1513“maybesettoanyothervalue.ThePINcodecan be changed as follows: SET PIN <new PIN> #<old PIN>Example: Changing old PIN 1513 to new PIN 1234: SET PIN 1234 #1513Foreverynewtextmessagecommand,thenewPINcodenowhastobeappended(tostickwiththeexample:1234),precededbyacrosshatch(#).IfthewrongPINcodeisenteredorthePINcodeisnotsent,youwillnotreceiveananswering text message. Changing of the PIN code will change both the settings of the product and the PIN code of themicroSIMcard!ThePINcodealwayshas4digits.Thereisno„TEST“actionfortestingthisfunction.

IfyoulosethePINcode,theGX111canberesettofactorysettings(seechapter„FactorySettings“).Allsettingswillbelostwhenresetting!Thenthedevicemustbesetagain.

ResettingtheGX111tofactorysettingswillnotaffectthemicroSIMcard.ThePINcodeofthemicroSIMcard is not changed.

2. Changing the Device Name („NAME“)IfseveralGX111areoperatedatthesametime,itisrecommendedtoassignadifferentnametoeachGX111.Thismakes it easier to assign alarm messages to the correct device.

Thedevicenamehasamaximumlengthof20characters.TochangethenameatyourGX111,sendthefollowingtextmessagecommand: SET NAME <new name> #1513Example: Renaming to „NEWNAME“: SET NAME NEWNAME #1513Youwillreceivethefollowingconfirmationtextmessage: NEWNAMEGX1111.xxToresetthedevicenametofactorysettings(noname),usethefollowingcommand: RESET NAME #1513

20

3. Setting the Language (Function „LANGUAGE“)TheGX111sendsalarmtextmessagesintheGermanlanguage.IfthetextmessagesaretobesentintheEnglishlanguage,sendthefollowingtextmessagecommandtotheGX111: SET LANGUAGE EN #1513ToreceivethetextmessageinGermanagain,sendthefollowingtextmessagecommandtotheGX111: SET LANGUAGE DE #1513

4. Administration of the Phone Book (Functions „TEL“, „TEL1“,…)TheGX111cansaveupto4phonenumbers.Incaseofalarm,anotificationtextmessageissenttoeachofthesephonenumbers.Thesephonenumberscanalsousethefunction„INCALL“.

Ifthesamenumberisinthelistseveraltimes,itwillreceivethesametextmessageasmanytimes. TheGX111mayprocessphonenumbersinnationalandinternationalformat.However,theinternational

formatshouldbeusedatalltimes,sinceuseabroadmaycauseproblemsotherwise. Example:0172/xxxxxxxx(national)becomes+49172xxxxxxxx(international)Saving Phone NumbersUsethefollowingcommandtosaveaphonenumberintheGX111: SET TEL1 +49111… #1513 SET TEL2 +49222… #1513 SET TEL3 +49333… #1513 SET TEL4 +49444… #1513Thereistheoptionofprogrammingseveralphonenumbersinasinglecommand,e.g.3phonenumbers(TEL1toTEL3): SET TEL1 +49111… +49222… + 49333… #1513Concurrent programming of phone numbers is possible with a list starting from the indicated phone book entry and ending at the last phone book entry as follows: SET TEL1 <tel-nr1> <tel-nr2> <tel-nr3> <tel-nr4> #1513 SET TEL2 <tel-nr2> <tel-nr3> <tel-nr4> #1513 SET TEL3 <tel-nr3> <tel-nr4> #1513 SET TEL4 <tel-nr4> #1513

21

Aftersendingthecommand„SETTEL1....“,youwillreceiveatextmessageanswerwithalistofsavedphonenum-bers: GX1111.xx TEL1:+49111… TEL2:+49222… TEL3:+49333… TEL3:+49444…

Deleting the phone numbers savedTodeletephonenumber1and3,forexample,youneedtosendtwotextmessages: RESET TEL1 #1513 RESET TEL3 #1513Aftersendingthecommand„RESETTEL...“,youwillreceiveatextmessageanswer.

Testing phone numbersTocheckthephonenumbersstoredintheproduct,usethefollowingcommand: TEST TEL #1513Thetextmessagecommands(SETTEL1,SETTEL2,SETTEL3,…)withaspecifiedphonenumberonlychangethephonenumberofthecorrespondingmemory.Thenumbersoftheotherphonebookentriesareretained.

22

c) Configuration of the Sensors TheGX111hasvarioussensorsthatcanbeusedtotriggeranalarm.Theshocksensorreactstomechanicalshock,e.g. when an object drops down. Thepositionsensorrecognisesinclinations/positionchangesandfallingoveroftheobject.Thebrightnesssensorcanrecordachangeofbrightnessof theambience lighting,e.g.openingofadrawer (thesensoralsorecognisesUVandIRlight).Whether alarm is triggered at all (sending text message) is centrally controlled by the command „ENABLE ALARM“ or „DISABLE ALARM“.Thefollowingcommandsareusedtoconfigurewhichofthesensorsareallowedtotriggeralarmatonceandwherethe acceptance thresholds are.Everysensor‘ssensitivitycanbeset.Thebestsensitivitysettingsdependonmanyfactorssuchasinstallationsite,objectsize,etc.andmustbefoundindividuallybytesting.Thecommand„SETDIAGNOSE“canbeusedforthis.

Eachactivatedsensorwillconsumeenergy.Thisreducesthebatterylifeaccordingly.Togiveyoutimetoreacttotheevent,thesensorisdeactivatedforaspecificperiodoftime(defaultsetting:2minutes)afteranalarmandcannotsendanynewalarmtextmessages.Particularlywithfastsensors,suchasshocksensors,the „IDLEALARM“ function reduces the dispatch of text messages.

1. Setting Support („DIAGNOSE“)Thiscommandisusedtomakethesensorseasiertoconfigure.Afteractivatingthediagnosismode,exceedingofthethresholds (triggering of an alarm) is displayed by a permanently lit „ERR“ LED. Ifthethresholdisundercut(alarmisnottriggered),the„ERR“LEDisoff.Notextmessageissent.Thebasisisthecurrentsensorconfiguration.Thediagnosismodeisavailableforalarms„VOICE“(soundalarm),„SHOCK“(vibrationalarm),„LIGHT“(brightnessalarm)and„SLOPE“(positionchangealarm).

Itisnotpossibletodifferentiatebetweenwhichsensorwasresponsiblefortriggering.Therefore,theindivi-dual sensors should be tested separately.

Thefunction„DIAGNOSE“isonlyfunctionalwhenthealarmmodeison(„ENABLEALARM“).Thefollowingcommandisusedtoactivatethisfunction: SET DIAGNOSE #1513 ENABLE ALARM #1513Thefollowingcommandisusedtodeactivateit: DISABLE ALARM #1513 RESET DIAGNOSE #1513

Thefunction„ALARMSOUND“canbeusedtochecktheeffectsof<IDLEALARM>.Thecommand„DIA-GNOSE“keepstheGX111fromsendingtextmessagealarms.Theparallelfunction„ALARMSOUND“,incontrast,isnotimpairedbydiagnosismode.

23

2. Shock („SHOCK“)Thissensorreactstoshockfromanydirection.Aninternalmeasuredvalueisdeterminedthat isderivedfromtheacceleration. Even movements and permanent accelerations below the threshold do not trigger alarm.

Thefollowingcommandsetsthethresholdforshocktothevalue<threshold>andtheminimumtimeforoccurrenceof the shock to 1 second: SET SHOCK <threshold> #1513Threshold:1-10(1=minimumsensitivity,10=maximumsensitivity)

Thefollowingcommandsetsthethresholdforshocktothevalue<threshold>andtheminimumtimeforoccurrenceoftheshockto<triggertime>. SET SHOCK <threshold> <trigger time> #1513Threshold:1-10(1=minimumsensitivity,10=maximumsensitivity)Triggertime:1-255(seconds);thiscorrespondstothetimethatashockmustpersistbeforeanalarmistriggered.

Thefollowingcommandsetsthethresholdforshocktothevalue<threshold>andtheminimumtimeduringwhichnoshockoccursto<triggertime>.Theadditionalparameter„INV“invertsthealarmcriteria,i.e.thealarmistriggeredifthere is no shock for a set period of time. SET SHOCK <threshold> <trigger time> INV #1513Threshold:1-10(1=minimumsensitivity,10=maximumsensitivity)Triggertime:1-255(seconds);thiscorrespondstothetimethatashockmustnotoccurbeforeanalarmistriggered.Theinterrelationofshock,triggertime,idlealarmandalarmisillustratedbelow:

ALARMSMSStartIDLE

SET SHOCK 8

t

t

8/10

t

IDLETIMER

(IDLE) (IDLE)

SET SHOCK 8 1010 s 10 s

ALARM

<10 s 10 s

<10 sSET SHOCK 8 10 INV

ALARMSMSStartIDLE

ALARMSMSStartIDLE

24

Description:Thetoplineshowsthe„shockimpulses“abovethesetshockthreshold„8/10“.Aboveit,ithasbeenmarkedfromwhenonwards which „SHOCK“ settings are valid. Themiddlelineshowsthe„IDLETIMER“describedinthechapteronthecommand„IDLEALARM“.The„IDLETIMER“definestheshortestdistancebetweentwotextmessagealarms.Thisisparticularlyimportantforfastalarmsourcesthat would otherwise cause many alarm messages to be sent before you can react (e.g. shock from movement of a stolen vehicle).Thebottomlineshowswhenthesensorwouldtriggeranalarmmessage(„ALARMSMS“)atthevalidsettingsandwhichoneswouldbeblockedbythe„IDLETIMER“(„IDLE“).„SETSHOCK#1513“(withouttime)or„SETSHOCK1#1513“(time=1s)causeimmediatealarmonceashockisabovethethreshold.Theshockismeasuredat250kHz.Whenthealarmistriggered,the„IDLETIMER“isstartedatthesametime.Duringthistime,thesensorcannottriggeranewalarmeveniftheconditionforanewalarmwouldbe present.„SETSHOCKxxx#1513“ (xxx= time indicated inseconds) requiresall (!) sensor values tobeabove theshockthresholdwithinthese,e.g.,10seconds.

Observethatameasurementtakesplaceeverysecond.Accordingly,thevibrationmustnotceaseordropbelow the sensor threshold for more than 1 second since this would restart the time indication (10 se-conds).

Thisalsoappliestoinvertedmode(„INV“),whereatimeneedstobeindicatedaswell.However,thedistancebetweentheshocksismeasuredhere.Ifthetimesetsabovethesettriggertime,analarmisgenerated.

25

3. Position Change („SLOPE“) Thesamesensorasfor„SHOCK“isabletodeterminethedirectionofgravityandthusdefinethecurrentpositionoftheGX111.IftheGX111changesitsposition(angle,notlocation!),thismaybeusedtotriggeranalarm.Itisnotimportantwhichaxistheproductturnsaround,butthateachaxisislookedatseparately.

Thus,adiagonalcanleadtoahighertotalanglethanpermitted.Thismustbeobservedwhendeterminingthe threshold.

Theaxesrunalongthehousingedges.

Thefollowingcommandsetsthethresholdofapositionchangeto<slopethreshold>.Atthetime,thecurrentpositioninspaceissavedasareferencevalue.Ifthepositiondeviatesfromthesetreferencevaluebythesetthreshold,analarm is triggered. SET SLOPE <slope threshold> #1513Threshold:1-180(1=minimumslopeindegrees,180=maximumslopeindegrees)

Note: As a threshold, the angle change to the position is set inwhich the productwas at the time of „SET

SLOPE…“. Thecurrentlymeasuredvaluefor„STATUS“isalsobasedonthisreferenceposition. Thereisnodifferentiationbetweentheindividualaxes;themeasuredvalueoftheaxiswiththehighest

deviation is assessed and displayed at all times. Diagonal angles are not considered. A „diagonal“ zeropositionof theGX111can reduce theaccuracyof theangle calculation.TheGX111

therefore should always be in parallel with the surface of the earth on the one side.

Y

Z

X

26

4. Brightness Change („LIGHT“)Atthefront,thereisabrightnesssensorthatcanbeusedtomonitorlightintensity.Thefollowingcommandmeasuresthecurrentambiencebrightnessandsetsthenext-higher(!) thresholdasrefe-rence.Whenthis(higher)thresholdisexceeded,alarmistriggered. SET LIGHT #1513The followingcommandspecifies the indicatedambiencebrightness threshold.When this threshold isexceeded,alarm is triggered. SET LIGHT <threshold> #1513Threshold:1-10(1=minimumsensitivity,10=maximumsensitivity)Example: 1=GX111inadarkroomwillrecogniselight 10=GX111inabrightroomwillrecogniseadditionallightDeactivate the alarm with the following command: RESET LIGHT #1513

Thesensorhasawiderrangethanthehumaneye.Accordingly,observelightsourcesoutsideofthevisiblerange(IR=infraredandUV=ultraviolet),particularlyincaseofcontinuouswrongalarms.

Thecapanditswindowforthesensorreducesensitivityandthemeasurablespectrumoflight.Youneedtoconsidertheeffectsdependingonsiteofuse;inanycase,checkthatthealarmistriggeredcorrectlyattheinstallationsiteoftheGX111.

27

5. Temperature Limits („TEMP“)ThesensorislocatedonthePCBandthusonlydeterminesthetemperaturewithinthehousing.QuicktemperaturechangesthuscannotberecognisedsincethehousingoftheGX111hastoheatuporcooldownfirst.YoucansetaMAXandMINtemperaturevalueforthetemperaturesensor.IftheMINvalueisundercutortheMAXvalueexceeded,analarmmessageissenttoallstoredphonenumbers. SET TEMP <upper threshold> <lower threshold> #1513Upper threshold: max. 55 °C (corresponds to the standard value for the upper threshold)Lower threshold: min. -4 °C (corresponds to the standard value for the lower threshold)Example: SET TEMP 20 -2 #1513Atatemperatureof-3.0°Cor+21.0°C,theGX111willtriggeranalarm.

Thebatterycapacityverystronglydependsonambiencetemperature.Achargeconditionofthebatterythat would have lasted months at 20 °C may be able to send a single text message before emergency deactivationat0°C(protectionoftherechargeablebatteryfromdeepdischarge.Accordingly,aminimumtemperatureof,e.g.,10°Cissensible.

Theelectronicsassuchcanbearhighertemperatures,particularlyin„OFFLINE“mode.Thehousingandrechargeablebattery,however,cannotbeartoo-hightemperatures.Therefore,analarmvalueof+30°Cwould be sensible.

28

6. Panic Alarm („S1“)Thebutton„S1“atthesideofthehousingcantriggerapanicalarm.Totriggerthepanicalarm,pushthebutton„S1“for 3 seconds. Activate panic alarm: SET S1 #1513Deactivate panic alarm: RESET S1 #1513

Theanswertothiscommandcanbedelayedbyupto1minuteduetotheGPSsearch.Immediatelocali-sationismoreimportant,sincethisdocumentsthelocationoftheincident.Thetimeofreactiontothealarmtextmessage,incontrast,isnotknownatall-therefore,GPSsearchtakesprecedence.

d) Additional FunctionsAlarm History („ALARMHISTORY“)Thetriggeredalarmisloggedinthedeviceusingalist.Thelistcansave2730alarmentries.Ifthenumberofalarmsexceedsthethresholdof2730,theoldestentriesareoverwritten.

Sincethealarmentrycontainsthedateandtime,alarmentriesareonlywrittenintothelistifthedateintheGX111hasbeenset(seechapter„GPSDATE“).ThetimeisindicatedinUTC.

IfthefollowingcommandwassenttotheGX111,thetwolatestalarmsarereturned. TEST ALARMHISTORY #1513Ifmorealarmentriesaretobesent,youcanaddanotherparameter.Thisparameterisonlyconsideredwhensendingcommandbytextmessage,toavoidundesiredcosts. TEST ALARMHISTORY <n> #1513Theparameter<n>specifiesthenumberofAlarmentriestobesentout(1to10ofthelatestalarms).

Up to 2 Alarm messages from the history per text message can be sent.TodeletetheentirelistofalarmentriesintheGX111,usethefollowingcommand: RESET ALARMHISTORY #1513

29

11. Location DeterminationTheGPSreceivercanbeusedtodeterminethecurrentGPSposition.Furthermore,youcanbeinformedwhentheGX111leavesapre-defined(permitted)area(„GeoFence“).All functions inconnectionwithpositiondeterminationare explained below. First a few technical notes:

DependingonreceiverpositionintheGX111,sightconnectiontotheskyandtheweathersituation,itmaytake up to 5 minutes until a GPS localisation can be performed.

Thetimeuntilthefirstlocationisrecognisedmaybereducedbyoptimisedreceiverlocation. Within the first 30minutesafter first locationdetermination, theGPSpositiondatamayhaveahigher

deviation.ThisisconnectedwiththeGPSsignalthatrequirescorrectiondataforhighaccuracy(keyword:Almanach).TheyareoverlaidwiththeGPSsignalandareusuallytransmittedonceevery30minutes.

a) General GPS Localisation („GPS“)ThefollowingcommandrequeststhecurrentGPScoordinatesandreturnstheminanansweringtextmessagewit-houtassessment.Withthiscommand,youneedtoassessthecoordinates,e.g.byenteringthecoordinatesinarouteplanner or on a website with maps.

SincetheGPScoordinatesarereturnedinNMEA-0183format,thesedatamustbeconvertedintodecimalformat to be used by online map providers.

ThesearedatadirectlysentfromtheGPSrecipient.Theyhavenotbeenchanged.Thecommandisasfollows: TEST GPS #1513Return answer example: GX1111.xx Devicename,softwareversion GPS: 5223.53801 N Latitude (ggmm.mmmm) 02112.0730 E Longitude (gggmm.mmmm) ThecoordinatesareindicatedinNMEA-0183format(g=degree,m=minute)

Theanswertothiscommandcanbedelayedbyuptoabout5minutesduetotheGPSsearch.

30

b) Submission of a Web Link with GPS Position („GPSMAP“)A Smartphone with internet connection can be used to display the current position via a link to the website Open-StreetMap.org.Thisdirectlyshowsthecurrentlocation.Thecommandforthisfunctionis: TEST GPSMAP #1513IfthelinkisopenedwithaSmartphone,thecurrentlocationwillbedisplayed.Anexampleforwhatthismaylooklikeisshowninthefigureontheright.

The linked-to OpenStreetMap.org website requires a currentbrowsertodisplayandcontrolthemapmaterial.Therefore,acur-rent Smartphone with an internet connection is needed.

c) Reading Date/Time and Synchronising clock („GPSDATE“)TheclockintheGX111isautomaticallysynchronisedwiththetimedeliveredbytheGPSsignalandthedateduringsystem start. IfnoGPSsignalisavailable,thesystemtimeoftheGPSsignalisunchanged(theclockinstalledintheGX111isnotupdatedandthuscontinuestorununchanged).Inthiscase,youwillreceivetheansweringtextmessage„NoGPSreception!“.ThiscommandmanuallystartsasearchforthecurrenttimeviaGPS: SET GPSDATE #1513ThecurrentdateandtimearereadfromtheGPSsignalandtheinternalclockissynchronised.IfnoGPSisavailable,the clock is not set.TocheckavailabilityoftheGPSsignalandthecontaineddateandtime,usethefollowingcommand: TEST GPSDATE #1513It reads the date and returns it.

31

d) Activate Position Tracking („TRACK“)„Tracking“meansregularsavingofthecurrentposition,includingtimestamp,intheinternalmemory.Thepositionisstoredevery2seconds.Thiscannotbechanged.Thenumberofsavedpointsdependsonthecurrentmemoryutilisation;thecurrentnumbercanonlybedeterminedwiththeTESTcommand.Atalatertime,thevaluescanbesubmittedtoaPCbyUSB.Thecorrespondingprogrammecan be used to track the path over time.64512positionentriesaresavedintheGX111.Ifthenumberofentriesisexceeded,theoldest64entriesaredeletedand overwritten with new data.

Save settings:Usethefollowingcommandtoconfigureandactivatetherecords: SET TRACK [<Name>] #1513Theparameter<Name>isoptionalandservesonlytoassignaninternalnameforrecording(upto10characters).Inthebasicsettings,thenameis„TRACKING“.Ifthecharacterlengthisexceeded,theGX111returnsanerrormessageandtrackingisnotstarted.

If tracking isactivated, theGX111remains in„ONLINE“modeatall times.The„TIMEOUT“settingsnolonger have any effect.

IfnoGPSdatacanbefound,recordingisinterruptedforthisperiod.OncenewGPSdataarereceived,recording continues.

Checking settings:Tocheckthesettingsfortherecordingmode,usethecommand: TEST TRACK #1513Aftersendingthecommand,youwillreceiveananswertextmessage(thetimeisindicatedinUTCtime).Example: GX1111.xx 15.02.2013 20:18:12 Trackdata:58%36000 Track:Name Tracking:onTheinformation„Trackdata:58%36000“saysthatthetrackingmemoryisfilledto58%andthatabout36000trackingsets can still be written.Ifyoureceivethefeedback„Trackdata:100%0“,thetrackingmemoryisfull.Newtrackingdataarewrittenatthestartofthememory,deletingthe64oldestsetsoftrackingdataeach.Trackingdataarethenlost.

32

Stopping recording:Tostoprecordingofthetrackingdata,sendthecommand: RESET TRACK #1513ThetrackingdatashouldbeprimarilydownloadedviaUSB.Optionally,thereistheoperationofemaildispatchaswell.

Emaildispatchrequireshighertechnicalknowledge.Formoredetailedinformation,seethechaptersonthecommands„GPRS“,„SMTP“and„TRACKDATA“.

e) Programming the GPS Zone („GPSZONE“)TheGX111maybeusedforzonemonitoring(„GeoFence“).Afterprogrammingtheapprovedzone,eachtimethezoneborderiscrossed,analarmmessagewiththecurrentGPScoordinateswillbesenttoallsavedphonenumbers.

Ifthezonemonitoringisactivated,theGX111isalwaysin„ONLINE“mode.Thisreducesbatterylifecon-siderably.Therefore,thisfunctionshouldonlybeusedwhensuppliedwithpowerexternallyviaUSB.

Thefollowingcommandsetsthezoneparametersandactivatesthemautomatically: SET GPSZONE <latitude1> <direction> <longitude1> <direction> <latidude2> <direction> <longitude2> <direction> [<ZoneName>] #1513Important prerequisites:• <Latitude1>mustbefurtherNorththan<Latitude2>. Thefollowingmustapply:<Latitude1>largerthan<Latitude2>. The<direction>forthelatitudeisN(North)orS(South).• <Longitude1>mustbefurtherWestthan<Longitude2>. Thefollowingmustapply:<Longitude1>smallerthan<Longitude2>. The<direction>forthelongitudeisE(East)orW(West).• The<ZoneName>isoptional(max.length10characters).

Ifthecharacterlengthisexceeded,theGX111returnsanerrormessageandthevaluesarenotsaved.CreateaGPSzonewithanedgelengthof250maroundtheactualGPSposition: SET GPSZONE #1513Deactivationoftheactivezone;thezoneparametersareretained: SET GPSZONE DISABLE #1513Activationofthedeactivatedzone: SET GPSZONE ENABLE #1513Deletingthezone: RESET GPSZONE #1513Readingthezoneconfiguration: TEST GPSZONE #1513

33

Theformatoflatitudeandlongitudemustbeindicatedinthe„NMEA-0183“format.Thefollowingexampleshowsthedatainputformat: SET GPSZONE 4932.4457 N 01156.5208 E 4932.4101 N 01156.8533 E test #1513

34

12. Email Dispatch of the Tracking DataTheGX111isabletosendthetrackingdatasavedwiththecommandTRACKbyemail.However,thisrequiresadvan-cedknowledgeintheareaofSMTPprotocol,internetarchitecture,emailconfiguration,etc.Problem server timeout, bad data connection, GPRS speed:TheproducthasaGPRSmoduleandthusamaximumuploaddataspeed(fromtheGX111totheInternet)of53.6kbit/s. Evenunderthebestconditions,completeuploadingofthetrackingdatawouldtakeatleast8minutes.AtGSMradiomastchange,inruralareas(weaksignal),withhighnetworkutilisation(conurbations)orotherdifficul-ties,theremaybeinterruptionsoftheemail-serverconnection.Thelongeraconnectiontakes,thehighertheprobabilityofcancellation.Itcannotbepredictedhowlongtheconnec-tion is retained and how high the data rate will be. Therefore,youastheuseroftheGX111mustdecidewhat„Risk“istobetakenforthetransmissionvolume.EachunsuccessfulattemptwillbechargedbytheGSMprovider,nomatteriftheemailwassentsuccessfullyornot.Forthisreason,theareaandthusthedatavolumetobetransferred,ischosenwhensendingthetrackingdata.Thebiggerthedatavolume,thebiggertherisk.Theareainputpermitstransmissionofthememoryinseveralsmallsteps.

Duetothecomplexityofthemanyvariationoptions,thetechnicalsupportforthisareaislimited.OnlyhelpwithconfigurationonthesideoftheGSMmodulecanbeoffered.

Thequestionsofhowthedatarequiredforemail-serverconfigurationaredetermined,howtheemailserveris set and whether the email server even permits an incoming connection can only be answered by the email provider.

Youhavefullcontrolofwheretotransferthedata.Onlytheselecteddatawillbetransferred,onlyatthetimeandonlytotheserverthatyouhaveconfigured.

35

a) Configuration of the SMTP Access Data (SMTP)ThereistheoptiontohavethetrackingdatasentviaSMTP.Forthis,anemailaddress,theSMTPserver,theloginname and the password of the email account must be indicated. SET SMTP <Email adress> <SMTP host> <Port> <Config> <Login> <Password> #1513Email address: max. 30 charactersSMTPhost: max.30charactersPort: 25,465,587Config: 0=Normal,1=SSL,2=EHLO,3=SSL/EHLOLogin name: max. 30 charactersPassword: max. 15 characters

EHLOmeans„ExtendedHELO“andispartoftheSMTPprotocol.SomeserversrequireEHLO.Example: SET SMTP xxxgx111@yahoo.de smtp.mail.yahoo.com 25 1 xxxgx111@yahoo.de Password #1513Thefollowingcommandwillreturnthecurrentconfigurationbytextmessage: TEST SMTP #1513Youwillreceive,e.g.,thefollowingconfirmationtextmessage: GX11101.xx SMTP:smtp.mail.yahoo.de Addr: xxxgx111@yahoo.de Port: 25 Login: xxxgx111@yahoo.de PW:XXX Config:SSL

Thepasswordisnotindicatedinplaintextintheanswer,butasacharacterstring„XXX“.Heresomeexamplesforemailconfiguration:

Yahoo.com Arcor.de GoogleSMTP smtp.mail.yahoo.com mail.arcor.de smtp.gmail.comLogin coresponds to email adress coresponds to email adress wit-

hout the „@arcor.de“coresponds to email adress

Port 25 25 25Config 1 1 1

36

b) Configuration of the GPRS Access Data („GPRS“)Successful connection viaGPRS requires configurationof theaccessdataAPN,usernameandpassword.Thisconfigurationisonlyusedtosendtrackingdataviaemail.

Atthetimeofgenerationoftheseoperatinginstructions,manyGSMprovidersinGermanyhaveadmittedto not requiring any APN server settings and account data.

Youmayneedtoresearchhowthisisimplementedabroadviayourprovider. SET GPRS <APN> [<User name>] [<Password>] #1513APN: Accesspointname,max.30charactersUsername: optional,max.10charactersPassword: optional,max.10characters

Ifoneofthecharacterlengthsisexceeded,theGX111returnsanerrormessageandthevaluesarenotsaved.

Bothoptionalparametersornooptionalparametermustbeindicatedatalltimes!Example: SET GPRS internet.eplus.de eplus eplus #1513Youwillreceive,e.g.,thefollowingconfirmationtextmessage: GX11101.xx APN: internet.eplus.de Login: eplus PW:XXXTestedproviders:Eplus: internet.eplus.de,nousernameorpasswordO2: works without settingsD1: works without settings

Duetothenumberofproviders,itisnotpossibletomakeaprecisestatementontheconfigurationortherequired parameters.

Inquireaboutthis,e.g.,onlinefromyourprovider.

37

c) Transmission of the Tracking Data („TRACKDATA“)ThecommandTRACKDATAonlyworksviatextmessageifSMTPandGPRShavebeensetfirst.Afterreceiptofthiscommand,theGX111willsendanemailviaSMTPserverwiththetrackingdataasanattachedfile.Thesizeofthefilecanbeuptoapprox.3.26MByte.ThetrackingdataarepresentinCSVformatandpreparedforfurtherprocessing,e.g.,inaspreadsheetprogramme(e.g. Microsoft Excel).Thedataarepresentinthetextfileasdescribedbelow:Date,time,latitude,direction,longitude,direction,trackname<linechange>Example: 13.05.2013,16:10:41,01156.6192,E,4932.4173,N,Name

ThetimeisindicatedinUTCtime,theGPSdataareindicatedintheformat„NMEA-0183“,thenamecor-respondstotherespectiveprogrammingbyTRACKcommand

Conversion of tracking data (NMEA) to decimal digits:Latitude: 01156.6192=011degrees,56.6192minutes=011+(56.6192/60)=11.943653degreesLongitude: 4932.4173=49degrees,32.4173minutes=49+(32.4173/60)=49.540288degrees

Command to read the tracking data:Thefollowingcommandindicateswhichareaofthetrackingmemoryistobesentbyemail: TEST TRACKDATA <First entry> <Last entry> #1513First entry: First entry to be read Last entry: Last entry to be read Valuerange: min.1-max.64512Example: TEST TRACKDATA 420 421 #1513Memory:

Basedonthiscount,thecommandwouldreturnthetwomemoryvaluesinthepositions420and421byemail. Anewtrackingentrywouldpushinnewvalues„atthetop“intoposition1,whichwouldpushthelastentry

out at position 64512 and thus delete it.Thecountgenerallystartsatthelatest(newest)trackingpointandcountsbackwardsintothepast.

38

Ifamemoryareathathasnotbeenfilledyetisrequested,anemptyfileisreturned. Important!

Duringthetransmissiontimeoftheemail,theGX111willnotacceptanycommands,notrackingdataaresaved and no alarm situations are recognised.

Command to delete the tracking data:ThefollowingcommanddeletesalltrackingdatainthememoryoftheGX111: RESET TRACKDATA #1513

39

13. System FunctionsThischapterexplainsvariousimportantsystemfunctions.Thebasicsettingsof thesesystem functionsareusuallyalreadyselectedperfectly formostareasofapplication.Therefore,werecommendonlyadjustingtheseparametersintherespectiveapplicationcases.

IftheGX111hasanymalfunctions,reactivatethedefaultsettingsfirst. Beforecontactingourhotline(seechapter1),alwaysensurethattheGX111isinthestandardconfiguration

(factory settings) again.

a) Time between Two Alarm Messages („IDLEALARM“)Incaseofalarm,theGX111willsendanalarmmessage.Fromthistimeonwards,atimewindow(idlewindow)startsforthisinput(sensor,GPS,etc...);duringthistime,nootheralarmcanbetriggered.

ThisreducesthetextmessagecostscausedbyanincorrectlysetconfigurationoftheGX111.Every alarm source has its own idle time window. A value of 120 seconds is set in the factory for the idle time window.Thefollowingcommandisusedtochangethisidlewindow: SET IDLEALARM <Time> #1513Time: 30-3600secondsExample: SET IDLEALARM 240 #1513Theminimumperiodbetweenalarmmessagesisnow240minutes(4minutes).

Inthistimewindow,youwillnotreceiveanynewmessagesonalarmsituationchanges. Valuesbelowthestandardvalueof120secondsshouldonlybeusedfortestpurposeswherepossible.

Changing the alarm value of a sensor will reset „IDLEALARM“ timer and the senor may trigger an alarm again at once.

Example:Theshocksensorisconfiguredwithmaximumsensitivity.The„IDLEALARM“timerwillstartfromthetimeafterwhichallalarm textmessageshavebeensent. If thesensor is triggeredagainwithin the idle timewindow,noalarm istriggered (idle time has not expired yet). Only after the end of the idle time window can another alarm be triggered by the shock sensor.

Thisdoesnotrefer to theothersensors,e.g. the lightsensor.Eachalarmsourcehas itsownidletimewindow!

40

b) Online/Offline Times of GSM („TIMEOUT“)Chapter 7. b) (operating mode) already explained the subject of „ONLINE“ and „OFFLINE“ mode. Thecommand„TIMEOUT“setsthetimesfor„ONLINE“and„OFFLINE“.

Inthecurrenthardware/firmwareversion,theGX111workswithanaccuracyof±3%forthesettime.Thedefaultsettingforthe„ONLINE“modeis15minutes,togiveyouenoughtimetoreact.Thedefaultsettingfor„OFFLINE“ mode is 1425 minutes to save energy.

ThisdefaultsettingspecifiesthattheGX111spends15minutesin„ONLINE“modeeveryday,whileremai-ningin„OFFLINE“modetherestoftheday(15+1425=1440minutes=24h).

IfyouwouldliketobeabletoreachtheGX111moreoftenthan1xperday,orifyouwouldliketohavemoretimetoreacttotheansweroftheGX111,thetimescanbechangedwiththefollowingcommand. SET TIMEOUT <online time> <offline time> #1513„ONLINE“ mode: 5 - 255 minutes„OFFLINE“ mode: 0 - 65536 minutes

Alongertimein„ONLINE“modewillreducetheoperatingdurationoftheGX111.

Resetting online/offline times to the default settingsSend the following command to restore the factory settings: RESET TIMEOUT #1513„ONLINE“ mode: 15 minutes„OFFLINE“ mode: 1425 minutes

Time conduct of the GX111 without a triggering alarm:TheGX111switchesitsmodeintheconfiguredintervals.

online online online

SET TIMEOUT <online> <offline> #1513

offline offline offline

Timeout

41

Time conduct of the GX111 with a triggering alarm:Onlinetime:15minutes,offlinetime:60minutesTheGX111is in„OFFLINE“mode(60minutes).After thealarmwasdetected, theGX111willswitchto„ONLINE“modefor15minutes.Inthese15minutes,thealarmtextmessageissenttoallenteredphonenumbersbeforethedevice waits for the end of the 15 minutes. TheGX111switchesbackto„OFFLINE“modefortheconfigured60minutes.

42

14. ERROR and LED Flashing Sequencesa) „ERR“ LEDThe„ERR“LEDdisplaysdifferenterrormessagesand„Busy“signals.Themessagesareputoutwithaflashingcodeforbetterdifferentiation.Thissequenceisrepeated.

Additionally, thereisthediagnosismodeinwhichthefunctionofthe„ERR“LEDisassumed.Formoreinformation,seechapter10.c)onthecommand„DIAGNOSE“.

„ERR“ LED is not lit• noerrorhasoccurred• GX111isnotsuppliedwithpowerortherechargeablebatteryisflat• Bootingandself-testcompleted„ERR“ LED is always lit• PIN-error• PUK-mustbeentered• ahardwareerrorhasbeenfoundduringtheself-test(connecttheGX111toaPCandchecktheUSB-protocol)„ERR“ LED flashes slowly, LED on for 1 second, off for 1 second• GX111isbooting• Self-testunderway„ERR“ LED flashes quickly 3 times, LED on for 0.25 seconds, off for 0.25 second• Resettingtodefaultsettingsisunderway,flashingpatternisdisplayedbeforebooting„ERR“ LED flashes slowly, LED on for 1.5 seconds, off for 0.5 seconds• Errorwhenloadingtheusersettings• Errorwhenloadingthedefaultsettings„ERR“ LED flashes quickly, LED on for 0.25 seconds, off for 0.25 seconds• Dataarebeingsentviaemail

43

b) „GSM“ LED„GSM“ LED is not lit• TheGX111isnotsuppliedwithpower.• TheGX111isin„OFFLINE“mode.„GSM“ LED flashes quickly, LED on for 0.5 seconds, off for 0.5 seconds• SearchingforGSMnetwork.„GSM“ LED flashes slowly, LED on for 1 second, off for 1 second• TheGX111isloggedontotheGSMnetworkortheGPRSconnectionisactive.

c) „AKKU“ LED„AKKU“ LED is not lit• Therechargeablebatteryisfullychargedornotbeingcharged.„AKKU“ LED is always lit• Therechargeablebatteryischarged.

d) „GPS“ LED„GPS“ LED is not lit• TheGX111isnotsuppliedwithpower.• TheGPSreceiverisoff.• Thepositionwasnotfoundandthetimerforpositionsearchhasexpired.„GPS“ LED flashes slowly, LED on for 1 second, off for 1 second• ScanningfortheGPSposition.„GPS“ LED flashes quickly, LED on for 0.5 seconds, off for 1.5 seconds• TheGPSpositionwasfoundortheGX111isintrackingmode

44

15. Reset to DefaultThefactorysettingsareresetwiththebuttons„RESET“and„S1“.

Important! ThePINoftheGX111isresettothedefaultvalue#1513inthereset. ThePINoftheSIMcardremainsunchanged,however. IfyouhavesettheSIMcard‘sPINtoanyothervaluethan1513,theGX111willnolongerworkafterthe

reset,andyouhavetochangethePINoftheGX111accordingly!ToresettheGX111tothefactorysettingsviathebuttons,proceedasfollows(thismustbedonewithin3seconds):• Keepthebutton„S1“pushed• Brieflypushthebutton„RESET“.• Releasethebutton„S1“again.

If thebutton„S1“ ispushedformorethan3secondsintotal, theGX111willnotberesettothefactorysettings,sinceitisassumedthatyoupushedthebuttonbyaccident.

Aftersuccessfulresettingtofactorysettings,aflashingpatternisoutputviathe„ERR“LED.The„ERR“LEDflashes3timesinquicksequence(0.25secondson,0.25secondspause,etc.).

16. Maintenance and CleaningTheproduct ismaintenance-free foryou.Servicingor repairmustonlybecarriedoutbyaspecialistorspecialistworkshop.Therearenocomponentsonthe insideof theproduct thatneedmaintenancebyyou.This iswhyyoushould never open/disassemble it (apart from the work described in these operating instructions for inserting/changing the rechargeable battery).Adry,softandcleanclothissufficientforcleaningtheoutside.Dustcaneasilyberemovedwithalong-hair,softandcleanbrushandavacuumcleaner.

Neveruseanyaggressivecleaningagents,cleaningalcoholorotherchemicalsolutions,sincethesemaydamage the casing or even impair function.

45

17. Declaration of Conformity (DOC)ConradElectronicSE,Klaus-Conrad-Straße1,D-92240Hirschau,herebydeclaresthatthisproductconformstothe2014/53/EU directive.

Click on the following link to read the full text of the EU declaration of conformity: www.conrad.com/downloads Selectalanguagebyclickingonthecorrespondingflagsymbol,andthenentertheproductordernumber

inthesearchbox.TheEUDeclarationofConformityisavailablefordownloadinPDFformat.

18. Disposala) General Information

Electrical and electronic products must not be disposed of in domestic waste. Dispose of the product according to the relevant statutory regulations at the end of its service life. Remove the inserted rechargeable battery and dispose of it separately from the product.

b) Batteries and Rechargeable BatteriesYouastheenduserarerequiredbylaw(BatteryOrdinance)toreturnallusedbatteries/rechargeablebatteries.Dis-posingoftheminthehouseholdwasteisprohibited!

Batteriesandrechargeablebatteriescontaininghazardoussubstancesaremarkedwiththeadjacentsym-bol to indicate that disposal in the household waste is prohibited.

Thedescriptionsfortherespectiveheavymetalsare:Cd=cadmium,Hg=mercury,Pb=lead(thenamesareindicated on the battery/rechargeable battery e.g. below the rubbish bin symbol shown to the left).

Youmayreturnusedbatteries/rechargeablebatteriesfreeofchargeattheofficialcollectionpointsofyourcommunity,inourstores,orwhereverbatteries/rechargeablebatteriesaresold!Youthusfulfilyourstatutoryobligationsandcontributetotheprotectionoftheenvironment.

46

19. Technical DataOperating voltage ..................................................5V/DCviaUSBCurrent consumption via PC ..................................<500mARequired battery ....................................................LiPo,1500mAh,ratedvoltage3.7VRechargeable battery charging time (min=atthePC) ...................................................Sleep mode min/max 3.5 h / 16 h Trackingmin/max 4.2h/160hRechargeablebatteryruntime(at+22°C) ............+SHOCK/SLOPE 104days +LIGHT 38days +VOICE 24days +GSM+GPStracking 0.5daysAccuracyTIMEOUT ...............................................±3%GSM module ..........................................................GE864-GPSGSM frequency bands ...........................................GSM850(824-894MHz) GSM900(880-960MHz) GSM1800(1710-1880MHz) GSM1900(1850-1990MHz)Transmissionpower...............................................GSM850:1,8W GSM 900: 34 dBm GSM 1800: 31 dBm GSM1900:0,83WGPS chipset ...........................................................TELITGPS sensitivity ......................................................-163dBmMaximum memory slot numbers GPS ...................64512(GPS,Time,Name)GPS tracking interval .............................................2 sGPS data format ....................................................NMEA-0183Vibrationsensor .....................................................Measuringrange-4gto+4g Scanningrate250kHzPosition sensor accuracy .......................................±1%Light sensor wavelengths ......................................380 - 1100 nmAmbient temperature .............................................-4°Cto+55°CAmbient air humidity ..............................................20%to80%rel.humidity,non-condensingDimensions (L x W x H) .........................................77 x 44 x 27 mmWeight ...................................................................Approx. 85 g

47

ThisisapublicationbyConradElectronicSE,Klaus-Conrad-Str.1,D-92240Hirschau(www.conrad.com).All rights including translation reserved. Reproduction by anymethod, e.g. photocopy,microfilming, or the capture inelectronicdataprocessingsystemsrequirethepriorwrittenapprovalbytheeditor.Reprinting,alsoinpart,isprohibited.Thispublicationrepresentthetechnicalstatusatthetimeofprinting.Copyright 2018 by Conrad Electronic SE.

1168681_V5_0618_01_VTP_m_en