Operating instructions for washing machines - miele.sg · Miele. If other parts are used, warranty,...

Operating instructionsfor washing machines

To avoid the risk of accidents or damage to the machine, it is essentialto read these instructions before it is installed and used for the first time.

en-SG M.-Nr. 10 835 960

Caring for the environment

2

Disposal of the packingmaterialThe packaging is designed to protectthe appliance from damage duringtransportation. The packaging materialsused are selected from materials whichare environmentally friendly for disposaland should be recycled.

Recycling the packaging reduces theuse of raw materials in themanufacturing process and alsoreduces the amount of waste in landfillsites.

Disposing of your oldapplianceElectrical and electronic appliancesoften contain valuable materials. Theyalso contain specific materials,compounds and components, whichwere essential for their correct functionand safety. These could be hazardousto human health and to the environmentif disposed of with your domestic wasteor if handled incorrectly. Please do not,therefore, dispose of your old appliancewith your household waste.

Please dispose of it at your localcommunity waste collection / recyclingcentre for electrical and electronicappliances, or contact your dealer orMiele for advice. You are alsoresponsible (by law, depending onterritory) for deleting any personal datathat may be stored on the appliancebeing disposed of. Please ensure thatyour old appliance poses no risk tochildren while being stored prior todisposal.

Contents

3

Caring for the environment .............................................................................. 2

Warning and Safety instructions ..................................................................... 6

Operating the washing machine ...................................................................... 13Control panel ....................................................................................................... 13How the control panel works .............................................................................. 14

Before using for the first time .......................................................................... 16

Washing environmentally and economically .................................................. 18

1. Prepare the laundry....................................................................................... 19

2. Load the washing machine........................................................................... 20

3. Select a programme...................................................................................... 21

4. Add detergent ................................................................................................ 23Detergent dispenser drawer ................................................................................ 23CapDosing........................................................................................................... 24

5. Start the programme..................................................................................... 26

6. End of programme - unload the drum ......................................................... 27

Spinning.............................................................................................................. 28

Delay start .......................................................................................................... 30

Programme chart .............................................................................................. 31

Extra options...................................................................................................... 34Short.................................................................................................................... 34Water plus ........................................................................................................... 34Pre-wash ............................................................................................................. 34Soak .................................................................................................................... 34The following extra options can be selected in addition to the programme: ...... 35

Programme sequence....................................................................................... 36

Changing the programme sequence .............................................................. 38Changing a programme (safety lock) .................................................................. 38Cancelling a programme ..................................................................................... 38Interrupting a programme.................................................................................... 38Adding or removing laundry ................................................................................ 39

Contents

4

Garment care label symbols............................................................................. 40

Detergent ........................................................................................................... 41The correct detergent.......................................................................................... 41Water softeners ................................................................................................... 41Dispensing aids ................................................................................................... 41Fabric conditioner and liquid starch.................................................................... 41Miele recommended detergents ......................................................................... 42Recommended detergents in accordance with Directive (EU) Nr. 1015/2010.... 43

Cleaning and care ............................................................................................. 45Cleaning the external casing and the control panel ............................................ 45Cleaning the detergent dispenser drawer ........................................................... 45Cleaning the drum (Hygiene info) ........................................................................ 47Cleaning the water inlet filters ............................................................................. 47

Problem solving guide ...................................................................................... 48The programme does not start............................................................................ 48The programme is cancelled and a fault indicator light lights up in the control panel.............................................................................................. 49During the programme, a symbol appears in the time display ........................... 50At the end of the programme, an indicator light lights up in the control panel ... 50General problems with the washing machine ..................................................... 51An unsatisfactory wash result ............................................................................. 53The door will not open......................................................................................... 54Opening the door in the event of a blocked drain outlet and/or power cut ........ 55

Service................................................................................................................ 57Contact in the event of a fault ............................................................................. 57Optional accessories........................................................................................... 57Guarantee............................................................................................................ 57

Installation.......................................................................................................... 58Front view ............................................................................................................ 58Rear view............................................................................................................. 59Installation surface .............................................................................................. 60Transporting the washing machine to its installation site.................................... 60Removing the transit bars ................................................................................... 60Re-fitting the transit bars..................................................................................... 62Levelling the machine.......................................................................................... 63

Screwing out and adjusting the feet............................................................... 63Installing under a continuous worktop ........................................................... 64Washer-dryer stack ........................................................................................ 64

Contents

5

The water protection system............................................................................... 65Connection to the water supply .......................................................................... 66Water drainage .................................................................................................... 67Electrical connection .......................................................................................... 68

Technical data.................................................................................................... 69

Consumption data ............................................................................................. 70Note for test institutes ......................................................................................... 70

Programmable functions .................................................................................. 71Choosing and selecting a programmable function ............................................. 71Editing and saving the programmable function .................................................. 72Exit programming level........................................................................................ 72 Keypad tone................................................................................................... 72 Lock code...................................................................................................... 73 Control panel switch-off status .................................................................... 73 Memory ........................................................................................................ 74 Longer pre-wash Cottons ............................................................................ 74 Soak duration ............................................................................................... 74 Gentle action ................................................................................................ 74 Reduce temperature..................................................................................... 75 Water plus..................................................................................................... 75 Water plus level ............................................................................................. 75 Maximum rinse level ..................................................................................... 75 Suds cooling ................................................................................................. 76 Anti-crease ................................................................................................... 76 Backlight brightness dimmed ...................................................................... 76

Optional accessories ........................................................................................ 77Detergent............................................................................................................. 77Specialist detergents........................................................................................... 77Fabric care........................................................................................................... 78Additive ............................................................................................................... 78Machine care....................................................................................................... 78

Warning and Safety instructions

6

This washing machine complies with all current local and nationalsafety requirements. However, inappropriate use can lead topersonal injury and damage to property.

Read the operating instructions carefully before using the washingmachine. They contain important information on safety,installation, use and maintenance. This prevents both personalinjury and damage to the washing machine.

In accordance with standard IEC 60335-1, Miele expressly andstrongly advises that you read and follow the instructions in thechapter on installing the washing machine as well as the safetyinstructions and warnings.

Miele cannot be held liable for damage caused by non-compliancewith these instructions.

Keep these operating instructions in a safe place and pass themon to any future owner.

Correct application

This washing machine is intended for use in domestic householdsand similar working and residential environments.

The washing machine is not intended for outdoor use.

It must be used only as a domestic appliance to wash items whichare specified by the manufacturer as being washable on the washcare label. Miele cannot be held liable for damage resulting fromincorrect or improper use or operation.


7

The washing machine can only be used by people with reducedphysical, sensory or mental capabilities, or lack of experience orknowledge, if they are supervised whilst using it or have been shownhow to use it safely and recognise and understand theconsequences of incorrect operation.

Safety with children

Children under 8 years of age must be kept away from thewashing machine unless they are constantly supervised.

Children 8 years and older may only use the washing machineunsupervised if they have been shown how to use it safely andrecognise and understand the consequences of incorrect operation.

Children must not be allowed to clean or maintain the washingmachine unsupervised.

Please supervise children in the vicinity of the washing machineand do not let them play with it.

Technical safety

Please observe the instructions in “Installation” and “Technicaldata”.

Before setting up the washing machine, check it for any externallyvisible damage. Do not install or use a damaged machine.


8

Before connecting the washing machine, ensure that theconnection data on the data plate (fuse rating, voltage andfrequency) match the mains electricity supply. If in any doubt,consult a qualified electrician.

Reliable and safe operation of this washing machine can only beassured if it has been connected to the mains electricity supply.

The electrical safety of this washing machine can only beguaranteed when correctly earthed. It is essential that this standard safety requirement is met. If in anydoubt, please have the wiring system of the building tested by aqualified electrician. Miele cannot be held liable for the consequences of an inadequateearthing system (e.g. electric shock).

Do not connect the washing machine to the mains electricitysupply by a multi-socket adapter, extension lead or similar. These donot guarantee the required safety of the machine (fire hazard due tothe risk of overheating).

Faulty components must only be replaced by genuine Mieleoriginal spare parts. Only when these parts are fitted can Mieleguarantee the safety standards of the machine.

The electrical socket must be easily accessible after installation sothat the machine can be disconnected from the electricity supply ifnecessary.


9

Unauthorised repairs could result in unforeseen dangers for theuser, for which the manufacturer cannot accept liability. Repairsshould only be undertaken by a Miele authorised service technician,otherwise any subsequent damage will not be covered by thewarranty.

If the electrical connection cable is faulty it must only be replacedby a Miele authorised service technician to protect the user fromdanger.

The machine must be isolated from the electricity supply whencleaning and maintaining the machine and in the event of a fault.

The machine must only be connected to the on-site water supplyusing a new hose kit. Old hose kits must not be re-used. Check thecondition of the hoses regularly so that you can replace them ingood time and avoid the risk of any water damage.

The water flow pressure must be at least 100 kPa and should notexceed 1000 kPa.

In areas which may be subject to infestation by cockroaches orother vermin, pay particular attention to keeping the machine and itssurroundings in a clean condition at all times. Any damage whichmay be caused by cockroaches or other vermin will not be coveredby the warranty.

The machine must not be used in a non-stationary location (e.g.on a ship).

Do not make any alterations to the machine, unless authorised todo so by Miele.


10

Correct use

Do not install the washing machine in a room where there is a riskof frost. Frozen hoses may burst or split. The reliability of theelectronic control unit may be impaired at temperatures belowfreezing point.

Before using the machine for the first time, check that the transitbars at the rear of the machine have been removed (see “Installation- Removing the transit bars”). During spinning, a transit bar which isstill in place may result in damage to both the machine and adjacentfurniture or appliances.

Turn off the stopcock if the machine is to be left for any length oftime (e.g. holiday), especially if there is no floor drain (gully) in theimmediate vicinity.

Flooding danger. If hooking the drain hose into a wash basin, check that the water candrain off quickly enough to prevent the sink from overflowing. Makesure the drain hose is secure, so that the force of the water flowingout of the hose does not dislodge it.

Take care to ensure that foreign objects (e.g. nails, pins, coins,paper clips) do not find their way into the machine with the laundry.These may damage components of the machine (e.g. sudscontainer, drum), which in turn can result in damage to the laundry.

The maximum load for this washing machine is 8 kg (dry weight).See the “Programme chart” for the maximum recommended loadsfor individual programmes.


11

If the correct amount of detergent is dispensed, the machineshould not need to be descaled. If, however, you do wish to descaleit, only use a proprietary natural citric acid based descaling agent.Miele recommends using Miele descaling agent which is available toorder from your Miele dealer. Strictly observe the instructions on thepackaging.

Textiles which have been pre-treated in solvent based cleaningagents must be thoroughly rinsed in clean water before beingwashed in the machine.

Do not use solvent based cleaning agents, e.g. those containingbenzine, in this machine, as this may result in damage to componentparts and create toxic fumes. Such agents also pose a fire andexplosion hazard.

Do not use solvent based cleaning agents, e.g. those containingbenzine, to clean the surfaces of the machine. They can causedamage to plastic surfaces.

Only use dyes specified by the manufacturer as being suitable foruse in a domestic washing machine. Always observe themanufacturer's instructions carefully.

Colour run and dye removers contain sulphur compounds whichcan cause damage such as corrosion. Do not use these products inthis machine.

If detergent comes into contact with the eyes, rinse themthoroughly with lukewarm water immediately. If swallowed, seekmedical assistance immediately and retain the packaging or label forreference. Those with skin problems or sensitive skin should avoidtheir skin coming into contact with detergent.


12

Accessories

Accessory parts may only be fitted when expressly approved byMiele. If other parts are used, warranty, performance and productliability claims will be invalidated.

A Miele tumble dryer can be stacked on top of a Miele washingmachine using the appropriate stacking kit (available as an optionalaccessory). Please make sure you order the correct one for the Mielewashing machine and Miele tumble dryer.

If installing the machine on a Miele plinth, (available as an optionalaccessory, depending on country), please make sure you order thecorrect one for this washing machine.

Miele cannot be held liable for damage caused by non-compliancewith these Warning and Safety instructions.

Operating the washing machine

13

Control panel

a Control panel

b Sensor controls – temperaturefor selecting the temperature.

c Sensor controls – spin speedfor selecting the spin speed.

d Sensor controls – extrasvarious options can be added to thewash programmes.

e Indicator lights light up when necessary

f Sensor controls – CapDosing

g Time displayfor the programme duration

h Sensor controls for the delay start function

i Sensor control – Start/Stopfor the programme start/cancellation

j Optical interfacefor service technicians

k Programme selectorfor programme selection and forswitching the machine off. Selectinga programme switches the washingmachine on, and turning theprogramme selector to switchesthe machine off.


14

How the control panel works

The , , , , and sensorsreact to fingertip contact. Selection ispossible as long as the respectivesensor is illuminated.

If a sensor is brightly lit, this means:currently selected

If a sensor is dimly lit, this means:selection possible

and sensors for temperatureand spin speed

After selecting a wash programme withthe programme selector, therecommended temperature (in °C) andspin speed (in rpm) light up brightly.

Selectable temperatures and spinspeeds light up dimly.

Sensor controls for extras

You can select extra options toaugment the wash programmes.

If a wash programme has beenselected, the sensor controls for thepossible extras light up dimly.

Indicator lights

– lights up if there are faults with thewater inlet and drainage

– lights up if excess detergent wasused

– lights up as a reminder about hygieneinformation

– flashes for as long as it is possible toadd laundrylights up when the door of thewashing machine is locked

CapDosing

The CapDosing sensors are used foractivating cap dosing.

– Fabric care (e.g. fabric conditioner,proofing agent)

– Additives (e.g. detergent enhancers)

– Detergent (for the main wash only)


15

Time display

After the programme has started, theprogramme duration will appear in thedisplay in hours and minutes.

If delay start has been selected, theprogramme duration will appear at theend of the delay start time.

Sensor controls

– After touching the sensor, a laterstart time for the programme (delaystart) can be selected. Onceselected, lights up brightly.

– The duration of the delay start periodis selected by touching the or sensor.

The delay start time selected willappear in the time display.

After the programme has started, thedelay start time will begin to countdown.

Once the delay start time has elapsed,the programme begins and theestimated programme duration appearsin the time display.

Start/Stop sensor control

Touching the Start/Stop sensor startsthe selected programme or cancels aprogramme that has already beenstarted. The sensor flashes slowly assoon as it is possible for a programmeto be started and then lights upconstantly after the programme hasstarted.

Before using for the first time

16

Damage resulting from incorrectinstallation and connection.Installing and connecting thewashing machine incorrectly willcause serious property damage.See “Installation”.

Protective foil and stickersremoval Remove:

– The protective foil from the door

– Any stickers from the front and the lid

Please do not remove any labels(e.g. the data plate) which are visiblewhen you open the door.

Remove the drain hose elbowfrom the drumAn elbow piece for the drain hose isstored in the drum.

Reach under the door grip and pullthe door open.

Remove the elbow piece.

Shut the door with a gentle swing.

This washing machine has undergonea complete functional test at thefactory and there will be some residualwater in the drum from this process.

For safety reasons, spinning is notpossible until the machine has beenprepared for using for the first time. Toactivate the spinning function you mustrun a wash programme without laundryand without detergent.

Using detergent could result in anexcessive build-up of foam.

This also activates the ball valve. Theball valve prevents detergent escapingfrom the suds container into the sumpduring a wash programme, thus makingmaximum use of the detergent.

Before using for the first time

17

Running the first programme Open the stopcock.

Turn the programme selector toCottons.

The washing machine is now switchedon and in the control panel, thetemperature 60 °C lights up.

Touch the Start/Stop sensor.

The programme will start and the symbol lights up in the control panel.

After 10 minutes, the indicators dimand the Start/Stop sensor startsflashing.

At the end of the programme

At the end of the programme, the Anti-crease function is switched on. The symbol lights up in the control panel;: appears in the time display andthe drum occasionally rotates.


The door will unlock.


Tip: Leave the door slightly open toallow the drum to dry.

When the programme has ended,turn the programme selector to .

The washing machine is switched offand is now ready for use.

Energy savings

– Ten minutes after the beginning of theanti-crease phase, the indicators dimand the Start/Stop sensor startsflashing.

– Fifteen minutes after completion ofthe anti-crease phase, the washingmachine is completely switched offand the door lock lifted.

Washing environmentally and economically

18

Energy and water consumption

– Water consumption and energyusage are determined by the size ofthe load.To make the most of your machine,load the maximum dry load for theprogramme you are using.

– When smaller amounts of laundry arewashed, the automatic load controlwill reduce the amount of water andenergy used.

– Use the Express 20 programme forsmall, lightly soiled loads.

– Modern detergents make it possibleto wash at lower temperatures (e.g.20 °C). Washing using lowertemperature settings will save energy.

– To maintain the hygiene of themachine, carry out a hot wash (above60 °C) at regular intervals. The indicator will light to remind you tocarry out a hot wash.

Detergent

– Do not exceed the amounts ofdetergent recommended by themanufacturer on the packaging.

– Adjust the dosage to the degree ofsoiling of the laundry.

– Reduce the amount of detergent withsmaller loads (approx. ⅓ less thanthe amount recommended can beused when washing a half load).

Choosing the correct extra option(Short, Soak, Pre-wash)

Select:

– A wash programme together with theShort extra option for light to normalsoiling where there are no obviousmarks.

– A wash programme without any extraoptions for normal to heavy soilingwith visible staining.

– A wash programme together with theSoak extra option for heavily soiledlaundry.

– The Pre-wash extra option for laundrywith large amounts of dirt (e.g. dust,sand).

When drying with a tumble dryer

Selecting the highest possible spinspeed for the wash programme willsave energy when drying in a tumbledryer afterwards.

1. Prepare the laundry

19

Empty all pockets.

Damage due to foreign objects.Nails, coins, paper clips, and so oncan cause damage to garments andcomponents in the machine.Check the laundry before washingand remove any foreign objects.

Sort the laundry

Sort the laundry by colour and bycare label. Most garments have atextile care label in the collar or sideseam.

Tip: Dark textiles often contain excessdye and should be washed separatelyseveral times before being included in amixed load. Always wash whites andcoloureds separately.

Pre-treating stains

Badly soiled areas and stains shouldbe cleaned as soon as possible,preferably whilst still fresh. Spillagesshould be carefully dabbed off usinga soft, colourfast cloth. Do not rub.

Tip: Stains (e.g. blood, egg, coffee, tea)can be pre-treated using some handytricks which can be found in the Mieleguide to laundry care.

Damage due to solvent-basedcleaning agentsCleaning agents containing benzine,stain remover, etc., can damageplastic parts.When pre-treating textiles, make surethat any plastic parts (e.g. buttons)do not come into contact withcleaning agent.

Risk of explosion due to solvent-based cleaning agents.When using solvent-based cleaningagents, an explosive mixture maydevelop.Never use solvent-based cleaningagents in the washing machine.

General tips

– Curtains: Remove lead weights firstor place in a laundry bag.

– Underwiring and collar stiffeners: Anyloose wiring in bras, shirt collarstiffeners, etc. should be removed orsewn in.

– Close any zips, attach velcrofasteners, fasten hooks and eyes etc.before washing.

– Fasten duvet covers, pillow casesetc. to prevent small items from beingrolled up inside them.

Do not wash any items in this washingmachine which are specified by themanufacturer as not washable on thecare label ( symbol).

2. Load the washing machine

20

Open the door


Check the drum for pets or foreignobjects before loading it withlaundry.

The most efficient use of energy andwater is achieved when a full load iswashed. However, do not overload asthis reduces cleaning efficiency andcauses creases.

Unfold the laundry and load looselyinto the drum.

Mixing both large and small itemsgives better wash results and alsohelps distribute the load evenly duringspinning.

Tip: Please note the maximum load fordifferent wash programmes.

Close the door

Make sure that no items are caughtbetween the door and the seal.

Shut the door with a gentle swing.

3. Select a programme

21

Programme selectionThe washing machine is switched on byturning the programme selector to awash programme.

Turn the programme selector to therequired programme.

The likely wash time is shown in thetime display and the pre-settemperature and spin speed light up inthe control panel.

Selecting a temperature and spinspeed

The wash programme’s presettemperature and spin speed light upbrightly. The choice of availabletemperatures and spin speeds for thewash programme light up dimmed.

The temperatures reached inside thewashing machine might not be thesame as the temperatures selected.Perfect wash results are achievedthrough a combination of energy useand wash duration.

Touch the sensor for the desiredtemperature. It will then light upbrightly.

Touch the sensor for the desired spinspeed. It will then light up brightly.

3. Select a programme

22

Selecting Extras

The selection of extras available forthe wash programme lights up dimly.

Touch the sensor for the extra youwant. It then lights up brightly.

Tip: You can select multiple extras for awash programme.

Please refer to “Extras” for moreinformation.

4. Add detergent

23

Detergent dispenser drawerAny detergent suitable for automaticfront loading washing machines can beused. Please observe the instructionsfor use and dosage on the detergentpackaging.

Tips on dosing

Adjust the detergent dosage to the levelof soiling of the laundry and the size ofthe load. Reduce the amount ofdetergent with smaller loads (e.g.reduce the amount of detergent by ⅓when washing a half load).

Too little detergent:

– Results in laundry not being cleanedproperly and may cause it to becomegrey and hard to the touch over time.

– Can lead to a build-up of mould inthe washing machine.

– Results in grease not beingcompletely removed from thelaundry.

– Can lead to limescale deposits on theheater elements.

Too much detergent

– Causes poor wash, rinse, and spinresults.

– Causes higher water consumption asan extra rinse cycle is automaticallyactivated.

– Is a greater burden on theenvironment.

Adding detergent

Pull out the detergent drawer and adddetergent to the compartments.

Detergent for the pre-wash

Detergent for the main wash andsoaking

Fabric softener, liquid starch, orcapsules

4. Add detergent

24

CapDosingThree different types of capsule areavailable:

= Fabric care (e.g. fabricconditioner, proofing agent)

= Additives (e.g. detergentenhancer)

= Detergent (for the main washonly)

Each capsule contains the correctamount for one wash cycle.

Caps are available to order from Mieleor from the Miele online shop (see theend of this booklet for contact details).

Capsules pose a health risk.The ingredients of capsules can behazardous to health if they areswallowed or come into contact withskin.Keep capsules out of the reach ofchildren.

Activating CapDosing Touch the sensor for the capsule you

want to use.

Sensor control Capsule

for

for

for

Inserting a capsule Open the detergent dispenser drawer.

Open the lid of the /compartment.

Press the capsule in firmly.

https://www.miele.co.uk/domestic/shop-2151.htm

4. Add detergent

25

Close the lid and press it firmly shut.

Close the detergent dispenserdrawer.

The capsule is opened by the act ofinserting it in the detergent dispenserdrawer. The contents can run out ofthe capsule if you then remove itfrom the drawer before it is used.Dispose of opened capsules.

The wash programme will dispense thecontents of the capsule at the correcttime.

Water intake to the compartmentis solely via the capsule.Do not add any additional fabricconditioner to the compartment.

Remove the empty capsule at theend of the programme.

For technical reasons a small amountof water will remain in the capsule.

Switching off/changingCapDosing In order to switch off CapDosing,

touch the brightly lit sensor.

In order to change CapDosing, touchone of the other capsule sensors.

5. Start the programme

26

Starting a programme Touch the flashing Start/Stop sensor.

The door will lock and the programmewill start.

– As long as the symbol is flashingin the control panel you can addlaundry.

– When the symbol lights upconstantly, the door is locked untilthe end of the programme.

If a delay start time has been selected,then this will count down in the timedisplay. At the end of the delay starttime or immediately after theprogramme has started the programmeduration will appear in the time display.

Energy savings

After 10 minutes, the indicators dim.The Start/Stop sensor flashes slowly.

To reactivate the indicators:

Touch the Start/Stop sensor (thisdoes not have any effect on a runningprogramme).

6. End of programme - unload the drum

27

End of programmeThe time display shows 0:00. The symbol will remain lit up in the controlpanel. The door is locked in the anti-crease phase.


The door will unlock and the symbol appears in the control panel.

Pull open the door.

Remove the laundry.

Energy savings

– Ten minutes after the beginning of theanti-crease phase, the indicators dimand the Start/Stop sensor startsflashing.

– Fifteen minutes after completion ofthe anti-crease phase, the washingmachine is completely switched offand the door lock lifted.

Items left in the drum could discolourother items in the next wash orbecome discoloured themselves.Remove all items from the drum.

Check the folds in the door seal forany small articles, e.g. buttons, whichmight be lodged there.

Tip: Leave the door slightly open toallow the drum to dry.

Turn the programme selector to the position. This switches the washingmachine off.

If applicable, remove the usedcapsule from the detergentdispensing drawer.

Tip: Leave the detergent dispenserdrawer slightly open to allow it to dry.

Spinning

28

Final spin speed

Programme rpm

Cottons 1400

Cottons 1400

Minimum iron 1200

Delicates 900

Woollens 1200*

Shirts 900

Express 20 1200

Dark garments / Denim 1200

Outerwear 900

Proofing 1200

Drain / Spin 1400

Separate rinse/Starch 1200

Final spin speed in theprogrammeWhen a programme is selected, thesensor for the optimum spin speed forthat programme will be brightly lit up inthe control panel. For programmesmarked with a * in the chart, theoptimum spin speed is not themaximum spin speed.

You can reduce the final spin speed.

However, you cannot select a final spinspeed higher than that shown in thechart.

Rinse and interim spinThere is a spin after the main wash andbetween the rinses. A reduction in thefinal spin speed will also reduce theinterim spin speed. If a spin speed ofless than 700 rpm is selected for theCottons programme, an additional rinseis introduced.

Spinning

29

To omit the final spin (Rinsehold) Touch the sensor (rinse hold).

The laundry is not spun after the finalrinse and remains in the final rinsewater. This helps prevent creasing if thelaundry is not going to be removed fromthe drum immediately after the end ofthe programme.

After the end of a programme

The sensor for the optimum spinspeed lights up in the control panel.You can change the spin speed. TheStart/Stop sensor lights up, flashing.

Start the final spin:touch the flashing Start/Stop sensoronce.

The final spin is carried out.

End the programme:touch the flashing Start/Stop sensortwice.

The water will drain away.

To omit rinse and interim spinand the final spin Touch the sensor.

After the last rinse, the water will bepumped away and the anti-creasephase will switch in.

In some programmes an additional rinseis introduced with this setting.

Delay start

30

With Delay start you can choose whenyou want the programme to start. Youcan delay the start of the programme by30 minutes up to a maximum of 24hours, allowing you to make use ofnight-time economy electricity rates, forexample.

Select delay start

Delay start cannot be selected withDrain/Spin or Proofing.

Select the programme required.

Touch the sensor.

The sensor lights up brightly.

Touch the or sensor repeatedlyuntil the required delayed start timeappears in the time display.

– For less than 10 hours, the delay starttime changes in increments of30 minutes

– For more than 10 hours, the delaystart time changes in increments ofone hour

To begin delay start

Touch the flashing Start/Stop sensor.

The delay start process starts andcounts down in the time display.

To alter delay start


The delay start process stops and the symbol lights up in the control panel.

Touch the or sensor repeatedlyuntil the required delayed start timeappears in the time display.

Touch the flashing Start/Stop sensor.

To cancel a delay start that hasalready started


The delay start process stops and the symbol lights up in the control panel.

Touch the brightly lit sensor.

The delay start period is deleted andthe sensor switches off. Theprogramme duration appears in thetime display.

Touch the flashing Start/Stop sensorin order to start the wash programme.

Programme chart

31

Cottons 60 °C/40 °C Max. load 8.0 kg

Use for Normally soiled cotton garments.

Note – These settings are the most efficient in terms of energy and waterconsumption for washing cottons.

– At 60 °C, the actual wash temperature reached will be lower than60 °C, although the wash performance is the same as with theCottons 60 °C programme.

Note for test institutes:

The test programme conforms to EN 60456.

Note for test institutes:

The test programme conforms to EN 60456.

Cottons Cold to 90 °C Max. load 8.0 kg

Use for Cotton, linen or mixed fibre fabric, e.g. table linen, towelling,underwear, T-shirts etc.

Note The wash temperatures 60 °C/40 °C differentiate themselves fromthe programme Cottons 60 °C/40 °C by:

– Shorter programme durations

– Longer temperature holding times

– Higher energy consumption

Where particularly high levels of hygiene are required please select atemperature of 60 °C or higher.

Minimum iron Cold to 60 °C Max. load 3.5 kg

Use for Synthetic and mixed fibre textiles as well as easy care cotton

Note Reduce the spin speed for fabric that creases easily.

Programme chart

32

Delicates Cold to 40 °C Max. load 2.0 kg

Use for Delicate garments made from synthetic fibre, mixed fibre, rayon andviscose.

Curtains, including net curtains, specified as machine-washable bythe manufacturer.

Notes – Dust in curtains usually makes a programme with pre-washadvisable.

– Deselect the spin for items which crease easily.

Woollens Cold to 40 °C Max. load 2.0 kg

Use for Machine-washable or hand-washable wool or wool blend fabric. Ifthe care label does not specify a temperature, wash using the coldsetting.

Note Reduce the spin speed for items which crease easily.

Shirts Cold to 60 °C Max. load 2.0 kg

Use for Shirts and blouses made of cotton and mixed fibre

Note – Pre-treat soiled cuffs and collars if necessary.

– Wash silk shirts and blouses in the Delicates programme.

Express 20 Cold to 40 °C Max. load 3.5 kg

Use for Cotton garments that have hardly been worn or are only very lightlysoiled

Note The Short option is activated automatically.

Dark garments / Denim Cold to 60 °C Max. load 3.0 kg

Use for Black and dark items made of cotton, mixed fibre or denim.

Notes – Wash inside out.

– Denim often contains excess dye and may run during the first fewwashes. Wash light and dark coloured items separately.

Programme chart

33

Outerwear Cold to 40 °C Max. load 2.5 kg

Use for Performance outerwear (e.g. jackets and trousers) made frommembrane fabric such as Gore-Tex®, SYMPATEX®,WINDSTOPPER® etc.

Notes – Zip up or close jackets before washing.

– Do not use fabric conditioner.

– If wished, these garments can also be re-proofed using theProofing programme. Proofing should not be done every time thegarment is washed.

Proofing 40 °C Max. load 2.5 kg

Use for Treating microfibre fabric, skiwear and table linen made from mainlysynthetic fibres to provide a water and dirt resistant finish.

Notes – The items should be freshly laundered and spun or dried beforeproofing.

– For best results, the items should be heat-treated afterwards eitherin a tumble dryer or by ironing.

Drain / Spin –

Notes – Drain only: Select for the spin speed.

– Make sure you select the appropriate spin speed.

Separate rinse/Starch Max. load 8.0 kg

Use for – Rinsing handwashed items

– Starching table cloths, serviettes and workwear

Note – Reduce the spin speed for items which crease easily.

– The laundry should be washed but not treated with fabricconditioner.

– Items will be rinsed very effectively using two rinse cycles byactivating the extra Water plus option.

Extra options

34

You can use the extra options buttonsto augment the wash programmes.

Extras are selected and deselectedusing the relevant sensors on thecontrol panel.

Touch the sensor for the extra youwant.

The relevant sensor will light up brightly.

Not all the extra options are suitable foruse with every programme.

An extra that is not permitted for thewash programme is not lit dimly andcannot be activated by touch.

ShortUse this option for light soiling with novisible staining.

The wash duration is reduced.

Water plusThe water level in the wash and rinsestages is increased and a second rinseis carried out in the “Separate rinse /Starch” programme.

You can select other functions for theWater plus sensor. These are describedin “Programmable functions”.

Pre-washFor laundry with large amounts of dirt,e.g. dust and sand.

SoakFor heavily soiled and stained itemswith protein stains.

– A duration of between 30 minutesand 2 hours can be programmed in30 minute increments for the soakprocess.

– The factory default setting is30 minutes.

See “Programmable functions - Soak”for instructions on how to programme adifferent soak period.

Extra options

35

The following extra options can be selected in addition to theprogramme:None of the extras can be selected with programmes which are not listed in thechart below.

Sho

rt

Wat

er p

lus

Pre

-was

h

Soa

k

Cottons X X X X

Cottons X X X X

Minimum iron X X X X

Delicates X X X X

Shirts X X X X

Express 20 X1) – – –

Dark garments/Denim X X X X

Outerwear X X X X

Separate rinse/Starch – X – –

X = can be selected 1) = can be deselected

– = cannot be selected

Programme sequence

36

Main wash Rinses Spinning

Waterlevel

Washrhythm

Waterlevel

Rinses

Cottons 2-52)3)

Cottons 2-51)2)3)

Minimum iron 2-42)3)

Delicates 2-42)3)

Woollens 2

Shirts 3-43)

Express 20 1

Dark garments / Denim 3-52)3)

Outerwear 3-43)

Proofing – 1

Drain / Spin – – – –

Separate rinse / Starch 0-15)

Please see the next page for a description of the symbols.

Programme sequence

37

= Low water level

= Medium water level

= High water level

= Intensive rhythm

= Normal rhythm

= Sensitive rhythm

= Ultra sensitive rhythm

= Handwash rhythm

= Carried out

– = Not carried out

The washing machine has fullyelectronic controls with automatic loadrecognition. It takes in the right amountof water required for the programmedepending on the amount of laundryand its absorbency rate.

The programme sequences shown inthe chart are based on the standardprogramme with a full load.

Special features in theprogramme sequenceAnti-crease:at the end of the programme the drumcontinues to turn at intervals for up to30 minutes to help prevent creasing.Exception: there is no anti-creasephase in the Woollens programme.The door can be opened at any timeduring the anti-crease phase.1) If a temperature of 60 °C or higher is

selected, two rinses are carried out. Ifa temperature of less than 60 °C isselected, three rinses are carried out.

2) An additional rinse is carried out if:

– there is too much foam in the drum

– a spin speed lower than 700 rpm hasbeen selected

3) An additional rinse is carried out if:

– Water plus has been selected and theoptions or have been activatedin Programmable functions.

5) An additional rinse is carried out if:the Water plus option is selected.

Changing the programme sequence

38

Changing a programme (safetylock)A programme, temperature, spin speedor selected option cannot be changedonce the machine has beensuccessfully started. This is to preventthe operation of the machine beingtampered with (by a child, for example).

Cancelling a programmeYou can cancel a wash programme atany time after it has started.

Touch and hold the Start/Stop sensoruntil the time display switches to:.

The water will be pumped away. Assoon as the symbol in the controlpanel goes out, the programme hasbeen cancelled.

Open the door.

Selecting a different programme aftercancelling the programme

Close the door.

Check that there is still detergent inthe dispenser drawer. Add moredetergent if necessary.

Turn the programme selector to theprogramme you want and start it bypressing the Start/Stop sensor.

Removing laundry after cancellingthe programme

If you want to remove the laundry whenit is dripping wet:

Open the door.

Remove the laundry.

If you want to remove the laundry afterit has been spun (damp):

Open the door.

Close the door.

Turn the programme selector toDrain/Spin.

Tip: Select an appropriate spin speed.

Interrupting a programme Turn the programme selector to the

position.

The washing machine switches off.

To continue: turn the programmeselector to the position of the washprogramme that was started.

Tip: If appears in the time display,the programme selector is in theincorrect position.

Changing the programme sequence

39

Adding or removing laundry

You can add or remove laundry at thestart of a wash programme as long asthe symbol is flashing in the controlpanel.

Briefly touch the Start/Stop sensor.

The programme will stop and the doorwill unlock.

Pull open the door.

Add or remove items.

Close the door.


The programme will continue.

Garment care label symbols

40

Washing

The figure quoted in the bucket is themaximum temperature the garmentcan be washed at. The number ofbars under the symbol indicates thelevel of agitation permitted.

No bar under the symbol:= normal agitation

One bar under the symbol:= reduced agitation

Two bars under the symbol:= much reduced agitation

Hand wash (if no temperature isspecified, use the lowesttemperature or cold)

Do not wash

Programme selection examples

Programme Garment care labelsymbols

Cottons

Minimum iron

Delicates

Woollens

Express 20

Drying

The number of dots indicates thedrying temperature

Normal temperature

Low temperature

Do not tumble dry

Ironing

The number of dots indicates theironing temperature

Hot iron (max. sole plate temp.approx. 200 °C)

Medium hot iron (max. soleplate temp. approx. 150 °C)

Cool iron (max. sole plate temp.approx. 110 °C).

Do not steam iron garmentscarrying this symbol as thiscould cause irreversibledamage.

Do not iron

Professional cleaning

Dry clean only. The lettersindicate the type of cleaningagent required.

Professional Wet Clean only

Do not dry clean

Bleaching

Any oxidising bleaching agentcan be used

Only use an oxygen basedbleach or a non-chlorine bleach

Do not bleach

Detergent

41

The correct detergentAll detergents produced for automaticwashing machines are suitable. Followthe manufacturer's instructions anddosage recommendations on thepackaging.

For users in Asia:please use a low foaming detergentsuitable for use in front-loadingmachines

The right amount to dispensewill depend on the following:– the soiling level of the load

– the quantity of the laundry

– the water hardness level.Check with your local water supplierif you do not know the hardness levelin your area.

Water softenersA water softener can be used to cutdown on the use of detergents in areaswith water hardness levels II and III.Dispense according to the amountspecified on the packaging. First adddetergent and then the water softener.

You can then use the recommendedamount of detergent for water hardnesslevel I.

Water hardness levels

Hardnessscale

Hardness levelin mmol/l

German scale°d

I (soft) 0 – 1.5 0 – 8.4

II (medium) 1.5 – 2.5 8.4 – 14

III (hard) above 2.5 above 14

Dispensing aidsUse dispensing aids, (e.g. balls) if theseare supplied with the detergent,particularly when using liquid detergent.

Refill packs of detergentWhen purchasing detergent buy refillpacks wherever possible. This helpsreduce the amount of waste packaging.

Fabric conditioner and liquidstarchFabric conditioner makes garments soft to handle andhelps prevent static cling when tumbledrying.

Starch stiffens and gives body to items oflaundry, e.g. shirts, tablecloths and bedlinen.

Detergent

42

Miele recommended detergentsMiele detergents and care products have been specially designed for Mielewashing machines. They are available to order via the internet at www.miele.co.ukor from Miele.

MieleUltraWhite

MieleUltraColor

MieleCap

MieleCap

MieleCap

Cottons – Cottons – Minimum iron – – Delicates – , , –

Woollens – – , – –

Shirts – Express 20 – – –

Dark garments /Denim

– – –

Outerwear – – – –

Proofing – – – –

Separate rinse /Starch

–/– –/– –/– /– –/–

Recommended Sport SilkCare

– Not recommended Down Fabric conditioner

Outdoor Reproofing

WoolCare Booster

https://www.miele.co.uk

Detergent

43

Recommended detergents in accordance with Directive(EU) Nr. 1015/2010The recommendations apply to the temperature ranges given in the Programmechart.

Universal Coloureds Delicates andwoollens

Specialist

detergent

Cottons – –

Cottons – –

Minimum iron – – –

Delicates – – –

Woollens – –

Shirts – –

Express 20 – 1) – –

Dark garments / Denim – 1) –

Outerwear – –

Recommended 1) Liquid detergent

– Not recommended 2) Powder detergent

Detergent

44

Dispensing fabric conditionerand liquid starch at the end ofthe programme

Add the fabric conditioner or liquidstarch to the compartment orinsert the appropriate capsule. Donot exceed the maximum levelmark.

The agent will be automaticallydispensed in the last rinse. At the endof the programme a small amount ofwater will remain in the compartment.

Starch can make the siphon tubesticky.If starching frequently, thoroughlyclean the dispenser compartment,especially the siphon tube regularly.

Adding fabric conditioner or liquidstarch separately

Prepare the starch in accordance withthe manufacturer's instructions on thepackaging.

Tip: When adding fabric softener,activate the Water plus extra.

Add fabric conditioner to the compartment or insert theappropriate capsule.

Add liquid starch to the compartment and powder or viscousstarch to the compartment.

Select the Separate rinse/Starchprogramme.

Change the spin speed if necessary.

Activate the Cap sensor if using acapsule.


Colour run and dye removers/dyes

Damage due to colour run/dyeremovers.Colour run and dye removers cancause corrosion in the washingmachine.Do not use colour run or dyeremovers in this washing machine.

Dyes suitable for use in domesticwashing machines can be used.However, please note that the salt usedin the dyeing process can causecorrosion to stainless steel componentsin the machine if you use dyefrequently. Always observe the dyemanufacturer's instructions carefully.

Cleaning and care

45

Cleaning the external casingand the control panel

Risk of electric shock!Mains voltage is present when thewashing machine is switched offDisconnect the machine from theelectricity supply before cleaning ormaintenance.

Risk of damage due to ingress ofwater.The pressure of a water jet cancause water to get into the washingmachine, resulting in damage tocomponents.Do not spray the washing machinewith a water jet.

Clean the casing and control panelwith a mild cleaning agent or soapand water and dry both with a softcloth.

The drum can be cleaned using asuitable stainless steel cleaning agentfollowing the manufacturer'sinstructions on the packaging.

Damage caused by cleaningagents.Solvent based cleaning agents,abrasive cleaners, glass cleaners ormulti-purpose cleaning agents cancause damage to plastic surfacesand other parts.Do not use any of these cleaningagents.

Cleaning the detergentdispenser drawer

Washing at low temperatures and theuse of liquid detergent can lead to abuild-up of mould and bacteria in thedetergent dispenser drawer.

For hygiene reasons, clean the entiredrawer at regular intervals.

Removing the dispenser drawer

Pull out the detergent dispenserdrawer until a resistance is felt. Pressdown the release button and at thesame time pull the drawer right out ofthe machine.

Clean the detergent drawer withwarm water.

Cleaning and care

46

Cleaning the siphon and the /compartment channel

Liquid starch results in clogging. Ifclogged, the siphon in the /compartment will not work and thecompartment can overflow.Clean the siphon particularlythoroughly after using liquid starch afew times.

1. Remove the siphon from compartment and clean under warmrunning water. Clean the siphon tubein the same way.

2. Replace the siphon.

Clean the fabric conditioner channelusing a brush and warm water.

Cleaning the detergent dispenserdrawer compartment

Use a bottle brush to removedetergent residues and limescalefrom the jets inside the detergentdispenser drawer compartment.

Replace the detergent dispenserdrawer.

Tip: Leave the detergent dispenserdrawer slightly open to allow it to dry.

Cleaning and care

47

Cleaning the drum (Hygiene info)Washing at low temperatures and/orusing liquid detergent can causebacteria and unpleasant odours to buildup in the washing machine. Use theCottons 90 °C programme to clean themachine. Run this programme at thelatest when the indicator lights up.

Cleaning the water inlet filtersThe washing machine has two filters toprotect the water inlet valve. Thesefilters should be checked every sixmonths or so, or more often if there arefrequent interruptions to the watersupply.

To clean the filter in the union in theopen end of the inlet hose:

First turn off the stopcock.

Unscrew the inlet hose from thestopcock.

Remove the rubber seal 1 from therecess.

Using pointed pliers, take hold of theplastic filter bar 2 and remove it.

Clean the filter.

Replace the filter and seal back in thereverse order and reconnect thehose.

To clean the filter in the water inletvalve:

Using pliers, carefully loosen theribbed plastic nut on the inlet valveand unscrew.

Use pointed nose pliers to withdrawthe plastic filter by the bar (seeillustration).

Clean the filter.

Replace the filter in the reverse order.

After cleaning the filters, turn on thestopcock and check the connectionis watertight. If water drips out,tighten the connection.

The two filters must be put back inplace after cleaning.

Problem solving guide

48

Many malfunctions and faults that can occur in daily operation can be easilyremedied. Time and money will be saved because a service call will not beneeded.

The following guide may help you to find the reason for a malfunction or a fault,and to correct it.

The programme does not start

Problem Cause and remedy

The control panelremains dark.

There is no power to the machine. Check whether the mains plug is plugged in and

switched on. Check whether the fuse or circuit breaker has

tripped.

The washing machine has switched off automaticallyto save energy. Switch the washing machine on again by turning

the programme selector.

and alternatelyappear in the timedisplay.

The door is not closed properly. The door lock couldnot engage. Close the door again. Start the programme again.

If the fault message appears again, contact theService Department.


49

The programme is cancelled and a fault indicator light lights upin the control panel


The fault indicator light lights up, and appear alternately in thetime display and thebuzzer sounds.

The water inlet is blocked or restricted. Check whether the stopcock is opened properly. Check whether the inlet hose is kinked. Check whether the water pressure is too low.

The filter in the water inlet is blocked. Clean the filter.


The water outlet is blocked or restricted.The drain hose has been fixed too high. Clean the drain filter and the drain pump. The maximum delivery head is 1 m.


The water protection system has reacted. Close the stopcock. Call the Service Department.

and alternatelyappear in the timedisplay and the buzzersounds.

There is a fault. Disconnect the washing machine from the mains

electricity supply, either by switching off at the wallsocket and withdrawing the plug, or bydisconnecting the relevant fuse on the mains fuseboard.

Wait at least 2 minutes, before reconnecting thewashing machine to the mains electricity supply.

Then switch the washing machine on again. Restart the programme.

If the fault message appears again, contact theService Department.


50

During the programme, a symbol appears in the time display

Message Cause and remedy

lights up The programme selector was moved to a differentposition after the programme had started. Turn the programme selector back to the original

position.

The programme has been interrupted. Open the door. Close the door.

At the end of the programme, an indicator light lights up in thecontrol panel


The indicator light lights up.

Excessive foam has built up during washing. Use less detergent next time, and follow the

manufacturer's recommended dosage amounts onthe packaging.

The indicator light lights up.

A programme using a temperature above 60 °C hasnot been run for a long time. In order to prevent bacteria and unpleasant odours

building up in the machine, run the Cottons 90 °Cprogramme using Miele machine cleaner orpowder detergent.


51

General problems with the washing machine


The washing machinesmells.

The indicator light was ignored. A washprogramme using a temperature above 60 °C has notbeen run for a long time. In order to prevent bacteria and unpleasant odours

building up in the washing machine, run theCottons 90 °C programme using Miele machinecleaner or a universal powder detergent.

The door and the detergent dispenser drawer wereleft shut after washing. Leave the door and the detergent dispenser

drawer slightly open to allow them to dry.

The machine shakesduring the spin cycle.

The machine feet are not level. Level the machine and adjust the feet correctly.

The laundry has notbeen spun properly andis still wet.

The machine detected an imbalance during the finalspin cycle and reduced the spin speed automatically. Include both large and small items in the load as

this will give better distribution during spinning.

Strange pump noisescan be heard.

This is not a fault.These slurping noises occur at the end of the pumpsequence as a normal part of operation.

Large amounts ofdetergent residueremain in the detergentdispenser drawer.

The water pressure is too low. Clean the water inlet filter. It may be useful to select the Water plus option.

Powder detergent used in conjunction with watersofteners tends to become sticky. In future, add washing powder into the dispenser

drawer first, and then add the water softener.


52

General problems with the washing machine


Fabric conditioner is notcompletely dispensedor too much waterremains in the compartment.

The siphon tube is not correctly positioned or isclogged. Clean the siphon, see “Cleaning and care -

Cleaning the detergent dispenser drawer”.

At the end of theprogramme there is stillliquid in the capsule.

The small pipe in the detergent dispenser draweronto which the capsule is placed is blocked. Clean the small pipe.

This is not a fault.For technical reasons a small amount of water willremain in the capsule.

There is water next tothe capsule in the fabricconditionercompartment

The sensor control was not activated. Make sure that you remember to activate the

sensor control the next time you insert acapsule.

An empty capsule was not removed at the end of thelast wash programme. Remove and dispose of the empty capsule at the

end of each programme.

There is a blockage in the small pipe in the detergentdrawer onto which the capsule is placed. Clean the small pipe.


53

An unsatisfactory wash result


Liquid detergent doesnot give the requiredresult.

Liquid detergents usually contain no bleachingagents. They do not remove fruit, coffee and teastains. Use a general purpose powder detergent

containing a bleaching agent. Use the appropriate capsule or add stain removers

to the compartment. Never put stain removers and liquid detergent

together in the dispenser drawer.

Grey, greasy particlescling to washed laundry.

Insufficient amounts of detergent were used to breakdown the particles of grease in heavily soiled laundry. Use more detergent. Before washing the next load run a Cottons 60°C

programme with powder detergent but without aload.

White residues whichlook like powderdetergent are seen ondark textiles afterwashing.

The detergent contained compounds (zeolites) to aidwater softening which are not soluble in water. Thesehave ended up on the laundry. Try and brush off the residues with a soft brush

once the laundry is dry. Wash dark textiles using a detergent which

contains no zeolites. Liquid detergents usuallycontain no zeolites.

Use the Dark garments / Denim programme fordark coloured laundry.


54

The door will not open


The door cannot bepulled open during aprogramme.

The door is locked during a programme. Touch the Start/Stop sensor to cancel the

programme.

The programme is cancelled, the door will unlock andyou will be able to pull it open.

There is still water in the drum and the machine isunable to drain. Clean the drain filters and the drain pump as

described in “Opening the door in the event of ablocked drain outlet and/or power failure”.

After the programme iscancelled, flashing bars......... appearin the time display.

For safety reasons the drum door cannot be openedif the suds temperature is higher than 55 °C. Wait until the temperature in the drum has

decreased and the bars have stopped flashing inthe display.

and alternatelyappear in the timedisplay.

The door lock has jammed. Call the Service Department.


55

Opening the door in the eventof a blocked drain outlet and/or power cut Switch off the washing machine.

Open the drain pump access panel.

Blocked drain outlet

If the drain outlet is blocked, there maybe a large quantity of water left behindin the washing machine.

Risk of scalding due to hot suds.Escaping suds will be hot if laundryhas been washed at hightemperatures!Carefully allow all suds to drain off.

Draining the washing machine

Remove the drain filter, though notcompletely.

Place a suitable container under theaccess panel, e.g. a universal oventray.

Slowly unscrew the drain filter to letthe water out.

Tighten the drain filter back up againif you need to interrupt the flow ofwater.

Once the flow of water ceases:

Remove the drain filter completely.


56

Clean the drain filter thoroughly.

Remove any foreign objects (e.g.,buttons, coins etc.) and clean theinterior. Turn the impellers by hand tocheck that they rotate freely.

Replace the drain filter correctly andtighten it securely.

Close the drain pump access panel.

Risk of water damage.Make sure the drain filter is securelytightened. Otherwise there is a risk ofwater leakage during use.Replace the drain filter correctly andtighten it securely.

Open the door

Danger of injury due to rotatingdrum!Reaching into a moving drum isextremely dangerous.Always make sure that the drum isstationary before reaching in toremove laundry.

Use a screwdriver to unlock the door.

Pull open the door.

Service

57

Contact in the event of a faultIn the event of any faults which youcannot remedy yourself, please contactyour Miele dealer or the Miele CustomerService Department.

You can book a Miele CustomerService Department call-out online atwww.miele.com/service.

Contact information for the MieleCustomer Service Department can befound at the end of this document.

Please quote the model identifier andserial number of your appliance (Fabr./SN/Nr.) when contacting the MieleCustomer Service Department. Thisinformation can be found on the dataplate.

Please note that telephone calls may bemonitored and recorded for trainingpurposes and that a call-out charge willbe applied to service visits where theproblem could have been resolved asdescribed in this booklet.

The data plate is found above theporthole glass when the door isopened.

Optional accessoriesOptional spare parts and accessoriesfor this washing machine are availablefrom your Miele Dealer, the Miele SpareParts Department or via the internet atwww.miele.co.uk.

Please note that telephone calls maybe monitored and recorded for trainingpurposes.

GuaranteeFor information on the applianceguarantee specific to your countryplease contact Miele. See end of thisbooklet for contact details.


Installation

*INSTALLATION*

58

Front view

a Water inlet hose (pressure tested to7000 kPa)

b Mains connection cable

c Flexible drain hose (with detachableswivel elbow)

d Control panel

e Detergent dispenser drawer

f Door

g Access to drain filters, drain pumpsand emergency release

h Four height-adjustable feet

Installation

*INSTALLATION*

59

Rear view

a Drain hose

b Transport clips for inlet and drainhoses and mains connection cable

c Mains connection cable

d Protruding lid for holding whenmoving the machine

e Water inlet hose (pressure tested to7000 kPa)

f Safety caps for transit bars

g Transport clips for inlet and drainhoses and for storing transit barswhen not in use

Installation

*INSTALLATION*

60

Installation surfaceA concrete floor is the most suitableinstallation surface. It is far less proneto vibration during the spin cycle thanwooden floorboards or a carpetedsurface.

Please note:

The machine must be level andsecurely positioned.

To avoid vibrations during spinning,the machine should not be installedon soft floor coverings.

If installing on a wooden joist floor:

Install the machine on a plywoodbase (at least 59 x 52 x 3 cm). Thebase should span several joists andbe bolted to the joists and not only tothe floorboards. Check for thepresence of pipes and cables first.

Tip: If possible, install the machine in acorner. This is usually the most stablepart of the floor.

Injury can occur if the washingmachine has not been adequatelysecured.During installation, the washingmachine must be secured on a plinthto be made available on site(concrete or brick), in order to ensureit cannot fall or slip.Secure the washing machine using aclamp/fastening bracket (MTS floormounting kit – available from yourMiele dealer or Miele spare partsdepartment).

Transporting the washingmachine to its installation site

Danger of injury due to unsecurelid.Make sure the fixings at the back ofthe lid are secure. Otherwise there isa danger of the lid being pulled offwhen carrying the machine.Before carrying the machine checkthat the lid is secure where itprotrudes at the back of themachine.

Carry the washing machine by thefront feet and by the lid where itprotrudes at the back of theappliance.

Removing the transit bars

Remove the left and right covers.

1. Pull off the transit bar covers and

2. then use a screwdriver to release thecatches at the top and bottom.

Installation

*INSTALLATION*

61

Using the spanner supplied, turn theleft-hand transit bar 90°, then

withdraw the transit bar.

Turn the right-hand transit bar 90°,then

withdraw the transit bar.

Installation

*INSTALLATION*

62

Risk of injury from sharp edges.There is a risk of injury from reachinginto holes that are not covered.Cover the holes for the transit barsafter they have been removed.

Fit the stoppers onto the two holes.

Secure the transit bars to the back ofthe washing machine. Make sure thatthe top catch is located above theholder.

Risk of damage from incorrecttransport.The washing machine may becomedamaged if moved without the transitbars in place.Keep the transit bars in a safe place.Fit them again if the machine is to bemoved (e.g. when moving house).

Re-fitting the transit barsRe-fitting is carried out by reversing theprocedure.

Installation

*INSTALLATION*

63

Levelling the machineThe washing machine must standperfectly level on all four feet to ensuresafe and proper operation.

Incorrect installation may increaseelectricity and water consumption andmay cause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are usedfor levelling the washing machine. Themachine is supplied with all four feetare screwed in.

Using the spanner supplied, turncounter nut 2 in a clockwise direction.Then turn counter nut 2 together withfoot 1 to unscrew.

Use a level to check that the washingmachine is standing level.

Hold foot 1 securely with a pipewrench. Turn counter nut 2 againusing the spanner supplied until it sitsfirmly up against the housing.

Risk of damage due toincorrectly aligned washing machine.There is a danger of the washingmachine moving about if the feet arenot secured.Turn all four counter nuts for the feetuntil they sit firmly up against thehousing. Please also check this forthe feet which did not needadjustment.

Installation

*INSTALLATION*

64

Installing under a continuousworktop

Risk of electric shock due toexposed cablesThere is a risk of coming into contactwith live parts while the lid isremoved.Building under kits* must only beinstalled/dismantled by a suitablyqualified fitter in accordance with theinstructions supplied.

– A special building under kit* isrequired. The cover plate suppliedwith the building under kit is used toreplace the machine lid. It isnecessary to fit the coverplate forelectrical safety reasons.

– Connections for electricity, water anddrainage should be installed in such away that they remain accessiblewhen the machine is in its finalposition.

Fitting instructions are supplied with thebuilding-under kit.

Washer-dryer stack

The washing machine can be combinedwith a Miele tumble dryer in a washer-dryer stack. The appropriate “WTV”stacking kit* to match your dryer isrequired.

All parts marked* are available fromyour Dealer or Miele.

Please note:

a = at least 2 cm

b = WTV without drawer: 172 cmWTV with drawer: 181 cm

c = 64 cm

Installation

*INSTALLATION*

65

The water protection systemThe Miele water protection systemprotects all parts of the washingmachine from water damage.

The system consists of three maincomponents:

– the inlet hose

– the electronic unit and drainage andoverflow protection

– the drain hose

Inlet hose

– Protection against bursting

The inlet hose is tested to withstandpressure of at least 7,000 kPa.

Electronic unit and washing machinehousing

– SumpAny leaking water is collected in asump in the base of the machine. Afloat switches off the water inletvalves, preventing any more waterfrom flowing into the machine andwater in the suds container ispumped away.

– Overflow protectionThis prevents the washing machinetaking in too much water. If the waterlevel exceeds a certain level, thedrain pump switches in and pumpsthe excess water away.

Drain hose

The drain hose is protected by aventilation system which prevents thewashing machine from being emptiedcompletely.

Installation

*INSTALLATION*

66

Connection to the water supply

Health risk and risk of damagedue to contaminated incoming water.The quality of the incoming watermust correspond to the drinkingwater specification of the country inwhich the washing machine is beingoperated.Always connect the washingmachine to the mains water supply.

The washing machine should beconnected to the mains water supply inaccordance with current local andnational safety regulations. The Germanauthorities do not require it to have anon-return valve as the washingmachine has been designed to complywith DIN regulations.

The water connection pressure needsto be between 100 kPa and 1000 kPa. Ifthe water connection pressure exceeds1000 kPa, a pressure reducing valvemust be installed.

A stopcock with a ¾ inch threadedunion is required for the connection. Ifthis is not available, only a qualifiedinstaller may connect the washingmachine to the mains water supply.

The connection point is subject tomains water pressure.Turn on the stopcock slowly andcheck for leaks. Correct the positionof the washer and the threadedunion if necessary.

The washing machine is not suitablefor connection to a hot water supply.The washing machine must not beconnected to a hot water supply.

Maintenance

Only use a genuine Miele hose that hasbeen pressure tested to withstand atleast 7,000 kPa should you ever need areplacement.

Damage caused by dirty water.A filter is located in the open end ofthe inlet hose and another in theintake point to protect the inlet valvein the washing machine.These filters must not be removed.

Hose extension

Longer hoses 2.5 or 4.0 m in length areavailable from your Miele Dealer orMiele as optional extras.

Installation

*INSTALLATION*

67

Water drainageThe suds are drained through a drainpump with a 1 m delivery head. For thewater to drain freely, the hose must befree of kinks.If required, the hose can be extended toa length of up to 5 m. Accessories areavailable from Miele or from your Mieledealer.

For a delivery head of more than 1 m(up to a max. of 1.8 m) a replacementdrain pump will need to be fitted.Please contact Miele for advice.For a delivery head of 1.8 m the hosecan be extended to a length of up to2.5 m. Accessories are available fromMiele or from your Miele dealer.

Drainage options:

1. Directed into a sink or basin:

Please note:

– Hook the hose over the edge andsecure it.

– If the water is pumped into awashbasin, make sure that it candrain away freely. Otherwise thereis a risk of water overflowing or ofsome of the drained water beingsucked back into the machine.

2. Connected securely to a plastic drainpipe with a rubber nipple (there is noneed to use a siphon).

3. Connected securely to a floor drain(gully).

4. Connected securely to a washbasinwith plastic nipple.

Please note:

a Adapter

b Spigot nut

c Hose clip

d End of the hose

Fit adapter to the sink drain outletusing nut .

Attach the end of hose to adapter.

Use a screwdriver to tighten hose clip up close to the nut.

Installation

*INSTALLATION*

68

Electrical connectionThe washing machine is supplied withan electrical connection cable withmoulded plug ready for connection to aswitched socket.

The socket must be easily accessibleafter the washing machine has beeninstalled. If that is not possible, ensurethat a suitable means of disconnectionis provided on the installation side foreach pole.

Risk of fire from overheating.Connecting the washing machine toa multi-socket plug adapter or to anextension lead can overload thecable.Do not use an extension lead ormulti-socket plug adapter.

The electrical system must comply withlocal and national safety regulations(BS 7671 in the UK). We recommendthe use of a suitable RCD .

If the connection cable is damaged, itmust only be replaced with a specificconnection cable of the same type(available from the Miele CustomerService Department). For safetyreasons, such replacement may only becarried out by a qualified technician orthe Miele Customer ServiceDepartment.

The data plate indicates the nominalpower consumption and theappropriate fuse rating. Compare thespecifications on the data plate withthose of the electricity supply and makesure that they match.

If in any doubt, consult a qualifiedelectrician.

Do not connect the washing machine toa stand-alone inverter such as thoseused with an autonomous energysource, e.g. solar power. When thewashing machine is switched on, powersurges could result in a safety switch-off. This could damage the electronicmodule.

Technical data

69

Height 850 mm

Width 596 mm

Depth 636 mm

Depth with door open 1054 mm

Height for building under 820 (+8/-2) mm

Width for building under 600 mm

Depth for building under 600 mm

Weight Approx. 100 kg

Capacity 8 kg dry laundry

Voltage See data plate

Connected load See data plate

Fuse rating See data plate

Consumption data See “Consumption data”

Minimum flow pressure 100 kPa

Maximum flow pressure 1000 kPa

Inlet hose length 1.60 m

Drain hose length 1.50 m

Mains connection cable length 2.00 m

Delivery head max. 1.00 m

Maximum drainage length 5.00 m

LEDs Class 1

Test certificates awarded See data plate

Consumption data

70

Load Energy Water Duration Residualmoisture

kg kWh Litres h:min %

Cottons 60 °C* 8.0 0.90 45 2:59 53

60 °C 4.0 0.88 48 2:59 53

40 °C 4.0 0.53 39 2:59 53

Cottons 90 °C 8.0 2.10 49 2:29 53

60 °C 8.0 1.35 49 2:29 53

60 °C 4.0 1.15 48 2:19 53

40 °C 8.0 0.98 54 2:39 53

20 °C 8.0 0.35 54 2:39 53

Minimum iron 30 °C 3.5 0.45 52 1:59 30

Delicates 30 °C 2.0 0.25 30 1:09 –

Woollens 30 °C 2.0 0.23 35 0:38 –

Express 201) 40 °C 3.5 0.34 30 0:20 –

Shirts 60 °C 2.0 0.77 40 1:31 –

1) Short extra option activated

Consumption data can vary from the nominal values given depending on waterpressure, water hardness, water inlet temperature, room temperature, type andvolume of load, fluctuations in the electricity supply and any extras selected.

Note for test institutes*Test programme in accordance with IEC 60456 or EN 60456.

Programmable functions

71

The programmable functions are usedto alter the machine's electronics tosuit changing requirements.Programmable functions can bealtered at any time.

The programming is carried out in eightsteps (, , ... ) using the sensorcontrols.

Accessing the programming level

Pre-requisites:

– The washing machine is switched on(the programme selector is pointingto a wash programme).

– The washing machine door is open.

Touch the Start/Stop sensor andleave your finger on it whilst carryingout steps -.

Close the washing machine door.

Wait until the Start/Stop sensor lightsup constantly ...

... and then take your finger off theStart/Stop sensor.

After approx. four seconds, will lightup in the time display.

Choosing and selecting aprogrammable function

The number of the programmablefunction will appear in the time displayas and a number: e.g. .

Touch the or sensor to scroll tothe next or previous programmablefunction:


Keypad tone

Lock code

Control panel standby status

Memory

Additional pre-wash time -Cottons

Soak duration

Gentle action

Reduced temperature

Water plus

Water plus level

Maximum rinse level

Suds cooling

Anti-crease

Backlight brightness

Confirm the selected programmablefunction by pressing the Start/Stopsensor.


72

Editing and saving theprogrammable functionYou can either switch a programmablefunction on or off or select differentoptions.

Touch the or sensor to switchthe programmable function on/off orto select an option:

Programmable function

Available options

–

X O

O X

X O

O X

O X X X

O X X X

O X

O X

O X X

O X X X

O X

O X

X O

X X O X X

X = Can be selected

O = Factory setting

Confirm the chosen selection withthe Start/Stop sensor.

The number of the programmablefunction: e.g. will light up again.

Exit programming level Turn the programme selector to .

The option you have selected is nowstored in memory. You can change itagain at any time.

Keypad tone

Each touch of a sensor is confirmedwith an audible tone.

Options

= Keypad tone switched off

= Keypad tone switched on(factory default setting)


73

Lock code

The lock code prevents the washingmachine being used without yourknowledge.

When the code has been activated, youhave to enter a code after switching thewashing machine on. Otherwise thewashing machine cannot be operated.

Options

= Lock code switched off(factory default setting)

= Lock code is switched on

Using the washing machine with alock code

The code is 125 and cannot be altered.

Switch on the washing machine.

appears in the time display andthe and sensors light up.

Touch the sensor.

appears in the time display.

Confirm the number with the Start/Stop sensor.

The first number was saved and youcan now enter the second numberusing the and sensors.

Also enter the second and thirdnumbers and confirm the numberswith the Start/Stop sensor.

The lock is released and a washprogramme can now be selected andstarted.

Control panel switch-offstatus

To save energy the time display andsensors will go out after 10 minutes,and only the Start/Stop sensor willflash slowly.

Options

= OffThe time display and sensorswill remain lit up while thewashing machine is switchedon

= On (factory default setting)The time display and sensorswill switch off after 10 minutesif the programme is started.

However; the time display andsensors will remain lit up for10 minutes after a delay starttime has elapsed, after the endof the programme or at the endof the anti-crease phase.


74

Memory

The washing machine will save thelast settings (temperature, spin speedand some of the extras) selected for aprogramme after the programme hasstarted.

When this programme is chosen again,these saved settings will appear in thedisplay.

Options

= Memory is switched off(factory default setting)

= Memory is switched on

Longer pre-wash Cottons

If you require a longer pre-wash youcan extend the pre-wash time.

Options

= No increase in the pre-washtime (factory default setting)

= + 6 minutes increase in thepre-wash time



Soak duration

You can set a duration for the soakprocess of between 30 minutes andtwo hours.

You can select the duration in 30 minuteincrements. When the Soak Extra optionis selected the laundry will be soakedfor the duration selected.

Options

= 30 minutes soak duration(factory default setting)

= 1 hour soak duration

= 1 hour 30 minutes soakduration

4 = 2 hours soak duration

Gentle action

Activating gentle action reduces thedrum action and is suitable forwashing lightly soiled items moregently.

Gentle action can be activated for theCottons and Minimum ironprogrammes.

Options

= Gentle action is switched off(factory default setting)

= Gentle action rhythm isswitched on


75

Reduce temperature

The boiling point for water is lower athigh altitudes. In order to avoid waterboiling, Miele recommend activatingthe reduce temperature setting ataltitudes of more than 2000 m abovesea level. The maximum temperatureis reduced to 80 °C even when ahigher temperature is selected.

Options

= The reduce temperature settingis switched off (factory defaultsetting)

= The reduce temperature settingis turned on

Water plus

You can determine the amount ofwater used if the Water plus extra isselected.

Options

= More water is used in the washand rinse stages (factorydefault setting)

= An extra rinse is carried out

= The water level is increased inthe wash and rinse stages andan additional rinse is carriedout

Water plus level

There are three different water levelswhich can be selected by activatingthe Water plus extra.

Options

= No higher water level (factorydefault setting)

= Water level increase by 1 levelwhen washing and rinsing

= Water level increase by 2 levelswhen washing and rinsing

= Water level increase by 3 levelswhen washing and rinsing

Maximum rinse level

The water level in the rinse cycle canbe permanently set to the highestvalue.

This function is useful for allergysufferers as it achieves an excellentrinse result. Water consumption willincrease.

Options

= Maximum rinse level isswitched off (factory defaultsetting)

= Maximum rinse level isswitched on


76

Suds cooling

When this is activated, additionalwater flows into the drum at the end ofthe main wash to cool the suds down.Hot suds can damage plastic drainagepipes.

Suds cooling takes place when atemperature of 70 °C or higher isselected for the Cottons programme.

Suds cooling should be activated:

– to prevent the danger of scalding ifthe drain hose is hooked over theedge of a sink or basin.

– where drainage pipes do not complywith DIN 1986.

Options

= Suds cooling is switched off(factory default setting)

= Suds cooling is switched on

Anti-crease

The anti-crease function helps preventcreasing if laundry is not going to beremoved immediately after the end ofthe programme.

The drum continues to turn at intervalsfor up to 30 minutes at the end of theprogramme. The door can be opened atany time.

Options

= The anti-crease function isswitched off

= The anti-crease function isswitched on (factory defaultsetting)

Backlight brightnessdimmed

The brightness of the dimmed sensorsin the control panel can be set to oneof seven different levels.

The brightness changes as soon as youselect a different setting.

Options

= Darkest level

= Lightest level

= (Factory default setting)

Optional accessories

77

Detergent, fabric care, additives andmachine care products are available forthis washing machine. All the productshave been designed for Miele washingmachines.

These and many other useful productscan be ordered via the internet atwww.miele.co.uk or from Miele (see endof this booklet for contact details).

Detergent

UltraWhite

– Multi-purpose powder detergent

– For white and light-coloured laundryas well as heavily soiled cotton items

– Effective stain removal even at lowtemperatures

UltraColor

– Liquid detergent for coloured items

– For coloured and dark fabrics

– Protects bright colours from fading

– Effective stain removal even at lowtemperatures

Wool and delicates detergent

– Liquid detergent for delicates

– Particularly suitable for woollen andsilk fabrics

– Cleans at temperatures as low as20 °C, helps retain the shape ofdelicate items and protect colours

Specialist detergentsSpecialist detergents are available ascapsules in convenient single doseamounts or in a handy bottle.

Outerwear

– Liquid detergent for outerwear andperformance clothing

– Cleans with care and is gentle oncolours

– With lanolin to care for and conditionmembrane fabric

Sport

– Liquid detergent for sportswear andfleece garments

– Neutralises unpleasant odours

– Retains the shape of the items

Down

– Liquid detergent suitable for pillows,sleeping bags, and down-filled items

– Retains the elasticity of down andfeather-filled items

– Retains the breathability of down-filled items

– Prevents down filling clumpingtogether


Optional accessories

78

WoolCare

– Liquid detergent for woollens anddelicates

– Includes a special wheat proteinconditioning formula

– Helps prevent felting

– Gentle on colours

– Only available as capsules

SilkCare

– Liquid detergent for silks

– Contains a special silk proteinconditioning formula

– Gentle on colours

– Only available as capsules

Fabric careFabric care is available as capsules in convenient single dose amounts or ina handy bottle.

Proofing agent

– For proofing microfibre fabrics, e.g.rain coats

– Retains the breathability of fabrics

Fabric conditioner

– Fresh, natural fragrance

– Makes laundry soft to handle

Additive

Booster

– For removing stains

– For white and coloured laundry

– Available as capsules inconvenient single dose amounts

Machine care

Machine cleaner

– For cleaning the washing machinethoroughly and effectively

– Removes grease, bacteria, andassociated unpleasant odours

– Use 1–3 times per year

Descaling agent

– removes heavy limescale deposits

– Mild and gentle with natural citricacid

Water softener tablets

– Reduces the amount of detergentneeded for hard water

– Less detergent residue in fabrics

– Less chemicals in waste water due toreduced amount of detergent

Germany

Miele Pte. Ltd.163 Penang Road# 04 - 03 Winsland House IISingapore 238463Tel:Fax:E-Mail: [email protected]: www.miele.sg

Miele & Cie. KGCarl-Miele-Straße 2933332 Gütersloh

+65-67351191+65-67351161

Singapore

ThailandBHIRAJ TOWER at EmQuartier43rd Floor Unit 4301-4303 689 Sukhumvit RoadNorth Klongton Sub-DistrictVadhana DistrictBangkok 10110, Thailand

MalaysiaMiele Sdn BhdSuite 12-2, Level 12Menara Sapura Kencana PetroleumSolaris Dutamas No. 1Jalan Dutamas 150480 Kuala Lumpur, MalaysiaPhone: +603-6209-0288Fax: +603-6205-3768

M.-Nr. 10 835 960 / 01en-SG

WDD 020 EcoPlus&Comfort

Operating instructions for washing machines - miele.sg · Miele. If other parts are used, warranty,...

Documents

Transcript of Operating instructions for washing machines - miele.sg · Miele. If other parts are used, warranty,...