OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS KIARO · BRACKETS INSTALLATION WIRE INSTALLATION...
Transcript of OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS KIARO · BRACKETS INSTALLATION WIRE INSTALLATION...
1
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
KIARO
PAT. PENDING
2
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
250
275
300
325
350
375
400
H (mm)
DOOR WEIGHT (Kg)
10 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
425
450
475
5001 Kiaro
1 or 2 Kiaro
2 Kiaro
ITALIANA FERRAMENTA s.r.l. Viale Europa 17 - Z.I. del Camol - 33070 Brugnera (PN) Italy - Tel. +39 0434 428211 - Fax +39 0434 428242 - E-mail: [email protected] - www.italianaferramenta.com
APPLICATION CHART FOR KIARO
April 2019
hKg = Door weight including the possible handle.
MECHANISM INSTALLATION
ADJUSTMENT OF STRENGTH SETTINGS
NO SETTING
Lo
ad
Lo
ad
Lo
ad
Lo
adSETTING “A” SETTING “B” SETTING “A+B”
Included bespoke screws
Screw slots for the adjustment of strength settings
In case the door weight/dimensions are bigger or smaller than those reported on the chart, our technical department is at your disposal to test further cases out of this chart.
Door weight including the possible handle.
DOOR WEIGHT (Kg)
H (mm)
1 Kiaro
2 Kiaro
1 or 2 Kiaro (In accordance with the actual European regulation, we suggest to use two KIARO mechanisms)
3
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
7,5130
55
91
12
7,5
7
MECHANISM INSTALLATION
MECHANISM FIXING
On the bottom and on the side panel with screws
On the bottom and on the side panel with pin and screws
STEP 1
STEP 1
STEP 1
STEP 2
STEP 2
On the back panel with screws
UNHANDED MECHANISM
pan head screws Ø3,5 x 18
hole Ø5 x 8 mm
hole Ø5 x 8 mm
pan head screws Ø3,5 x 18
4
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
LL1
L1 + L
click
BRACKETS INSTALLATION WIRE INSTALLATION
Countersunk head Euro screw Ø 5 x 13 mm
Countersunk head wood screw Ø 3,5 x 16 mm
STEP 2STEP 1
STEP 1
STEP 2
STE
P 1
STE
P 2
WIRE INSERTION ONTO THE DOOR BRACKET
COVER CAP AND ALUMINIUM LATERAL PROFILE INSERTION
Lift the door almost completely to slot the end element of the wire into the door bracket.
Place the cover cap on the door bracket before lifting the door.
5
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
-14°
+3°
DOOR OPENING ANGLE ADJUSTMENT
FROM THE INSIDE OF THE CABINET
ADJUSTMENT OF STRENGTH SETTINGS
OK NO
FROM THE BACKSIDE OF THE CABINET
VERY IMPORTANT:The opening angle adjustment can be carried out only with open door.
VERY IMPORTANT:Before proceeding, make sure:
1) The door is completely closed.
2) The mechanism is completely in position.
Possibility to adjust the settings of the mechanism also upon completed assembly.For details refer to the related section.
In this case put the small flap in position with a screwdriver.
6
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
LL1
L1 + L
click
INSTRUCTIONS FOR WIRE CUTTING
INSERTION OF THE WIRE INTO THE END PART AND LOCKING WITH M3 GRUBSCREW
WIRE CUTTING WITH UNMOUNTED MECHANISM
S1,5 mm Allen wrench
STEP 2Pull
STEP 3Completely lock the grubscrew once the length corresponds to the needed dimension.
In order to obtain the exact length, it is necessary to stretch the wire without pulling it out.
VERY IMPORTANT:Before cutting, it is necessary to lock the grub screw heavily.
STEP 1Push
WIRE CUTTING WITH MOUNTED MECHANISM
In order to obtain the exact length, it is necessary to stretch the wire without pulling it out.
VERY IMPORTANT:Before cutting, it is necessary to lock the grub screw heavily.
7
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
8
12,5
B
L
B = L - 45 mm
A 46006000YA A = 600 mm
4600 _ _ _ 0YA A = _ _ _ mm
46205500UT B = 550 mm
4620 _ _ _ 0UT B = _ _ _ mm
1 2 3 4
1 2 3 4
ZA
AL
EP ST = 12 pcs.
= 12 pcs.
118
73,6
232 14,8
52
11,5 10 1
CUT TO SIZE RULE:
8
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
A46006000YQ A = 600 mm
4600 _ _ _ 0YQ A = _ _ _ mm
46205500FV B = 550 mm
4620 _ _ _ 0FV B = _ _ _ mm
1 2 3 4
1 2 3 4
ZA
AL
EP ST = 12 pcs.
= 12 pcs.
118
73,6
232 14,8
52
11,5 10 1
8
12,5
B
L
B = L - 45 mm
CUT TO SIZE RULE:
9
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
62501050ZN
ST
1 2 3 4
= S 1,5 mm
= 1.000 pcs.
16 Ø7
Ø3,
5
Ø3
18 min.
60101390ZN
ST
= Ø 3 mm
= PZ2
1 2 3 4
+
= 10.000 pcs.
45
14
18Ø
3,5
7,57,5
Ø4,
5
7Ø5
8
60103150ZN
10101010ZN
ST
ST
1 2 3 4
1 2 3 4
= PZ2
= Ø 3 mm
= Ø 5 mm
= 10.000 pcs.
= 5.000 pcs.
ACCESSORIES FOR MECHANISM FIXING
ACCESSORY FOR DOOR BRACKET FIXING
ACCESSORY FOR LOCKING THE GRUB SCREW
10
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
105
90 105
27
2,5
32 34
32 32
Ø12
4
4
7650
,4
4,4
9,5
12,4
50,4
28,5
41,6
28,5
12,4
9,5
10
R2,5
R2,5
R5
3
10,5
5 5
50,4
-14°
+3°
87°
Ø5x12
15 min.
KIARO WITH STANDARD UNSPRUNG HINGESIn case other hinges than KIMANA are used, it is necessary to contact an authorized dealer for a correct drilling scheme.
For this purpose, use the form at the end of the KIARO section to provide the required specifications.
BOTTOM BOTTOMDO
OR
DOOR
Overcrossing 90° door opening angle, negatively affects the Kimana hinges.
In case of door without handles it is recommended to use K Push Tech with buffer.
L (78 min.)
optional Ø8mm hole for opening angle adjustment
side
-pan
el
inne
r si
de
Ø2,5 spot drilling
(If L < 140 do not operate these drillings.)
SIDE-PANEL DRILLING OPERATIONS
BACK-PANEL DRILLING OPERATIONS
DOOR PANEL DRILLING OPERATIONS
KIARO WITH KIMANA HINGE
11
8
OPENING SYSTEMS FOR LIFT UP AND DROP DOWN DOORS
Please fill in and send back to your authorized reseller
KIND OF HINGES
KIMANA hinges
STANDARD UNSPRUNG hinges Other hinges
(Recommended)
CUSTOMER:
REFERENCE:
DATE
Please specify producer, article code, mounting plate Please specify producer, article code, mounting plate
FLAP hinges
CLOSING CONDITION OPENING CONDITION
Thickness
Thickness
Dimension
Dimension
Dimension
Bottom Bottom DoorDoo
r
C
B
A
D
Th
Please, fill-in with correct dimensions
13 mm98 mm
78 mm min.
CABINETWIDTH
mm
A
DOORTHICKNESS
mm
Th
DOORWIDTH
mm
D
DOORWEIGHT
kg
E
DOORHEIGHT
mm
C
SERVICEGAP
mm
FBACK PANELTHICKNESS
mm
G
INTERNALDEPTH
mm
I
CABINETHEIGHT
mm
B
(15 mm min.)
F G
I
L
KIARO FINISHEST-Met Gunmetal
E
SIDE PANELWIDTH
mm
L
Dimension
Please photocopy, fill in and send back to your authorized reseller