PRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.

APPLICATIONS TRANSDUCER APPLICATIONS TEMPERATURE MEASUREMENT ELECTRONIC SCALES MEDICAL INSTRUMENTATION BATTERY-POWERED INSTRUMENTS HANDHELD TEST EQUIPMENT

0.05µV/°C max, SINGLE-SUPPLYCMOS OPERATIONAL AMPLIFIERS

Zerø-Drift Series

FEATURES LOW OFFSET VOLTAGE: 5µV (max) ZERO DRIFT: 0.05µV/°C (max) QUIESCENT CURRENT: 285µA SINGLE-SUPPLY OPERATION SINGLE AND DUAL VERSIONS SHUTDOWN MicroSIZE PACKAGES

DESCRIPTIONThe OPA334 and OPA335 series of CMOS operationalamplifiers use auto-zeroing techniques to simultaneouslyprovide very low offset voltage (5µV max), and near-zero driftover time and temperature. These miniature, high-precision,low quiescent current amplifiers offer high input impedanceand rail-to-rail output swing. Single or dual supplies as low as+2.7V (±1.35V) and up to +5.5V (±2.75V) may be used.These op amps are optimized for low-voltage, single-supplyoperation.

The OPA334 family includes a shutdown mode. Under logiccontrol, the amplifiers can be switched from normal operationto a standby current of 2µA. When the Enable pin is con-nected high, the amplifier is active. Connecting Enable lowdisables the amplifier, and places the output in a high-impedance state.

The OPA334 (single version with shutdown) comes inMicroSIZE SOT23-6. The OPA335 (single version withoutshutdown) is available in SOT23-5, and SO-8. The OPA2334(dual version with shutdown) comes in MicroSIZE MSOP-10.The OPA2335 (dual version without shutdown) is offered inthe MSOP-8 and SO-8 packages. All versions are specifiedfor operation from –40°C to +125°C.

OPA334OPA2334

OPA335OPA2335

SBOS245D – JUNE 2002 – REVISED JULY 2003

Copyright © 2002-2003, Texas Instruments Incorporated

OFFSET VOLTAGE PRODUCTION DISTRIBUTION

Offset Voltage (µV)

–3.0

–2.7

–2.4

–2.1

–1.8

–1.5

–1.2

–0.9

–0.6

–0.3 0

0.3

0.6

0.9

1.2

1.5

1.8

2.1

2.4

2.7

3.0

Pop

ulat

ion

OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION

Offset Voltage Drift (µV/°C)

Pop

ulat

ion

0

0.00

5

0.01

0

0.01

5

0.02

0

0.02

5

0.03

0

0.03

5

0.04

0

0.04

5

0.05

0

Absolute Value;Centered Around Zero

OPA2334

OPA335OPA2335

OPA2335

www.ti.com

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

All trademarks are the property of their respective owners.

2www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

SPECIFIEDPACKAGE TEMPERATURE PACKAGE ORDERING TRANSPORT

PRODUCT PACKAGE-LEAD DESIGNATOR(1) RANGE MARKING NUMBER MEDIA, QUANTITY

Shutdown VersionOPA334 SOT23-6 DBV –40°C to +125°C OAOI OPA334AIDBVT Tape and Reel, 250

" " " " " OPA334AIDBVR Tape and Reel, 3000

OPA2334 MSOP-10 DGS –40°C to +125°C BHE OPA2334AIDGST Tape and Reel, 250" " " " " OPA2334AIDGSR Tape and Reel, 2500

Non-Shutdown VersionOPA335 SOT23-5 DBV –40°C to +125°C OAPI OPA335AIDBVT Tape and Reel, 250

" " " " " OPA335AIDBVR Tape and Reel, 3000OPA335 SO-8 D –40°C to +125°C OPA335 OPA335AID Rails, 100

" " " " " OPA335AIDR Tape and Reel, 2500

OPA2335 SO-8 D –40°C to +125°C OPA2335 OPA2335AID Rails, 100" " " " " OPA2335AIDR Tape and Reel, 2500

OPA2335 MSOP-8 DGK –40°C to +125°C BHF OPA2335AIDGKT Tape and Reel, 250" " " " " OPA2335AIDGKR Tape and Reel, 2500

NOTE: (1) For the most current specifications and package information, refer to our web site at www.ti.com.

Supply Voltage .................................................................................... +7VSignal Input Terminals, Voltage(2) ........................... –0.5V to (V+) + 0.5V

Current(2) .................................................. ±10mAOutput Short Circuit(3) .............................................................. ContinuousOperating Temperature .................................................. –40°C to +150°CStorage Temperature .....................................................–65°C to +150°CJunction Temperature .................................................................... +150°CLead Temperature (soldering, 10s) ............................................... +300°C

NOTES: (1) Stresses above these ratings may cause permanent damage.Exposure to absolute maximum conditions for extended periods may de-grade device reliability. These are stress ratings only, and functional opera-tion of the device at these, or any other conditions beyond those specified,is not implied. (2) Input terminals are diode-clamped to the power-supplyrails. Input signals that can swing more than 0.5V beyond the supply railsshould be current-limited to 10mA or less. (3) Short-circuit to ground, oneamplifier per package.

ABSOLUTE MAXIMUM RATINGS(1)

PACKAGE/ORDERING INFORMATION

ELECTROSTATICDISCHARGE SENSITIVITY

This integrated circuit can be damaged by ESD. TexasInstruments recommends that all integrated circuits be handledwith appropriate precautions. Failure to observe proper han-dling and installation procedures can cause damage.

ESD damage can range from subtle performance degrada-tion to complete device failure. Precision integrated circuitsmay be more susceptible to damage because very smallparametric changes could cause the device not to meet itspublished specifications.

PIN CONFIGURATIONS

NOTES: (1) NC indicates no internal connection. (2) Pin 1 of the SOT23-6 isdetermined by orienting the package marking as indicated in the diagram.

1

2

3

5

4

V+

–In

Out

V–

+In

OPA335

SOT23-5

1

2

3

4

8

7

6

5

NC(1)

V+

Out

NC(1)

NC(1)

–In

+In

V–

OPA335

SO-8

1

2

3

4

8

7

6

5

V+

Out B

–In B

+In B

Out A

–In A

+In A

V–

OPA2335

SO-8, MSOP-8

A

B

1

2

3

6

5

4

V+

Enable

–In

Out

V–

+In

OPA334(2)

OA

OI

SOT23-6

1

2

3

4

5

10

9

8

7

6

V+

Out B

–In B

+In B

Enable B

Out A

–In A

+In A

V–

Enable A

OPA2334

MSOP-10

A

B

3www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

OPA334AI, OPA335AIOPA2334AI, OPA2335AI

ELECTRICAL CHARACTERISTICSBoldface limits apply over the specified temperature range, TA = –40°C to +125°C.At TA = +25°C, VS = +5V, RL = 10kΩ connected to VS/2, and VOUT = VS /2, unless otherwise noted.

PARAMETER CONDITION MIN TYP MAX UNITS

OFFSET VOLTAGEInput Offset Voltage VOS VCM = VS/2 1 5 µV

vs Temperature dVOS /dT ±0.02 ±0.05 µV/°Cvs Power Supply PSRR VS = +2.7V to +5.5V, VCM = 0, Over Temperature ±1 ±2 µV/VLong-Term Stability(1) See Note (1)

Channel Separation, dc 0.1 µV/V

INPUT BIAS CURRENTInput Bias Current IB VCM = VS/2 ±70 ±200 pA

Over Temperature 1 nAInput Offset Current IOS ±120 ±400 pA

NOISEInput Voltage Noise, f = 0.01Hz to 10Hz en 1.4 µVPP

Input Current Noise Density, f = 10Hz in 20 fA/√Hz

INPUT VOLTAGE RANGECommon-Mode Voltage Range VCM (V–) – 0.1 (V+) – 1.5 VCommon-Mode Rejection Ratio CMRR (V–) – 0.1V < VCM < (V+) – 1.5V, Over Temperature 110 130 dB

INPUT CAPACITANCEDifferential 1 pFCommon-Mode 5 pF

OPEN-LOOP GAINOpen-Loop Voltage Gain, Over Temperature AOL 50mV < VO < (V+) – 50mV, RL = 100kΩ, VCM = VS/2 110 130 dB

Over Temperature 100mV < VO < (V+) – 100mV, RL = 10kΩ, VCM = VS/2 110 130 dB

FREQUENCY RESPONSE

Gain-Bandwidth Product GBW 2 MHzSlew Rate SR G = +1 1.6 V/µs

OUTPUTVoltage Output Swing from Rail RL = 10kΩ, Over Temperature 15 100 mVVoltage Output Swing from Rail RL = 100kΩ, Over Temperature 1 50 mVShort-Circuit Current ISC ±50 mACapacitive Load Drive CLOAD See Typical Characteristics

SHUTDOWNtOFF 1 µstON

(2) 150 µsVL (shutdown) 0 +0.8 VVH (amplifier is active) 0.75 (V+) 5.5 VInput Bias Current of Enable Pin 50 pAIQSD 2 µA

POWER SUPPLYOperating Voltage Range 2.7 5.5 VQuiescent Current: OPA334, OPA335 IQ IO = 0 285 350 µA

Over Temperature 450 µAOPA2334, OPA2335 (total—two amplifiers) IO = 0 570 700 µAOver Temperature 900 µA

TEMPERATURE RANGESpecified Range –40 +125 °COperating Range –40 +150 °CStorage Range –65 +150 °CThermal Resistance θJA °C/W

SOT23-5, SOT23-6 Surface-Mount 200 °C/WMSOP-8, MSOP-10, SO-8 Surface-Mount 150 °C/W

NOTES: (1) 500-hour life test at 150°C demonstrated randomly distributed variation approximately equal to measurement repeatability of 1µV. (2) Device requiresone complete cycle to return to VOS accuracy.

4www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

TYPICAL CHARACTERISTICSAt TA = +25°C, VS = +5V, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.

OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION

Offset Voltage Drift (µV/°C)

Pop

ulat

ion

0

0.00

5

0.01

0

0.01

5

0.02

0

0.02

5

0.03

0

0.03

5

0.04

0

0.04

5

0.05

0

Absolute Value;Centered Around Zero

OFFSET VOLTAGE PRODUCTION DISTRIBUTION

Offset Voltage (µV)

–3.0

–2.7

–2.4

–2.1

–1.8

–1.5

–1.2

–0.9

–0.6

–0.3 0

0.3

0.6

0.9

1.2

1.5

1.8

2.1

2.4

2.7

3.0

Pop

ulat

ion

INPUT BIAS CURRENT vs COMMON-MODE VOLTAGEI

nput

Bia

s C

urre

nt

(pA

)

0

1200

1000

800

600

400

200

02.5 3.02.01.51.00.5

Common-Mode Voltage (V)

3.5

–40°C +25°C

+125°C

INPUT BIAS CURRENT vs TEMPERATURE

Inp

ut B

ias

Cur

rent

(p

A)

1000

100

10

Temperature (°C)

–40 40200–20 1201008060

QUIESCENT CURRENT (per channel)vs TEMPERATURE

Qui

esce

nt C

urre

nt (

µA)

–40

400

350

300

250

200

150

100

50

040200–20

Temperature (°C)

1201008060

VS = +5.5V

VS = +2.7V

OUTPUT VOLTAGE SWING vs OUTPUT CURRENT(V+)

(V+) – 1

(V–) + 1

(V–)0 2 4 6 8 10

Output Current (mA)

Out

put V

olta

ge S

win

g (V

) +125°C5.5V2.7V

+25°C

–40°C

+125°C

+25°C

–40°C

5www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

TYPICAL CHARACTERISTICS (Cont.)At TA = +25°C, VS = +5V, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.

LARGE-SIGNAL RESPONSE

Time (5µs/div)

Out

put V

olta

ge (

1V/d

iv)

G = –1CL = 300pF

SMALL-SIGNAL RESPONSE

Time (5µs/div)

Out

put V

olta

ge (

50m

V/d

iv)

G = +1CL = 50pF

OPEN-LOOP GAIN/PHASE vs FREQUENCY

AO

L (d

B)

140

120

100

80

60

40

20

0

–20

Pha

se (

°)

–80

–90

–100

–110

–120

–130

–140

–150

–160

Frequency (Hz)

0.1 10k1k100101 10M1M100k

Phase

Gain

POSITIVE OVER-VOLTAGE RECOVERY

Time (25µs/div)

200m

V/d

iv1V

/div

0

0

Input

Output100Ω

10kΩ

+2.5V

–2.5V

OPA335

NEGATIVE OVER-VOLTAGE RECOVERY

Time (25µs/div)

200m

V/d

iv1V

/div

0

0

Input

Output100Ω

10kΩ

+2.5V

–2.5V

OPA335

COMMON-MODE REJECTION vs FREQUENCY

Com

mon

-Mod

e R

ejec

tion

(dB

)

1

140

120

100

80

60

40

20

0

10k1k10010

Frequency (Hz)

10M1M100k

6www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

TYPICAL CHARACTERISTICS (Cont.)At TA = +25°C, VS = +5V, RL = 10kΩ connected to VS/2, and VOUT = VS /2, unless otherwise noted.

NOISE vs FREQUENCY

Noi

se (

nV/√

Hz)

1

1000

100

101k10010

Frequency (Hz)

100k10k

SAMPLING FREQUENCY vs TEMPERATURE

Sam

plin

g F

requ

ency

(kH

z)

–40

13

12

11

10

9

8–10 50 110 125

Temperature (°C)

20 80

SAMPLING FREQUENCY vs SUPPLY VOLTAGE

Fre

quen

cy (

kHz)

2.7

11.0

10.9

10.8

10.7

10.6

10.5

10.4

10.3

10.2

10.1

10.03.73.2 5.2 5.5

Supply Voltage (V)

4.74.2

SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE(VS = 2.7V to 5V)

Ove

rsho

ot (

%)

10

50

45

40

35

30

25

20

15

10

5

0100 1000

Load Capacitance (pF)

RL = 10kΩ

0.01Hz TO 10Hz NOISE

10s/div

400n

V/d

iv

POWER-SUPPLY REJECTION RATIO vs FREQUENCY

Pow

er-S

uppl

y R

ejec

tion

Rat

io (

dB)

140

120

100

80

60

40

20

0

Frequency (Hz)

10 1k100 1M100k10k

+PSRR

–PSRR

7www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

TYPICAL CHARACTERISTICS (Cont.)At TA = +25°C, VS = +5V, RL = 10kΩ connected to VS /2, and VOUT = VS /2, unless otherwise noted.

APPLICATIONS INFORMATIONThe OPA334 and OPA335 series op amps are unity-gainstable and free from unexpected output phase reversal. Theyuse auto-zeroing techniques to provide low offset voltageand very low drift over time and temperature.

Good layout practice mandates use of a 0.1µF capacitorplaced closely across the supply pins.

For lowest offset voltage and precision performance, circuitlayout and mechanical conditions should be optimized. Avoidtemperature gradients that create thermoelectric (Seebeck)effects in thermocouple junctions formed from connectingdissimilar conductors. These thermally-generated potentialscan be made to cancel by assuring that they are equal onboth input terminals.

• Use low thermoelectric-coefficient connections (avoid dis-similar metals).

• Thermally isolate components from power supplies orother heat-sources.

• Shield op amp and input circuitry from air currents, such ascooling fans.

Following these guidelines will reduce the likelihood of junc-tions being at different temperatures, which can cause ther-moelectric voltages of 0.1µV/°C or higher, depending onmaterials used.

OPERATING VOLTAGE

The OPA334 and OPA335 series op amps operate over apower-supply range of +2.7V to +5.5V (±1.35V to ±2.75V).Supply voltages higher than 7V (absolute maximum) canpermanently damage the amplifier. Parameters that varyover supply voltage or temperature are shown in the TypicalCharacteristics section of this data sheet.

OPA334 ENABLE FUNCTION

The enable/shutdown digital input is referenced to the V–supply voltage of the amp. A logic high enables the op amp. Avalid logic high is defined as > 75% of the total supply voltage.The valid logic high signal can be up to 5.5V above the negativesupply, independent of the positive supply voltage. A validlogic low is defined as < 0.8V above the V– supply pin. If dualor split power supplies are used, be sure that logic input signalsare properly referred to the negative supply voltage. TheEnable pin must be connected to a valid high or low voltage, ordriven, not left open circuit.

The logic input is a high-impedance CMOS input, with sepa-rate logic inputs provided on the dual version. For battery-operated applications, this feature can be used to greatlyreduce the average current and extend battery life.

The enable time is 150µs, which includes one full auto-zerocycle required by the amplifier to return to VOS accuracy.Prior to this time, the amplifier functions properly, but withunspecified offset voltage.

Disable time is 1µs. When disabled, the output assumes ahigh-impedance state. This allows the OPA334 to be oper-ated as a gated amplifier, or to have the output multiplexedonto a common analog output bus.

INPUT VOLTAGE

The input common-mode range extends from (V–) – 0.1V to(V+) – 1.5V. For normal operation, the inputs must be limitedto this range. The common-mode rejection ratio is only validwithin the valid input common-mode range. A lower supplyvoltage results in lower input common-mode range; there-fore, attention to these values must be given when selectingthe input bias voltage. For example, when operating on asingle 3V power supply, common-mode range is from 0.1Vbelow ground to half the power-supply voltage.

COMMON-MODE RANGE vs SUPPLY VOLTAGE

Com

mon

-Mod

e R

ange

(V

)

2.7

4.5

4.0

3.5

3.0

2.5

2.0

1.5

1.0

0.5

0

–0.53.73.2 5.2 5.5

Supply Voltage (V)

4.74.2

Minimum Common-Mode

Maximum Common-Mode

SETTLING TIME vs CLOSED-LOOP GAIN

Set

tling

Tim

e (µ

s)

1

100

10

110

Gain (V/V)

100

0.1%

0.01%

Unity-gainrequires onecomplete Auto-ZeroCycle—see text.

8www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

FIGURE 1. Input Current Protection.

5kΩ

OPA33510mA max

+5V

VIN

VOUT

IOVERLOAD

Current-limiting resistor required if input voltage exceeds supply rails by≥ 0.5V.

Normally, input bias current is approximately 70pA; however,input voltages exceeding the power supplies can causeexcessive current to flow in or out of the input pins. Momen-tary voltages greater than the power supply can be toleratedif the input current is limited to 10mA. This is easily accom-plished with an input resistor, as shown in Figure 1.

INTERNAL OFFSET CORRECTION

The OPA334 and OPA335 series op amps use an auto-zerotopology with a time-continuous 2MHz op amp in the signalpath. This amplifier is zero-corrected every 100µs using aproprietary technique. Upon power-up, the amplifier requiresone full auto-zero cycle of approximately 100µs to achievespecified VOS accuracy. Prior to this time, the amplifierfunctions properly but with unspecified offset voltage.

This design has remarkably little aliasing and noise. Zerocorrection occurs at a 10kHz rate, but there is virtually nofundamental noise energy present at that frequency. For allpractical purposes, any glitches have energy at 20MHz orhigher and are easily filtered, if required. Most applicationsare not sensitive to such high-frequency noise, and nofiltering is required.

Unity-gain operation demands that the auto-zero circuitrycorrect for common-mode rejection errors of the main ampli-fier. Because these errors can be larger than 0.01% of a full-scale input step change, one calibration cycle (100µs) can berequired to achieve full accuracy. This behavior is shown inthe typical characteristic section, see Settling Time vs Closed-Loop Gain.

ACHIEVING OUTPUT SWING TO THE OP AMP’SNEGATIVE RAIL

Some applications require output voltage swing from 0V to apositive full-scale voltage (such as +2.5V) with excellentaccuracy. With most single-supply op amps, problems arisewhen the output signal approaches 0V, near the lower output

FIGURE 2. Op Amp with Pull-Down Resistor to AchieveVOUT = Ground.

swing limit of a single-supply op amp. A good single-supplyop amp may swing close to single-supply ground, but will notreach ground. The output of the OPA334 or OPA335 can bemade to swing to ground, or slightly below, on a single-supply power source. To do so requires use of anotherresistor and an additional, more negative, power supply thanthe op amp’s negative supply. A pull-down resistor may beconnected between the output and the additional negativesupply to pull the output down below the value that the outputwould otherwise achieve, as shown in Figure 2.

The OPA334 and OPA335 have an output stage that allowsthe output voltage to be pulled to its negative supply rail, orslightly below using the above technique. This technique onlyworks with some types of output stages. The OPA334 andOPA335 have been characterized to perform well with thistechnique. Accuracy is excellent down to 0V and as low as–2mV. Limiting and non-linearity occurs below –2mV, butexcellent accuracy returns as the output is again drivenabove –2mV. Lowering the resistance of the pull-down resis-tor will allow the op amp to swing even further below thenegative rail. Resistances as low as 10kΩ can be used toachieve excellent accuracy down to –10mV.

LAYOUT GUIDELINES

Attention to good layout practices is always recommended.Keep traces short. When possible, use a PCB ground planewith surface-mount components placed as close to the de-vice pins as possible. Place a 0.1µF capacitor closely acrossthe supply pins. These guidelines should be applied through-out the analog circuit to improve performance and providebenefits such as reducing the EMI (electromagnetic-interfer-ence) susceptibility.

VOUT

RP = 40kΩ

Op Amp’s V– = Gnd

OPA335

VIN

V+ = +5V

–5VAdditionalNegativeSupply

9www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

FIGURE 3. Temperature Measurement Circuit.

+ +

+

– –

+

4.096V

0.1µF

+5V

Zero Adj.K-Type

Thermocouple40.7µV/°C

R2549Ω

R9150kΩ

R531.6kΩ

R16.04kΩ

R6200Ω

+5V

0.1µF

R22.94kΩ

VO

R360.4Ω

R46.04kΩ

OPA335

D1

REF3040

FIGURE 4. Auto-Zeroed Transimpedance Amplifier.

FIGURE 5. Single Op Amp Bridge Amplifier Circuits.

R1

VEX

VOUT

VREF

R1

OPA335RR

R R

+5V

a. 5V Supply Bridge Amplifier.

VEX = +2.5V

R1 = 105Ω

@ VS = 2.7V,VCMmax = 1.2V

VOUTOPA335

300ΩBridge

+2.7V

R2Select R1 so bridgeoutput ≤ VCMmax.

VREF

R2

b. 2.7V Supply Bridge Amplifier.

1MΩ

IIN R1

R2

C1

C240kΩ(1)

–5V

OPA343

OPA335

Photodiode

NOTE: (1) Optional pull-down resistor to allow below ground output swing.

+5V

+5V

b. Single Supply.

1MΩ

IIN R1

R2

+2.5V

OPA343

–2.5V

+2.5V

C1

C2–2.5V

OPA335

Photodiode

a. Split Supply.

10www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

FIGURE 7. Low-Side Current Measurement.

ADS1100

5VV

11.5kΩ

I2C

1kΩ RS

Load

(PGA Gain = 8)5V FS

50mVShunt

FS = 0.63V

G = 12.5

NOTE: (1) Pull-down resistor to allow accurate swing to 0V.

–5V

R3(1)

40kΩ

+5V

OPA335

FIGURE 6. Dual Op Amp IA Bridge Amplifier.

R2

–5V

VREF

R3(1)

40kΩ

G = 1 +R2

R1

R1R1

+5V

+5V

R2

1/2OPA2335

RRR R

VOUT

1/2OPA2335

NOTE: (1) Optional pull-down resistor to allow accurate swing to 0V.

11www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

FIGURE 8. High Dynamic Range Transimpedance Amplifier.

–5V

R2(1)

2kΩ

R14.12kΩ

+5V

R3100Ω

VOUT

≈ 1MHz BandwidthVOS ≈ 10µV

OPA353

C156pF

C20.1µF

C31nF

–5V

R5(1)

40kΩ

+5V

R649.9kΩ

R4100kΩ

OPA335

C410nF

Photodiode≈ 2pF

C60.1µF

C510nF

R71kΩPhotodiode

Bias

C71µF

NOTE: (1) Pull-down resistors to allow accurate swing to 0V.

12www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

PACKAGE DRAWINGS

DBV (R-PDSO-G6) PLASTIC SMALL-OUTLINE

0,10

M0,200,95

0 –8

0,25

0,550,35

Gage Plane

0,15 NOM

4073253-5/G 01/02

2,603,00

0,500,25

1,501,70

46

31

2,803,00

1,450,95

0,05 MIN

Seating Plane

6X

NOTES: A. All linear dimensions are in millimeters.B. This drawing is subject to change without notice.C. Body dimensions do not include mold flash or protrusion.D. Leads 1, 2, 3 may be wider than leads 4, 5, 6 for package orientation.

13www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

DGS (S-PDSO-G10) PLASTIC SMALL-OUTLINE PACKAGE

0,690,41

0,25

0,15 NOM

Gage Plane

4073272/B 08/01

4,98

0,17

6

3,054,782,95

10

5

3,052,95

1

0,27

0,150,05

1,07 MAX

Seating Plane

0,10

0,50 M0,08

0°–6°

NOTES: A. All linear dimensions are in millimeters.B. This drawing is subject to change without notice.C. Body dimensions do not include mold flash or protrusion.A. Falls within JEDEC MO-187

PACKAGE DRAWINGS (Cont.)

14www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

PACKAGE DRAWINGS (Cont.)

DBV (R-PDSO-G5) PLASTIC SMALL-OUTLINE

0,10

M0,200,95

0° – 8°

0,25

0,350,55

Gage Plane

0,15 NOM

4073253-4/G 01/02

2,603,00

0,500,30

1,501,70

45

31

2,803,00

0,951,45

0,05 MIN

Seating Plane

NOTES: A. All linear dimensions are in millimeters.B. This drawing is subject to change without notice.C. Body dimensions do not include mold flash or protrusion.D. Falls within JEDEC MO-178

15www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

PACKAGE DRAWINGS (Cont.)

D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE8 PINS SHOWN

8

0.197(5,00)

A MAX

A MIN(4,80)0.189 0.337

(8,55)

(8,75)0.344

14

0.386(9,80)

(10,00)0.394

16DIM

PINS **

4040047/E 09/01

0.069 (1,75) MAX

Seating Plane

0.004 (0,10)0.010 (0,25)

0.010 (0,25)

0.016 (0,40)0.044 (1,12)

0.244 (6,20)0.228 (5,80)

0.020 (0,51)0.014 (0,35)

1 4

8 5

0.150 (3,81)0.157 (4,00)

0.008 (0,20) NOM

0°– 8°

Gage Plane

A

0.004 (0,10)

0.010 (0,25)0.050 (1,27)

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).D. Falls within JEDEC MS-012

16www.ti.com

OPA334, OPA2334, OPA335, OPA2335SBOS245D

PACKAGE DRAWINGS (Cont.)

DGK (R-PDSO-G8) PLASTIC SMALL-OUTLINE PACKAGE

0,690,41

0,25

0,15 NOM

Gage Plane

4073329/C 08/01

4,98

0,25

5

3,054,782,95

8

4

3,052,95

1

0,38

1,07 MAX

Seating Plane

0,65 M0,08

0°–6°

0,100,150,05

NOTES: A. All linear dimensions are in millimeters.B. This drawing is subject to change without notice.C. Body dimensions do not include mold flash or protrusion.D. Falls within JEDEC MO-187

PACKAGING INFORMATION

Orderable Device Status (1) PackageType

PackageDrawing

Pins PackageQty

Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)

OPA2334AIDGSR ACTIVE MSOP DGS 10 2500 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA2334AIDGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA2334AIDGST ACTIVE MSOP DGS 10 250 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA2335AID ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA2335AIDGKR ACTIVE MSOP DGK 8 2500 TBD CU NIPDAU Level-1-235C-UNLIM

OPA2335AIDGKT ACTIVE MSOP DGK 8 250 TBD CU NIPDAU Level-1-235C-UNLIM

OPA2335AIDR ACTIVE SOIC D 8 2500 TBD CU NIPDAU Level-3-235C-168 HR

OPA334AIDBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA334AIDBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA334AIDBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA335AID ACTIVE SOIC D 8 100 TBD CU NIPDAU Level-3-235C-168 HR

OPA335AIDBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA335AIDBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA335AIDBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA335AIDBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS &no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR

OPA335AIDR ACTIVE SOIC D 8 2500 TBD CU NIPDAU Level-3-235C-168 HR

(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part ina new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please checkhttp://www.ti.com/productcontent for the latest availability information and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirementsfor all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be solderedat high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flameretardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak soldertemperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it isprovided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to theaccuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to takereasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on

PACKAGE OPTION ADDENDUM

www.ti.com 13-Sep-2005

Addendum-Page 1

incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limitedinformation may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TIto Customer on an annual basis.

PACKAGE OPTION ADDENDUM

www.ti.com 13-Sep-2005

Addendum-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,enhancements, improvements, and other changes to its products and services at any time and to discontinueany product or service without notice. Customers should obtain the latest relevant information before placingorders and should verify that such information is current and complete. All products are sold subject to TI’s termsand conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale inaccordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TIdeems necessary to support this warranty. Except where mandated by government requirements, testing of allparameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible fortheir products and applications using TI components. To minimize the risks associated with customer productsand applications, customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or processin which TI products or services are used. Information published by TI regarding third-party products or servicesdoes not constitute a license from TI to use such products or services or a warranty or endorsement thereof.Use of such information may require a license from a third party under the patents or other intellectual propertyof the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of information in TI data books or data sheets is permissible only if reproduction is withoutalteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproductionof this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable forsuch altered documentation.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for thatproduct or service voids all express and any implied warranties for the associated TI product or service andis an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Following are URLs where you can obtain information on other Texas Instruments products and applicationsolutions:

Products Applications

Amplifiers amplifier.ti.com Audio www.ti.com/audio

Data Converters dataconverter.ti.com Automotive www.ti.com/automotive

DSP dsp.ti.com Broadband www.ti.com/broadband

Interface interface.ti.com Digital Control www.ti.com/digitalcontrol

Logic logic.ti.com Military www.ti.com/military

Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork

Microcontrollers microcontroller.ti.com Security www.ti.com/security

Telephony www.ti.com/telephony

Video & Imaging www.ti.com/video

Wireless www.ti.com/wireless

Mailing Address: Texas Instruments

Post Office Box 655303 Dallas, Texas 75265

Copyright 2005, Texas Instruments Incorporated