OMFA - OPS Moduledc.winmate.com.tw/_downloadCenter/2016/OPSMoudle/OMFA-OPS...Freescale iMX6 Quad...

OMFA - OPS Module

Digital signage display Optional Pluggable Specification (OPS) enables

easy integration of a digital signage computing system or a pluggable

module into the display panel.

Freescale iMX6 Quad Core 1GHz Processor, DDR3 1GB system memory,

one USB2.0 OTG, two USB2.0 host, two audio jacks for microphone,

line-in and line-out, optional Wi-Fi or 3G.

User Manual Version 1.0

Manual Number: 917111171004

User Manual II

Preface

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer.

Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer We reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. We make no representation or warranty that such application will be suitable for the specified use without further testing or modification.

Warranty We warrant that each of its products will be free from material and workmanship defects for a period of one year from the invoice date. (Standard is one year, extended warranty will need to discuss with our sales representatives. If the customer discovers a defect, we will, at its option, repair or replace the defective product at no charge to the customer, provided it is returned during the warranty period of one year, with transportation charges prepaid. The returned product must be properly packaged in its original packaging to obtain warranty service. If the serial number and the product shipping data differ by over 30 days, the in-warranty service will be made according to the shipping date. In the serial numbers the third and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g., with A for October, B for November and C for December). For example, the serial number 1W16Axxxxxxxx means October of year 2016.

User Manual III

Packing List Before using this product, please make sure that all the items listed below are present in your package:

OMFA - OPS Module User Manual & Driver CD

If any of these items are missing or damaged, contact your distributor or sales representative immediately.

Ordering Information

Standard Freescale Cortex™-A9 i.MX 6 Series Quad Core 1GHz RAM : DDR3 1 GB Storage : On board 16GB eMMC OS: Android 4.4

Optional 1 x 2.5" SATA HDD/SSD Wi-Fi : (802.11 b/g/n) or 3G

Customer Service We provide a service guide as below for any problem by the following steps: First, contact your distributor, sales representative, or our customer service center for technical support if you need additional assistance. You need to prepare the following information before you call:

Product serial number Peripheral attachments Software (OS, version, application software, etc.) Detailed problem description The exact wording of any error messages

In addition, free technical support is available from our engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. Please do not hesitate to call or e-mail us.

Advisory Conventions

Four types of advisories are used throughout the user manual to provide helpful information

or to alert you to the potential for hardware damage or personal injury. These are Notes,

Important, Cautions, and Warnings. The following is an example of each type of advisory.

NOTE:

A note is used to emphasize helpful information

IMPORTANT:

An important note indicates information that is important for you to know.

User Manual IV

CAUTION

A Caution alert indicates potential damage to hardware and explains how to

avoid the potential problem.

WARNING!

An Electrical Shock Warning indicates the potential harm from electrical

hazards and how to avoid the potential problem.

Safety Precautions

WARNING!

Always completely disconnect the power from OPS module whenever

you work with the hardware. Do not make connections while the

power is on. Sensitive electronic components can be damaged by

sudden power surges.

CAUTION

Always ground yourself to remove any static charge before touching

the CPU card. Modern electronic devices are very sensitive to static

electric charges. As a safety precaution, use a grounding wrist strap at

all times. Place all electronic components in a static-dissipative surface

or static-shielded bag when they are not in the chassis.

Safety and Warranty

1. Please read these safety instructions carefully.

2. Please keep this user manual for later reference.

3. Please disconnect this equipment from any AC outlet before cleaning. Do not use

liquid or spray detergents for cleaning. Use a damp cloth.

4. For pluggable equipment, the power outlet must be installed near the equipment

and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it

fall could cause damage.

7. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

User Manual V

8. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

9. All cautions and warnings on the equipment should be noted.

10. If the equipment is not used for a long time, disconnect it from the power source to

avoid damage by transient over-voltage.

11. If any of the following situations arises, get the equipment checked by service

personnel:

A. The power cord or plug is damaged.

B. Liquid has penetrated into the equipment.

C. The equipment has been exposed to moisture.

D. The equipment does not work well, or you cannot get it to work according to

the user’s manual.

E. The equipment has been dropped and damaged.

F. The equipment has obvious signs of breakage.

Revision History

Version Date Note Author

1.0 14-Mar-2016 Initial release Austin Chang, edited by Anna Kiseleva

User Manual VI

Contents PREFACE ..................................................................................................................................................... I

CHAPTER 1 GENERAL INFORMATION ........................................................................................................ 2

1.1 INTRODUCTION .......................................................................................................................................... 2

1.2 FEATURES ................................................................................................................................................. 2

1.3 SPECIFICATION ........................................................................................................................................... 3

1.4 PHYSICAL DESCRIPTION ............................................................................................................................... 4

1.4.1 Dimensions .................................................................................................................................... 4

1.4.2 Appearance ................................................................................................................................... 4

CHAPTER 2 HARDWARE INSTALLATION ..................................................................................................... 7

2.1 MOTHERBOARD COMPONENTS ..................................................................................................................... 7

2.1.1 Front Side ...................................................................................................................................... 7

2.1.2 Rear Side ........................................................................................................................................ 7

2.1.3 I/O Side .......................................................................................................................................... 8

2.2 CONNECTOR PIN ASSIGNMENTS .................................................................................................................... 8

2.2.1 Front Side ...................................................................................................................................... 9

2.2.2 Rear Side ...................................................................................................................................... 11

2.2.3 I/O Side ........................................................................................................................................ 12

2.3 HARDWARE MODIFICATION ........................................................................................................................ 17

2.3.1 HDD/SSD Installation ................................................................................................................... 17

2.3.2 SIM Card Installation ................................................................................................................... 18

2.3.3 Other Internal Parts ..................................................................................................................... 19

CHAPTER 3 SOFTWARE UPDATE .............................................................................................................. 22

3.1 ANDROID DEBUG BRIDGE (ADB) DRIVER INSTALLATION .................................................................................. 22

3.1.1 Disabling Driver Signature on Windows 8 ................................................................................... 23

3.1.2 ADB Driver Installation ................................................................................................................ 28

3.2 INSTALLING ANDROID DEBUG BRIDGE (ADB) ................................................................................................ 31

3.3 IMAGE TOOL DOWNLOAD .......................................................................................................................... 33

3.4 OS IMAGE UPDATE ................................................................................................................................... 33

3.5 OTA UPDATE GUIDE ................................................................................................................................. 40

CHAPTER 4 TECHNICAL SUPPORT DOCUMENTS ...................................................................................... 45

4.1 ANDROID SDK ......................................................................................................................................... 45

OMFA OPS Pluggable Module General Information

User Manual 1

General Information This chapter includes OMFA - OPS Module

background information.


User Manual 2

Chapter 1 General Information

This chapter includes OMFA - OPS module background information such as features, hardware specification, dimensions and appearance.

1.1 Introduction

Thank you for choosing the OMFA - OPS Module. Digital signage display Optional

Pluggable Specification (OPS) enables easy integration of a digital signage computing

system or a pluggable module into the display panel. The module is powered by

Freescale iMX6 Quad Core 1GHz processor that allows running on Android 4.4 operating

system. Android provides many options for easy software integration.

Open Pluggable Specification (OPS) module that can be installed into the display panel

through a single and standard interfacing based on the 80 pin JAE plug and receptacle

connectors. The power supply to the motherboard together with the defined feature

interfaces are being routed through the set of connectors, and provide a functional

system level computing solution for digital signage.

There is an advanced full set of I/O ports including one USB2.0 OTG, two USB2.0 host,

two audio jacks for microphone, line-in and line-out. The current model allows adding

Wi-Fi or 3G models for better connectivity and information exchange.

1.2 Features

OMFA - OPS Module has the following features:

Freescale iMX6 Quad Core 1GHz processor

Android 4.4

DDR3 1GB system memory

Integrated graphics

1 x Power Button, 1 x Reset Button, 2 x USB2.0 Host, 1 x USB 2.0 OTG, 2 x Audio

Jack, 1 x RJ45

Wi-Fi / 3G modules (optional)


User Manual 3

1.3 Specification

System Specification:

CPU Freescale Cortex™-A9 i.MX 6 Series Quad Core 1GHz

System Memory DDR3 1GB

OS Android 4.4

Storage On board 16GB eMMC, 1 x 2.5" SATA HDD/SSD

Graphic Chipset Integrated Graphics

Ethernet Gigabit Ethernet LAN

Audio Mic-in / Headphone

I/O Interface:

Front

1 x Power Button

1 x Reset button

2 x USB 2.0 Host

1 x USB 2.0 OTG

2 x Audio Jack (Line-in/ Line-out)

1 x RJ45

Rear (OPS Interconnector) 1 x JAE 80-Pin connector (OPS Standard)

Power Requirements:

Power Consumption 10W (burn in test)

Input Voltage 12V~19V DC in (via OPS interconnection)

Mechanical Dimensions:

Dimensions (W x H x D) 200 x 30 x 118mm (OPS compliant)

Environment:

Operating Temperature -10°C to 60°C

Operating Humidity 30%~ 90% (non-condensing, RH)

Certification

Electromagnetic CE, FCC

*Wireless Communication:

*Wi-Fi USB Wi-Fi Module

*3G Mini PCle 3G Module

*optional


User Manual 4

1.4 Physical Description

1.4.1 Dimensions

119 x 30 x 200 (unit: mm)

1.4.2 Appearance

Front Side


User Manual 5

Rear Side

OMFA OPS Pluggable Module Hardware Installation

User Manual 6

Hardware Installation This chapter provides information on how to use

jumpers and connectors on the motherboard, and

OMFA - OPS module hardware installation

instruction.


User Manual 7

Chapter 2 Hardware Installation

This chapter provides information on how to use jumpers and connectors on the

OMFA motherboard. Be cautious while working with these modules. Carefully read

the content of this chapter in order to avoid any damages.

2.1 Motherboard Components

2.1.1 Front Side

2.1.2 Rear Side

SW1

USB 2.0

Mini-PCIE

Half Card


User Manual 8

2.1.3 I/O Side

2.1.3.1 Top

2.1.3.2 Bottom

2.2 Connector Pin Assignments

This section explains how to set jumpers for correct configuration of the

motherboard.


User Manual 9

NOTE:

A pair of needle nose pliers may be helpful when working with jumpers.

If you have any doubts about the best hardware configuration for your

application, contact your local distributor or sales representative before

you make any changes. Generally, you simply need a standard cable to

make most connections.

The jumper setting diagram is shown below. When the jumper cap is placed on both

pins, the jumper is SHORT. The illustration below shows a 3-pin jumper; pins 1 and 2

are short. If you remove the jumper cap, the jumper is OPEN.

CAUTION

To avoid damaging the module, always turn off the power supply

before setting jumpers or clearing CMOS.

2.2.1 Front Side

Label Function Note

BT1 Backup Battery Wafer 1x2p P:1.25mm SMD 90

CN4 USB I/O Port Wafer 1x4p P:1.0mm 180° white color

CN18 SPI I/F Port Wafer 1x6p P:1.0mm SMD 180° white color

CN35 RS232 Wafer 1x4p P:1.0mm SMD 180° white color

CN37 Debug Port Wafer 1x6p P:1.0mm SMD 180° white color

BT1: Backup Battery

Pin № Name

1 GND

2 BAT

1

2

3


User Manual 10

CN4: USB I/O Port

CN18: SPI I/F Port

CN35: RS232

CN37: Debug Port

Pin № Name

1 WIFI_PWR_5V

2 WIFI_USB_DM

3 WIFI_USB_DP

4 GND

Pin № Name

1 +V3.3S

2 ECSPI3_MISO

3 ECSPI3_MOSI

4 ECSPI3_CS1

5 ECSPI3_SCLK

6 GND

Pin № Name

1 VUART1

2 RS232_3_TX

3 RS232_3_RX

4 GND

Pin № Name

1 TXD232

2 NC

3 NC

4 RXD232

5 DBUG_5V

6 GND


User Manual 11

2.2.2 Rear Side

Label Function Note

CN5 Micro-SIM Card Connector C-MSM01S030R

CN9 Min-PCIe Connector AS0B226-S40Q-7H

CN5: Micro-SIM Card Connector

CN9: Mini-PCIe Connector

Pin № Name Pin № Name

1 PCIE_WAKE# 2 PCIE_3V3

3 NC 4 GND

5 NC 6 PCIE_1V5

7 NC (*GND) 8 VREG_USIM

9 GND 10 SIM_DAT

11 PCIE_CLK1_N 12 SIM_CLK

Pin № Name

C1 VREG_USIM

C2 USIM_RST

C3 USIM_CLK

C5 GND

C6 USIM_VPP

C7 USIM_DAT

SW USIM_DET (Default High, Active Low)

G1 NC

G2 NC

G3 GND

G4 GND


User Manual 12

13 PCIE_CLK1_P 14 SIM_RST

15 GND 16 SIM_VPP

17 NC 18 GND

19 NC 20 PCIE_PWR_EN

21 GND 22 PCIE_RST_N

23 PCIE_RXM_1 24 NC (*PCIE_3V3)

25 PCIE_RXP_1 26 GND

27 GND 28 PCIE_1V5

29 GND 30 NC

31 PCIE_TXM_1 32 NC

33 PCIE_TXP_1 34 GND

35 GND 36 PCIE_USB_DM

37 GND 38 PCIE_USB_DP

39 PCIE_3V3 40 GND

41 PCIE_3V3 42 NC

43 GND 44 M7304_DPR

45 NC 46 NC

47 NC 48 PCIE_1V5

49 NC 50 GND

51 NC 52 PCIE_3V3

*optional

2.2.3 I/O Side

2.4.3.1 Top

Label Function Note

CN7 Line Out WTJ-035-82I Green

CN8 Mic In WTJ-035-82I PINK

CN21 Dual USB Type A Connector SUYIN 020122MR008S541ZL

CN30 Micro SD Slot 81CSD03S030R

CN32 Micro USB Port 22UBH-051-120L

LAN1 RJ45 Support 10/100/1000 Mbps LAN RT7-174AAM1A UDE

SW1 Power Key TC003-N11AABUBXX-RK WITH LED

SW4 Reset Key TSVB-31L 3mm 90°


User Manual 13

CN7: Line Out

CN8: Mic In

CN21: Dual USB Type A Connector

Pin № Name

1 HP_LIN

2 HP_RIN

3 GND

4 HEADPHONE_DET

5 GND

6 GND

7 NC

8 NC

Pin № Name

1 MIC_IN-

2 MIC_IN+

3 GND

4 MICROPHONE_DET

5 GND

6 GND

7 NC

8 NC

Pin № Name

1 VUSB_VBUS0

2 EXT_USB0_DM

3 EXT_USB0_DP

4 GND

5 VUSB_VBUS1

6 EXT_USB1_DM

7 EXT_USB1_DP

8 GND


User Manual 14

CN30: Micro SD Slot

CN32: Micro USB Port

LAN1: RJ45 Support 10/100/1000 Mbps

Pin № Name

1 SD3_DATA2

2 SD3_DATA 3

3 SD3_CMD

4 SD_3V3

5 SD3_CLK

6 GND

7 SD3_DATA0

8 SD3_DATA1

CD SD_CD#


1 VUSB_VOTG 2 USB_OTG_CON_DN

3 USB_OTG_CON_DP 4 USB_OTG_ID

5 GND 6 GND

7 GND 8 GND

9 GND


1 MDI0_IN+ 2 MDI0_IN-


5 NC 6 LAN1_DGND



11 +V3.3S 12 LAN1_ACTIVE_Y

13 LAN1_1000_

O

14 LAN1_100_10_G

15 GND 16 GND


User Manual 15

SW1: Power Key

SW4: Reset Key

2.4.3.2 Bottom

Label Function Note

CN1 OPS Connector None

CN3 SATA HDD iSATA Conn LD2722F-S4GL6 DIP 90°

CN1: OPS Connector


1 DDP_3N 2 DDP_3P

3 GND 4 DDP_2N

5 DDP_2P 6 GND

Pin № Name

1 GND

2 GND

3 CPUPWRON

4 CPUPWRON

5 GND

6 +V3.3S

Pin № Name

1 PM_SYSRST#

2 GND

3 GND

4 GND


User Manual 16

7 DDP_1N 8 DDP_1P

9 GND 10 DDP_0N

11 DDP_0P 12 GND

13 DDP_AUXN 14 DDP_AUXP

15 DDP_HPD 16 GND

17 TMDS_CLK- 18 TMDS_CLK+

19 GND 20 TMDS0

21 TMDS0+ 22 GND

23 TMDS1- 24 TMDS1+

25 GND 26 TMDS2-

27 TMDS2+ 28 GND

29 H_DAT_OUT 30 H_CLK_OUT

31 HP_DET_OUT 32 GND

33 DC_IN 34 DC_IN

35 DC_IN 36 DC_IN

37 DC_IN 38 DC_IN

39 DC_IN 40 DC_IN

41 RSVD 42 RSVD

43 RSVD 44 RSVD

45 RSVD 46 RSVD

47 RSVD 48 RSVD

49 RSVD 50 CB_SYS_FAN

51 COM_RXD 52 COM_TXD

53 GND 54 StdA_SSRX

55 StdA_SSRX+ 56 GND

57 StdA_SSTX- 58 StdA_SSTX+

59 GND 60 USB_PN2

61 USB_PP2 62 GND

63 USB_PN1 64 USB_PP1

65 GND 66 USB_PN0

67 USB_PP0 68 GND

69 REAR_L 70 REAR_R

71 HDMI_CEC_OUT 72 PB_DET

73 PS_ON# 74 PWR_STATUS

75 GND 76 GND

77 GND 78 GND

79 GND 80 GND


User Manual 17

CN3: SATA HDD


1 GND 2 SATA_TXP0

3 SATA_TXN0 4 GND

5 SATA_RXN0 6 SATA_RXP0

7 GND 8 SATA_3V3

9 SATA_3V3 10 SATA_3V3

11 GND 12 GND

13 GND 14 +V5S

15 +V5S 16 +V5S

17 GND 18 NC

19 GND 20 NC

21 NC 22 NC

2.3 Hardware Modification

2.3.1 HDD/SSD Installation

1. Disconnect OPS module from the power source.

WARNING!

Switch off the power and unplug the power cord. Each time the

OPS Module is serviced, users should be aware of this condition.

2. Loosen two Phillips M3 x 4 flathead black screws on the I/O side.


User Manual 18

3. Open the cover door.

4. Carefully pull out the 2.5” hard disk bay.

5. Exchange with the new hard disk. Be sure to check the orientation of the

hard disk is correct.

6. When finished, insert the cover door back and carefully tighten two Phillips

M3 x 4 flathead black screws.

2.3.2 SIM Card Installation


WARNING!



2. Loosen two Phillips M3 x 4 flathead black screws on the rear side.

3. Pull the cover lid up.


User Manual 19

4. Carefully insert the SIM card to the SIM card slot. Be sure to check the

orientation of the SIM-card is correct.

6. When finished, insert the cover door back and carefully tighten two

Phillips M3 x 4 flathead black screws.

2.3.3 Other Internal Parts


WARNING!




User Manual 20

2. Loosen the four Phillips M3 x 5 truss head silver screws on the top cover,

3. Remove the top cover.

4. Make all necessary modifications.

5. When finished, insert the cover door back and carefully tighten four

Phillips M3 x 5 truss head silver screws.

OMFA OPS Pluggable Module Software Update

User Manual 21

Software Update This chapter contains software update guide

for OMFA – OPS Module.


User Manual 22

Chapter 3 Software Update

This chapter contains software update guide for OMFA Board. With this tool you can

upgrade the system without losing previous installed APPs and data. All the

programming guides can be found in the driver CD included in the package

3.1 Android Debug Bridge (ADB) Driver Installation

You can find USB_OTG_driver in the following locations:

CDM v2.08.28 Certified\ftdibus.inf

CDM v2.08.28 Certified\ftdiport.inf

You need to connect OMFA - OPS Module to the computer with the USB 2.0 cable.

When using a USB cable (not supplied with OMFA – OPS Module), verify that the

cable or cable packaging bears the “Certified USB™” mark (see below) to guarantee

USB 2.0 compliance.

*I/O settings on the picture are for demonstration purposes only. Your I/O may vary

from the picture above.

IMPORTANT:

If your computer is running on Windows Embedded 8 Standard or

Windows 8.1 Industry Pro OS system, you need to disable driver

signature.

For Win XP / Win 7 skip disabling driver signature section, and

directly proceed to ADB driver installation.


User Manual 23

3.1.1 Disabling Driver Signature on Windows 8

Step 1 Hold down the Windows key on your keyboard and press the letter C to open

the Charm menu, and then click the gear icon (Settings).

Step 2 Click Change PC Settings.

Step 3 Click General.

Step 4 Under Advanced Startup, click Restart Now.


User Manual 24

NOTE: In Windows 8.1, the ‘Restart Now’ button has moved to ‘PC Setting -> Update

& Recovery -> Recovery.’


User Manual 25

Step 5 After restarting, click Troubleshoot.

Step 6 Click Advanced Options.


User Manual 26

Step 7 Click Windows Startup Settings.

Step 8 Click Restart.

Step 9 After restarting your computer a second time, choose Disable driver signature

enforcement from the list by typing the number 7 on your keyboard.


User Manual 27

Your computer will restart automatically.

Step 10 After restarting, you will be able to install the ADB drivers normally; however,

Windows will display a warning message. When the warning appears, click Install this

driver software anyway. If you are unfamiliar with installing drivers, check out our

Installing ADB driver tutorial for a step by step guide.

NOTE:

The next time you restart your computer, driver signature

enforcement will be in effect again. You will have to repeat this

process for any new boards. If you have multiple boards to use with

the same computer, we recommend installing the drivers for each one

before you shut down or restart your computer.


User Manual 28

3.1.2 ADB Driver Installation

Step 1 Confirm whether the USB device was found by the system.

Device Manager > 120A > Other devices > FA33_Taurus > Update Driver Software

Step 2 In the Update Driver Software window choose Browse my computer for

driver software.

Step 3 Select Let me pick from a list of device drivers on my computer. Click Next.


User Manual 29

Step 4 Select from your computer

Step 5 In the Update driver software window, click show All Devices and then click

Next.

Step 6 The system is looking for the driver folder. Click Browse.


User Manual 30

Step 7 Select the driver for your OS system. Click Open.

Step 8 Windows Security window will pop up. This message is used to confirm

whether the user wants to install the driver. Select Install this driver software

anyway to continue.


User Manual 31

Step 9 When the installation is successfully completed you will see Android ADB

Interface driver in the Update Driver Software window. Now adb debug can be

carried out.

3.2 Installing Android Debug Bridge (ADB)

For detailed Android Debug Bridge (ADB) information refer to Android Developers

Platform: http://developer.android.com/tools/help/adb.html .

http://developer.android.com/tools/help/adb.html


User Manual 32

Step 1

Decompress adb.zip. Open ADB terminal and move into the adb archive.

ADB Terminal window

Step 2

Connect FA33 motherboard to the computer via USB. FA33 will ask you to confirm

USB debugging. Tap OK.

After ADB connection established, install APP or check system log via adb.


User Manual 33

3.3 Image Tool Download

Download the latest version of OS Image Tool update guide at Winmate Download

Center:

http://www.winmate.com.tw/ > Support > Download Center > SBC > OMFA > OS

Image

3.4 OS Image Update

Step 1 Decompress the archive FSL_MFG_TOOL_WM.zip

Step 2 Go to the directory “FSL_MFG_TOOL_WM\Profiles\MX6Q Linux

Update\OS Firmware\files\android”.

http://www.winmate.com.tw/


User Manual 34

Step 3 Move the following items to one folder: the u-boot-6q.bin, boot.img,

system.img, userdata_img.tar.gz and recovery.img

Step 4 In FSL_MFG_TOOL_WM folder that you decompressed in Step 1 click

“MfgTool2.exe”.

MfgTool_MultiPanel window pops up.


User Manual 35

Step 5 Go to the main APPS screen > Settings

Step 6 Settings > About tablet

Step 7 Settings > About tablet > Additional system updates


User Manual 36

Step 8 Warning menu pops up. Confirm the system update by clicking YES.

NOTE:

The location of OTG connector is shown on the picture below:

IMPORTANT:

Assure OTG and power already connected. Do not disconnect the OTG

from the source of power while system is updating.


User Manual 37


User Manual 38

Step 9 Enter the hint number 1655 to confirm the update and click OK.

Step 10 In the dialog click Yes to shut down and restart the system.

Step 11 After the system reboot you will be able to see the system change.

No Device Connected > HID-compliant


User Manual 39

Step 12 Click Start to upgrade the system.

Step 13 After the successful update the screen is shown as below:


User Manual 40

3.5 OTA Update Guide

OTA is a tool which can help you to update OS image. To receive Android OS image

file contact our sales representatives. Once you get the image file follow the

guideline below.

Step 1 Copy image files ota_FA33_X_X_X_X.zip and FA33_X_X_X_X. md5 and to

micro SD card.

Step 2 Insert micro SD card to the slot in the HMI device. In the APPs menu tap OTA

Image Upd.

Step 3 The system is checking OTA File. It may take some time.

Step 4 Tap Update Image


User Manual 41

Step 5 Make sure the file founded by the system is image update file.

Tap OK.

Step 6 Tap OK. Make sure the battery level is at least 50%.


User Manual 42

Step 7 Tap OK.

IMPORTANT:

Do not disconnect the power source!

Do not remove the battery!

Step 8 After update the system will automatically restart.


User Manual 43

OMFA OPS Pluggable Module Technical Support Documents

User Manual 44

Technical Support Documents This chapter contains directory to software

development kit (SDK) and other technical

support documents.

OMFA OPS Pluggable Module Technical Support Documents

User Manual 45

Chapter 4 Technical Support Documents

This chapter includes technical support documents and software developing kit (SDK).

If any problem occurs immediately contact us.

4.1 Android SDK

Download SDK from Winmate Download Center or Winmate Partner Portal.

1. Winmate Download Center

http://www.winmate.com.tw/ > Support > Download Center > OPS Module > OMFA

> Android SDK

2. Winmate Partner Portal

http://www.winmate.com.tw/ > Support > Partner Portal > Public Documents > OPS

Module > OMFA



46

Winmate Inc.

9F, No.111-6, Shing-De Rd., San-Chung City,

Taipei 241, Taiwan, R.O.C

Tel: 886-2-8511-0288

Fax: 886-2-8511-0211

Email: [email protected]

Official website: http://www.winmate.com.tw


OMFA - OPS Moduledc.winmate.com.tw/_downloadCenter/2016/OPSMoudle/OMFA-OPS...Freescale iMX6 Quad...

Documents

Transcript of OMFA - OPS Moduledc.winmate.com.tw/_downloadCenter/2016/OPSMoudle/OMFA-OPS...Freescale iMX6 Quad...