Nutritional Performance and Protection · Micronutrient deficiencies usually occur when plants are...

Nutritional Performanceand Protection

www.bw-fusion.com

BW-Balance Chelated Micronutrients Solution

BALANCE delivers an optimized ratio of micronutrients for crops under high production demand. It reduces effects of stressful conditions that can decrease yield.

It’s formulated for use with fertilizer solutions as a supplement to a well-balanced fertilizer program. Including BALANCE in fertilizer applications before or at planting delivers the most benefit, since effects of micronutrient deficiencies are most damaging to young plants.

BENEFITS OF BW BALANCE• Broad spectrum of micronutrients• Corrects for micronutrient deficiencies in soil• Meets crop reproductive micronutrient needs to maximize yield• Chelated for fast, easy mixing• Minimizes stress-induced crop damage and premature ripening• Easy to use in nearly any foliar or pesticide application

APPLICATION INSTRUCTIONSFoliar Spray ApplicationsFor foliar spraying with a conventional sprayer, use a minimum of 20 gallons of water per acre per quart of BALANCE. A maximum of 1 quart per acre is recommended if foliar spraying BALANCE with low-volume equipment. Burning may occur in low-volume spray applications with little water. Spray when the crop is in an active growing stage after irrigation or rainfall for best results. Early mornings or late afternoon spray application is recommended.Vegetables: Incorporate BALANCE into the normal spray program, applying 1/2 to 1 quart per acre each spray.Field Crops: Apply 1 quart per acre when plants are young. This is the time when the most severe deficiencies occur.Tree and Vine Crops: Split applications are most beneficial and recommended. Apply 1 quart per 125 gallons of spray mixture. If using concentrated spray, increase the concentration in direct proportion to the dilution. It’s possible to split the above amount into several applications.

Aerial ApplicationsConsult an agronomist for application rates and dilutions.

Soil ApplicationsBALANCE is recommended for use on all types of soils using sprinkler, drip, or band application. Dilute prior to use for uniform coverage. BALANCE can be incorporated into liquid fertilizers or applied separately. Apply using the following rates if you do not have a leaf or soil analysis:Maintenance Application - 1 quart per acre.Moderate Deficiency - 2 to 3 quarts per acre.Severe Deficiency - 4 quarts per acre.

PLANT NUTRIENT FUNCTIONSThe primary benefits of the nutrients in BALANCE include:

Boron: Vital to new growth and essential for pollination and seed production. Also enhances nitrogen uptake and utilization.

Copper: Activates enzymes to convert amino acids to proteins, enhances nitrogen metabolism and disease resistance.

Iron: Assists in chlorophyll production, respiration, and energy transfer.

Manganese: Essential for chlorophyll development, metabolizing herbicides, and in plant respiration.

Zinc: Promotes root development and is essential for shoot growth and seed formation.

Warning: The application of Boron on any crops other than those recommended may result in serious injury to the crop. Contact your county agent or field representative before making application.

Micronutrient Solution for Maximum Crop Production

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

GUARANTEED ANALYSISBoron (B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0%Copper (Cu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% 0.5% Chelated Copper (Cu)Iron (Fe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.25% 0.25% Chelated Iron (Fe)Manganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0% 2.0% Chelated Manganese (Mn)Zinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0% 2.0% Chelated Zinc (Zn)

Derived from copper EDTA, iron EDTA, manganese EDTA, zinc EDTA, and boric acid.

GUARANTEED ANALYSISBoron (B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0%Copper (Cu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% 0.5% Chelated Copper (Cu)Iron (Fe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.25% 0.25% Chelated Iron (Fe)Manganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0% 2.0% Chelated Manganese (Mn)Zinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0% 2.0% Chelated Zinc (Zn)

Derived from copper EDTA, iron EDTA, manganese EDTA, zinc EDTA, and boric acid

KEEP OUT OF REACH OF CHILDRENWARNING

Combustible liquid. Harmful if swallowed. Harmful in contact with skin. Causes skin irritation. Causes eye irritation. Harmful if inhaled. May cause respiratory irritation. May cause drowsiness or dizziness. Suspected of damaging fertility or the unborn child.

PRECAUTIONARY STATEMENTS:Read all safety and precautionary statements before handling. Keep away from heat, sparks, open flames, hot surfaces and all other ignition sources. Do not smoke where product is stored or in use. Avoid inhaling fume/mist/vapours/spray. Do not eat or drink when using this product. Wear protective gloves and clothing and use eye and face protection. Always wash skin thoroughly after handling. Use only outdoors or in a well-ventilated area.

IF SWALLOWED: Call a poison control center or doctor/physician if you feel unwell. Rinse mouth. IF ON SKIN: Wash with plenty of soap and water. Call a poison center or doctor/physician if you feel unwell. If skin irritation persists: Get medical advice/attention. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a poison control center or doctor/physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do - continue rinsing. If eye irritation persists: Get medical advice/attention.

Remove and wash contaminated clothing before wearing again. In case of fire: Use water, dry powder, carbon dioxide or foam to extinguish. Store product in secure, locked, well-ventilated facility. Keep container tightly closed. Dispose of unused contents and container to an approved waste disposal plant in accordance with local/regional/national regulations.

GENERAL INFORMATIONBALANCE is formulated to be used in fertilizer solutions and is recommended as a supplement to a well-balanced fertilizer program. Highest efficiency is expected from band application, although broadcast, band or row applications are acceptable. Micronutrient deficiencies usually occur when plants are small and are most effective when added to fertilizer before or at planting.

APPLICATION INSTRUCTIONSFoliar Spray ApplicationsFor foliar spraying with a conventional sprayer, use a minimum of 20 gallons of water per acre per quart of BALANCE. A maximum of 1 quart per acre is recommended if foliar spraying BALANCE with low-volume equipment. Burning may occur in low-volume spray applications with little water. Spray when the crop is in an active growing stage after irrigation or rainfall for best results. Early mornings or late afternoon spray application is recommended.Vegetables: Incorporate BALANCE into the normal spray program, applying 1/2 to 1 quart per acre each spray.Field Crops: Apply 1 quart per acre when plants are young. This is the time when the most severe deficiencies occur.Tree and Vine Crops: Split applications are most beneficial and recommended. Apply 1 quart per 125 gallons of spray mixture. If using concentrated spray, increase the concentration in direct proportion to the dilution. It’s possible to split the above amount into several applications.

Aerial ApplicationsConsult an agronomist for application rates and dilutions.

Soil ApplicationsBALANCE is recommended for use on all types of soils using sprinkler, drip, or band application. Dilute prior to use for uniform coverage. BALANCE can be incorporated into liquid fertilizers or applied separately. Apply using the following rates if you do not have a leaf or soil analysis:Maintenance Application - 1 quart per acre.Moderate Deficiency - 2 to 3 quarts per acre.Severe Deficiency - 4 quarts per acre.

MIXING INSTRUCTIONSTank Mixes: Many pesticides can be applied with balance. Compatibility testing is required before mixing with pesticides or other chemicals. An adequate test for compatibility involves mixing the proper proportions of the product with water and the other ingredients in a small container. Agitate and let stand for one hour. If a precipitate forms, apply the products separately. BALANCE will disperse in water with little or no agitation. Many pesticides can be applied with BALANCE. Follow the mixing sequence of water, BALANCE, then pesticide.

Tank Buffering: Water with a pH greater then 6 may diminish pesticide efficacy by way of alkaline hydrolysis. A pH buffer, may be used to lower and maintain the pH of a spray tank and improve application efficacy.

STORAGE INSTRUCTIONSBALANCE is a chelate with low corrosivity. It is recommended that BALANCE be stored in fiberglass, polyethylene, or polyolefin. Do not stack pallets.

Information regarding the contents and levels of metals in this product is availableon the internet at http://www.aapfco.org/metals.htm

CONDITIONS OF SALE AND LIMITATIONS OF WARRANTY AND LIABILITYThe manufacturer or seller makes no other expressed or implied warranty of fitness or merchantability of any other expressed or implied warranty. In no case shall the seller be liable for consequential, special, or indirect damage resulting from the use or handling of this product. The manufacturer and the Seller offer this product, and the Buyer and User accept it, subject to the foregoing Conditions of Sale and Warranty, which may be varied only by agreement in writing signed by a duly authorized representative of the manufacturer.

Balance

Weight per Gallon: 10.7 lb. (4.8 kg) @ 68 ˚FNET CONTENTS: 2.5 GALLONS

Chelated Micronutrients Solution

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

T E C H N O L O G YMICRO FUSION

BW-MicroFurrow CornEDTA Chelated Corn Mix

BW MicroFurrow Corn Mix is an EDTA chelated formulation that increases nutrient uptake and efficiency. Designed to prevent and correct deficiencies of copper, manganese and zinc. It can be applied alone or with compatible chemicals or liquid fertilizers, including those containing 100% orthophosphate and suspensions.

BW MicroFurrow Corn Mix is a chloride-free, water-soluble and non-corrosive solution with a near neutral pH.

BENEFITS OF BW MICROFURROW CORN MIX

and herbicides

APPLICATION INSTRUCTIONSSoil ApplicationApply in-furrow, 2x2, or at sidedress or topdress. Do not apply directly on the seed in saline, alkali, or coarse textured soils.

Foliar Application

products

program

high-temperature periods

absorption

RECOMMENDED RATESRecommend use is based on the results of a soil and/or tissue analysis. If no analysis is performed, apply according to the suggested application rates for one growing season.

PLANT NUTRIENT FUNCTIONSThe primary benefits of the nutrients in MicroFurrow Corn Mix include:

Copper: Activates enzymes to convert amino acids to proteins, enhances nitrogen metabolism and disease resistance.


Zinc: growth and seed formation.

Sulfur: Aids in synthesis of protein and enzymes.

Nitrogen: Vital component of chlorophyll for photosynthesis and amino acids for building essential proteins.

Advanced EDTAChelated Corn Mix

GUARANTEED ANALYSIS

. . . . . . . . . . . . . . . . .

Derived from: copper di-ammonium EDTA, manganese di-potassium EDTA, zinc di-ammonium EDTA

Application Timing

Before planting

1-2 quarts At planting

1-2 pints V5-V6

GENERAL INFORMATIONMicroFurrow Corn Mix should be used to prevent and/or correct copper, manganese and zinc deficiencies. Apply this product alone or in combination with compatible agriculture chemicals or liquid fertilizers, including those containing 100% orthophosphate and suspensions.

DIRECTIONS FOR USESoil ApplicationApply in-furrow, 2x2, or at sidedress or topdress. Do not apply directly on the seed in saline, alkali, or coarse textured soils.Foliar ApplicationFill spray tank with water before adding fertilizer or other products.Use only as a supplement to a regular nutrient management program. Repeat applications may be beneficial. To avoid foliar burn, use as directed. Do not apply during periods of high temperatures or if crop is excessively stressed for moisture. Apply with a surfactant to enhance leaf coverage and increase nutrient absorption.

RECOMMENDED RATESThis product should be used on the basis of a soil and/or tissue analysis. In the absence of soil and/or tissue analysis, use the suggested application rates for one growing season (gallons per acre).


WARRANTY—CONDITIONS OF SALEOUR DIRECTIONS FOR USE of this product are based upon tests believed reliable. Follow directions carefully. Timing and method of application, weather and crop conditions, mixtures with other chemicals not specifically recommended and other influencing factors in the use of this product are beyond the control of the Seller. To the extent consistent with applicable law, Buyer assumes all risks of use, storage and handling of this material not in strict accordance with directions given herewith.To the extent consistent with applicable law, in no case shall the Manufacturer or the Seller be liable for consequential, special or indirect damages resulting from the use or handling of this product when such use and / or handling is not in strict accordance with directions given herewith. The foregoing is a condition of sale by the Seller and is accepted as such by the Buyer.

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

BW-MicroFurrow CornEDTA Chelated Corn Mix

GUARANTEED ANALYSISCopper (Cu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% 0.5% Chelated CopperManganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% 0.5% Chelated ManganeseZinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5% 4.5% Chelated ZincSulfur (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0%Nitrogen (N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0%

NET CONTENTS: 2.5 GALLONS

Derived from: copper di-ammonium EDTA, manganese di-potassium EDTA, zinc di-ammonium EDTA

May be harmful if swallowed. May cause skin irritation. May cause eye irritation. May cause respiratory irritation.

This fertilizer contains copper, manganese, and zinc and should be used only as recommended. It may prove harmful when misused.

PRECAUTIONARY STATEMENTSCall a poison center/physician if unwell. If skin irritation occurs, seek medical advice. If in eyes, rinse cautiously with water for several minutes; remove contact lenses. If eye irritation persists, seek medical advice. Wash hands after handling. Use only outdoors or in well ventilated areas. Avoid breathing mist/spray. If inhaled, remove to fresh air and keep at rest in a position comfortable for breathing. Store container tightly closed. Dispose of contents/container in accordance with national/regional/local regulations.

FIRST AIDIf inhaled: Move victim to fresh air. Seek medical attention if irritation persists.If on skin: Wash affected areas with soap and water. Seek medical attention if irritation persists. Wash contaminated clothing before re-use.If in the eyes: Immediately flush with water for at least 20 minutes. Seek medical attention if irritation persists.If swallowed: If victim is alert and not convulsing, give one glass of water to dilute material and induce vomiting. Seek immediate medical attention.

Application Use Rate(per acre) Timing

Soil (broadcast) 2-3 gallonsBefore planting

Soil (2x2) 2-8 quarts

Soil (in furrow) 1-2 quarts At planting

Foliar 1-2 pints V5-V6

STORAGEStore in fiberglass, stainless steel, or poly tanks. Do not store in carbon steel tanks. All forms of copper react with carbon steel. This reaction could cause red or black copper to drop out, decreasing the copper analysis.

MicroFurrow SoybeanEDTA Chelated Soybean Mix

BW MicroFurrow Soybean Mix is an EDTA chelated formulation that increases nutrient uptake and efficiency. Applied alone, it efficiently prevents and/or corrects iron, manganese, and zinc deficiencies. It can also be applied in combination with compatible agricultural chemicals and liquid fertilizers, including those containing 100% orthophosphate and suspensions.

BW MicroFurrow Soybean Mix is a chloride-free, water-soluble, and non-corrosive solution with a near neutral pH.

BENEFITS OF BW MICROFURROW SOYBEAN MIX• Compatible for application with most liquid fertilizers, insecticides, and herbicides• Prevents and corrects micronutrient deficiencies• Improved plant quality and yield potential

APPLICATION INSTRUCTIONSSoil ApplicationApply in-furrow, 2x2, or at sidedress or topdress. Do not apply directly on the seed in saline, alkali, or coarse textured soils.Foliar Application• Fill spray tank with water before adding fertilizer or other chemical products• Intended only as a supplement to a regular nutrient management program• Use recommended application rates to avoid foliar burn• Do not apply if plants are stressed for moisture or during high-temperature periods• Use with a surfactant can increase leaf coverage and nutrient absorption• Crop can benefit from repeat application

RECOMMENDED RATESUsage should be based on a soil and/or tissue analysis. If no analysis is performed, apply according to the suggested application rates for one growing season.

PLANT NUTRIENT FUNCTIONSThe primary benefits of the nutrients in the MicroFurrow Soy Mix include:

Iron: Assists in chlorophyll production, respiration and energy transfer



Advanced EDTAChelated SoybeanMix

55560 150th Ave | Fonda, IA 50540 | 712-288-6210






GUARANTEED ANALYSISIron (Fe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% 0.5% Chelated IronManganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5% 4.5% Chelated ManganeseZinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.75% 0.75% Chelated Zinc

Derived from: zinc EDTA, manganese EDTA, iron EDTA

GENERAL INFORMATIONApply this product alone for the prevention and/or correction of iron, manganese and zinc deficiencies. It can be applied alone or in combination with compatible agriculture chemicals or liquid fertilizers, including those containing 100% orthophosphate and suspensions.

DIRECTIONS FOR USESoil ApplicationApply in-furrow, 2x2, or at sidedress or topdress. Do not apply directly on the seed in saline, alkali, or coarse textured soils.Foliar ApplicationFill spray tank with water before adding fertilizer or other products.Use only as a supplement to a regular nutrient management program. Repeat applications may be beneficial. To avoid foliar burn, use as directed. Do not apply during periods of high temperatures or if crop is excessively stressed for moisture. Apply with a surfactant to enhance leaf coverage and increase nutrient absorption.

RECOMMENDED RATESThis product should be used on the basis of a soil and/or tissue analysis. In the absence of soil and/or tissue analysis, use the suggested application rates for one growing season (gallons per acre).



55560 150th Ave | Fonda, IA 50540 | 712-288-6210

MicroFurrow SoybeanEDTA Chelated Soybean Mix

GUARANTEED ANALYSISIron (Fe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% 0.5% Chelated IronManganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5% 4.5% Chelated ManganeseZinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.75% 0.75% Chelated Zinc


Derived from: zinc EDTA, manganese EDTA, iron EDTA

Causes skin irritation. Causes serious eye irritation.

PRECAUTIONARY STATEMENTSWear protectivce gloves and clothing. Remove and wash contaminated clothing before wearing. Avoid breathing vapors/mists. Use outdoors or in well-ventilated area. Call poison control or seek medical attention if you feel unwell. Wash thoroughly after handling. Do not eat, drink or smoke when using this product.

FIRST AIDIf inhaled: Move to fresh air and keep comfortable, call POISON CENTER or doctor if unwell.If on skin: Wash affected areas with soap and water. Seek medical attention if irritation persists. Wash contaminated clothing before reuse.If in the eyes: Immediately flush with water for 15-20 minutes, remove contact lenses if present and easy to do - continue rinsing. Seek medical attention if irritation persists.If swallowed: Rinse mouth. DO NOT INDUCE VOMITING unless directed by medical professional. Seek medical attention if unwell.






BW-MicroFoliar IIIMicronutrient Solution

GUARANTEED ANALYSIS: 4-0-0 Total Nitrogen (N) 4%

Sulfur (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% 3.0% Combined Sulfur (S)Boron (B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3%

0.3 % Water Soluble Boron (B)Manganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% 3.0% Water Soluble Manganese (Mn)Molybdenum (Mo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.01%

0.01% Water Soluble Molybdenum (Mo)Zinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% 3.0% Water Soluble Zinc (Zn)

DERIVED FROM: Zinc Sulfate, Manganese Sulfate, Sodium Borate and Sodium Molybdate

BW Fusion MicroFoliar III is an advanced foliar micronutrient solution developed for in-season nutrient applications on row crops. It’s a ready-to-use formulation that’s an ideal tank mix partner for glyphosate and late-season fungicide applications.

ADVANTAGES OF FOLIAR FEEDINGFoliar feeding is an extremely efficient and effective method of providing essential nutrition to row crops during critical growth stages. Applying solutions directly on plant leaves allows immediate nutrient absorption for high plant uptake, resulting in improved plant health and yield potential.

BENEFITS OF BW FUSION MICROFOLIAR III

application rate per acre

insecticides

APPLICATION INSTRUCTIONSFoliar Application

per application as a maintenance program.Aerial ApplicationApply 1-2 pints Micro Foliar III per acre with 5 gallons of water. Multiple applications are recommended for best results.Soil Application

per application as a maintenance program. Micro Foliar III is not for use with starter fertilizer.

PLANT NUTRIENT FUNCTIONSThe primary benefits of the nutrients in MicroFoliar III include:


Boron: Vital to new growth and essential for pollination and seed production. Also enhances nitrogen uptake and utilization.


Molybdenum: Transforms nitrogen into amino acids for building plant proteins.


Advanced FoliarNutrition Solution

55560 150th Ave | Fonda, IA 50540 | 712-288-6210


55560 150th Ave | Fonda, IA 50540 | 712-288-6210

MicroFoliar IIIMicronutrient Solution

NET CONTENTS: 2.5 GALLONSNet Weight: 10.5lb / gallon

APPLICATION INFORMATIONFoliar ApplicationApply 1-2 quarts Micro Foliar III per 10-20 gallons of water per acre per application as a maintenance program.Aerial ApplicationApply 1-2 pints Micro Foliar III per acre with 5 gallons of water. Multiple applications are recommended for best results.Soil ApplicationUse 1 - 3 quarts Micro Foliar III per 10-20 gallons of water per acre per application as a maintenance program. Micro Foliar III is not for use with starter fertilizer.

Warning: Some crops may be injured by the application of Boron.

Information regarding the contents and levels of metals in this product is available on the internet at http://www.aapfco.org/metals.htm

MIXING INSTRUCTIONSPut 1/3 to 2/3 of total desired water volume in tank. Add adjuvant(s) if desired and agitate until thoroughly mixed. Add pesticide(s) if desired and agitate until thoroughly mixed. Add desired amount of MicroFoliar III and agitate until thoroughly mixed. Fill tank with remainder of desired water. A jar test is a good field practice for evaluating compatibility of multiple chemical mixtures. Check compatibility with chemical mixtures and high phosphate and alkaline (high pH) solutions.

HAZARD STATEMENTSMay be harmful if swallowed. Causes mild skin irritation. Causes eye irritation.

This material should only be used as recommended. It may prove harmful when misused.

• Avoid contact with eyes• Avoid contact with skin• Do not breath mist or vapor• Do not swallow• Wash thoroughly after handling


Causes eye irritation. Suspected of damaging fertility or the unborn child. May cause damage to organs through prolonged or repeated exposure. Harmful to aquatic life with long lasting effects.

Warning: This plant nutrient contains Boron and Molybdenum, which may be injurious to certain crops. Contact your local county agent or field consultant for specific information.

GENERAL INFORMATIONMicroFoliar III is formulated for quick and efficient foliar nutrient delivery to row crops, vegetables, fruit & nut trees and fruiting vine crops to prevent and correct micronutrient deficiencies. The specific mixture and formulation of nutrients in MicroFoliar III allow season long versatility and can be applied at any growth stage for correction of micronutrient deficiencies.

FIRST AIDIf In Eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists, seek medical advice or attention.

PERSONAL PROTECTIVE EQUIPMENTWear gloves and protective clothing. Wear eye protection (glasses, goggles or face shield).

STORAGE & DISPOSALStore product in original container. Do not store in excessive cold or heat. Do not reuse container. Do not contaminate water, food or feed by storage or disposal. Keep packaging closed, securely fastened and upright. Triple rinse or equivalent and dispose of container in accordance with local, state and federal regulations.

BW-MicroFoliar is a specially formulated Foliar Applied micronutrient product designed to bring manganese, zinc, sulfur, and boron to all crops.

Guaranteed Analysis: 4-0-0Total Nitrogen (N) ............................. 4% (4% Urea Nitrogen)

Sulfur (S)....................................... 3% (3% Combined Sulfur)

Boron (B) .......................... 0.3% (0.3% Water Soluble Boron)

Manganese (Mn) ..........3% (3% Water Soluble Manganese)Zinc (Z) ...................................... 3% (3% Water Soluble Zinc)

Molybdenum (Mo)......................0.01% (Water Soluble Molybdenum)

BW-MicroFoliar IVMicronutrient Solution

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

GUARANTEED ANALYSISSulfur (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5% 1.5% Combined sulfurBoron (B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0% 2.0% Water soluble boronManganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% 3.0% Water soluble manganeseMolybdenum (Mo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1% 0.1% Water soluble molybdenumZinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% 3.0% Water soluble zinc

Derived from sodium borate, manganese sulfate, sodium molybdate and zinc sulfate.

BW Fusion MicroFoliar IV is an advanced foliar micronutrient solution developed for in-season nutrient applications on row crops. It’s a ready-to-use formulation that’s an ideal tank mix partner for glyphosate and late-season fungicide applications.

ADVANTAGES OF FOLIAR FEEDINGFoliar feeding is an extremely efficient and effective method of providing essential nutrition to row crops during critical growth stages. Applying solutions directly on plant leaves allows immediate nutrient absorption for high plant uptake, resulting in improved plant health and yield potential.

BENEFITS OF BW FUSION MICROFOLIAR IV

application rate per acre

insecticides

APPLICATION INSTRUCTIONSFoliar Application

acre per application as a maintenance program.Aerial Application

Multiple applications are recommended for best results.Soil Application

for use with starter fertilizer.

PLANT NUTRIENT FUNCTIONSThe primary benefits of the nutrients in MicroFoliar IV include:


Boron:seed production. Also enhances nitrogen uptake and utilization.

Manganese:metabolizing herbicides, and in plant respiration.

Molybdenum: Transforms nitrogen into amino acids for building plant proteins.


Advanced FoliarNutrition Solution

Causes eye irritation. Suspected of damaging fertility or the unborn child. May cause damage to organs through prolonged or repeated exposure.

GENERAL INFORMATIONBW-MICROFLIAR IV is uniquely formulated for foliar delivery of manganese, zinc, boron and molybdenum for all crops.

RATE RECOMMENDATIONSFoliar ApplicationGround: Apply 1-4 pints in a minimum of 10 gallons of water per acre and repeat as needed.Aerial: Apply 1-3 pints in a minimum of 2 gallons of water per acre and repeat as needed.

Soil ApplicationUse 1-3 quarts in a minimum of 10 gallons of water per acre. Not for use with starter fertilizer.

Optimum application rate will vary depending on the interval of treatment, soil properties (pH, organic matter content, texture), weather conditions, time of year, plant species and its nutrient requirements. For optimum results, follow soil/tissue test recommendation.

MIXING AND HANDLING INSTRUCTIONSFill mix tank with half of required water volume and agitate. Add products in this order, mixing thoroughly after each addition: adjuvants, pesticides, then fertilizers. Fill tank with remainder of water and continue agitation until solution is mixed completely. Use a jar text to check chemical mixture compatibility prior to application. Not compatible with phosphate (P2O5) solutions.


ATTENTION: MICROFOLIAR IV contains boron; use on any crops other than those recommended may result in serious injury to the crops. The application of fertilizing materials containing molybdenum (Mo) may result in forage crops containing levels of molybdenum (Mo) which are toxic to ruminant animals.

Information regarding the contents and levels of metals in this product is available on the Internet at http://www.aapfco.org/metals.html.

PRECAUTIONARY STATEMENTSSpecial instructions should be obtained before use. Do not handle until all safety precautions have been read. Wear protective gloves/clothing and eye/face protection. Do not breathe mist or vapor. Wash thoroughly after handling. Avoid release to the environment.

FIRST AIDIf in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists, get medical attention. If exposed or concerned, get medical attention.

STORAGE AND DISPOSALDo not contaminate water, food or feed by storage or disposal. Keep out of reach of children. Store locked up. Dispose of contents/container in accordance with local regulations.

WARNING: Cancer and Reproductive Harm-www.P65Warnings.ca.gov


55560 150th Ave | Fonda, IA 50540 | 712-288-6210

BW-MicroFoliar IV

Micronutrient Solution

GUARANTEED ANALYSISSulfur (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5% 1.5% Combined sulfurBoron (B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0% 2.0% Water soluble boronManganese (Mn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% 3.0% Water soluble manganeseMolybdenum (Mo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1% 0.1% Water soluble molybdenumZinc (Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% 3.0% Water soluble zinc


Derived from sodium borate, manganese sulfate, sodium molybdate and zinc sulfate.

B D - S w e e t : C o l d P r o c e s s e d C a n e S u g a r w i t hC a l c i u m a n d O r g a n i c A c i d P r o f i l e

BD-Sweet utilizes unpasteurized sugar paired with calcium to help build cell walls, help stimulate root and leaf development, and help uptake and activity of other nutrients. BD-Sweet supplements/feeds the microbial populations and is designed to help the plant process applied pesticides along with supplying critical nutrition to the plant.

BD-Sweet can be used in-furrow at planting with other crop protection products, fertilizers, and biostimulants. BD-Sweet can also be applied with foliar fungicides at the VT (vegetative tassel) growth stage in corn and R1 and R3 repro-ductive growth stages in soybeans. BD-Sweet can be applied multiple times during the season for an energy / nutrient source to crops has been shown to improve yield in both corn and soybeans.

55560 150th Ave / Fonda, IA 50540 / 712-288-6210

www.bw-fusion.com

BD-Sweet

BD-Sweet is dosed at 1-2 pints per acre in-furrow or

foli-ar for corn an soybean crops. Can be used with crop

protection products, fertilizers, and biostimulants

BD - S w e e t T r a i t s

1) Sugar - Cane sugar is a humectant (preventsplant moisture loss) and helps foliar appliedfungicides stick to leaves, especially duringreproductive stages. The sugar componentalso helps feed the applied or native soilbeneficial microbial populations.

2) Calcium- Helps the plant heal fromenvironmental injuries (i.e. foliar tissuedamage from hail, insect, and/or varmintdamage). Calcium also plays a role inmicrobial cell development and theproliferation process.

GUARANTEED ANALYSISCalcium..........................................................0.3%

Derived from : calcium hydroxide, cane sugar, and organic acids

HAZARD STATEMENTS: May cause damage to organs through prolonged or repeated exposure. May cause cancer. May be harmful if swallowed.

PRECAUTIONARY STATEMENTS: Do not handle until all safety precautions have been read and understood. Do not breathe dust/fumes/gas/mist/vapors/spray.

Wear protective gloves/clothing/eye and face protection. Avoid release into the environment. Store locked up. Dispose of contents/containers in accordance with local/state/Federal laws and regulations. If exposed, concerned, or feel unwell, get medical advice/attention.

HANDLING AND STORAGE:

BW-Sweet is a mildly corrosive liquid fertilizer and should be handled and used in accordance with state, local, and federal regulations where applicable. Materials and methods of construction selected for storage and handling should be those recommended by qualified manufacturers, associations, or recognized testing labs. Type 304 or 316 stainless steel, polyolefins, fiberglass, reinforced plastic, polyvinyl chloride, polypropylene, polyethylene-applied coatings and rubber linings are generally suitable for storage and handling of mixed liquids, Aluminum, brass, copper, zinc, and many alloys, especially those of copper base, are unsuitable for use in storing and handling mixed liquid fertilizers and must be avoided. Rinse and flush thoroughly before retiring equipment for the season.

CONDITIONS OF SALE:

Seller warrants that their product consists of the ingredients specified and is reasonably fit for the purpose stated when used in accordance with directions under normal conditions for use. EXCEPT AS PROVIDED ABOVE, THERE ARE NOT OTHER WARRANTIES, EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABLE AND FITNESS FOR A PARTICULAR PURPOSE.

Because the time, place, rate of application and other conditions of use are beyond the seller's control, seller's liability from handling, storage and use of the product is limited to the replacement of product or refund of purchase price. SELLER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES.

BD-Sweet

Recommendations for Use: Apply 1-2 pints per acre in-furrow or foliar per acre for corn and soybean

crops. Can be used with crop protection products, fertilizers, and

other biostimulants.

BD-Sweet

Weight per Gallon: 9.8lbs @ 60 degrees F Acidity: PH 8.2

Color: Clear to AmberPackages Size: Bulk, Minibulk

Net Contents: 275 Gallons

Keep out of reach of childrenRead label before use and if medical advice is needed have

product container or label at hand

Cold Processed Cane Sugar +

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

BW-NLockdownNitrogen Stabilizer

BW NLockdown protects growers’ fertilizer investment with superior nitrogen stabilization. Use of this product helps soil retain more nitrogen to increase fertilizer efficiency, even in wet and challenging field conditions.

A NITROGEN STABILIZER IS CRITICAL WHEN:• Fertilizer is surface applied, especially to moist soils• There’s high crop residue such as reduced or no-till conditions• Nitrogen loss increases at or near the soil surface due to warm

temperatures, high soil pH, and other challenging field or weatherconditions

ADVANTAGESAs much as 40% of nitrogen can be lost with normal fertilizer applications. BW NLockdown prevents this loss during the critical days immediately after fertilizer application. The unique formulation and production process coats and protects more nitrogen than competitive products by piercing the prill deeper. This makes the product more effective in warm weather, with moisture variations, and wet conditions.

TWO-WAY PROTECTIONBW NLockdown reduces nitrogen loss in two ways:1. Inhibits activity of the urease enzyme that breaks down urea2. Slows the conversion of urea to ammonia gas

BENEFITS OF BW NLOCKDOWN• Retards hydrolysis of urea and controls volatility• Prevents ammonia loss while the urea is on the soil surface• Keeps nitrogen available to plant longer, maximizing nitrogen

investment• Reduced ammonia emissions• Superior coverage and flow due to surfactant• Fast-drying solution for easier handling• Requires less blending time to speed operations• Penetrating agent treats more of the urea granule for moreconsistent results

Effective NitrogenLoss Protection

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

ACTIVE INGREDIENT

NBPT (N-(n-butyl)-thiophosphoric triamide) . . . . . . . . . 26.7%OTHER INGREDIENTS . . . . . . . . . . . . . . . . . . . . . . . . . . 73.3%TOTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100.0%

APPLICATION INSTRUCTIONSBW Lockdown is urea specific and formulated for any nitrogen consuming plants such as row crops, sod, pastures, ornamentals, specialty crops, turfgrass, landscape and nursery plantings. It’s recommended for surface application of urea and urea-containing fertilizers such as pre-plant, pre-emergence, side-dress, top-dress, broadcast or other post-planting applications.

Factors that increase volatilization should be considered when choosing the appropriate rate include:1. High soil moisture2. Drying conditions such as low humidity, sun and wind3. High air and soil temperatures4. High pH soils5. Low organic matter and lower Cation Exchange Capacity

(CEC) soils6. High amounts of crop residue7. Length of control needed

Urea UAN2.0 to 3.0 Qts. / Ton 1.0 to 1.5 Qts. / Ton

RECOMMENDED RATES26.7% by weight active ingredient solution.

When conditions favoring volatility exist, or when longer controlis needed, the rate may be increased by 1 quart / ton.

Causes skin irritation. Causes serious eye damage. May cause respiratory irritation. Possible risk of impaired fertility. See FIRST AID and Additional Precautionary Statements Below Read Entire Label Before Using This Product.

DIRECTIONS FOR USEWARNING: Read the entire label before use. Use only according to label directions. Before buying or using this product, read the “Warranty Sales of Conditions.” If terms are unacceptable, return at once unopened to place of purchase. Always wear proper personal protection (recommend long sleeves and long pants, goggles and ANSELL EDMONT NEOX Neoprene gloves Number 9-912 or equivalent when handling the product.) Use only with adequate ventilation (large volumes of air movement). If organic vapors or dusts are present above their regulatory limits, follow a respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 or applicable Federal / State, provincial or local requirements whenever workplace conditions warrant respirator use.

APPLICATION RATESThis product is urea specific and may be used for any nitrogen consuming plants including Ornamentals, Pastures, Row crops, Sod farms, Specialty crops, Turfgrass and other landscape and nursery plantings. This product is recommended for surface application of urea and urea containing fertilizers such as pre-plant, pre-emergence, side-dress, top-dress, broadcast or other post-planting applications. The benefits of this product as a urease inhibitor are a result of its ability to retard the hydrolysis of urea and control volatility, preventing ammonia loss while the urea is on the soil surface. Many factors in the environment contribute to volatilization. The factors increasing volatilization that should be considered when choosing the appropriate rate include:1. High soil moisture2. Drying conditions including low humidity, sun and wind3. High air and soil temperatures4. High pH soils5. Low organic matter and lower Cation Exchange Capacity (CEC) soils6. High amounts of crop residue7. Length of control needed

KEEP OUT OF REACH OF CHILDRENDANGER

FOR BLENDING ON UREAEquipment Required

particles with this product. A rotary device that can tumble the urea and allow for uniform contact with this product without spillage is appropriate. Auger and paddle mixers may also be used. Exposed inner surfaces should be clean, dry and rust free.

Procedure1. Wear proper personal protection which is long sleeves and long pants, goggles and ANSELL EDMONT NEOX Neoprene gloves Number 9-912 or equivalent.2. Use only with adequate ventilation with large volumes of air movement. If used with inadequate ventilation respiratory protection is required.3. Weigh the urea and transfer into the mixing or blending equipment.4. Measure the desired quantity of this product.5. Apply the product to the urea in the blender. Blend well before introducing other fertilizer materials and allowing adequate time for uniform coverage. A dye isincluded in the product to assist in evaluating the uniformity of coverage.6. Under certain temperature and humidity conditions urea blended with theproduct may stick together. Often the addition of other fertilizer materials to theblender, such as potash, will eliminate the need to add a drying agent. If theparticles remain sticky, add small amounts of finely ground, highly absorbent,free-flowing powders such as attapulgite clays at concentrations as low as 0.25% by weight of the treated urea.

Storage after blendingGranular dry urea treated with this product is suitable for long-term storage in sealed plastic bags. Research shows stabilized fertilizer packaged in sealed plastic bags may be stored 9 months between 66° and 77°F.

FOR MIXING WITH UREA AMMONIUM NITRATE (UAN) SOLUTIONSProcedure1. Wear proper personal protection which is long sleeves and long pants, goggles and ANSELL EDMONT NEOX Neoprene gloves Number 9-912 or equivalent.2. Use only with adequate ventilation with large volumes of air movement. If used with inadequate ventilation respiratory protection is required.3. Fill the spray tank half full with UAN solution.4. Add the product to the UAN solution and mix thoroughly by agitation prior toadding pesticides or surfactants.5. With agitators on, add the appropriate amount of this product for the desiredconcentration in the full volume.6. Mix well and then add the remainder of the UAN solution.7. Use blended UAN solution soon after mixing. If necessary, UAN treated with this product may be stored up to 10 weeks.

Urea UAN2.0 to 3.0 Qts. / Ton 1.0 to 1.5 Qts. / Ton

USE RATE CHART26.7% by weight active ingredient solution.

When conditions favoring volatility exist, or when longer control is needed, the ratemay be increased by 1 quart / ton.

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

BW-NLockdownNitrogen Stabilizer

ACTIVE INGREDIENT

NBPT (N-(n-butyl)-thiophosphoric triamide) . . . . . . . . . . . . . . . . . . . . . . . . 26.7%OTHER INGREDIENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.3%TOTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100.0%


SHAKE WELL BEFORE USE

Boron deficiency

BW-Boron 7%BW-Boron 7% is important for strong cell walls, disease resistance, stem branching, nodulations in legumes, flower development and pollination. Boron 7% is essential in providing sugars to plant roots and therefore in necessary in the soil. It is generally a soluble nutrient but is usually only available to the plant from a soil application when adequate supply and water is available to the plant. Boron 7% can provide consistent growth under adverse soil conditions. It is not easily transported within the plant. Boron 7% is needed for pollen tube development as well as seed and fruit development. Legume crops generally require higher amounts of Boron 7% for nodulations. A general leaf test range for Boron 7% needs to be between 20 -100 ppm. BW-Boron formulation also contains salicylic acid which has been shown boost the plant's immune system. BW-Boron includes small amounts of Molybenum which is involved in transforming nitrogen into amino acids for building plant proteins. BW-Boron 7% can be applied in a 2x2 soil application but is not recommended in an on-seed starter or for in-furrow use. Applications use rate should be increased when foliar applied and be based on crop needs with the use of a plant tissue test to confirm final foliar rate.

Use rates:

Soil application: 16-32 oz/acre (apply only in 2x2 or away from seed)

Foliar application: 16-32 oz/acre

Note:

(10-15 gallon of a water carrier is recommended for adequate coverage)

* Do not apply to foliage if air temperature is to exceed 85 degrees at time of application

55560 150th Ave / Fonda, IA 50540 / 712-288-6210

www.bw-fusion.com

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

BW-Boron 7%

GUARANTEED ANALYSIS

Boron . . . . . . . . . . . . . . . . . . ... . . . . . . 7.0%Molybdenum . . . . . . . . . . . . . . . . . . . . 0.0075%Derived from: boric acid, molybdic oxide, chitosan, salicylic acid, EDTA


If medical advice is needed have product container or label at hand.

HAZARD STATEMENTSCauses skin irritation. Causes eye irritation. Harmful if swallowed. Harmful if inhaled. May cause respiratory irritation. May damage fertility or the unborn child.

PRECAUTIONARY STATEMENTSDo not handle until all safety precautions have been read and understood. Avoid breathing dust/fumes/mist/vapors/spray. Use only outdoors or in a well-ventilated area. Do not eat, drink or smoke when using this product. Wash hands, face, and other affected areas thoroughly after handling. Wear protective gloves/clothing/eye and face protection. Avoid release into the environment. Store locked up. Dispose of contents/containers in accordance with local/state/Federal laws and regulations.

FIRST AIDIF ON SKIN wash with plenty of water. If skin irritation occurs get medical advice/attention. Take off contaminated clothing and wash before reuse. IF IN EYES rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do so. Continue rinsing. If eye irritation persists get medication advice/attention. IF SWALLOWED call POISON CENTER/doctor if you feel unwell. Rinse mouth.IF INHALED remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a poison control center or doctor/physician if you feel unwell.

CHEMICAL & PHYSICAL PROPERTIESAcidity: pH 7.9 Color: ClearWeight per gallon: 10.25 lbs @ 60ºF

I

PACKAGE SIZE

____ 2.5 Gallon ____ 275 Gallon

GENERAL INFORMATIONBW-Fusion Boron 7% is a liquid fertilizer designed with boron, molybdic oxide, and EDTA, to maintain rapid vegetative growth under adverse soil conditions or soils low in that nutrient. Boron is essential to strong cell walls, disease resistance, stem branching (in legumes), flower development, and pollination.

DIRECTIONS FOR USEUse in 2x2 application at planting or in foliar applications according to crop needs at key development stages. Boron is generally not recommended for in-furrow use; use only after careful consultation with a BW-Fusion representative or your own agronomist. Use 16-32 oz/ac in 2x2 or 16-32 oz/ac foliar in corn or soybean. Consult with your agronomist and use a tissue test to confirm final foliar rates. BW-Boron 7% may be tank-mixed with most herbicides, fungicides, or insecticides, although a jar test is recommended. When applying to foliage, total spray volume of 10-15 gal/ac is recommended for best coverage. Do not apply if air temperature exceeds 85° F or in noonday sun.

Handling and StorageBW-Boron 7% is a mildly corrosive liquid fertilizer and should be handled and used in accordance with state, local and federal regulations where applicable. Materials and methods of construction selected for storage and handling should be those recommended by qualified manufacturers, associations, or recognized testing laboratories. Type 304 or 316 stainless steel, polyolefins, fiberglass, reinforced plastics, polyvinyl chloride, polypropylene, polyethylene-applied coatings and rubber linings are generally suitable for storage and handling of mixed liquids. Aluminum, brass, copper, zinc and many alloys, especially those of copper base, are unsuitable for use in storing and handling mixed liquid fertilizers and must be avoided. Rinse and flush thoroughly before retiring equipment for the season.

WARRANTY—CONDITIONS OF SALESeller warrants that their product consists of the ingredients specified and is reasonably fit for the purpose stated when used in accordance with directions under normal conditions for use. EXPECT AS PROVIDED ABOVE, THERE ARE NOT OTHER WARRANTIES, EXPRESS OR IMPLIED INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.1.Because the time, place, rate of application and other conditions of use are beyond sellers’ control, sellers’ liability from handling, storage and use of this product is limited to replacement of product or refund of purchase price. SELLER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES.

WARNING: Some crops could be injured by the application of Boron. Please contact your local agronomy representative before application. This product should only be used on soils that respond to molybdenum. CROPS HIGH IN MOLYBDENUM ARE TOXIC TO GRAZING ANIMALS.

55560 150th Ave | Fonda, IA 50540 | 712-288-6210

BW-Zinc 9% EDTA Chelated Zinc

GUARANTEED ANALYSIS

Zinc . . . . . . . . . . . . . . . . . . ... . . . . . . 9.0%Derived from: Zinc EDTA

KEEP OUT OF REACH OF CHILDREN WARNING

PRECAUTIONARY STATEMENTSKeep BW-Zinc 9% container tightly closed and avoid contact with eyes, skin, and avoid breathing vapors or coming into contact with spray mist. Wear protective gloves. Do not eat, drink, or smoke while using this product. Wash hand thoroughly after handling or using this product. Keep Away from Open Flame. In case of fire: use dry chemical fire extinguisher to extinguish and call Chemtrec at 800-424-9300.

FIRST AIDIF ON SKIN wash with plenty of water. If skin irritation occurs get medical advice/attention. Take off contaminated clothing and wash before reuse. IF IN EYES rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do so. Continue rinsing. If eye irritation persists get medication advice/attention. IF SWALLOWED call POISON CENTER/doctor if you feel unwell. Rinse mouth.IF INHALED remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a poison control center or doctor/physician if you feel unwell. Please see SDS for additional information

CHEMICAL & PHYSICAL PROPERTIES Acidity: pH 76.5-7.5 Color: Clear to slight yellowWeight per gallon: 10.9lbs @ 60ºF Odor: Slight odor

I

PACKAGE SIZE

____ 2.5 Gallon ____ 275 Gallon

GENERAL INFORMATIONBW-Fusion Zinc 9% is recommended to correct zinc deficiencies as shown through soil and/or plant tissue analysis.

DIRECTIONS FOR USE Corn and SoybeansSoil Applications: use 1-2 pints of BW-Zinc 9% per acre. Product is compatible for use with most liquid suspension fertilizers.

Foliar Application: 1-2 pints per acre of BW-Zinc in minimum of 10 gallons of water

Mixing Instructions

1. Pour 1/3 water or fertilizer in tank

2. Add other chemicals (if applicable)

3. Add the balance of water or fertilizer

4. Add BW-Zinc 9%

Storage and DisposalBW-Zinc 9% should be stored in a cool, dry place. Store in original container and keep container tightly closed. Do not reuse empty container. Triple rinse container when empty and offer for recycling or for disposal in sanitary landfill, or by other means in accordance with local, state, and federal laws and regulations.

WARRANTY—CONDITIONS OF SALESeller warrants that their product consists of the ingredients specified and is reasonably fit for the purpose stated when used in accordance with directions under normal conditions for use. EXPECT AS PROVIDED ABOVE, THERE ARE NOT OTHER WARRANTIES, EXPRESS OR IMPLIED INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.1 .Because the time, place, rate of application and other conditions of use are beyond sellers’ control, sellers’ liability from handling, storage and use of this product is limited to replacement of product or refund of purchase price. SELLER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES. Buyer assumes all risks and liability associated with BW-Zinc 9% used in any other manner other than those specifically set forth in the label.

BW-Fusion 55560 150th AveFonda, IA 50540

Tel: +1 (712) 288-6210 BW-Humic 10%Spec. No.: A-655 Effective DateRevision Date: July 8, 2013

BW-Humic 10% Liquid

Product Description BW-Humic 10% is a proprietary potassium humate for use in agricultural applications to enhance nutrient uptake. CAS No. 68514-28-3 (Humic Acid – Potassium Salt).

Sales Specifications Minimum Maximum Test Method

pH (3% Solution) 8.0 10.0 QC-002

-- QC-128 or Contract Lab % Humic Acid Content 10.0 Only active customers are notified of specification changes.

Typical Analysis (As is Basis)*

Chemical Data Physical Data Parameter Unit Parameter Unit pH 9.0 Color Black

Total Nitrogen (N) 0.11% Density 9.0lbs. /gallon Soluble Potash (K2O) 5.0%

Total Sulfur (S) 2.3% Calcium (Ca) 0.43% Iron (Fe) 0.10% Carbon (C) 7.5%

Oxygen (O) 9.4%

Storage Stability:

May vary from a few months to several years dependent upon the specific product and storage conditions.

Compatibility:

BW-Humic 10% is soluble over a pH range of 2.0 to 12.0. It is compatible with most commercially available fertilizers and pesticides. It is also compatible with most anionic and non-ionic materials. A jar test is

recommended prior to mixing to confirm specific compatibility with actual materials to be used.

Packaging:

BW-Humic 10% is available in 275 Gallon Totes and Tank Trucks

Lead Time:

Four weeks lead time is typical.

Material Safety Data Sheets are available upon request.

Please contact your BW-Fusion Representative for additional product information.

The information given here is based on our best knowledge and we believe it to be true and accurate. However, BW-Fusion does not warrant or guarantee in any manner whatsoever, including the warranty of merchant-ability or fitness for the end user the accuracy of the information and procedures listed

herein and will not be responsible for any damage resulting from their use.

BW-Fusion 55560 150th AveFonda, IA 50540

Tel: +1 (712) 288-6210 BW-Humic 20%Spec. No.: A-655 Effective DateRevision Date: July 8, 2013

BW-Humic 20% Liquid

Product Description BW-Humic 20% is a proprietary potassium humate for use in agricultural applications to enhancenutrient uptake. CAS No. 68514-28-3 (Humic Acid – Potassium Salt).


pH (3% Solution) 8.0 10.0 QC-002

% Humic Acid Content 20.0 -- QC-128 or Contract Lab Only active customers are notified of specification changes.

Typical Analysis (As is Basis)*

Chemical Data Physical Data Parameter Unit Parameter Unit pH 9.0 Color Black

Total Nitrogen (N) 0.11% Density 9.6 lbs. /gallon Soluble Potash (K2O) 5.0%

Total Sulfur (S) 2.3% Calcium (Ca) 0.43% Iron (Fe) 0.10% Carbon (C) 7.5%

Oxygen (O) 9.4%

Storage Stability:

May vary from a few months to several years dependent upon the specific product and storage conditions.

Compatibility:

BW-Humic 20% is soluble over a pH range of 2.0 to 12.0. It is compatible with most commercially available

fertilizers and pesticides. It is also compatible with most anionic and non-ionic materials. A jar test is

recommended prior to mixing to confirm specific compatibility with actual materials to be used.

Packaging:

BW-Humic 20% is available in 275 Gallon Totes and Tank Trucks

Lead Time:

Four weeks lead time is typical.



The information given here is based on our best knowledge and we believe it to be true and accurate. However, BW-Fusion does not warrant or guarantee in any manner whatsoever, including the warranty of merchant-ability or fitness for the end user the accuracy of the information and procedures listed


BW-Fusion55560 150th AveFonda, IA 50540

Tel: +1 712-288-6210 BW-Fulvic 30%Spec. No.: A-704 Effective Date: 3/5/13 Revision Date:

BW-Fulvic 30%Product Description

BW-Fulvic 30% is a 30% liquid solution of plant derived fulvic acids.


pH (As Is) 2.0 3.0 QC-002 % Fulvic Acids 30.0 --- QC-064 % Insolubles -- 1.0 QC-007

Only active customers are notified of specification changes.

Typical Analysis*

Chemical Data Physical Data

Parameter Unit Parameter Value

pH 2.5 Color Dark Brown

Fulvic Acids (%) 30.0 LBS/Gallon 9.67

*The above analyses are not formal specifications and values may change.

Storage Stability:

May vary from a few months to several years dependent upon the specific product and storage information.

Compatibility:

BW-Fulvic 30% is compatible with most liquid fertilizers, micronutrients and pesticides. However, a jar test is

recommended before mixing for field application.

Packaging:

BW-Fulvic 30% is available in 275 gallon totes or tank trucks

Lead Time:

Two weeks lead time is typical.



The information given here is based on our best knowledge and we believe it to be true and accurate. However, BW-Fusion does not warrant or guarantee

in any manner whatsoever, including the warranty of merchant-ability or fitness for the end user the accuracy of the information and procedures listed


ELEVATE YOUR K® with NACHURS® Bio-K®

®POWERED BY • A premium source of potassium fertilizer combined with a natural plant metabolite• Most effective and efficient source of potassium• Increased plant health and plant vigor resulting in maximum yield potential

MANUFACTURED FOR:BW FUSION

55560 150th Ave • Fonda, IA 50540712-288-6210

NUTRIENTS SUPPLIED (pounds per gallon):Soluble Potash (K20).......................... 2.55

Derived from: potassium acetate.

PRODUCT PROPERTIES:Analysis: 0-0-24Weight: 10.65 lbs. per gallonSpecific gravity: 1.28 kg/LpH: 9.5-10.5Appearance: clear, colorless to pale yellowOdor: slight sweet odor

GENERAL PRODUCT INFORMATION:BW-K ACE liquid fertilizer is a unique form of foliar potassium having superior foliar absorption over traditional forms of potassium. Unlike other liquid forms of potassium such as nitrates, hydroxides, thiosulfates or carbonates, BW-K ACE liquid fertilizer is not caustic or corrosive, resulting in safer foliar applications and less plant stress. BW-K ACE liquid fertilizer small molecular size coupled with the plant’s natural affinity for organic acids allows for a much higher degree of potassium absorption. For best results, apply BW-K ACE liquid fertilizer according to recommendations based on plant tissue or soil analysis.

FIRST AID: Please see SDS sheet for more information, call (800) 622-4877.

KEEP OUT OF REACH OF CHILDREN.

*THESE ARE GENERAL PRODUCT RECOMMENDATIONS. PLEASE CONSULT WITH YOUR AUTHORIZED NACHURS DISTRIBUTOR OR AGRONOMIST FOR SPECIFIC FERTILITY RECOMMENDATIONS. THESE RECOMMENDATIONS ARE BELIEVED TO BE RELIABLE AND SHOULD BE FOLLOWED CAREFULLY. FAILURE TO FOLLOW LABEL DIRECTIONS OR IMPROPER APPLICATION PRACTICES, ALL OF WHICH ARE OUT OF CONTROL OF THE MANUFACTURER OR SELLER, CAN RESULT IN PLANT OR LEAF DAMAGE. CROP INJURY MAY RESULT FROM UNUSUAL WEATHER CONDITIONS, FAILURE TO FOLLOW LABEL DIRECTIONS, OR IMPROPER APPLICATION PRACTICES ALL OF WHICH ARE OUT OF CONTROL OF NACHURS.

SELLER WARRANTS THAT THE ABOVE PRODUCT CONFORMS TO ITS CHEMICAL DESCRIPTION AND IS REASONABLY FIT FOR THE PURPOSE ON THE LABEL WHEN USED IN ACCORDANCE WITH DIRECTIONS UNDER NORMAL CONDITIONS OF USE (INCLUDING NORMAL WEATHER CONDITIONS). NEITHER THIS WARRANTY NOR ANY OTHER WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EXPRESS OR IMPLIED, EXTENDS TO THE USE OF THIS PRODUCT WHEN USED CONTRARY TO THE LABEL INSTRUCTIONS OR UNDER ABNORMAL CONDITIONS (INCLUDING ABNORMAL WEATHER CONDITIONS), AND THE BUYER ASSUMES THE RISK OF ANY SUCH USE. NACHURS STARTER OR FOLIAR APPLICATIONS ARE INTENDED TO SUPPLEMENT EXISTING SOIL FERTILITY PROGRAMS AND WILL NOT BY ITSELF PROVIDE ALL THE NUTRIENTS NORMALLY REQUIRED BY AGRICULTURAL CROPS.

© 2020. NACHURS ALPINE SOLUTIONS. All rights reserved. “NACHURS”, “NACHURS K-fuel”, and “Bio-K” are trademarks of NACHURS ALPINE SOLUTIONS.

Engenia is a registered trademarks of BASF. Enlist One and Enlist Duo are trademarks of TThe Dow Chemical Company (“Dow”) or an affiliated company of Dow. XtendiMax is a registered trademark of Bayer Group. Engenia is a registered trademarks of BASF.

BW-K ACEPREMIUM FOLIAR FERTILIZER

APPLICATION INSTRUCTIONS:BW-K ACE liquid fertilizer can be used on all field and specialty crops to aid in correcting or preventing potassium deficiencies. Potassium requirements for most crops increase greatly during periods of rapid growth and fruit development. Application of BW-K ACE should be made based on soil and plant tissue analysis for potassium.

FOLIAR – Apply by ground or air at a 2 to 12 quarts/acre rate in 3 to 10 gallons/acre of water on row crops. Specialty crops apply up to 6 quarts/acre for every 100 gallons of water.

FERTIGATION –

Center Pivot - Apply 0.5 to 5 gallons/acre as needed.Sprinkler - Trees, row crops and vegetables, apply 0.5 to 5 gallons/acre. Vines apply 0.5 to 4 gallons/acre. Drip Irrigation - 0.5 to 5 gallons per application.

SOIL – Apply 1/2 to 5 gallons/acre with other fertilizers at planting time. When using with seed applied starters take into consideration the total amount of salt allowed for your soil type.

For recommendations regarding specific crops or applications consult your BW FUSION Representative.

BW FUSION will assume no liability for this product if crop damage or if plugged fertigation equipment occurs from its use. BW FUSION always recommends a jar test for compatibility with irrigation water when used for fertigation.

PRODUCT BENEFITS:• Formulated with NACHURS® Bio-K® for

greater solubility and lowest salt index• Provides safe application reducing

plant stress• Superior source of K• Highly compatible with pesticides and

other fertilizer• High analysis• Non caustic or corrosive

PRECAUTIONS:Keep Out Of Reach Of Children.

May cause irritation or injury to eyes. Avoid contact with formulated product. Avoid prolonged exposure to vapor and spray mist. Harmful if swallowed.

To protect skin from exposure wear protective equipment such as rubber aprons, rubber gloves and boots. Wash thoroughly after handling. Always use product with adequate ventilation.

FIRST AID: In case of contact with eyes, immediately flush with water for at least 15 minutes. Seek medical attention if irritation occurs. In case of skin contact, flush with plenty of water. Seek immediate medical attention if irritation occurs.

Always wash contaminated clothing before reusing. If swallowed, give large amounts of water and induce vomiting. Seek medical attention.

v0.1 PRS F000352

APPROVED FOR USE WITHEngenia® • XtendiMax® • Enlist One® • Enlist Duo®

HERBICIDE TECHNOLOGIES

• Provide additional plant nutrition without extra application cost• Improves plant health and nutrient use efficiency• Excellent tank mix compatibility, but always jar test for verification

PATENTED

PATENTED POTASSIUM ACETATE TECHNOLOGY

IN-FURROW APPLICATION

BW FUSION liquid fertilizer placed on or near the seed at planting time can stimulate early root growth and strengthen young plants. See the reverse side for recommended rates of fertilizer. Consult with your authorized Dealer for specific fertility recommendations.

Additives to In-Furrow ApplicationsIn furrow placement of other crop enhancement products is greatly facilitated once the application kit for the application of starter products is installed on the planting implement. Crop protection products, biologicals, or plant growth supplements can often be added to the starter product for a very efficient and accurate method in applying these other products. All tank mixes should be tested for physical and performance compatibility before use. Consult with your BW FUSION retailer before using such mixes. The addition of an Injection kit to the application kit is often required to ensure product compatibilities.

THE FOLLOWING CONDITIONS MUST BE OBSERVED IN ORDER TO APPLY LIQUID FERTILIZER FOR FOLIAR APPLICATIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THE PLANTS.

• DO USE FERTILIZERS UNDER CONDITIONS OF OPTIMUM PLANT GROWTH INCLUDING HIGHEST HUMIDITY, MODERATE TEMPERATURE AND ADEQUATE SOIL MOISTURE.

• DO ADD, AS A MINIMUM, EQUAL AMOUNTS OF WATER. DO USE SUFFICIENT WATER TO PROVIDE THOROUGH COVERAGE.

• DO CONSULT WITH YOUR LOCAL SALES MANAGER TO DETERMINE PESTICIDES WHICH ARE COMPATIBLE WITH FERTILIZER.

• DO ADD WETTABLE OR SOLUBLE POWDERS, EMULSIFIABLES OR FLOWABLES TO WATER IN THE MIX AND WET, DISSOLVE OR DISPERSE BEFORE ADDING FERTILIZER.

• DO CONSULT YOUR LOCAL SALES MANAGER FOR RATE AND APPLICATION INSTRUCTIONS.

• DO USE A SMALL JAR OR CONTAINER PRIOR TO FULL SCALE MIXING TO PROPORTIONALLY MIX ALL THE COMPONENTS TO CONFIRM COMPATIBILITY.

• DO NOT USE WHEN THE CROP IS UNDER STRESS FROM PESTS, HEAT OR INADEQUATE SOIL MOISTURE.

• DO NOT APPLY BY AIRCRAFT IF SURFACE WIND IS GREATER THAN FIVE MILES PER HOUR TO ASSURE ADEQUATE CROP

COVERAGE AND DROPLET DISPOSITION.

• DO NOT SPRAY TO RUN OFF. DO NOT SPRAY TO VISIBLE

DROPLET COALESCENCE. DO NOT ALLOW CONCENTRATED

SPRAY MIST TO RUN OFF FRUIT OR LEAVES.

• DO NOT APPLY DURING THE HEAT OF THE DAY.

• DO NOT MIX WITH CALCIUM CONTAINING PRODUCTS UNLESS

THE CALCIUM IS FULLY EDTA CHELATED.

• DO NOT MIX FERTILIZERS WITH HARD WATER. MIXING WITH

HARD WATER MAY CAUSE CLOGGING OF LINES DUE TO THE

COMBINING OF CALCIUM, MAGNESIUM AND IRON IN THE

WATER WITH PHOSPHATE IN THE FERTILIZER.

FOLIAR APPLICATION

Foliar feeding is one of the most efficient methods of supplying nutrients during critical growing stages. BW FUSION foliar fertilizers provide available N-P-K and chelated micronutrients to make a good crop even better or it can supply a deficient, stressed crop the proper nutrients for a quick recovery. These products can also be customized and combined to ensure crop success.

BW FUSION foliars are manufactured with the highest quality raw materials on the market today and includes only available, chelated micronutrients to maximize foliar absorption. BW FUSION foliars can also be safely mixed with most insecticides, herbicides, and fungicides to help maximize yield potential (please follow proper mixing instructions).

PRODUCT STORAGE CONTAINER RECOMMENDATIONS

• Storage in poly, fiberglass, stainless, or lined/coated steel tanks to prevent possible product discoloration. Storage in flat bottom tanks is recommended during winter months. Bubble, recirculate, and/or agitate material before usage in all instances. Material stored in cone bottom tanks (although not recommended) will require longer recirculation after winter to regain product consistency.

• DO NOT STORE OR TRANSPORT ANY PRODUCT IN ALUMINUM, OR GALVANIZED STEEL TANKS

MIXING INSTRUCTIONS

BW FUSION liquid fertilizers can mix with many crop production products. Some non-100% EDTA chelates may not be compatible.

• In a small container prior to full scale mixing, proportionally mix all the components to confirm compatibility.

• Thorough mixing of all blends is important.• Temperature and storage time can influence the

degree of success.• Mix only the amount that will be immediately used.• Long-term storage is not suggested.

MIXING PROCEDURE

• Add ½ of total water to spray tank• Start recirculation in the tank• Add micronutrients and or any other flowable material• Add any soluble powder first pre-mixing with water• Add the recommended amount of liquid fertilizer• Add remaining water volume and continue

recirculation prior to spraying

For more specific foliar guidelines, consult with BW FUSION for fertility recommendations.

BW FUSION GENERAL RECOMMENDATIONS100% ORTHOPHOSPHATE LIQUID FERTILIZERS

v8.1

BW-K ACE

BW-K ACE


55560 150th Ave • Fonda, IA 50540712-288-6210


55560 150th Ave • Fonda, IA 50540712-288-6210

0-0-24PREMIUM LIQUID STARTER & FOLIAR FERTILIZER

GUARANTEED ANALYSIS

SOLUBLE POTASH (K20) ........................................... 24%


DENSITY/ WEIGHT PER GALLON: 10.65 LBS (4.83 kg) at 68°FALL COMPLETELY WATER SOLUBLE

®POWERED BY

0-0-24PREMIUM LIQUID STARTER & FOLIAR FERTILIZER

GUARANTEED ANALYSIS

SOLUBLE POTASH (K20) ........................................... 24%


DENSITY/ WEIGHT PER GALLON: 10.65 LBS (4.83 kg) at 68°FALL COMPLETELY WATER SOLUBLE

®POWERED BY

Information regarding the contents and levels of metals in this product is available on

the internet at http://www.aapfco.org/metals.htm

USE IN ACCORDANCE WITH RECOMMENDATIONS OF A QUALIFIED INDIVIDUAL OR INSTITUTION, SUCH AS, BUT NOT LIMITED TO, A CERTIFIED CROP ADVISOR, AGRONOMIST, UNIVERSITY PUBLICATION OR APPLY ACCORDING TO RECOMMENDATIONS IN YOUR APPROVED NUTRIENT MANAGEMENT PLAN. STARTER OR FOLIAR APPLICATIONS ARE INTENDED TO SUPPLEMENT EXISTING SOIL FERTILITY PROGRAMS AND WILL NOT BY ITSELF PROVIDE ALL THE NUTRIENTS NORMALLY REQUIRED BY AGRICULTURAL CROPS.

Seller warrants that this product conforms to the chemical description on the label. EXCEPT FOR THIS WARRANTY, THE PRODUCT IS FURNISHED “AS-IS”, AND NEITHER SELLER NOR MANUFACTURER MAKES ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE SELECTION, PURCHASE OR USE OF THIS PRODUCT; SELLER AND MANUFACTURER SPECIFICALLY DISCLAIM ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE BEYOND WHAT IS STATED ON THE LABEL. Buyer and User accept all risks arising from any use of this product, including without limitation, uses contrary to label instructions, or under conditions not reasonably foreseeable to (or beyond the control of) Seller or Manufacturer.

To the fullest extent permitted by law, neither Manufacturer nor Seller shall be liable for any incidental, consequential or special damages resulting from the use or handling of this product. THE EXCLUSIVE REMEDY OF THE BUYER OR USER, AND THE EXCLUSIVE LIABILITY OF MANUFACTURER AND SELLER, FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THIS PRODUCT, OR, AT THE ELECTION OF MANUFACTURER OR SELLER, THE REPLACEMENT OF THE PRODUCT.

WARNING: EXPOSURE MAY AGGRAVATE PRE-EXISTING EYE, SKIN, OR RESPIRATORY CONDITIONS.

“NACHURS ALPINE SOLUTIONS”, “NACHURS” “Bio-K”, are trademarks of NACHURS ALPINE SOLUTIONS. v0.1

© 2020. NACHURS ALPINE SOLUTIONS. All rights reserved. FL- F000529

Information regarding the contents and levels of metals in this product is available on

the internet at http://www.aapfco.org/metals.htm

USE IN ACCORDANCE WITH RECOMMENDATIONS OF A QUALIFIED INDIVIDUAL OR INSTITUTION, SUCH AS, BUT NOT LIMITED TO, A CERTIFIED CROP ADVISOR, AGRONOMIST, UNIVERSITY PUBLICATION OR APPLY ACCORDING TO RECOMMENDATIONS IN YOUR APPROVED NUTRIENT MANAGEMENT PLAN. STARTER OR FOLIAR APPLICATIONS ARE INTENDED TO SUPPLEMENT EXISTING SOIL FERTILITY PROGRAMS AND WILL NOT BY ITSELF PROVIDE ALL THE NUTRIENTS NORMALLY REQUIRED BY AGRICULTURAL CROPS.

Seller warrants that this product conforms to the chemical description on the label. EXCEPT FOR THIS WARRANTY, THE PRODUCT IS FURNISHED “AS-IS”, AND NEITHER SELLER NOR MANUFACTURER MAKES ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE SELECTION, PURCHASE OR USE OF THIS PRODUCT; SELLER AND MANUFACTURER SPECIFICALLY DISCLAIM ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE BEYOND WHAT IS STATED ON THE LABEL. Buyer and User accept all risks arising from any use of this product, including without limitation, uses contrary to label instructions, or under conditions not reasonably foreseeable to (or beyond the control of) Seller or Manufacturer.

To the fullest extent permitted by law, neither Manufacturer nor Seller shall be liable for any incidental, consequential or special damages resulting from the use or handling of this product. THE EXCLUSIVE REMEDY OF THE BUYER OR USER, AND THE EXCLUSIVE LIABILITY OF MANUFACTURER AND SELLER, FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THIS PRODUCT, OR, AT THE ELECTION OF MANUFACTURER OR SELLER, THE REPLACEMENT OF THE PRODUCT.

WARNING: EXPOSURE MAY AGGRAVATE PRE-EXISTING EYE, SKIN, OR RESPIRATORY CONDITIONS.

“NACHURS ALPINE SOLUTIONS”, “NACHURS” “Bio-K”, are trademarks of NACHURS ALPINE SOLUTIONS. v0.1

© 2020. NACHURS ALPINE SOLUTIONS. All rights reserved. FL- F000529

Bulk ShipmentSee Bill of Lading for Volume & Net Weight

Jug: 2.5 U.S. Gallons (9.46 L)Net Weight: 26.63 LBS (12.08 kg)

Box: 2 x 2.5 U.S. Gallons (2 x 9.46 L)Net Weight: 53.25 LBS (24.15 kg)

Tote:Volume: ________________

Net Weight: _____________

Bulk ShipmentSee Bill of Lading for Volume & Net Weight

Jug: 2.5 U.S. Gallons (9.46 L)Net Weight: 26.63 LBS (12.08 kg)

Box: 2 x 2.5 U.S. Gallons (2 x 9.46 L)Net Weight: 53.25 LBS (24.15 kg)

Tote:Volume: ________________

Net Weight: _____________

LOT #: ______________________________

LOT #: ______________________________

NAS - F352

NAS - F352



55560 150th Ave | Fonda, IA 50540 | 712-288-6210

20-0-7.5-5SSlow Release Nitrogen

PRINCIPAL FUNCTIONING AGENTS


Nitrogen………………………………………................................… 20% Urea Nitrogen……….......................................................……...6.0% Polymethylene Urea……...................................................…..14.0%Potash (K20)…………………………….................................…….. 7.5%Sulfur (S)………………………………....................................……. 5.0%

Harmful if swallowed. Avoid breathing vapor. Protect from freezing. Read entire label before using. Wash contami-nated clothing before reuse.

GENERAL INFORMATIONFoliar fertilization is intended as a supplement to a regular fertilization program and will not, by itself, provide all the nutrients normally required by most crops.

BW 20-0-7.5-5S is a clear liquid containing slow release nitrogen with a superior potassium and sulfur fertilizer solution. The slow release nitrogen means increased crop safety, in-creased nitrogen absorption, translocation and remobiliza-tion when used on field crops. BW 20-0-7.5-5S also provides a clear chloride free, safe and efficient source of potassium and sulfur. BW 20-0-7.5-5S mixes readily with liquid fertilizers, insecticides and herbicides.However, it is recommended that a compatibility test be used before mixing with specific fertilizers and pesticides.

PRODUCT APPLICATIONBW 20-0-7.5-5S may be applied as a foliar spray, soil applied or injected through a irrigation system. BW 20-0-7.5-5S may be applied to most field crops at a rate of up to 5 gallons per acre. Use a minimum of 5 gallons of water per acre. Various environmental and agronomic factors, such as crop stress associated with high temperatures and dry condi-tions, make it impossible to eliminate all risks associated with the use of this product.

PRECAUTIONARY STATEMENTSKeep out of reach of children. Do not get in eyes, on skin or on clothing. Wear goggles, face shield, or safety glasses & rubber gloves when handling. If eye exposure occurs get medical attention immediately.

FIRST AIDIF ON SKIN: Wash with soap and water for 10-15 minutes. If irritation persist, get medical attention.IF IN EYES: Flush with cool water for at least 15 minutes. Remove contact lenses if present and easy to do; continue rinsing. If irritation persist, get medical attention.IF INGESTED: Drink large amounts of water. DO NOT INDUCE VOMIT-TING. Get medical attention immediately or call a Poison Control Center. Do not give anything by mouth to an unconscious person.IF INHALED: Get person to fresh air. If unconscious get medical attention.

Have the product label with you when calling a doctor or going for treatment.

For Chemical Emergency: Call the POISON CONTROL CENTER at 800-222-1222

HANDLING AND STORAGEKeep container tightly closed. Store in a cool, well-ventilated location in vented tanks out of direct sunlight. Avoid containers, piping, or fittings made of aluminum, brass, bronze or copper bearing allows.

Plus 0.5% Sulfur


55560 150th Ave | Fonda, IA 50540 | 712-288-6210

25-0-0Plus 0.5% B - Controlled Release Nitrogen Foliar Fertilizer

PRINCIPAL FUNCTIONING AGENTS


Total Nitrogen (N) ............................................................................................25.00% 7.0% Urea Nitrogen 18.0% Other Water Soluble Nitrogen*Boron (B) ...........................................................................................................0.50%Derived from urea, methylene ureas, urea triazone, and boric acid.Chlorine (Cl), not more than 0.01%.*18.0% Slowly Available Nitrogen from methylene ureas and urea triazone.Chlorine (Cl), maximum……………...........................................................…… 8.00%

Before using this product, read all precautions, directions for use, conditions of sale – limited warranty and limitations of liability and remedies.

May cause slight irritation if allowed to directly contact skin or eyes. Do not take internally. Avoid contact with or inhalation of the spray mist. If product is being mixed with pesticides and/or spray adjuvants, follow all precautionary statements on the accompanying pesticide(s) and/or fertilizer label(s).

WARNING USE WITHIN 9 MONTHS FROM DATE OF PURCHASE.Contains Boron. Do not use on plants sensitive to Boron. Use of Boron on crops other than those recommended may result in serious injury to the crop.

Information regarding the content and levels of metals in this product is available onthe Internet at: http://www.aapfco.org/metals.htm

GENERAL INFORMATION0.63 lbs/gal of Nitrogen, out of 2.525 lbs/gal of the total Nitrogen in this product, is controlled release. 25-0-0 Plus 0.5% B is a unique foliar fertilizer that contains polymethylene urea solution, a patent pending, controlled release organic nitrogen source. 25-0-0 Plus 0.5% B is a foliar fertilizer intended as a supplement to a regular fertilizer program and will not by itself provide all the nutrients required by crops or other intended plants. Successful nitrogen application rates are dependent upon a number of factors, such as soil type, organic matter content, soil nitrate level, previous crop, irrigation or non-irrigation, variety, planting date, etc. Unexpected weather variations make preplant and/or early season nitrogen application rates difficult to recommend. To achieve efficiency, nitrogen fertilizer use should be considered as a dependent production variable. Total nitrogen applied will depend upon the needs of the developing plant and those environmental factors responsible for the production system in each field. Soil test recommendations and specific nitrogen rates are usually for average conditions only. For efficient nitrogen use, use starter fertilizer band applications during cultivation and foliar applications of 25-0-0 Plus 0.5% B.

FIRST AIDIF ON SKIN: Wash with soap and water for 10-15 minutes. If irritation persist, get medical attention.IF IN EYES: Flush with cool water for at least 15 minutes. Remove contact lenses if present and easy to do; continue rinsing. If irritation persist, get medical attention.IF INGESTED: Drink large amounts of water. DO NOT INDUCE VOMITTING. Get medical attention immediately or call a Poison Control Center. Do not give anything by mouth to an unconscious person.IF INHALED: Get person to fresh air. If unconscious get medical attention.

Have the product label with you when calling a doctor or going for treatment.

For Chemical Emergency: Call the POISON CONTROL CENTER at 800-222-1222

STORAGEPRODUCT MUST BE STORED AT TEMPERATURES ABOVE 45°F.Store in original container only. Keep container tightly closed, do not allow water to be introduced into the contents of this container. Do not contaminate water sources by runoff from cleaning of equipment, disposal of equipment washwater or spray waste.

GENERAL USE RATE RECOMMENDATIONSFIELD CROPSALFALFA(1): 4 - 6 qts. per acre. Apply after each cutting when sufficient foliage is present.CANOLA(1): 4 - 8 qts. per acre. Apply pre-bloom.CORN: 3 - 5 gallons per acre applied at V-5 to V-8 as a foliar application for use as a partial side-dress Nitrogen (N) replacement. 1- 3 gallons per acre applied as a foliar application at pre-tassel as a Nitrogen (N) supplement. 1-2 gallons per acre applied as a foliar application when used with fungicides, insecticides. Maximum replacement value of side-dress Nitrogen (N) using 25-0-0 Plus 0.5% B:3.0 gal. = 37.5 lbs. Nitrogen (N)4.0 gal. = 50.0 lbs. Nitrogen (N)5.0 gal. = 64.0 lbs. Nitrogen (N)CORN (SEED): 3 - 5 gallons per acre applied at V-5 to V-8 as a foliar application for use as a partial side-dress Nitrogen (N) replacement. 1- 3 gallons per acre applied as a foliar application at pre-tassel as a Nitrogen (N) supplement. 1-2 gallons per acre applied as a foliar application at when used with fungicides, insecticides. Maximum replacement value of side-dress Nitrogen (N) using 25-0-0 Plus 0.5% B:3.0 gal. = 37.5 lbs. Nitrogen (N)4.0 gal. = 50.0 lbs. Nitrogen (N)5.0 gal. = 64.0 lbs. Nitrogen (N)COTTON (SEEDLING): 3 - 4 qts. per acre. Apply when first true leaves appear. (AFTERSEEDLING STAGE): 2 - 4 qts. per acre. (BOLL DEVELOPMENT): 4 - 12 qts. per acre. Apply at early boll formation and repeat at 14 - 21 day intervals.FLAX: 6 - 10 qts. per acre. Apply at early boll development.GRAIN SORGHUM: 4 - 6 qts. per acre after pollination.GRASS (SEED PRODUCTION): 10 - 16 qts. per acre. Apply at seed head elongation.HOPS: 4 - 6 qts. per acre. Apply before cone development.PEANUTS: (Single Application) - 10 - 16 qts. per acre at early pod development. (Multiple Application) - 4 - 6 qts. per application at early bloom and repeat at 14 - 21 day intervals until pods are filled.


55560 150th Ave | Fonda, IA 50540 | 712-288-6210 NET CONTENTS: 2.5 GALLONS

25-0-0Plus 0.5% B

POTATOES: (Single Application) - 10 - 16 qts. per acre. Apply at mid tuber development.(Multiple Application) - 4 - 6 qts. per acre at tuber initiation and repeat at 10 - 14 day intervals until maximum tuber development has occurred.RICE: 6 - 10 qts. per acre. Apply at panicle emergence.SMALL GRAINS: Foliar application of 1 - 3 gallons per acre applied from spring greenup to early joint (Feekes 8) as a partial replacement of soil applied Nitrogen (N). 1 - 3 gallons per acre at or near flag leaf stage as a Nitrogen (N) supplement. Maximum replacement value for partial Nitrogen (N) replacement: 3.0 gal. = 30.0 lbs. Nitrogen (N). Certain conditions may change the Maximum replacement value, but only with the approval of your Helena Chemical Company sales representative using prior experience and local data.SOYBEANS: 1 – 3 gallons per acre as a Nitrogen (N) supplement. Apply at V6 – R4 growth stage.SUGAR BEETS(1): 10 qts. per acre. Apply at 10 - 12 leaf and repeat at 20 leaf.SUNFLOWER(1): 4 - 6 qts. per acre. Apply when outer seeds start to fill, repeat in 10 - 14 days.SWEET POTATOES: 4 - 6 qts. per acre. Apply at tuber initiation and repeat at 10 - 14days.TOBACCO(1): 6 - 10 qts. per acre. Apply at plant bed stage to near maturity as needed to maintain crop growth and quality.OTHER CROPS: 4 - 6 qts. per acre. Apply when sufficient foliage is present, try on a small area until more experience and trials have been completed to determine if higher rate is desirable.VEGETABLESASPARAGUS(1): 6 -1 0 qts. per acre. Apply beginning at mid-fern development, then at 14 -21 day intervals.BEANS (DRY): (Single Application) - 10 qts. per acre at early pod formation. (MultipleApplication) - 4 - 6 qts. per acre at early full flower and repeat in 10 - 14 days.BEANS (GREEN, LIMA): 4 - 6 qts. per acre at early flower and repeat in 7 - 10 days.BROCCOLI(1): 6 - 10 qts. per acre. Apply first application after thinning, then 3 weeksbefore head formation and repeat in 7 - 10 days.CABBAGE(1): 6 - 10 qts. per acre. Apply first application after thinning, then early head formation and repeat after 14 -21 days.CANTALOUPES: 6 - 10 qts. per acre. Apply at early flowering and repeat 7 - 10 days later.CAULIFLOWER(1): 6 - 10 qts. per acre. Apply first application after thinning or transplant, other applications at early head set and repeat at 10 - 14 day intervals.CELERY(1): 4 - 6 qts. per acre. Apply when plants are 8 - 12 inches tall and repeat at 10 - 14 day intervals.CORN (SWEET): 3 - 5 gallons per acre applied at V-5 to V-8 as a foliar application for use as a partial side-dress Nitrogen (N) replacement. 1- 3 gallons per acre applied as a foliar application at pre-tassel as a Nitrogen (N) supplement. 1-2 gallons per acre applied as a foliar application when used with fungicides, insecticides.Maximum replacement value of side-dress Nitrogen (N) using 25-0-0 Plus 0.5% B:3.0 gal. = 37.5 lbs. Nitrogen (N)4.0 gal. = 50.0 lbs. Nitrogen (N)5.0 gal. = 64.0 lbs. Nitrogen (N)CUCUMBERS: (Single Application) - 10 - 16 qts. per acre. Apply at early fruit set. (Multiple Applications) - 4 - 6 qts. per acre. Apply at early flowering and repeat at 10 - 14 dayintervals.LENTILS: 4 - 6 qts. per acre. Apply at early flowering and repeat at 10 - 14 day intervals.LETTUCE(1): 4 - 6 qts. per acre. Apply after thinning, then at early head formation and repeat at 10 - 14 day intervals.OKRA: 4 - 6 qts. per acre. Apply at bud stage and repeat at 10 - 14 day intervals.ONIONS: 4 - 6 qts. per acre. Apply at mid set development and repeat at 14 - 21 day intervals.

PEAS: 4 - 6 qts. per acre. Apply at early flowering and repeat in 10 - 14 days.PEPPERS(1): 4 - 6 qts. per acre. Apply at early fruit set and repeat in 10 - 14 days.SPINACH(1): 6 - 10 qts. per acre. Apply when sufficient foliage is present and repeat at 14 - 21 days.SQUASH: 6 - 10 qts. per acre. Apply at early fruit set and repeat at 10 - 14 day intervals.TOMATOES (PROCESS) (1): (Single Application) - 10 qts. per acre. Apply 10 - 14 days after full bloom. (Multiple Applications) - 4 - 6 qts. per acre at full bloom and repeat at 10 - 14 day intervals until harvest is near completion.WATERMELONS: 6 - 10 qts. per acre. Apply at early flowering and repeat 7 - 10 days later.OTHER CROPS: 4 - 6 qts. per acre. Apply when sufficient foliage is present, try on a small area until more experience and trials have been completed to determine if higher rate is desirable.COMMERCIAL CHRISTMAS TREES, ORNAMENTALS AND NURSERY STOCKApply 4 - 10* qts. per acre when sufficient foliage is present. 25-0-0 Plus 0.5% B has been applied undiluted to some types of ornamentals and nursery stock. Since these plants vary widely in growth habit and leaf texture, some types are more susceptible to leaf or tip burn than others. It is recommended that the user try only a few plants at undiluted or concentrated rates and observe for a week before general applications are made.*A rate of 10 qts. per acre is equivalent to 7.35 oz. per 1,000 square feet.FRUITS AND NUTSALMONDS: Apply 6 - 10 qts. per acre at full leaf. Repeat at early nut expansion.APPLES(1): Apply 4 - 6 qts. per acre prior to fruit set or post harvest.CANEBERRIES: Apply 4 - 6 qts. per acre prior to fruit set.CHERRIES: Apply 4 - 6 qts. per acre prior to fruit set.CITRUS: Apply 4 - 6 qts. per acre at early bloom and repeat after fruit set.CRANBERRIES: Apply 4 - 6 qts. per acre at hook stage and repeat after fruit set.FILBERTS: (Single Application) - Apply 10 - 16 qts. per acre at early nut filling.(Multiple Applications) - 4 - 6 qts. per acre at early leaf expansion and repeat at 14 - 21 day intervals.GRAPES: Apply 2 - 4 qts. per acre prior to fruit set.PEACHES/NECTARINES: Apply 6 -1 0 qts. per acre prior to fruit set.PEARS: Apply 4 - 6 qts. per acre prior to fruit set or postharvest.PECANS: Apply 4 - 6 qts. per acre at full leaf. Repeat at early nut expansion.PLUMS: Apply 6 - 10 qts. per acre prior to fruit set.OLIVES: Apply 4 - 6 qts. per acre at early fruit development and repeat as required.STRAWBERRIES: Apply 2 - 3 qts. per acre at early flowering and repeat every 14 days through harvest. Initiate fall application when new growth reaches 3 inches in height.OTHER CROPS: 4 - 6 qts. per acre. Apply when sufficient foliage is present, try on a small area until more experience and trials have been completed to determine if higher rate is desirable.

Nutritional Performance and Protection · Micronutrient deficiencies usually occur when plants are...

Documents

Transcript of Nutritional Performance and Protection · Micronutrient deficiencies usually occur when plants are...