NuStar Logistics, L.P....NuStar Logistics, L.P. Product Specifications Central West i September15,...
Transcript of NuStar Logistics, L.P....NuStar Logistics, L.P. Product Specifications Central West i September15,...
NuStar Logistics, L.P.
Product Specifications
Central West
i September15, 2014
Central West
Product Specifications ii September 15, 2014
Table of Contents
Page
Central West Products Shipped by Pipeline v
ARIZONA GASOLINE
84 OCTANE CONVENTIONAL GASOLINE- TUSCON 1,2
ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 X2 3,4
ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 X3 5 ARIZONA CLEANER BURNING GASOLINE (AZRBOB) GRADE 26 X6 6,7
ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 30 X5 8,9
ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z2 10
ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z3 11
ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z5 12,13 ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z6 14,15
AVIATION JET FUEL
JP-8 GRADE MILITARY JET FUEL GRADE 05 16-20
QGRADE COMMERCIAL JET FUEL 21,22
CALIFORNIA GASOLINE
CARB PREMIUM GASOLINE GRADE 33 24
CARB PREMIUM GASOLINE GRADE 34 25
CARB PREMIUM GASOLINE GRADE 36 26
CONVENTIONAL GASOLINE BLENDSTOCKS
85 OCT INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) 27,28
86 OCT INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) 29,30
86 OCT INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB)
- GRADE 08 31,32
PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) - 90 OCTANE 33,34
PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB)
- 91 OCTANE 35,36
PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB)
- GRADE 22 37,38
Central West
Product Specifications iii September 15, 2014
CONVENTIONAL GASOLINES Page
85 OCTANE CONVENTIONAL GRADE GASOLINE 39 86 OCTANE CONVENTIONAL GRADE GASOLINE 40,41 87 OCTANE CONVENTIONAL GRADE GASOLINE GRADE 03 42,43 90 OCTANE CONVENTIONAL GRADE GASOLINE 44,45 91 OCTANE CONVENTIONAL GRADE GASOLINE 46,47 93 OCTANE CONVENTIONAL GRADE GASOLINE GRADE 01 48,49
DISTILLATES
FUNGIBLE ULTRA LOW SULFUR DIESEL GRADE 37
50,51 LOW SULFUR HIGHWAY DIESEL FUEL GRADE 06 52,53 SEGREGRATED DISTILLATE BLENDSTOCK 54 SEGREGRATED DISTILLATE BLENDSTOCK GRADE 43 TEXAS X GRADE ULTRA LOW EMISSION DIESEL FUEL GRADE 49
55 90
LIQUIFIED PETROLEUM GAS
L GRADE PROPANE GRADE 12
56
REFORMULATED GASOLINE
93 OCTANE INDEX REFORMULATED GASOLINE
57,58
REFORMULATED GASOLINE BLENDSTOCKS
87 OCT INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB)
87 OCT INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB)
- GRADE 21
59,60
61,62
GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB) 63,64 NR GRADE GASOLINE BLENDSTOCK (RBOB) GRADE 21 65,66 PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)
PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)
- GRADE 22
67,68
69,70,71
SPECIALTY PRODUCTS
LIGHT NAPHTHA
72
Central West
Product Specifications iv September 15, 2014
ADDITIVES Page
GASOLINE, FUEL OIL AND DIESEL FUEL ADDITIVE SPECIFICATIONS 73,74
GASOLINE VOLATILITY SCHEDULES
AMARILLO 8” PIPELINE - PREMIUM UNLEADED GASOLINE 75
AMARILLO 8” PIPELINE - REGULAR UNLEADED GASOLINE 76
COLORADO SPRINGS PIPELINE – PREMIUM UNLEADED GASOLINE 77
COLORADO SPRINGS PIPELINE – REGULAR UNLEADED GASOLINE 78
EL PASO PIPELINE – PREMIUM UNLEADED GASOLINE 79 EL PASO PIPELINE – REGULAR UNLEADED GASOLINE 80
LAREDO PIPELINE – PREMIUM UNLEADED GASOLINE 81
LAREDO PIPELINE – REGULAR UNLEADED GASOLINE 82
SAN ANTONIO EAST PIPELINE – PREMIUM UNLEADED GASOLINE 83
SAN ANTONIO EAST PIPELINE – REGULAR UNLEADED GASOLINE 84
SAN ANTONIO SOUTH PIPELINE – PREMIUM UNLEADED GASOLINE 85 SAN ANTONIO SOUTH PIPELINE – REGULAR UNLEADED GASOLINE 86
V- SEASONAL GASOLINE VOLATILITY CLASSES 87
VALLEY PIPELINE – PREMIUM UNLEADED GASOLINE 88
VALLEY PIPELINE – REGULAR UNLEADED GASOLINE 89
Central West Products Shipped by Pipeline System
Product Name TOC Category Shipped on CW Pipeline System CW Pipeline Systems 84 OCTANE CONVENTIONAL GASOLINE - TUSCON Arizona Gasolines 9 Aberathy/Lubbock Pipeline 1
ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 PRODUCT CODE X2 Arizona Gasolines 9 Albuquerque Pipeline 2 ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 PRODUCT CODE X3 Arizona Gasolines 9 Amarillo - 6" Pipeline 3
ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 26 PRODUCT CODE X6 Arizona Gasolines 9 Amarillo - 8" Pipeline 4 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 30 PRODUCT CODE X5 Arizona Gasolines 9 Borger-Denver Pipeline 5 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z2 Arizona Gasolines 9 Burgos Pipeline 6 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z3 Arizona Gasolines 9 Colorado Springs- Denver Pipeline 7 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z5 Arizona Gasolines 9 Corpus Christi Chemical Pipeline 8 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z6 Arizona Gasolines 9 El Paso Pipeline 9
JP-8 GRADE MILITARY JET FUEL GRADE 05 Aviation/Jet Fuel 13 Laredo Pipeline 11 Q GRADE COMMERCIAL JET FUEL Aviation/Jet Fuel 2,4,5,7 San Antonio South Pipeline 12
T GRADE TURBINE FUEL GRADE 14 Aviation/Jet Fuel 1,2,4,5,7,8,12,13 Southlake Pipeline 13 CARB PREMIUM GASOLINE GRADE 36 California Gasolines 9 TR-Pettus-SA East Pipeline 14 CARB REGULAR GASOLINE GRADE 33 California Gasolines 9 Valley Pipeline 15 CARB REGULAR GASOLINE GRADE 34 California Gasolines 9
85 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) Conventional Gasoline Blendstocks 4,5,7 86 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) Conventional Gasoline Blendstocks 1,9
87 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) – GRADE 08 Conventional Gasoline Blendstocks 11,12,14 PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) – 90 OCTANE Conventional Gasoline Blendstocks 1,4 PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) – 91 OCTANE Conventional Gasoline Blendstocks 2,4,5,7 PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) – GRADE 22 Conventional Gasoline Blendstocks 11,12,14
85 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 5,7 86 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 1,4,9
87 OCTANE INDEX CONVENTIONAL GASOLINE GRADE 03 Conventional Gasolines 11,12,15 90 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 1,4,15 91 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 1,2,4
93 OCTANE INDEX CONVENTIONAL GASOLINE GRADE 01 Conventional Gasolines 11,12,15 FUNGIBLE ULTRA LOW SULFUR FUEL DIESEL GRADE 37 Distillates 1,2,3,4,5,7,9,13
LOW SULFUR HIGHWAY DIESEL FUEL GRADE 06 Distillates 12 SEGREGATED DISTILLATE BLENDSTOCK Distillates 8
L GRADE PROPANE GRADE 12 Liquified Petroleum Gas 9,11 93 OCTANE INDEX REFORMULATED GASOLINE Reformulated Gasoline 13
87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB) Reformulated Gasoline Blendstocks 13 87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB) GRADE 21 Reformulated Gasoline Blendstocks 13
GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB) Reformulated Gasoline Blendstocks 13 NR GRADE GASOLINE BLENDSTOCK (RBOB) GRADE 21 Reformulated Gasoline Blendstocks 13
PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB) Reformulated Gasoline Blendstocks 13 PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB) – GRADE 22 Reformulated Gasoline Blendstocks 13
LIGHT NAPHTHA Specialty Products 6,15
Central West
Pipeline Specifications v December 1, 2011
Central West
Product Specifications Page 1 December 1, 2011
SPECIFICATIONS FOR 84 OCTANE CONVENTIONAL GASOLINE - TUCSON
84TUC
Product code H6 thru H9 (1) (2) (3)
Product Codes 6H thru 9H (1) (2) (3)
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility, (EPA formula) D4953 (1) D5191 Distillation, deg F D86
End point, F 437 Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 84.0 Sulfur, ppm D2622 80* Haze rating 3/ D4176 2 3 NACE Corrosion TM0172 B+
Central West
Product Specifications Page 2 December 1, 2011
SPECIFICATIONS FOR 84 OCTANE CONVENTIONAL GASOLINE - TUCSON
84TUC
*NOTE: Registered Small Refiners may ship SRGAS with a sulfur content not to exceed their
permissible cap per EPA regulations. SRGAS product codes will be the Numeric/Alpha reverse of
their low sulfur counterparts. SRGAS may be delivered fungible with its low sulfur counterpart
(i.e., H9=9H, etc.).
1/ RVP: H6/6H = 10.00, H7/7H = 11.5, H8/8H = 13.5, H9/9H = 9.0
2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
3/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max
In addition to the above specifications, product must meet latest revision of ASTM D4814.
Maximum oxygen content is 0.05 weight%.
Rev. 2 03/29/2011
Central West
Product Specifications Page 3 December 1, 2011
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 6.40 7.00
D5191 Distillation, deg F D86
E200 30% 70% E300 70% 100% End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.003 0.005
Lead, g/gal D3237 0.030 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 87.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50% Olefins, vol % D4815 25% Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3
NACE Corrosion TM0172 B+
SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE (CBG)
GRADE 30 - Product code X2 (1) (2)
Central West
Product Specifications Page 4 December 1, 2011
SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE (CBG) 1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
In addition to the above specifications, product must meet latest revision of ASTM D4814.
Rev. 1
3/13/09
Central West
Product Specifications Page 5 December 1, 2011
SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE (CBG)
GRADE 30 - Product code X3 (1)
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00
D5191 Distillation, deg F D86
E200 30% 70% E300 70% 100% End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.003 0.005
Lead, g/gal D3237 0.030 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 87.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50% Olefins, vol % D4815 25% Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3
NACE Corrosion TM0172 B+
1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
In addition to the above specifications, product must meet latest revision of ASTM D4814. Rev. 1 3/13/09
Central West
Product Specifications Page 6 December 1, 2011
SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE
AZRBOB
GRADE 26 - Product code X6 (1) (2) (3)
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00 D5191 Distillation, deg F D86
T50 237 T90 335 End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 84.0 Sulfur, ppm D2622 89 Aromatics, vol % D5580 33.1 Olefins, vol % D4815 11.1 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+
Central West
Product Specifications Page 7 December 1, 2011
SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE
AZRBOB
1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max In addition to the above specifications, product must meet latest revision of ASTM D4814.
AZRBOB does not comply with the standards for Arizona CBG without the addition of oxygenate.
This AZRBOB is intended for blending with 10 vol% ethanol and may not be combined with AZRBOBs requiring oxygenate
blending with any other type or amount of oxygenate.
Rev. 1 3/13/09
Central West
Product Specifications Page 8 December 1, 2011
SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE
AZRBOB
GRADE 30 - Product code X5 (1) (2)
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00 D5191 Distillation, deg F D86
T50 237 T90 335 End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 87.0 Sulfur, ppm D2622 89 Aromatics, vol % D5580 33.1 Olefins, vol % D4815 11.1 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+
SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE
AZRBOB
1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max In addition to the above specifications, product must meet latest revision of ASTM D4814.
For shipment in the Spring transition only.
AZRBOB does not comply with the standards for Arizona CBG without the addition of oxygenate.
This AZRBOB is intended for blending with 10 vol% ethanol and may not be combined with AZRBOBs requiring oxygenate
blending with any other type or amount of oxygenate.
Rev. 1
3/13/09
Central West Product Specifications Page 9 December 1, 2011
December 1, 2011
Central West
Product Specifications Page 10
SPECIFICATIONS FOR PREMIUM ARIZONA CLEANER BURNING GASOLINE
AZRBOB
GRADE 31 - Product code Z2 (1)
ASTM Origin Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 6.4 7.00 D5191 Distillation, deg F D86
E200 30% 70% E300 70% 100% End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 91.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50 Olefins, vol % D4815 25 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+
1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max
In addition to the above specifications, product must meet latest revision of ASTM D4814.
Rev. 2 03/29/2011
December 1, 2011
Central West
Product Specifications Page 11
SPECIFICATIONS FOR PREMIUM ARIZONA CLEANER BURNING GASOLINE
AZRBOB
GRADE 31 - Product code Z3 (1) (2)
ASTM Origin Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00 D5191 Distillation, deg F D86
E200 30% 70% E300 70% 100% End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 91.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50 Olefins, vol % D4815 25 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+
1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max
In addition to the above specifications, product must meet latest revision of ASTM D4814.
Rev. 2 03/29/2011
December 1, 2011
Central West
Product Specifications Page 12
SPECIFICATIONS FOR PREMIUM ARIZONA CLEANER BURNING GASOLINE
AZRBOB
GRADE 31 - Product code Z5 (1) (2) (3) (4)
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00 D5191 Distillation, deg F D86
T50 237 T90 335 End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 91.0 Sulfur, ppm D2622 89 Aromatics, vol % D5580 33.1 Olefins, vol % D4815 11.1 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+
1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max
In addition to the above specifications, product must meet latest revision of ASTM D4814.
For shipment in Spring and Fall transitions only.
SPECIFICATIONS FOR PREMIUM ARIZONA CLEANER BURNING GASOLINE
AZRBOB
AZRBOB does not comply with the standards for Arizona CBG without the addition of oxygenate.
This AZRBOB is intended for blending with 10 vol% ethanol and may not be combined with AZRBOBs requiring oxygenate
blending with any other type or amount of oxygenate.
Rev. 1
3/13/09
Central West Product Specifications Page 13 December 1, 2011
SPECIFICATIONS FOR PREMIUM ARIZONA CLEANER BURNING GASOLINE
AZRBOB
GRADE 31 - Product code Z6 (1) (2) (3)
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00 D5191 Distillation, deg F D86
T50 237 T90 335 End point, F 437
Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 88.5 Sulfur, ppm D2622 89 Aromatics, vol % D5580 33.1 Olefins, vol % D4815 11.1 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+
1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
In addition to the above specifications, product must meet latest revision of ASTM D4814.
AZRBOB does not comply with the standards for Arizona CBG without the addition of oxygenate.
Central West Product Specifications Page 14 December 1, 2011
December 1, 2011
Central West
Product Specifications Page 15
SPECIFICATIONS FOR PREMIUM ARIZONA CLEANER BURNING GASOLINE
AZRBOB
This AZRBOB is intended for blending with 10 vol% ethanol and may not be combined with AZRBOBs requiring oxygenate
blending with any other type or amount of oxygenate.
Rev. 2
03/29/2011
December 1, 2011
Central West
Product Specifications Page 16
Gravity, API D287 37.0 51.0
Density, kg/L at 60F D4052 0.775 0.840
Total Acid Number, mg KOH/g D3242 0.015
Freezing Point, F D2386 -52
Existent Gum, mg/100ml D381 7.0
Sulfur, ppm D2622 3000
Mercaptan Sulfur, wt.% D3227 0.002
Doctor Test D4952 Negative
Color, Saybolt D156 Report
Corrosion, Copper D130 1
Water Separation Index D3948 1/ Water Reaction, Interface Rating D1094 1b
Aromatics, vol. % D1319 25.0
Flash Point, F D93 100 Viscosity @ -4 F, cSt D445 8.0
Electrical Conductivity, pSm D2624 2/ 2/
Thermal Stability; D3241 3/ Filter pressure drop, mm Hg. 25 Heater tube deposit rating < 3
Distillation, F @ 760 mm Hg D86 Initial Boiling Point, F Report 10% Recovered, F 401 20% Recovered, F Report 50% Recovered, F Report 90% Recovered, F Report Final Boiling Point, F 572 Residue, Vol. % 1.5 Loss, Vol. %
OR 1.5
Simulated Distillation D2887 Initial Boiling Point, F Report 10% Recovered, F 401 20% Recovered, F Report 50% Recovered, F Report
SPECIFICATIONS FOR JP-8 GRADE MILITARY JET FUEL
Grade 05
ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be*
December 1, 2011
Central West
Product Specifications Page 17
SPECIFICATIONS FOR JP-8 GRADE MILITARY JET FUEL
Grade 05
90% Recovered, F Report
Final Boiling Point, F 572
Net Heat of Combustion, BTU/lb D3338 18,400
OR: MJ/kg D4809 42.8
Combustion
(1) Smoke Point, mm D1322 25.0
OR
(2) Smoke Point, mm D1322 19.0 3.0 AND Napthalenes vol. % D1840
Hydrogen Content, wt % D3701 13.4
Cetane Index D976 Report Particulate Matter, mg/L D5452 4/ 1.0
Filtration Time, minutes 15
Fuel System Icing Inhibitor, vol % D5006 5/ 0.10 0.15
1/ The minimum microseparometer rating shall be as follows:
J8 Additives MSEP Rating, min.
Antioxidant (AO)*, Metal Deactivator (MDA)* 90
AO*, MDA*, and Fuel System Icing Inhibitor (FSII) 85
AO*, MDA*, and Corrosion Inhibitor/Lubricity Improver (CI/LI) 80
AO*, MDA*, FSII and CI/LI 70
* Even though the presence or absence does not change these limits, samples submitted
for specification conformance testing shall contain the same additives present in the
refinery batch. Regardless of which minimum the refiner elects to meet, the refiner shall
report the MSEP rating on a laboratory hand blend of the fuel with all additives required
by the specification.
2/ The conductivity must be between 150 and 450pS/m at ambient temperature or 85 F,
whichever is lower (150 to 700 for JP8+100 shipments that contain thermal stability
improver additive), unless otherwise directed by the procuring activity.
3/ ASTM D3241 Thermal Stability test must be conducted at 260 C for 2.5 hours.
Peacock or abnormal color deposits result in a failure and are not accepted.
December 1, 2011
Central West
Product Specifications Page 18
SPECIFICATIONS FOR JP-8 GRADE MILITARY JET FUEL
Grade 05 4/ A minimum sample size of 3.79 liters (one gallon) shall be filtered. Filtration time will
be determined in accordance with the procedure in Appendix A of MIL-DTL-83133E (or
most current version); this procedure may be used to determine the particulate matt er as
an alternate to ASTM D5452 or ASTM D2276.
5/ FSII test shall be performed using the DiEGME scale of the refractometer.
Other Requirements
Additives: Shipper must provide the type and amount of each additive used upon request.
Antioxidants: Immediately after processing, and before the fuel is exposed to the atmosphere
(i.e. during rundown into feed/batch tankage), add an approved antioxidant from the following list in order to prevent the formation of gums and peroxides after manufacture. The
concentration of antioxidant to be added shall be:
a. Not less than 17.2 mg or more than 24.0 mg of active ingredient per liter of fuel (6.0
to 8.4 lb/1000 barrels) to all JP-8 fuel that contains blending stocks that have been
hydrogen treated.
b. At the option of the supplier, not more than 24.0 mg of active ingredient per liter of
fuel (8.4 lb/1000 barrels) may be added to JP-8 fuels that do not contain hydrogen
treated blending stocks.
Approved Antioxidants
a. 2, 6-di-tert-butyl-4-methylphenol
b. 6-tert-butyl-2, 4-dimethylphenol
c. 2, 6-di-tert-butylphenol
d. 75% minimum: 2, 6-di-tert-butylphenol
25% maximum: tert-butyl phenols and tri-tert-butylphenols
e. 72% minimum: 6-tert-butyl-2, 4-dimethylphenol
28% maximum: tert-butyl-methylphenols and tert-butyl dimethylphenols
f. 55% minimum: 2, 4-dimethyl-6-tert-butylphenol and 15% minimum: 2, 6-di-tert-butyl—4-methylphenol and
30% maximum: mixed methyl and dimethyl tert-butylphenols
Metal Deactivator: A metal deactivator, N,N’-disalycylidene-1, 2-propanediamine, may be
blended into the fuel. The concentration of active material used on initial batching of the fuel at
December 1, 2011
Central West
Product Specifications Page 19
SPECIFICATIONS FOR JP-8 GRADE MILITARY JET FUEL
Grade 05 the refinery shall not exceed 2.0 mg/L. Cumulative addition of metal deactivator when redoping
the fuel shall not exceed 5.7 mg/L. Metal deactivator additive shall not be used in JP -8 unless
the supplier has obtained written consent from the Procuring Activity and user.
Static Dissipater Additive: An additive shall be blended into the fuels in sufficient
concentration to increase the conductivity of the fuel to within the range specified in the
specifications at the point of injection. The point of injection of the additive shall be determined
by agreement between the purchasing authority and the supplier. The following electrical
conductivity additive is approved: Statis 450 marketed by Octel America Inc., Newark, DE
19702.
Corrosion Inhibitor: A corrosion inhibitor conforming to MIL-PRF-25017 shall be blended
into the F-34 (JP-8) grade fuel by the contractor. The corrosion inhibitor additive is optional for
F-35. The amount added shall be equal or greater than the minimum effective concentration an d
shall not exceed the maximum allowable concentration listed in the latest revision of QPL-
25017. The contractor or transporting agency, or both, shall maintain and upon request shall
make available to the Government evidence that the corrosion inhibitors used are equal in every
respect to the qualification products listed in QPL-25017. The point of injection of the corrosion
inhibitor shall be determined by agreement between the Purchasing Authority and the supplier.
Fuel System Icing Inhibitor (FSII): the use of a fuel system icing inhibitor shall be mandatory
for NATO F-34 (JP-8) and shall conform to MIL-DTL-85470. the point of injection of the
additive shall be determined by agreement between the Purchasing Authority and the supplier.
Thermal Stability Improver Additive: Due to logistical concern, personnel at the operating
location shall request written approval from the cognizant activity to add a thermal stability
improver additive to the fuel. If approval is given, the concentration of the a dditive and location
of injection shall be specified by the cognizant service activity found in MIL-DTL-8133E section
3.3.6. JP-8 fuel with an approved thermal stability improver additive at the required
concentration shall be designated as JP-8+100. Thermal stability improver additive shall not be
used in JP-8 without approval, in writing (reference MIL-DTL-83133E section 3.3.6 for
addresses).
December 1, 2011
Central West
Product Specifications Page 20
SPECIFICATIONS FOR JP-8 GRADE MILITARY JET FUEL
Grade 05
Qualified thermal stability improver additives:
Qualification
Additive name Reference Manufacturer
SPEC AID 8Q462 AFRL/PRSF BetzDeraborn
Ltr, 9 Dec 97 9669 Grogan Mill Road
PO Box 4300
The Woodlands, TX 77387
AeroShell Performance AFRL.PRSF Shell Aviation
Additive 101 Ltr, 13 Jan 98 Shell-Mex House
Strand
London WC2R 0ZA
Premixing of Additives: Additives shall not be premixed with other additives before injection
into the fuel so as to prevent possible reactions among the concentrated forms of different
additives.
Workmanship: At the time of Government acceptance, the finished fuel shall be visually free
from undissolved water, sediment, or suspended matter and shall be clear and bright.
Additional Provisions: The Carrier shall not be responsible for the concentrations of additives
in JP-8 grade jet fuel deliveries except as provided for in the tariff.
Rev. 1 3/13/09
SPECIFICATION FOR Q GRADE COMMERCIAL JET FUEL
ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be*
Gravity, API D287 37.5 50.5 0.5 lower
or higher
Acidity, Total, Mg KOH/g D3242 0.1
Freezing Point, F D2386, D5972 -40
Existent Gum, mg/100ml D381 5 7
Sulfur, Total, ppm D2622 3000
Mercaptan Sulfur, ppm 1/ D3227 30
Color, Saybolt D156 +16 +14
Corrosion, Copper D130 1
2 hours @ 212 F
Water Separation Index D3948 85 75
Water Reaction, D1094
Volume Change, ml +1
Interface Rating 1b
Aromatics, vol. % D1319 25
Net Heat of Combustion, BTU/lb 2/ D4809 18,400 D3338, D4529
Flash Point, F D56 108 100
Viscosity @ -4 F, cSt D445 8
Electrical Conductivity, pSm D2624 Report
Thermal Stability; D3241 3/ 4/
Filter pressure drop, mm Hg. 25
Heater tube rating < 3
Distillation, F @ 760 mm Hg D86
10% Recovered, F 396 400
50% Recovered, F Report
90% Recovered, F Report
Final Boiling Point, F 562 572
Residue, Vol. % 1.5
Loss, Vol. % 1.5
OR
Simulated Distillation D2887
10% Recovered, F 365
50% Recovered, F Report
90% Recovered, F Report
Final Boiling Point, F 644
Central West Product Specifications Page 21 December 1, 2011
SPECIFICATION FOR Q GRADE COMMERCIAL JET FUEL Combustion
(1) Smoke Point, mm D1322 25
OR
(2) Smoke Point, mm D1322 18
AND Napthalenes vol. % D1840 3.0
Particulate Matter D5452 Report
1/ The Mercaptan Sulfur determination may be waived if the result of a Doctor Test by
ASTM D4952 is negative.
2/ Equation 2 in D3338 may be used as an alternate method.
3/ ASTM D3241 Thermal Stability test must be conducted at 262 C for 2.5 hours at origin.
Peacock or abnormal color deposits result in a failure and are not accepted.
4/ ASTM D3241 Thermal Stability test results for deliveries will be generated at a
minimum test temperature of 260 C.
Additives:
Antioxidants: Shipments may, but are not required to, contain a maximum of 8.4 pounds
per 1,000 barrels (not including weight of solvent) of the following anti -oxidants:
(1) N, N-diisopropylparaphenylene diamine.
(2) 75% (min) of 2, 6-ditertiary-butyl phenol plus 25% (max) of tertiary and
tritertiary butyl phenols.
(3) 72% (min) 2, 4-dimethyl-6-tertiary-butyl phenol plus 28% (max) of monomethyl
and dimethyl tertiary-butyl phenols.
(4) 55% (min) 2, 4-dimethyl-6-tertiary-butyl phenol plus 45% (max) of mixed tertiary
and ditertiary butyl phenols.
Metal Deactivators: Shipments may, but are not required to, contain the following metal
deactivators at a maximum of 2.0 lbs per 1,000 barrels (not including weight of solvent):
(1) n, N-disalicylidene-1, 2-propane diamine.
No other additives are permitted.
The carrier shall not be responsible for the concentration of additives in jet fuel deliveries at
terminals.
Rev.1
3/13/09
Central West Product Specifications Page 22 December 1, 2011
Central West
Product Specifications
Page 23 December 1, 2011
SPECIFICATION FOR T GRADE TURBINE FUEL
Grade 14 ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be* Gravity, API D287 37.0 51.0
Freezing Point, F D2386 -40
Existent Gum, mg/100ml D381 7 Sulfur, ppm D2622 3000
Corrosion, Copper D130 1 Water Separation Index D3948 85
Flash Point, F D56 105 100
Distillation, F @ 760 mm Hg D86 Initial Boiling Point, F Report
10% Recovered, F 401 20% Recovered, F Report
50% Recovered, F Report 90% Recovered, F Report
Final Boiling Point, F 572
Residue, Vol. % 1.5
Loss, Vol. % 1.5
OR Simulated Distillation D2887
Initial Boiling Point, F Report
10% Recovered, F 401 20% Recovered, F Report
50% Recovered, F Report 90% Recovered, F Report
Final Boiling Point, F 572
Particulate Matter, mg/L D5452 1/ 2.0 Workmanship Clear and Bright
1/ A minimum sample size of 3.79 liters (one gallon) shall be filtered. Filtration time will be
determined in accordance with the procedure in Appendix A of MIL-DTL-83133E (or most
current version); this procedure may be used to determine the particulate matter as an alternate to
ASTM D5452 or ASTM D2276.
In addition to above specifications, product must meet ASTM D1655 latest revision.
Any included additives approved for use in ASTM D1655 must be declared by type and volume.
Rev. 1
3/13/09
Central West
Product Specifications Page 24 December 1, 2011
SPECIFICATIONS FOR CARB REGULAR GASOLINE
Grade 33
This product requires the addition of 5.7 vol.% ethanol.
ASTM Origin
Test 1/ Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed
Volatility 2/ D323 12.5 - Jan. 1st
5.99 - Feb. 1st
10.5 - Nov. 1st
12.5 - Dec. 1st
Distillation, degrees F D86-99ae1 Feb 1st
Nov.1st
Dec 1st
T50, max 232 237 237 T90, max 335 335 335
End point, max 437 437 437 Phosphorous, g/gal D3231 0.005
Lead, g/gal D3237 0.030
Research Octane {R} D2699 Report
Motor Octane {M} D2700 Report
(R+M)/2 D4814 87.0 Benzene, vol.% D5580-95 1.22
Aromatic HC, vol.% D5580-00 38.7 Olefins, vol.% D4815-99 0.025
Sulfur, ppm D2622-94 32
D5453-93 Oxygen, wt % D4815-99 0.25
Haze rating 4/ D4176 2 3 Odor 3/ Nonoffensive
1/ California Air Resources Board Regulations.
2/ Grabner-CA equation (RVPE psi = 0.972 * ptot – 0.71)
3/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt % dicyclopentadiene will
not be accepted for shipment.
4/ In addition to Nustar specifications, product must meet latest revision of ASTM D4814.
Rev. 1
3/13/09
Central West
Product Specifications Page 25 December 1
SPECIFICATIONS FOR CARB SUBGRADE GASOLINE
Grade 34
This product requires the addition of 5.7 vol.% ethanol.
ASTM Origin Test 1/ Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed
Volatility 2/ D323 12.5 - Jan. 1st
5.99 - Feb. 1st
10.5 - Nov. 1st
12.5 - Dec. 1st
Distillation, degrees F D86-99ae1 Feb 1st
Nov.1st
Dec 1st
T50, max 232 237 237
T90, max 335 335 335
End point, max 437 437 437 Phosphorous, g/gal D3231 0.005
Lead, g/gal D3237 0.030
Research Octane {R} D2699 Report
Motor Octane {M} D2700 Report
(R+M)/2 D4814 84.0 Benzene, vol.% D5580-95 1.22
Aromatic HC, vol.% D5580-00 38.7
Olefins, vol.% D4815-99 0.025
Sulfur, ppm D2622-94 32
D5453-93
Oxygen, wt % D4815-99 0.25 Haze rating 4/ D4176 2 3
Odor 3/ Nonoffensive
1/ California Air Resources Board Regulations.
2/ Grabner-CA equation (RVPE psi = 0.972 * ptot – 0.71)
3/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt % dicyclopentadiene will
not be accepted for shipment. 4/ In addition to Nustar specifications, product must meet latest revision of ASTM D4814.
Rev. 1
3/13/09
Central West
Product Specifications Page 26 December 1, 2011
SPECIFICATIONS FOR CARB PREMIUM GASOLINE
Grade 36
This product requires the addition of 5.7 vol.% ethanol.
ASTM Origin
Test 1/ Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed
Volatility 2/ D323 12.5 - Jan. 1st
5.99 - Feb. 1st
10.5 - Nov. 1st
12.5 - Dec. 1st
Distillation, degrees F D86-99ae1 Feb 1st
Nov.1st
Dec 1st
T50, max 232 237 237 T90, max 335 335 335
End point, max 437 437 437 Phosphorous, g/gal D3231 0.005
Lead, g/gal D3237 0.030
Research Octane {R} D2699 Report
Motor Octane {M} D2700 Report
(R+M)/2 D4814 90.0 Benzene, vol.% D5580-95 1.22
Aromatic HC, vol.% D5580-00 38.7 Olefins, vol.% D4815-99 0.025
Sulfur, ppm D2622-94 32
D5453-93 Oxygen, wt % D4815-99 0.25
Haze rating 4/ D4176 2 3 Odor 3/ Nonoffensive
1/ California Air Resources Board Regulations.
2/ Grabner-CA equation (RVPE psi = 0.972 * ptot – 0.71)
3/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt % dicyclopentadiene will
not be accepted for shipment.
4/ In addition to Nustar specifications, product must meet latest revision of ASTM D4814.
Rev. 1
3/13/09
SPECIFICATIONS FOR 85 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK
(CBOB)
For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806.
This CBOB may not be combined with any other CBOB except CBOB having the same requirement for oxygenate type and amount.
All parameters must be met after blending with denatured fuel ethanol unless noted.
Requirements for both Segregated and Fungible:
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Note
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 85.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/ 2/ 7/
MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50 7/
DVPE D5191 3/
080, 008 8.0 081, 108 8.8 082, 208 10.0 083, 308 12.5 084, 408 14.5 085, 508 16.0
Fungible only requirements:
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Benzene, vol % D3606 4.9
Gravity, Degrees API D287,D1298,D4052
Color
Report Only 7/
Undyed Doctor test D4952 Negative(sweet) 5/
or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05
Central West
Product Specifications Page 27 December 1, 2011
Central West
Product Specifications Page 28
December 1, 2011
SPECIFICATIONS FOR 85 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK
(CBOB)
Sulfur, ppm D2622 80 8/
NACE Corrosion TM0172 B+(Origin) 7/
Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min
080,081,082 1250 158 150 250 374 430 120
083 1230 140 150 240 365 430 116
084 1220 131 150 235 365 430 107
085 1200 122 150 230 365 430 102
NOTES (Apply to Fungible and Segregated):
Heavy metals are not allowed.
This is a base gasoline, not for sale to the ultimate consumer. Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for
shipment.
The referee method will be based on a gas chromatograph test.
Delivery test results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as
allowed by state or EPA regulations at the point of delivery.
1/ All 08 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending components in
these grades is prohibited.
2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods, ASTM
D1319 and D4815, may be used according to federal and state regulations.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance with the procedures described in 40 CFR, Part 80.
4/ Reserved
5/ Mercaptan sulfur waived if fuel is negative by Doctor Test.
6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method.
7/ Specifications must be met before blending of denatured fuel ethanol.
8/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according to federal
and state regulations.
Rev. 2
03/28/11
Central West
Product Specifications Page 29
December 1, 2011
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Benzene, vol % D3606 4.9
SPECIFICATIONS FOR 86 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK
(CBOB)
For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806. This CBOB may not be combined with any other CBOB except CBOB having the same requirement for oxygenate type and amount.
All parameters must be met after blending with denatured fuel ethanol unless noted.
Requirements for both Segregated and Fungible:
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Note
Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 86.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/ 2/ 7/
MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50 7/
DVPE D5191 3/
080, 008 7.8 081, 108 8.8 082, 208 10.0 083, 308 12.5 084, 408 14.5 085, 508 16.0
Fungible only requirements:
Gravity, Degrees API D287,D1298,D4052
Color
Report Only 7/
Undyed Doctor test D4952 Negative(sweet) 5/
or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05
Central West
Product Specifications December 1, 2011 Page 30
SPECIFICATIONS FOR 86 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK
(CBOB)
Sulfur, ppm D2622 80 8/
NACE Corrosion TM0172 B+(Origin) 7/
Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable)
Grades Index Max Min Max Max Max Min
080,081,082 1250 158 150 250 374 430 120
083 1230 140 150 240 365 430 116
084 1220 131 150 235 365 430 107
085 1200 122 150 230 365 430 102
NOTES (Apply to Fungible and Segregated):
Heavy metals are not allowed.
This is a base gasoline, not for sale to the ultimate consumer.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for
shipment. The referee method will be based on a gas chromatograph test.
Delivery test results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as
allowed by state or EPA regulations at the point of delivery.
1/ All 08 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending components in
these grades is prohibited.
2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods, ASTM
D1319 and D4815, may be used according to federal and state regulations.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance with the
procedures described in 40 CFR, Part 80. 4/ Reserved
5/ Mercaptan sulfur waived if fuel is negative by Doctor Test.
6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method. 7/ Specifications must be met before blending of denatured fuel ethanol.
8/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according to federal
and state regulations.
Rev. 2
03/28/11
Central West
Product Specifications December 1, 2011 Page 31
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Benzene, vol % D3606 4.9
SPECIFICATIONS FOR 87 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK
(CBOB) – GRADE 08
For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806. This CBOB may not be combined with any other CBOB except CBOB having the same requirement for oxygenate type and amount.
All parameters must be met after blending with denatured fuel ethanol unless noted.
Requirements for both Segregated and Fungible:
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Note
Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 87.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/ 2/ 7/
MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50 7/
DVPE D5191 3/
080, 008 8.0 081, 108 8.8 082, 208 10.0 083, 308 12.5 084, 408 14.5 085, 508 16.0
Fungible only requirements:
Gravity, Degrees API D287,D1298,D4052
Color
Report Only 7/
Undyed Doctor test D4952 Negative(sweet) 5/
or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05
Central West
Product Specifications December 1, 2011 Page 32
SPECIFICATIONS FOR 87 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK
(CBOB) – GRADE 08
Sulfur, ppm D2622 80 8/
NACE Corrosion TM0172 B+(Origin) 7/
Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable)
Grades Index Max Min Max Max Max Min
080,081,082 1250 158 150 250 374 430 120
083 1230 140 150 240 365 430 116
084 1220 131 150 235 365 430 107
085 1200 122 150 230 365 430 102
NOTES (Apply to Fungible and Segregated):
Heavy metals are not allowed.
This is a base gasoline, not for sale to the ultimate consumer.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for
shipment. The referee method will be based on a gas chromatograph test.
Delivery test results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as
allowed by state or EPA regulations at the point of delivery.
1/ All 08 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending components in
these grades is prohibited.
2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods, ASTM
D1319 and D4815, may be used according to federal and state regulations.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance with the
procedures described in 40 CFR, Part 80. 4/ Reserved
5/ Mercaptan sulfur waived if fuel is negative by Doctor Test.
6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method. 7/ Specifications must be met before blending of denatured fuel ethanol.
8/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according to federal
and state regulations.
Rev. 2
03/28/2011
December 1, 2011
Central West
Product Specifications Page 33
SPECIFICATIONS FOR PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK
(PBOB) – 90 OCTANE
For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806.
This PBOB may not be combined with any other PBOB except PBOB having the same
requirement for oxygenate type and amount.
All parameters must be met after blending with denatured fuel ethanol unless noted.
Requirements for both Segregated and Fungible:
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 90.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/, 2/, 8/
MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50
DVPE 3/ D5191 220, 022 7.0 221, 122 7.8 222, 222 9.0 223, 322 11.5 224, 422 13.5 225, 522 15.0
This is a base gasoline, not for sale to the ultimate consumer.
Heavy metals are not allowed.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be
accepted for shipment.
The referee method will be based on a gas chromatograph test.
Emissions reductions must be calculated using EPA guidelines.
December 1, 2011
Central West
Product Specifications Page 34
SPECIFICATIONS FOR PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK
(PBOB) – 90 OCTANE Fungible only requirements:
ASTM Origin Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only 7/ Color Undyed Mercaptan Sulfur, wt % 4/ D3227 0.002 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 9/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable) Grades Index Max Min Max Max Max Min 220,221,222 1250 158 170 250 374 430 133 223 1230 140 170 240 365 430 124 224 1220 131 170 235 365 430 116 225 1200 122 170 230 365 430 105
NOTES (Apply to Fungible and Segregated):
1/ All 22 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending
components in these grades is prohibited. 2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods,
ASTM D1319 and D4815, may be used according to federal and state regulations.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance
with the procedures described in 40 CFR, Part 80.
4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according
to federal and state regulations. 6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the referee.
7/ Specifications must be met before blending of denatured fuel ethanol. 8/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending of denatured fuel
ethanol. 9/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max
Rev. 2 03/28/2011
December 1, 2011
Central West
Product Specifications Page 35
ASTM Origin Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only 7/ Color Undyed Mercaptan Sulfur, wt % 4/ D3227 0.002 Hydrogen Sulfide D3227 None
SPECIFICATIONS FOR PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK
(PBOB) – 91 OCTANE
For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806.
This PBOB may not be combined with any other PBOB except PBOB having the same
requirement for oxygenate type and amount.
All parameters must be met after blending with denatured fuel ethanol unless noted.
Requirements for both Segregated and Fungible:
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 91.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/, 2/, 8/
MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50
DVPE 3/ D5191 220, 022 7.0 221, 122 7.8 222, 222 9.0 223, 322 11.5 224, 422 13.5 225, 522 15.0
This is a base gasoline, not for sale to the ultimate consumer.
Heavy metals are not allowed.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene wi ll not be
accepted for shipment.
The referee method will be based on a gas chromatograph test.
Emissions reductions must be calculated using EPA guidelines.
Fungible only requirements:
SPECIFICATIONS FOR PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK
(PBOB) – 91 OCTANE
Copper Corrosion D130 1
Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 9/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable) Grades Index Max Min Max Max Max Min 220,221,222 1250 158 170 250 374 430 133 223 1230 140 170 240 365 430 124 224 1220 131 170 235 365 430 116 225 1200 122 170 230 365 430 105
NOTES (Apply to Fungible and Segregated):
1/ All 22 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending
components in these grades is prohibited. 2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods,
ASTM D1319 and D4815, may be used according to federal and state regulations.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance
with the procedures described in 40 CFR, Part 80. 4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according
to federal and state regulations.
6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the referee.
7/ Specifications must be met before blending of denatured fuel ethanol.
8/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending of denatured fuel
ethanol.
9/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max
Rev. 2 03/28/2011
Central West Product Specifications Page 36 December 1, 2011
Central West
Product Specifications Page 37
December 1, 2011
SPECIFICATIONS FOR PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK
(PBOB) – GRADE 22
For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806.
This PBOB may not be combined with any other PBOB except PBOB having the same
requirement for oxygenate type and amount.
All parameters must be met after blending with denatured fuel ethanol unless noted.
Requirements for both Segregated and Fungible:
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/, 2/, 8/
MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50
DVPE 3/ D5191 220, 022 7.0 221, 122 7.8 222, 222 9.0 223, 322 11.5 224, 422 13.5 225, 522 15.0
This is a base gasoline, not for sale to the ultimate consumer.
Heavy metals are not allowed.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be
accepted for shipment.
The referee method will be based on a gas chromatograph test.
Emissions reductions must be calculated using EPA guidelines.
Fungible only requirements:
ASTM Origin Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only 7/ Color Undyed Mercaptan Sulfur, wt % 4/ D3227 0.002
Central West
Product Specifications Page 38
December 1, 2011
SPECIFICATIONS FOR PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK
(PBOB) – GRADE 22
Hydrogen Sulfide D3227 None
Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 9/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable) Grades Index Max Min Max Max Max Min 220,221,222 1250 158 170 250 374 430 120 223 1230 140 170 240 365 430 116 224 1220 131 170 235 365 430 107 225 1200 122 170 230 365 430 102
NOTES (Apply to Fungible and Segregated):
1/ All 22 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending
components in these grades is prohibited. 2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods,
ASTM D1319 and D4815, may be used according to federal and state regulations.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance
with the procedures described in 40 CFR, Part 80. 4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according to federal and state regulations.
6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the referee.
7/ Specifications must be met before blending of denatured fuel ethanol.
8/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending of denatured fuel
ethanol.
9/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted
seasonally: February 16 – September 30 55 F max
October 1 – February 15 45 F max
Rev. 2 03/28/2011
Central West
Product Specifications Page 39
December 1, 2011
SPECIFICATIONS FOR 85 OCTANE CONVENTIONAL GRADE GASOLINE
(Conventional Gasoline - This product does not meet the requirements for reformulated gasoline and may not be
used in any reformulated gasoline covered area.)
ASTM Origin Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.010 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 85.0 Sulfur, ppm 3/ D2622 80 Oxygenates, wt % D4815 0.33 Haze rating 4/ D4176 2 3 NACE Corrosion TM0172 B+
Odor 5/ Nonoffensive
1/ Refer to Seasonal Gasoline Volatility Schedule.
2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
3/ Gasoline exceeding the origin specification will be accepted from small refineries as defined in 40 CFR
part 80 of the EPA regulations.
4/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures,
adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
5/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt % dicyclopentadiene will
not be accepted for shipment.
Rev. 1
10/21/10
Central West
Product Specifications Page 40
December 1, 2011
SPECIFICATIONS FOR 86 OCTANE CONVENTIONAL GRADE GASOLINE
(Conventional Gasoline - This product does not meet the requirements for reformulated gasoline
and may not be used in any reformulated gasoline covered area.)
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.003 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 86.0 Sulfur, ppm 3/ D2622 80 Oxygenates, wt % D4815 0.33 Haze rating 4/ D4176 2 3
NACE Corrosion TM0172 B+ Odor 5/ Nonoffensive
1/ Refer to Seasonal Gasoline Volatility Schedule.
2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
3/ Gasoline exceeding the origin specification will be accepted from small refineries as
defined in 40 CFR part 80 of the EPA regulations.
4/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
Central West
Product Specifications Page 41 December 1, 2011
SPECIFICATIONS FOR 86 OCTANE CONVENTIONAL GRADE GASOLINE
February 16 – September 30 55 F max
October 1 – February 15 45 F max
5/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt %
dicyclopentadiene will not be accepted for shipment.
Rev. 1
10/21/10
Central West
Product Specifications Page 42
December 1, 2011
SPECIFICATIONS FOR 87 OCTANE INDEX CONVENTIONAL GASOLINE
GRADE 03
This product does not meet requirements for reformulated gasoline, and may not be used in any reformulated
gasoline covered area.
Requirements for both Segregated and Fungible:
ASTM
Test
Origin
Shipments
Deliveries Specification Points Research Octane {R}
Motor Octane {M}
Method D2699
D2700
Minimum Report
82.0
Maximum (At Terminals) Note
(R+M)/2 D4814 87.0
Oxygen Content, wt %
D4815,
D5599 , GC-OFID
0.1
1/
MTBE, vol.%
D4815,
D5599, GC-OFID
0.25
0.50
2/
DVPE
030, 003
D5191 7.0
3/
031, 103 7.8 032, 203 9.0 033, 303 11.5 034, 403 13.5 035, 503 15.0
This is a base gasoline, not for sale to the ultimate consumer.
Heavy metals are not allowed.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for
shipment.
The referee method will be based on a gas chromatograph test.
Delivery of any 03 grade to final destination in Virginia, and Maryland may contain MTBE.
Fungible only requirements:
Central West
Product Specifications Page 43
December 1, 2011
SPECIFICATIONS FOR 87 OCTANE INDEX CONVENTIONAL GASOLINE
GRADE 03
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Note
Gravity, Degrees API D287, D1298,D4052 Report Only Color Undyed Doctor test D4952 Negative(sweet) 4/
or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm D2622 80 5/
NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min
030,031,032 1250 158 170 250 374 430 133
033 1230 140 170 240 365 430 124
034 1220 131 170 235 365 430 116
035 1200 122 170 230 365 430 105
NOTES (Apply to Fungible and Segregated):
1/ Non-oxygenated is defined as having no more than 0.1 wt.% oxygen. The use of oxygenated and/or non-
hydrocarbon blending components in these grades is prohibited.
2/ Delivery of any 03 grade to final destination s in Virginia, and Maryland may contain MTBE.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in
accordance with the procedures described in 40 CFR, Part 80.
4/ Mercaptan sulfur waived if the fuel is negative by the Doctor Test.
5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used
according to federal and state regulations.
6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the referee.
Rev. 2
03/28/2011
Central West
Product Specifications Page 44
December 1, 2011
SPECIFICATIONS FOR 90 OCTANE CONVENTIONAL GRADE GASOLINE
(Conventional Gasoline - This product does not meet the requirements for reformulated gasoline
and may not be used in any reformulated gasoline covered area.)
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.003 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 90.0 Sulfur, ppm 3/ D2622 80 Oxygenates, wt % D4815 0.33 Haze rating 4/ D4176 2 3
NACE Corrosion TM0172 B+ Odor 5/ Nonoffensive
1/ Refer to Seasonal Gasoline Volatility Schedule.
2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
3/ Gasoline exceeding the origin specification will be accepted from small refineries as
defined in 40 CFR part 80 of the EPA regulations.
4/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
Central West
Product Specifications Page 45
December 1, 2011
SPECIFICATIONS FOR 90 OCTANE CONVENTIONAL GRADE GASOLINE
5/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt %
dicyclopentadiene will not be accepted for shipment.
Rev. 1
10/21/10
Central West
Product Specifications Page 46
December 1, 2011
SPECIFICATIONS FOR 91 OCTANE CONVENTIONAL GRADE GASOLINE
(Conventional Gasoline - This product does not meet the requirements for reformulated gasoline
and may not be used in any reformulated gasoline covered area.)
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.003 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 91.0 Sulfur, ppm 3/ D2622 80 Oxygenates, wt % D4815 0.33 Haze rating 4/ D4176 2 3
NACE Corrosion TM0172 B+ Odor 5/ Nonoffensive
1/ Refer to Seasonal Gasoline Volatility Schedule.
2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
3/ Gasoline exceeding the origin specification will be accepted from small refineries as
defined in 40 CFR part 80 of the EPA regulations.
4/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
Central West
Product Specifications Page 47
December 1, 2011
SPECIFICATIONS FOR 91 OCTANE CONVENTIONAL GRADE GASOLINE
February 16 – September 30 55 F max
October 1 – February 15 45 F max
5/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt %
dicyclopentadiene will not be accepted for shipment.
Rev. 1
10/21/10
Central West
Product Specifications Page 48
December 1, 2011
SPECIFICATIONS FOR 93 OCTANE INDEX CONVENTIONAL GASOLINE
GRADE 01
This product does not meet requirements for reformulated gasoline, and may not be used in any
reformulated gasoline covered area.
Requirements for both Segregated and Fungible:
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/
MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50 2/
DVPE 3/ D5191 010, 001 7.0 011, 101 7.8 012, 201 9.0 013, 301 11.5 014, 401 13.5 015, 501 15.0
This is a base gasoline, not for sale to the ultimate consumer.
Heavy metals are not allowed.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be
accepted for shipment.
The referee method will be based on a gas chromatograph test.
Delivery of any 01 grade to final destination in North Carolina, Virginia, and Maryland
may contain MTBE.
Fungible only requirements:
ASTM Origin Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed
SPECIFICATIONS FOR 93 OCTANE INDEX CONVENTIONAL GASOLINE
GRADE 01
Mercaptan Sulfur, wt % 4/ D3227 0.002
Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 7/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min 011,012 1250 158 170 250 374 430 133 013 1230 140 170 240 365 430 124 014 1220 131 170 235 365 430 116 015 1200 122 170 230 365 430 105
NOTES (Apply to Fungible and Segregated):
1/ Non-oxygenated is defined as having no more than 0.1 wt.% oxygen. The use of oxygenated and/or non-
hydrocarbon blending components in these grades is prohibited.
2/ Delivery of any 01 grade to final destination s in North Carolina, Virginia, and Maryland may contain
MTBE.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in
accordance with the procedures described in 40 CFR, Part 80.
4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.
5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used
according to federal and state regulations.
6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the
referee.
7/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures,
adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
Rev. 2
03/28/2011
Central West Product Specifications Page 49 December 1, 2011
(Ramsbottom) - Percent D524 0.35
Cloud Point, F D2500, D5771 2/
D5772, D5773 Pour Point, F D97, D5949 2/
D5950, D5985 Viscosity, cSt @104 F D445 1.9 4.1 Haze Rating 3/ D4176 2 3 Ash, wt % D482 0.01 Sulfur, ppm 4/ D2622 *10 15
NACE Corrosion TM0172 B+ Aromatics (Volume %) D1319 31.7 Or Aromatics by Cetane Index D976 40
SPECIFICATION FOR FUNGIBLE ULTRA LOW SULFUR FUEL DIESEL
GRADE 37
ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be Gravity, Degrees A.P.I. D287 30
Color D1500 2.5 3.0
Color visual Undyed
Distillation, D86
50% Recovered, F Report
90% Recovered, F 540 640
OR
Simulated distillation D2887
50% Recovered, F Report
90% Recovered, F 572 673
Corrosion, Copper Strip @122 F D130 1
Cetane Number D613 40 1/
Flash, F D93 130
Thermal Stability, 90 minutes
(1) 150C Pad rating,
DuPont scale 7
OR (2) Oxidation, mg/100ml D2274 2.5
Carbon Residue on 10% Bottoms
Central West Product Specifications Page 50 December 1, 2011
Central West Product Specifications Page 51
December 1, 2011
SPECIFICATION FOR FUNGIBLE ULTRA LOW SULFUR FUEL DIESEL
GRADE 37
BS&W, vol.% D2709 <0.05
Conductivity, pS/m @ 70 F D2624 250
1/ Where cetane number by test method D613 is not available, test method D4737B can be
used as an approximation.
2/ This schedule denotes the fluidity of the distillate at the time and place of origin.
Cloud point – August 1st
through March 14th
Maximum:
+15 F
Cloud point – March 15th
through July 31st
Maximum:
+20 F
Pour point – August 1st
through March 14th
Maximum:
0 F
Pour point – March 15th
through July 31st
Maximum:
+10 F
The referee method will be Cloud point D2500 and Pour point D97.
3/ The finished product shall be visually free of undissolved water, sediment, and suspended
matter in proffered tankage and at the point of delivery. Compliance with this
workmanship clause will be determined by ASTM D4176, Procedure 2 at 77 F or at
actual conditions present at the point and time of sampling, whichever is lower.
4/ Origin laboratory certifying sulfur content must qualify the test method used per EPA
Performance Based Testing Criteria (see CFR 80.584). The referee method will be
ASTM D5453. *Sulfur limit, 12 ppm for interconnecting pipelines.
Rev. 1
3/13/09
Central West Product Specifications Page 52
December 1, 2011
(Ramsbottom) - Percent D524
Cloud Point, F D2500, D5771 0.35
4/
D5772, D5773 Pour Point, F D97, D5949 4/
D5950, D5985 Viscosity, csT @104 F D445 1.9 3.4 Haze Rating 5/ D4176 2 3 Ash, wt % D482 0.01 Sulfur, ppm 6/ D2622, D5453 420 500
SPECIFICATION FOR LOW SULFUR HIGHWAY DIESEL FUEL
GRADE 06
ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be
Gravity, Degrees A.P.I. D287, D1298 30
D4052
Color ASTM D1500, D6045 2.5 3.0
Color Visual Undyed
Distillation, D86
50% Recovered, F Report 1/
90% Recovered, F 540 640
End Point, F 690
OR
Simulated distillation D2887 1/
50% Recovered, F Report
90% Recovered, F 572 673
End Point, F 723
Corrosion, Copper Strip @122 F D130 1
Cetane Number D613 40 2/
Aromatics (Volume %) D1319 31.7
Or Aromatics by Cetane Index D976 40
Flash, F D93 130
Thermal stability, 90 minutes
150 C Pad rating,
DuPont scale 7
or
Oxidation stability,mg/100ml D2274 2.5
Carbon Residue on 10% Bottoms
Central West
Product Specifications Page 53
December 1, 2011
SPECIFICATION FOR LOW SULFUR HIGHWAY DIESEL FUEL
GRADE 06
D7039
NACE Corrosion TM0172 B+
BS&W, vol.% D2709 <0.05
Conductivity, pS/m @ 70 F D2624 250
1/ Either physical or simulated distillation can be used. The referee test method will be
ASTM D86.
2/ Where cetane number by test method D613 is not available, test method D4737B can be
used as an approximation.
3/ The Potential Gum will be determined by ASTM Method D381 Modified (Steam Jet
Evaporated @ 485 F) after a 16 hour induction period by ASTM Method D525
Modified.
4/ This schedule denotes the fluidity of the distillate at the time and place of origin.
Cloud Point – August 1st
through March 14th
Maximum:
+15 F
Cloud Point – March 15th
through July 31st
Maximum:
+20 F
Pour Point – August 1st
through March 14th
Maximum:
0 F
Pour Point – March 15th
through July 31st
Maximum:
+10 F
The referee method will be Cloud point D2500 and Pour point D97.
5/ The finished product shall be visually free of undissolved water, sediment, and suspended
matter in proffered tankage and at the point of delivery. Compliance with this
workmanship clause will be determined by ASTM D4176, Procedure 2 at 77 F or at
actual conditions present at the point and time of sampling, whichever is lower.
6/ Origin laboratory certifying sulfur content must qualify the test method used per EPA
Performance Based Testing Criteria (see CFR 80.584). The referee test method will be
ASTM D5453.
Rev. 1
3/13/09
Central West
Product Specifications Page 54
December 1, 2011
SPECIFICATION FOR SEGREGATED DISTILLATE BLENDSTOCK
ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be
Gravity, Degrees A.P.I. D287 37 51
Flash, F
D56, D3828
100
Sulfur, ppm
D2622, D5453
D7039, D4294
3000
1/
NACE Corrosion
TM0172
B+ (origin)
Conductivity, pS/m @ 70 F
D2624
Report
1/ Origin laboratory certifying sulfur content can qualify the test method used per EPA
Performance Based Testing Criteria (see CFR 80.584). The referee test method will be
ASTM D545.
Product shall be clear and bright and free of suspended matter.
Rev. 1
3/13/09
Central West
Product Specifications Page 55 December 1, 2011
SPECIFICATION FOR SEGREGATED DISTILLATE BLENDSTOCK
GRADE 43
ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be
Gravity, Degrees A.P.I. D287, D1298 25 42
D4052
Flash, F D93 100
Sulfur, ppm 1/ D2622, D5453 10,000
D7039
NACE Corrosion TM0172 B+
Conductivity, pS/m @ 70 F D2624 250
Dye Requirement:
Origin: This product must exhibit visual evidence that red dye is present. The maximum allowable
concentration, or spectral equivalence, is 0.75 pounds of Solid Red #26 per 1,000 barrels. This product does not meet IRS excise tax requirements for dye.
Delivery: This product will be dyed by NuStar to meet a minimum dye concentration, or spectral
equivalence, of 3.9 pounds of Solid Red #26 per 1,000 barrels.
A waiver from Quality Assurance for the dye requirement will be given if the source and ultimate
destination are refineries.
This schedule denotes the fluidity of the distillate at the time and place of origin.
Cloud Point – August 1st
through March 14th
Cloud Point – March 15th
through July 31st
Maximum:
Maximum:
+15 F +20 F
Pour Point – August 1st
through March 14th
Maximum:
0 F Pour Point – March 15
th through July 31
st Maximum: +10 F
The referee method will be Cloud Point D2500 and Pour Point D97.
1/ Origin laboratory certifying sulfur content can qualify the test method used per EPA Performance
Based Testing Criteria (see CFR 80.584). The referee method will be ASTM D5453.
Rev. 2 03/30/2011
Central West
Product Specifications Page 56 December 1, 2011
SPECIFICATION FOR L GRADE PROPANE
Grade 12
ASTM Shipments Deliveries
Test (At Origin) (From Terminals) Specification Points Methods Minimum Maximum 1/ Composition
Chromatograph analysis D2163
Percent by liquid volume: Propane 90 Propylene 5.0 Butanes and heavier 2.5 Pentanes and heavier None
Specific gravity, at 60/60 F D1657 0.500 0.510 Vapor pressure, psig at 100 F D1267 175 208 D2598, D6897 Weathering, 95% evaporated D1837 -37 Temp., F (corrected) Residues, D2158 Nonvolatile residue at 100 F, ml 0.05 Oil, no oil stain observation, ml 0.3 Sulfur, D2784,D6667 grains per hundred cubic feet 10 (or 123 ppmw) Corrosion, copper strip at 100 F D1838 No. 1 Dryness Valve freeze, seconds D2713 60
1/ Same as shipment specifications except for normal testing and handling tolerances.
Additives: L-grade propane shipments at origin shall be unstenched and contain no additives. Unless
otherwise notified in writing by shipper, L-grade propane deliveries will be odorized at the rate of 1 ½
pounds Ethyl Mercaptan/10,000 gallons.
Method of Inspection: Inspection shall be in accordance with MSTI, “Instructions Governing the
Measurement, Sampling and Testing of Products for Acceptance and Delivery,” currently in effect on
inspection date.
Rev.1
3/13/09
Central West
Product Specifications Page 57 December 1, 2011
SPECIFICATIONS FOR 93 OCTANE INDEX REFORMULATED GASOLINE
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed DVPE 1/ D5191
D3,3D,6D (Non-VOC controlled) 11.5 D4,4D,7D (Non-VOC controlled) 13.5 D5,5D,8D (Non-VOC controlled) 15.0 D1,1D,D2,2D (VOC controlled) Report 1/
Mercaptan Sulfur, wt % 2/ D3227 0.002 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.004 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Sulfur, ppm 3/ D2622 80 Oxygen Content, wt % D5599 1.7 2.7 4/, 5/
Haze rating 6/ D4176 2 3
NACE Corrosion TM0172 B+ Benzene, vol % D3606 1.30 Aromatics, vol % D5599 50 5/
E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 25 Emissions Performance Reductions, %
Region 1 (A1, 1A) -27 (-29 during cycles 14-21) -25
Region 2 (A2, 2A) -25.4 (-27.4 during cycles 14-21) -23.4
Odor 7/ Nonoffensive Volatility: Driveability Index D4814 See chart
SPECIFICATIONS FOR 93 OCTANE INDEX REFORMULATED GASOLINE
Distillation, F @ % Evap. D86
Vapor/Liquid Ratio (V/L), F @20 8/
D2533, D5188
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min
D1,D2 1250 158 170 250 374 430 133
D3,6D 1230 140 170 240 365 430 124
D4,7D 1220 131 170 235 365 430 116
D5,8D 1200 122 170 230 365 430 105
This is a base gasoline, not for sale to the ultimate consumer.
1/ For products blended to meet EPA or state imposed summer VOC requirements, tests
must be performed in accordance with the procedures described in 40 CFR, Part 80.
2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
3/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and
D7039, may be used according to federal and state regulations.
4/ Non-hydrocarbon blending components are to be reported on the certified laboratory
report by type and percent (by volume). This product is required to contain aliphatic
ether(s). The use of any other non-hydrocarbons, such as alcohols, as blending
components is prohibited.
5/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics
and oxygenates test methods, ASTM D1319 and D4815, may be used according to
federal and state regulations.
6/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
7/ Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt %
dicyclopentadiene will not be accepted for shipment.
8/ Computer, Linear and Nomogram methods may be used to determine V/L value. D2533
will be the referee.
Rev. 1
3/13/09
Central West Product Specifications Page 58 December 1, 2011
Central West
Product Specifications Page 59 December 1, 2011
Region 1 (E1, 1E) -27 (-28 during cycles 14-21) -25
Region 2 (E2, 2E) -25.4 (-26.4 during cycles 14-21) -23.4
SPECIFICATIONS FOR 87 OCTANE INDEX REFORMULATED GASOLINE
BLENDSTOCK (RBOB)
For Blending With 5.7% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only 1/
Color Undyed RVP 2/ D5191
E3, 3E (Non-VOC controlled) 11.5 E4, 4E (Non-VOC controlled) 13.5 E5, 5E (Non-VOC controlled) 15.0 E1,1E,E2,2E (VOC controlled) Report 2/, 6/
Mercaptan Sulfur, wt % 3/ D3227 0.002 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.004 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 87.0 Sulfur, ppm 4/ D2622 80 Oxygen Content, wt % D5599 5/, 6/, 10/
Haze rating 7/ D4176 2 3
NACE Corrosion TM0172 B+ Benzene, vol % D3606 1.30 Aromatics, vol % D5599 50 6/
E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 25 Emissions Performance Reductions, % 11/
December 1, 2011
Central West
Product Specifications Page 60
SPECIFICATIONS FOR 87 OCTANE INDEX REFORMULATED GASOLINE
BLENDSTOCK (RBOB)
Odor 8/ Nonoffensive
Volatility:
Driveability Index D4814 See chart
Distillation, F @ % Evap. D86
Vapor/Liquid Ratio (V/L), F @20 9/
D2533, D5188
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min
E1,E2 1250 158 170 250 374 430 133
E3 1230 140 170 240 365 430 124
E4 1220 131 170 235 365 430 116
E5 1200 122 170 230 365 430 105
This is a base gasoline, not for sale to the ultimate consumer.
1/ Specifications must be met before blending of denatured fuel ethanol.
2/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be
performed in accordance with the procedures described in 40 CFR, Part 80.
3/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
4/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039,
may be used according to federal and state regulations.
5/ All E grades may not contain oxygenates, such as ethers and alcohols. The use of non-
hydrocarbon blending components is prohibited. Origin maximum MTBE 0.25 vol.%. Delivery
maximum 0.50 vol.%.
6/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and
oxygenates test methods, ASTM D1319 and D4815, may be used according to federal and state
regulations.
7/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
8/ Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for shipment.
9/ Computer, Linear and Nomogram methods may be used to determine V/L value. D2533 will be
the referee. 10/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending
with denatured fuel ethanol. 11/ Emissions reductions must be calculated using EPA guidelines.
Revision date: 3/13/09
December 1, 2011
Central West
Product Specifications Page 61
Doctor test D4952 Negative(sweet) 5/
or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
SPECIFICATIONS FOR 87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK
(RBOB)
GRADE 21
For Blending With 10% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806
All Grade 21 Requirements (Segregated and Fungible)
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Note
Benzene, vol % D3606 1.30 Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 87.0 Oxygen Content, wt % D5599,GC-OFID(See Note) 1/2/7/8/
Aromatics, vol % D5769,D5599,GC-OFID(See Note) 50 2/ E200, vol % D86 30 70
E300, vol % D86 70 100
Olefins, vol % D1319, D6550 25
Sulfur, ppm D2622 80 9/
Non-VOC Controlled Requirements
DVPE D5191 3/
213, 321 (Non-VOC controlled) 11.5
214, 421 (Non-VOC controlled) 13.5
215, 521 (Non-VOC controlled) 15.0 VOC Controlled Requirements DVPE D5191 3/
211,121,212,221 (VOC controlled) Report 2/ Emissions Performance Reductions, % 4/
Region 1 (211, 121) -27 -25 Region 2 (212, 221) -25.4 -23.4
Fungible Only Requirements: Color Undyed
December 1, 2011
Central West
Product Specifications Page 62
SPECIFICATIONS FOR 87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK
(RBOB)
GRADE 21
Gravity API @ 60F D287,D1298,D4052 Report 7/
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.004 0.005
Lead, g/gal D3237 0.010 0.05
NACE Corrosion TM0172 B+ 7/
Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min
211,212 1250 158 170 250 374 430 133
213 1230 140 170 240 365 430 124
214 1220 131 150 235 365 430 116
215 1200 122 150 230 365 430 105
This is a base gasoline, not for sale to the ultimate consumer.
Heavy metals are not allowed to be present.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.
Any gasoline containing more than 0.50 wt.% of dicyclopentadiene will not be accepted for shipment.
The referee method will be based on a gas chromatograph test.
Delivery test results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as allowed by
state or EPA regulations at the point of delivery.
1/ All 21 grades may not contain oxygenates, such as ethers and alcohols. The use of non -hydrocarbon blending
components is prohibited. Origin maximum MTBE 0.25 vol.%. Delivery maximum 0.50 vol.%.
2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and oxygenates test methods,
ASTM D1319 and D4815, may be used according to federal and state regulations.
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in
accordance with the procedures described in 40 CFR, Part 80. 4/ Emissions reductions must be calculated using EPA guidelines.
5/ Mercaptan Sulfur waived if fuel is negative by Doctor test.
6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method.
7/ Specifications must be met before blending of denatured fuel ethanol.
8/ Oxygen content must meet a minimum of 1.7wt. % and a maximum of 4.0 wt. % after blending of denatured fuel
ethanol.
9/ Refer to 40 CFR Part 80.195 (d)(2). Alternative sulfur test methods, ASTM D5453 and D7039, may be used
according to federal and state regulations.
Rev. 2
03/28/2011
SPECIFICATIONS FOR AR GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB)
For Blending With 10.0% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ DVPE 2/ D5191 7.20 Mercaptan Sulfur, wt % 3/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.003 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 8/ D4814 91.3 (R+M)/2 (After blending) D4814 93.0 Benzene, wt. % D3606 1.3 Aromatics (vol %) 4/ 50 Olefins (vol %) D1319 25 Sulfur, ppm D2622 80 Oxygen Content wt% 5/ D5599 1.5 4.0 Oxygenates, wt % 8/ D4815 0.33 E200 (vol%) D86 30 70 E300(vol%) D86 70 100 Emission Performance Reduction (%) 27.0 Haze rating 6/, 8/ D4176 2 3
NACE Corrosion TM0172 B+ Odor 7/, 8/ Nonoffensive
Central West Product Specifications Page 63 December 1, 2011
SPECIFICATIONS FOR AR GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB)
1/ Refer to Seasonal Gasoline Volatility Schedule.
2/ For products blended to meet EPA or state imposed summer VOC requirements, test
must be performed for RVP in accordance with procedure described in 40 CFR, PART
80, Appendix E, Method 3.
3/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
4/ Refer to test methods in 40 CFR Chapter 1, Part 80.46.
5/ Oxygen content must meet a minimum of 1.5 wt. % and a maximum of 4.0 wt. % after
blending of denatured fuel ethanol.
6/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
7/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt %
dicyclopentadiene will not be accepted for shipment.
8/ Specfications must be met before blending of denatured fuel ethanol
**NOTE: This RBOB may not be combined with any other RBOB except RBOB having
the same requirement for oxygenate type and amount. “Base Gasoline” Not for sale to the
ultimate consumer.
**NOTE: Heavy metals are not allowed to be present.
**NOTE: All parameters must be met after blending with denatured fuel ethanol unless noted.
Rev. 1
3/13/09
Central West Product Specifications Page 64 December 1, 2011
SPECIFICATIONS FOR NR GRADE GASOLINE BLENDSTOCK (RBOB)
Grade 21 For Blending With 10.0% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ DVPE 2/ D5191 7.20 Mercaptan Sulfur, wt % 3/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.003 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 80.0 (R+M)/2 8/ D4814 83.7 (R+M)/2 (After blending) D4814 87.0 Benzene, wt. % D3606 1.3 Aromatics (vol %) 4/ 50 Olefins (vol %) D1319 25 Sulfur, ppm D2622 80 Oxygen Content wt% 5/ D5599 1.5 4.0 Oxygenates, wt % 8/ D4815 0.33 E200 (vol%) D86 30 70 E300(vol%) D86 70 100 Emission Performance Reduction (%) 27.0 Haze rating 6/, 8/ D4176 2 3
NACE Corrosion TM0172 B+ Odor 7/, 8/ Nonoffensive
Central West Product Specifications Page 65 December 1, 2011
SPECIFICATIONS FOR NR GRADE GASOLINE BLENDSTOCK (RBOB)
Grade 21 1/ Refer to Seasonal Gasoline Volatility Schedule.
2/ For products blended to meet EPA or state imposed summer VOC requirements, test
must be performed for RVP in accordance with procedure described in 40 CFR, PART
80, Appendix E, Method 3.
3/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
4/ Refer to test methods in 40 CFR Chapter 1, Part 80.46.
5/ Oxygen content must meet a minimum of 1.5 wt. % and a maximum of 4.0 wt. % after
blending of denatured fuel ethanol.
6/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
7/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt %
dicyclopentadiene will not be accepted for shipment.
8/ Specfications must be met before blending of denatured fuel ethanol
**NOTE: This RBOB may not be combined with any other RBOB except RBOB having
the same requirement for oxygenate type and amount. “Base Gasoline” Not for sale to the
ultimate consumer.
**NOTE: Heavy metals are not allowed to be present.
**NOTE: All parameters must be met after blending with denatured fuel ethanol unless noted.
Rev. 1
3/13/09
Central West Product Specifications Page 66 December 1, 2011
Central West
Product Specifications Page 67
December 1, 2011
SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK
(RBOB)
For Blending With 5.7% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806
ASTM Origin
Test Shipments Deliveries
Specification Points Method Minimum Maximum (At Terminals)
Gravity, Degrees API D287 Report Only 1/
Color Undyed DVPE 2/ D5191
G3, 3G (Non-VOC controlled) 11.5 G4, 4G(Non-VOC controlled) 13.5 G5, 5G (Non-VOC controlled) 15.0 G1,1G,G2,2G (VOC controlled) Report 6/
Mercaptan Sulfur, wt % 3/ D3227 0.002 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5
Oxidation Stability, min. D525 240 180
Phosphorous, g/gal D3231 0.004 0.005
Lead, g/gal D3237 0.010 0.05
Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Sulfur, ppm 4/ D2622 80 Oxygen Content, wt % D5599 5/, 6/, 10/
Haze rating 7/ D4176 2 3
NACE Corrosion TM0172 B+ Benzene, vol % D3606 1.30 Aromatics, vol % D5599 50 6/
E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 25 Emissions Performance Reductions, % 11/
Region 1 (G1, 1G) -27 (-28 during cycles 14-21) -25
Region 2 (G2, 2G) -25.4 (-26.4 during cycles 14-21) -23.4
Odor 8/ Nonoffensive Volatility: Driveability Index D4814 See chart
Central West
Product Specifications Page 68
December 1, 2011
SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK
(RBOB)
Distillation, F @ % Evap. D86
Vapor/Liquid Ratio (V/L), F @20 9/
D2533, D5188
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min
G1,G2 1250 158 170 250 374 430 133
G3 1230 140 170 240 365 430 124
G4 1220 131 150 235 365 430 116
G5 1200 122 150 230 365 430 105
This is a base gasoline, not for sale to the ultimate consumer.
1/ Specifications must be met before blending of denatured fuel ethanol.
2/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be
performed in accordance with the procedures described in 40 CFR, Part 80.
3/ Mercaptan Sulfur determination is waived if the result of the Doctor Test
ASTM D4952 is negative.
4/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039,
may be used according to federal and state regulations.
5/ All E grades may not contain oxygenates, such as ethers and alcohols. The use of non-
hydrocarbon blending components is prohibited. Origin maximum MTBE 0.25 vol.%. Delivery
maximum 0.50 vol.%.
6/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and
oxygenates test methods, ASTM D1319 and D4815, may be used according to federal and state
regulations.
7/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following
temperatures, adjusted seasonally:
February 16 – September 30 55 F max
October 1 – February 15 45 F max
8/ Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for shipment.
9/ Computer, Linear and Nomogram methods may be used to determine V/L value. D2533 will be
the referee. 10/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending
with denatured fuel ethanol. 11/ Emissions reductions must be calculated using EPA guidelines.
Rev.1, 3/13/09
Central West
Product Specifications Page 69 December 1, 2011
ASTM Origin
Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Note
Benzene, vol % D3606 1.30 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Oxygen Content, wt % D5599,GC-OFID(See Note) 1/2/7/8/
Aromatics, vol % D5769,D5599,GC-OFID(SeeNote) 50 2/ E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 ,D6550 25 Sulfur, ppm D2622 80 9/
DVPE D5191 3/ 223, 322 (Non-VOC controlled) 11.5 224, 422 (Non-VOC controlled) 13.5 225, 522 (Non-VOC controlled) 15.0 221,122,222,222 (VOC controlled) Report 2/
Emissions Performance Reductions, % 4/
Region 1 (221, 122) -27 -25 Region 2 (222, 222) -25.4 -23.4
SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)
– GRADE 22
For Blending With 10% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806
This RBOB may not be combined with any other RBOB except RBOB having the same
requirement for oxygenate type and amount.
All parameters must be met after blending with denatured fuel ethanol unless noted.
All Grade 22 Requirements (Segregated and Fungible):
Central West
Product Specifications December 1, 2011 Page 70
SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)
– GRADE 22
Fungible Only Requirements:
ASTM
Test
Origin
Shipments
Deliveries
Specification Points
Color
Method Minimum Maximum
Undyed
(At Terminals) Note
Copper Corrosion D130 1 Silver Corrosion D4814
Doctor test D4952 1
Negative(sweet)
5/
or
Mercaptan Sulfur, wt % D3227
0.002
Gum, Existent, mg/100ml D381
Gravity, Degrees API D287
Oxidation Stability, min. D525
240
4
Report Only
5
180
7/
Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237
NACE Corrosion TM0172
B+
0.010 0.05 7/
Volatility:
Driveability Index D4814
See chart
Distillation, F @ % Evap. D86
Vapor/Liquid Ratio (V/L), F @20 D5188 See chart
See chart
6/
Driveability 10 vol% 50 vol% 90vol% EndPt V/L
Grades Index Max Min Max Max Max Min
221,222 1250 158 170 250 374 430 133
223 1230 140 170 240 365 430 124
224 1220 131 150 235 365 430 116
225 1200 122 150 230 365 430 105
Heavy metals are not allowed to be present.
This is a base gasoline, not for sale to the ultimate consumer.
Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shi pment.
Any gasoline containing more than 0.50 wt. % of dicyclopentadiene will not be accepted for shipment.
The referee method will be based on a gas chromatograph test.
Delivery results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as allowed by state or
EPA regulations at the point of delivery.
1/ All 21 grades may not contain oxygenates, such as ethers and alcohols. The use of non -hydrocarbon blending
components is prohibited. Origin maximum MTBE 0.25 vol. %. Delivery maximum 0.50 vol.%.
2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and oxygenates test methods,
ASTM D1319 and D4815, may be used according to federal and state regulations.
Central West
Product Specifications December 1, 2011 Page 71
SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)
– GRADE 22
3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in
accordance with the procedures described in 40 CFR, Part 80. 4/ Emissions reductions must be calculated using EPA guidelines.
5/ Mercaptan Sulfur waived if fuel is negative by Doctor test.
6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method.
7/ Specifications must be met before blending of denatured fuel ethanol.
8/ Oxygen content must meet a minimum of 1.7 wt. % and a maximum of 4.0 wt.% after blending with denatured fuel
ethanol.
9/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used
according to federal and state regulations.
Rev. 2
03/29/2011
SPECIFICATION FOR LIGHT NAPHTHA
ASTM Shipments Deliveries
Test (At Origin) (At Terminals)
Specification Points Methods Minimum Maximum May Be Specific Gravity D1298 0.680 0.850
Color D1500 5
Reid Vapor Pressure, psi D5191 12.5
Distillation, D86 IBP 60
Water and Sediment D1786 2.0
Product shall be clear and bright and free of suspended matter.
Rev. 1
11/01/10
Central West
Product Specifications Page 72 December 1, 2011
Gasoline, Fuel Oil and Diesel Fuel Additive Specifications
(From origin or interconnecting pipeline.)
The following additive specifications apply to all grades except aviation
products, LPG’s, and Natural Gasoline.
Gasoline Additives
Gum Inhibitors and Metal Deactivators
Gasoline shipments may, but are not required to, contain any of the following gum
inhibitors and/or metal deactivators:
N, N’di-secondary butyl ortho-phenylenediamine
N, N’di-secondary butyl para-phenlyenediamine
N, N’disalicylidene-1, 2 propanediamine
N, N’di(1-ethyl-3-methylpentyl)-para-phenylenediamine
N, N’di-isopropyl-para-phenylenediamine
N,n’bis-(1, 4-demethylpentyl)-p-phenylenediamine n-butyl-para-aminophenol
2-6-di-tert-butylphenol
2, 4,6-tri-tert-butylphenol
Ortho-tert-butylphenol
UOP12P UOP12S UOP17P
UOP3455 UOP5S Octel AO-31
Octel AO-33 Octel AO-35 Octel AO-36
Ethyl 733 HiTech 4776 HiTech 4720
HiTech4740 Tolad 3905 Tolad 3910
Specaid 8Q202 Naco 88BU-118 IPC 4650
Pitt-Concol M-56 IPC 4695 Unichem 7529
IPC 4690
Corrosion Inhibitors - Products requiring compliance with NACE standard TM0172 may
contain any of the following corrosion inhibitors:
Nalco 5403 Welchem 91120 Nalco 5405
Welchem 91121 Nalco Visco 3554 Specaid8Q103
Apollo PRI-19 Lubrizol 541 Baypros 853
UOP Unicor Octel DCI-4A Unichem 7504
UOP UnicorPL Octel DCI-6A UOP Unicor J
Tolad 245 Hitec E-534 Tolad 249
Central West
Product Specifications Page 73 December 1, 2011
Hitech 580 IPC 4410 Unichem 7501
Tolad 9719 Tolad 9715
Gasoline, Fuel Oil and Diesel Fuel Additive Specifications Fuel Oil and Diesel Fuel additives
Stability Fuel oil and/or diesel fuel shipments may contain one or more of
the following stability additives as required to achieve compliance
with the stability characteristics outlined in the applicable grade
specification.
Octel FOA-3 Chemtec 7220 Octel FOA-11
UOP Polyflo-121 Nalco 5303 Nalco 5301
UOP Polyflo-122 Tretolite Tolad 260 Specaid8Q401
UOP Polyflo-128 Petrolite T-9022 Specaid8Q403
UOP Polyflo-195 Unichem 7530 Specaid8Q72
Tolad 9076
Pour depressants Fuel oil and/or diesel fuel shipments requiring additives to achieve
compliance with low temperature properties may, but are not
required to, contain one or more of the following pour point
depressant additives:
Hitec 4518 Tolad 35 Hitec 4541
Tolad 345 Paradyne 25 Nalco 5375
Unichem 8094 Exxon ECA 7305 Tolad 3005
Octel PDD-7450 UOP Polyflo 6000 Betz 8Q12
Betz Specaid 8Q72 Specaid Dearborn 8Q30
Revision date: 2/23/11
Central West Product Specifications Page 74 December 1, 2011
Central West
Product Specifications December 1, 2011 Page 75
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM MCKEE ORIGIN
Amarillo 8” Pipeline System
Premium Unleaded Gasoline
. Jan.
1-30
Feb.
1-28
Mar.
1-31
Apr.
1-30
May
1-31
June
1-30
July
1-31
Aug.
1-31
Sept.
1-15
Sept.
16-30
Oct.
1-31
Nov.
1-30
Dec.
1-31
Amarillo
13.50
8.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 A-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Albuquerque
13.50
8.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 A-3 A-2 A-2 A-2 A-1 A-1 A-2 A-2 B-2 C-3 D-4 D-4
Abernathy
13.50
8.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 A-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Rev.3, 03/30/2011
Central West
Product Specifications December 1, 2011 Page 76
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM MCKEE ORIGIN
Amarillo 8” Pipeline System
Regular Unleaded Gasoline
. Jan.
1-30
Feb.
1-28
Mar.
1-31
Apr.
1-30
May
1-31
June
1-30
July
1-31
Aug.
1-31
Sept.
1-15
Sept.
16-30
Oct.
1-31
Nov.
1-30
Dec.
1-31
Amarillo
13.50
11.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 C-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Albuquerque
13.50
11.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 C-3 A-2 A-2 A-2 A-1 A-1 A-2 A-2 B-2 C-3 D-4 D-4
Abernathy
13.50
11.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 C-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Rev.3, 03/30/2011
Central West
Product Specifications Page 77 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM MCKEE ORIGIN
Colorado Springs Pipeline System
Premium Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
Colorado Springs
15.00
8.50
8.50
8.50
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
15.00
D-5 A-4 A-4 A-3 A-3 A-2 A-2 A-2 A-2 B-2 C-3 D-4 E-5
Rev 2, 1/14/09
Central West
Product Specifications Page 78 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM MCKEE ORIGIN
Colorado Springs Pipeline System
Regular Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
Colorado Springs
15.00
13.50
8.50
8.50
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
15.00
D-5 D-4 A-4 A-3 A-3 A-2 A-2 A-2 A-2 B-2 C-3 D-4 E-5
Rev 2, 1/14/09
Central West
Product Specifications Page 79 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM MCKEE ORIGIN
El Paso Pipeline System
Premium Unleaded Gasoline
. Jan.
1-30
Feb.
1-28
Mar.
1-31
Apr.
1-30
May
1-31
June
1-30
July
1-31
Aug.
1-31
Sept.
1-15
Sept.
16-30
Oct.
1-31
Nov.
1-30
Dec.
1-31
El Paso - Local
13.50
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
10.00
11.50
13.50
13.50
D-4 A-4 A-2 A-2 A-1 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
El Paso – Tucson
13.50
9.00
9.00
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 A-3 A-2 A-2 A-2 A-2 A-1 A-1 A-1 B-2 C-3 D-4 D-4
El Paso – Phoenix
8.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
8.00
8.00
8.00
A-2 A-2 A-2 A-2 A-1 A-1 A-1 A-1 A-1 A-1 A-2 A-2 A-2
Rev 3, 03/30/2011
Central West
Product Specifications Page 80 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM MCKEE ORIGIN
El Paso Pipeline System
Regular Unleaded Gasoline
. Jan.
1-30
Feb.
1-28
Mar.
1-31
Apr.
1-30
May
1-31
June
1-30
July
1-31
Aug.
1-31
Sept.
1-15
Sept.
16-30
Oct.
1-31
Nov.
1-30
Dec.
1-31
El Paso - Local
13.50
11.50
7.00
7.00
7.00
7.00
7.00
7.00
7.00
10.00
11.50
13.50
13.50
D-4 C-4 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
El Paso – Tucson
13.50
9.00
9.00
9.00
9.00
9.00
9.00
9.00
9.00
10.00
11.50
13.50
13.50
D-4 A-3 A-2 A-2 A-2 A-2 A-1 A-1 A-1 B-2 C-3 D-4 D-4
El Paso – Phoenix
8.00
8.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
8.00
8.00
8.00
A-2 A-2 A-2 A-2 A-1 A-1 A-1 A-1 A-1 A-1 A-2 A-2 A-2
Rev 3, 03/30/2011
Central West
Product Specifications Page 81 December 1, 2011
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
13.50
11.50
10.00
8.50
8.80
8.80
8.80
8.80
8.80
10.00
11.50
13.50
13.50
D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM THREE RIVERS ORIGIN
Laredo Pipeline System
Premium Unleaded Gasoline
Laredo
Rev 3, 03/30/2011
Central West
Product Specifications Page 82 December 1, 2011
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
13.50
11.50
10.00
8.50
8.80
8.80
8.80
8.80
8.80
10.00
11.50
13.50
13.50
D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM THREE RIVERS ORIGIN
Laredo Pipeline System
Regular Unleaded Gasoline
Laredo
Rev 3, 03/30/2011
Central West
Product Specifications Page 83 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM THREE RIVERS ORIGIN
San Antonio East Pipeline System
Premium Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
San Antonio East
13.50
11.50
10.00
7.50
6.80
6.80
6.80
6.80
6.80
10.00
11.50
13.50
13.50
D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Rev 3, 8/09/10
Central West
Product Specifications Page 84 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM THREE RIVERS ORIGIN
San Antonio East Pipeline System
Regular Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
San Antonio East
13.50
11.50
10.00
7.50
6.80
6.80
6.80
6.80
6.80
6.80
11.50
13.50
13.50
D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Rev 3, 03/30/2011
Central West
Product Specifications Page 85 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM THREE RIVERS ORIGIN
San Antonio South Pipeline System
Premium Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
San Antonio South
13.50
11.50
10.00
6.50
6.80
6.80
6.80
6.80
6.80
6.80
11.50
13.50
13.50
D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Rev 3, 03/30/2011
Central West
Product Specifications Page 86 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM THREE RIVERS ORIGIN
San Antonio South Pipeline System
Regular Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
San Antonio South
13.50
11.50
10.00
6.50
6.80
6.80
6.80
6.80
6.80
6.80
11.50
13.50
13.50
D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4
Rev 3, 03/30/2011
V - Seasonal Gasoline Volatility Classes
Shipments from Origin
Reid Vapor Pressure, D5191 1/
Distillation - ASTM D86
March 1 - September 15
September 16 - February 28
Class
DVPE using EPA formula 2/
DVPE
AA A B C D E
10% Evaporated F max
158
158
149
140
131
122
50% Evaporated F min
170
170
170
170
170
170
50% Evaporated F max
250
250
245
240
235
230
90% Evaporated F max
374
374
374
365
365
365
Final Boiling Point F, max 3/
430
430
430
430
430
430
Residue, vol % max
2
2
2
2
2
2
Driveability Index, max
ASTM D4814
1250
1250
1240
1230
1220
1200
Vapor/Liquid Ratio = 20:1
Class 1
2
3
4
5
F Min. 4/ 140 133 124 116 105
1/ The RVP of all gasoline deliveries will not exceed applicable Federal, State, or ASTM
D4814, Table 2 maximums.
2/ The calculation required for the EPA compliance period is published in 40 CFR 80.46.
3/ The final boiling point of all gasoline deliveries at terminals will be at or below 437 F as
determined by ASTM D-86
4/ Although ASTM D2533 is the referee test method, D5188 or the equations in D4814 may
also be used. Rev. 1
3/13/09
Central West Product Specifications Page 87 December 1, 2011
Central West
Product Specifications Page 89 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM CORPUS CHRISTI ORIGIN
Valley Pipeline System
Premium Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
Edinburg
13.50
13.50
11.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
11.50
13.50
13.50
D-4 D-4 C-3 A-3 A-3 A-3 A-2 A-2 A-2 A-2 C-3 D-4 D-4
Rev 3, 03/30/2011
Central West
Product Specifications Page 89 December 1, 2011
SEASONAL GASOLINE VOLATILITY SCHEDULE
SHIPMENTS FROM CORPUS CHRISTI ORIGIN
Valley Pipeline System
Regular Unleaded Gasoline
. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.
1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31
Edinburg
13.50
13.50
11.50
8.50
9.00
9.00
9.00
9.00
9.00
9.00
11.50
13.50
13.50
D-4 D-4 C-3 A-3 A-3 A-3 A-2 A-2 A-2 A-2 C-3 D-4 D-4
Rev 3, 03/30/2011