NOTICE: SAVE THESE INSTRUCTIONS wARNING

Harman® • XXV Owner’s Manual_R32 • 2004 -___ • 05/151 3-90-00684c

Model(s):XXV Freestanding Pellet Stove

INSTALLER: Leave this manual with party responsible for use and operation.OwNER: Retain this manual for future reference.Contact your local dealer with questions on installation, operation or service.

NOTICE: SAVE THESE INSTRUCTIONS

Please read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow these instructions could result in property damage, bodily injury or even death.

• Donotstoreorusegasolineorotherflammablevaporsandliquidsinthevicinityofthisoranyotherappliance.

• Donotoverfire-Ifanyexternalpartstartstoglow,youareoverfiring.Reducefeedrate.Overfiringwillvoidyourwarranty.

• Complywithallminimumclearancestocombustiblesasspecified.Failuretocomplymaycausehousefire.

Checkbuildingcodespriortoinstallation.• InstallationMUSTcomplywithlocal,regional,stateand

nationalcodesandregulations.• Contactlocalbuildingorfireofficialsaboutrestrictions

andinstallationinspectionrequirementsinyourarea.

Testedandapprovedforwoodpelletfuelonly.Burningofanyothertypeoffuelvoidsyourwarranty.

Hot glass will cause burns.• Donottouchglassuntilitiscooled.• NEVERallowchildrentotouchglass.• Keepchildrenaway.• CAREFULLYSUPERVISEchildreninsameroomas

stove.• Alertchildrenandadultstohazardsofhightemperatures. High temperatures may ignite clothing or other

flammable materials.• Keepclothing,furniture,draperiesandotherflammable

materialsaway.

HOT SURFACES!

Glassandother surfacesarehotduringoperationANDcooldown.

To obtain a French translation of thismanual, pleasecontactyourdealerorvisitwww.harmanstoves.com.

Pourobtenirunetraductionfrançaisedecemanuel,s’ilvous plaît contacter votre revendeur ou visitezwww.harmanstoves.com.

NOTE

wARNING

wARNING

Owner’s ManualCare and Operation

XXVUse&CareVideo

CAUTION!

CAUTION!


DANGER: Risque d’électrocution. Débrancher l’appareil avant toute intervention.Ne remplacer la vitre qu’avec une vitre céramique 5 mm de même qualité disponible auprès de votre revendeur.Pour une information plus complète, se reporter à la notice d’utilisationTenir la porte frontale et le couvercle de trémie hermétiquement clos durant le fonctionnement de l’appareil.Puissance calorifi que émise: Nominale: 10.5 KW Réduite: 1.8 KW Concentration CO (à 13 % O2)à puissance nominale: < 0.02 % à puissance réduite: < 0.04 %Rendement: à puissance nominale: 84 % à puissance réduite: 73%dISTANCeS de SeCURITe PAR RAPPORT AUX MATeRIAUX COMBUSTIBLeSEntre Mur Arrière et appareil 76 mmEntre Paroi latérale et appareil 305 mmInstallation en angleEntre murs et apparell 159 mmInstallation en alcôveHauter minimale de l’alcôve 1524 mmParois latérales de l’alcôve 305 mmProfondeur maximale de l’alcôve 914 mmPROTeCTION dU PLANCHeRCôtés 200 mmArrière 200 mmAvant 450 mm*mesurer à partir de la surface de la porte en verre.Utiliser une protection de sol non combustible sous l’appareil qui s’étend sur les côtés. l’avant et l’arrière du poêle (voir schéma).ll est recommandé que la protection s’étende jusque sous le conduit en cas d’installation d’un conduit horizontal ou sous le té en cas de conduit vertical.

Model: XXVResidential Space Heating Appliance Fire by Wood Pellets

This pellet burning appliance has been tested and listed for use in Manufactured Homes in accordance with OAR 814-23-900 through 814-23-909

OMNI-Test Laboratories, Inc.Report #/Rapport #135-S-14-2, 135-S-14b-6, 135-S-14c-6.2

“PReVeNT HOUSe FIReS” Install and use only in accordance with the manufacturer’s installation and operation instructions. Contact local building or fi re offi cials about restrictions and inspection in your area.WARNING: FOR MANUFACTURed HOMeS: Do not install appliance in a sleeping room. An outside combustion air inlet must be provided. The structural integrity of the manufactured home fl oor, ceiling and walls must be maintained.Refer to manufacture’s instructions and local codes for precautions required for passing chimney through a combustible wall or ceiling. Inspect and clean exhaust venting system frequently in accordance with manufacturer’s instructions. Use a 3” or 4” diameter type “L” or “PL” venting system.Do not connect this unit to a chimney fl ue servicing another appliance.FOR USe WITH PeLLeTIZed WOOd FUeL OR CORN/PeLLeT MIXTURe ONLY.CONSULT MANUFACTUReR’S INSTRUCTIONS.Input Rating Max: 5.7 lb. fuel/hrElectrical Rating: 240 VAC, 50 Hz, Start 2.6 AMPS, run 2.0 AMPSU.S. Electrical Rating: 115 VAC, 60Hz, Start 4.2 AMPS, Run 3.6 AMPSEmissions of CO in combustions:Nominal Heat Output: .02%, Reduced Heat Output:.04%Flue Gas Temperature: 224 CThermal Output: 10.5kWEnergy Effi ciency: Normal: 84%, Reduced: 73%Fuel Type: Wood Pellets, 5mm diameter, 20mm LomgRoute power cord away from unit.dANGeR: Risk of electrical shock. Disconnect power supply before servicing.Replace glass only with 5mm ceramic available from your dealer.For further instruction refer to owner’s manual.Keep viewing and ash removal doors tightly closed during operation.

CLeARANCeS TO COMBUSTIBLeSBack Wall to Appliance 3”Side Wall to Appliance 12”

Corner InstallationWalls to Appliance 6.25”

FLOOR PROTeCTION USA CANADASides (A)* 6” 200MMBack (B) 0” 200MMFront (C)* 6” 450MM*Measured from window opening in the US ONLY.

Use a non-combustible fl oor protector extending under unit and to the sides, front and back of unit as shown in Floor Protector Diagram. Measure front distance from the surface of the glass door.Recommended: Non-combustible fl oor protection extending beneath the fl uepipe when installed with horizontal venting or under the top vent adapter with vertical installation.

dO NOT ReMOVe THIS LABeL

MAde IN THe USA

U.S. eNVIROMeNTAL PROTeCTION AGeNCYThis model is exempt from EPA certifi cation under 40 CFR 60.531 by defi nition [Wood Heater (A) “Ait-to-Fuel Ratio”].

2013 2014 2015 JAN FEB MAR APR MAy JUN JUL AUG SEP OCT NOV DECdate of Manufacture/date de Fabrication:

Hearth and Home Technologies - 352 Mountain House Road -Halifax, PA 17032

BARCODE LABEL

AGeNCe AMÉRICAINe POUR LA PROTeCTION de L’eNVIRONMeNTCe modéle est dispensé par ePA certifi cation d’aprè 40 CFR 60.531 par dèfi nition [Appareil à bois(A) Ratio air/combustion]

Test to/testé à ASTM E 1509-04, ULC/ORD-C1482-M1990, ULC-S627-00Tested by Emitech, Apave & BFP ElectroniqueEN60335-1, EN55014-1, EN 61000-3-2, EN 14785:2005Test date: February 2004Room Heater Pellet fuel Burning type (UM) 84-HUD

008Serial No.No de série:

Test réalisés par OMNI-Test Laboratories, Inc.Essais Selon les normes 1509-04 de l’ASTM, C1482-M91ULCAppareil de chauffage à granulés (UM) 84- HUDNORMeS eUROPÉeNNeS:NF EN 14785 CETIAT – Déc. 2006AEMC MESURES EN50366 – Déc. 2006EMITECH, APAVE & BFP Electronique – Fév. 2004EN55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3Respecter scrupuleusement les instructions du constructeur pour l’installation et les consignes de fonctionnement. Respecter les règles de sécurité en vigueur dans votre région.AVeRTISSeMeNT POUR MOBILe HOMeS: Ne pas installer dans une chambre. ll est inpératif de prévoir une prise d’air extérieur. L’intégrité structurale du plancher, du plafond et des murs doit être strictment préservée.Se reporter aux instructions du fabricant et aux réglementations spécifi ques locales concernant les précautions requises lors de la traversée d’un mur ou d’un plafond. Contrôler et nettoyer fréquemment toul le système d’évacuation des fumées conformément aux recommandations du constructeur.Utiliser des conduits « spécial granuléls » de diamètre 80 mm ou 100 mm.Ne pas raccorder ce poêle à un conduit de cheminée déjà utilisé.FONCTIONNe eXCLUSIVeMeNT AVeC deS GRANULeS de BOIS.Se CONFORMeR AUX INSTRUCTIONS d’UTILISATIONConsommation maximale: 2.9 kg/hCaractéristiques électriques: 240 VC, 50 Hz, Intensité au démarrage 2.6 A, Intensité fonctionnement normal 2.0 ATenir le cordon d’alimentation à l’écart du poéle.

Modèle: XXVAppareil de chauffage à granulés de bois

Harman XXV Pellet Stove

Rev FP.N. 3-90-00025

Ne pas enlever cette étiquette Fabriqué aux USA

5.5"

Floor Protection

6.25”

6.25”

Floor Protection

12”

3”

Floor Protection C

B

A A

10.5"

Floor Protection

36”

12” 12”

Listing Label Information/Location

A. CongratulationsCongratulationsonselectingaHarman®FreestandingPelletStove.TheHarman®XXVpelletstoveyouhaveselectedisdesignedtoprovide theutmost insafety, reliability,andefficiency.Astheownerofanewpelletstove,you’llwanttoreadandcarefullyfollowalloftheinstructionscontainedinthisowner’smanual.Payspecialattentiontoallcautionsandwarnings.

Themodelinformationregardingyourspecificstovecanbefoundontheratingplateusuallylocatedinthecontrolareaofthestove.

Read this manual before operating this appliance. Please retain this Owner’s Manual for future reference.

Read the Installation Manual before making any installation or finishing changes.

1 welcome

Brand:________________________________________________ ModelName:___________________________

SerialNumber:__________________________________________ DateInstalled: __________________________

Appliance Information:

Local Dealer InformationDEALER: Fill in your name, address, phone and email information here and appliance information below.

DealerName:________________________________________________________

Address:____________________________________________________________

____________________________________________________________

Phone:_____________________________________________________________

Email:_____________________________________________________________

SerialNumber

ModelName

Thisowner’smanual shouldberetainedforfuturereference.We suggest that you keep it with your other importantdocumentsandproductmanuals.YournewHarman®XXVPelletStovewillgiveyouyearsofdurableuseandtrouble-freeenjoyment.WelcometotheHarman®family!


Table of Contents

1 welcome A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Product Specific and Important Safety Information A. ApplianceCertification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4B. MobileHomeApproved. . . . . . . . . . . . . . . . . . . . . . . . . . . 4C. BTU&EfficiencySpecifications. . . . . . . . . . . . . . . . . . . . . 5

3 General Information A. ApplianceSafety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6B. ClearSpace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6C.ControlExplanation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7D. FuelSpecification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8E. GeneralOperatingInformation. . . . . . . . . . . . . . . . . . . . . . 9F. BeforeYourFirstFire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 Operating Instructions A. StartingYourFirstFire. . . . . . . . . . . . . . . . . . . . . . . . . . . 10B. FireCharacteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10C. FeedLimitAdjustmentInstructions . . . . . . . . . . . . . . . . . 10D. IgnitionCycles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11E. AutomaticIgnition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Maintenance and Service A. ProperShutdownProcedure. . . . . . . . . . . . . . . . . . . . . . 14B. QuickReferenceMaintenanceChart. . . . . . . . . . . . . . . . 14C.GeneralMaintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14D.GlassMaintenance..............................15E. BurnpotMaintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16F. CombustionBlowerChamber . . . . . . . . . . . . . . . . . . . . . 17G.PelletFeederChamber . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Safety Alert Key:• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.• NOTICE: Used to address practices not related to personal injury.

!

6 Troubleshooting and Frequently Asked Questions A. ErrorCodeDescription. . . . . . . . . . . . . . . . . . . . . . . . . . . 19B. FrequentlyAskedQuestions . . . . . . . . . . . . . . . . . . . . . . 19C. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7 Reference Materials A. SafetyReminders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21B. MotorandComponentLocation. . . . . . . . . . . . . . . . . . . . 22C. LossofPower..................................23D. EmergencyManualIgnition. . . . . . . . . . . . . . . . . . . . . . . 23E. ServiceParts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24F. WarrantyPolicy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31G.ContactInformation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

= Contains updated information


2 Product Specific and Important Safety Information

A. Appliance Certification B. Mobile Home ApprovedThis appliance is approved formobile home installationswhennotinstalledinasleepingroomandwhenanoutsidecombustionairinletisprovided.Thestructuralintegrityofthemobilehomefloor,ceiling,andwallsmustbemaintained.Theappliancemustbeproperlygroundedtotheframeofthemobilehomeanduseonlylistedpelletvent,Class“PL”connectorpipe.AHarman®OutsideAirKitmust be installed in amobilehomeinstallation.

NOTE: Thisinstallationmustconformwithlocalcodes.In the absence of local codes youmust complywiththeASTM E1509-2004, ULC S628-93, ULC/ORD-C-1482-M1990, (UM) 84-HUD

THE STRUCTURAL INTEGRITy OF THE MANUFACTURED HOME FLOOR, wALL, AND CEILING/ROOF MUST BE MAINTAINED.

DO NOT INSTALL IN SLEEPING ROOM.

WARNING!

TheXXVisCertifiedtocomplywith2015particulate emission standards. NotapprovedforsaleafterMay15,2020.

MODEL: XXVPelletStoveLABORATORy: OMNITestLaboratories,IncREPORT NO. 0135PS014STyPE: PelletFueled/SupplementaryFor

ResidentialUseSTANDARD(s): ASTME1509-04,ULC/ORD-

C1482-M1990,ULC-S627-00,EPAMethod28&5G

ELECTRICAL RATING

115 VAC, 60 Hz, Start 4.2 Amps,Run2.8Amps

GLASS SPECIFICATIONS 5mmmirroredceramicglass


C. BTU & Efficiency Specifications

NOTE: Hearth&HomeTechnologies,manufacturer ofthisappliance,reservestherighttoalteritsproducts,theirspecificationsand/orpricewithoutnotice.

*An efficiency based on EPA historical data of 78% **Actual tested Higher Heating Value (HHV) efficiency and data collected during EPA emissions test ***A range of BTU outputs based on EPA default efficiency and the burn rates from the low and high EPA tests ****Based on the maximum feed rate per hour multiplied by approximately 8,600 BTU’s which is the average BTU’s from a pound of pellets.Thiswoodheaterhasamanufacturer-setminimumlowburnratethatmustnotbealtered.Itisagainstfederalregulationstoalter thissettingorotherwiseoperate thiswoodheaterinamannerinconsistentwithoperatinginstructionsinthismanual.Thiswoodheaterneedsperiodicinspectionandrepairforproperoperation.Itisagainstfederalregulationstooperatethiswoodheater in amanner inconsistentwith operatinginstructionsinthismanual.

Harman® is a registered trademark of Hearth & HomeTechnologies.

WARNING!Risk of Fire! Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the below actions.DO NOT: • Install or operate damaged appliance • Modify appliance • Install other than as instructed by Hearth & Home

Technologies • Operate the appliance without fully assembling all

components • Overfire • Install any component not approved by Hearth &

Home Technologies • Install parts or components not Listed or approved. • Disable safety switchesImproper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified installer, service agency or your dealer.

EPA Certification Number: 994-15EPA Certified Emissions: 1.8g/hr*EPA Default Efficiency: 78%**Actual Tested Efficiency: 66.5%***EPA BTU Output: 36,900****BTU Input 50,000Vent Size: 3InchHopper Capacity: 65lbsFuel WoodPellet


WARNING! DO NOT operate stove before reading and understanding operating instructions. Failure to operate stove according to operating instructions could cause fireorinjury.

If you expect that small children or vulnerable adultsmaycomeintocontactwiththisappliance,thefollowingprecautionsarerecommended:• Installaphysicalbarriersuchas: - Adecorativefirescreen. - Adjustablesafetygate.• Installaswitchlockorawall/remotecontrolwithchild

protectionlockoutfeature.• Keepremotecontrolsoutofreachofchildren.• Neverleavechildrenalonenearahotstove,whether

operatingorcoolingdown.• TeachchildrentoNEVERtouchthestove.• Consider not using the stovewhen childrenwill be

present.Contactyourdealerformoreinformation,orvisit:www.hpba.org/safety-information.To prevent unintended operation when not using yourstove foranextendedperiodof time(summermonths,vacations,trips,etc):• Unplugstovefromreceptacle.

A. Appliance Safety

ContactyourdealerorHearth&HomeTechnologiesifthebarrierisnotpresentorhelpisneededtoproperlyinstallone.

HOT SURFACES!GlassandothersurfacesarehotduringoperationANDcooldown.

Hot glass will cause burns.• DO NOTtouchglassuntilitiscooled• NEVERallowchildrentotouchglass• Keepchildrenaway

• CAREFULLYSUPERVISEchildreninsameroomasstove.• Alertchildrenandadultstohazardsofhightemperatures.

High temperatures may ignite clothing or other flammable materials.• Keep clothing, furniture, draperies and other flammablematerialsaway.

3 General Information

wARNING!

B. Clear Space

WARNING!RISK OF FIRE! DoNOTplacecombustibleobjectsin front or to the sides of the appliance. High temperatures may ignite clothing, furniture or draperies.

Mantel: Avoid placing candles and other heat-sensitiveobjectsonmantelorhearth.Heatmaydamagetheseobjects.

WARNING!RISK OF FIRE! Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.• Do NOT store flammable materials in the appliance’s

vicinity.• Do NOT use gasoline, lantern fuel, kerosene, charcoal

lighter fluid or similar liquids to start or “freshen up” a fire in this heater.

Keep all such liquids well away from the heater while it is in use as combustible materials may ignite.

NOTICEClearances may only be reduced by means approved by the regulatory authority having jurisdiction.

WARNING!


C. Control ExplanationMode Selector Allows you to choose between Room Temp Mode, Constant Burn Mode, or OFF. Also allows you to vary the distribution blower speed by turning the knob to the high or low side of each mode.

Feed LimitSets the maximum feed rate

TestRuns all motors at full speed for one minute to check operation. After a minute, the control will simulate a minimum burn and the combustion blower will remain on low.

Dist r ibut ion Blower speed adjustment range.

L = lowH = high

V a r i a b l e s p e e d anywhere between L and H; although as the stove temp. goes up, so does the L and H scale.

Power LightIndicates power to the control.

Indicates power to the feed motor.

Indicates power to combustion blower

Status LightWill be lit in either stove or room temp mode when pointer is not within off position band except after normal shut down. Blinks to indicate errors listed below.

Indicates power to distribution blower.

Indicates igniter is on.

Igniter switchSet to appropriate Start-Up mode.

Temp dialAllows you to adjust the room tempera tu re i n Room Temp Mode using the outer scale marked in degrees Fahrenheit. It also allows you to adjust the stove temperature while in Constant Burn Mode using the inner scale marked from 1 to 7.

Dealer Diagnostic PortFor dealer maintenance only. Requires special DDM monitor supplied to Harman® Dealers exclusively.


NOTICEHearth&HomeTechnologiesisnotresponsibleforstoveperformanceorextramaintenancerequiredasaresultofusingfuelwithhigherashormineralcontent.

Size• Pellets are either 1/4 inch or 5/16 inch (6-8mm) in

diameter• Lengthshouldbenomorethan1-1/2inches(38mm)• Pellet length can vary from lot to lot from the same

manufacturer.Performance• Higherashcontentrequiresmorefrequentmaintenance.• “Premium” grade pelletswill produce the highest heat

output.• Burning pellets longer than 1-1/2 inches (38mm) can

causeinconsistentfeedingand/orignition.

Werecommendthatyoubuyfuelinmulti-tonlotswheneverpossible. However, we do recommend trying differentbrands prior to purchasing multi-ton lots, to ensure yoursatisfaction.

Storage• Woodpelletsshouldbeleft intheiroriginalsealedbag

untilreadytouse,topreventmoisture.• Donotstorefuelwithinthespecifiedclearanceareas,or

inalocationthatwillinterferewithroutinecleaningandmaintenanceprocedures.

D. Fuel SpecificationsFuel and Fuel StoragePellet fuel quality can fluctuate from manufacturer tomanufacturer,andevenfrombagtobag.Hearth&HomeTechnologiesrecommendsusingonlyfuelthatiscertifiedbythePelletFuelsInstitute(PFI).

FuelMaterial• Madefromsawdustand/orotherwoodby-products• Sourcematerialtypicallydeterminesashcontent

HigherAshContentMaterial• Hardwoodswithhighmineralcontent• Barkandleavesassourcematerial• “Standard”gradepelletsandotherbiomass

LowerAshContentMaterial• Softwood;pine,fir,etc.• Materialswithlowermineralcontent• “Premium”gradepelletsClinkersMinerals and other non-combustiblematerials, like sand,willturnintoahardglass-likesubstancewhenheated.Treesfromdifferentareaswillvaryinmineralcontent.Forthis reason, some fuels will produce more clinkers thanothers.

MoistureAlwaysburndryfuel.Burningfuelwithhighmoisturecontenttakesenergytodryandtendstocool theappliancethus,robbingheatfromyourhome.Damppelletfuelcouldturnbackintosawdustwhichdoesnotflowproperlythroughthefeedsystem.

Tested and approved for use with wood pellets ONLY.Burningofanyotherfuelwillvoidyourwarranty.

CAUTION!


F. Before your First Fire1. First, make sure your appliance has been properly

installedandthatallsafetyrequirementshavebeenmet.Payparticularattentiontothefireprotectionandventinginstructions.

2. Doublecheckthattheashpanandfireboxareempty!3. Closethefrontdoor.

E. General Operating Information1. Room Sensor Calls For HeatTheapplianceislikemostmodernfurnaces;whentheroomsensorcallsforheat,yourappliancewill automaticallylightanddeliverheat.Whentheroomisuptotemperatureandtheroomsensorissatisfied,theappliancewillshutdown.2. Heat Output ControlsThe appliancewill turn on and off as the room sensordemands.Whentheroomsensorcallsforheat,theappliancewillalwaysstartuponHigh.Afterburningapproximately7-10minutes,theappliancewillthenburnattherateatwhichitwasoriginallyset.Iftheapplianceissetatoneofthelowersettings,itwillrunquieterbuttakelongertoheatupanareathanifitweresetatahigherburnrate.Regardlessoftheburnrate,whentheareaiswarmenoughtosatisfytheroomsensor,theappliancewillshutoff.

FireHazard.Keepcombustiblematerials,gasolineandotherflammablevaporsandliquidsclearofappliance.

wARNING!

• DoNOTstoreflammablematerialsintheappliance’svicinity.

• NEVERUSEGASOLINE,GASOLINE-TYPE LANTERNFUEL,KEROSENE,CHARCOAL LIGHTERFLUID,ORSIMILARLIQUIDSTOSTARTOR“FRESHENUP”AFIREINTHISHEATER.KEEPALLSUCHLIQUIDSWELLAWAYFROMTHEHEATERWHILEITISINUSE.

• DONOTBURNGARBAGEORFLAMMABLEFLUIDSSUCHASGASOLINE,NAPHTHAORENGINEOIL.

• DONOTUSECHEMICALSOFFLUIDSTOSTARTTHEFIRE.

• Combustiblematerialsmayignite.

Figure 3.1


B. Fire CharacteristicsAproperlyadjustedfirehasamediumactiveflamepatternthat extends out of the burn pot approximately 6 inches(152mm).

C. Feed Limit Adjustment InstructionsTheFeedLimitcontrol is factorysetat#4,andshouldbeadequateformostfuels.However,iftheflameheightistoohighortoolow,youwillneedtoadjustthefeedrate.Waituntiltheappliancehasbeenburningfor15minutesbeforemakingyouradjustmentsandallow15minutesfortheFeedLimittotakeeffect.

A. Starting your First Fire1. A roomsensor is required for proper operationof this

appliance in “RoomTemp”mode.At this time, fill thehopperwith pellets, insure the control is set to “OFF”.Figure4.2.Plugthepowercordintoaproperlygrounded,nearbyoutlet.

2. Oncepowerispresent,theunititwillrunthroughaquickdiagnosticstesttoinsurethecontrolisoperatingproperly.Thisisnormal.

3. ForyourfirstfireitmaybenecessarytopurgetheaugersystembyputtingthefeedLimitknobto“Test”prior tostarting theunit.Figure4.3.This insures thatplentyoffuelenterstheburnpotforproperignition.

4. Flip toggle switch to desiredmode “auto orDisabled”.Figure4.4.SetFeedLimitknobtodesiredsettingandturnmodedialto“RoomTemp”or“ConstantBurn”Figure4.5.Note:Feedrateof#4isagoodstartingpoint.Adjustmentsmadeneedtobemadedependingonfuelqualityand/orheatoutputdesired.

5. Thefuelfeedsystemandtheignitershouldnowbeon.6. Oncetheappliancehasignited,letitburnforapproximately

7-10minutes.After this time the unit should begin tooperateperthesettingsatthecontrol.

Figure 4.5

Odorsandvaporsreleasedduringinitialoperation.• Curingofhightemperaturepaint.• Openwindowsforaircirculation.

Odorsmaybeirritatingtosensitiveindividuals.

Figure 4.2 Figure 4.3

Figure 4.4

4 Operating Instructions

CAUTION!


D. Ignition Cycles1. Atthebeginningofeachignitioncycle,itisnormaltosee

somesmokeinthefirebox.Thesmokewillstoponcethefirestarts.

2. Thedistributionblowerwillautomaticallyturnonafteryourappliancehasreachedthesettemperature.Thisblowertransfersheatfromyourapplianceintotheroom,andwillcontinuetorunin“ConstantBurn”modeatthesetspeedyouhavethecontrolknobat.In“roomtemp”mode however, the blowerwill turn on and offinaccordance towhat temperature theroomsensor isreading.Whentheroomsensorissatisfiedtheblowerwillshutdownuntiltheroomsensorseesademandforheat.

3. Occasionallytheappliancemayrunoutoffuelandshutitselfdown.Whenthishappens,theunitwillneedtobeturnedtotheoffpositionandrestarted. Ifneeded,followSectionA, “StartingYourFirstFire”.

FireRiskDoNOToperateappliance:• Withappliancedooropen.• Burnpotflooropen.• Cleaningslideplatesopen.DoNOTstorefuel:• Closerthanrequiredclearancestocombustibles

toappliance• Withinspacerequiredforloadingorashremoval.

WARNING!


Igniter Switch to "AUTO" (up position)Makesuretheunitispluggedintoaproperlygrounded,120VAC,60Hzelectricalsource.Thepowerlightshouldbetheonlylightlit.

Note: Be sure there is no fuel or other combustibles in the ash pan prior to lighting.

1. TurnModeSelectorto"OFF".

2. Fillhopperwithpellets.

3. Cleanburnpotwithscraper,ifnecessary.

4. Ifstartingafteranemptyhopper,turnFeedLimitto"TEST"(forone60secondcycle).2Thiswillflowpelletsintotheauger tubeandalsoallowyoutocheck themotors foroperation.

NOTE: The auger motor will not operate with the view door open.

5. TurnFeedLimitto#4.4

6. FliptheIgniterSwitchupintothe"AUTO"position.

7. TurntheTemperatureDialtothedesiredroomtemperature.

8. TurnModeSelectortoRoomTemperatureorConstantBurn.

9. Fillhopperwithpelletsandremoveashesasrequired. Keep thehopper lid and fireboxdoors closedwhile inoperation.Maintaindoorsealsingoodcondition.Failuretodosowillaffectoperationof theapplianceandmaypermitescapeofsmokeorgasesintothelivingspace.

1. Fines are small pieces of broken pellets (sawdust). Fines do not flow easily and often build up on the hopper funnel bottom angles. These fines can be pushed into the feeder opening and then fill the hopper with pellets. As the system works, they will be burned.

2. The "TEST" cycle will operate the feed motor for exactly one minute. Turning to "TEST" again and again may load too much fuel into the burn pot causing excessive smoke on start-up.

3. The firebox low pressure switch will not allow the auger motor or the igniter element to operate if the view door is open.

4. Adjust Feed Rate. If this is your first fire or you are trying different pellets, set the Feed Limit to #4, Figure 4.6 This is a conservative number and will probably need to be increased. After you know a feed rate setting that works well, use that setting. Remember, if your feed rate is too high you may waste fuel.

5. This is usually a weekly maintenance procedure. Cleaning the burn pot with the scraper with a small amount of new fuel in the bottom is not a problem. First, scrape the ashes off the front of the burn pot into the ash pan. Then scrape the holed surface downward into the burn pot. When the stove feeds, these scrapings will be pushed out by the feeder.

6. The ash pan can hold the ashes from approximately 1 ton of premium fuel. This means the ashes will only need to be emptied a few times a year.

7. Setting the Feed Limit # for maximum burn: With the unit burning in "AUTO", turn to "Stove Mode" and put the fan on "H". Set the Temperature Dial to #7. Allow the unit to burn for about 30 minutes and check ash on front of burn pot. Figure 4.7. If the ash line is larger than 1", turn the Feed Limit from #4 to #5. Allow another 30 minutes of burn time and check again. If, at #6 setting, a 1" or less ash bed is not obtainable, it is not a problem. The 1" ash bed is only at maximum burn rate and during normal operation, the ash bed will be larger.

NEVER USE GASOLINE, GASOLINE-TyPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR 'FRESHEN UP' A FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS wELL AwAy FROM THE HEATER, wHILE IN USE.

BURNING GARBAGE, USE OF IMPROPER FUELS, FIRE STARTERS OR ALTERING THE STOVE FOR HIGHER HEAT OUTPUT MAy CAUSE DAMAGE TO THE STOVE AND COULD RESULT IN A HOUSE FIRE. USE ONLy APPROVED FUELS AND FOLLOw ONLy THESE OPERATION GUIDELINES.

Figure 4.6

See Note 71"

Figure 4.7

E. Automatic Ignition

WARNING!

WARNING!


TheXXVPelletStoveismorethanjustautomaticignition,itisalsoautomatictemperaturecontrol.Theautomaticsystemwillallowthefiresizetobeadjustedtomatchtheheatingneedsandevenputthefireoutifnecessary.Ifheatisneededafterthefireisout,theXXVPelletStovewillautomaticallyre-igniteandadjustthefiresizetomatchtheheatingneed.Thetotallyautomaticroomsensormodeisrecommendedbecauseofitsefficiency.Theunitcanbeswitchedbetween"AUTO"and"DISABLED"atanytimeduringoperation.Igniter switch to “AUTO”Room Temperature ModeIn“RoomTempMode”heatoutputiscontrolledautomaticallybytheRoomSensingProbe.WhentheRoomSensingProbecallsforheat,thestovewillincreaseoutput.WhentheRoomSensingProbeisgettingclosetothesettemperature,thestovewillbegintoleveloffoutputandkeepthefireburningatjusttherighttemperaturetomaintainthatsetting.High output is determined by the feed rate setting.Thissetting,generallyon#4,canbeincreasedifhigherburnratesarenecessary(Figure4.6).Theunit’smaximumburnrateshouldnotcreatelessthan1”ofashontheburnpotfrontedge(Figure4.7).Overfeedingisnotasafetyconcern,butfuelmaybewastedifunburnedpelletsfallintotheashpan.In“RoomTempMode”aconstantfuelconsumptionrateissacrificedforexactroomtemperature.Therefore,asitgetscoldermorepelletswillbeburnedautomatically.The distribution blower speedwill vary according to thepositionofthemodeselectorpointer,andfiresize.Igniter switch to “AUTO”Constant Burn ModeThisallowsforautomaticignitionuponstart-uponly.Theunitcanthenbesetatanydesiredsetting.Theheatoutputandfuel consumptionwill remainconstant regardlessof roomtemperature.Theunit’smaximumfeedrateshouldnotcreatelessthan1”ofashontheburnpotfrontedge.Figure4.7.Theunit’slowburnormaintenancesettingisaslowasitwillgo.Itwillnotgooutunlessitrunsoutoffueloristurnedoff.Shut-Down ProcedureTo kill the fire or stop burning the stove, turn theModeSelector to“OFF”.Thiswillcausethefire todiminishandburnout.Whenthefireburnsoutandthestovecoolsdowneverythingwillstop.Ifyoupulltheplugtoshutdownthestove,allmotorswillstop.Thismaycauseincompletecombustionandsmokeinthefirebox.Iftheloaddoorisopened,thesmokemayescape.Thebestwaytoshutdownthestoveissimplyletitrunoutofpellets,thenthestovewillshutdownautomatically.

Room Temperature Mode: This setting will produce a room temperature of 70 degrees with the distribution blower at medium speed.

This setting will produce medium heat with the distribution blower on "low".

This setting will produce continuous maximum heat output with the distribution blower at full speed.

Constant Burn Mode

E. Automatic Ignition (Continued)


Types of FuelThetypeoffuelyouareburningwilldictatehowoftenyouhavetocleanyourburnpot.

Ifthefuelyouareburninghasahighdirtorashcontent,itmaybenecessarytocleantheburnpotmorethanonceaday.

Dirtyfuelwillcauseclinkerstoformintheburnpot.Aclinkerisformedwhendirt,ashoranon-burnablesubstanceisheatedto2000°F(1093°C)andbecomesglass-like.

B. Quick Reference Maintenance Chart

Follow the detailed instructions found in this section for each step listed in the chart below.

Cleaning or Inspection Frequency Daily weekly Monthly yearlyAshPan Every5bagsoffueldepending

onthefueltypeorashbuild-upOR X

AshRemovalfromFirebox Every5bagsormorefrequentlydependingonthefueltypeorashbuild-up

OR X

HeatExchanger Every1tonoffuel OR XBlower,Combustion(Exhaust) Morefrequentlydependingon

thefueltypeOR X

Blower,Distribution Every25bagsormorefrequentlydependingonthefueltype

OR X

DoorGasketInspection Priortoheatingseason OR XExhaustPath Morefrequentlydependingon

ashbuild-upOR X

Firebox-PrepareforNon-BurnSeason Atendofheatingseason OR XBurnpot-Burningpellets-hardwood Every3bags OR XBurnpot-Burningpellets-softwood Every5bags OR XGlass Whenclearviewofburnpot

becomesobscureOR X

Hopper/HopperLidGasket Every50bagsoffuelorwhenchangingfueltypes

OR X

VentingSystem Morefrequentlydependingonthefueltype

OR X

5 Maintenance & Service

A. Proper Shutdown Procedure

C. General MaintenanceWhenproperlymaintained,yourstovewillgiveyoumanyyearsoftrouble-freeservice.Contact your dealertoanswerquestionsregardingproperoperation,trouble-shootingandserviceforyourappliance.Visitwww.harmanstoves.comtofindadealer.Werecommendannualservicebyaqualifiedservicetechnician.

Shock and Smoke Hazard• Turnunittotheoffposition,letappliancecompletelycoolandcombustionblowermustbeoff.Nowyoucanunplugappliancebeforeservicing.

• Smokespillageintoroomcanoccurifapplianceisnotcoolbeforeunplugging.

• Riskofshockifappliancenotunpluggedbeforeservicingappliance.

CAUTION!


Glass Gasket

Replace glass only with high temperature ceramic glass.

Inspect door gasket during cleaning and inspection

D. Glass MaintenanceThe glass used in your stove is manufactured to exact standards to withstand the high heat of the fire, but like all glass, it must be treated with common sense and care. Never abuse the glass by slamming the door shut or striking the glass with a heavy object. If the glass is broken or damaged, do not operate the stove until it has been replaced.Glass - CleaningSometimes itwillbenecessary tocleanaccumulatedashfromtheglasssurface;allowingthisashtoremainontheglassforlongperiodscanresultin“etching”duetotheacidityoftheash.Nevercleantheglasswhileitishot,anddo not useabrasivesubstances.Washthesurfacewithcoolwater,andrinsethoroughly.Youmaywishtouseanon-abrasivecleanerspecificallydesignedforuseonstoveglass.Inanycase,drythoroughlybeforerelightingyourstove.Glass - ReplacementIfthestove’sglassiscrackedorbroken,youmustreplaceit beforeoperating your stove. Removepieces carefully.ReplaceglassonlywithHarman® replacementglass;do not use substitutes.Carefullyremovedamagedglass,gasketmaterial,andholddownclips(setaside).Installtheselfadhesive1/4””gasketmaterialaroundthefrontfaceoftheglass.Settheglasspanelandgasketgentlyontothedoor.Installtheholddownclipsandtightenwithbolts.


Whenaddingfuel,taketheopportunitytocleantheburnpot.(weekly at minimum)• Scrapethetopholedsurfaceandsidesoftheburnpot

down to auger tubeFigure 5.1. It is not necessary tocompletely removeallmaterial from theburnpot.Theexcesswillbepushedoutduringthenextuse.

• With the fire out and burn pot cold, use the suppliedallenwrench to remove any build-up thatmay haveaccumulated intheholesof theburnpotgrate.Simplypushtheallenwrenchdownthrougheachholeensuringitisclearofanybuild-uppayingattentionnottodamagetheigniterelementintheprocess.

Monthly, or after each ton of fuel burned:• Loosenthe(2)wingthumbscrewsonthelowerfrontangle

oftheburnpot.Figure5.2• Liftofftheclean-outcovertoopenthebottomclean-out

chamber.Figure5.3

• Cleanashbuildupfrominsidethechamberwhilecoverisoff.Usethescrapertotaponthetopfrontedgeoftheburnpot.Thiswill helpknockpiecesofash, loosenedbythescrapingprocess,downthroughtheholes.Italsohelpsknockscaleoffoftheigniterelement.

Figure 5.3Theigniterismadetoberemovableforservicebyinsulatedmale/femalewireconnectors.Theseconnectionsbetweenthehot leads(thewires inside theburnpot)and thecoldleads(thewiresfromthecontrolboard)arealwayspulledtotheinsiderearofthefeederbody. (Not coiled inside the burn pot.)Itisveryimportantthattheseconnectionsaretotheinsiderearofthefeederbody.Also,theextrawireoftheigniterwireserviceloopmustbepulledoutthroughtherearofthefeederandtiedupsothatitwillnotbedamagedbyanymovingparts.

Note: The hot lead/cold lead connection must always be pulled to the rear of the feeder body before operation.Viewed from below through the ash pan opening.

Igniter hot lead wires(High temperature)

Burn pot igniter

E. Burnpot Maintenance

Figure 5.1

Figure 5.2

Figure 5.3

Wing Thumb Screws

Use caution when cleaning burn pot clean-out chamber. Do not damage the high temperature igniter wires.

CAUTION!

Disconnect the power to the unit before removing cover.

dANGeR!


Monthly Cleaning- continued:CleantheheatexchangerwithscraperasshowninFigure5.4.Brushorscrapetheinsideofthestovetoremoveflyash.Removetheashpananddisposeofashesinanapprovedmanner,accordingtolocalcodes.The exhaust passagemay need cleaned aswell. KeepinmindtheESPSensorislocatedjust insidetheexhaustpassageFigure5.7.BesurenottodamagetheESPSensorwhilecleaningthisarea.• Removethecombustionblowerbylooseningthe3wing

nuts(Figure5.5),twistingthecombustionblowermountplatecounterclockwisetounlock,andpullingtheblowerout.

• CleanthecombustionblowerhousingandfanbladewithabrushandavacuumcleanerFigure5.6.

Note:Donotuseahouseholdvacuumtocleanthestove.WerecommendthatyouuseashopvacuumthatisequippedwithafinedustfiltercalledaHEPAfilteroravacuumspeciallymadeforflyashandsoot.USINGAVACUUMWHICHISNOTEQUIPPEDWITHAFINEDUSTFILTERWILLBLOWFLYASHANDSOOTOUTINTOTHEROOM.NOTE:THESTOVEMUSTBECOMPLETELYOUTBEFOREYOUVACUUMTHESTOVE.LIVEPELLETEMBERS, IFSUCKEDINTOTHEVACUUM,WILLLIGHTTHEVACUUMONFIREANDMAYULTIMATELYCAUSEAHOUSEFIRE.Useabrushtocleantheflue,beingcarefulnottodamagetheESPprobeFigure5.7.Reinstallthecombustionblowerbyturningplateclockwiseto lock intoplaceandtighteningthe3wingnuts.Besurethefanplateisflushwiththeexhausthousingonthestovebodyandthemotorarmaturepointsuptowardthehopper.Slideashpanintothestoveandlatchthedoor.

Figure 5.4

F. Combustion Blower Chamber

Scrapeheatexchangerwitharrowscrapertool.

Figure 5.5

Loosen(3)thumbscrews.

Figure 5.6

Cleantheseareaswithbrushandvacuum

Figure 5.7

ESPProbeBe careful nottodamageESPp robe whencleaning withbrush.


Feeder ChamberThe chambermayget a buildupof fines from the feedermechanismmovement.Thisareashouldbecheckedandcleanedatleastonceayear.To remove the feeder cover:• Loosenthe5/16"wingnut.Figure5.8.• Liftupandslidethecoveroffofthethreadedstud.• InspectandcleantheinnerchamberifnecessaryFigure

5.9.• Reinstallthecovermakingcertainitisseatedproperlyon

thefeederbodyandtightenastightlyasyoucanbyhand.NOTE: Views are shown with the rear motor covers removed.

Pellet Metering Slide Plate

Possible pellet fines buildup area.

Figure 5.9

5/16" wing NutFeeder clean out cover

Figure 5.8

G. Pellet Feeder Chamber


6 Troubleshooting and Frequently Asked Questions

Status light error messages:3 Blinks:IndicatesthattheESP(ExhaustSensingProbe)hasfailed,hasabrokenconnection,orhasgoneoutofrangetoomanytimes.Thisrequiresamanualreset*.

4 Blinks: Can occur only in Room TempMode andindicatesRoomSensingProbe failedornot installed. IfaRoomSensingProbeistheninstalled,thestatuslightwillautomaticallyreset.

NOTE:Unitwillnotstartin"AUTO"withthisstatuserror.5 Blinks (In Igniter Auto. Mode Only):Indicatesthattheunithasfailedtolightwithinthe36minutestartcycle.Toreset-TurnModeSelectorto"OFF",thenturntoeithermodeagain.)

6 Blinks :Indicatesthatthecontrolhascalculatedpoororincompletecombustionoccurringformorethan25minutes.Asixblinkstatusmaybesetifthestoveisallowedtorunoutofpellets.Toreset,turnmodeselectorto"OFF"thenbackontothedesiredmode.Iftheunitwasnotoutofpellets,seeTroubleshootingsectionformoredetails.* Manual reset-disconnectpowercordforafewsecondsandreconnect.IferrorstilloccurscallyourDealer.

A. Error Code Description

B. Frequently Asked Questions

ISSUES SOLUTIONS1. Metallicnoise. 1. Noiseiscausedbymetalexpandingandcontractingasit

heatsupandcoolsdown,similartothesoundproducedbyafurnaceorheatingduct.Thisnoisedoesnotaffecttheoperationorlongevityofyourappliance.

2. Whiteashbuilduponglass. 2. Thisisnormal.Cleantheglassusinganynon-abrasiveglasscleaner.

3. Glasshasbuildupofblacksoot 3. Excessive build-up of ash.See solution #4.The lowerburn settings will produce more ash, the higher burnsettingsproduceless.Themoreitburnsonlowthemorefrequentcleaningoftheglassisrequired.

4. Glasshasturneddirty. 4. Excessivebuildupofash.The lowerburnsettingswillproducemoreash,thehigherburnsettingsproduceless.Themoreitburnsonlowthemorefrequentcleaningoftheglassisrequired.

5. Firehastallflameswithblacktailsandislazy. 5. Thefeedrateneedstobereducedortheburnpotneedscleaning. Heat exchanger or exhaust blower needscleaning.

6. Smokystart-uporpuffsofsmokefromtheairwash. 6. Either the burnpot is dirty or there is toomuch fuel atstart-upandnotenoughair.

7. Largeflameatstart-up. 7. This is normal. Flamewill settle down once the fire isestablished.

Contact your dealer for additional information regarding operation and troubleshooting. Visit www.harmanstoves.com to find dealer.


STOVE DOES NOT FEED1. Nofuelinhopper.2. Fireboxdraftmaybetoolowforsensingswitchinfeeder

circuit to operate.Check for closed doors, loose ormissinggasketondoorsorhopperlid.

3. Feedmotorwillnotrununtil theESPcontrolsensesacertaintemperature.Maybeyoudidnotputenoughfuelorstartinggelintheburnpotbeforemanuallylightingthefire.

4. Restrictioninthehopperorfeeder.Removeallfuelandexamine.Cleartheobstruction.

5. Feedmotorhasfailed.

PARTIALLy BURNED PELLETS1. Feedratetoohigh.2. Poorairtofuelmixture.(Checkburnpotclean-outcover

andairintake).3. Burn pot or heat exchanger tubesmay need to be

cleaned.4. Combinationofalltheabove.5. #6statusblink:A6blinkcontrolboardstatusindication

iscausedbypoororincompletecombustion.ThecircuitboardhastheabilitytotrackthecombustionthroughfeedsettingsandESPtemperatures.Whenthecontrolboardhascalculatedpoororincompletecombustion,itwillshutdown theunitasasafety feature. (Pooror incompletecombustionisacontributorofcreosotewhichmaycauseachimneyfire)

A 6 blink status may be caused by several things:1. Blockedorpartiallyblockedflue.2. Blockedorpartiallyblockedinletair.

a. Backdraft damper on the inlet pipemay be stuckclosed.

b. Ifoutsideairisinstalled,theinletcovermaybeblocked.3. Theairchamberundertheburnpotmaybefilledwithfines

andsmallbitsofash.4. Theholesintheburnpotmaybegettingfilledwithashor

carbonbuildup.5. Combustionblowerfanbladesmayneedcleaned.6. Fuelrestrictionsasnotedabove.

SMOKE SMELLSealtheventpipejointsandconnectiontostovewithsilicone.Theexhaustventistheonlypartofthesystemthatisunderpositivepressure.

FIRE HAS GONE OUT- Check for status light.1. Nofuelinhopper.2. Draftistoolow,blockedflue.3. Somethingisrestrictingfuelflow.4. Hopperlidnotclosedproperly.5. Feedmotororcombustionblowerhasfailed.

SMOKE IS VISIBLE COMING OUT OF VENT1. Air-fuelratioistoorich.

a.Feedratetoohigh.b.Drafttoolowcausedbyagasketleak.

LOw HEAT OUTPUT1. Feedratetoolow2. Drafttoolowbecauseofgasketleak.3. Poorqualityordamppellets4. Combinationof1and2.HELPFUL HINTS1. Cleaning Burn PotWheneveryourstoveisnotburning,taketheopportunitytoscrape theburnpot to removecarbonbuildup.Avacuumcleanerishandytoremovetheresidue.Besurethestoveiscoldifyouuseavacuum.Carbonbuildupcanbescrapedloosewiththefireburningusingthespecialtoolprovidedwithyourstove.Scrapethefloorandsidesoftheburnpot.Thecarbonwillbepushedoutbytheincomingfuel.Alwayswearglovestodothis.2. Removing AshesTurntheTempDialtonumber1approximately30minutesbeforeremovingashes.Thiswillresultinacoolerstoveandashpan.Maximum Feed Limit settings are not needed inmostcases.Operatinginthenormalrange(#4)isrecommendedwhenmaximumheatoutputisnotrequired.TheESPprobepreventsthestovefrombeingover-fired.Keepthestovefreeofdustanddirt.FuelTheXXVPelletStoveisapprovedforburninganygradeofpelletizedbio-massfuel.It should be noted, however, that higher ash contentwillrequiremorefrequentashremoval,scrapingoftheburnpot,andmayprovidelessBTU’sperpound.Fuel shouldnot be storedwithin the stove installationclearancesorwithin the space required for chargingandashremoval.

C. TroubleshootingWithproper installation,operation,andmaintenanceyourappliancewillprovideyearsof trouble-freeservice. Ifyoudoexperienceaproblem,thistroubleshootingguidewillassistaqualifiedservicepersoninthediagnosisofaproblemandthecorrectiveactiontobetaken.Thistroubleshootingguidecanonlybeusedbyaqualifiedservicetechnician.


7 Reference Material

A. Safety RemindersWhenoperatingyourHarman®XXVPelletStove,respectbasic safety standards.Read these instructions carefullybeforeyouattempttooperatetheXXVPelletStove.Failuretodosomayresultindamagetopropertyorpersonalinjuryandmayvoidtheproductwarranty.CAUTION: This appliance must be vented to the outside.Duetohightemperatures,thisstoveshouldbeplacedoutoftrafficandawayfromfurnitureanddraperies.Childrenandadultsshouldbealertedtothehazardsofhighsurfacetemperaturesandshouldstayawaytoavoidburntoskinand/orclothing.Youngchildrenshouldbecarefullysupervisedwhen theyareinthesameroomasthestove.Clothingandotherflammablematerialsshouldnotbeplacedonornearthisstove.Installation and repair of this stove should bedonebyaqualifiedserviceperson.Theapplianceshouldbeinspectedbeforeuseandatleastannuallybyaqualifiedserviceperson.More frequent cleaningwill be required. It is imperativethat control compartments, burners, and circulating airpassagewaysofthisstovebekeptclean.Disposal of ashes:Ashes should be placed in ametalcontainerwith a tight fitting lid.The closed container ofashesshouldbeplacedonanon-combustiblefloororontheground,wellawayfromallcombustiblematerials,pendingfinaldisposal.Iftheashesaredisposedofbyburialinsoilorotherwise locallydispersed, theyshouldberetained intheclosedcontaineruntilallcindershavethoroughlycooled.Soot and fly ash: Formationandneed for removal.Theproductsofcombustioncontainsmallparticlesofflyash.Theflyashwillcollectintheexhaustventingsystemandwillrestricttheflowofthefluegases.Pelletfuelshavedifferentashcontentsdependingonwhattypeofwoodhasbeenusedtomakethepellets.we recommend to clean the system after approximately 1 ton of pellets have been burned and judge from that how often the stove should be cleaned, remember if you change pellets it may change how often you have to clean your stove. Whenburningwoodslowly,thepotentialexistsforcreosotetoform.Theventingsystemshouldbeinspectedperiodicallythroughout theheatingseason todetermine ifacreosotebuildup has occurred. If a significant layer of creosotehasaccumulated(3mmormore),itshouldberemovedtoreducetheriskofachimneyfire. Ifafireoccurs,call thefire department, shut down the stove, and evacuate theresidence.Before using the appliance, have the ventingsystem thoroughly inspected and replace any damagedcomponents.

USE OF IMPROPER FUELS, FIRE STARTERS OR ALTERING THE STOVE FOR HIGHER HEAT OUTPUT MAy CAUSE DAMAGE TO THE STOVE AND COULD RESULT IN A HOUSE FIRE. USE ONLy APPROVED FUELS AND OPERATION GUIDELINES

WARNING!

KEEP COMBUSTIBLE MATERIALS SUCH AS GRASS, LEAVES, ETC. AT LEAST 3 FEET AwAy FROM THE POINT DIRECTLy UNDER THE VENT TERMINATION.

WARNING!

THE STOVE IS HOT wHILE IN OPERATION.KEEP CHILDREN, CLOTHING AND FURNITURE AwAy. CONTACT MAy CAUSE SKIN BURNS.

CAUTION!

THE STRUCTURAL INTEGRITy OF THE MOBILE HOME FLOOR, wALL, AND CEILING/ROOF MUST BE MAINTAINED.

CAUTION!

MOBILE/MANUFACTURED HOME GUIDELINES DO NOT ALLOw INSTALLATION IN A SLEEPING ROOM.

WARNING!

Withanyhearthappliance,installationofsmokedetectorsisrecommendedoneverylevelofthehome.Possible causes of smoke detector activation:Paintcuringprocess-Openawindowneartheapplianceforthefirstfewhoursofburning.Exhaustbeingdrawnbackinsidethedwelling-Outsideairconnectiontotheapplianceisnecessary.Ventleakage-Allinteriorseamsandjointsshouldbesealedwithsiliconewhereapplicable.Followventmanufacturersinstructionsforpropersealing.


The Low Draft Pressure Switchisadifferentialpressureswitchthatmonitors thenegativepressure (Draft) in the firebox. If thedraftbecomestoo lowforpropercombustion, theswitchopens,cuttingpowertothefeedmotorandtheignitercircuits.ThisswitchisconnectedintotheAC(highvoltage)wiring.

TheControl Board/ESP combination is responsible forall highlimitsafetycontrol.Thereare2highlimits,onenormaloperationhighlimitandonebackuphighlimit.Thecontrolhasanautomaticdiagnosticcircuit thatcontinuouslymonitors theESPandRoomSensorforfaults.Ifafaultshouldoccur,thecontrolsendsastatusalertandatthesametimetheunitgoesdowntominimumfeed/minimumburnasasafetycondition.

Backdraft Damper AssemblyAlways check to see if the damperplate swings freely inward and thatthe seating edges are not coveredwithdirtorlint.

Low Draft Pressure Switch

Feed Motor

Combustion Motor

B. Motor and Component Location

XXV Pellet Stove Safety Devices

Distribution Blower


C. Loss of PowerMinimizing Smoke During Loss of Power Using Battery Back-upHarman® strongly recommends installing battery back-up to minimize entry of smoke into the room in the event of power loss.Your pellet/biomass burning appliance relies on acombustionblowertoremoveexhaust.Apowerfailurewillcause the combustion blower to stop. This may lead toexhaustseepingintotheroom.Verticalriseintheventingmay provide natural draft. It is, however, no guaranteeagainstleakage.There are two Harman® approved battery back-up options for your appliance:Uninterruptible Power Supply UPSbatteryback-upsareavailableonlineoratcomputerandofficeequipmentstores.Your Harman® appliance with Rev E or later softwareavailable beginning in November 2010 may be pluggeddirectlyintoaHarman®approvedUPS:• The APC (American Power Conversion) model

#BE750GandtheTrippLitemodelINTERNET750Uaretestedandapproved.Otherbrandsormodelsmaynotbecompatible.

Whenpowerislost,afullychargedUPSwillpowerasafe,combustion blower only shut-down. Your appliance willpulsetheblowereveryfewsecondstoclearexhaustuntilthefireisout. NOTE: The UPS provides safe shut-down only. It is not intended for continued operation.• TheSurefire512connectstoa12voltdeepcyclebattery

thatwill runyourappliance forup toeight (8)hours. Itincludesatricklechargefeaturethatkeepsyourbatterychargedwhenpowerisavailable.NOTE:Ifthepowerisoutforlongerthanbatterylife,smokeleakagemaystilloccurunlessyourstovehasbeensafelyshutdown.

Yourappliancewillrecognizewhenpowerisrestored.Whathappens depends onESP temperature andwhether it isequippedwithautomaticignition:• In “Automatic” Mode,unitsequippedwithautomatic

ignitionwillrespondtothesetpointandESPtemperatureandresumenormaloperation.

• In “Idle” Mode,orforunitswithoutautomaticignition:• If the ESP is cool, the appliance will remain shut

down.• IfthefireisoutandtheESPisstillwarm,thefeeder

mayrestart.Sincethefireisout,theESPtemperaturewillnotrise.Theunitwillthenshut-down,andmayflashasix-blinkstatuserror.(SeeESPerrorcodes)

• If the fire is still burning, it will resume normaloperation.

Contact your dealer if you have questions about UPScompatibilitywithyourappliance.

Use only Harman® approved battery back-up devices. Other products may not operate properly, can create unsafe conditions or damage your appliance.

CAUTION!Always keep appliance doors and hopper lid closed and latched during operation and during power failures to minimize risk of smoke or burn-back.

D. Emergency Manual IgnitionHarman®pellet stovesand inserts shouldbe lit using theautomatic ignition system. This is the safest and mostreliablewayforignitingtheunit.Intheeventtheautomaticigniterisnotfunctioning,thestepsbelowmaybefollowedtomanuallylightthestoveorinsertinthe“ConstantBurn”mode. Manual lighting is for emergency purposes only,andtheignitershouldberepairedorreplacedassoonaspractical.

WARNING!Only use firestarter commercially marketed for pelletstoves and inserts, including wax coated wood chips,pellet starter gel and pellet igniter blocks. Use of anyothertypeoffirestarterisprohibited.

To avoid serious injury or death read and followmanufacturer’swarningandinstructionsforuseoffirestarter.Useoffirestarterisonlypermittedwhenperformingacoldstart.Neverattempt tomanually lightastoveor insert thathasbeen operated recently and is not at room temperature.If automatic ignition was attempted, be sure to give thestoveorinsertatleast30minutesorlongertocooltoroomtemperature.Besurethatthestoveorinsertisinthe“Igniter-Disabled”modeofoperation.Once all the precautions have been taken, follow thesesteps:1.TurntheModeSelectorto“OFF”.2.Fillburnpotwithpellets,onlyhalfway.(DoNotOverFill).3.Add firestarter to pellets following manufacturer’s

instructions.4.Lightpelletgelwithamatch,andclosethedoor,turnMode

SelectortoConstantBurn.Operationwillbeginwhenthefirereachesthepropertemperature.

WARNING!


Service Parts XXV Pellet StoveBeginning Manufacturing Date: N/A Ending Manufacturing Date: Active

12

34

5

6

78

9

1011 42

40

39

411213

14

1516

17

1819

2021

22

24

25

26 27

2829

3031

3233

34

3635

37

38

43 & 44

23

Pellet Stove

1-90-00677-2 (Charcoal) (June 2011)1-90-00677-3 (Golden re) (June 2011)1-90-00677-4 (Metallic Blue) (Jan 2010)

1-90-00677-1 (Black), 1-90-00677-14 (Majolica Brown)1-90-00677-19 (Bronze)1-90-00677-20 (Dark Blue)1-90-00677-21 (Frost)1-90-00677-22 (Black Porcelain)

Active

1-90-00025-2 (25th Anniversary Edition) (June 2009)

1-90-00677-5 (Honey Glo)(June 2009)1-90-00677-10 (Mojave Red) (Jan 2010) 1-90-00677-12 (Forest Green)( Jan 2010)

Retired units:

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor.

Stocked at Depot

ITEM DESCRIPTION COMMENTS PART NUMBER1 Pellet Tailpipe Cast 3-00-247237 Y2 Gasket, Tail Pipe/Burn Pot Pkg of 5 1-00-07381 Y

3 Right Feeder ShieldPre 008214413 1-10-677085A YPost 008214413 1-10-677885A Y

4 Left Feeder Shield 1-10-677084A YAdditional service part numbers appear on following page. 4/15

E. Service Parts




Stocked at Depot

ITEM DESCRIPTION COMMENTS PART NUMBER

5 Hopper AssemblyPre 12871 1-10-677800A

12871 Thru 008214413 1-10-677190A YPost 008214413 1-10-677206A Y

Gasket, Hopper Top 1-00-375501 YGrommet, 3/4” 3-31-960021Hopper Switch 3-20-232108 Y

6 Differential Switch 3-20-6866 Y7 Gasket, Burn Pot\Tailpipe Pkg of 5 1-00-07381 Y8 Combustion Blower 3-21-08639 Y

5” Double Blade 3-20-502221 YBlower Mounting Screws Pkg of 100 1-00-53483208Mounting Plate 1-10-677006

9 Hopper Insulation ( Pre 008219391 ) No longer Available 3-44-67703710 Hopper Hinge Plate Qty. 2 Req. 2-00-06695L11 Hinge 2-00-06694

12 Hopper KnobGold 1-00-02000Brushed Nickel 1-00-02000-8

13 Hopper Lid, Glass 3-40-247100 Y14 Hopper Lid Latch (Male and Female) 2 Sets 1-00-0669697 Y

Ball Plungers Pkg of 3 3-31-5500-3Hopper Lid Gasket 20 Ft 1-00-375501 YPush Retainers, 5/16” Pkg of 100 3-31-94807-100Screw Post Kit 20 Sets 1-00-129004 Y

15

Top Plain 4-00-677057PTop, Bronze No longer Available 1-10-677057-19

Top, BrownPre 008206292 1-10-677057-14VPost 008206292 1-10-677057-14

TopDark Blue Porcelain 1-10-677057-20Frost Porcelain 1-10-677057-21Black Porcelain 1-10-677057-22

16

Left Side Plain 4-00-677055PLeft Side, Bronze No longer Available 1-10-677055-19

Left Side, BrownPre 008206292 1-10-677055-14VPost 008206292 1-10-677055-14

Left SideDark Blue Porcelain 1-10-677055-20Frost Porcelain 1-10-677055-21Black Porcelain 1-10-677055-22

Additional service part numbers appear on following page.




Stocked at Depot

ITEM DESCRIPTION COMMENTS PART NUMBER17 Leveler Feet Pkg of 4 1-00-1230218 Airwash Reducer 1-00-67730019 Ash Door Stop 2-00-677096B20 Ash Door Gasket Retainer 2-00-677025B

Gasket, Ash Door 30 Ft 1-00-71611 Y

21

Ashlip Plain 4-00-677058PAshlip, Bronze No longer Available 1-10-677058-19

Ashlip, BrownPre 008206292 1-10-677058-14VPost 008206292 1-10-677058-14

AshlipDark Blue Porcelain 1-10-677058-20Frost Porcelain 1-10-677058-21Black Porcelain 1-10-677058-22

22 Ash Pan 1-10-677044 Y23 Ash Door Weldment 1-10-677026A24 Cable Lanyard 3-31-677070

25

Load Door Assembly Plain 1-10-677099A YLoad Door Assembly, Bronze No longer Available 1-10-677099A-19 Y

Load Door AssemblyDark Blue 1-10-677099A-20 YBlack Enamel 1-10-677099A-22 YFrost Porcelian 1-10-677099A-21 Y

Load Door Assembly, BrownPre 008206292 1-10-677099-14V YPost 008206292 1-10-677099A-14 Y

Door Only w/Rope

Plain 4-00-674053A YDark Blue 4-00-674053-20A YBlack Enamel 4-00-674053-22A YFrost Porcelian 4-00-674053-21A Y

Door Only w/Rope, BrownPre 008206292 4-00-674053-14S YPost 008206292 4-00-674053-14A Y

Air Grill Plain 3-00-677004PLatch Roller Hardware 1-00-05230 YDoor Glass w/Gasket 1-00-677000 YDoor Rope 30 Ft 1-00-00888 YGlass Clips and Hardware Pkg of 4 1-00-249140 YGlass Rope 10 Ft 1-00-1186258229 YHandle Assembly (2 Sets)

1-00-249119 YContains: Handle, 6 mm Washer, SHCS, handle, Dowel, Plunger, SSS, Bhcs

Latch Trim Plate, Enamel Only 2-00-674206PWooden Handle Pkg of 2 1-00-00247 Y

Additional service part numbers appear on following page.




Stocked at Depot

ITEM DESCRIPTION COMMENTS PART NUMBER26 Letters 2-00-677022S27 Burn Pot 1-10-00675 Y

Clean Out Cover 2 Sets 1-00-06623 YThumb Screw Pkg of 10 3-31-782108-10 Y

28 Flame Guide 3-00-03000 Y29 Ceramic Insert Gasket 3-44-724114 Y30 Distribution Blower Mount Plate 2-00-677006L31 Distribution Blower 1-00-29145 Y

Wire Kit (Needed for Bay Motor to EBM) No longer available 1-00-29045Distribution Blower Box 2-00-677023B

32 Extension Spring 3-31-218133 Hinge Plate Qty. 2 req. 3-00-674047

34

Right Side Plain 4-00-677056PRight Side, Bronze No longer Available 1-10-677056-19

Right Side, BrownPre 008206292 1-10-677056-14VPost 008206292 1-10-677056-14

Right SideDark Blue Porcelain 1-10-677056-20Frost Porcelain 1-10-677056-21Black Porcelain 1-10-677056-22

35 Air Jacket Filler Plate 2-00-677039B36 Air Jacket Post 008219391 2-00-677035B37 Hopper Heat Shield Post 008219391 2-00-677038B38 Distribution Blower Heat Shield 2-00-677041B39 Combustion Box Heat Shield 2-00-677040B40 Rear Shield Spacer 2-00-677087L41 Rear Shield Retainer 2-00-677086L42 Combustion Assembly Insulation 3-44-677042

Arrow Burn Pot Scraper Pkg of 10 2-00-773850-10Diagnostice Display Module 3-20-05401 Y

DDM Replacement Cable 1-00-05402Draft Meter Assembly 1-00-00637 Y

Draft Meter Bolt & Tube 1-00-04004Circuit Board w/Knobs & Shaft 1-00-05886 Y

6 Amp Fuse Pkg of 5 3-20-49447-5 YKnob, Control Board/D-shaft 25 Sets 1-00-015605 YLabel, Control Board 3-90-247266

Hopper Muf er and Fitting 1 Set 1-00-18186618 YAdditional service part numbers appear on following page.




Stocked at Depot

ITEM DESCRIPTION COMMENTS PART NUMBER

Igniter3-20-677200 Y

Pkg of 10 1-00-677200 YIgniter Cradle, Holder, & Flat Bottom 3 Sets 1-00-06620 YLabels, Caution & Danger 10 Ea 1-00-200408541Latch Retainer, Load Door 2-00-674098SPower Cord 3-20-39685 YRocker Switch Pre 008203932 3-20-07625Room Sensor 3-20-00906 YSilicone Tubing, 1/8" 5 Ft 1-00-5113574 Y

Touch Paint, Enamel BrownPre 008206292 1-00-6252Post 008206292 1-00-0014

Touch up Paint, BlackPre 008215076 3-42-1990Post 008215076 3-42-19905

Touch Up Paint, Bronze 3-42-0019 Y

Touch up PaintDark Blue Porcelain 1-00-0020Frost Porcelain 1-00-0021Black Porcelain 1-00-0022

Thermister Probe (ESP Probe)Pre 008200828 3-20-11744 YPost 008200828 3-20-00844 Y

Thermostat Extension 3-20-00607 YWiring Harness 3-20-08727 Y

Hardware PackagesBolt, Case Hardened Zinc Flange, 1/4-20 x 3/8 Pkg of 50 3-30-2000-50 YBolt, Grade 8.2 Zinc Flange SAE, 1/4-20 x 5/8 Pkg of 50 3-30-2002-50 YDisconnects, Female, 1/4" Pkg of 25 1-00-00959 YNut, Zinc Plated Serrated Flange Lock, 1/4-20 Pkg of 100 3-30-8024-100 YNut, Grade 5 Zinc Plated Finished Hex, 5/16"-18 Pkg of 100 3-30-8005-100 YNut, Grade 8 Yellow Zinc Finished Hex, 5/16"-18 Pkg of 100 3-30-8006-100 YScrew, Hex Washer Head TEKS Drill and Tap, #8-18 x 3/4" Pkg of 100 3-30-5003-100 YScrew, Alloy Steel Black Oxide Cup Point SSS, 1/4"-20 x 1-1/2" Pkg of 25 3-30-2011-25 YScrew, Alloy Steel Black Oxide SocketHeadCap,1/4"-20 x 2-1/4" Pkg of 50 3-30-3006-50 YScrew, BLK OX, HWH TCS 10-24X1/2 Pkg of 100 3-30-1101-100 YScrew, Grade 5 Zinc Plated Hex Cap, 1/4-20 x 1" Pkg of 50 3-30-1115-50 YScrew, Grade 5 Zinc Plated Hex Cap. 3/8-16 x 1/2" Pkg of 50 3-30-1132-50 YScrew, Hex Washer Slot T23 Zinc Thread Cutting ,1/4-20x5/8" Pkg of 50 3-30-1111-50 YShim Set Pkg of 4 2-00-677027-4Washer, Zinc Plated USS Flat Washer, 1/4" Pkg of 100 3-30-0202-100 YWasher,External Lock, 5/16" Zinc Plated Pkg of 100 3-30-0303-100 Y

Additional service parts on following page.




Stocked at Depot

ITEM Description COMMENTS PART NUMBER43 Feeder Assembly Pre 12871 1-10-677153A

43.1 Air Intake Weldment 1-10-677016W

43.2 Feeder Weldment 1-10-677150 Y43.3 Slide Plate Assembly 1-10-08037 Y43.4 Pusher Arm Assembly 1-10-01530 Y43.5 Feed Cover and Gasket 2 Sets 1-00-677152 Y43.6 Gear Motor, 4 RPM 3-20-08752 Y43.7 Sprocket Kit 1-00-06626 Y43.8 Bracket, Gear Motor 1-10-677005 Y

Grommets & Spacers Pkg of 25 1-00-960026

43.9 3/4 Feeder Tensioner 3-31-00075 Y43.10 3 1/2" Sprocket w/Hub 1-10-08550W Y43.11 Chain - 60 Pin 3-50-06667 Y43.12 3 1/2" Sprocket 2-00-06626M Y43.13 Cast Cam Block 3-00-00153 Y43.14 Cam Bearing 3-31-3014 Y43.15 Bearing Flange w/Hardware 1-00-04035 Y43.16 Auger Assembly 3-50-00465 Y43.17 Air Intake Damper Assembly 1-10-06466W

Feeder Air Crossover Kit 1-00-67900 YFeeder Replacement Kit 1-00-677150 YGasket, Feeder, Air Intake Pkg of 6 3-44-72224-6 YPillow Block Pkg of 4 3-31-3614087-4 Y

Additional service parts on following page.

43.1

43.2

43.3

43.4

43.5

43.6

43.8

43.17

43.7

43.9 43.10

43.11 43.12

43.14

43.13

43.15

43.16

#43 Feeder Assembly Pre Serial Number 12871




Stocked at Depot

ITEM Description COMMENTS PART NUMBER44 Feeder Assembly Post 12871 1-10-677189A441 Pellet Feeder Gear Motor, 4 RPM 3-20-00677 Y44.2 UL Feeder Cam Bearing 3-31-3014 Y44.3 Feeder Air Crossover Kit 1-00-67900 Y

9MM Silicone Tube 5 Ft 1-00-511427 Y44.4 Pellet Air Intake Assembly 1-10-06810A44.5 Gasket Feeder Air Intake Pkg of 6 3-44-72224-6 Y44.6 UL Feeder Air Intake 1-10-67718344.7 Gasket Ultra Air Intake Pkg of 10 3-44-677160-10 Y44.8 Ultra Feeder Weldment 1-10-724132 Y44.9 UL Feeder Pusher Arm 1-10-677131W Y

44.10 Fines De ector No longer available 2-00-677138-1044.11 Gasket, UL Feeder Cover 1-00-677122 Y44.12 Slide Plate Assembly 1-10-677121A Y44.13 UL Feeder Auger Assembly 3-50-00565 Y44.14 Bearing Flange w/Hardware 1-00-04035 Y44.15 UL Feeder Gear Motor Bracket w/Grommet 1-00-247406 Y44.16 UL Feeder Cam Block 3-00-677154 Y

Gasket, Hopper Throat 3-44-677185 YHopper Switch Feeder Fitting Pkg of 2 1-00-142818 YPillow Block Pkg of 4 3-31-3614087-4 Y

#44 Feeder Assembly Post Serial Number 12871

44.244.1

44.3

44.444.5

44.6

44.744.8

44.9

44.1044.11

44.12

44.13

44.14

44.1544.16


4021-645F02-18-13 Page1of2

Hearth & Home TechnologiesLIMITED LIFETIME wARRANTy

Hearth&HomeTechnologies,onbehalfofitshearthbrands(”HHT”),extendsthefollowingwarrantyforHHTgas,wood,pellet,coalandelectrichearthappliancesthatarepurchasedfromanHHTauthorizeddealer.

wARRANTy COVERAGE:HHTwarrantstotheoriginalowneroftheHHTapplianceatthesiteofinstallation,andtoanytransfereetakingownershipoftheapplianceatthesiteofinstallationwithintwoyearsfollowingthedateoforiginalpurchase,thattheHHTappliancewillbefreefromdefectsinmaterialsandworkmanshipatthetimeofmanufacture.Afterinstallation,ifcoveredcompo-nentsmanufacturedbyHHTarefoundtobedefectiveinmaterialsorworkmanshipduringtheapplicablewarrantyperiod,HHTwill,atitsoption,repairorreplacethecoveredcomponents.HHT,atitsowndiscretion,mayfullydischargeallofitsobligationsundersuchwarrantiesbyreplacingtheproductitselforrefundingtheverifiedpurchasepriceoftheproductitself.Themaximumamountrecoverableunderthiswarrantyislimitedtothepurchasepriceoftheproduct.Thiswarrantyissubjecttoconditions,exclusionsandlimitationsasdescribedbelow.

wARRANTy PERIOD:Warrantycoveragebeginsonthedateoforiginalpurchase.Inthecaseofnewhomeconstruction,warrantycoveragebeginsonthedateoffirstoccupancyofthedwellingorsixmonthsafterthesaleoftheproductbyanindependent,authorizedHHTdealer/distributor,whicheveroccursearlier.Thewarrantyshallcommencenolaterthan24monthsfollowingthedateofproductshipmentfromHHT,regardlessoftheinstallationoroccupancydate.Thewarrantyperiodforpartsandlaborforcoveredcomponentsisproducedinthefollowingtable.Theterm“LimitedLifetime”inthetablebelowisdefinedas:20yearsfromthebeginningdateofwarrantycoverageforgasappliances,and10yearsfromthebeginningdateofwarrantycoverageforwood,pellet,andcoalappliances.Thesetimeperiodsreflecttheminimumexpectedusefullivesofthedesignatedcomponentsundernormaloperatingconditions.

Seeconditions,exclusions,andlimitationsonnextpage.

Parts Labor Gas Wood Pellet EPAWood Coal Electric Venting

X X X X X X X

AllpartsandmaterialexceptascoveredbyConditions,

Exclusions,andLimitationslisted

X X X Igniters,electroniccomponents,andglass

X X X X X Factory-installedblowersX Moldedrefractorypanels

X Firepotsandburnpots

5years 1year X X Castingsandbaffles

7years 3years X X X Manifoldtubes,HHTchimneyandtermination

10years 1year X Burners,logsandrefractory

LimitedLifetime 3years X X X X X Fireboxandheatexchanger

X X X X X X X Allreplacementpartsbeyondwarrantyperiod

WarrantyPeriod HHTManufacturedAppliancesandVenting

1Year

ComponentsCovered

3years

2years

90Days

F. Limited Lifetime warranty


4021-645F02-18-13 Page2of2

wARRANTy CONDITIONS:• ThiswarrantyonlycoversHHTappliancesthatarepurchasedthroughanHHTauthorizeddealerordistributor.Alistof

HHTauthorizeddealersisavailableontheHHTbrandedwebsites.• ThiswarrantyisonlyvalidwhiletheHHTapplianceremainsatthesiteoforiginalinstallation.•ThiswarrantyisonlyvalidinthecountryinwhichtheHHTauthorizeddealerordistributorthatsoldtheappliance

resides.• Contactyourinstallingdealerforwarrantyservice.Iftheinstallingdealerisunabletoprovidenecessaryparts,contact

thenearestHHTauthorizeddealerorsupplier.Additionalservicefeesmayapplyifyouareseekingwarrantyservicefromadealerotherthanthedealerfromwhomyouoriginallypurchasedtheproduct.

• Checkwithyourdealerinadvanceforanycoststoyouwhenarrangingawarrantycall.Travelandshippingchargesforpartsarenotcoveredbythiswarranty.

This warranty is void if:• Theappliancehasbeenover-firedoroperatedinatmospherescontaminatedbychlorine,fluorine,orotherdamaging

chemicals.Over-firingcanbeidentifiedby,butnotlimitedto,warpedplatesortubes,rustcoloredcastiron,bubbling,crackinganddiscolorationofsteelorenamelfinishes.

• Theapplianceissubjectedtoprolongedperiodsofdampnessorcondensation.• Thereisanydamagetotheapplianceorothercomponentsduetowaterorweatherdamagewhichistheresultof,but

notlimitedto,improperchimneyorventinginstallation.

LIMITATIONS OF LIABILITy:• Theowner’sexclusiveremedyandHHT’ssoleobligationunderthiswarranty,underanyotherwarranty,expressor

implied,orincontract,tortorotherwise,shallbelimitedtoreplacement,repair,orrefund,asspecifiedabove.InnoeventwillHHTbeliableforanyincidentalorconsequentialdamagescausedbydefectsintheappliance.Somestatesdonotallowexclusionsorlimitationofincidentalorconsequentialdamages,sotheselimitationsmaynotapplytoyou.Thiswarrantygivesyouspecificrights;youmayalsohaveotherrights,whichvaryfromstatetostate.EXCEPTTOTHEEXTENTPROVIDEDBYLAW,HHTMAKESNOEXPRESSWARRANTIESOTHERTHANTHEWARRANTYSPECIFIEDHEREIN.THEDURATIONOFANYIMPLIEDWARRANTYISLIMITEDTODURATIONOFTHEEXPRESSEDWARRANTYSPECIFIEDABOVE.

wARRANTy EXCLUSIONS:Thiswarrantydoesnotcoverthefollowing:• Changesinsurfacefinishesasaresultofnormaluse.Asaheatingappliance,somechangesincolorofinteriorand

exteriorsurfacefinishesmayoccur.Thisisnotaflawandisnotcoveredunderwarranty.• Damagetoprinted,plated,orenameledsurfacescausedbyfingerprints,accidents,misuse,scratches,melteditems,

orotherexternalsourcesandresiduesleftontheplatedsurfacesfromtheuseofabrasivecleanersorpolishes.• Repairorreplacementofpartsthataresubjecttonormalwearandtearduringthewarrantyperiod.Theseparts

include:paint,wood,pelletandcoalgaskets,firebricks,grates,flameguides,batteriesandthediscolorationofglass.• Minorexpansion,contraction,ormovementofcertainpartscausingnoise.Theseconditionsarenormalandcom-

plaintsrelatedtothisnoisearenotcoveredbythiswarranty.• Damagesresultingfrom:(1)failuretoinstall,operate,ormaintaintheapplianceinaccordancewiththeinstallation

instructions,operatinginstructions,andlistingagentidentificationlabelfurnishedwiththeappliance;(2)failuretoinstalltheapplianceinaccordancewithlocalbuildingcodes;(3)shippingorimproperhandling;(4)improperopera-tion,abuse,misuse,continuedoperationwithdamaged,corrodedorfailedcomponents,accident,orimproperly/incorrectlyperformedrepairs;(5)environmentalconditions,inadequateventilation,negativepressure,ordraftingcausedbytightlysealedconstructions,insufficientmake-upairsupply,orhandlingdevicessuchasexhaustfansorforcedairfurnacesorothersuchcauses;(6)useoffuelsotherthanthosespecifiedintheoperatinginstructions;(7)installationoruseofcomponentsnotsuppliedwiththeapplianceoranyothercomponentsnotexpresslyauthorizedandapprovedbyHHT;(8)modificationoftheappliancenotexpresslyauthorizedandapprovedbyHHTinwriting;and/or(9)interruptionsorfluctuationsofelectricalpowersupplytotheappliance.

• Non-HHTventingcomponents,hearthcomponentsorotheraccessoriesusedinconjunctionwiththeappliance.• Anypartofapre-existingfireplacesysteminwhichaninsertoradecorativegasapplianceisinstalled.• HHT’sobligationunderthiswarrantydoesnotextendtotheappliance’scapabilitytoheatthedesiredspace.Informa-

tionisprovidedtoassisttheconsumerandthedealerinselectingtheproperappliancefortheapplication.Consider-ationmustbegiventoappliancelocationandconfiguration,environmentalconditions,insulationandairtightnessofthestructure.


Harman®,abrandofHearth&HomeTechnologies352MountainHouseRoad,Halifax,PA17032

www.harmanstoves.com

G. Contact Information

PleasecontactyourHarman®dealerwithanyquestionsorconcerns.ForthelocationofyournearestHarman®dealer,

pleasevisitwww.harmanstoves.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

DO NOT DISCARD THIS MANUAL

NOTICE

• Leave thismanualwithpartyresponsibleforuseandoperation.

• Important operatingand maintenanceinstructionsincluded.

• Read,understandandfollowtheseinstructionsforsafeinstallationandoperation.

Printed in U.S.A. - Copyright 2012

NOTICE: SAVE THESE INSTRUCTIONS wARNING

Documents

Transcript of NOTICE: SAVE THESE INSTRUCTIONS wARNING