�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

BEFORE YOU BEGIN

�

( )

( 1/2 )

Due to the nature of the installation,undercounter lavatories should be installedby trained and experienced installers.Do not use adhesives or adhesive sealantswith this product.Inspect the waste and supply tubing;replace if necessary.Prior to installation, unpack the new lavatoryand inspect it for damage. Return thelavatory to its protective carton until you areready to install it.Observe all local plumbing and building codes.Kohler lavatory is made according toAmerican National Standard that it canmatch the American lavatory fittings . Anyother lavatory fittings may not fit for kohlerlavatory.

SealantPenciTape measureSharp knife or scissorsKeyhole or saber sawDrill (1/2" dia. drill bit or larger)Safety glassesHammerRags or paper toweling

You may require different, morespecialized tools to install this lavatory tocountertop materials other than wood orwood composites.

TOOLS AND MATERIALS

NOTE:

(Not Supplied)

1/2

3/8 (10mm)5/8 (16mm)

1 (25mm)

Check the desired lavatory location for clearance between thebacksplash, faucet, fixture, and cabinet.Cut out the template.Carefully position and trace the template on the countertop as directedon the template.Mark the faucet hole centerline on the countertop.Drill a 1/2" pilot hole on the inside of the cut line.Cut out the countertop opening with a saber or keyhole saw.

Mark and pre-drill the wood screw holes at the locations shown on thetemplate.Waterproof any exposed areas of wood.

Position the countertop upside down on foam padding to protect thesurface. Mark and drill 3/8" (10mm) holes 5/8" (16mm) deep at thelocations shown on the template.Use a setting tool and hammer to secure the anchors.

If the countertop has not been installed, install it at this time.Drill the faucet holes according to the faucet installation instructions.Install the faucet to the countertop according to the manufacturer'sinstructions.Install the drain to the lavatory according to the manufacturer'sinstructions.

Do not use adhesives or adhesive sealants.Apply a continuous bead of quality sealant to the lavatory rim where itwill contact the countertop.

The screws provided should be used on countertops with aminimum 1" (25mm) thickness. For thinner countertops, use appropriateanchors and fasteners.

For wood, wood composite, and marble countertops, install thelavatory to the countertop with the clamps and screws provided. Forother countertop materials, refer to the countertop manufacturer'sinstructions for recommended fasteners.Position the lavatory squarely under the cutout before tightening theclamps. Draw the lavatory rim up to the countertop until it is snug.

Immediately wipe away any excess sealant.Make the final drain and faucet connection to complete the lavatoryinstallation. Be sure to follow all instructions packed with the drain andfaucet.Clean up with a cleaner.

INSTALL THE LAVATORY

FOR WOOD COUNTERTOPS

FOR MARBLE COUNTERTOPS

FOR ALL INSTALLATIONS

NOTE:

NOTE:

Donot overtighten.

non-abrasive

RIM OF LAVATORY

CLIP LOCATIONS

CUT ALONG THIS LINE

Note: before cutting countertopAllow for handle clearance

FINISHED WALL / BACK SPLASH

CENTERLINE OF FITTING

51mm

51mmMIN

65mm

375mm

473mm

Wood Screw

Anchor Screw

AS

pplyealant

Clamp

Marble

FoamPadding

Anchor

Setting Tool

10mm

16mm

Note: waterproof unprotected overhangarea on the underside of wood counter.

SEALANT

LAVATORY

MARBLE SLAB WOOD COUNTER

LAVATORY

SEALANT

356mm (Based on 305mm riser whichmay require cutting).

(T)

(S)

Pop-up drain 333mm grid drain 311mm.

333mm 311mm

356mm 305mm

(T)

(S)

57mm

192mm

57mm

45o

45o

45o

45o

CLIP LOCATIONS

K-2211T: (X)=435mm (Y)=536mm

27mm

(X)

(Y)

13mm

192mm356 333

(S) (T)

32mm 102mm10mm

K-2211T

10mm

102mm

65mm 132mm

VITREOUS CHINA UNDERCOUNTER LAVATORY/

CUT-OUT TEMPLATE / INSTALLATIONS

K-2211TCAXTON

ROUGH-IN

�

�

, 2007

Copyright Kohler China Ltd., 2007

117215-T01-D

( )IMPORTANT CONSUMERINFORMATION (CARE ANDCLEANING)

To keep your lavatory looking new, make sure yourinse it out thoroughly after each use.

on this product, as they will scratchand ruin the surface. Stubborn stains, paint, or tarcan be removed with turpentine or paint thinner.

DO NOT USEABRASIVES

6mm

NOTE: Using this template, theoverhung is about 6mm.Customers can zoom thetemplate by scale to meet theirrequirement.

(

)

( )

138

19

200021

Plumbing Fixtures and FittingsLimited One-year Warranty

Kohler plumbing fixtures and fittings are warrantedto be free of manufacturing defects.

This product is warranted for one year from date ofpurchase. Kohler China will be responsible for anyproblems caused by manufacturing defectsprovided with the invoice. Kohler China will, at itselection, repair, replace or make appropriateadjustment where Kohler China inspectiondiscloses any such defects occurring in normalusage within one year after purchase.

Implied warranties including that of merchantabilityand fitness for a particular purpose are expresslylimited in duration to the duration of this warranty,Kohler China disclaims any liability for special,incidental or consequential damages. Damages tothe product caused by misuse, abuse andinstallation that is not in accordance with theowner's manual are not covered by this warranty.

To obtain quick warranty service, please contactyour dealer, or write to Kohler China. (Original salesreceipt must be provided as the proof of purchase.)

Kohler China Investment Company Ltd.Central Customer Service Center19/F, Shanghai Square, 138 Huai Hai Road,Luwan District, Shanghai, PRCZip Code: 200021

This is our exclusive written warranty.

191mm

CLIP LOCATIONS

45o

45o

45o

45o

57mm57mm